ViewSonic Projector S50 X50 User Manual

S50/X50  
Multimedia Projector  
Operator's Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This liquid crystal projector is used to project  
various computer signals as well as NTSC / PAL /  
SECAM video signals onto a screen. Little space  
is required for installation and large images can  
easily be realized.  
PROJECTOR  
FEATURES  
Ultra High Brightness  
Keystone Distortion Correction  
G
G
Crisp, ultra-bright presentations is achieved  
by using a UHB (ultra high brightness) lamp  
and a highly efficient optical system  
Quick correction of distorted images electrically  
Partial Magnification Function  
Whisper Mode Equipped  
G
G
Interesting parts of images can be magnified  
for closer viewing  
Special mode is available for reducing  
projector noise to achieve quieter operation  
Your projector should come with the items  
shown below. Check to make sure that all the  
items are included. Contact your dealer if  
anything is missing.  
PREPARATIONS  
NOTE Keep the original packing material for future reshipment.  
Power cord  
(UK Type)  
Power cord  
(Europe Type)  
Power cord  
(US Type)  
Projector  
S50/X50  
Multimedia Projector  
/jtli
rateur  
tch  
/lij
/tti
/ittil
/
íl ario  
' eratore  
zing  
rador  
Video/Audio  
Componet Video  
RGB cable  
cable  
cable  
(with white lead)  
(with green lead)  
Operator's Guide  
Product Safety Guide  
Warranty  
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
ASPECT  
BLANK  
VOLUME  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
Quick Start Guide  
PAGE DOWN  
MUTE  
OFF  
FREEZE  
KEYSTONE  
POSITION  
MENU  
Two AA batteries  
(for the remote  
control)  
ENTER  
USB mouse  
cable  
ESC  
RESET  
Remote control  
Soft case  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING Precautions to observe in regards to the power cord: Please use extra  
caution when connecting the projector's power cord as incorrect or faulty  
connections may result in FIRE AND/OR ELECTRICAL SHOCK. Please adhere to the  
following safety guidelines to insure safe operation of the projector:  
Only plug the power cord into outlets rated for use with the power cord's specified voltage range.  
Only use the power cord that came with the projector.  
NEVER ATTEMPT TO DEFEAT THE GROUND CONNECTION OF THE THREE-  
PRONGED PLUG!  
Make sure that you firmly connect the power cord to the projector and wall outlet.  
Connect your devices to the projector  
Connect your computer, VCR and/or other  
devices you will be using to the projector.  
8
12  
1
Insert the batteries into the remote  
control  
13  
2
3
Connect the power cord  
(1) Connect the connector of the electrical power cord to the AC inlet of the main unit.  
(2) Firmly plug the power cord's plug into the outlet  
Power outlet  
(1)  
(2)  
AC inlet  
Power cord  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
THE PROJECTOR  
PART NAMES  
Indicates the corresponding  
reference page  
keystone button  
20  
23  
menu button  
reset button  
29  
rgb button  
15  
23  
,
,
,
cursor buttons  
video button  
15  
14 on/off button  
Remote sensor  
13  
Power switch 14  
Lens  
Elavator foot  
3
AC power inlet  
6
Elevator button  
Focus ring  
6
15  
31 lamp indicator  
Zoom ring  
15  
temp indicator  
32  
power indicator  
14  
Air filter  
32  
Speaker  
Terminal panel  
6
Rear adjuster foot  
10  
rgb in 1 port  
13  
Remote sensor  
11  
s-video in port  
rgb in 2 port  
10  
video in port  
audio in L port  
audio in R port  
11  
10  
10  
component video  
11  
11  
11  
C
R/PR port  
component video  
CB/PB port  
10 coontrol port  
component video  
Y port  
rgb out port  
12  
usb port  
10  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
THE REMOTE CONTROL  
SEARCH button  
22  
14  
STANDBY/ON button  
RGB button  
15  
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
VIDEO button  
AUTO button  
BLANK button  
15  
22  
19  
22  
ASPECT  
BLANK  
VOLUME  
ASPECT button  
HOME  
END  
PAGE UP  
MAGNIFY  
ON  
VOLUME button  
MUTE button  
17  
17  
20  
MAGNIFY buttons  
21  
PAGE DOWN  
MUTE  
OFF  
FREEZE  
KEYSTONE  
FREEZE button  
KEYBOARD buttons  
POSITION button  
KEYSTONE button  
21  
9
2
POSITION  
MENU  
18  
23  
23  
MENU button  
23  
ENTER  
,
,
,
Cursor buttons  
ESC  
RESET  
RESET button  
ENTER button  
9
2
ESC button  
23  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING UP THE PROJECTOR  
CAUTION Install the projector in a suitable environment according to instructions  
of the "Product Safety Guide" and this "Operator's Guide".  
If you press the elevator button without holding the projector, the projector might  
crash down, overturn, smash your fingers and possibly result in malfunction. To  
prevent damaging the projector and injuring yourself, ALWAYS HOLD THE  
PROJECTOR whenever using the elevator button to adjust the elevator foot.  
Adjusting the Projector's Elevator Foot  
You can use the elevator foot to make adjustments if the surface on which you  
need to set the projector is uneven or if you otherwise need to adjust the angle of  
projection. The adjustment range of the elevator foot is 0 to 9 degrees.  
Press and hold in the elevator  
button  
1
Raise or lower the projector to the  
2
desired height and then release the  
elevator button  
When you release the elevator button, the elevator  
foot will lock into position.  
As necessary, you can also finely  
3
adjust the left-right slope of the  
projector by twisting the rear foot  
adjuster screw by hand  
9
Rear Foot Adjuster  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Screen Size and Projection Distance  
Refer to the illustrations and tables below to determine the screen size and  
projection distance.  
The values shown in the table are calculated for a full size screen  
(S50: 800x600 pixels/X50: 1024x768 pixels).  
a:Distance from the projector to the screen ( 10%)  
b:Distance from the lens center to the bottom of the screen ( 10%)  
c:Distance from the lens center to the top of the screen ( 10%)  
The screen  
Top view  
If 4:3 aspect ratio  
4
3
a [inch (m)]  
Min. Max.  
b
c
Screen Size [inch (m)]  
[inch (cm)] [inch (cm)]  
30 (0.8)  
40 (1.0)  
50 (1.3)  
60 (1.5)  
70 (1.8)  
80 (2.0)  
90 (2.3)  
100 (2.5)  
120 (3.0)  
150 (3.8)  
200 (5.0)  
250 (6.3)  
300 (7.5)  
35 (0.9) 42 (1.1) 1 (2) 17 (44)  
47 (1.2) 56 (1.4) 1 (3) 23 (58)  
59 (1.5) 71 (1.8) 1 (4) 29 (73)  
71 (1.8) 85 (2.2) 2 (4) 34 (87)  
83 (2.1) 100 (2.5) 2 (5) 40 (102)  
95 (2.4) 114 (2.9) 2 (6) 46 (116)  
107 (2.7) 129 (3.3) 3 (7) 51 (131)  
119 (3.0) 143 (3.6) 3 (7) 57 (145)  
143 (3.6) 172 (4.4) 3 (9) 69 (174)  
180 (4.6) 216 (5.5) 4 (11) 86 (218)  
240 (6.1) 288 (7.3) 6 (15) 114 (290)  
300 (7.6) 361 (9.2) 7 (18) 143 (363)  
360 (9.2) 433 (11.0) 9 (22) 171 (435)  
Lens center  
c
Side view  
Top view  
b
a
The screen  
If 16:9 aspect ratio  
16  
9
a [inch (m)]  
Min. Max.  
b
c
Screen Size [inch (m)]  
[inch (cm)] [inch (cm)]  
30 (0.8)  
40 (1.0)  
50 (1.3)  
60 (1.5)  
70 (1.8)  
80 (2.0)  
90 (2.3)  
100 (2.5)  
120 (3.0)  
150 (3.8)  
200 (5.0)  
250 (6.3)  
300 (7.5)  
38 (1.0) 46 (1.2) 2 (4)  
51 (1.3) 61 (1.6) 2 (5)  
64 (1.6) 77 (2.0) 3 (6)  
77 (2.0) 93 (2.4) 3 (8)  
90 (2.3) 109 (2.8) 4 (9)  
104 (2.6) 125 (3.2) 4 (10) 43 (110)  
117 (3.0) 140 (3.6) 5 (12) 49 (124)  
130 (3.3) 156 (4.0) 5 (13) 54 (137)  
156 (4.0) 188 (4.8) 6 (15) 65 (165)  
196 (5.0) 235 (6.0) 8 (19) 81 (206)  
261 (6.6) 314 (8.0) 10 (26) 108 (275)  
327 (8.3) 393 (10.0) 13 (32) 135 (343)  
393 (10.0) 472 (12.0) 15 (39) 162 (412)  
16 (41)  
22 (55)  
27 (69)  
32 (82)  
38 (96)  
c
Lens center  
Side view  
b
a
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING YOUR DEVICES  
Devices You Can Connect to the Projector  
(Refer to this section for planning your device  
configuration to use for your presentation.)  
