Vanguard Heating Indoor Fireplace VMH10TNB User Manual

®
VENT-FREE NATURAL GAS  
COMPACT CLASSIC HEARTH® FIREPLACE  
OWNER’S OPERATION AND INSTALLATION MANUAL  
VMH10TNB  
10,000 Btu/Hr with  
Thermostat  
Shown with Optional  
Cabinet Mantel/Hearth  
Base Accessory  
WARNING: Improper instal-  
WARNING: If the information in this manual  
lation,adjustment,alteration,  
is not followed exactly, a fire or explosion  
service, or maintenance can  
may result causing property damage, per-  
sonal injury, or loss of life.  
causeinjuryorpropertydam-  
age. Refer to this manual for  
correct installation and op-  
erational procedures. For as-  
sistance or additional infor-  
mation consult a qualified in-  
staller,serviceagency,orthe  
gas supplier.  
— Do not store or use gasoline or other  
flammable vapors and liquids in the  
vicinity of this or any other appliance.  
— WHAT TO DO IF YOU SMELL GAS  
• Do not try to light any appliance.  
• Do not touch any electrical switch; do  
not use any phone in your building.  
• Immediatelycallyourgassupplierfrom  
a neighbor’s phone. Follow the gas  
supplier’s instructions.  
WARNING: This is an  
unvented gas-fired heater. It  
uses air (oxygen) from the  
room in which it is installed.  
Provisionsforadequatecom-  
bustion and ventilation air  
must be provided. Refer to  
Air for Combustion and Ven-  
tilation section on page 5 of  
this manual.  
• If you cannot reach your gas supplier,  
call the fire department.  
— Installation and service must be per-  
formed by a qualified installer, service  
agency, or the gas supplier.  
This appliance may be installed in an aftermarket*, permanently located, manufactured  
(mobile) home, where not prohibited by local codes.  
This appliance is only for use with the type of gas indicated on the rating plate. This  
appliance is not convertible for use with other gases.  
*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer  
Save this manual for future reference.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
PRODUCT  
UNPACKING  
1. Remove log box and fireplace from  
carton. IMPORTANT: The fireplace  
hood is inside the cardboard protective  
end wrap on the left side of fireplace  
(as viewed from front). A decal is on  
the outside of the cardboard end wrap  
stating hood is enclosed (see Figure 2).  
IDENTIFICATION  
Fireplace  
Cabinet  
2. Remove hood from cardboard protec-  
tive end wrap as shown in Figure 2.  
Screen  
3. Remove all protective packaging ap-  
plied to fireplace for shipment.  
4. Make sure your fireplace includes one  
hardware packet.  
5. Check fireplace for any shipping dam-  
age. If fireplace is damaged, promptly  
inform dealer where you bought fireplace.  
Log  
IMPORTANT:  
Hood Enclosed  
Decal  
THIS PACKAGE CONTAINS A  
FIREPLACE HOOD. UNWRAP  
CARTON AND REMOVE HOOD  
BEFORE DISCARDING  
PROTECTIVE PACKAGING.  
Control Knob  
Ignitor Button  
Cardboard  
Protective  
Fireplace  
End Wrap  
Figure 1 - Vent-Free Natural Gas Compact Fireplace  
LOCAL CODES  
Install and use fireplace with care. Follow all  
local codes. In the absence of local codes, use  
the latest edition of The National Fuel Gas  
Code ANS Z223.1, also known as NFPA 54*.  
PRODUCT  
FEATURES  
2
SAFETY PILOT  
This fireplace has a pilot with an Oxygen  
Depletion Sensing (ODS) safety shutoff sys-  
tem. The ODS/pilot is a required feature for  
vent-freeroomfireplaces.TheODS/pilotshuts  
offthefireplaceifthereisnotenoughfreshair.  
*Available from:  
1
American National Standards Institute, Inc.  
1430 Broadway  
New York, NY 10018  
Hood  
PIEZO IGNITION SYSTEM  
National Fire Protection Association, Inc.  
Batterymarch Park  
This fireplace has a piezo ignitor. This sys-  
tem requires no matches, batteries, or other  
sources to light fireplace.  
Quincy, MA 02269  
Figure 2 - Removing Fireplace Hood  
THERMOSTATIC HEAT  
CONTROL  
This fireplace has a thermostat sensing bulb  
and a control valve. The thermostat will  
automatically modulate the heat output to  
maintain a consistent room temperature.  
