VENTILATION
Built-In 10”H. Wall Hood w/Ventilator/
12”H. Chimney Wall Hood w/Ventilator
Standard Features & Accessories
All models include
• Heavy-duty construction
Professional 10”H. hoods include
ranges, 30”W. non-griddle/grill
rangetops, and 30”W. cooktops
• VWH3610—36”W.
o Recommended for use with 36”W.
non-griddle/grill ranges, 36”W. non-
griddle/grill rangetops, and 36”W.
cooktops
o Virtually seamless stainless steel
design with no visible screws
• Heat sensor turns the ventilator on full
power when cooking temperatures
reach uncomfortable levels
• Recommended for 24”W., 30”W. &
36”W. non-griddle/grill ranges,
rangetops, and cooktops
• Commercial-type size, design, and styling
• Allow replacement of most older
hoods with minimal cabinet alteration
• Commercial-type baffle filter system
efficiently removes grease and heated
vapors from the air; especially
designed for use with commercial-
type products
DESIGNER CHIMNEY WALL HOODS,
12”H./24”D.
• 460 CFM interior-power ventilator
comes standard with product
o Variable speed controls for custom
venting—separate on/off switch
allows you to leave ventilator at
favorite/most-used setting
• Two 50-watt halogen lights with
dimmer control
o Power switch and dimmer control
are separate, allowing you to leave
dimmer at favorite position
Designer 12”H. hoods include
• Professional-type size, design, and
styling
• Delay function—can be set to shut off
from 10 – 30 minutes later (10 min.
increments)
• 12-hour timer built into controls
• Two dishwasher-safe stainless steel
mesh filters are easily removed for
quick cleaning (frame and mesh are
stainless steel)
• DCH3042—30”W.
o Recommended for use with 30”W.
ranges, 30”W. non-griddle/grill
rangetops, and 30”W. cooktops
• DCH3642—36”W.
o Recommended for use with 36”W.
ranges, 36”W. non-griddle/grill
rangetops, and 36”W. cooktops
• Easy cleanup
Model numbers
o Design of low-profile filter system
means less interior hood space to
be cleaned
o Canopy interior is completely lined
in stainless steel for increased
rigidity, seamless appearance, and
easy cleaning
PROFESSIONAL WALL HOODS, 10”H./21”D.
• VWH2410—24”W.
o Recommended for use with 24”W.
non-griddle/grill ranges (for larger
equipment, use 18”H. hood)
• VWH3010—30”W.
o Recommended for use with 30”W.
Model Options
VWH Professional
Wall Hood
DCH Designer Chimney
Wall Hood
FINISH DETAILS FOR PROFESSIONAL MODELS
Racing Red (RR), Apple Red (AR),
Burgundy (BU), Plum (PL), Chocolate
(CH), and Cobalt Blue (CB).
supports/brackets and hooks
(included).
o Brass Trim Option (BR)—nameplate,
rail, supports/brackets, and hooks
(included). Brass components have a
durable protective coating for
• Stainless Steel (SS), Black (BK), White
(WH), Metallic Silver (MS), Graphite Gray
(GG), Stone Gray (SG), Taupe (TP), Biscuit
(BT), Cotton White (CW), Oyster Gray
(OG), Golden Mist (GM), Lemonade (LE),
Sage (SA), Mint Julep (MJ), Sea Glass
(SE), Iridescent Blue (IB), Viking Blue (VB),
Pumpkin (PM), Racing Red (RR), Apple
Red (AR), Burgundy (BU), Plum (PL),
Chocolate (CH), and Cobalt Blue (CB).
• Finish designates front and sides.
• Accessory Rail Option—Front of hood.
(Must be ordered factory installed)
o Stainless Steel/Chrome (CR)—
• Finish designates front and sides.
• Accessory Rail Option—Front of hood.
(Must be ordered factory installed)
o Stainless Steel/Chrome (CR)—
Stainless steel rail with chrome
supports/brackets and hooks
(included).
o Brass Trim Option (BR)—rail,
supports/brackets, and hooks
(included). Brass components have a
durable protective coating for
maintenance-free normal use.
maintenance-free normal use.