CAUTION Incorrect connecting could result in fire or electrical shock. Please  
read the "Product Safety Guide" and this "Operator's Guide".  
ATTENTION Precautions to observe when connecting other devices to the projector  
Whenever attempting to connect other devices to the projector, please thoroughly  
read the manual of each device to be connected.  
TURN OFF ALL DEVICES prior to connecting them to the projector. Attempting to  
connect a live device to the projector may generate extremely loud noises or other  
abnormalities that may result in malfunction and/or damage to the device and/or  
projector. Refer to the TECHNICALfor the pin assignment of connectors and  
RS-232C communication data.  
Make sure that you connect devices to the correct port. Incorrect connection may  
result in malfunction and/or damage to the device and/or projector.  
A component cable and some other cables have to be used with core set. Use the  
accessory cable or a designated-type cable for the connection. For cables that have  
a core only at one end, connect the core to the projector.  
Secure the screws on the connectors and tighten.  
Indicates the  
corresponding  
reference page  
Display monitors  
12  
DVD players  
11  
10 Laptop computers  
VCRs  
11  
Desktop computers  
10  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ports and Cables  
Refer to the table below to find out which projector port and cable to use for connecting a  
given device. Use this table for determining which cables to prepare.  
Function  
Projector Port  
Connection Cables  
rgb in 1  
Accessory RGB cable or optional RGB  
cable with D-sub 15-pin shrink jack and  
inch thread screws  
RGB input  
rgb in 2  
rgb out  
usb  
RGB output  
USB mouse control  
PS/2 mouse control  
ADB mouse control  
Serial mouse control  
RS-232C communication  
Accessory USB cable  
Optional PS/2 mouse cable  
Optional ADB mouse cable  
Optional serial mouse cable  
Optional RS-232C cable  
control  
Optional S-video cable with mini DIN 4-pin  
jack  
S-video input  
Video input  
s-video in  
video in  
Accessory audio/video cable  
component video Y  
component video CB/PB  
component video CR/PR  
audio in L  
Component video input  
Audio input  
Optional component video cable  
Accessory audio/video cable or optional  
audio cable with RCA jack  
audio in R  
NOTE  
About Plug-and-Play Capability  
This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved by  
connecting this projector to computers that are VESA DDC (display data channel)  
compatible. Please take advantage of this function by connecting the accessory RGB  
cable to the rgb in 1port (DDC 1/2B compatible). Plug-and-Play may not work  
properly if any other type of connection is attempted.  
Plug-and-Play is a system composed of the computer, its operating system and  
peripheral equipment (i.e. display devices).  
Please use the standard drivers as this projector is a Plug-and-Play monitor.  
Plug-and-Play may not function properly with some type of computers. Use the rgb in 2  
port if Plug-and-Play does not function correctly.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING YOUR DEVICES (continued)  
Connecting to a Computer  
ATTENTION Whenever attempting to connect a laptop computer to the projector,  
be sure to activate the laptop's RGB external image output (set the laptop to CRT  
display or to simultaneous LCD and CRT display). For details on how this is done,  
please refer to the instruction manual of the corresponding laptop computer.  
1
rgb in  
2
1
rgb in  
2
audio in  
L/ (mono) video in  
audio in  
L/ (mono) video in  
s-video in  
s-video in  
R
R
A
A
B B  
C C  
C
R/RR  
C
B/PB  
Y
C
R/RR  
C
B/PB  
Y
C
usb  
usb  
B
D
rgb out  
control  
rgb out  
control  
component viideo  
component viideo  
A
B
A
C
D
B
USB cable  
If connecting to a  
USB port equipped  
computer  
Laptop computer  
Desktop computer  
NOTE  
Some computers may have multiple display screen modes. Use of some of these  
modes will not be possible with this projector.  
For some RGB input modes, the optional Mac adapter is necessary.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a DVD Player  
1
rgb in  
2
audio in  
L/ (mono) video in  
s-video in  
R
C
B
B
B
Y
C
C
R/RR  
C
B/PB  
usb  
A
A
A
rgb out  
control  
component viideo  
A
B
C
S-VIDEO cable  
If using a S-video  
connection  
If using an audio/video  
connection  
If using a component  
video connection  
DVD player  
Connecting to a VCR  
1
rgb in  
2
audio in  
L/ (mono) video in  
s-video in  
R
B
A
A
A
Y
C
R/RR  
C
B/PB  
usb  
rgb out  
control  
component viideo  
A
B
S-VIDEO cable  
If using a S-video  
connection  
VCR  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING YOUR DEVICES (continued)  
Connecting to a Display Monitor  
1
rgb in  
2
audio in  
L/ (mono) video in  
s-video in  
R
C
R/RR  
C
B/PB  
Y
usb  
A
rgb out  
control  
component viideo  
A
Display monitor  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING THE REMOTE CONTROL  
Putting batteries into the remote control unit  
CAUTION Precautions to observe in regards to the batteries  
Always handle the batteries with care and use them only as directed. Improper use may result in  
battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.  
Keep the battery away from children and pets.  
Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.  
When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control).  
When you dispose the battery, you should obey the law in the relative area or country.  
Remove the battery  
cover  
Close the battery  
cover  
Insert the batteries  
Align and insert the two AA  
batteries (that came with the  
projector) according to their plus  
and minus terminals (as indicated  
in the remote control).  
1
2
3
Slide back and remove  
the battery cover in the  
direction of the arrow.  
Replace the battery cover  
in the direction of the arrow  
and snap it back into place.  
Operating the remote control  
The remote control works with both the  
projector's front and rear remote sensors.  
The range of the remote sensor on the front and  
back is 3 meters with a 60-degree range (30  
degrees to the left and right of the remote sensor).  
Since the remote control uses infrared light to send  
signals to the projector (Class 1 LED), be sure to  
approximately  
3 meters  
approximately  
3 meters  
use the remote control in an area free from  
obstacles that could block the remote control's  
output signal to the projector.  
ATTENTION  
Precautions to observe when using the remote control  
Do not drop or otherwise expose the remote control to physical impact.  
Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.  
Remove the batteries from the remote control and store them in a safe place if you  
won't be using the remote control for an extended period.  
Replace the batteries whenever the remote control starts to malfunction.  
When strong light, such as direct sunlight or light from an extremely close range (such as from an  
inverter fluorescent lamp), hits the projector's remote sensor, the remote control may cease to function.  
Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TURNING ON THE POWER  
Precautions  
8
12  
Connect all devices to be used to the projector prior to turning on the power.  
WARNING When the power is ON, a strong light is emitted. Do not look into the  
lens.  
Make sure that the power cord is firmly and  
correctly connected to the projector and outlet  
1
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
3
ASPECT  
BLANK  
VOLUME  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
Turn on the projector's power  
PAGE DOWN  
MUTE  
2
Set the power switch to [ | ] (ON). The projector will go  
to STANDBY mode and the powerindicator will light to  
OFF  
FREEZE  
KEYSTONE  
solid orange.  
power switch  
Control panel  
on off  
video  
rgb  
powerindicator  
reset  
lamp  
temp  
power  
keystone  
menu  
Press the STANDBY/ON button of the remote  
control or the on/off button of the control panel  
3
The projector begins warming up and the power indicator  
blinks green.  
