SLH100P_ManualEN_091406 9/28/06 10:55 AM Page i
SLH100P
Hig h In te n sity Disch a rg e Sp o tlig h t
Co rd le ss • Re ch a rg e a b le
IN STRUCTIO N MAN UAL
& WARRAN TY IN FO RMATIO N
IMPO RTAN T SAFETY IN FO RMATIO N , SAVE THESE IN STRUCTIO N S
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND
THIS INSTRUCTION MANUAL. THIS MANUAL CONTAINS IMPORTANT
INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS PRODUCT.
4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312
Toll Free: (800) 544-6986
Cat. # SLH100P
SEPTEMBER ‘06
Form # 90510392
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
SLH100P_ManualEN_091406 9/28/06 10:55 AM Page 2
•
O UTDO O R USE EXTEN SIO N CO RDS. When tool is used outdoors, use only extension cords
intended for use outdoors and so marked.Safety guidelines / definitions
Minimum Gage for Cord Sets
Volts
Total Length of Cord in Feet
120V
0-25
(0-7,6m) (7,6-15,2m)
0-50 51-100
26-50
51-100
101-150
(15,2-30,4m)
101-200
(30,4-45,7m)
240V
201-300
(0-15,2m) (15,2-30,4m) (30,4-60,9m)
(60,9-91,4m)
Ampere Rating
More
Than
Not more
Than
6
10
12
American Wire Gage
0
6
-
-
18
18
16
14
16
16
16
12
16
14
14
14
12
12
10 -
12 -
16
Not Recommended
SAFETY GUIDELINES/DEFINITIONS
DAN GER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARN IN G: Indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTIO N : Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
CAUTIO N : Used without the safety alert symbol indicates potentially hazardous situation which, if not
avoided, may result in property damage.
WARN IN G: RISK O F UN SAFE O PERATIO N . When using tools or equipment, basic safety
precautions should always be followed to reduce the risk of personal injury. Improper operation,
maintenance or modification of tools or equipment could result in serious injury and property damage.
There are certain applications for which tools and equipment are designed. Vector Products, Inc. strongly
recommends that this product NOT be modified and/ or used for any application other than for which it
was designed. Read and understand all warnings and operating instructions before using any tool or
equipment.
SAVE THESE INSTRUCTIO NS
THIS MAN UAL CO N TAIN S IMPO RTAN T SAFETY AN D O PERATIN G IN STRUCTIO N S FO R
THE HID SPO TLIGHT SLH1 0 0 P.
WARN IN G: TO REDUCE THE RISK O F IN JURY:
• Follow these instructions and those published by the manufacturer of any equipment you intend to use
with this unit. Review cautionary markings on these products.
IMPORTANT SAFETY INSTRUCTIONS
WARN IN G: This product or its power cord contains lead, a chemical known to the State of
California to cause cancer and birth defect or other reproductive harm. Wash hands after handling.
WARN IN G: RISK O F ELECTRIC SHO CK: This light contains high voltage components. Do not
disassemble this light other than to replace or recycle the battery. Should this light become damaged,
immediately discontinue use and return it to an authorized service center for repair.
• This light is for dry location use only. Never expose this light to rain.
•
Do not operate light with damaged cord or plug; or if the unit has received a sharp blow, been
dropped, or otherwise damaged in any way. Evidence of tampering with the light will void the warranty.
• Do not operate this unit with a missing or damaged guard or glass lamp containment barrier.
• Do not immerse this spotlight in water. This unit is not waterproof.
WARN IN G: Risk of injury to eyes and skin from UV exposure. The glass of the bulb blocks harmful
UV radiation emitted by the bulb. Never operate the light if you suspect the bulb is cracked or see that
it is broken. Prior to each use look for evidence of bulb damage and if suspected or observed do not
use the light. Return the light to an authorized service center for repair.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SLH100P_ManualEN_091406 9/28/06 10:55 AM Page 3
• Do not look directly at lighted lamp.
• Never shine the spotlight into another person’s eyes.
• Keep sharp objects away from lens – it is glass and can break.
WARN IN G: RISK O F FIRE O R IN JURY TO PERSO N S FRO M CO N TACT W ITH HO T LEN S:
Never block the lens of this light. If the light is operated with the lens blocked, the lens will get hot and
may ignite or damage materials it contacts and it can burn the skin.
