19" LCD TV
OWNER'S MANUAL
PLV3619-DVI 'Venturer'< Manual-English >
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
WARNING: TO REDUCE THE RISK OF ELECTRIC
CAUTION
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNITTO RAIN
OR MOISTURE. DO NOT PLACE OBJECTS
FILLED WITH LIQUIDS ON OR NEAR THIS
UNIT.
RISQUE DE CHOC ÉLECTRIQUE NE
PAS OUVRIR
AVIS
* SEE REAR OF UNIT FOR GRAPHIC SYMBOLS *
The lightning flash with an arrowhead within a
triangle alerts you to uninsulated dangerous
voltage within the product's enclosure that could
cause an electric shock.
CAUTION: DANGER OF EXPLOSION IF
BATTERY IS INCORRECTLY REPLACED. REPLACE
ONLY WITH THE SAME OR EQUIVALENT TYPE.
The exclamation point within a triangle alerts
you to the presence of important operating,
maintenance and servicing instructions in this
user’s manual.
The symbol for Class II
(Doublelnsulation)
PLACEMENT INFORMATION
• Do not use this unit in places which are extremely hot, cold, dusty, or humid.
• Do not restrict the air flow of this unit by placing it somewhere with poor air flow, by covering
it with a cloth, or by placing it on bedding or carpeting.
SAFETY INFORMATION
• When connecting or disconnecting the AC cord, grip the plug and not the cord itself. Pulling
the cord may damage it and create a hazard.
• When you are not going to use the unit for a long period of time, disconnect the AC cord.
CONDENSATION INFORMATION
• When left in a heated room where it is warm and damp, water droplets or condensation may
form inside the unit. When there is condensation inside the unit, the unit may not function
normally. Let the unit stand for 1-2 hours before turning the power on, or gradually heat the
room and let the unit dry before use.
FCC INFORMATION
WARNING: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could avoid the user authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Shielded cables must be used with this unit to ensure compliance with the Class FCC limits.
WARNING: Should any problems occur, disconnect the AC cord and refer servicing
to a qualified technician.
2
PLV36190_ib_eng_1-14_wDVI.pmd
2
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
13. Unplug this apparatus during
lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such as
power-supply cord or plug is
damaged, liquid has been spilled or
objectshavefallenintotheapparatus,
the apparatus has been exposed to
rain or moisture, does not operate
normally, or has been dropped.
9. Do not defeat the safety purpose of
the polarized or grounding-type
plug. A polarized plug has two blades
with one wider than the other. A
grounding type plug has two blades
and a third grounding prong. The
wide blade or the third prong are
provided for your safety. If the
provided plug does not fit into your
outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly
at plug, convenience receptacles,
and the point where they exit from
the apparatus.
11. Only use attachments/accessories
specified by the manufacture.
12. Use only with the cart,
stand, tripod, bracket,
or table specified by the
manufacturer, or sold
with the apparatus.
When a cart is used, use caution
when moving the cart/apparatus
combination to avoid injury from
tip-over.
3
PLV36190_ib_eng_1-14_wDVI.pmd
3
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SAFETY PRECAUTIONS ...................................................................................... 2
IMPORTANT SAFETY INSTRUCTIONS .............................................................. 3
REMOTE CONTROL ........................................................................................... 5
ACCESSORIES ...................................................................................................... 5
REMOTE CONTROL REFERENCE GUIDE .......................................................... 6
UNIT REFERENCE GUIDE ................................................................................. 7
CONNECTIONS ........................................................................................... 8 – 13
Connecting a TV antenna/Cable/Satellite .................................................... 8
Connecting to A/V devices (VCR, Camcorder, Game System, etc.)