The powerindicator stops blinking  
and lights to solid green once the  
projector's power is completely on.  
NOTE  
Turn the  
power on/off in  
right order.  
Power on the  
projector before the  
computer or video  
tape recorder.  
Power off the  
projector after the  
computer or video  
tape recorder.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting an Input Signal  
Selecting a RGB signal  
5
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
Press the RGB button of the remote control  
ASPECT  
BLANK  
VOLUME  
or the rgb button of the control panel  
Press this button to toggle between the devices  
connected to rgb in 1 and 2. As illustrated below, each  
time you press the RGB button or rgb button, the projector  
switches between rgb in 1 and 2. Select the signal you  
wish to project.  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
PAGE DOWN  
MUTE  
OFF  
FREEZE  
KEYSTONE  
RGB  
POSITION  
MENU  
rgb in 1  
rgb in 2  
ENTER  
ESC  
RESET  
Selecting a VIDEO signal  
Control panel  
Press the VIDEO button of the remote control  
or the video button of the control panel  
Press this button to toggle between the devices connected  
to video in, s-video in and component video. As illustrated  
below, each time you press the VIDEO button of the  
remote control or the video button of the control panel,  
the projector switches between video in, s-video in  
and component video. Select the signal you wish to  
project.  
on off  
video  
rgb  
reset  
lamp  
temp  
power  
keystone  
menu  
video in  
s-video in  
VIDEO  
component video  
Use the zoom ring to adjust the  
screen size  
6
7
Use the focus ring to focus the  
picture  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TURNING OFF THE POWER  
Press the STANDBY/ON button of the remote  
1
control or on/off button of the control panel  
The message "Power off?" will appear on the screen for approximately 5 seconds.  
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
ASPECT  
BLANK  
VOLUME  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
PAGE DOWN  
MUTE  
OFF  
Press the STANDBY/ON button or the on/off  
button again  
FREEZE  
KEYSTONE  
2
Press the STANDBY/ON button or on/off button again while the  
"Power off?" message is visible. The projector lamp goes off and  
starts cooling down. The power indicator blinks orange while the  
lamp cools down. (Pressing the STANDBY/ON button while the  
power indicator is blinking orange has no effect.)  
POSITION  
MENU  
ENTER  
ESC  
RESET  
The system goes into the STANDBY mode after cooling  
down and the power indicator stops blinking orange and  
then lights to solid orange.  
Control panel  
on off  
video  
rgb  
Check that the power indicator stops  
blinking and lights to solid orange.  
Switch the power switch to [O] (OFF).  
reset  
3
lamp  
temp  
power  
keystone  
menu  
When the projector has  
power switch  
completed powering down,  
the power indicator will go off.  
POWER indicator  
NOTE  
Except in  
emergencies, follow  
the above-  
mentioned  
procedure for  
turning power off.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADJUSTING THE VOLUME  
VOLUME  
Press the VOLUME button  
1
As illustrated on the right, a dialog will  
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
appear on the screen to aid you in adjusting  
the volume.  
ASPECT  
BLANK  
VOLUME  
VOLUME  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
PAGE DOWN  
MUTE  
16  
OFF  
FREEZE  
KEYSTONE  
Press the  
,
buttons to adjust  
2
POSITION  
MENU  
the volume  
Press the VOLUME button again to close the dialog and  
complete this operation. (Even if you don't do anything, the  
dialog will automatically disappear after a few seconds.)  
ENTER  
ESC  
RESET  
VOLUME  
Press this to increase the volume  
Press this to decrease the volume  
16  
TEMPORARILY MUTING THE SOUND  
Press the MUTE button  
1
STANDBY/ON  
As illustrated on the right, a dialog will appear on the  
screen indicating that you have muted the sound. Press  
the VOLUME button to close the dialog. (Even if you don't  
do anything, the dialog will automatically disappear after  
a few seconds.)  
VIDEO  
RGB  
SEARCH  
AUTO  
ASPECT  
BLANK  
VOLUME  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
PAGE DOWN  
MUTE  
OFF  
Press the MUTE button again to restore the sound.  
FREEZE  
KEYSTONE  
VOLUME  
MUTE  
POSITION  
MENU  
ENTER  
ESC  
RESET  
16  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADJUSTING THE POSITION  
Press the POSITION button  
1
As illustrated on the right, a dialog will appear on the screen  
to aid you in adjusting the position.  
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
ASPECT  
BLANK  
VOLUME  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
PAGE DOWN  
MUTE  
POSITION  
OFF  
FREEZE  
KEYSTONE  
POSITION  
POSITION  
MENU  
ENTER  
Use the  
,
,
,
buttons to adjust  
2
ESC  
RESET  
the position  
When you want to initialize the position, press the RESET  
button during adjustment.  
Press the POSITION button again to close the dialog and  
complete this operation. (Even if you don't do anything, the  
dialog will automatically disappear after a few seconds.)  
This function is only available for rgb in 1/2 input.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING THE AUTOMATIC ADJUSTMENT FEATURE  
Press the AUTO button  
1
AUTO  
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
ASPECT  
BLANK  
VOLUME  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
Automatic Adjustment for RGB Input  
Horizontal position (H. POSIT), vertical position (V.  
POSIT), clock phase (H. PHASE) and horizontal size (H.  
SIZE) are automatically adjusted.  
PAGE DOWN  
MUTE  
OFF  
FREEZE  
KEYSTONE  
Make sure that the application window is set to its  
maximum size prior to attempting to use this feature.  
Dark pictures may still be incorrectly adjusted. Use a  
bright screen when adjusting.  
POSITION  
MENU  
ENTER  
ESC  
RESET  
Automatic Adjustment for Video Input  
The signal type best suited for the respective input  
signal is selected automatically.  
This feature is available only if VIDEO is set to AUTO in  
the INPUT menu.  
NOTE  
The automatic adjustment operation requires approximately 10 seconds. Also, please  
note that it may not function correctly with some input signals.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CORRECTING KEYSTONE DISTORTIONS  
Press the KEYSTONE button  
KEYSTONE  
1
As illustrated on the right, a dialog will appear  
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
on the screen to aid you in correcting the  
distortion.  
ASPECT  
BLANK  
VOLUME  
KEYSTONE  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
PAGE DOWN  
MUTE  
OFF  
16  
FREEZE  
KEYSTONE  
POSITION  
MENU  
Use the  
,
buttons to select the  
2
3
direction of distortion to correct (  
/
)
ENTER  
ESC  
RESET  
Use the  
distortion  
,
buttons to correct the  
Press the KEYSTONE button again to close the dialog and  
complete this operation. (Even if you don't do anything, the  
dialog will automatically disappear after a few seconds.)  
NOTE  
This function may not be work well with some types of input signals.  
The adjustable range for correcting keystone distortions will vary with the type of  
input signal.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING THE MAGNIFY FEATURE  
Press the MAGNIFY (ON) button  
MAGNIFY  
1
The projector enters MAGNIFY mode.  
ON  
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
ASPECT  
BLANK  
VOLUME  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
Press the POSITION button, then use the  
,
,
2
PAGE DOWN  
MUTE  
,
buttons to select the area to enlarge and then  
OFF  
press the POSITION button again to confirm your  
selection  
FREEZE  
KEYSTONE  
POSITION  
POSITION  
POSITION  
MENU  
ENTER  
ESC  
RESET  
Press the  
,
buttons to zoom in and  
3
out of the selected area.  
Press the MAGNIFY (OFF) button to exit MAGNIFY mode  
and restore the screen to normal. (The projector will also  
automatically exit MAGNIFY mode if there is a change in the  
input signal's state.)  
NOTE  
The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,  
AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state.  
