®
Vision Model 40
Vision Model 40ET
Owner's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents
Table of Contents .......................................................................................................... 1
Warning .......................................................................................................................... 4
Two Year Limited Warranty ....................................................................................... 6
Overview ........................................................................................................................ 8
Features ...................................................................................................................................... 8
Projector Exterior View ......................................................................................................... 10
Front / Upper Side ........................................................................................................................................ 10
Rear / Bottom Side ....................................................................................................................................... 11
Controls and Functions .......................................................................................................... 12
Control Panel ................................................................................................................................................ 12
Connector Panel ........................................................................................................................................... 14
Remote Control ............................................................................................................ 15
Installation ................................................................................................................... 17
Remote Control ...................................................................................................................... 17
Projector .................................................................................................................................. 18
Connect the Power Cord ............................................................................................................................... 18
Adjust the Lens Zoom/Focus ring ................................................................................................................ 18
Adjust the height ........................................................................................................................................... 19
Installation For Vision Model 40 (With 1.38 - 1.63 Lens) ................................................... 20
Throw Distance Chart For Vision Model 40 (With 1.38 - 1.63 Lens) ................................ 21
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Installation For Vision Model 40ET (With 1.83 - 2.40 Lens) .............................................. 22
Throw Distance Chart For Vision Model 40ET (With 1.83 - 2.40 Lens) ........................... 23
Connecting ................................................................................................................... 24
Connecting Video Inputs ........................................................................................................ 25
Video / S-Video / Component (Interlaced Video) ....................................................................................... 25
Progressive Component (DTV Y/PB/PR) .................................................................................................. 26
RGBHV (DTV RGB) ................................................................................................................................... 27
Connecting a Computer or HDCP Compatible Video Device With DVI-I Output .......... 28
Basic Operation ........................................................................................................... 29
Turning on the Power ............................................................................................................. 29
Zoom/ Focusing ....................................................................................................................... 30
Selecting Video Memory ........................................................................................................ 30
Selecting Input Source ............................................................................................................ 31
Setting Menu ........................................................................................................................... 31
Selecting "ASPECT RATIO" ................................................................................................ 32
PIP/ POP function ................................................................................................................... 32
Turning off the Power ............................................................................................................ 33
Menu ............................................................................................................................. 34
Using the Menu ....................................................................................................................... 34
Main Menu .............................................................................................................................. 35
Picture Quality Adjustments ................................................................................................. 35
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Image Options 1 ...................................................................................................................... 36
Input Select ................................................................................................................................................... 36
Aspect Ratio ................................................................................................................................................. 37
Image Option 2 ........................................................................................................................ 38
Projector Status ....................................................................................................................... 39
Install ........................................................................................................................................ 40
Service ...................................................................................................................................... 41
White Balance ............................................................................................................................................... 41
Blue Enable ................................................................................................................................................... 42
Reset Lamp Timer ........................................................................................................................................ 42
Additional Information ............................................................................................... 43
Replace the Lamp (Contact your Vidikron Dealer) ............................................................ 43
Troubleshooting ...................................................................................................................... 44
Specifications ........................................................................................................................... 46
Dimensions ............................................................................................................................... 48
RS-232 Setup ........................................................................................................................... 49
RS-232C Control Codes ............................................................................................................................... 49
PC Out Adapter ............................................................................................................................................ 50
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Vidikron Vision Model 40/ Vision Model 40ET Owner’s Manual
Thank you for your purchase of this quality Vidikron video projector. It has been designed to provide you with the quality of video that is
expected in a high performance home theater. For the best results, please read this manual carefully as it is your guide through the menus
and operation.
Warning
This symbol is intended to alert the user to the presence of uninsulated
" dangerous voltage " within the product's enclosure that may be of suf-
ficient magnitude to constitute a risk of electric shock.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
This symbol is intended to alert the user to the presence of important
DO NOT REMOVE COVER (OR BACK)
operating and maintenance (servicing) instructions in the literature
NO USER SERVICEABLE PARTS INSIDE.
accompanying the appliance.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
1.
2.
3.
4.
5.
Read these instructions.
Keep these instructions.
Heed all warnings.
Do not use this projector near water, outdoors or otherwise exposed to the elements.
Clean only with a dry cloth.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
6.
7.
Do not block any ventilation openings.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce
heat.
8.
Do not defeat the safety feature of the polarized or grounding type plug. A polarized type plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding prong. The third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
9.
Do not connect the RJ-11, RS-232 jack to a telephone line connection.
10. The 12V trigger outputs 12V DC for triggering. Do not connect to any other power input or output. This could cause damage to this
unit.