.............................................................................................................. 9 – 10
Connecting a high-definition (HD) source ............................................... 11
Connecting an audio amplifier .................................................................. 11
Connecting a PC ........................................................................................ 12
Connecting to sources with DVI output (DVD - only 480i, 480p, 720p & 1080i
are supported) ........................................................................................... 12
Connecting the power cord ...................................................................... 13
INSTALLATION ...........................................................................................13 – 14
Removing the base stand .......................................................................... 13
Mounting on the wall ................................................................................ 14
USING HEADPHONE ........................................................................................ 14
TV SETUP ................................................................................................... 15 – 19
Main menu ................................................................................................ 15
Picture menu ............................................................................................. 15
Sound menu ................................................................................................ 16
Setup menu ............................................................................................... 16
Parental setting .................................................................................. 17 – 18
TV setting .................................................................................................. 19
MTS setting ................................................................................................ 19
Restore setting ........................................................................................... 19
TROUBLE SHOOTING GUIDE ......................................................................... 20
4
PLV36190_ib_eng_1-14_wDVI.pmd
4
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
USING THE REMOTE CONTROL
•
•
Point the remote control at the REMOTE SENSOR located on the unit.
When using this unit in very bright light, the infrared REMOTE CONTROL SENSOR may not
work properly.
•
The recommended effective distance for using the remote control is about 16 feet (5 meters).
TO CHANGE THE REMOTE CONTROL BATTERY
1. Open the battery door.
2. Insert two “AAA” batteries.
BATTERY REPLACEMENT
When the batteries become weak, the operating distance of the remote control will be greatly
reduced and you will need to replace the batteries.
Note:
• If the Remote Control is not going to be used for a long time, remove the batteries to avoid
damage caused by battery leakage corrosion.
• Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or
rechargeable (NICKEL-CADMIUM) batteries.
WARNING: Do not dispose of batteries in a fire or they may leak and/or explode.
ACCESSORIES
PLEASE LOCATE THE INCLUDED ACCESSORIES.
•
Remote control (with battery) ............................................................................ x 1
VGA cable ...................................................................................................... x 1
Specifications and appearance are subject to change without notice.
Need More Help?
DO NOT RETURN THIS TO THE STORE
5
PLV36190_ib_eng_1-14_wDVI.pmd
5
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL REFERENCE GUIDE
6) DISPLAY button
Press to show which input you are
watching (TV Channel/AV/YUV/DVI/PC ).
1
2
10
7) SLEEP button
Sets the SLEEP timer. The unit will remain
ON for the time that is set, and will
automatically shut off afterwards.
3
8) CC button
11
12
13
Press to activate the Closed Captioning
feature. This function only works on
programs broadcasted with captions.
4
5
6
9) FORMATbutton
14
Press to select the picture format.
10) STANDBY/ONbutton
7
8
9
15
16
Press to turn ON the unit or put it in
STANDBY (OFF) mode.
11) YUV IN button
DirectlyselectYUVIN(componentvideo)
mode.
12) AV IN button
Directly selects AV IN mode.
13) LAST CH button
Press to switch repeatedly between the
last two channels displayed.
14) MUTE button
Press to turn off the sound.
1) FUNCTIONbutton
15) PICTUREbutton
Toggle between AV/YUV/DVI/PC/TV.
Select from preset screen display settings
tomatchthetypeofshowyouarewatching
(Standard, Personal, Movie, Dynamic, &
Soft).
2) TV button
Press to select TV channel mode.
3) Number (0 - 9) buttons
16) SOUNDbutton
Use to change the TV channels.
Selectfrompresetsoundsettings(Personal,
Voice, Music, Theater) to match the type
of show you are watching.
4) EXITbutton
Press to exit the menu and return directly
to normal viewing.
5) Cursor (
,
,
,
) buttons
Press to highlight selections on a menu
screen and make adjust certain settings.
MENU button
Press to display the on-screen menu.
+ CH – button
MoveCH+orCH–throughtheTVchannels.
+ VOLUME – button
Press to adjust the volume level.
6
PLV36190_ib_eng_1-14_wDVI.pmd
6
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
UNIT REFERENCE GUIDE
1) Color LCD Screen
2) STANDBY indicator
Indicates whether the unit is ON or in
STANDBY (OFF) mode.