FREEZING THE SCREEN  
Press the FREEZE button  
MAGNIFY  
ON  
HOME  
PAGE UP  
VOLUME  
1
FREEZE  
The [II] icon appears and the screen will freeze at  
the current image. Press the FREEZE button again  
and the [ ] appears as the projector exits FREEZE  
mode.  
END  
PAGE DOWN  
MUTE  
OFF  
FREEZE  
KEYSTONE  
POSITION  
MENU  
NOTE  
The projector will automatically exit from FREEZE mode if either the POSITION, VOLUME, MUTE, AUTO,  
BLANK ON/OFF or MENU ON/OFF feature is used, or, if there is a change in the input signal's state.  
If the projector continues projecting the same image for a long time (i.e. you forget to exit FREEZE mode),  
the image might possibly remain as an afterimage. Do not leave the projector in FREEZE mode for too long.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIGNAL SEARCHING  
Press the SEARCH button  
1
When you press the SEARCH button, the projector begins  
searching for input signals. If it detects an input signal, the  
search will cease and the projector will project the detected  
signal. If the projector is unable to find an input signal at any of  
its ports, it will return to the state it was in prior to the search.  
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
ASPECT  
BLANK  
VOLUME  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
PAGE DOWN  
MUTE  
OFF  
SEARCH  
rgb in 1  
rgb in 2  
video in  
FREEZE  
KEYSTONE  
s-video in  
component video  
SELECTING THE ASPECT RATIO  
Press the ASPECT button  
1
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
ASPECT  
ASPECT  
BLANK  
VOLUME  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
PAGE DOWN  
MUTE  
rgb in 1, rgb in 2, component video  
(HDTV signals : 1125i (1035i/1080i), 750p)  
OFF  
FREEZE  
KEYSTONE  
4:3  
16:9  
video in s-video in, component video  
POSITION  
MENU  
(Non-HDTV signals : 525i, 525p,625i)  
ENTER  
4:3  
16:9  
SMALL  
ESC  
RESET  
TEMPORARILY BLANKING THE SCREEN  
Press the BLANK button  
1
The input signal screen is shut off, and a blank screen  
appears. You can set the blank screen using the menu  
(from the SCREEN menu, select BLANK). Press the BLANK  
button again to remove the blank screen, and return to the  
input signal screen.  
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
ASPECT  
BLANK  
VOLUME  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
PAGE DOWN  
MUTE  
OFF  
FREEZE  
KEYSTONE  
BLANK  
POSITION  
MENU  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING THE MENU FUNCTIONS  
MENU  
Press the MENU button  
1
The menu display appears on the screen. The  
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
projector has the following menus: MAIN,  
PICTURE-1, PICTURE-2, INPUT, SCREEN, and  
ASPECT  
BLANK  
VOLUME  
OPTION. Select a menu using the  
/
buttons. The  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
current settings of the items that can be manipulated via the  
selected menu appear.  
PAGE DOWN  
MUTE  
OFF  
FREEZE  
KEYSTONE  
/
Select a menu using the  
buttons,  
2
then press the  
or ENTER button.  
POSITION  
MENU  
The display of the selected menu appears.  
ENTER  
[ex. Adjusting SHARPNESS]  
Use the  
the  
/
buttons to select PICTURE-1, then press  
ESC  
RESET  
or ENTER button.  
MENU  
MAIN  
COLOR BAL R  
COLOR BAL B  
SHARPNESS  
COLOR  
1  
+1  
1  
+1  
1  
PICTURE-1  
PICTURE-2  
INPUT  
SCREEN  
OPTION  
TINT  
ENTER  
: SELECT  
/
Select an item using the  
or ENTER button.  
buttons, then press the  
3
The operation display of the selected item appears. To adjust a numerical value,  
press the  
or ENTER button again to switch to the single menu (small display  
showing only the operation display area).  
[ex. Adjusting SHARPNESS]  
Use the  
press the  
/
buttons to select SHARPNESS, then  
or ENTER button.  
MENU  
MAIN  
COLOR BAL R  
COLOR BAL B  
SHARPNESS  
COLOR  
PICTURE-1  
PICTURE-2  
INPUT  
SCREEN  
OPTION  
TINT  
ENTER  
0
: SELECT  
/
Press the  
buttons to adjust the level.  
4
Press the MENU button to hide the menu and finish your operation. Alternatively,  
press the  
[ex. Adjusting SHARPNESS]  
Use the buttons to adjust the SHARPNESS.  
or ESC button to return to the previous display.  
/
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MULTIFUNCTIONAL SETTINGS  
This device has 6 separate menus: MAIN, PICTURE 1, PICTURE 2, INPUT,  
SCREEN, OPTION. Each of these menus is operated using the same methods.  
The basic operations of these menus are as follows.  
Menu screen display : Press the "MENU" button.  
Menu selection  
: Choose a menu name using the  
/
button, and press the  
button or the ENTER button.  
Item selection  
: Choose an item using the  
button or the ENTER button.  
/
button, and press the  
Return menu to last previous screen: Press the  
button or the ESC button.  
Execution of settings and/or adjustments Operate by using the  
:
/
button. (For further  
details, read the explanation for each separate menu.)  
I
nitialization of settings and/or adjustments: During operation, press the RESET button.  
(Note that items whose functions are  
performed simultaneously with the operation  
of clock phase, language selection, automatic  
adjustment, etc., cannot be initialized.)  
End menu operations: Press the MENU button, or do not perform any operation for  
several seconds.  
MENU  
MAIN  
BRIGHT  
CONTRAST  
ASPECT  
PICT. POSIT.  
GAMMA  
MIRROR  
MAIN Menu  
With the MAIN menu, the seven items shown in the Table below can be  
performed.  
PICTURE-1  
PICTURE-2  
INPUT  
SCREEN  
OPTION  
LANGUAGE  
12  
Perform each operation in accordance with the instructions in the Table.  
: SELECT  
Example : MAIN Menu  
(BRIGHT)  
MAIN Menu  
Item  
Description  
BRIGHT  
Adjust Brightness: Light  
Dark  
CONTRAST  
Adjust Contrast: Strong  
Weak  
Select Aspect Ratio:  
At rgb Input or Hi-Vision 1125i(1035i/1080i)/750p of component video  
Input:  
ASPECT  
4:3  
At video Input, s-video Input or 525i/525p/625i of component video Input:  
4:3 16:9 SMALL  
16:9  
• The SMALL picture may not be displayed correctly with certain input signals.  
Select Picture Position (for 16:9/SMALL Picture):  
PICT.POSIT.  
GAMMA  
TOP  
CENTER  
BOTTOM  
DYNAMIC  
V:INVERT  
Select Gamma Mode:  
NORMAL CINEMA  
Select Mirror Status:  
NORMAL H:INVERT  
MIRROR  
H&V:INVERT  
Select Menu Language:  
ENGLISH  
FRANÇAIS  
DEUTSCH  
ESPAÑOL  
LANGUAGE  
ITALIANO  
NORSK  
NEDERLANDS  
日本語  
POTUGUÊS  
中文  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
MAIN  
COLOR BAL R  
COLOR BAL B  
SHARPNESS  
COLOR  
PICTURE 1 Menu  
PICTURE-1  
PICTURE-2  
INPUT  
SCREEN  
OPTION  
TINT  
With the PICTURE 1 menu, the five items shown in the Table  
below can be performed.  
Perform each operation in accordance with the instructions in the  
Table.  
12  
: SELECT  
Example : PICTURE1 Menu  
(COLOR BAL R)  
PICTURE1 Menu  
Item  
Description  
Adjust Red Color Balance: Dark  
Adjust Blue Color Balance: Dark  
Adjust Sharpness (for video/s-video): Clear  
COLOR BAL R  
Light  
COLOR BAL B  
SHARPNESS  
Light  
Soft  
Adjust COLOR (for video/s-video/component video):  
Dark Light  
COLOR  
TINT  
Adjust Tint (for video/s-video): Green  
Red  
MENU  
MAIN  
V POSITION  
H POSITION  
H PHASE  
PICTURE 2 Menu  
PICTURE-1  
PICTURE-2  
INPUT  
H SIZE  
SCREEN  
OPTION  
OVER SCAN  
With the PICTURE 2 menu, the five items shown in the Table  
below can be performed.  