• Never place the light with the lens face-down on any surface when lit.
• Keep lamp away from materials that may burn.
• Do not touch hot lens, guard, or enclosure.
• Lens can get hot – do not touch lens while spotlight is operating.
WARN IN G: TO REDUCE THE RISK OF INJURY, THIS UNIT SHOULD ONLY BE OPERATED BY
ADULTS; IT IS NOT FOR USE BY CHILDREN.
CAUTIO N : TO REDUCE THE RISK O F IN JURY O R PRO PERTY DAMAGE:
• Charge only with originally supplied 120 volt AC or 12 volt DC charging adapters. Consult your
authorized service center for replacement.
• Replace batteries with the same size and type indicated in the Specifications in the back of this
instruction manual.
• Do not drop or throw spotlight.
• Do not crush, cut, pull or expose charging adapter cords to extreme heat or sharp edges.
• Position charging adapter cords so that they do not become entangled and away from lens so that
they do not become a safety hazard.
• Always charge in a dry location.
• Plug in the charging adapter at the spotlight first, then plug into the charging source.
• After recharge, disconnect charging adapter and wait 5 minutes before use.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SLH100P_ManualEN_091406 9/28/06 10:55 AM Page 4
TABLE O F CO N TEN TS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking your SLH100P HID Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Controls and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
120 Volt AC Charging/ Recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
12 Volt DC Charging/ Recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Using the Spotlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Using the Adjustable Work Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safe Battery Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
IN TRO DUCTIO N
Congratulations on purchasing the Pow er On Boa rd ® HID Sp otlig ht, an advanced
design that uses powerful, proven-technology, rechargeable, non-spillable, sealed, lead
acid battery for years of dependable use. It was designed to be the most versatile and
practical light for travel, camping, picnicking, tailgate parties and boating. Extremely
rugged construction protects the unit from most vibration and shock damage.
Un p a ck in g yo u r SLH1 0 0 P HID Sp o tlig h t
The following items are included in the HID Spotlight package:
WARN IN G: PLEASE
INSPECT THE LIGHT
FO R DAMAGE BEFO RE
USE. IN THE CASE THAT
DAMAGE IS FO UND,
1 2 0 VO LT AC
AN D 1 2 VO LT DC
CHARGIN G
ADAPTERS
RETURN THE LIGHT FOR
EXCHANGE.
HID SPO TLIGHT
FEATURES
• Powerful, prefocused, high intensity discharge metal halide bulb
• Replaceable 7 Amp hour sealed lead acid battery
• AC and DC recharge adapters
• LED charging indicator
• Adjustable carry strap
• Protective safety guard (bezel) around lens
• Hands-free adjustable work stand
• Automatic charging (switches to float mode once fully charged)
• Charging and full charge LED indicators
• Battery status indicator pushbutton
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SLH100P_ManualEN_091406 9/28/06 10:55 AM Page 5
Co n tro ls a n d Fu n ctio n s
PO W ER SW ITCH
ADJUSTABLE
CARRY STRAP
3 5 WATT 6 0 0 0 K
METAL HALIDE
BULB
CO N VEN IEN T
CARRY HAN DLE
BATTERY STATUS
IN DICATO R
PUSHBUTTO N
CHARGIN G AN D
FULL CHARGE
IN DICATO R
AC CHARGIN G PO RT
TO UGH, DURABLE
ADJUSTABLE
HO USIN G
W O RK STAN D
CHARGIN G THE BATTERY
The unit is delivered in a partially charged state. It must
be fully charged prior to first use by using the 120 volt
AC method.
1 2 0 VO LT AC
AN D 1 2 VO LT DC
CHARGIN G
After charging, disconnect the Adapter from the
external power source, then disconnect the Adapter
from the AC Recharge Port.
ADAPTERS
CAUTIO N: Before charging/ recharging the unit’s
battery, make sure the power switch is in the OFF position.
