A s s e m b l y
G u i d e
X6000DA & X6200HRT/DA
DUAL-ACTION ELLIPTICAL TRAINERS
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS, HARDWARE, & PARTS INCLUDED
MM
5 Allen Wrench
PINK BAG
MM
13 Wrench
Screwdriver
MM
M8 x 45 Bolt
Quantity: 2
(X6000DA only)
MM
M8 x 80 Bolt
Quantity: 4
M8 Nylock Nut
Quantity: 4
MM
5 L-Shaped Wrench
PARTS BOX
ORANGE BAG
Rear Folding Axle, Qty: 1 • Stabilizer w/ Rubber Cover, Qty: 2
Toe Pieces, Qty: 2 • Rear Wheels, Qty: 2
Tension Control Knob, Qty: 1 (Model X6000DA only)
Console, Qty: 1 • Power Supply, Qty: 1 (X6200HRT/DA only)
MM
• 13 Nut Cap, Qty: 2 • Water Bottle & Bracket, Qty: 1 •
Heart Rate Chest Strap, Qty: 1 (Model X6200HRT/DA only)
Parts Bags • Owner’s Guide • Assembly Guide • Warranty Card
MM
M8 x 16 Bolt
Quantity: 4
Download from Www.Somanuals.com. All Manuals Search And Download.
GREEN BAG
BLUE BAG
M8 Lock Washer
Quantity: 2
MM
M8 x 16 Bolt
M16 Wavy Washer
Quantity: 2
Quantity: 2
M8 Washer
Quantity: 2
MM
M16 Washer
Quantity: 2
M8 Washer
Quantity: 2
M5 x 25 Bolt
MM
Quantity: 1
M8 x 60 Bolt
(X6000DA only)
Quantity: 2
BLACK BAG
M8 x 25 Washer
Quantity: 2
M16 Wavy Washer
Quantity: 2
MM
M8 x 36 Bolt
Quantity: 2
MM
M6 x 12 Bolt
Quantity: 2
MM
M8 x 13 Nylock Nut
Quantity: 2
MM
M8 x 12 Bolt
M26 Wavy Washer
Quantity: 2
M8 x 35 Washer
Quantity: 2
Quantity: 4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP
1
ORANGE BAG
• Install the left and right stabilizers with
MM
the four bolts (M8 x 16 ), using the
MM
Blue 5 Allen wrench.
• Cover both stabilizers with the
included rubber covers.
• Insert the rear folding axle shaft into
the rear tube.
STEP
1
STEP
2
STEP
X6200HRT/DA
Only
2
BLUE BAG
• Slide a wavy washer (M16) onto
the right-hand side of the rear folding
axle, followed by the right-hand pedal
arm guide rail (the guide rails each
have a blue indicator arrow printed
on their sides; these arrows should
face to the outside).
• Slide a flat washer (M16) onto the
right-hand side of the rear axle,
followed by a rear wheel.
• Slide the large flat washer
(M8) onto the right-hand side of the
rear axle, and secure with a bolt
MM
(M8 x 16 ).
• Repeat above steps to install left-
hand pedal arm guide rail.
• X6200HRT/DA only: Slide the toe-
piece onto the pedal arm while
simultaneously lifting the locking knob.
Lock the toe-piece into place at the
STEP or GLIDE position.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP
3
PINK BAG
• Mount the rear pedal arms to the
front pedal arms using four bolts
MM
(M8 x 80 ) and four M8 NyLock
MM
nuts. Tighten with the 13 wrench.
• X6000DA only: Install the foot toe
pieces to the front pedal arms with
MM
two bolts (M8 x 45 ) using the Blue
MM
5 Allen wrench.
STEP
3
X6000DA
Only
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP
4
STEP
4
GREEN BAG
• X6000DA only: Unfold the RPM
sensor wire, located in the frame console
mast bracket. Remove any kinks.
• All models: Slide the rubber console
mast cover onto the bottom of console
mast, and slide it up as far as it will go.
X6000DA
• All models: Unfold the console cable
and attach it to the string located at the
bottom of the console mast. Guide the
wire up through the mast while
simultaneously sliding the console mast
onto the frame bracket.
X6200HRT/DA
• All models: Bolt the console mast
to the frame bracket with two bolts
MM
(M8 x 60 ), two flat washers
(M8), and two lock washers (M8).
MM
Tighten with the Blue 5
Allen
wrench. Slide the rubber console mast
cover back down over the bolt heads.
X6000DA NOTE: Be sure the RPM
sensor wire exits through the small slot
at the top right side of the console
mast.
• X6000DA only: Install the batteries
in the console. Mount console to
console mast using the four screws.
Plug the RPM sensor wire into the
back of the console, and feed the
excess back down into the small slot
in the console mast.
X6000DA
Only
• X6000DA only: Turn the tension
knob to Level 15. Reach inside the
console mast and connect the magnet
cables. Turn the knob to Level 1 and
MM
mount the knob using a bolt (M5 x 25 ).
• X6200HRT/DA only: Remove the
four screws from the back of the
console. Plug the wire connector from
inside the mast into the console. The
cable connector is slotted, so it may
only be connected one way; do not
force it!
• X6200HRT/DA only: Mount the
console to the mast using the four
screws. Do not pinch the cable!
• All models: Bolt the water bottle
cage to the console mast using the
two bolts located in the mast.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP
5
BLACK BAG
• Slide a large wavy washer
(M26) onto the console mast axle.
Locate and slide the right upper
handlebar bracket onto the console
mast axle and attach with a washer
(M8 x 35) and M8 NyLock nut, using
MM
the 13 wrench. Snap the plastic
MM
13 nut caps over the nuts.
STEP
5
• Slide a small wavy washer (M16)
onto the lower pedal arm support,
followed by the right lower arm.
Attach with a washer (M8 x 25) and
MM
MM
bolt (M8 x 12 ), using the Blue 5
Allen wrench.
• Pivot the lower arm and insert the
top end into the upper handlebar
MM
bracket. Attach with bolts (M7 x 35 )
MM
and (M6 x 12 ) through the side,
MM
and bolts (M8 x 12 ) from the front.
MM
Tighten using the Blue 5 Allen
wrench.
• Repeat the above steps to attach the
left-hand upper and lower arms.
621-D East Lake Street
•
P.O. Box 280
•
Lake Mills. WI 53551
fax 1.920.648.3373
toll free 1.800.335.4348
•
phone 1.920.648.4090
•
2001 Vision Fitness. All Rights Reserved. 4.01 Part #Z60EP08-AG1801PRD
AG18.01PRD
REV3
U.S. Patent No. 6,190,289
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|