User Manual
GV25-EU
GV35-EU
GV702-EU
english
deutch
francais
User Manual……………………………………………1-11
Betriebsanleitung……………………………………… xxx
Notice d’utilisation …………………………………….. xxx
nederlands Gebruiksaanwijzing……………………………………. xxx
italiano
espanol
Istruzioni sull´uso………………………………………. xxx
Instrucciones de manejo……………………………… xxx
portugues Instruções de operação……………………………….. xxx
Company information:
WWW.vipercleaning.eu
GV12066(1) – 2009-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
INTRODUCTION (CAUTION: Read the instruction manual before using the appliance)
NOTE
The numbers in brackets refer to the components shown in Machine Description chapter.
MANUAL PURPOSE AND CONTENTS
The purpose of this Manual is to provide the operator with all necessary information to use the machine properly, in a safe and
autonomous way. It contains information about technical data, safety, operation, storage, maintenance, spare parts and disposal.
Before performing any procedure on the machine, the operators and qualified technicians must read this Manual carefully. Contact
VIPER in case of doubts concerning the interpretation of the instructions and for any further information.
TARGET
This Manual is intended for operators and technicians qualified to perform the machine maintenance.
The operators must not perform procedures reserved for qualified technicians. VIPER will not be answerable for damages coming from
the non-observance of this prohibition.
HOW TO KEEP THIS MANUAL
The User Manual must be kept near the machine, inside an adequate case, away from liquids and other substances that can cause
damage to it.
DECLARATION OF CONFORMITY
The declaration of conformity, supplied with the machine, certifies the machine conformity with the law in force.
NOTE
Two copies of the original declaration of conformity are provided together with the machine documentation.
CE-declaration is print in Quick Start Guide
IDENTIFICATION DATA
The machine model and serial number are marked on the plate.
The machine model year is written in the declaration of conformity and it is also indicated by the first two figures of the machine
serial number.
This information is useful when requiring machine spare parts. Use the following table to write down the machine identification data.
MACHINE model ...............................................................................
MACHINE serial number ...................................................................
OTHER REFERENCE MANUALS
–
–
Service Manual (that can be consulted at VIPER Service Centers)
Spare Parts List (see www.vipercleaning.eu)
SPARE PARTS AND MAINTENANCE
All necessary operating, maintenance and repair procedures must be performed out by qualified personnel or by VIPER Service
Centers. Only original spare parts and accessories must be used.
Contact VIPER for service or to order spare parts and accessories, specifying the machine model and serial number.
2
GV25-EU GV35-EU GV702-EU
GV12066(1)2009-01
Download from Www.Somanuals.com. All Manuals Search And Download.
USER MANUAL
ENGLISH
CHANGES AND IMPROVEMENTS
VIPER constantly improves its products and reserves the right to make changes and improvements at its discretion without being
obliged to apply such benefits to the machines that were previously sold.
Any change and/or addition of accessories must be approved and performed by VIPER.
OPERATION CAPABILITIES
This dry and wet vacuum cleaner is a cleaning appliance for professional use and is suitable for commercial use, for example in
hotels, schools, hospitals, factories, shops, offices, and rental businesses., The appliance is intended for the dry and wet vacuum
cleaning of textile floorings and wall coverings, sucking up dust and liquids.
CONVENTIONS
Forward, backward, front, rear, left or right and up are intended with reference to the operator’s position, that is to say in working
position with the handle.
UNPACKING/DELIVERY
To unpack the machine, carefully follow the instructions on the packing.
When the machine is delivered, check that the packing and the machine were not damaged during transportation. In case of visible
damages, keep the packing and have it checked by the carrier that delivered it. Call the carrier immediately to fill in a damage claim.
Check that the machine is equipped with the following features:
1. Technical documents:
•
•
VACUUM CLEANER User Manual
VACUUM CLEANER Spare Parts List
SAFETY
The following symbols indicate potentially dangerous situations. Always read this information carefully and take all necessary
precautions to safeguard people and property.
The operator's cooperation is essential in order to prevent injury. No accident prevention program is effective without the total
cooperation of the person responsible for the machine operation. Most of the accidents that may occur in a factory, while working
or moving around, are caused by failure to comply with the simplest rules for exercising prudence. A careful and prudent operator is
the best guarantee against accidents and is essential for successful completion of any prevention program.
SYMBOLS
DANGER!
It indicates a dangerous situation with risk of death for the operator.
WARNING!
It indicates a potential risk of injury for people or damage to objects.
CAUTION!