1 2 0 Vo lt AC Ch a rg in g / Re ch a rg in g
Plug the supplied 120 Volt AC Adapter’s plug into a standard North American
outlet. Connect the adapter’s DC pin into the AC Recharge Port located on the side
of the unit, next to the Battery Status Indicator. The Charging LED will light to indicate
that the unit is charging. The Full Charge LED indicator will light green when the unit
is fully charged.
1 2 Vo lt DC Ch a rg in g / Re ch a rg in g
The DC recharging method will NOT recharge the unit as effectively as the 120 volt
AC method. The 12 volt DC recharging procedure is recommended only when it is
necessary, since frequent use of the 12 volt DC recharging procedure may shorten
the battery system’s life.
1. Insert the end plug of the12 Volt DC Adapter plug into the vehicle’s 12 volt DC
accessory outlet.
2. Insert the DC pin in the charging port on the side of the light.
3. Charging time using this method is approximately 5 to 6 hours.
4. When charging is complete, remove the power cord.
No te : When using a vehicle’s 12 volt DC accessory outlet as a charging source,
be aware that some vehicles require the ignition be turned on to power the accessory
outlet.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SLH100P_ManualEN_091406 9/28/06 10:55 AM Page 6
O PERATIN G IN STRUCTIO N S
Usin g th e Sp o tlig h t
The HID Spotlight is operated by the switch located on the handle of the unit.
Usin g th e Ad ju sta b le Wo rk Sta n d
Set the hands-free adjustable work stand to the desired position; the stand will click
into position.
CARE AN D MAIN TEN AN CE
CAUTIO N
To re d uce th e risk o f b urn s a n d a vo id d a m a g e to th e un it, m a k e sure
a ll p o w e r sw itch e s a re in th e O FF p o sitio n , a ll a d a p te rs a re un p lug g e d
a n d th e un it h a s b e e n a llo w e d to co o l d o w n b e fo re re p la cin g th e
b a tte ry a n d p e rfo rm in g a n y ca re a n d m a in te n a n ce o n th e e x te rio r o f
th e lig h t.
All batteries lose charge with time. AC recharge is recommended after each use or
every two months when not in frequent use.
If the unit gets dirty, gently clean the outer surfaces of the Spotlight with a soft cloth
moistened with a mild solution of water and detergent. Periodically inspect the
condition of recharge adapters, connectors, and wires. Replace any components
that may have become worn or broken.
Re p la ce m e n t Pa rts
The sealed lead acid battery is the only user-replaceable part in this light and it is
available through Vector Products, Inc. These can also be purchased from popular
automotive parts suppliers nationwide. Contact Vector Products, Inc.’s Technical
Support Department for replacement parts (including replacement adapters and
cords) and any additional information that you may need. They may be reached toll
free at (800) 544-6986.
Ba tte ry Re p la ce m e n t
1. Remove screws and rotate the back cover counterclockwise.
2. Pull out and remove the battery.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SLH100P_ManualEN_091406 9/28/06 10:55 AM Page 7
3. Disconnect the terminals and replace the battery with the same type and size
listed in the Specifications section in the back of this manual.
4. Replace the battery compartment cover and screws.
5. Turn the spotlight’s ON/ OFF switch to the ON position to ensure proper
operation of spotlight.
Sa fe Ba tte ry Disp o sa l
Contains a maintenance-free, sealed, non-spillable, lead acid battery,
which must be disposed of properly. Recycling is required, contact your
local authority for information. Failure to comply with local, state and
federal regulations can result in fines, or imprisonment. For more
information on recycling this battery, call toll-free (877) 288-7722.
TRO UBLESHO O TIN G
Pro b le m
Po ssib le Ca use
Po ssib le so lutio n
• Lamp is still hot
and will not restart
immediately.
HID lamp power was
suddenly interrupted.
HID lamp can take up to 10
minutes to reach full light power
after a power interruption.
Lamp will not power. Internal battery needs
charging.
Check battery level and recharge
unit if necessary using AC or DC
charging adapters. If battery
does not take a charge, it needs
to be replaced. Contact an
•
authorized service center.
Power switch is OFF.
Unit is still charging.
Turn the power switch to the ON
position.
Disconnect recharging adapters
from unit and power source and
wait five minutes before using.
• Unit will not recharge.
DC plug is not
connected to the
vehicle.
Be sure to properly make a good
connection to vehicle’s accessory
outlet before recharging the unit.