Perform each operation in accordance with the instructions in the  
Table.  
12  
: SELECT  
Example : PICTURE2 Menu  
(V POSITION)  
PICTURE2 Menu  
Item  
Description  
Adjust Vertical Position (for rgb): Up  
Adjust Horizontal Position (for rgb): Left  
Adjust Horizontal Phase (for rgb/component video):  
V POSITION  
H POSITION  
Down  
Right  
H PHASE  
H SIZE  
Right Left  
• Adjust to eliminate flicker.  
Adjust Horizontal Size (for rgb): Large  
• If the horizontal size adjustment is excessive, the image may not be displayed  
correctly. In such a case, initialize H SIZE with the RESET button.  
Small  
Select Over-scan Ratio (for video/s-video/component video):  
LARGE  
MIDDLE  
SMALL  
OVER SCAN  
• It is recommended to select SMALL to avoid flicker at the lower part of the  
picture.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MULTIFUNCTIONAL SETTINGS (continued)  
MENU  
MAIN  
PICTURE-1  
PICTURE-2  
INPUT  
AUTO  
VIDEO  
HDTV  
SYNC ON G  
EXECUTE  
INPUT Menu  
SCREEN  
OPTION  
With the INPUT menu, the four items shown in the Table below can be  
performed. With inputting of rgb in 1 and rgb in 2 signals, the  
horizontal and vertical frequencies of the signals will be displayed on the  
: SELECT  
Example : INPUT Menu  
(AUTO)  
initial screen of the INPUT menu.  
Perform each operation in accordance with the instructions in the Table.  
INPUT Menu  
Item  
Description  
Auto Adjust (for rgb): Automatically adjusts H POSITION, V POSITION, H  
PHASE, and H SIZE. Use this function with the maximum window size.  
Auto Adjust (for video/s-video): Automatically selects the proper VIDEO  
mode for the current input signal. This function is active only when the AUTO  
mode is selected for the item VIDEO. Refer to the description for the item  
VIDEO below.  
AUTO  
• This function may not be available with a PAL60 signal and certain other  
signals.  
• The AUTO mode operation requires approximately 10 seconds.  
• For component video, the signal type is identified automatically even if this  
function is inactive. For a HDTV signal, refer to the item HDTV below.  
Select Mode of Signal Type (for video/s-video):  
AUTO  
NTSC  
M-PAL  
PAL  
SECAM  
NTSC4.43  
N-PAL  
Selecting AUTO mode activates and performs the AUTO function for video/s-  
video. It automatically selects the proper mode from among those above.  
Use this function if the image becomes unstable with video/s-video. (e.g.  
The image becomes irregular, or lacks color.)  
VIDEO  
• AUTO mode may not function correctly with a PAL60 signal and certain other  
signals.  
• The AUTO mode operation requires approximately 10 seconds.  
For component video, the signal type is identified automatically even if  
this function is inactive. For a HDTV signal, refer to the item HDTV below.  
Select HDTV Signal Mode:  
1080i 1035i  
HDTV  
• If the selected HDTV mode is incompatible with the input signal, the picture  
may be distorted.  
On/Off SYNC ON G Mode:  
TURN ON  
TURN OFF  
Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode  
allows reception of SYNC on G.  
SYNC ON G  
• In the SYNC ON G mode, the picture may be distorted with certain input  
signals. In such a case, remove the signal connector so that no signal is  
received and turn SYNC ON G off, and then reconnect the signal.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU  
MAIN  
BLANK  
START UP  
MyScreen  
MyScreen Size  
MyScreen Lock  
MyScreen  
ORIGNAL  
SCREEN Menu  
PICTURE-1  
PICTURE-2  
INPUT  
SCREEN  
OPTION  
With the SCREEN menu, the five items shown in the Table below can be performed.  
Please perform each operation in accordance with the instructions in the Table.  
: SELECT  
Example : SCREEN Menu  
(BLANK)  
SCREEN Menu  
Item  
Description  
Selection of BLANK Screen:  
MyScreen  
ORIGINAL  
.
.
.
.
.
.
The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen  
has been erased (i.e., made to vanish) by manipulating the BLANK button (please refer to the  
Temporarily Blanking the Screen” section).  
BLANK  
MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen  
(or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen.  
ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s).  
Option screens: Various colored non-patterned (plain) screens displayed within the Menus.  
• The MyScreen and the ORIGINAL Screen will each change to a non-patterned (plain) black color  
screen several minutes after being displayed.  
Selection of START UP Screen:  
MyScreen  
ORIGINAL  
TURN OFF  
The START UP Screen may be voluntarily selected. The START UP Screen is displayed when  
no signal has been inputted, or when spec signals are being inputted.  
MyScreen: Using the MyScreen category (see this Table, below), one can register a  
desired screen (or screens). At the time of factory shipment, this is set as a non-patterned  
(plain) blue color screen.  
START UP  
ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s).  
TURN OFF: A non-patterned (plain) blue color screen.  
The MyScreen and the ORIGINAL Screen will each change to the BLANK Screen several  
minutes after being displayed.  
Registration of MyScreen:  
When this item is executed, the MyScreen Menu for registration of MyScreen for the BLANK Screen  
and the START UP Screen is displayed. When operations are performed in accordance with this Menu,  
one can “cut” and register desired screens from among the received images within the display.  
1. After the “Do you start capturing this picture?” message has been displayed, pressing the ESC (or  
RESET) button interrupts execution of the MyScreen. When the ENTER button is pressed, the  
picture becomes static (no longer moves), and a frame for picture cutting, as well as the message  
that follows below, appear. Please press the button when the screen you want to register is  
currently being displayed.  
MyScreen  
2. When the “Move the capture area as you want.” message has been displayed, pressing the ESC (or RESET)  
button will eliminate the static state of the picture, and operations can be performed again from operation 1.  
The frame can be moved using the  
,
,
,
buttons. After designating the screen  
you want to register, pressing the ENTER button will initiate screen registration. The registration  
process takes approximately 1 minute to complete.  
3. When the registration has been completed, the screen of the registered MyScreen, plus the  
message, “MyScreen registration is finished,” will be displayed for several seconds, after which  
the operation is terminated.  
Selection of MyScreen display size:  
MyScreen Size  
MyScreen Lock  
x1  
FULL  
Invalidation of MyScreen registration function:  
TURN ON  
TURN OFF  
When TURN ON is selected, the MyScreen category (see this Table, above) cannot be executed; in  
this way, one can prohibit rewrites (“writeovers”) of the MyScreen.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MULTIFUNCTIONAL SETTINGS (continued)  
MENU  
MAIN  
PICTURE-1  
PICTURE-2  
INPUT  
SCREEN  
OPTION  
VOLUME  
OPTION Menu  
AUTO OFF  
WHISPER  
LAMP TIME  
FILTER TIME  
With the OPTION menu, the five items shown in the Table below  
can be performed.  
Please perform each operation in accordance with the instructions  
in the Table.  
12  
: SELECT  
Example : OPTION Menu  
(VOLUME)  
OPTION Menu  
Item  
Description  
VOLUME  
Adjust Volume: High  
Low  
Adjust AUTO OFF Time:  
Long (MAX. 99 min.)  
Short (Min. 1 min.)  
(DISABLE: 0 min.)  
AUTO OFF  
WHISPER  
The system automatically enters the standby mode if no signal is received  
within the set time. This function is inactive when DISABLE (0 min.) is selected.  
Select WHISPER Mode:  
NORMAL  
WHISPER  
When WHISPER is selected the WHISPER mode is activated. In the WHISPER  
mode, acoustic noise and screen brightness are reduced.  
Refer to LAMP TIME: When set, this function displays the total time the  
projector lamp has been used since new.  
Reset LAMP TIME [Use this function only when the lamp has been replaced!]:  
Depress the RESET button for at least 3 seconds while lamp time is being  
displayed. The reset menu will then appear. After you replace the lamp with a  
LAMP TIME  
new lamp, select RESET on the menu with the  
button.  
