Assembly Procedures
VCS501 Series
Tools Required: Knife or scissors, Phillips or Robertson (square head) screwdriver, 7/16” and 3/8” wrench
or ratchet. The use of a manual screwdriver is strongly recommended. A power drill may cause damage to
the unit.
CAUTION: This grill is intended ONLY to be used as a cart model, this grill cannot be built into an
enclosure.
CAUTION: The assembly of this grill requires two (2) people.
WARNING: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly,
lifting or moving the grill is recommended. Protective eyewear and long sleeves are also strongly
recommended.
30005436 3/11 Rev. 3 En
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Step 2a: Install the Casters
This step requires ꢀ people.
Parts Required:
(4) Casters (ꢀ with brake, rear; ꢀ without brake, front)
(1) Block (not included)
(16) 1/4-ꢀ0 Flange Nut (30005406)
Figure 1
NOTE: Casters (wheels) may differ from those shown in the illustration depend-
ing on the model you purchased.
Select a side to begin installing the casters. Place a block of wood, thick tele-
phone book or anything else available - approximately 6 inches thick - under the
side to support the weight of the barbecue. Insert the four (4) bolts attached on
the casters into their respective holes located on the bottom, near the front. If you
have any difficulty snapping them into place, try rotating the casters in a circular
motion.
As one person holds the front caster in place, the other opens the front
door and installs four (4) flange nuts. Tighten the flange nuts on
the front caster. Repeat this process with the rear caster.
When both casters are in place on one side, repeat the
same procedure on the opposite side.
B346
Rear Caster
w/Brake
Blocking
Front Caster
without Brake
Figure 1
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or mov-
ing the grill is recommended.
30005436
3
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Step 2b: Attach Skirt (Optional)
Figure 2
Parts Required:
Leveling
Glide
(1) Skirt Left Assembly
(1) Skirt Right Assembly
(1) Skirt Front Assembly
(ꢀ) Skirt Corner Assemblies
(7) #10-ꢀ4 x 1/ꢀ” Screws (50000337)
(4) Adjustable Leveling Glide
Skirt Right Assembly
Skirt Left Assembly
Skirt Front Assembly
B157
Figures 2 & 3
NOTE: Remove protective coating from corner posts
before proceeding with this step.
Leveling
Glide
Screw-in two (ꢀ) adjustable leveling glides into hex
threaded insert provided in front skirt assembly.
Inverted View
Screw-in one (1) adjustable leveling glide into hex
threaded insert provided in left and right skirt assem-
blies.
Attach left skirt assembly to the unit:
Figure 3
– Loosen one hex bolt from corner post. (Refer to Corner Post
Detail)
– Slide left skirt assembly between bottom panel and
side panel.
– Secure left skirt assembly with two (ꢀ) #10-
ꢀ4 x 1/ꢀ” screws.
– Tighten hex bolt at the back of the
unit.
Repeat these steps for right side.
NOTE: If you have any problems sliding the
skirt assembly (left or right), loosen four (4)
screws on side panel and lift the side panel to
allow more space.
Slide two (ꢀ) skirt corner assemblies into the
front skirt assembly. Slide above assembly
into attached left and right skirt assemblies.
Secure all skirt assembly parts with three (3)
#10-ꢀ4 x 1/ꢀ”
screws.
B347
#10-ꢀ4 x 1/ꢀ”
Screws
Loosen Outer Bolt
at Back Side
Skirt Left
Corner Post/Skirt Detail
Assembly
Skirt Front
Assembly
Skirt Corner Assembly
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or
moving the grill is recommended.
30005436
4
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Step 3: Grease Pan / Grease Cup Installation
Parts Required:
(1) Grease Pan
(1) Grease Cup
Figure 4
Install grease pan from back side of unit. NOTE: Be sure the grease tray is posi-
tioned with the opening in the bottom of the grease tray located over the grease
cup.
Place grease cup into grease cup holder attached to bottom of left brace support.
Figure 4
Grease
Shown with optional skirt
Tray
Grease
Cup
B159
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or mov-
ing the grill is recommended.
