KS-AR8004D / KS-AR8002D
POWER AMPLIFIER: INSTRUCTIONS
AMPLIFICATEUR DE PUISSANCE: MANUEL D’INSTRUCTIONS
LVT1813-001A
[J]
ENGLISH
When you use more than one KS-AR8000 series amplifier, you can pile up to three of
them using the provided brackets and hex screws in two ways, X or Y.
1 Attach the provided spacers to the bottom of the amplifier (2 and 3).
Spacer's
bottom
Bottom
Thank you for purchasing an ARSENAL product. Please read all instructions carefully before
operation, to ensure your complete understanding and to obtain the best possible performance
from the unit.
2 Fix the amplifiers on both sides with the brackets (I) as illustrated.
• Be sure to mount the lowest amplifier (1) as illustrated on
.
• Before piling amplifiers as X, first make the connections for the power supply (see
For safety....
“POWER SUPPLY” below) and speakers (see “SPEAKER CONNECTIONS” on page 2).
•
Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.
X
Y
• Stop the car before performing any complicated operations.
Bracket (I)
Bracket (I)
CAUTIONS AND NOTES
Spacer
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems.
• This unit uses BTL (Balanced Transformerless) amplifier circuitry, i.e., floating ground system,
so comply with the following:
Do not connect the “·” terminals of the speakers to each other.
Do not connect the “·” terminals of the speakers to the metal body or chassis.
• Cover the unused terminals with insulating tape to prevent them from short circuiting.
• When an extension lead is used, it should be as thick and short as possible; connect it firmly
with insulating tape.
Spacer
Bracket (L)
Bracket (L)
Side of the unit
• Be sure to leave an appropriate space between the antenna and the wires of this unit.
• When replacing the fuse, use a 30 A fuse for KS-AR8004D or a 25 A fuse for KS-AR8002D.
• Do not let pebbles, sand or metallic objects get inside the unit.
• To keep the heat dissipation mechanism running effectively, wipe the accumulated dust off
periodically.
POWER SUPPLY
• Listening to the tape, radio, CD or Digital Audio Player, etc. with the volume set at a high level
for a long period of time will exhaust the battery, while the engine is turned off or while the
engine is idling.
• This unit becomes very hot. Be careful not to touch the unit not only when using but for a while
after using.
*Not included with this unit.
DO NOT disassemble the units since there are no user serviceable parts inside.
For Customer Use:
Enter below the Model No. and Serial No. which are located on the top or bottom of the
cabinet. Retain this information for future reference.
To metallic body or chassis
Fuse
Model No.
Serial No.
(To an accessory terminal)
Ignition switch
Remote turn-on line
INSTALLATION
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specific car. If you have any questions or require information regarding
installation kits, consult your JVC car audio dealer or a company supplying the kits.
JVC car receiver, etc.
Car battery
CAUTION
Mount this unit on a firm surface, such as in the trunk or under the front seat.
To prevent short circuits while making connections, keep the battery’s negative terminal
disconnected.
• Since heat is generated in the unit, do not mount it near inflammable objects. In addition,
mount it in an area that will not prevent the unit from dissipating the heat.
• Do not mount the unit in the places subject to heat: near a radiator, in a glove compartment
or in insulated areas such as under a car mat that will prevent the unit from dissipating
heat.
1 Remote turn-on line (not included with this unit)
a When you use a JVC car receiver with a remote lead, connect to the remote lead.
b When you connect a unit without a remote lead, connect to the accessory circuit of the
car which is activated by the ignition switch. In this case, noise may occur when the car
receiver is turned on or off. To avoid this noise, do not turn on or off the car receiver itself.
You can turn on or off the car receiver along with the on/off operation of the ignition switch.
2 Ground lead (not included with this unit)
• When mounting the unit under the front seat, make sure that adjusting the seat position
will not catch any wire of the unit.
3 Power cord (not included with this unit)
•
When using a power cord, be sure to add the appropriate fuse near the battery as shown.
– For KS-AR8004D: 40 A
– For KS-AR8002D: 30 A
•
Connect to the battery’s “ª” terminal only after all the other connections have been made.
Under the front seat
Onto the trunk floor
Note
If the Status lamp (see “CONTROLS” on page 3) lights in red, it indicates incorrect speaker
wiring or connections. In this case, see “TROUBLESHOOTING” on page 3. Be sure to correct the
speaker wiring and other connections.