11. Only use accessories specified by Vidikron.
12. Keep the packing material in case the projector should ever need to be shipped.
13. Unplug this projector during lightning storms or when it will not be used for an extended period of time.
14. The lamp becomes extremely hot during operation. Allow the projector to cool down for approximately 45 minutes prior to removing
the lamp assembly for replacement. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond rated life
could cause them to explode in rare occasions.
Refer all servicing to qualified service personnel. Servicing is required when the projector has been damaged in any way, objects have fallen
or spilled into the projector, the projector has been exposed to rain or moisture, does not operate normally, or has been dropped.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Two Year Limited Warranty
Congratulations on your purchase of a Vidikron video product and welcome to the Vidikron family! With proper installation, setup and care,
you should enjoy many years of unparalleled video performance.
This is a LIMITEDWARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your other
important documents.
WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
SERVICE LABOR: Vidikron will pay for service labor by a Vidikron Authorized Service Center when needed as a result of a
manufacturing defect for a period of two (2) years from the effective date of delivery to the end user (excluding the lamp).
PARTS: (Not including the lamp) Vidikron will provide new or rebuilt replacement parts for the parts that fail due to defects in materials or
workmanship for a period of two (2) years from the effective date of delivery to the end user. Such replacement parts are then subsequently
warranted for the remaining portion (if any) of the original warranty period.
PROJECTOR LAMP: Vidikron will pay for service labor by a Vidikron Authorized Service Center when needed as a result of a
manufacturing defect for a period of six (6) months or 1000 hours, whichever comes first, from the effective date of delivery to the end user.
In addition, Vidikron will provide a new or rebuilt replacement lamp for the lamp that fails due to defects in materials or workmanship for a
period of six (6) months or 1000 hours, whichever comes first, from the effective date of delivery to the end user. Such replacement lamps
are then subsequently warranted for the remaining portion (if any) of the original warranty period.
WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does not cover
normal maintenance. This Limited Warranty does not cover cabinets or any appearance items; failure resulting from accident, misuse, abuse,
neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper maintenance, alteration, improper use
of any input signal; damage due to lightning or power line surges, spikes and brownouts; damage that occurs during shipping or transit; or
damage that is attributed to acts of God. In the case of remote control units, damage resulting from leaking, old, damaged or improper
batteries is also excluded from coverage under this Limited Warranty.
CAUTION: THIS LIMITED WARRANTY ONLY COVERS VIDIKRON PRODUCTS PURCHASED FROM VIDIKRON
AUTHORIZED DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS
LIMITED WARRANTY. MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION
OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Two Year Limited Warranty
RIGHTS, LIMITS AND EXCLUSIONS:
Vidikron limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There are no
express warranties. Vidikron also excludes any obligation on its part for incidental or consequential damages related to the failure of this
product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the
exclusion or limitation of incidental or consequential damages. So the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights that vary from state to state.
EFFECTIVE WARRANTY DATE:
This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as evidence of the
purchase date.
IMPORTANT: WARRANTY REGISTRATION:
Please fill out and mail your warranty registration card. It is imperative that Vidikron knows how to reach you promptly if we should
discover a safety problem or product update for which you must be notified.
CONTACT A VIDIKRON AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE
Repairs made under the terms of this Limited Warranty covering your Vidikron video product will be performed at the location of the prod-
uct, during usual working hours, providing location of product is within normal operating distance from a Vidikron Authorized Service Cen-
ter. In some instances it may be necessary for the product to be returned to the Vidikron factory for repairs. If, solely in Vidikron's judgment,
location of product to be repaired is beyond normal operating distance of the closest Vidikron Authorized Service Center, or the repair
requires the unit be returned to the Vidikron factory, it is the owner's responsibility to arrange for shipment of the product for repair. These
arrangements must be made through the selling Vidikron dealer. If this is not possible, contact Vidikron directly to locate an authorized Vid-
ikron representative who will assist you in getting a return authorization. Vidikron will return product transportation prepaid in the United
States, unless no product defect is discovered. In that instance, shipping costs will be the responsibility of the owner.
ADDITIONAL INFORMATION:
To locate the name and address of the nearest VIDIKRON authorized service location, or for additional information about this warranty,
please call or write:
VIDIKRON
Attn: Customer Service Department
2900 Faber Street
Union City, CA 94587
Ph: (510) 324-5900
Fax: (510) 324-5905
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Overview
Features
TM
■ 1280 x 720 Widescreen Native 16:9 Resolution HD-2 DMD
Display Device
■ Integrated Video Processing With 3:2 Pulldown
■ 950 ANSI Lumens/ 1600:1 Contrast Ratio
■ Multiple Aspect Ratios with Intelliwide Mode
■ HDTV Ready
480P, 1080i and 720P (576P PAL Version) formats are all compatible with this unit (via an external DTV decoder, not provided).