It indicates a caution related to important or
useful functions. Pay careful attention to the
paragraphs marked by this symbol.
NOTE
It indicates the necessity to refer to the User Manual before performing any procedure.
GV12066(1)2009-01
GV25-EU GV35-EU GV702-EU
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
GENERAL INSTRUCTIONS
Specific warnings and cautions to inform about potential damages to people and machine are shown below.
DANGER!
–
–
Always disconnect the power supply cable when the machine is not in use, before performing maintenance
procedures and before replacing parts or converting the appliance to another .
This machine must be used by properly trained and authorised personnel only. Children or disabled people cannot
use this machine.
–
–
–
Do not wear jewels when working near electrical components.
Do not work under the lifted machine without supporting it with safety stands.
Do not operate the machine near toxic, dangerous, flammable and/or explosive powders, liquids or vapours.
WARNING!
–
–
–
The machine power supply cable is grounded and the relevant plug is grounded too. In case of machine malfunction
or breakdown, grounding connection reduces the risk of electric shock.
The power supply cable plug must be connected to an appropriate outlet, which is grounded according to law in
force.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
–
–
Children should be supervised to ensure that they do not play with the appliance.
if the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
–
–
–
–
Improper connection can cause electric shock. Consult a qualified technician to make sure that the outlet is properly
grounded.
Do not tamper with the power supply cable plug. If the power supply cable plug cannot be connected to the outlet,
have new grounded outlet installed by a qualified technician, according to the law in force.
Before connecting the power supply cable to the electrical mains, check that frequency and voltage, shown on the
machine serial number plate, match the electrical mains voltage.
Regularly examine the supply cable for damage, such as cracking or ageing, cuts, etc. If the damaged is found, replace
the cord before further use.
–
–
To avoid any risk, if the power supply cable is damaged, contact VIPER Service Center or a qualified technician.
Do not pull or carry the machine by the power supply cable and never use the power supply cable as a handle. Do not
close a door on the power supply cable, or pull the power supply cable around sharp edges or corners. Do not run
the machine on the power supply cable.
–
–
Keep the power supply cable away from heated surfaces.
To reduce the risk of fire, electric shock, or injury, do not leave the machine unattended when it is plugged in.
Disconnect the machine from the electrical mains when not in use and before performing maintenance procedures.
To avoid electric shock, do not expose the machine to rain or other bad weather conditions. Store the machine
indoors, in a dry place.
–
–
–
–
Do not allow to be used as a toy. Close attention is necessary when used near children.
Use only as shown in this Manual. Use only VIPER's recommended accessories.
Take all necessary precautions to prevent hair, jewels and loose clothes from being caught by the machine moving
parts.
–
–
–
–
–
–
–
–
–
Do not leave the machine unattended without being sure that it cannot move independently.
While using this machine, take care not to cause damage to people or objects.
Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects.
Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present .
Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes..
Use extra care when cleaning on stairs.
This appliance is not suitable for picking up hazardous dust.
This appliance is for dry use only and is not be used or stored outdoors in wet conditions.
This appliance is suitable for commercial use, for example in hotels, schools, hospitals, shops, offices, and rental
businesses.
–
–
The machine working temperature must be between 0°C and +40°C.
The machine storage temperature must be between 0°C and +40°C.
4
GV25-EU GV35-EU GV702-EU
GV12066(1)2009-01
Download from Www.Somanuals.com. All Manuals Search And Download.
USER MANUAL
ENGLISH
–
–
–
–
–
–
The humidity must be between 30% and 95%.
Do not use the machine as a means of transport.
Do not use the machine on slopes with a gradient exceeding the specifications.
In case of fire, use a powder fire extinguisher, not a water one.
Do not tamper with the machine safety guards and follow the ordinary maintenance instructions scrupulously.
Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged. Always keep
the openings free from dust, hairs and any other foreign material which could reduce the air flow.
Do not remove or modify the plates affixed to the machine.
–
–
If the machine is used according to the instructions, the vibrations are not dangerous. The machine vibration level is
less than 2.5 m/s2 (98/37/EEC-EN 1033/1995).
–
–
This machine cannot be used on roads or public streets.
Pay attention during machine transportation when temperature is below freezing point. The water in the recovery tank
or in the hoses could freeze and seriously damage the machine.
–
–
In case of machine malfunctions, ensure that these are not due to lack of maintenance. If necessary, request
assistance from the authorised personnel or from an authorised Service Center.
If the machine
•
•
•
•
•
does not work properly
is damaged
has water or foam leaks
has been left outdoors exposed to bad weather conditions
is wet or has been dropped into water
turn it off immediately and contact VIPER Service Center or a qualified technician.