When mounting this unit, be sure to use the provided screws. If any other screws are used,
there is a risk of loosening the unit or damaging parts inside it.
• Before drilling holes in the trunk to install the unit, make sure that there is a sufficient
space under the trunk so that you do not drill holes in the fuel tank, etc.
TERMINAL CONNECTIONS
• To detach and rotate the Logo Plate, use the provided hex wrench (3 mm).
The appropriate wire gauge for each terminal is as follows.
Screw (Dia. 3/16 inch (4 mm)
× 13/16 inch (20 mm))
Bracket (L)
• POWER terminals:
– + B and GND: AWG 8 to AWG 4 (The cross section is about 8 mm2 to 21 mm2.)
– REM: AWG 18 to AWG 8 (The cross section is about 0.8 mm2 to 8 mm2.)
• SPEAKER OUTPUT terminals:
Hex Screw (M4 × 7/16 inch (10 mm))
– AWG 18 to AWG 8 (The cross section is about 0.8 mm2 to 8 mm2.)
If you have any questions regarding the thickness of the power cord, etc., consult your nearest
JVC car audio dealer.
Logo Plate (detachable)
1 Peel off the insulating vinyl cover of a lead to expose the conductor
inside.
•
The exposed conductor should be 5/16 inch (7 mm) to 7/16 inch
(10 mm) long.
– If shorter, it may cause poor conductivity.
– If longer, it may cause a short circuit.
2 Loosen the hex screw in a terminal with the provided hex wrench
Bracket (L)
and insert the conductor into the terminal.
•
Use the appropriate hex wrench for each terminal.
– 4 mm: +B and GND terminals
Drilled hole
– 3 mm: REM and SPEAKER OUTPUT terminals
3 Fix the hex screw again to secure the conductor.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
KS-AR8002D
For more details, consult your JVC car audio dealer.
2-speaker system plus subwoofer (1 amplifier)
The minimum impedance should be 4 Ω for each of the left and right speakers, and the
The Status lamp does not light.
• Change the fuses if the current one is blown.
subwoofer.
Subwoofer
• Confirm the connections for the power supply (see “POWER SUPPLY” on page 1).
• Connect the ground lead securely to a metal part of the car.
• Turn on the equipment connected to this unit.
Line Out
Left speaker
Right speaker
JVC car receiver, etc.
• Use a relay if your system employs so many amplifiers.
• Confirm the battery voltage (11 V to 16 V).
The Status lamp lights in red and/or the unit heats up abnormally.
• Use speakers of a suitable impedance.
• Correct the speaker wirings if they are short-circuited.
• Leave the unit turned off for a while to cool it down.
CROSSOVER
fi lter switch
The Status lamp lights in violet frequently. (Clipping*)
• Lower the input level with the Input LEVEL controller until the lamp lights in violet a few times.
* It means that the amplifier circuits are overloaded and the sound may distort due to too much
input from the car receiver.
No sound is heard.
Control panel
• Confirm the connections for the power supply (see “POWER SUPPLY” on page 1).
• Connect the RCA pin cords to the INPUT jacks.
• Confirm the speaker wirings and the position of the CROSSOVER filter switch (See “SPEAKER
CONNECTIONS” on page 2).
1
2
3
4
*
*
*
*
RCA pin cord (not included with this unit)
Bridge wiring
Use a High-pass crossover (not included with this unit).
Use a Low-pass crossover (not included with this unit).
Alternator noise is heard.
• Keep the leads of the POWER terminals away from the RCA pin cords.
• Keep the RCA pin cords away from other electrical cables in the car.
• Connect the ground lead securely to a metal part of the car.
• Make sure the negative speaker leads do not touch the car chassis.
• Replace the plugs or use plugs with load resistors.
CONTROLS
• Connect a bypass capacitor across the accessory switches (horn, fan, etc.).
To operate the following controls, detach the control cover. Attach it again after operation.
Noise is made when you connect the unit to an AM tuner.
• Move all the leads of this unit away from the antenna lead.
Control cover
SPECIFICATIONS
Power Output
KS-AR8004D: 120 W RMS x 4 channels at 4 Ω and ≤ 1% THD + N
KS-AR8002D: 150 W RMS x 2 channels at 4 Ω and ≤ 1% THD + N
Signal-to-Noise Ratio
80 dBA (reference: 1 W into 4 Ω)
The illustration above is for KS-AR8004D.