■ DVI-I Input with HDCP
■ 9-Point White Balance System for Excellent Gray Scale Tracking
■ Direct IR and RS-232 Control
■ ‘Cat’s Eye’ Optical System for Enchanced Contrast and Black Levels
■ Two Lens Options with Variable Throw Distances for Versatile Installation Convenience
■ De-interlacing with 3:2 Pull-down
Using Vidikron’s proprietary de-interlacing technology, this projector provides exceptional scaling and film to video (3:2 pulldown) conver-
sion for the most artifact-free images possible.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
■ PIP/ PBP function
Picture in picture/ Picture by picture functions allow you to display two inputs on the screen at the same time.
■ Video Memory
This projector allows the user to store up to three different settings per input.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Projector Exterior View
Front / Upper Side
1. Front Lamp Cover
Remove this cover when replacing the lamp. (See page 43.)
2. Projection Lens
3. Front IR Sensor
4. Ventilation Holes (intake)
5. Ventilation Holes (exhaust)
6. Focus Ring and Zoom Ring Access
Adjusts the focus and zoom of image.
7. Control Panel
Shows lamp status and whether the projector is on or off.
For more details, see "Control Panel" on page 12.
8. Kensington Lock
This lock can withstand 150 N of force.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
Rear / Bottom Side
1. Connector Panel
6. Ventilation Holes (intake)
For more details, see "Connector Panel" on page 14.
7. Rear Adjusters
Adjusts the height or projection angle.
2. Back IR Sensor
8. Front Adjusters
3. AC Power IN Socket
Adjusts the height or projection angle.
4. AC Power Switch
9. Ceiling Mount Holes
AC main power switch.
The connecting holes for ceiling mount device.
5. Ventilation Holes (exhaust)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
1. STANDBY/ON
8. POWER LED
Indicates power status
Press this key for ONE second to turn on the unit when it is in the
standby mode. Or press this key to turn off this unit when it is on.
■ Lit orange when the AC power cord is plugged into the wall outlet
(standby mode). Once in the standby mode, you can press the
STANDBY/ON key on the projector or the ON key on the remote
control for ONE second to turn on the projector.
2. INPUT
Switches input sources sequentially.
■ Lit green when the power is turned on (operational mode).
■ Flashes orange for the first 30 seconds after powering up, indicating
that the lamp is warming up.
■ Flashes green for one minute after the projector is turned off to
indicate that the lamp is cooling down.
3. MEMORY
Sequentially recalls settings 1 ~ 3 saved to memory. (Please see
"Selecting Video Memory" on page 30.)
4. MENU
9. LAMP LED
Turns the on-screen display control menu on or off.
Indicates the status of lamp.
5. ENTER
■ Lit red when the lamp has developed a problem. Please contact your
Enters settings for items shown in the menu.
Vidikron dealer for assistance.
6. EXIT
10. Zoom Ring
Exits and saves the setting(s) of items in the menu.
Adjusts the size of image
7. ARROW (c/e/d/f)
■ Rotate clockwise to enlarge the image or rotate counterwise to make
the image smaller.
Use to select the menu or to make various adjustments.
11. Focus Ring
Adjust the focus of the projected images.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Connector Panel
1. Video (RCA Jack)
Composite video signal input.
2. S-Video (mini DIN 4-pin)
Y/C (S-video) signal input
3. Component (RCA Jacks)
480i Component (Y/CB/CR) video signal input
4. RGB/ HDTV (BNC) or Progressive Scan DVD players
DTV Y/PB/PR or DTV RGB video signal input.
5. DVI-I
Digital/ Analog signal input.
6. RS-232C (RJ-11 Jack)
RS-232C control signal input.
7. 12v Trigger (mini jack with the diameter of 5.5 mm outside and 2.5 mm inside)
+12V output, active when the projector is turned on.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
Remote Control
ON
MEMORY
Hold down this button for ONE second to turn
on the unit.
M1, M2, M3, DEFAULT
OFF
Recall video memory sequentially (see "Selecting
Video Memory" on page 30)
Press this button to turn off the unit.
INPUT SELECT
VIDEO
ARROW (c,e,d,f)
Composite video signal input
S-VIDEO
Use to select the menu or to make various
adjustments.
ENTER
S-Video signal input
COMP
Enter the setting of items in the menu.
Component Y/CB/CR input
COMP HD
DTV Y/PB/PR signal input
RGB HD
DTV RGBHV signal input
DVI
Digital/ Analog signal input
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
EXIT
Exit and save the setting(s) of items in the menu.
MENU
Turns on/off the on-screen display menu.
PICTURE IN PICTURE
PIP (Picture in Picture)
ASPECT RATIO
ANAMORPHIC
Enable the PIP function. Use ARROW keys to
adjust the position of the PIP window (see "PIP/
POP function" on page 32)
For 16: 9 DVDs.