• Do not reset the lamp time unless you have replaced the lamp. And, always  
reset the lamp time when replacing the lamp. The message functions will not  
operate properly if the lamp time is not reset correctly.  
• Before replacing the lamp, carefully read the descriptions headed "THE  
LAMP".  
Refer to FILTER TIME: This function displays the total time the air-filter has  
been used since new.  
Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]:  
Depress the RESET button for at least 3 seconds while filter time is being  
displayed. The reset menu will then appear. After you replace the filter, select  
FILTER TIME  
RESET on the menu with the  
DEFAULT CANCEL  
button.  
• Do not reset the filter time unless you have cleaned or replaced the filter. And,  
always reset the filter time when cleaning or replacing the filter. The message  
functions will not operate properly if the filter time is not reset correctly.  
Before cleaning or replacing the filter, carefully read the descriptions headed "THE AIR FILTER".  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING THE PC SCREEN  
You can use the remote control as a simplified mouse or keyboard.  
CAUTION Caution: Mistaken use of the mouse/keyboard control could damage your equipment.  
Only connect to a PC.  
Before connecting, read the manuals of the device you will connect.  
Do not unplug the connector cables while the computer is operating.  
PS/2, ADB, Serial Mouse Control  
STANDBY/ON  
VIDEO  
RGB  
SEARCH  
AUTO  
1. Turn off the projector and PC power, and connect the projectors  
control terminal to the computer via the mouse cable.  
2. If a USB cable is connected, disconnect it. If a USB cable is connected, the USB control  
function is given priority, and mouse control from the control terminal will not function.  
3. Turn on the projector power, then the computer.  
ASPECT  
BLANK  
VOLUME  
MAGNIFY  
ON  
HOME  
END  
PAGE UP  
PAGE DOWN  
MUTE  
The functions in the table below can be controlled. If you have difficulty with control,  
restart the computer (either from the software or by pressing the restart button).  
OFF  
FREEZE  
KEYSTONE  
Available Functions  
Remote Control Operation  
Move Pointer  
Use  
buttons  
POSITION  
MENU  
Left click with mouse  
Right click with mouse  
Press ENTER button  
Press RESET button  
ENTER  
ESC  
RESET  
USB Mouse/Keyboard Control  
1. Connect the projectors USB terminal to the computer using a USB cable.  
The functions in the table below can be controlled.  
Available Functions  
Remote Control Operation  
Move Pointer  
Use  
buttons  
Left click with mouse  
Press ENTER button  
Press RESET button  
Press HOME button  
Press END button  
Right click with mouse  
Press keyboards HOME key  
Press keyboards END key  
Press keyboards PAGE UP key  
Press keyboards PAGE DOWN key  
Press keyboards ESC key  
Press PAGE UP button  
Press PAGE DOWN button  
Press ESC button  
NOTES  
It may not be possible to control notebook PCs, and other computers with built-in pointing devices (e.g.  
track balls), using this remote control. In this case, before connecting go into BIOS (system setup) and  
select external mouse, and disable the pointing devices. In addition, the mouse may not function if the  
computer does not have the needed utility program. See your computers hardware manual for details.  
The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to  
use the remote control, depending on the computers configurations and mouse drivers.  
The USB control can only be used for the functions listed above. You cannot do things like press two buttons  
at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).  
This function is not available while the lamp is warming up (the power indicator flashes green), while adjusting the volume and  
display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu screen.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THE LAMP  
HIGH VOLTAGE  
HIGH TEMPERATURE  
HIGH PRESSURE  
Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately:  
78-6969-9599-8), then contact your local dealer.  
Before replacing the lamp, turn off the power, and unplug the power cord, then  
WARNING  
wait at least 45 minutes, in order to ensure that the lamp is properly cooled.  
Removing the lamp bulb while it is still hot could cause burns, or cause the lamp bulb to burst.  
The LCD projector uses a glass lamp bulb. It is a mercury lamp with high  
WARNING  
internal pressure. High-pressure mercury lamps can break with a loud  
bang, or burn out, if jolted or scratched, or through wear over time. Each lamp has a  
different lifetime, and some may burst or burn out soon after you start using them. In  
addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing,  
and for gas containing mercury to escape from the projectors vent holes.  
Handle with care: jolting or scratching could cause the lamp bulb to burst during use.  
35  
If the replace lamp indicator (see "Related Messages" (  
) and "Regarding the indicator  
36  
Lamps" (  
)) comes on, replace the lamp as soon as possible. Using the lamp for long  
periods of time, or past the replacement date, could cause it to burst. Do not use old  
(used) lamps; this is a cause of breakage.  
If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems  
elsewhere besides the lamp. If this happens, contact your local dealer.  
If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make  
sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.  
If the lamp should break (it will make a loud bang when it does), unplug the power cord from  
the outlet, and make sure to request a replacement lamp from your local dealer. Note that  
shards of glass could damage the projectors internals, or cause injury during handling, so  
please do not try to clean the projector or replace the lamp yourself.  
Obey local ordinances when disposing of used lamps. In most cases, it is possible to dispose of used  
bulbs in the same manner as used glass bottles, but in some cases, bulbs are sorted separately.  
Do not use the projector with the lamp door removed.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THE LAMP (continued)  
Replacing the lamp  
All projector lamps will wear out eventually. If used for long periods of time, the image could become  
darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps  
early. If the lamp indicator turns red, or a message prompts you to replace the lamp when you power up  
the projector, the lamp needs to be replaced. (See "Related Messages" (  
5
) and "Regarding the  
3
36  
Indicator Lamps" (  
) for details.)  
Turn off the projector, and unplug the  
power cord. Allow the lamp bulb to cool  
for at least 45 minutes, and prepare a  
new lamp (sold separately:  
Insert the new lamp, and tighten the 1  
screw firmly to lock it in place  
1
5
Also steadily push the opposite side of the  
screwed side of the  
lamp into the unit.  
78-6969-9599-8).  
After making sure that the projector has  
cooled adequately, slowly flip over the  
projector, so that the bottom is facing up  
2
3
Replace the lamp door, and tighten  
the 2 screws firmly to lock it in  
place  
Unscrew the 2  
screws, and  
remove the  
lamp door  
6
Unscrew the 1 screw, and slowly pull  
out the lamp by the handle  
4
Slowly turn the projector so that  
the top is facing up  
Be careful not to touch the inside of the lamp case.  
7
8
Turn on the projector power, and using  
the menu, reset the lamp timer  
To reset the lamp timer, from the OPTION  
menu, select LAMP TIME.  
ATTENTION Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.  
Do not use with lamp door removed.  
Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing  
the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.  
When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER  
WILL TURN OFF AFTER 0 hr." is displayed, or the lamp indicator is red, complete the following  
operation within 10 minutes of switching power ON.  
NOTE  
The lamp indicator is also red when the lamp unit reaches high temperature.  
Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power  
ON again. If the lamp indicator is still red, replace the lamp.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THE AIR FILTER  
Caring for the air filter  
The air filter should be cleaned about every 100 hours. If the lamp indicator and  
temp indicator blink red simultaneously, or a message prompts you to clean the air  
filter when you turn on the unit, the filter needs to be cleaned. (See "Related  
35  
36  
Messages" (  
) and "Regarding the Indicator Lamps" (  
) for details.)  
Turn off the projector, and unplug the power cord  
1
2
After making sure that the  
projector hascooled adequately,  
slowly flip over the projector, so  
that the bottom is facing up  
Remove the air filter  
Clean the air filter and  
3
4
Air Filter  
ventilation openings  
Ventilation  
openings  
with a vacuum cleaner  
Insert the air filter  
5
6
7
Slowly turn the projector so that the top is facing up  
Turn on the projector, and use the menu to reset the filter  
timer  
To reset the air filter timer, from the OPTION menu, select FILTER TIME.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THE AIR FILTER (continued)  
Replacing the air filter  
If the soiling will not come off the air filter, or it becomes damaged, then it needs to be  
replaced. Please contact your local dealer, after confirming the model of your  
separately sold replacement air filter.  