This results in greater fireplace comfort.  
This can also result in lower gas bills.  
107031  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
VMH10TNB  
VENT-FREE NATURAL GAS COMPACT FIREPLACE  
ASSEMBLY  
Shoulder  
Screw  
Log  
WARNING: Always have  
branch support and screen in  
place before operating fireplace.  
Thispreventsexcessivetempera-  
tures on fireplace surfaces.  
WARNING: Failure to position  
thepartsinaccordancewiththese  
diagrams or failure to use only  
parts specifically approved with  
this fireplace may result in prop-  
erty damage or personal injury.  
Burner  
Support  
With Log  
Locator  
Tabs  
ASSEMBLING FIREPLACE  
Tools Required:  
• Phillips screwdriver  
• 5/16" hex wrench  
• slotted screwdriver  
• scissors  
Branch  
Support  
Screen  
Installing Log  
Figure 3 - Assembling Fireplace  
1. Lift screen up and pull out to remove.  
2. Cut two plastic straps to remove the log  
from the firebox cavity.  
4. Gently rotate hood to upright position.  
Make sure hood tabs are behind lou-  
vers and hood is resting on firebox top  
(see Figure 4).  
Assembling Hood  
1. Locate four black phillips sheet metal  
screws from the hardware packet.  
3. An optional blower is available. See Ac-  
cessories, page 27. Install optional  
blower now. Follow installation instruc-  
tions provided with blower.  
2. Rotate hood as shown in Figure 4.  
Make sure hood tabs point toward  
fireplace.  
5. Align screw holes on hood with screw  
holes on firebox top.  
4. Remove log packaging material and  
discard packaging. Gently place log on  
burner support (see Figure 3). The log  
should fit flat against top of burner sup-  
port and log locator tabs fit into the slots  
under the log. Do not allow log to con-  
tact flame. If flame contacts log, soot  
will be created.  
6. Insert screws as shown in Figure 4.  
Tighten screws firmly.  
3. Insert hood tabs between baffle and  
louvers (see Figure 4).  
Louver  
5. Reattach screen by placing the notches  
in the screen frame over the shoulder  
screws and pushing down.  
Hood Tab  
Baffle  
Hood  
Hood Tabs  
Sheet Metal  
Screws  
Firebox Top  
Figure 4 - Assembling Hood  
107031  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
Confined and Unconfined Space  
PROVIDING ADEQUATE  
VENTILATION  
AIR FOR  
The National Fuel Gas Code, ANS Z223.1  
defines a confined space as a space whose  
COMBUSTION AND  
VENTILATION  
The following are excerpts from National  
Fuel Gas Code. NFPA 54/ANS Z223.1, Sec-  
tion5.3, AirforCombustionandVentilation.  
volume is less than 50 cubic feet per 1,000  
Btu per hour (4.8 m3 per kw) of the aggre-  
gate input rating of all appliances installed  
in that space and an unconfined space as a  
space whose volume is not less than 50  
cubic feet per 1,000 Btu per hour (4.8 m3 per  
kw) of the aggregate input rating of all  
appliances installed in that space. Rooms  
communicating directly with the space in  
whichtheappliancesareinstalled*,through  
openings not furnished with doors, are con-  
sidered a part of the unconfined space.  
WARNING: This heater shall  
notbeinstalledinaconfinedspace  
or unusually tight construction  
unless provisions are provided  
foradequatecombustionandven-  
tilation air. Read the following in-  
structions to insure proper fresh  
air for this and other fuel-burning  
appliances in your home.  
All spaces in homes fall into one of the three  
following ventilation classifications:  
1. Unusually Tight Construction  
2. Unconfined Space  
3. Confined Space  
The information on pages 5 through 7 will  
help you classify your space and provide  
adequate ventilation.  
Unusually Tight Construction  
This heater shall not be installed in a con-  
fined space or unusually tight construction  
unless provisions are provided for adequate  
combustion and ventilation air.  
Today’s homes are built more energy effi-  
cient than ever. New materials, increased  
insulation, and new construction methods  
helpreduceheatlossinhomes.Homeowners  
weather strip and caulk around windows and  
doorstokeepthecoldairoutandthewarmair  
in. During heating months, home owners  
want their homes as airtight as possible.  
The air that leaks around doors and win-  
dows may provide enough fresh air for  
combustion and ventilation. However, in  
buildings of unusually tight construction,  
you must provide additional fresh air.  