30005436
5
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Parts Required for Steps 4, 5, 6 & 7
Right Side Shelf
Left Side Shelf
(1) Kit Condiment Tray*
(1) Kit Shelf Right**
(1) Kit Condiment Tray*
(1) Kit Shelf Left***
*Kit Condiment Tray Contents
(1) Condiment Tray Left
(1) Condiment Tray Right
(ꢀ) Towel Bars
(3) Utensil Hooks
**Kit Shelf Right Contents
(1) Shelf Right Assy w/Support Brackets
(1) Cover Side Burner Assy
(1) Side Burner Assembly
***Kit Shelf Left Contents
(1) Shelf Left Assy w/Support Brackets
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or
moving the grill is recommended.
30005436
6
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Steps 4 & 5: Right & Left Side Shelf Assembly
Parts Required:
(1) Kit Condiment Tray
(1) Condiment Tray Left
(1) Condiment Tray Right
(1) Hardware Bag Side Shelves (for both right and left side shelves)
(1) Kit Shelf Right
(1) Shelf Right Assy w/Support Brackets, Cover and Side Burner Assembly installed
(1) Kit Shelf Left
(1) Shelf Left Assy. w/Support Brackets
Figure 5
Left Side Shelf
Loosen two (ꢀ) screws on the support front of the left shelf assembly.
Slide the front condiment tray into the gap between front support and the side panel as
shown.
Tighten the two (ꢀ) screws loosened earlier.
Repeat for right side shelf.
Figure 5
Right Side Shelf Assembly
(Cover and side burner as-
sembly not shown)
Left Side Shelf
Assembly
Right Side Shelf
Left Side Shelf
Loosen Screws
From Inside
Loosen
Screws
From Inside
Bꢀ17
Condiment Tray Right
Condiment Tray Left
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or mov-
ing the grill is recommended.
30005436
7
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Step 6: Attach Right Shelf Assembly to Grill
Parts Required:
Right Shelf Assembly
(1) Right Shelf Assy. (Step 4)
(4) 1/4-ꢀ0 x 1Z\x” Screws (50001383)
(ꢀ) #10-ꢀ4 x 1/ꢀ” Screws (50000337)
Figures 6 & 7
Loosely screw in (4-5 turns) four (4) 1/4-ꢀ0 x 1Z\x” screws to the side of the grill.
Place right shelf assembly onto screws.
NOTE: Ensure the side burner ignitor wire is not pinched as the shelf assembly is installed into the unit.
Secure (tighten) four (4) screws to the grill.
Secure condiment tray to the console with one (1) #10-ꢀ4 x 1/ꢀ” screw.
From inside grill, attach 10-ꢀ4 x 1/ꢀ” screw to the right shelf assembly.
Figure 6
NOTE: Shown without
side burner.
1/4-ꢀ0 x 1Z\x” Screw
(50001383)
B348
10-ꢀ4 x 1/ꢀ” Screw
(50000337)
Figure 7
10-ꢀ4 x 1/ꢀ” Screw
(50000337
B349
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or
moving the grill is recommended.
30005436
8
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Step 7: Attach Left Shelf Assembly to Grill
Parts Required:
Left Shelf Assembly
(1) Left Shelf Assy. (Step 5)
(4) 1/4-ꢀ0 x 1Z\x” Screws (50001383)
(ꢀ) #10-ꢀ4 x 1/ꢀ” Screws (50000337)
Figure 8
Loosely screw in (4-5 turns) four (4) 1/4-ꢀ0 x 1Z\x” screws to the side of the grill.
Place left shelf assembly onto screws.
Secure (tighten) four (4) screws to the grill.
Secure condiment tray to the console with one (1) #10-ꢀ4 x 1/ꢀ” screws.
From inside grill, attach 10-ꢀ4 x 1/ꢀ” screw to the left shelf assy.
Figure 8
#10-ꢀ4 x 1/ꢀ” Screws
(50000367)
Bꢀꢀ9b
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or mov-
ing the grill is recommended.