Turn off the projector, and unplug the power cord. Prepare a  
new air filter (one specified for your projector)  
1
After making sure that the  
2
projector has cooled adequately,  
slowly flip over the projector,  
so that the bottom is facing up  
Remove the air filter  
3
Air Filter  
Insert the new filter  
4
Slowly turn the projector so that the top is facing up  
5
Turn on the projector power, and using the menu, reset the  
6
filter timer  
To reset the air filter timer, from the OPTION menu, select FILTER TIME.  
Make sure to turn off the power and unplug the power cord before caring for  
WARNING  
the unit. Please carefully read "Product Safety Guide", in order to care for your projector correctly.  
Do not use with air filter cover removed.  
If the air filter becomes clogged by dust or the like, internal temperature rises and could cause  
malfunction. The power is automatically turned off in order to prevent the unit from overheating  
internally.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OTHER CARE  
Caring for the inside of the projector :  
In order to ensure the safe use of your projector, please have it cleaned and inspected by  
your local dealer about once every 2 years. Never try to care for the inside of the unit  
yourself. Doing so is dangerous.  
Caring for the lens :  
Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the  
lens directly with your hand.  
Caring for the cabinet and remote control transmitter :  
Wipe lightly with gauze or a soft cloth. If soiling is severe, dip a soft cloth in water or a  
neutral cleanser diluted in water, and wipe lightly after wringing well. Then, wipe lightly  
with a soft, dry cloth.  
WARNING  
Make sure to turn off the power and unplug the power cord before caring  
for the unit. Please carefully read "Product Safety Guide", in order to care for your projector  
correctly.  
Do not use cleaners or chemicals other than those listed above, including benzene and paint  
thinner.  
Do not use aerosols or sprays.  
Do not polish or wipe with hard objects.  
NOTE  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED  
Related Messages  
When the unit's power is ON, messages such as those shown below may be displayed. When  
any such message is displayed on the screen, please respond as described below.  
Message  
Description  
CHANGE THE LAMP  
Lamp usage time is approaching 2,000 hours. (Note 2)  
Preparation of a new lamp, and an early lamp change, is  
recommended. After you have changed the lamp, please be  
sure to reset the lamp timer.  
AFTER REPLACING LAMP,  
RESET THE LAMP TIMER.  
(Note 1)  
Lamp usage time is approaching 2,000 hours. A lamp change  
within ** hours is recommended. (Note 2)  
When lamp usage reaches 2,000 hours, the power will  
automatically be turned OFF. Please change the lamp  
by referring to “THE LAMP”. After you have  
changed the lamp, please be sure to reset the lamp  
timer.  
CHANGE THE LAMP  
AFTER REPLACING LAMP,  
RESET THE LAMP TIMER.  
THE POWER WILL TURN OFF  
AFTER ** hr.  
(Note 1)  
As lamp use has reached 2,000 hours, the power will soon be  
automatically turned OFF. (Note 2)  
CHANGE THE LAMP  
Please immediately turn the power OFF, and follow the  
instructions in the “THE LAMP”.  
AFTER REPLACING LAMP,  
RESET THE LAMP TIMER.  
After you have changed the lamp, please be sure to reset the  
lamp timer.  
THE POWER WILL TURN OFF  
AFTER 0 hr.  
A note of precaution when cleaning the air filter.  
After cleaning the filter, operate FILTER TIME of the OPTION  
Menu, and perform reset of the filter timer.  
CLEAN THE AIR FILTER  
AFTER CLEANING AIR FILTER,  
RESET THE FILTER TIMER.  
There is no input signal.  
Please confirm the signal input connection, and the status of the  
signal source.  
NO INPUT IS DETECTED  
ON ***  
The horizontal or vertical wavelength of the inputted signal is  
outside of the response parameters of this unit. Please confirm  
the specs for this unit or the signal source specs.  
SYNC IS OUT OF RANGE  
fH  
fV  
ON **  
***** kHz  
***** Hz  
The internal portion temperature is rising. Please turn the power  
OFF, and allow the unit to cool down for approximately 20  
minutes. After having confirmed the following items, then please  
resent the power to ON.  
CHECK THE AIR FLOW  
Is there blockage of the air passage aperture?  
Is the air filter dirty?  
Does the peripheral temperature exceed 35°C?  
NOTES  
Note 1: Although this message will be automatically disappeared after around 3 minutes, it will be  
reappeared every time the power is turned ON.  
Note 2: Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of  
usage, a lamp will no longer light up, or the lamp will break or burst, etc. This unit is equipped  
with an automatic shut-down function, such that the power will automatically be turned OFF  
when lamp usage time has reached 2,000 hours. Please be aware, however, that among lamp  
types, there are major differences in product lifetimes; a lamp may thus fail to light even prior  
to the functioning of the automatic shut-down function of this unit.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regarding the Indicator Lamps  
Lighting and flashing of the power indicator, the lamp indicator, and the temp indicator  
have the meanings as described in the Table below.  
Please respond in accordance with the instructions within the Table.  
power  
lamp  
temp  
Description  
indicator indicator indicator  
The orange  
Turned OFF Turned OFF  
The STANDBY mode is set  
lamp is lighted (Not lighted) (Not lighted)  
Flashing of the green lamp  
The green lamp is lighted  
Flashing of the orange lamp  
Turned OFF  
Turned OFF  
Turned OFF  
Turned OFF  
Turned OFF  
Turned OFF  
The unit is warming up. Please wait.  
The unit is in an ON state. Ordinary operations may be performed.  
The unit is cooling down. Please wait.  
The unit is cooling down. Please wait.  
Blinking of the  
red lamp  
A certain error has been detected. Wait until the power indicator lamp has finished  
flashing, and then perform the proper response measure using the item descriptions  
below as reference.  
-
-
The lamp does not light.  
There is a possibility that the interior portion has become heated. Turn the power OFF and wait  
approximately 20 minutes. After the main unit has cooled down, please confirm whether or not  
there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or  
not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,  
turn the power ON again; if the same display is displayed, then please change the lamp.  
The red lamp  
is lighted, or  
blinks  
The red lamp  
is lighted  
Turned  
OFF  
Either there is no lamp and/or lamp door, or either of these has not been properly fixed  
(attached). Turn the power OFF and wait approximately 45 minutes. After the main unit has  
sufficiently cooled down, please make confirmation of the attachment state of the lamp and  
lamp door. After performing any needed maintenance, turn the power ON again; if the same  
display is displayed, then please contact a sales store or a service company.  
The red lamp  
is lighted, or  
blinks  
Blinking of the  
red lamp  
Turned  
OFF  
The cooling fan is not operating. Turn the power OFF and wait approximately 20 minutes. After the  
main unit has cooled down, please make confirmation that no foreign matter has become caught in  
the fan, etc. After performing any needed maintenance, turn the power ON again; if the same display  
is displayed, then please contact a sales store or a service company.  
The red lamp  
is lighted, or  
blinks  
Blinking of the  
red lamp  
Turned  
OFF  
There is a possibility that the interior portion has become heated. Turn the power OFF and wait  
approximately 20 minutes. After the main unit has cooled down, please confirm whether or not  
there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or  
not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,  
turn the power ON again; if the same display is displayed, then please contact a sales store or a  
service company.  
The red lamp is  
lighted, or  
blinks  
The red lamp is  
lighted  
Turned  
OFF  
There is a possibility that the interior portion has become overcooled. Please use the unit within  
the usage temperature parameters (0°C to 35°C). After performing any needed maintenance,  
turn the power ON again; if the same display is displayed, then please contact a sales store or a  
service company.  
The green lamp  
is lighted  
Alternative blinking  
with the red lamp  
This is a notification that it is time to clean the filter.  
After cleaning the filter, operate the FILTER TIME portion of the OPTION Menu, and perform  
reset of the FILTER TIME.  