Light On: The unit is in STANDBY.
Light Off: The unit is turned ON.
Remote Control Sensor
Do not block this sensor or remote control
will not work.
1
2
3) Removeable Stand
4) STANDBY/ONbutton
Turns the unit on and off.
5) MENU button
3
Enter the Setup menu.
6) FUNCTIONbutton
Select AV, YUV, DVI, PC or TV.
7) – VOL + controls
Adjust the volume level and highlight
selections (Left & Right) on the menu
screen.
8)
/
buttons
Select a TV channel and highlight
selections (Up & Down) on the menu
screen.
4
5
6
7
8
9) Power Cord
10) DVI Input
11) AV IN S-Video Input
12) AV IN Video Input Jack
13) AV IN Audio Input Jacks (Left/Right)
14) Audio Output Jacks (Left/Right)
15) TV Antenna Cable terminal - Coaxial TV
antenna input
16) Headphone jack
17) PC IN Audio Jack
18) PC IN MONITOR/VGA jack
19) YUV IN Component Video Inputs
(Y/PB/PR)
20) YUV IN Audio Input Jacks (Left/Right)
9
10
11 12 13 14
15
16 17 18
19 20
7
PLV36190_ib_eng_1-14_wDVI.pmd
7
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
CONNECTING A TV ANTENNA/CABLE/SATELLITE
To view television channels correctly, a signal must be received from one of the following
sources:
- An indoor or outdoor aerial antenna
- A cable system
- A satellite system
Note:
For receiving over-the-air TV broadcasts, we recommend that you use an external fixed antenna.
Should you require the use of a temporary antenna, please ensure that you purchase an antenna
with sufficient ability to receive in weak signal areas. Only when you are in close proximity
to a transmitter will a temporary antenna reproduce a signal as strongly as a fixed antenna.
Satellite, Cable, or
TV antenna cable to
TV ANTENNA
CABLE Terminal
(cable not included)
8
PLV36190_ib_eng_1-14_wDVI.pmd
8
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
CONNECTINGTO A/V DEVICES (VCR, Camcorder, Game System, etc.)
Connecting to Devices with an S-Video Output
To connect to A/V devices such as a VCR or camcorder:
- Connect to a VCR
Connect the right (red) and left (white) audio output
from the VCR to the right (red) and left (white)
input on this unit (Audio cable not included).
Connect the S-VIDEO output from the VCR to the
S-VIDEO input on this unit (S-VIDEO cable not
included).
Make sure you connect both audio and video from
the same VCR to the same input (AV IN).
Note:
Please refer to the user manual for the VCR for
more information.
- Connect to a camcorder
Connect the right (red) and left (white) audio output
from the camcorder to the right (red) and left (white)
input on this unit (Audio cable not included).
Connect the S-VIDEO output from the camcorder
to the S-VIDEO input on this unit (S-VIDEO cable
not included).
Make sure you connect both audio and video from
the same camcorder to the same input (AV IN).
Note:
Please refer to the user manual for the camcorder
for more information.
9
PLV36190_ib_eng_1-14_wDVI.pmd
9
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
Connecting to Devices with a Composite (yellow RCA-type) Video Output
To connect to A/V devices such as a VCR or camcorder:
- Connect to a VCR
Connect the right (red) and left (white) audio output
from the VCR to the right (red) and left (white)
input on this unit (Audio cable not included).
Connect the video (yellow) output from the VCR to
the video input on this unit (Video cable not
included).
Make sure you connect both audio and video from
the same VCR to the same input (AV IN).
Note:
Please refer to the user manual for the VCR for
more information.
- Connect to a camcorder
Connect the right (red) and left (white) audio output
from the camcorder to the right (red) and left (white)
input on this unit (Audio cable not included).
Connect the video (yellow) output from the
camcorder to the video input on this unit (Video
cable not included).
Make sure you connect both audio and video from
the same camcorder to the same input (AV IN).