* Adjoining rooms are communicating only  
iftherearedoorlesspassagewaysorventila-  
tion grills between them.  
Unusually tight construction is de-  
fined as construction where:  
While it is good to make your home energy  
efficient, your home needs to breathe. Fresh  
air must enter your home. All fuel-burning  
appliances need fresh air for proper com-  
bustion and ventilation.  
a. walls and ceilings exposed to the  
outside atmosphere have a con-  
tinuous water vapor retarder with  
a rating of one perm (6 x 10-11 kg  
per pa-sec-m2) or less with open-  
ings gasketed or sealed and  
Exhaustfans, fireplaces, clothesdryers, and  
fuel burning appliances draw air from the  
house to operate. You must provide ad-  
equate fresh air for these appliances. This  
will insure proper venting of vented fuel-  
burning appliances.  
b. weather stripping has been  
added on openable windows and  
doors and  
c. caulking or sealants are applied  
to areas such as joints around  
window and door frames, be-  
tween sole plates and floors, be-  
tween wall-ceiling joints, be-  
tween wall panels, at penetra-  
tions for plumbing, electrical, and  
gas lines, and at other openings.  
If your home meets all of the three  
criteria above, you must provide ad-  
ditional fresh air. See Ventilation Air  
From Outdoors, page 7.  
If your home does not meet all of the  
threecriteriaabove,proceedtoDeter-  
mining Fresh-Air Flow For Fireplace  
Location, page 6.  
Continued  
107031  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
VMH10TNB  
VENT-FREE NATURAL GAS COMPACT FIREPLACE  
AIR FOR  
COMBUSTION AND  
VENTILATION  
Continued  
DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATION  
Determining if You Have a Confined or Unconfined Space  
Use this worksheet to determine if you have a confined or unconfined space.  
Space: Includes the room in which you will install fireplace plus any adjoining rooms with doorless passageways or ventilation grills  
between the rooms.  
1. Determine the volume of the space (length x width x height).  
Length x Width x Height = ____________________ cu. ft. (volume of space)  
Example: Space size 16 ft. (length) x 14 ft. (width) x 8 ft. (ceiling height) = 1792 cu. ft. (volume of space)  
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of  
the space.  
2. Multiply the space volume by 1000 Btu/Hr per 50 cubic feet to determine the maximum Btu/Hr the space can support.  
_____________________(volume of space) x 1000 Btu/Hr = (Maximum Btu/Hr the space can support) 50 Cubic Feet  
Example: 1792 Cubic Feet (volume of space) x 1000 Btu/Hr ÷ 50 Cubic Feet= 35,840 Btu/Hr. This is the maximum Btu/Hr the  
space can support.  
3. Add the Btu/Hr of all fuel burning appliances in the space.  
Vent-free fireplace  
Gas water heater*  
Gas furnace  
________________________ Btu/Hr  
________________________ Btu/Hr  
________________________ Btu/Hr  
________________________ Btu/Hr  
________________________ Btu/Hr  
Example:  
Gas water heater  
Vent-free fireplace + 10,000 Btu/Hr  
Total 40,000 Btu/Hr  
30,000 Btu/Hr  
Vented gas heater  
Gas fireplace logs  
=
Other gas appliances* + ________________________ Btu/Hr  
Total = ________________________ Btu/Hr  
* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.  
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.  
_________________ Btu/Hr (maximum the space can support)  
_________________ Btu/Hr (actual amount of Btu/Hr used)  
Example: 35,840 Btu/Hr (maximum the space can support)  
40,000 Btu/Hr (actual amount of Btu/Hr used)  
The space in the above example is a confinedspace because the actual Btu/Hr used is more than the maximum Btu/Hr the space cansupport.  
You must provide additional fresh air. Your options are as follows:  
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin-  
ing room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 7.  
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 7.  
C. Install a lower Btu/Hr fireplace, if lower Btu/Hr size makes room unconfined.  
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no  
additional fresh air ventilation.  
WARNING:If the area in which the heater may be operated is smaller than that defined as an unconfined space  
or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of  
the methods described in the National Fuel Gas Code, ANS Z223.1, Section 5.3 or applicable local codes.  