30005436
9
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Step 8: Attach Towel Bars, Utensil Hooks and Spit Rod Storage Brackets
Parts Required
Left Side
(1) Towel Bar
Right Side
(1) Towel Bar
(3) Utensil Hooks
(4) #10-ꢀ4 x 1/ꢀ” Screws (50000337)
(4) #10-ꢀ4 x 1/ꢀ” Screws (50000337)
Spit Rod Storage Bracket
(ꢀ) Brackets (300054ꢀ7)
Towel Bars and Utensil Hooks
Figure 9
Slide three (3) utensil hooks into the towel bar. (Left side only)
Attach towel bar with utensil hooks to left side condiment tray as shown using four (4)
#10-ꢀ4 x 1/ꢀ” screws.
Attach towel bar without utensil hooks to right side condiment tray.
Spit Rod Storage Brackets
Figure 10
The spit rod storage brackets are located on the back upper panel of the grill.
Tilt the bracket as shown, so the larger end of the bracket will fit
into the opening. Then slide the bracket down. Repeat for both
brackets.
Figure 10
Figure 9
Spit Rod Storage
Bracket
Bꢀꢀ4
#10-ꢀ4 x
1/ꢀ” Screws
(50000337
Towel
Bar
Spit Rod
Storage
Utensil Hooks
B351
Rear View
Shown with optional skirt
Bꢀꢀ5
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or
moving the grill is recommended.
30005436
10
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Step 9: Attach Side Burner Assembly
Follow Side Burner Assembly Instructions to assemble side burner to unit.
Step 10: Install the Ignitor Battery
Figure 11
NOTE: VCS501 Series require one (1) “AA” bat-
tery.
Figure 11
Unscrew the ignition button from the console and
insert the appropriate battery into the housing by
placing the positive side of the battery first. Then
screw the ignition button back into the console.
Check for sparks under each main burner before
proceeding.
B35ꢀ
Step 11: Install the Backlighting Batteries
NOTE: Eight (8) “AA” batteries are required. (Not included)
Figures 12
Remove the battery case from the battery holder. Insert the eight (8) “AA” batteries.
Attach battery case to back light wire connection. Reinstall battery case in battery
holder with back light connector on the top.
WARNING: Replacing the battery incorrectly might result in an explosion. Replace
the battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to your local envi-
ronmental guidelines.
Battery
Case
Figure 12
B353
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or mov-
ing the grill is recommended.
30005436
11
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Step 12: Install the Internal Components
Parts Required:
(5) Sear Plates
(4) Cooking Grates
(1) Warming Rack
(1) Smoker Box Assy
Figures 13, 14 & 15
Carefully place each of the sear plates side by side inside the barbecue. (Fig. 13) Make sure the semicircu-
lar finger groove is facing toward the front of the grill. Each sear plate rests just above each burner tube.
NOTE: Place the smoker box assembly on any sear plate by laying the bracket over the sear plate so the
‘z’ ends of the bracket fit into the ‘z’ slots of the sear plate. Slide the smoker box assembly back into the
locked position. (Fig. 14) Continue placing the remaining sear plates. The smoker box may be left in place
when not being used. CAUTION: Only add wood chips to the smoker box when grill is cool.
Figure 13
Figure 14
Sear Plate
‘Z’ End
Smoker Box
Sear Plate
Bꢀ15a
Bꢀꢀ6
Cooking Tips - Smoker Box
• To produce more smoke and prevent fast burning, pre-soak the wood chips in a separate
bowl of water for at least ꢀ0 minutes.
• To add wood chips before cooking, fill the smoker box with your choice of flavored chips
(remove wood chips from water first). The amount and type of wood you use is entirely up
to you. Once the box is filled with the desired amount, close the lid and place the cooking
grids in the proper position on the grill.
• Tips: Small wood chips work best inside the wood chip box.
• Allow grill to heat up before placing your food on the grill. This will allow time for the wood
chips to begin to smoke.
• Do not use resinous woods such as pine or plywood. These will produce an unpleasant
flavor.
• Do not try to add more wood chips while cooking. It is recommended that you allow grill to
cool before replacing wood chips or handling the cooking grates which may still be hot.
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or
moving the grill is recommended.
30005436
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Step 12: Install the Internal Components (continued)
Set the cooking grates, side by side, on the upper ledge of the grill tub. (Fig. 15) Make sure the finger
groove is facing toward the front of the grill.