KS-AR8004D
Maximum Power Output
Load Impedance
600 W
4 Ω
(Normal mode: 2 Ω to 8 Ω allowance)
(Bridge Mode: 4 Ω to 8 Ω allowance)
Frequency Response
5 Hz to 40 kHz* (+0, –3 dB)
* Subsonic filter cuts off extremely low frequency signals less than
18 Hz.
Input Sensitivity/Impedance
Distortion
2 V /44 kΩ (0.3 V to 6 V, variable)
Less than 0.01% (at 1 kHz)
Power Requirement
Grounding system
Dimensions (W×H×D)
Mass (approx.)
DC 14.4 V (11 V to 16 V allowance)
Negative ground
9-7/8 inch × 2-1/2 inch × 7-3/16 inch (250 mm × 62 mm × 182 mm)
KS-AR8004D: 6.2 lbs. (2.8 kg)
KS-AR8002D: 5.8 lbs. (2.6 kg)
Screw (Dia. 3/16 inch (4 mm) × 13/16 inch (20 mm)) × 4
KS-AR8002D
Accessories
Hex Screw (M4 × 7/16 inch (10 mm)) × 8
Hex wrench
4 mm × 1
3 mm × 1
Spacer × 4
Bracket
L × 4
I × 4
Design and specifications are subject to change without notice.
Status lamp
The lamp normally lights in blue while the unit is turned on.
•
•
•
When the lamp does not light
When the lamp lights in red
When the lamp lights in violet frequently
– It indicates there may be a problem. See “TROUBLESHOOTING” on the right column.
BASS BOOST controller
Turning this boosts the 45 Hz frequency within the range of 0 dB to +18 dB. Adjust the level
while listening to the sound. This control is preset to MIN when the unit is shipped.
Input LEVEL controller
[European Union only]
The input level can be adjusted with this control when this unit is connected to other source
equipment. Adjust the level while listening to the sound. This control is preset to MIN when
the unit is shipped.
CROSSOVER frequency controller
Turning this adjusts the cutoff frequency within the range of 30 Hz to 500 Hz. Adjust the level
while listening to the sound. This control is preset to 30 Hz when the unit is shipped.
CROSSOVER filter switch
OFF: Normally, set to this position. The switch is preset to this position when the unit is
shipped.
LPF: Set to this position when you want to turn on the LPF (Low-Pass Filter) switch (the
Low-Pass Filter transmits frequencies lower than the cutoff frequency).
HPF: Set to this position when you want to turn on the HPF (High-Pass Filter) switch (the
High-Pass Filter transmits frequencies higher than the cutoff frequency).
EN, FR
© 2007 Victor Company of Japan, Limited
1207KMMMDWTKC
3
Download from Www.Somanuals.com. All Manuals Search And Download.
KS-AR8004D / KS-AR8002D
POWER AMPLIFIER: INSTRUCTIONS
AMPLIFICATEUR DE PUISSANCE: MANUEL D’INSTRUCTIONS
1207KMMMDWTKC
EN, FR
LVT1814-001A
[E/U]
© 2007 Victor Company of Japan, Limited
ENGLISH
When you use more than one KS-AR8000 series amplifier, you can pile up to three of
them using the provided brackets and hex screws in two ways, X or Y.
1 Attach the provided spacers to the bottom of the amplifier (2 and 3).
Spacer's
bottom
Bottom
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the
unit.
2 Fix the amplifiers on both sides with the brackets (I) as illustrated.
• Be sure to mount the lowest amplifier (1) as illustrated on
.
• Before piling amplifiers as X, first make the connections for the power supply (see
For safety....
“POWER SUPPLY” below) and speakers (see “SPEAKER CONNECTIONS” on page 2).
•
Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.
X
Y
• Stop the car before performing any complicated operations.
Bracket (I)
Bracket (I)
Spacer
CAUTIONS AND NOTES
Spacer
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems.
• This unit uses BTL (Balanced Transformerless) amplifier circuitry, i.e., floating ground system,
so comply with the following:
Bracket (L)
Bracket (L)
Do not connect the “·” terminals of the speakers to each other.
Do not connect the “·” terminals of the speakers to the metal body or chassis.
• Cover the unused terminals with insulating tape to prevent them from short circuiting.