DC plug damage
Have cord replaced by an
authorized service center.
120 VAC charging
adapter is not
connected to the
charging port
Connect 120 VAC wall cube
adapter’s barrel connector to
unit’s recharging port and then
to 120 VAC wall receptacle.
There is no power
after conncecting
to 120 volt wall
receptacle
120 volt wall receptacle circuit
tripped and needs to be reset.
If problem continues, servicing
receptacle is advised.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SLH100P_ManualEN_091406 9/28/06 10:55 AM Page 8
SPECIFICATIO N S
Spotlight:
Batteries:
6000 K 35 W Mh
12V 7Ah SLA
AC Adapter:
DC Adapter:
13.5V 750 mA
12 V
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SLH100P_ManualEN_091406 9/28/06 10:55 AM Page 9
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SLH100P_ManualEN_091406 9/28/06 10:55 AM Page 10
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SLH100P_ManualEN_091406 9/28/06 10:55 AM Page 11
O N E YEAR LIMITED WARRAN TY PRO GRAM
This limited warranty program is the only one that applies to this product, and it sets forth all the
responsibilities of Vector Products, Inc., regarding this product. There is no other warranty, other than
those described herein. Any implied warranty of merchantability or fitness for a particular purpose on
this product is limited in duration to the duration of this warranty.
This Vector Products, Inc. product is warranted, to the original purchaser only, to be free of defects in
materials and workmanship for one year from the date of purchase without additional charge. The
warranty does not extend to subsequent purchasers or users. Manufacturer will not be responsible for
any amount of damage in excess of the retail purchase price of the product under any circumstances.
Incidental and consequential damages are specifically excluded from coverage under this warranty.
This product is not intended for commercial use. This warranty does not apply to damage to units from
misuse or incorrect installation/ connection. Misuse includes wiring or connecting to improper polarity
power sources.
RETURN/ REPAIR POLICY: Defective products may be returned to manufacturer. Any defective product
that is returned to manufacturer within 30 days of the date of purchase will be replaced free of charge.
If such a product is returned more than 30 days but less than one year from the purchase date,
manufacturer will repair the unit or, at its option, replace it, free of charge.
If the unit is repaired, new or reconditioned replacement parts may be used, at manufacturer’s option.
A unit may be replaced with a new or reconditioned unit of the same or comparable design. The
repaired or replaced unit will then be warranted under the terms of the remainder of the warranty
period. The customer is responsible for the shipping charges on all returned items. During the warranty
period, manufacturer will be responsible for the return shipping charges to the customer in the United
States.
LIMITATIONS: This warranty does not cover accessories, such as charging adapters, bulbs, fuses and
batteries, damage or defects resulting from normal wear and tear (including chips, scratches, abrasions,
discoloration or fading due to usage or exposure to sunlight), accidents, damage during shipping to our
service facility, alterations, unauthorized use or repair, neglect, misuse, abuse, failure to follow
instructions for care and maintenance, fire, flood and Acts of God.
If your problem is not covered by this warranty, call our Technical Support Department toll free at (800)
544-6986 for general repair information and charges if applicable.
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations
on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential
damages, so the exclusions or limitations stated herein may not apply. This warranty gives the purchaser
specific legal rights; other rights, which vary from state to state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Technical Support by telephone, fax
or mail (see below). We suggest that you keep the original packaging in case you need to ship the unit.
When returning a product, include your name, address, phone number, dated sales receipt (or copy)
and a description of the reason for return and product serial number. After repairing or replacing the
unit, we will make every effort to return it to you within four weeks.
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector Products, Inc.
Enter “SLH100P” as Model and “High Intensity Discharge Spotlight” as Product Type. All Vector
Products, Inc. products must be registered within 30 days of purchase to activate this warranty. Mail the
completed registration form, along with a copy of the original sales receipt, to:
ATTN.: CUSTOMER SERVICE
4409 W. Wanda, McAllen, TX 78503
• TOLL FREE: (800) 544-6986 • FAX: (956) 630-0492 •
WARRANTY IS NON-TRANSFERABLE.
BD031306
© 2006 VECTOR PRODUCTS, INC.
MADE IN CHINA
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|