4 X 3
PIP+
The input signal will be scaled to fit 4: 3 display
mode in the center of screen.
Enlarge the size of PIP window.
PIP-
LETTERBOX
Letterbox mode. Image in letter- box format is
enlarged to fit 16:9 full screen display and the
upper/lower portion are “blanked off”.
Shrink the size of PIP window.
ACTIVE
Switch to the active window in PIP display
mode.
I-WIDE (IntelliWide)
4:3 image is enlarged nonlinearly in horizontal
direction to fit 16: 9 full screen display.
POP (Picture On Picture)
Enable the POP function.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
Remote Control
Push down on the tab and lift to open the cover. Install the two AAA
batteries with the correct polarity, then close the cover.
Notes on Batteries
■
■
■
Make sure that the battery polarities are correct when installing the batteries.
Do not mix an old battery with a new one or different types of batteries.
If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage.
Notes on Remote Control Operation
■
■
Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the projector.
The useable range is between 3m/ 9.8 feet (from the front of the projector) and 4m/ 13.1 feet (from the top of the projector) within a
30 degree horizontal angle and 15 degree vertical angle.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Projector
Connect the Power Cord
Plug the supplied power cord into the AC inlet in the rear of this unit. (AC 100V ~ 240V)
Turn on the main power switch on the rear of this unit (next to the AC inlet). The POWER LED
will light up in orange. Press ON key on the remote control for ONE second to turn on the unit.
Adjust the Lens Zoom/Focus ring
Adjust the projected image size you need with the zoom ring on the lens.
To focus the image, rotate the focus ring on the lens.
Focus
Zoom in
Zoom out
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Installation For Vision Model 40 (With 1.38 - 1.63 Lens)
Ceiling
Between 6.10 - 27.36 in. (155 - 695 mm)
4.89 in. (124.2 mm)
5.51 in. (140 mm)
Screen __________ (H) x __________ (W)
B) THROW DISTANCE:
V40 16 x 9 Screens:
Minimum: (screen width x 1.38) = __________ inches
Maximum: (screen width x 1.63) = __________ inches
C) VERTICAL OFFSET:
Screen width x 0.052 = _________ inches from the center of the lens.
Floor
4.89 in. (124.2 mm)
5.45 in.
(138.4 mm)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Throw Distance Chart For Vision Model 40 (With 1.38 - 1.63 Lens)
Vision Model 40 @ 1280 x 720
Max Throw
Distance
Vertical Offset
Position
Screen Height
Screen Width
Min Throw Distance
40.5
43
45
47
49
50
51.5
52
54
56
58
58.5
60
61
63
65
67.5
72
80
82
72
77
80
84
87
89
92
93
96
100
103
104
107
109
112
116
120
128
142
146
160
99.36
106.26
110.40
115.45
120.06
122.82
126.96
128.34
132.48
138.00
142.14
143.52
147.66
150.42
154.56
160.08
165.60
176.64
195.96
201.48
220.80
117.36
125.51
130.40
136.37
141.81
145.07
149.96
151.59
156.48
163.00
167.89
169.52
174.41
177.67
182.56
189.08
195.60
208.64
231.46
237.98
260.80
3.74
4.00
4.16
4.35
4.52
4.63
4.78
4.84
4.99
5.20
5.36
5.41
5.56
5.67
5.82
6.03
6.24
6.66
7.38
7.59
8.32
90
Screen Hight
Screen Width
Min TD
Max TD
Vertical Offset
(SWx1.38)
(SWx1.63)
Screen Width x 0.052
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Installation For Vision Model 40ET (With 1.83 - 2.40 Lens)
Screen __________ (H) x __________ (W)
B) THROW DISTANCE:
V40ET 16 x 9 Screens:
Minimum: (screen width x 1.83) = __________ inches
Maximum: (screen width x 2.40) = __________ inches
C) VERTICAL OFFSET:
Two inches offset means that the center of the projection lens is 2" above
the top of the screen (inverted ceiling) or 2" below the bottom of
the screen (upright floor mount).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Throw Distance Chart For Vision Model 40ET (With 1.83 - 2.40 Lens)
Vision Model 40ET @ 1280 x 720
Max Throw
Distance
Vertical Offset
Position
Screen Height
Screen Width
Min Throw Distance
40.5
43
45
47
49
50
51.5
52
54
56
58
58.5
60
61
63
65
67.5
72
80
82
72
77
80
84
87
89
92
93
96
100
103
104
107
109
112
116
120
128
142
146
160
131.76
140.91
146.40
153.10
159.21
162.87
168.36
170.19
175.68
183.00
188.49
190.32
195.81
199.47
204.96
212.28
219.60
234.24
259.86
267.18
292.80
172.80
184.80
192.00
200.78
208.80
213.60
220.80
223.20
230.40
240.00
247.20
249.60
256.80
261.60
268.80
278.40
288.00
307.20
340.80
350.40
384.00
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
90
Screen Hight
Screen Width
Min TD
Max TD
Vertical Offset
(SWx1.83)
(SWx2.40)
2.00”
Two inches offset means that the center of the projection lens is 2” above the top of the screen (inverted ceiling) or 2” below the bottom of the
screen (upright floor mount).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Connecting a Computer or HDCP Compatible Video Device With DVI-I Output
PC, Notebook, set top box
or other video device with
DVI output
This unit is compatible with the following computer resoultions: 1280x720, 1024x768, 800x600, 640x480.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Basic Operation
Turning on the Power
■ The Power LED lights orange when power is applied and the power switch is turned
on.