• When an extension lead is used, it should be as thick and short as possible; connect it firmly
with insulating tape.
Side of the unit
POWER SUPPLY
• Be sure to leave an appropriate space between the antenna (aerial) and the wires of this unit.
• When replacing the fuse, use a 30 A fuse for KS-AR8004D or a 25 A fuse for KS-AR8002D.
• Do not let pebbles, sand or metallic objects get inside the unit.
• To keep the heat dissipation mechanism running effectively, wipe the accumulated dust off
periodically.
• Listening to the tape, radio, CD or Digital Audio Player, etc. with the volume set at a high level
for a long period of time will exhaust the battery, while the engine is turned off or while the
engine is idling.
*Not included with this unit.
• This unit becomes very hot. Be careful not to touch the unit not only when using but for a while
after using.
DO NOT disassemble the units since there are no user serviceable parts inside.
To metallic body or chassis
Fuse
(To an accessory terminal)
Ignition switch
Remote turn-on line
INSTALLATION
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specific car. If you have any questions or require information regarding
installation kits, consult your “JVC IN-CAR ENTERTAINMENT” car audio dealer or a company
supplying the kits.
JVC car receiver, etc.
Car battery
CAUTION
To prevent short circuits while making connections, keep the battery’s negative terminal
disconnected.
Mount this unit on a firm surface, such as in the trunk or under the front seat.
• Since heat is generated in the unit, do not mount it near inflammable objects. In addition,
mount it in an area that will not prevent the unit from dissipating the heat.
• Do not mount the unit in the places subject to heat: near a radiator, in a glove compartment
or in insulated areas such as under a car mat that will prevent the unit from dissipating
heat.
1 Remote turn-on line (not included with this unit)
a When you use a JVC car receiver with a remote lead, connect to the remote lead.
b When you connect a unit without a remote lead, connect to the accessory circuit of the
car which is activated by the ignition switch. In this case, noise may occur when the car
receiver is turned on or off. To avoid this noise, do not turn on or off the car receiver itself.
You can turn on or off the car receiver along with the on/off operation of the ignition switch.
2 Ground lead (not included with this unit)
• When mounting the unit under the front seat, make sure that adjusting the seat position
will not catch any wire of the unit.
3 Power cord (not included with this unit)
•
When using a power cord, be sure to add the appropriate fuse near the battery as shown.
– For KS-AR8004D: 40 A
– For KS-AR8002D: 30 A
•
Connect to the battery’s “ª” terminal only after all the other connections have been made.
Under the front seat
Onto the trunk floor
Note
If the Status lamp (see “CONTROLS” on page 3) lights in red, it indicates incorrect speaker
wiring or connections. In this case, see “TROUBLESHOOTING” on page 3. Be sure to correct the
speaker wiring and other connections.
When mounting this unit, be sure to use the provided screws. If any other screws are used,
there is a risk of loosening the unit or damaging parts inside it.
• Before drilling holes in the trunk to install the unit, make sure that there is a sufficient
space under the trunk so that you do not drill holes in the fuel tank, etc.
TERMINAL CONNECTIONS
• To detach and rotate the Logo Plate, use the provided hex wrench (3 mm).
The appropriate wire gauge for each terminal is as follows.
Bracket (L)
• POWER terminals:
Screw (φ 4 × 20 mm)
– + B and GND: Cross section of 8 mm2 to 21 mm2
– REM: Cross section of 0.8 mm2 to 8 mm2
• SPEAKER OUTPUT terminals:
Hex Screw (M4 × 10 mm)
– Cross section of 0.8 mm2 to 8 mm2
If you have any questions regarding the thickness of the power cord, etc., consult your nearest
“JVC IN-CAR ENTERTAINMENT” car audio dealer.
Logo Plate (detachable)
1 Peel off the insulating vinyl cover of a lead to expose the conductor
inside.
•
The exposed conductor should be 7 mm to 10 mm long.
– If shorter, it may cause poor conductivity.
– If longer, it may cause a short circuit.
2 Loosen the hex screw in a terminal with the provided hex wrench
and insert the conductor into the terminal.
Bracket (L)
•
Use the appropriate hex wrench for each terminal.
– 4 mm: +B and GND terminals
Drilled hole
– 3 mm: REM and SPEAKER OUTPUT terminals
3 Fix the hex screw again to secure the conductor.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER SYSTEMS
Make sure to comply with the following notes:
For KS-AR8004D:
• Be sure not to connect the “·” terminals of the speakers to a common point.