FINISH DETAILS DESIGNER MODELS
• Stainless Steel (SS), Black (BK), White
(WH), Metallic Silver (MS), Graphite
Gray (GG), Stone Gray (SG), Taupe
(TP), Biscuit (BT), Cotton White (CW),
Oyster Gray (OG), Golden Mist (GM),
Lemonade (LE), Sage (SA), Mint Julep
(MJ), Sea Glass (SE), Iridescent Blue
(IB), Viking Blue (VB), Pumpkin (PM),
Stainless steel rail with chrome
ORDERING INSTRUCTIONS
First specify model number, followed by color code (VWH2410SS). If ordering optional decorative rail, specify code at end
(VWH2410SSCR).
PLANNING AND DESIGN GUIDE
RELEASED 12/1/07
©2007 VRC— INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTILATION
Built-In 10”H. Wall Hood w/Ventilator/
12”H. Chimney Wall Hood w/Ventilator
Dimensions & Specifications
CLEARANCE DIMENSIONS
60”min.
24”min.
(15
(61.0 cm)
2.4 cm)
to
63”max.
to
27”max.*
(16
(68.6 cm)
0.0 cm)
36”
(91.4 cm)
PROFESSIONAL
*Note: When installing with a 24” high-shelf, the
27” (68.6 cm) max. dimensions must be used.
66”min.
30”min.
(167.6 cm)
(76.2 cm)
to
69”max.
to
33”max.
(175.3 cm)
(83.8 cm)
36”
cm)
(91.4
DESIGNER
PLANNING AND DESIGN GUIDE
RELEASED 12/1/07
©2007 VRC— INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTILATION
Built-In 10”H. Wall Hood w/Ventilator/
12”H. Chimney Wall Hood w/Ventilator
Installation Requirements
VWH Professional
Wall Hood
DCH Designer Chimney
Wall Hood
UTILITY REQUIREMENTS
Proper installation/ ducting is
extremely important to ensure
maximum performance. Use a qualified
and trained installer.
o Straight runs and
gradual turns are best; for
example, each 90° elbow
is equivalent to 5’ – 10’
(1.52 – 3.05 cm) of
ELECTRICAL
• Hardwire direct with two-wire
with ground
• 120 VAC/60 Hz
• Max. amp usage—5.6
DUCTING
straight run.
• 460 CFM interior (blower
included)
• 7” round duct
PLUMBING
Not applicable
o Never use flexible duct; it
creates back pressure/air
turbulence and greatly
reduces performance.
• Check with a qualified and
trained installer for local
codes and makeup air
requirements, if any.
• Max. duct run length—50’
(152.4 m)
GAS
Not applicable
o Duct run length is for
general reference only;
for longer duct runs,
increase duct size and
contact a qualified and
trained installer.
Note: All CFMs are based on tests with 0.1 static pressure. Without applying static pressure (some brands do not), CFM could be
greatly overstated.
Model
Interior Ventilator Kits
460 CFM standard
460 CFM standard
460 CFM standard
460 CFM standard
460 CFM standard
Interior Duct Size
7” (17.8 cm)
Interior Max. Amps
VWH2410
VWH3010
VWH3610
DCH3042
DCH3642
5.6
5.6
5.6
5.6
5.6
7” (17.8 cm)
7” (17.8 cm)
7” (17.8 cm)
7” (17.8 cm)
PLANNING AND DESIGN GUIDE
RELEASED 12/1/07
©2007 VRC— INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTILATION
Built-In 10”H. Wall Hood w/Ventilator/
12”H. Chimney Wall Hood w/Ventilator
Installation Notes & Accessories
✪
Recirculating Hood Conversion Kits
• Stainless Steel (SS)
• Eliminates ducting
• Kit includes
o Two charcoal filters
o Installation hardware
o Top vent/grille
• Professional—4”H. x 12”D.
• Designer—2”H. x 12”D.
Model
VRK24
VRK30
VRK36
DRK30
DRK36
Description
Approx. ship wt. lbs. (kg)
Professional 24”W. conversion kit
Professional 30”W. conversion kit
Professional 36”W. conversion kit
Designer 30”W. conversion kit
Designer 36”W. conversion kit
10 (4.5)
13 (5.9)
16 (7.3)
15.4 (7)
15.4 (7)
Charcoal Filters
• For use with VRK & DRK conversion kits
• Recommended replacement every 6 – 12 months
Model
CFV11
CFV13
CF-D12
CF-D14
Description
Approx. ship wt. lbs. (kg)
Professional hood filter for 24”W.