The green  
Simultaneous blinking  
with the red lamp  
lamp is lighted  
NOTE  
When the interior portion has become overheated, for safety purposes, the power source is automatically turned OFF,  
and the indicator lamps may also be turned OFF. Press the ” (power OFF) side of the main power switch, and wait  
for approximately 20 minutes. Please then use the unit only after having first confirmed that the unit has sufficiently  
cooled down.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued)  
Phenomena That May Easily Be Mistaken for Machine Defects  
Before requesting repair, check in accordance with the following chart.  
If the situation cannot be corrected, then contact your dealer.  
Reference  
Page(s)  
Phenomenon  
Cases not involving a machine defect  
Items to be confirmed  
The main power source is not ON.  
Turn on the main power.  
3, 14  
The electrical power cord is not plugged in.  
Correctly connect the power cord.  
Be sure to press the “  
of the main power switch, and leave this OFF  
interrupted during operation, such as by for approximately 20 minutes. After the unit  
O” (power OFF) side  
Power does not  
come ON  
The main power source has been  
14  
a power outage (blackout), etc.  
has sufficiently cooled down, turn ON the  
power source.  
The input changeover settings  
are mismatched.  
Select the input signal, and  
correct the settings.  
15  
10, 11  
10, 11  
17  
No sound or  
pictures are  
outputted  
No signal is being inputted.  
Correctly connect the connection cord.  
Correctly connect the connection cord.  
Adjust the VOLUME setting to a higher level.  
The electrical wiring to this unit  
is not correctly connected.  
Pictures are  
displayed, but no  
sounds are heard  
The volume setting has been set at (or  
adjusted to) an extremely low level.  
Press the MUTE button to release  
(change) the MUTE mode setting.  
The MUTE mode is the current setting.  
17  
The electrical wiring to this unit  
is not correctly connected.  
Sounds are  
heard, but no  
pictures are  
displayed  
Correctly connect the connection cord.  
10, 11  
24  
The brightness setting has been set at Adjust the BRIGHT setting to a  
(or adjusted to) an extremely low level.  
brighter level.  
Colors have a faded-  
out appearance  
Color tone is poor  
Perform picture adjustments by changing the  
COLOR BAL R, the COLOR BAL B, and/or the  
TINT settings, etc.  
Color depth setting or color tone setting  
25  
The brightness setting and/or contrast  
setting has not been properly adjusted.  
Perform picture adjustments by changing the  
BRIGHT and/or CONTRAST settings, etc.  
24  
28  
The WHISPER mode is the current Change (by releasing) from the  
setting. WHISPER mode.  
Pictures appear  
dark  
Lamp is approaching the end of its Exchange the old lamp with a new  
30, 31  
15, 25  
product lifetime.  
Pictures appear Either the FOCUS setting or the H  
PHASE is not properly adjusted.  
lamp.  
Adjust the FOCUS and H PHASE settings.  
blurry  
NOTE  
Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and  
such do not constitute or imply a machine defect.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
NOTE This specifications are subject to change without notice.  
Item  
Specification  
Product name  
Liquid crystal projector  
1.8 cm (0.7 type)  
Panel size  
Liquid  
crystal  
panel  
Drive system  
TFT active matrix  
S50480,000 pixels (800 horizontal x600 vertical)  
X50786,432 pixels (1024 horizontal x 768 vertical)  
Pixels  
Lens  
Zoom lens F=1.7 ~ 2.1 f=36.8 ~ 47.8 mm  
Lamp  
150 W UHB  
Speaker  
1.0W  
Power supply  
Power consumption  
Temperature range  
Size  
AC100 ~ 120V, 2.7A / AC220 ~ 240V, 1.3A  
240W  
0 ~ 35°C (Operating)  
316 (W) x 93 (H) x254 (D) mm (Not including protruding parts)  
Weight (mass)  
2.9 kg  
RGB Terminal  
AUDIO Terminal  
rgb in(1, 2) .....................2  
audio in(R, L) .................1  
VIDEO Terminal  
OUT Terminal  
video in ...........................1  
s-video in .......................1  
component video  
rgb out.............................1  
CONTROL Terminal  
control ............................1  
usb .................................1  
Terminal  
(Y, CB/PB,CR/PR)......1  
Dimension Diagram  
316  
91  
mm  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ACCESSORIES  
Accessories ................................................................ Part Number  
UHB Lamp, 150W .................................................................................... 78-6969-9599-8  
Air Filter Assy ........................................................................................... 78-8118-9182-5  
Power Cord (US) ...................................................................................... 78-8118-8102-4  
Power Cord (UK) ...................................................................................... 78-8118-8101-6  
Power Cord (Europe) ............................................................................... 78-8118-8103-2  
VGA Cable ............................................................................................... 78-8118-8708-8  
RCA Video/Audio Cable ........................................................................... 78-8118-3234-0  
RCA Component Cable w/core ................................................................ 78-8118-9056-1  
USB cable ................................................................................................ 78-8118-9057-9  
Remote Control ........................................................................................ 78-8118-9185-8  
Soft Case .................................................................................................. 78-8118-9193-2  
Not Included with Basic Packet .......................................... Part Number  
Ceiling Mount ........................................................................................... 78-6969-9695-4  
Adjustable Height Suspension ................................................................. 78-6969-9698-8  
Shipping Case .......................................................................................... 78-6969-9716-8  
S-Video Cable .......................................................................................... 78-8118-3238-1  
Mouse Cable (PS/2) ................................................................................. 78-8118-8105-7  
Mouse Cable (Serial) ............................................................................... 78-8118-8107-3  
Mouse Cable (ADB) ................................................................................. 78-8118-8106-5  
RS-232C Cable ........................................................................................ 78-8118-3312-4  
Soft case with shoulder strap ................................................................... 78-6969-9715-0  
Soft rolling luggage case .......................................................................... 78-6969-9716-8  
Ultra value warranty S50 (US only) .......................................................... 78-6969-9704-4  
Ultra value warranty X50 (US only) .......................................................... 78-6969-9705-1  
Mac Adapter ............................................................................................. 78-8118-3308-2  
How to Order  
Please order these parts through your dealer, or contact 3M Customer Service at the  
following number:  
In U.S. or Canada : 1-800-328-1371  
In other locations, contact your local 3M sales office.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
Intended Use  
Before operating this machine, please read this entire manual thoroughly. The 3MTM Multimedia Projectors are designed, built, and tested for use indoors,  
using 3M lamps, 3M ceiling mount hardware, and nominal local voltages.  
The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector peripheral equipment  
and/or create a potentially unsafe operating condition.  
3M Multimedia projectors and Wall Display Systems are designed to operate in a normal office environment.  
16˚ to 29˚C (60˚ to 85˚ F)  
10- 80 %RH (without condensation)  
0- 1828 m (0-6000 feet) above sea level  
The ambient operating environment should be free of airborne smoke, grease, oil and other contaminates that can affect the operation or performance of the  
projector.  
Use of this product in adverse conditions will void the product warranty.  
Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're the only  
transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call  
us toll-free in the continental United States and Canada, 24 hours a day, or visit our Internet Website.  
3M Austin Center  
3M Canada  
3M Mexico, S.A. de C.V.  
3M Europe  
Building A145-5N-01  
6801 River Place Blvd.  
Austin, TX 78726-9000  
P.O. Box 5757  
London, Ontario  
N6A 4T1  
Apartado Postal 14-139  
Mexico, D.F. 07000  
Mexico  
Boulevard de l'Oise  
95006 Cerge Pontoise Cedex  
France  
Litho in Japan  
© 3M 2003  
78-6970-9348-8 Rev. A  
DN00571 (S50/X50_OG_ENG)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Technicolor Thomson Camcorder VMD 6 User Manual
Teledyne Marine Instruments 5499 User Manual
Toshiba Flat Panel Television 20AS23 User Manual
Toshiba Network Card S2T User Manual
TP Link Network Router 150Mbps Universal WiFi Range Extender User Manual
Trane Video Game Controller CNT APG002 EN User Manual
Uniden Two Way Radio GMRS680 User Manual
Vivotek Home Security System FD8164 User Manual
Volvo Automobile C30 User Manual
Wayne Dalton Garage Door Opener 3790 User Manual