A s s e m b l y
G u i d e
T9200, T9500, T9600,
AND T9700
PLATFORM TREADMILLS
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS, HARDWARE, & PARTS INCLUDED
5mm L-Shaped Wrench
8mm Allen Wrench
Screwdriver
PARTS BOX
Water Bottle, Qty: 1
Safety Magnet Key, Qty: 1 (except T9700)
Color-coded Hardware Bags
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE INCLUDED
BLUE BAG
ORANGE BAG
M8 x 15L Bolts
Quantity: 4
M8 x 20L Bolts
Quantity: 2
M8 x 55L Flathead Bolts
Quantity: 4
YELLOW BAG
M4 x 12L Panhead Screws
Quantity: 4
M8 x 135L Bolts
Quantity: 4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP
1
ORANGE BAG
• Slide the rubber covers on to the left
& right console supports, making sure
that the lower cutout is facing inward.
T9700: Slide the data cable down the
right console support using the white
wire tie as a guide. Make sure that
the data (1 large ribbon cable) goes
through the large hole in the lower
part of the console upright.
T9200, T9500, T9600: Slide the data
cables down the right console support
using the white wire tie as a guide.
Make sure that the data cables (one
small & one large telephone-style
cable) go through the large hole in the
lower part of the console upright.
• Insert the left console support into
the console support bracket and
secure with two bolts (M8 x 55L
Flathead) in the side of the console
support bracket.
STEP
1
• Insert one bolt (M8 x 20L) in the
rear of the console support bracket.
• Tighten all three bolts with the 5mm
Allen wrench.
• Repeat this on the right side.
NOTE: There are no data cables on
the left side.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP
BLUE BAG
2
0
:0
0
3
• Mount the console to the console
mast using four bolts (M8 x 15L) and
tighten with the 5mm Allen wrench.
NOTE: Push all extra data cable into
the console mast. Make sure not to
pinch or cut the data cable.
STEP
2
• Mount the right-hand side mount
handlebar to the console mast using
two bolts (M8 x 135L). Repeat this on
the left-hand side.
STEP
3
DATA CABLES
0
0
:
0
3
STEP
3
MODELS T9200, T9500, & T9600:
Plug in the small data cable into the
small plug connection on the lower
control board. Plug in the large data
cable into the large plug connection
on the lower control board. Slide
down the rubber covers on the left &
right console supports.
MODEL T9700: Plug the large
20-ribbon cable into the 20-pin
connection on the lower control
board. Slide down the rubber covers
on the left & right console supports.
• Install the motor cover making sure
that the rubber covers are inserted into
the motor cover. Secure the motor
cover using the six (M4 x 12L) screws
(see Yellow bag).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP
4
MODEL CONFIGURATION & AUTO-CALIBRATION
Once the Treadmill is plugged in, you need to configure the Treadmill and perform an auto-calibration to assure maximum performance.
T9700S & T9700HRT CONSOLES:
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION
Once the treadmill is plugged in, you will need to configure and run auto-calibration. With the safety key in place, turn the treadmill
on. A setup screen should appear on the console. Set your treadmill to the correct model number (9700S or 9700HRT) using the
ELEVATION arrow keys and the correct units (MI [miles]/ KM [kilometers]) using the SPEED arrow keys. If you are unsure of the model
number, you can locate the number on the front of the console. Once you have located the model number and units with the arrow
keys, press and hold SELECT. Now you can perform auto-calibration by pressing START.
The treadmill will run through minimum and maximum speed and elevation. This will take 3 to 5 minutes. Let the treadmill perform this
complete function. “END” will appear when auto-calibration is complete. When auto-calibration is complete, it will take about 30
seconds for the treadmill to reboot and return to the start-up screen.
PREMIER CONSOLE:
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION
Once the treadmill is plugged in, you will need to configure and run auto-calibration. With the safety key in place, turn the treadmill
on. A setup screen should appear on the console. Set your treadmill to the correct model number (9200, 9500, or 9600) using the
ELEVATION arrow keys and the correct units (MI [miles]/KM [kilometers]) using the SPEED arrow keys. If you are unsure of the model
number, you can locate the number on the console masts. Once you have located the model number and units with the arrow keys,
press and hold SELECT. Now you can perform auto-calibration by pressing START.
The treadmill will run through minimum and maximum speed and elevation. This will take 3 to 5 minutes. Let the treadmill perform this
complete function. “END” will appear when auto-calibration is complete. When auto-calibration is complete, it will take about 30
seconds for the treadmill to reboot and return to the start-up screen.
DELUXE CONSOLE:
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION
You need to access Engineering Mode to configure and auto-calibrate your treadmill. With the safety key in place, please hold
down ELEVATION UP and SPEED DOWN for 5 seconds. “NONE” will appear in the data window. Press the UP arrow key until
“ENG 1” appears in the data window. Press SELECT. A number will appear in the speed window. Use the SPEED arrow keys to
select your treadmill configuration (“42”- T9500 MI [miles], “43”- T9500 KM [kilometers], “44”- T9600 MI, “45”- T9600 KM, “46”-
T9200 MI, “47”- T9200 KM). If you are unsure of the model number you can locate the number on the console masts. Press SELECT
to enter your configuration. “Update” will flash on the console. Press the ELEVATION UP arrows to P14 (Eng Out). Press STOP. Press
the UP arrow key to “ENG 4”. This is auto-calibration. Press SELECT.
To begin auto-calibration, press START. The treadmill will run through minimum and maximum speed and maximum incline. The auto-
calibration will take 3-5 minutes. Let the treadmill perform this complete function before exiting the Engineering Mode. “END” will
appear in the center window when the auto-calibration is complete. When auto-calibration is complete, it will take the treadmill about
30 seconds to go to 0 elevation and return to the start-up screen with P1 showing in the function window.
SIMPLE CONSOLE:
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION
Once the treadmill is plugged in, you will need to configure and run auto-calibration. With the safety key in place, turn the treadmill
on. A setup screen should appear on the console. The large LED window displays the model number and the small LED window
displays the units. Set your treadmill to the correct model number (9200, 9500, or 9600) using the ELEVATION arrow keys and the
correct units (0 for miles and 1 for kilometers) using the SPEED arrow keys. If you are unsure of the model number, you can locate the
number on the console masts. Once you have located the model number and units with the arrow keys, press and hold SELECT. Now
you can perform auto-calibration by pressing START.
The treadmill will run through minimum and maximum speed and elevation. This will take 3 to 5 minutes. Let the treadmill perform this
complete function. “END” will appear in the window when auto-calibration is complete. When auto-calibration is complete, it will
take about 30 seconds for the treadmill to reboot and return to the start-up screen.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP
5
BELT TENSION
• If the running belt slips when used,
use the supplied 8mm Allen wrench to
turn the left and right tension bolts
1
clockwise /4-turn at a time until the
belt no longer slips.
• If the running belt is too far to the
right side, use the supplied 8mm Allen
wrench to turn the right tension bolt
1
clockwise /4-turn at a time until the
belt remains centered during use.
If the running belt is too far to the left
side, turn the left tension bolt
1
clockwise /4-turn at a time until the
STEP
5
belt remains centered during use.
500 South CP Avenue
•
P.O. Box 280
•
Lake Mills, WI 53551
fax 1.920.648.3373
toll free 1.800.335.4348
•
phone 1.920.648.4090
•
©2005 Vision Fitness. All Rights Reserved. 5.05 Part #Z92TM186-AG
AG18.12PRD
REV8
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|