Professional hood filter for 30”W. & 36”W.
Designer hood filter for 30”W.
Designer hood filter for 36”W.
1 (0.5)
2 (0.9)
2 (0.9)
2 (0.9)
Duct Covers
• Specify finish code following accessory model number (for example, DCW24-SS)
o Professional models
• For VWH hoods
• 12”D.
• Extends height of hood by 12”—conceals duct
• Available in Stainless Steel (SS), Black (BK), White (WH), Almond (AL), Biscuit (BT), Stone Gray (SG), Graphite Gray
(GG), Burgundy (BU), Lemonade (LE), Mint Julep (MJ), Forest Green (FG), Viking Blue (VB), Cobalt Blue (CB), and
Eggplant (EP).
o Designer models
• For DCH hoods
• For 8’ – 9’ ceilings
• Available in Stainless Steel (SS), Black (BK), White (WH), Biscuit (BT), Stone Gray (SG), Graphite Gray (GG).
• Not needed if using a DCLF1610
Model
DCW24
DCW30
DCW36
DCC16
Description
Approx. ship wt. lbs. (kg)
9 (4.0)
Professional 24”W. duct cover
Professional 30”W. duct cover
Professional 36”W. duct cover
Designer adjustable duct cover – for DCH 30” & 36” models
10 (4.5)
11 (5.0)
20 (9.0)
PLANNING AND DESIGN GUIDE
RELEASED 12/1/07
©2007 VRC— INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTILATION
Built-In 10”H. Wall Hood w/Ventilator/
12”H. Chimney Wall Hood w/Ventilator
Installation Notes & Accessories
✪
Duct Cover Extension
• For DCH hoods
• 16”W. x 12”D. x 28 – 40”H.
• Extends height of hood by up to 12” (for 10’ ceilings)
• Replaces adjustable duct cover supplied standard with hood
• Specify finish code following accessory model number (for example, DCCE1610-SS)
• Available in Stainless Steel (SS), Black (BK), White (WH), Biscuit (BT), Stone Gray (SG), Graphite Gray (GG).
Model
Description
Approx. ship wt. lbs. (kg)
DCCE1610
Designer duct cover extension
7 (15.4)
Backsplashes
• Stainless Steel (SS)
• 30”H.
• For both VWH & DCH hoods
• Backsplashes protect the wall space below hood
• Create a continuous finish between cooking surface and hood
• Low maintenance, easy to clean
• Hemmed edges with screw holes
• Kit includes backsplash and fastening screws
Model
BKS24
BKS30
BKS36
Description
Approx. ship wt. lbs. (kg)
24”W. backsplash
30”W. backsplash
36”W. backsplash
5 (2.3)
7 (3.2)
9 (4.1)
Warming Shelf Panels
• Stainless Steel (SS)
• 12”D. X 12”H.
• For both VWH & DCH hoods
• Shelf panels hold cookware and condiments
• Kit includes shelf (or shelves) and fastening screws
• Fold up/down, heavy-duty warming shelves (non-removable), factory installed on stainless steel backsplash
• 5-7/8”W. X 10-1/8”D.
Model
WGP24
WGP30
WGP36
Description
Approx. ship wt. lbs. (kg)
24”W. warming shelf panel (one shelf)
30”W. warming shelf panel (one shelf)
36”W. warming shelf panel (two shelves)
6 (2.7)
9 (4.1)
12 (5.4)
Compliance Information
WARRANTY SUMMARY*
• One-year full warranty—complete product
• Five-year limited warranty—all ventilator motors
• Ninety-day limited warranty—cosmetic parts such as glass, painted, and decorative items
* For complete warranty see Use & Care Guide. Warranty valid on Viking products shipped within the United States and Canada.
PLANNING AND DESIGN GUIDE
RELEASED 12/1/07
©2007 VRC— INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
Download from Www.Somanuals.com. All Manuals Search And Download.
|