If parts must be replaced, require ORIGINAL spare parts from an Authorised Dealer or Retailer.
To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of this
Manual, must be performed by the authorised personnel or by an authorised Service Center.
If foam or liquid escapes from the appliance, switch off immediately.
Regularly clean the water level limiting device in accordance with instructions and examine it for signs of damage.
Carefully read all the instructions before performing any maintenance/repair procedure.
Do not wash the machine with direct or pressurized water jets, or with corrosive substances.
WARNING only use the accessory provide with the appliance, The use of other non original accessory may impair
safety.
–
–
–
–
–
–
–
–
The machine must be disposed of properly, because of the presence of toxic-harmful materials (electrical components,
etc.), which are subject to standards that require disposal in special centres (see Scrapping chapter).
GV12066(1)2009-01
GV25-EU GV35-EU GV702-EU
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
MACHINE DESCRIPTION
MACHINE STRUCTURE（GV25-EU GV35-EU）
1. Handle
2. Cover
6. Caster
7. Mounting base
8. Intake
3. Mains cord
4. Catch
9. On/off switch
5. Tank
MACHINE STRUCTURE（GV702-EU）
1. Carring handle
2. On/off switch
3. Top cover
4. Tank
9. Castor
10. Wheel
11. Support
12. Clamp
5. Intake
13. Catch
6. Outlet
14. Handle
15. Mains cord
16. Head cover
7. Handle lift
8. Mounting base
16
1
2
15
14
1
2
3
3
9
4
4
5
13
5
12
11
8
6
7
7
10
8
6
9
GV25-EU、GV35-EU
GV702-EU
6
GV25-EU GV35-EU GV702-EU
GV12066(1)2009-01
Download from Www.Somanuals.com. All Manuals Search And Download.
USER MANUAL
ENGLISH
STANDARD ACCESSORY SET (GV25-EU GV35-EU)
1. Wet pick-up tool (300mm)
2. Crevice tool
5. Hose
6. Upholstery tool
3. Combination tool
4. Tube
7. Dusting tool
4
4
2
3
5
1
7
6
STANDARD ACCESSORY SET (GV702-EU)
1. Combination tool
2. Upholstery tool
3. Dusting tool
4. Crevice tool
5. Tube
6. Paper bag
7. Filter basket with cotton cloth
8. Hose
9. Filter
3
2
4
5
3
6
1
7
TECHNICAL DATA
GV25-EU
220 V-240V
1100W
GV35-EU
220 V-240V
1100W
GV702-EU
Model
Voltage
220 V-240V
2200W
Power
Current
5 A
5 A
10 A
Frequency
Capacitor
Vacuum
50-60Hz
25L
50-60Hz
35L
50-60Hz
70L
2032mmH2O
3398L/Min
65 dB(A)
12kg
2032mmH2O
3398L/Min
65 dB(A)
13kg
2032mmH2O
6796L/Min
65 dB(A)
26.3kg
Flow rate
Sound pressure level at workstation
Weight
Length of Power cord
10m
10m
10m
GV12066(1)2009-0
GV25-EU GV35-EU GV702-EU
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
WIRING DIAGRAM FOR GV25-EU GV35-EU
SWITCH
EMI
BROWN
220V
BROWN
BLUE
G/Y
50/60HZ
BLUE
SINGLE
PHASE
Motor
G/Y
SUPPLY
H05RN-F 3X0.75
Power
Supply
Cord
WIRING DIAGRAM FOR GV702-EU
SWITCH NO1
EMI
BROWN
BLUE
G/Y
BROWN
220V
50/60HZ
SINGLE
PHASE
SUPPLY
Motor
Motor
BLUE
SWITCH NO2
BROWN
BLUE
BROWN
BLUE
H05RN-F 3X1
Power
Supply
Cord
G/Y
8
GV25-EU GV35-EU GV702-EU
GV12066(1)2009-01
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
USER MANUAL
ENGLISH
OPERATION OF VACUUM CLEANER
BASIC OPERATION
1. Check that the electrical switch is switched off,
2. Then connect the suction hose (1) into the suction inlet (2) at the machine
by pushing the hose forward until it is sliding in place at the inlet (to release
the hose from machine just twist and pull out the hose).
2
1
2
3. Then connect the tubes (1) with the hose handle (2), twist the tubes in order
to ensure that they are properly fitted.
4. Attach suitable nozzle (3) to the tube (1), Choose nozzle depending on what
type of material that is to be picked-up.