Note:
Please refer to the user manual for the camcorder
for more information.
10
PLV36190_ib_eng_1-14_wDVI.pmd
10
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
CONNECTING A HIGH-DEFINITION (HD) SOURCE
High-Definition (HD) Devices with component video output must be connected to the YUV input:
Connect the three video outputs (Y, Pb, Pr) from the source to the corresponding video inputs on
this unit (Component video cable not included).
Connect the right (red) and left (white) audio output from the source to the right (red) and left
(white) input on this unit (Audio cable not included).
Make sure you connect both audio and video from the same source to YUV IN.
Note : When connecting a DVD player to the television, the picture resolution is solely depen-
dent upon the resolution supported by the DVD player attached. DVD Player resolutions vary from
480i to 1080i, and this television can support DVD players up to a maximum resolution of 1080i.
* May require a subscription for
receiving HD channels, check
with your cable/satellite service
provider for details.
CONNECTING ANAUDIO AMPLIFIER
This connection allows you to use an audio
amplifier and external speakers.
Connect the right (red) and left (white) audio
OUTPUT from this unit to the right (red) and left
(white) audio INPUT on your amplifier. Refer to
your amplifier’s user manual for more information.
Note :
To control the audio, both the TV and the amplifier
must be turned on, and the volume of the amplifier
must be set above 0, or you will not hear any
sound.
If you want to hear the sound from the amplifier
only. Press the Volume – button of TV to decrease
the volume or press the MUTE button of remote
control to turn off the sound.
11
PLV36190_ib_eng_1-14_wDVI.pmd
11
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
CONNECTING A PC
Connect the 15-pin D-SUB PC/VGA connector from
your computer to the 15-pin D-SUB PC/VGA input
on this unit using a monitor cable (not included).
Connect a stereo audio cable (not included) to
the PC AUDIO IN jack on the bottom of this unit,
and the other end to the AUDIO OUT jack on your
computer’s sound card.
PC IN
CONNECTINGTO SOURCES WITH DVI OUTPUT (DVD - only 480i, 480p,
720p & 1080i are supported)
Connect the output from your HD source to the
DVI input on this unit. Connect a stereo audio
cable (not included) to the PC AUDIO IN jack on
the bottom of this unit, and the other end to the
AUDIO OUT jack on your HD source.
To operate the connected device, first press the
FUNCTION button to select the DVI IN mode.
Using in HD (High Definition) Mode
The HD (High Definition) mode allows you to
enjoy clearer and sharper pictures through the
AUDIO
MONITOR
VGA
PC IN
DVI inputs if you are using a HD source.
DVI IN
DVI
12
PLV36190_ib_eng_1-14_wDVI.pmd
12
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
CONNECT THE POWER CORD
• Connect the AC power cord into a wall outlet.
• Press the STANDBY/ON button on the top of unit
or remote control to turn on the unit.
Note:
• Be sure the AC power cord is disconnected and
all functions are off before making connections.
• Make sure that all the components are connected
correctly.
• To prevent electrical shock, match wide blade
of plug to wide slot, and fully insert.
• When you are not going to use the unit for a long
period of time, disconnect the power cord.
To AC outlet
INSTALLATION
REMOVINGTHE BASE STAND
WARNING: The LCD Display is very fragile, and must be protected at all times when removing
the base stand. Be sure that no hard or sharp, or anything that could scratch or damage the LCD
display, come in contact with it. Do NOT place pressure on the rear of the unit at any time
because the screen could crack.
1. Disconnect any cables or cords connected to the unit.
2. Lay the unit down on a flat surface, so the back side is facing up, making sure to place a
soft cushioned material (such as a pillow or thick piece of foam) beneath the screen.
3. Remove the four screws and then remove the BASE STAND from the TV.
13
PLV36190_ib_eng_1-14_wDVI.pmd
13
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
MOUNTING ONTHEWALL
This unit is VESA-compliant, and is designed to be wall-mounted with a VESA-compliant 3.9” x
3.9” (100mm x 100mm) mounting kit designed for flat-panel TVs (sold separately). Mount this
unit according to the directions included with the mounting kit.