■ Press and hold the ON key on the remote control or the Power key on the projector
for ONE second to turn on the unit. The POWER LED will blink orange during
warm up period, then light solid green.
■ " Searching…." will be displayed on the screen before the projector identifies the
input signal. This message will remain on the screen until a valid signal is detected.
■ If an incompatible input signal exceeds the range of the projector a "Not supportive
timing" message will be displayed on the screen. This message will remain on the
screen until you change the input signal.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Zoom/ Focusing
■ Adjust the projection image size you need with the zoom ring on the
lens. To focus the image, rotate the focus ring on the lens.
Focus
Zoom in
Zoom out
Selecting Video Memory
■ Press MEM1, MEM2, MEM3 buttons to recall
settings in the memory.
■ Press DEFAULT to select the default setting.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Selecting Input Source
■ When this unit is turned on, it will search for
the input source you last selected.
■ You may select the input source directly on
the remote control.
Setting Menu
■ Press the Menu button to turn on /off the on-screen menu.
■ Use the ARROW buttons (c,e,d,f) to select the menu or
to make various adjustments.
■ Press the Enter or f button to enter the setting of items in
the menu, or press the Exit button to leave and save the
setting of items in the menu.
■ For more detailed settings, see Chapter 5 Menu on page 34.
■ Press Picture to access the picture setting menu.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Selecting "ASPECT RATIO"
■ Select the proper aspect ratio according to the content being used. There are four aspect
ratios for choice.
■
ANAMORPHIC: The image is compressed vertically, but anamorphic
software will appear properly proportioned. This is best suited for use with
16:9 DVD's.
■
■
■
4 X 3: The input signal will be scaled to fit 4 : 3 display mode in the center
screen.
LETTERBOX: Image in letterbox format is enlarged to fit 16:9 full screen
display and the upper/lower portion are cropped.
I-WIDE: This transforms a 4x3 image to a 16x9 image.
PIP/ POP function
■ Press the PIP button to enable the PIP function.
■ For PIP purposes, there are two groups of inputs separated by their display modes:
Video Group: Video, S-Video and Component Y/CB/CR inputs
Graphic Group: HDTV input and Computer input.
■ The PIP can show one input from the Graphic Group within one input from the Video
Group, or show one input from Video Group within one input from the Graphic Group.
■ Press the PIP button to switch to the main window or turn off PIP function.
■ Select the input source of the main window by pressing the INPUT button.
■ Press the ACTIVE button to switch to the active window. You can change the input signal setting in the active window.
■ Press PIP+ or PIP- to adjust the size of PIP window.
■ Adjust the position of the PIP window with the ARROW keys (c,e,d,f).
■ Press POP to enable the POP function.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning off the Power
■ Press the OFF key on the remote control to turn off the
unit.
■ The POWER LED will blink green and the fans will
speed up for a quick cool down. The projector will not
respond to any command for 90 seconds.
■ The POWER LED will light solid orange once the
cooling down cycle has completed.
■ Fans will run for three minutes to cool.
■ You may turn the projector back on after the first 90
seconds.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Menu
Using the Menu
This unit is equipped with an on-screen display (OSD) menu for making various adjustments and settings.
There are five different menu languages; see page 40 Language setting for more details.
■ Press the Menu button to turn on /off the on-screen display menu.
■ Use the ARROW buttons (c,e,d,f) to select the menu or to make various adjustments.
■ Press the Enter or f button to enter the setting of items in the menu, or press the Exit button to leave and save the setting of items in the
menu.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
Main Menu
When the Menu button is pressed on the remote control, the main menu will appear on-screen. An
example of the main menu is shown right. Use c or d button to move the item you want to choose
and then press the Enter or f button.
