Vision Fitness Home Gym 2200 HRC User Manual

R2200/2200 HRC  
ASSEMBLY INSTRUCTIONS  
To avoid possible damage to this Fitness Cycle,  
please follow these assembly instructions.  
Carefully remove all its parts from the box,  
lay them out and review the parts list.  
If any parts are missing, please call 1-800-335-4348, Ext 12  
Before proceeding, find your Fitness Cycle’s serial number,  
located on the underside of main frame, and enter here:  
______________________________  
Refer to this number when calling for service.  
I T A L L S T A R T S W I T H A V I S I O N  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R2200 Parts  
VISION FITNESS R2200 Parts Description  
Part # Description  
Count  
Dimensions  
Front Wheel Parts  
#148  
#149  
#150  
#185  
#182  
Front Foot Wheel Axle  
Front Transport Wheels  
Inside Wheel Washers  
Outside Wheel Washers  
Wheel Attachment Bolts  
1
2
2
2
2
20mm L x 8mm D  
Rear Rail Support Bars  
#106  
#182  
#91  
Rear Foot Assembly  
1
4
1
4
1
4
4
4
1
2
1
2
2
2
1
2
Rear Foot Attachment Bolts  
Rear Foot Frame Extension  
Frame Extension Bolts  
Seat Rail Support Post  
Support Post Bolts-Bottom  
Support Post Bolts-Top  
Top Post Bolt Washers  
Aluminum Seat Rail  
20mm L x 8mm D  
20mm L x 8mm D  
#182  
#96  
#186  
#182  
#184  
#121  
#181  
#125  
#124  
#188  
#189  
#129  
#174  
55mm L x 8mm D  
20mm L x 8mm D  
Seat Rail Mount Bolts  
Seat Stop Bumper Rod  
Seat Stop Bumpers  
20mm L x 8mm D  
10mm L x 3mm D  
Bumper Rod Bolts  
Bumper Rod Lock Washers  
Seat Rail End Cap  
Seat Rail End Cap Screws  
Seat Parts  
#115  
Seat Frame  
1
1
1
8
8
1
4
#137  
Seat Cushion Back  
#136  
Seat Cushion Bottom  
Seat Cushion Bolts  
#195  
55mm L x 6mm D  
20mm L x 8mm D  
#196  
Seat Cushion Bolt Washers  
Seat Mount Handlebars  
Seat Mount Handlebar Bolts  
#110  
#182  
Console Parts  
#101  
#182  
#88  
Console Mast  
1
6
1
1
1
6
Console Mast Allen Bolts  
Rubber Console Mast Cover  
Console  
20mm L x 8mm D  
11mm L x 5mm D  
#153  
#220  
#197  
Console Cable  
Console Attachment Bolts  
Other Parts  
#152  
Pedals  
2
2
1
#199  
Pedal Straps  
Power Supply  
#107  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R2200 Assembly  
NOTE: During each assembly step, ensure that ALL nuts and bolts are in  
place and partially threaded in before completely tightening any ONE bolt.  
Step 1 • Front Wheel Assembly  
1: Slide the Front Foot Axle (148) through the Front Foot Nylon Sleeves (147).  
2: Place the Inside Wheel Washers (150) on the Front Foot Axle (148).  
3: Slip the Front Transport Wheels (149) onto the Front Foot Wheel Axle  
and secure them with the outside Wheel Washers (185) and the Wheel  
Attachment Bolts (182) using two 5mm Allen wrenches.  
Step 2 • Seat Support and Rear Foot  
1: Attach the Seat Rail Support Post (96) to the top of the Rear Foot Frame  
Extension (91) with four Bottom Support Post Bolts (186). Tighten with a  
5mm Allen wrench.  
2: Secure the Rear Foot Frame Extension (91) to the frame bracket using the  
four Frame Extension Bolts (182).  
3: Secure the Rear Foot Assembly (106) to the Rear Foot Frame Extension  
(91) using the four Rear Foot Attachment Bolts (182). Tighten with a  
5mm Allen wrench.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R2200 Assembly  
Step 3 • Seat Assembly  
1: Secure the Seat Mount Handlebars (110) to the Seat  
Frame (115) with four Seat Mount Handlebar Bolts (182).  
2: When mounting the Seat Cushion Bottom (136), you  
have two sets of holes to choose from. Using the rear  
set of holes is recommended for most people. For a  
smaller person, you may choose to use the forward set  
of bolt holes. Mount the Seat Cushion Bottom (136) to  
the Seat Frame (115) with four of the Seat Cushion Bolts  
(195) and Seat Cushion Bolt Washers (196) using a 4mm  
Allen wrench. Do not fully tighten any bolt until all four  
bolts are started.  
3: Mount the Seat Cushion Back (137) to the Seat Frame  
(115) using the remaining four Seat Cushion Bolts  
(195) and Washers (196). Do not fully tighten any bolt  
until all four bolts are started.  
Step 4 • Aluminum Seat Rail  
1: Place the Aluminum Seat Rail (121) on the Seat Rail  
Support (96) and align the two holes in the Seat Rail  
with the two holes in the Frame Lip (299). Thread the  
Seat Rail Mount Bolts (182) through the Frame Lip (299)  
into the Aluminum Seat Rail but do not tighten yet.  