• If the same lead is used for both left/right or front/rear speaker wirings, this unit cannot be used.
Always use independent leads for each speaker. In this case, redo the wiring.
• Use speakers with an impedance of 2 Ω to 8 Ω (4 Ω to 8 Ω: when used in Bridge Mode).
• Use speakers which have sufficient capacity for the unit.
When you connect 4 speakers to the unit, down mixed signals (front and rear) are emitted
through the PRE OUT jacks.
For KS-AR8002D:
Incoming signals are emitted through the PRE OUT jacks.
SPEAKER CONNECTIONS
Connection varies depending on the number of the speakers used in your car. Select the
appropriate connection referring to the following diagrams.
Connect the Line Output from the receiver to the INPUT jacks on this unit using RCA pin
cords (not included with this unit).
Before connecting:
• Be sure to adjust the CROSSOVER filter switch as illustrated on the following diagrams. (See
also “CONTROLS” on page 3.)
• Securely connect all the parts. If the connections are loose, due to contact resistance etc., heat
will break out and may cause an accident. Secure and cover the cords with insulating tape and
run them under the car mats.
Note
Do not adjust the CROSSOVER filter switch while the unit is turned on.
KS-AR8004D
KS-AR8002D
2-speaker system
Line Out
4-speaker system
Line Out (Rear)
Front Speaker Rear Speaker
JVC car receiver, etc.
JVC car receiver, etc.
(left/right)
(left/right)
Left speaker
Right speaker
Line Out
(Front)
CROSSOVER
fi lter switch
CROSSOVER
fi lter switch
Control panel
Control panel
2-speaker system (2 amplifiers)—Bridge Mode*2
2-speaker system plus subwoofer—Bridge Mode*2
Right speaker
Line Out (Rear) or Subwoofer Out
JVC car receiver, etc.
Line Out
Front Speaker
(left/right)
Line Out
Subwoofer
JVC car receiver, etc.
(Front)
Left speaker
CROSSOVER filter switch
Control panel
CROSSOVER
fi lter switch
Control panel
Control panel
2-speaker system—Bridge Mode*2
Line Out
Front Speaker
(left/right)
Subwoofer system (5.1channel receiver)—Bridge Mode*2
JVC car receiver, etc.
Subwoofer Out
JVC car receiver, etc.
CROSSOVER
fi lter switch
Subwoofer
CROSSOVER
fi lter switch
Control panel
Control panel
4-speaker system plus subwoofer (PRE OUT)
Down mixed signals are emitted through the PRE OUT jacks.
2-speaker system plus subwoofer (PRE OUT)
Line Out (Rear)
JVC car receiver, etc.
Line Out
Line Out (Front)
Front Speaker Rear Speaker
JVC car receiver, etc.
(left/right)
(left/right)
Left speaker
Right speaker
CROSSOVER
fi lter switch
CROSSOVER
fi lter switch
Control panel
Control panel
Subwoofer
System
JVC power amplifier:
KS-AR8001D
Subwoofer
System
JVC power amplifier:
KS-AR8001D
1
2
*
*
RCA pin cords (not included with this unit)
Bridge Mode: Be sure to connect the line output from the receiver to the left (L/MONO) jack on this unit.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
TROUBLESHOOTING
To operate the following controls, detach the control cover. Attach it again after operation.
For more details, consult your “JVC IN-CAR ENTERTAINMENT” car audio dealer.
The Status lamp does not light.
• Change the fuses if the current one is blown.
• Confirm the connections for the power supply (see “POWER SUPPLY” on page 1).
• Connect the ground lead securely to a metal part of the car.
• Turn on the equipment connected to this unit.
Control cover
• Use a relay if your system employs so many amplifiers.
• Confirm the battery voltage (11 V to 16 V).
The Status lamp lights in red and/or the unit heats up abnormally.
• Use speakers of a suitable impedance.
• Correct the speaker wirings if they are short-circuited.
• Leave the unit turned off for a while to cool it down.
The illustration above is for KS-AR8004D.
KS-AR8004D
The Status lamp lights in violet frequently. (Clipping*)
• Lower the input level with the Input LEVEL controller until the lamp lights in violet a few times.
* It means that the amplifier circuits are overloaded and the sound may distort due to too much
input from the car receiver.