Vision Model 40
Picture Adjust
Image Option
Projector Status
Install
Service
Picture Quality Adjustments
To access the picture quality adjustments, press
Menu, highlight Picture Adjust and press Enter
or f. The picture adjust sub-menu will then appear
(see above).
Vision Model 40
Picture Adjust
Picture Adjust
To make an adjustment to a particular function,
Brightness
+30
+15
+30
+15
0
highlight the function with the c or d arrow but-
Image Options
Contrast
Color
ton and press Enter or fto activate a scroll bar for
that adjustment. When all the settings are done,
press Exit to leave the current submenu and then
Status
Tint
go to Image options --> Memory Store for saving
the values as Memory 1, Memory 2 or Memory 3.
Install
Sharpness
Color Temp.
4
Service
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Image Options 1
Image Options
Input Select
Video
Input Select
Aspect Ratio
Aspect Ratio
Anamorphic
Standard (4/3)
Letterbox
HD/RGB Adjust
S-Video
Memory Store
Memory Recall
Component
Component HD
RGB HD
IntelliWide
DVI-I
Input Select
From Input Select submenu, you are free to choose one of the 6 input sources as long as you are sure the projector is connected with the
correct signal cables. In the example above, S-Video is the current source.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
Aspect Ratio
There are four aspect ratios available that can be selected for video signal inputs.
16:9 Screens:
■ Anamorphic: The image is compressed vertically, but anamorphic software will appear properly
proportioned. This is best suited for use with 16:9 DVD's.
Active Image Area
■ Standard (4/3): The input signal will be scaled to fit in the center of the 16:9 screen.
Active Image
Area
■ Letterbox: The image in the Letterbox mode will be zoomed in, and the top and bottom portion
'blanked off'. This ratio is best suited for LaserDisc movies or non-anamorphic DVD's.
Active Image Area
■ I-WIDE: A 4:3 image is transformed into a 16:9 image.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Image Option 2
HD/RGB Adjust
Image Options
Auto.
YES ?
Freq.
Input Select
Aspect Ratio
0
0
0
0
Phase
H. Pos.
V. Pos.
HD/RGB Adjust
Memory Store
Memory 1
Memory Store
Memory Recall
Memory Recall
Memory 1
Memory 2
Memory 2
Memory 3
Memory 3
HD/RGB Adjust.: The following settings are only available with a PC or DTV RGB signal. There is no position adjustment when using
DVI-D signal.
■ AUTO: Adjusts the phase, frequency and position automatically.
■ Freq.: Adjusts the frequency of the signal.
■ Phase: Adjusts the phase of the input signal.
■ H. Pos.: Adjusts the horizontal position of the image.
■ V. Pos.: Adjusts the vertical position of the image.
To enter into the memory selection menus, use Memory Store and Memory Recall menus to save and load up to three different memories.
There are three memories: Memory 1, Memory 2 and Memory 3.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
Projector Status
Vision Model 40
Picture Adjust
Image Options
Status
Projector Status
Default
Load
Install
Sleep Timer
Lamp Hours
Minutes
60
Service
Hours
+63
M
Minutes
+59
Default: Use this function to reset all values of the current source back to factory default.
Sleep Timer: To setup auto off timer. The setting timer is from 10 minutes to 3 hours.
Lamp Hours: To check for total time of lamp usage.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Install
Language
Install
Picture Configuration
English
Francais
Espanol
Deutsch
Italiano
Language
Picture Configuration
Keystone
Floor Front
Ceiling Front
Floor Rear
Keystone
Keystone
0
Ceiling Rear
OSD Position
OSD Position
H. POS.
0
Background Color
V. POS.
0
Background Color
Test Patterns
Grey
Blue
White
Press Enter on selected feature to open the Install menu.
Language: There are 5 different menu languages available: English, French, Spanish, German and Italian.
Picture Orientation: The projector can be installed on a ceiling or in a rear screen configuration with one or more mirrors. There are four
settings: FLOOR FRONT, CEILING FRONT, FLOOR REAR, and CEILING REAR.
Keystone: Corrects the trapezoidal distortion as a result of the angle of projection (-12° ~ +12°). This can correct for up to +/- 12 degrees of
offset.
OSD Position: To adjust horizontal and vertical positions of the OSD.
Background Color: To select the background color while there is no input signal detected.
Test Patterns: Highlight and press Enter or the right arrow key to display the cross-coarse pattern.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
Service
The Service menu is passcode protected and for use by Vidikron per-
sonnel only. Many of the adjustments available in this section are
intended for use by trained service personnel only. If you are having
difficulty with one of these items, please contact your Vidikron Dealer
for service.
Vision Model 40
Picture Adjust
Image Options
Status
Install
Please enter pass-code
to access Service screen
Service
White Balance
Gamma
Service
White Balance
Red
66
66
66
White Balance
Green
Blue
Gamma
Blue Enable
Gain
Gain
Lamp Reset Timer
Red
134
Offset
Offset
To adjust grey scale.