4
1
5. Connect the plug into a proper electrical outlet
1
6. Put the electrical switch (4) into position ”I” in order to start the motor.
(GV702 has two motors/fan units and two electrical switches –one switch
for each motor).
3
Dry Operation
The use of a cloth filter bag and a dust bag will improve levels of filtration and is recommended. Always ensure that
the container is emptied of any liquid before using for dry pick-up and that the cloth filter is in a clean and dry
condition.
Empty the tank when you notice that the performance is reducing or after dry pick-up.
1. Switch off the machine, Release the latches (1) by pulling them outwards so
that the motor top (2) is released, and remove the motor top (2).
2. Shake the filter (3) in order to remove debris. This should be done while the
hose is still connected to avoid dust exiting from the open dirt container
connection. After shaking the filter, wait a few moments for the dust to settle.
2
1
Remove filter (3) from machine and empty container (4). If the filter’s
surface appears to be heavily soiled, it is advisable to brush the filter
material clean with an ordinary soft household brush. This ensures
continued peak performance.
3. Having emptied container (4), replace filter (3) and the motor top (2). Make
sure that the switch/switches is located in direction towards the suction inlet.
You are now ready to start again.
4
3
Wet pick up
The float valve assembly must be used at all times for wet pick-up that shuts off the airflow through the machine
when the maximum liquid level is reached.
Always ensure that the container is emptied of any dry dust before using the machine for wet pick-up.
Always be sure to use a wet pick-up nozzle with rubber blades.
During wet pick-up operation the floor is left almost entirely dry.
When there is no longer liquid to be collected or the machine is full, switch off the power head, unplug the vacuum
cleaner, empty the container.
Emptying GV25-EU GV35-EU
1. Release the latches (1) by pulling the lower parts outwards so that the motor
top (2) is released, Remove the motor top (2).
3
2. Disconnect the hose (3) from the inlet (4) by screwing the hose outwards.
2
1
4
GV12066(1)2009-01
GV25-EU GV35-EU GV702-EU
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
USER MANUAL
3. Empty by tilting the container (1) backwards and pour the liquids into a floor
drain or similar.
3
4. Wipe float valve (2), filter (3) and the motor top with a damp cloth before the
motor top is reinstalled to the container.
2
1
5. Replace the float valve assembly and power head. Secure with the latches.
Emptying GV702-EU
1
1. Drain hose: This mode has a draining hose (1) that easy and comfortable
drain the container from liquids, Detach the drain hose (1) from the bracket
(2) by pulling hose backwards from the cleaner. Place the drain hose end
near a floor drain and then remove the plug at hose end. The natural
pressure will then drain the liquids from the container.
2
2. Emptying from the container: Pull the lower parts of the latches outwards
and release the motor top. Remove the motor top.
3
3. The suction hose can be attached during emptying from the container (3).
Grasp with on hand at the handle at the lower part of the container. To
avoid movement of the trolley-place, one foot at the base part (4) of the
trolley. Then tilt the container backwards and pour the liquids into a floor
drain or similar.
4
4. Wipe float valve (5), filter (6) and the motor top with a damp cloth before the
motor top is reinstalled to the container.
6
5. Replace the motor top. Secure with the latches.
5
MAINTENANCE
To keep the machine performing well for many years, Please follow the following maintenance procedures.
﹡Always confirm that the machine is unplugged prior to performing any maintenance or repairs.
1] Make sure that the cable is not cut or damaged. (If it is, contact the nearest authorized service center for
replacement)
2] Thoroughly clean the tank, do not let it sit for a long time with dust or dirty water.
3] The cloth dust bag can be washed and must be completely dry before use.
3] Lubricate casters with a water resistant lubricant every month.
4] Check machine for loose or missing nuts and bolts and replace as necessary.
5] Check the filter, and clean it after each use.
6] The motor is built for maintenance-free operation and does not need any particular service. The carbon brushes
may need to be replaced due to normal wear and tear caused by using the vacuum cleaner over time, and they
can be replaced only by an authorized VIPER distributor.
ATTENTION
1. To avoid the risk of electrical shock, always insure the four insulation bush (1) are
installed.
1
10
GV25-EU GV35-EU GV702-EU
GV12066(1)2009-01
Download from Www.Somanuals.com. All Manuals Search And Download.
USER MANUAL
ENGLISH
STORAGE
1] Unplug machine from power source.
2] Store in upright position in a dry area.
Do not dispose of electrical appliances as unsorted municipal waste, use separate
collection facilities.
GV12066(1)2009-01
GV25-EU GV35-EU GV702-EU
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|