No sound is heard.
• Confirm the connections for the power supply (see “POWER SUPPLY” on page 1).
• Connect the RCA pin cords to the INPUT jacks.
• Confirm the speaker wirings and the position of the CROSSOVER filter switch (See “SPEAKER
CONNECTIONS” on page 2).
Alternator noise is heard.
• Keep the leads of the POWER terminals away from the RCA pin cords.
• Keep the RCA pin cords away from other electrical cables in the car.
• Connect the ground lead securely to a metal part of the car.
• Make sure the negative speaker leads do not touch the car chassis.
• Replace the plugs or use plugs with load resistors.
• Connect a bypass capacitor across the accessory switches (horn, fan, etc.).
KS-AR8002D
Noise is made when you connect the unit to an AM (MW/LW) tuner.
• Move all the leads of this unit away from the antenna (aerial) lead.
SPECIFICATIONS
Maximum Power Output
RMS Power Output
600 W
KS-AR8004D: 120 W RMS x 4 channels at 4 Ω and ≤ 1% THD + N
KS-AR8002D: 150 W RMS x 2 channels at 4 Ω and ≤ 1% THD + N
Load Impedance
4 Ω
(Normal mode: 2 Ω to 8 Ω allowance)
(Bridge Mode: 4 Ω to 8 Ω allowance)
5 Hz to 40 kHz* (+0, –3 dB)
* Subsonic filter cuts off extremely low frequency signals less than
Status lamp
The lamp normally lights in blue while the unit is turned on.
Frequency Response
•
•
•
When the lamp does not light
When the lamp lights in red
When the lamp lights in violet frequently
18 Hz.
Input Sensitivity/Impedance
Distortion
2 V /44 kΩ (0.3 V to 6 V, variable)
Less than 0.01% (at 1 kHz)
80 dBA (reference: 1 W into 4 Ω)
DC 14.4 V (11 V to 16 V allowance)
Negative ground
250 mm × 62 mm × 182 mm
KS-AR8004D: 2.8 kg
KS-AR8002D: 2.6 kg
– It indicates there may be a problem. See “TROUBLESHOOTING” on the right column.
BASS BOOST controller
Turning this boosts the 45 Hz frequency within the range of 0 dB to +18 dB. Adjust the level
while listening to the sound. This control is preset to MIN when the unit is shipped.
Signal-to-Noise Ratio
Power Requirement
Grounding system
Dimensions (W×H×D)
Mass (approx.)
Input LEVEL controller
The input level can be adjusted with this control when this unit is connected to other source
equipment. Adjust the level while listening to the sound. This control is preset to MIN when
the unit is shipped.
Accessories
Screw (φ 4 × 20 mm) × 4
CROSSOVER frequency controller
Turning this adjusts the cutoff frequency within the range of 30 Hz to 500 Hz. Adjust the level
while listening to the sound. This control is preset to 30 Hz when the unit is shipped.
Hex Screw (M4 × 10 mm) × 8
Hex wrench
4 mm × 1
3 mm × 1
Spacer × 4
Bracket
CROSSOVER filter switch
OFF: Normally, set to this position. The switch is preset to this position when the unit is
shipped.
LPF: Set to this position when you want to turn on the LPF (Low-Pass Filter) switch (the
Low-Pass Filter transmits frequencies lower than the cutoff frequency).
HPF: Set to this position when you want to turn on the HPF (High-Pass Filter) switch (the
High-Pass Filter transmits frequencies higher than the cutoff frequency).
L × 4
I × 4
Design and specifications are subject to change without notice.
Information for Users on Disposal of Old Equipment
This symbol indicates that the product with this symbol should not be
disposed as general household waste at its end-of-life. If you wish to
dispose of this product, please do so in accordance with applicable
national legislation or other rules in your country and municipality. By
disposing of this product correctly, you will help to conserve natural
resources and will help prevent potential negative effects on the
environment and human health.
This symbol is only valid in the European Union.
Dear Customer,
This apparatus is in conformance with the valid European directives and standards regarding
electromagnetic compatibility and electrical safety.
European representative of Victor Company of Japan, Limited is:
JVC Technology Centre Europe GmbH
Company name changed in:
JVC Technical Services Europe GmbH
Postfach 10 05 52
61145 Friedberg
Germany
3
Download from Www.Somanuals.com. All Manuals Search And Download.
|