512
512
Green
Blue
Store Settings
Red
0
0
0
■ Gamma: Adjust the gamma curve.
■ Gain: Adjust high end.
■ Offset: Adjust low end.
Green
Blue
■ Store Settings: When this function is selected and entered, all White Balance
settings will automatically be stored in Color Temp. 4 (Custom Temperature).
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Blue Enable
This mutes the red and green image.
Use this function in combination with the external color bar pattern to
adjust for proper color and tint settings without using a blue filter.
Service
White Balance
Blue Enable
To quickly exit this function, select any other color temperature in the
same adjustment window and return to the original temperature setting
or simply select another input source from the remote control and then
return to the original selected source.
Blue Enable
Off
On
Lamp Reset Timer
Reset Lamp Timer
Use this function to reset lamp usage counter. Reset only if
you replace the lamp.
Service
Lamp Reset Timer
White Balance
Blue Enable
Reset only if you
replace new lamp
Lamp Reset Timer
ARE YOU SURE?
NO
Yes
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Additional Information
Replace the Lamp (Contact your Vidikron Dealer)
1.
Loosen the screw of front
2.
Take off the front lamp
lamp cover.
cover.
3.
4.
Loosen the three screws
on the lamp shield.
5.
6.
Loosen the two screws on
the lamp module.
Take off the lamp shield.
Pull out the lamp module
horizontally.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
7.
Insert the new lamp mod-
9.
Put on the lamp shield.
ule into the projector hori-
zontally until it is securely
in place.
10. Tighten the three screws on
the lamp shield.
8.
Tighen the two screws on
the lamp module.
13. Turn on the power and go into the Service menu, select Lamp
11. Put on the front lamp cover.
Reset Timer item to reset lamp usage counter.
12. Tighten the screw of front
lamp cover.
Troubleshooting
Problem
Possible Cause
Remedy
There is no power from power cable.
Plug the power cord into the AC inlet on the rear of this
unit, and plug the power cord into to the power outlet.
The power switch is not turned on.
Turn on the power switch.
This unit does not turn
on.
Turned on this unit again while still in the cool- Wait until this unit completes the cooling down proce-
ing down procedure. dure.
The front lamp cover is not correctly attached. Correctly attach the front lamp cover.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
This unit is not correctly connected to the input Check the connection.
source device.
The input signal has not been correctly selected. Select the correct input signal with the input keys: Video,
S-Video, Component, Component HD, RGB HD and
No picture
DVI-I on the remote control.
POWER LED or LAMP LED blinking.
Please contact your Vidikron dealer for assistance.
The connection cables are not connected to this Correctly connect the cables to the appropriate terminals.
unit.
Image is unstable
Picture is blurred
The projection lens is not correctly focused.
Adjust the focus of projection lens with the focus ring.
This unit and the screen are not aligned
squarely.
Adjust the projection angle and direction, and the height
of this unit.
The batteries are exhausted.
Replace both batteries with new ones.
Remote control does
not work correctly
The front lamp cover is not correctly attached. Correctly attach the front lamp cover.
LAMP LED blinks in
red
The cooling fan does not work properly.
Please contact your Vidikron dealer for assistance.
The temperature inside this unit is extremely
high.
Check that the ventilation holes are not blocked.
The lamp has exceeded its estimated life.
The lamp has burned out.
Replace the lamp with a new one.
Replace the lamp with a new one.
POWER LED blinks in
orange and green
sequentially
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
Specifications
Projector Type
Vision Model 40/ Vision Model 40ET Specifications
Inputs
Digital Light Processing™ (DLP™), Single HD-2 DMD™ Chip
(1) Composite Video, (1) S-Video,
(1) RGB/Component (via BNC),
(1) RCA Component Video,
Native Resolution
1280 x 720, (16:9)
(1) DVI-I w/ HDCP, (1) RS-232
Aspect Ratios
4:3, Letterbox, 16:9, Anamorphic, IntelliWide
Scan Frequency:
Horizontal 15-80 kHz, Vertical: 50-100 Hz
Video Standards
NTSC, PAL
Picture Size (16:9 Screen)
Recommended Width: 72-96 in., Maximum Width: 200 in.
Throw Distance
V40: 1.38 to 1.63 / V40ET: 1.83 to 2.40
(Factor x Screen Width): Please refer to page 20 to page 23.