3.9”
USING HEADPHONES
• Turn down the volume before connecting headphones to the unit, then adjust the volume to
your desired level.
• When headphones are connected, no sound will come from the front speakers.
Note:
• Avoid listening to sound at high levels for prolonged periods of time. This may be harmful to
you and may cause hearing loss.
14
PLV36190_ib_eng_1-14_wDVI.pmd
14
18/01/2007, 17:01
Download from Www.Somanuals.com. All Manuals Search And Download.
TV SETUP
MAIN MENU
1. Press the MENU button.
2. Use the
or
button to select the options (Picture / Sound
/ Setup / TV Setting / Restore Setting).
3. The screen will change to your selected mode immediately.
4. To exit the MAIN MENU and return to the normal screen, press
the EXIT button on remote control.
NOTE: When you are in PC, AV IN, YUV IN & DVI IN mode, the TV
Setting option will not be shown.
PICTURE MENU
1. Press the MENU button.
2. Use the
or
button to select the Picture menu, then press the
button to confirm the
setting.
3. Use the
or
button to select the options (Brightness, Contrast, Color, Sharpness, Hue,
Color Temp, Mode) and adjust them using the
or
buttons. (The screen will change to
your desired setting).
4. Repeat step 3 to adjust other options.
5. To exit the MAIN MENU and return to the normal screen, press the EXIT button on remote
control.
TV / AV MODE
•
•
Brightness : Adjust to brighten the darkest parts of the picture.
Contrast
: Adjust to sharpen the picture quality. The black
portions of the picture become richer in darkness
and the white become brighter.
•
•
Color
: Adjust the color of the picture.
Sharpness : Adjust the sharpness level to improve detail in
the picture.
•
•
Hue
: Adjust the hue of the picture. (Toward purple /
Toward green)
YUV / DVI MODE
ColorTemp : Adjust the three color temperature of the picture.
Select Normal (balanced) / Cold (blue white) /
Warm (red white) mode.
•
Mode
: Select from preset screen display settings to match
the type of show you are watching (Standard,
Personal, Movie, Dynamic, & Soft).
In PC mode
PC MODE
Use the
or
button to select the options (Brightness, Contrast,
Frequency, Phase, H offset, V offset, Auto config, Color Temp,
Mode) and adjust them using the or buttons. (The screen will
change to your desired setting).
-
-
Resolution
Refresh Frequency : 70Hz max
: 1,440 x 900 max
•
•
•
H offset
V offset
: Center the image by moving it left or right.
: Center teh image by moving it up or down.
ColourTemp : Adjust the three colour temperature of the
picture. Select Normal (balanced) / Cold (blue
white) / Warm (red white) mode.
15
PLV36190_ib_eng_15-20_wDVI.pmd
15
18/01/2007, 17:03
Download from Www.Somanuals.com. All Manuals Search And Download.
TV SETUP
SOUND MENU
1. Press the MENU button.
2. Use the
setting.
or
button to select the Sound menu, then press the
button to confirm the
3. Use the
or
button to select the options (Bass, Treble, Balance, Mode) and adjust them
using the
or
buttons.
4. Repeat step 3 to adjust other settings.
5. To exit the MAIN MENU and return to the normal screen, press the EXIT button on remote
control.
TV / AV / YUV / DVI /
PC MODE
Note:
Experiment with different sound settings until you find the settings
you prefer.
• Bass
: Adjust the bass range.
• Treble : Adjust the treble range.
• Balance : Adjust the balance level toward the left or right
speakers.
• Mode
: Select from preset sound settings (Personal, Voice,
Music, Theater) to match the type of show you are
watching.