Set the warming rack into the supports located on either side of the rear lid.
CAUTION: Do not attempt to turn the cooking grates over while the grill is in use and the grates are hot.
Doing so could result in severe burns and other injuries.
Figure 15
Warming Rack
Cooking
Grates
B356
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or mov-
ing the grill is recommended.
30005436
13
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Step 13: Install the LP Cylinder
(LP Models ONLY)
Parts Required:
(1) LP Gas Cylinder (not included)
Figures 16 & 17
NOTE: Check your User’s Manual for the cylinder filling requirements, how to attach the regula-
tor and how to test for leaks before you try lighting the grill.
CAUTION: Make sure the hose is not touching any hot or sharp surfaces.
Place the LP Cylinder into the hole in the bottom panel. Next secure it from moving by lifting the
cylinder retainer wire and latching the bent edge over the lip of the cylinder.
The final step is to connect the regulator to the cylinder.
CAUTION: Do not turn on/ignite the grill until after performing a leak check at all gas connection
points and fittings. With the main LP cylinder valve OPEN, and ALL CONTROL KNOBS FULLY
OFF, use a spray solution of 50% liquid soap and 50% water onto all gas connection points and
fittings. The formation of bubbles indicates an air leak that must be repaired and verified with
this leak test before the grill is ignited.
NOTE: Ensure all plastic coatings have been removed from all stainless steel parts before using
the grill.
Figure 16
Figure 17
B359
B358
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or
moving the grill is recommended.
30005436
14
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Step 14: Install the Natural Gas Hose
(Natural Gas (NG) Models ONLY)
Figure 18
Run natural gas hose through bushing provided in back panel of grill.
Figure 18
Bꢀ40a
Shown with Op-
tional Skirt in Place
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or mov-
ing the grill is recommended.
30005436
15
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
Step 15: Install Shelf Light
Parts Required:
(1) Cook Light
(3) #10-ꢀ4 x 1/ꢀ” Screws (50000337)
Figure 19
Figures 19, 20 & 21
Attach the cook light to the side shelf using three (3) screws provided.
(Fig. 19)
Battery Installation (3 “AA” alkaline batteries required, not included.)
Open the battery cap by turning the cap counterclockwise as shown in
Figure ꢀ0. Insert the batteries into the battery compartment according to
the layout in Figure ꢀ0. Replace battery cap.
Operating Instructions
To turn the light ON and OFF, press the ON/OFF button located on the
back of the cook light. (Fig. ꢀ0)
To adjust the cook light, simply move the flexible arm as desired to
achieve the best lighting for your task.
Screws
After use, allow the light and grill to cool completely. Place the light face
down on the shelf after use and for storage. (Fig. ꢀ1) Replace the grill
cover. If a grill cover is not used, the light should be removed when not in
Bꢀ08a
use as rain, snow, etc. could damage the light.
Battery Cap
To Open
WARNING: The light may get hot when in close proximity to
the grill surface. Do not touch the light lens when in opera-
tion. Allow it to cool.
Figure 20
WARNING: Keep the light away from flammable materials.
CAUTION: Do not move the cook light directly over the
cooking area when the grill is on, as this may damage the
Flexible
Arm
cook light.
Cook Light Handle
NOTE: The light will not work until the batteries are installed.
NOTE: For optimum battery life and to avoid damage to the
light, we recommend you retract and turn off the light when not
in use.
Bꢀ09
ON/OFF Button
WARNING: Replacing the battery incorrectly might result in an
explosion. Replace the battery only with the same or equivalent type
recommended by the manufacturer. Dispose of used batteries according
to your local environmental guidelines.
Figure 21
Bꢀ3ꢀa
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or
moving the grill is recommended.
30005436
16
Download from Www.Somanuals.com. All Manuals Search And Download.
VCS501 Series Assembly
30005436
17
Download from Www.Somanuals.com. All Manuals Search And Download.
MHSC
149 Cleveland Drive • Paris, Kentucky 40361
Download from Www.Somanuals.com. All Manuals Search And Download.
|