12V Output
Max. 250 Amp, active when the projector is on
Power Requirements
100-240V AC, 50/60 Hz, 320 watts
Light Output
CSMS** Specifications:
Home Theater Calibration:
480 ANSI Lumens, 17.9 Foot-Lamberts (fL)
850 ANSI Lumens*
Operating Environment
40°- 95° F, (5°- 35° C), 20%-80% Humidity (non-condensing)
Dimensions (w/out feet)
Width: 15.8 in. (400 mm),
Depth: 11 in. (280 mm),
Height: Without feet 4.9 in. (125.41 mm)
with feet 5.18 in. (131.5 mm)
Weight: 17.5 lbs. (7.8 kg) (includes lens)
Contrast Ratio
CSMS** Contrast Ratio: 148:1
1600:1 ANSI
Lamp
210W
Estimated Lamp Life
2000 hours @ 6500 Kelvin
Regulatory Approvals
UL, FCC, CE, C-Tick
o
Limited Warranty:
DTV Compatibility
Projector: (2) Two year parts and labor from the date of deliv-
480p, 720p, 1080i
ery to the end user
Memories
21 memories
Lamp Warranty: (6) six months or 1000 hours
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
*ANSI Lumen specification:
This is the typical projector luminosity (brightness) specification found in most sales literature. This measurement is included in Vidikron
literature to allow for direct comparison with other manufacturer's projectors. These measurements can be taken at 9,000 to 13,000 degree
Kelvin to get expected performance data when the projector is used in professional, commercial, and industrial displays.
**CSMS Home Theater Calibration ANSI Lumen Specification:
These measurements are taken from the projector as setup in a home theater environment. The projector is calibrated to ISF specifications
including setting the color temperature to 6500 degree Kelvin, the standard for reproducing video.
**CSMS Home Theater Calibration foot-Lambert (fL) Specification:
This is the unit of measurement used in commercial movie theaters to express image brightness. The Society of Motion Picture and Televi-
sion Engineers (SMPTE) specifies 16 fL as the target image brightness for film-based projectors using an open gate (without film in the pro-
jector). More importantly, today SMPTE specifies 12 fL as the target image brightness in Digital Cinema theaters using DLP™ technology.
The foot-Lambert is dependant on screen size, screen gain, and projector light output.
All measurements are made at Vidikron to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650 SpectraColorimeter
and Minolta LS-100 Light Meter, Video Essentials test DVD, and a Stewart Filmscreen StudioTech 130, 1.3 gain, 72-inch wide screen. The
projector is calibrated to a color temperature of 6500º Kelvin and has a minimum of 150 hours of usage.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
RS-232 Setup
Baud Rate: 115200 or 9600
Parity: None
Data Bits: 8 Bits
Stop Bits: 1 Bit
Flow Control: None
RS-232C Control Codes
Code
X01
X02
X03
X04
X10
X11
X12
X13
X14
X15
X16
X20
X21
X22
Function
X23
X24
X25
X35
X36
X37
X38
X40
X41
X42
X46
X47
X48
X49
X55
Switch to DVI_PC input
Switch to YPBPR input
Switch to BNC_PC input
Anamorphic
X56
X57
X60
X61
X62
X63
X64
X85
X90
X91
X92
X93
X94
X95
Picture in picture display
Power On
Picture by picture display
Switch language - English
Switch language - French
Switch language - Spanish
Switch language - German
Switch language - Italian
Graphic Input - auto
Power Off
Message On
Message Off
Standard
Menu (arrow key)
Enter (arrow key)
Exit (arrow key)
Up (arrow key)
Letter box
I-WIDE
Load memory 1 settings
Load memory 2 settings
Load memory 3 settings
Load default of current source
Save memory 1 settings
Save memory 2 settings
Save memory 3 settings
Switch active source
Image orientation - floor front
Image orientation - ceiling front
Image orientation - floor rear
Image orientation - ceiling rear
Back light on
Down (arrow key)
Left (arrow key)
Right (arrow key)
Switch to Composite input
Switch to S-Video input
Switch to Component input
Back light off
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Vidikron Owner’s Manual
PC Out Adapter
1.
1. Connect D-Sub 9-pin female to RJ-11 adapter (not
included) to Com port on PC.
RS-232 For RJ-11 (not included)
2.
2. Connect RJ-11 to Projector.
4-pin RJ-11
Details
TxT
2
3
RxD
1, 4
Ground
RJ-11 to D-Sub 9-pin (not included)
Yellow
Green
Green
Yellow
1
2
Black
Red
RS-232 For D-Sub 9-pin (not included)
Black
3
4
D-Sub 9-pin female
Details
TxT
Red
2
NOTE:
5
4
3
1
2
3
RxD
6
9
8
7
1.
2.
All codes are in the ASCII format.
A carriage return is required after each command.
5
Ground
NC
1, 4, 6, 7, 8, 9
D-Sub 9-pin female
Warning: During initial turn on and turn off of the projector, this
unit will not accept RS-232 codes for 20 seconds.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
|