SETUP MENU
1. Press the MENU button.
2. Use the
setting.
or
button to select the Setup menu, then press the
button to confirm the
3. Use the
or
button to select the options (OSD Size, Language, Parental, Timers) and
or buttons.
adjust them using the
4. Repeat step 3 to adjust other settings.
5. To exit the MAIN MENU and return to the normal screen, press the EXIT button on remote
control.
TV / AV MODE
Notes:
•
•
•
OSD Size : Select the screen size you prefer.
Language : Select from English / Français / Español.
Parental : Sets the parental controls. Refer to the section
titled “PARENTAL SETTING” for instructions.
•
Timers
: Select the Sleep timer / Reminder timer mode :
Off -> 5 - - - - -> 115 -> 120.
Sleep timer : Set the LCD TV to turn itself off
within a certain time.
Reminder timer : Remind the show time setting
of TV.
YUV / DVI / PC MODE
16
PLV36190_ib_eng_15-20_wDVI.pmd
16
18/01/2007, 17:03
Download from Www.Somanuals.com. All Manuals Search And Download.
TV SETUP
PARENTAL SETTING
LOCK CODE
1. Press the MENU button.
2. Use the
or
button to select the Setup menu, then press the
button to confirm the
or button to
setting.
3. Use the
or
button to select the Parental menu, then press the
confirm the setting and the menu locked screen will be displayed.
4. Enter a 4-digit lock code. Once entered, the screen will enter the Parental menu. The preset
lock code is “ 0000 “.
5. To exit the MAIN MENU and return to the normal screen, press the EXIT button on remote
control.
TV / AV MODE
If you forget the password,
enter “ 8 8 8 8 “ to unlock parental control.
17
PLV36190_ib_eng_15-20_wDVI.pmd
17
18/01/2007, 17:03
Download from Www.Somanuals.com. All Manuals Search And Download.
TV SETUP
PARENTAL SETTING
CHILD LOCK
1. Press the MENU button.
2. Use the
setting.
3. Use the
or
button to select the Setup menu, then press the
button to confirm the
or button.
or
button to select the Parental menu, then press the
4. Enter a 4-digit to select the Lock code and turn on/off the Child lock using
or
button.
TV / AV MODE
5. Use the
or
button to select various Parental settings and use the
or or
button to
adjust each setting.
6. Repeat steps 4-5 to adjust other options.
7. To exit the MAIN MENU and return to the normal screen, press the EXIT button on remote
control.
1. OFF
2. G
Suitable for all ages.
3. PG
SUGGESTED - Some material may
not be suitable for children.
4. PG-13
under 13.
:
GENERAL AUDIENCES,
5. R : RESTRICTED, Under 17 requires
accompanying parent or adult
guardian for viewing in movie
theaters.
6. NC-17 : No one 17 or under admitted
in movie theaters,
:
PARENTAL GUIDANCE
MPPA
Rating
:
PARENTS STRONGLY
CAUTIONED - Some material may
be inappropriate for children
7. X : Adults Only.
1. OFF
2. TV-Y
children.
3. TV-Y7
4. TV-G : General Audience.
:
Recommended for all
Recommended for all
5. TV-PG : Parental Guidance Suggested.
6. TV-14 : Parental Strongly Cautioned.
7. TV-MA : Mature Audience Only.
PG
Rating
:
children age 7 and above.
1. Violence : Contains violence.
2. Sex : Contains sexual situations.
4. Dialogue : Contains dialogue.
5. Fantasy Violence : Contains fantasy
violence.
PG
Contents
3. Language
language.
:
Contains adult
1. E : Exempt.
2. C : Children.
5. PG
:
PARENTAL
GUIDANCE
SUGGESTED - Some material may not
be suitable for children.
6. 14+ : Viewers 14 years and older.
7. 18+ : Adult Programming.
Can. Eng
3. C8 : Recommended for children age 8.
4. G GENERAL AUDIENCES,
:
Suitable for all ages.
4. 13+ : Not suitable for children under
the age of 13.
5. 16+ : Not suitable for children under
the age of 16.