2: Secure the Aluminum Seat Rail (121) to the Seat Rail  
Support Post (96) with the four Top Support Post Bolts  
(182) and Top Post Bolt Washers (184). Tighten these  
four bolts. Now fully tighten the two Seat Rail Mount  
Bolts (182) at the front of the seat rail.  
3: Slide the Seat Frame (115) onto the Aluminum Seat Rail (121)  
while lifting the knob, so the seat frame will slide to the front  
of the seat rail.  
4: Slide the Seat Stop Bumper Rod (125) with one Seat Stop  
Bumper (124) already attached through the hole in the  
back of the Aluminum Seat Rail (121). Attach the second  
Seat Stop Bumper to the other end of this rod using the  
Bumper Rod Screw (188) and Bumper Rod Lock Washer (189).  
5: Press the Seat Rail End Cap (129) into the Aluminum Seat  
Rail and secure with the Seat Rail End Cap Screws (174).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R2200 Assembly  
Step 5 • Pedals  
1: Identify the left and right Pedals (152) and the left and right Pedal Straps  
(199). Attach the correct straps to each pedal, then thread each Pedal  
into the correct left and right crank arms and tighten.  
NOTE: It is very important to FULLY TIGHTEN each pedal. Failure to do  
so will result in loosening and NOISE.  
Step 6 • Console Mast  
1: Unfold the Console Cable (75) that is folded into the Frame Console  
Mast bracket. Straighten this cable and remove any kinks by drawing the  
cable through your fingers. Find the string that is attached to the inside  
of the Console Mast (101), but do not remove yet.  
2: Slide the Rubber Console Mast Cover (88) onto the Console Mast (101)  
until it is above the first waterbottle screw.  
3: Now attach the Console Cable (75) to the string located inside the  
Console Mast. Holding the Console Mast (101) above the Frame Console  
Mast Bracket, guide the Console Cable (75) through the Console Mast  
while simultaneously sliding the Console Mast onto the frame bracket.  
4: Bolt the Console Mast (101) to the frame using the six Console Mast  
Allen bolts (182). Make sure these bolts are very tight. Now slide the  
Rubber Console Mast Cover (88) back down to cover the bolt heads.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R2200 Final Assembly  
Step 7 • Console  
1: Plug the Console Cable (75) into the Console (153). The cable  
Connectors are slotted and will only fit properly one way. DO  
NOT FORCE the connection.  
2: Mount the Console (153) to the Console Mast (101) using the  
four Console Attachment Bolts (197). Make sure you DO NOT  
PINCH the Console Cable between the Console and the Console  
Mast.  
3: Plug the Power Supply Cord into the receptacle located at the  
base of the Fitness Cycle below the Seat rail. Plug the Power  
Supply (107) into an electrical outlet and begin testing  
procedures.  
Step 8 • Operation Test  
Run this simple test prior to using.  
1: Choose Intervals program, Level 8.  
2: Choose Time of “00:00”, and press Start.  
3: Your machine will now operate indefinitely. After several hours  
of operation, check for proper functioning of:  
A: Resistance Change -- change load one level at a time  
using the up and down arrows. Listen for motor noise  
(“whirr”) following each change in load, or pedal to feel  
load change.  
B: Check for display in RPMs while pedaling.  
C: Check that all LEDs will light.  
Heart Rate Control Console  
This console is manufactured with an internal wireless  
telemetric receiver that will receive heart rate signals sent to it  
by a transmitter that is worn around your chest. This wireless  
technology is accurate, continuous, and convenient. You should  
be positioned on the Fitness Cycle seat for the system to operate.  
1: On the back side of your transmitter are two rubber strips  
several inches long. These rubber strips are the electrodes that  
will pick up tthe signals of your heart beat. It is very important  
to moisten these strips with several drops of water prior to  
placing the belt against your chest. This moisture will allow the  
signals to be conducted to the transmitting hardware. If you  
ever use the bike and the display does not show a heart rate  
value, remoisten the electrodes.  
2: You will get the best results if you wear the transmitter directly  
against your skin. Once these electrodes are moistened, center  
the transmitter just below the breast or pectoral muscles with  
the Vision Fitness logo centered on the chest and facing out.  
Adjust the length of the elastic belt so that the transmitter  
presses firmly against your skin, but not so tight as to be  
uncomfortable. The transmitter will begin sending a signal as  
soon as it is worn.  
LOGO  
3: Check for heart rate feedback by testing the console in Heart  
Rate mode. Ride the Fitness Cycle at the full range of seat  
adjustments to confirm that the console is picking up the  
signal from the transmitter.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
621-D East Lake Street  
P.O. Box 280  
Lake Mills, WI 53551  
(920) 648-4090  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Thermo Products Furnace OH8FA119DV5B User Manual
Thule Automobile Accessories Kit 2161 User Manual
Trane Thermostat LS 90 User Manual
Traulsen Refrigerator RAC3T User Manual
Trek Indoor Fireplace SSDVPF CNE User Manual
Tripp Lite Network Card P222 010 User Manual
Tripp Lite TV Cables N201 020 WH User Manual
ViewSonic Car Video System Va2238w LED VA2238wm LED User Manual
VistaQuest Digital Camera VQ350 User Manual
VXI Headphones 201403B User Manual