1. E : Exempt.
2. G
:
GENERAL AUDIENCES,
Can.
French
Suitable for all ages.
3. 8+ : Not recommended for young
childred.
6. 18+ : Adult Programming.
18
PLV36190_ib_eng_15-20_wDVI.pmd
18
18/01/2007, 17:03
Download from Www.Somanuals.com. All Manuals Search And Download.
TV SETUP
TV SETTING
1. Press the MENU button.
2. Use the
the setting.
3. Use the
or
button to select the TV setting menu, then press the
button to confirm
or button to
or
button to select the Channel no. setting and use the
change the channel no.
4. Use the or button to select the Tuning mode and use the
AIR (over-the-air broadcasts) to CABLE (cable/satellite broadcasts).
5. Use the or button to select the Auto tune and press the or
or
button to change from
button to confirm the
selection. The unit will immediately search through all possible TV channels and store
those channels with signals in memory. After this is complete, the unit will switch to the
first channel found.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button.
Note : This option is available in TV mode only.
Remarks:
TV MODE
Channel no. : 2-69 channel for Air mode, 1-125 channel for Cable
mode.
Tuning mode : Air or Cable mode are available.
Auto tune
:
Searches for usable stations and stores them in
memory.
Skip
Fine tune
AFC
:
:
:
:
ON - Skip weak channels. OFF - No channel skip.
The frequency changes to allow fine tuning.
Auto frequency control.
Select the Mono sound/Stereo sound/Secondary
Audio Program (SAP). Refer to the section titled
“MTS SETTING” for instructions.
MTS
MTS (Multi-channel Television Sound) SETTING
This feature allows reception of sound other than the main audio for the program.
1. Press the MENU button.
2. Use the or button to select the TV setting menu, then press the
button to confirm the
setting.
3. Use the or button to select MTS menu, and press the
(Mono, Stereo, SAP)
or button to select the options
4. To exit the MAIN MENU and return to the normal screen, press the EXIT button on remote
control.
TV MODE
Note:
• MTS only operates while in TV mode.
• The SAP (Secondary Audio Programs) feature allows a TV station
to broadcast other information, which could be audio in another
language.
RESTORE SETTING
If you reset the TV to the factory settings, all your present settings on picture & sound will be
erased and replaced by the factory’s default settings. However, picture setting in PC mode and
parental setting will not be erased.
19
PLV36190_ib_eng_15-20_wDVI.pmd
19
18/01/2007, 17:03
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING GUIDE
SYMPTOM
CAUSE (AND REMEDY)
• Check that the AC power cord is connected.
• Turn on the unit.
No power.
• Remove any obstacles between the remote and the unit.
• Use the remote near the unit.
The remote does not
function.
• Point the remote at the remote sensor on the unit.
• Replace the battery in the remote with a new one.
Bad Picture (snow,
• Check the location of the antenna and adjust it if
neccessary.
multiple
images,
distortion, blurry)
• Make sure the antenna cable is connected firmly.
• Make sure all input cables are firmly connected.
No sound.
• Increase the volume.
• Check whether the mute function has been activated on
the Remote Control.
Black and white
picture.
• Check the Picture setting within the Setup menu.
•
Check to make sure the program you are watching is
broadcast in Color and not Black & White.
No picture or sound.
• Make sure the unit is plugged in and turned on.
• Make sure that the TV mode is selected.
• Try a new channel to check for possible station trouble.
• Make sure the antenna is connected properly.
• Increase the volume.
•
Make sure the antenna or audio/video source device is
working properly.
• Make sure all cables are connected firmly.
• Check for local interference.
Colored patches of
picture.
• Make sure there are no unshielded electrical devices nearby
that are causing interference.
• Turn the TV off for 30 minutes, then try it again.
Printed in China
811-361991W121
20
PLV36190_ib_eng_15-20_wDVI.pmd
20
18/01/2007, 17:03
Download from Www.Somanuals.com. All Manuals Search And Download.
|