107031  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
AIR FOR  
COMBUSTION AND  
12"  
VENTILATION  
Continued  
VENTILATION AIR  
Ventilation Grills  
Into Adjoining Room,  
Option 2  
Ventilation  
Grills  
into Adjoining  
Room,  
Ventilation Air From Inside  
Building  
Or  
Remove  
Door into  
Adjoining  
Room,  
Option 1  
Thisfreshairwouldcomefromanadjoining  
unconfined space. When ventilating to an  
adjoining unconfined space, you must pro-  
vide two permanent openings: one within  
12" of the ceiling and one within 12" of the  
floor on the wall connecting the two spaces  
(see options 1 and 2, Figure 5). You can also  
remove door into adjoining room (see op-  
tion 3, Figure 5). Follow the National Fuel  
Gas Code, NFPA 54/ANS Z223.1, Section  
5.3, Air for Combustion and Ventilation for  
required size of ventilation grills or ducts.  
Option 3  
12"  
Figure 5 - Ventilation Air from Inside Building Shown with Optional Mantel  
WARNING: Rework work-  
sheet, adding the space of the  
adjoining unconfined space. The  
combined spaces must have  
enough fresh air to supply all  
appliances in both spaces.  
Ventilated  
Outlet  
Attic  
Air  
Outlet  
Air  
To Attic  
Ventilation Air From Outdoors  
Provide extra fresh air by using ventilation  
grills or ducts. You must provide two per-  
manent openings: one within 12" of the  
ceiling and one within 12" of the floor.  
Connect these items directly to the outdoors  
orspacesopentotheoutdoors.Thesespaces  
include attics and crawl spaces. Follow the  
National Fuel Gas Code, NFPA 54/ANS  
Z223.1,Section5.3,AirforCombustionand  
Ventilation for required size of ventilation  
grills or ducts.  
To  
Crawl  
Space  
Inlet  
Air  
Ventilated  
Inlet Air  
Crawl Space  
Figure 6 - Ventilation Air from Outdoors Shown with Optional Mantel  
IMPORTANT:Do not provide openings for  
inlet or outlet air into attic if attic has a  
thermostat-controlledpowervent.Heatedair  
enteringtheatticwillactivatethepowervent.  
107031  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
VMH10TNB  
VENT-FREE NATURAL GAS COMPACT FIREPLACE  
sign-certifiedequipmentshutoffvalvefrom  
your dealer. See Accessories, page 27.  
INSTALLATION  
CAUTION:Thisheatercreates  
warmaircurrents.Thesecurrents  
moveheattowallsurfacesnextto  
heater. Installing heater next to  
vinyl or cloth wall coverings or  
operatingheaterwhereimpurities  
(suchastobaccosmoke,aromatic  
candles, cleaning fluids, oil or  
kerosene lamps, etc.) in the air  
exist, may discolor walls.  
NOTICE: This heater is intended  
for use as supplemental heat. Use  
this heater along with your pri-  
mary heating system. Do not in-  
stall this heater as your primary  
heat source. If you have a central  
heating system, you may run  
system’scirculationblowerwhile  
using heater. This will help circu-  
late the heat throughout the  
house. In the event of a power  
outage, you can use this heater as  
your primary heat source.  
Note:Ifdesired,purchaseafour-sidedbrass  
trim kit for built-in installations. See Acces-  
sories, page 27.  
LOCATING FIREPLACE  
WARNING: Maintain the mini-  
mum clearances shown in Figure  
7 and Figure 8, page 9. If you can,  
provide greater clearances from  
floor, ceiling, and joining wall.  
CAUTION: If you install the  
fireplace in a home garage  
• fireplacepilotandburnermust  
be at least 18 inches above  
floor.  
NOTICE: If you install the fire-  
place in a bedroom, some build-  
ing codes require that the fire-  
place/mantel system be secured  
to (or within) a wall. You can po-  
sitionfireplaceinanoptionalcabi-  
net or corner mantel. You can  
alsorecessfireplaceintothewall.  
WARNING: A qualified ser-  
vicepersonmustinstallfireplace.  
Follow all local codes.  
• locate fireplace where moving  
vehicle will not hit it.  
For convenience and efficiency, install  
fireplace  
Note: Your Vanguard fireplace is designed  
to be used in zero clearance installations.  
Wall or framing material can be placed  
directly against any exterior surface on the  
rear, sides, or top of your fireplace, except  
where standoff spacers are integrally at-  
tached. If standoff spacers are attached to  
your fireplace, these spacers can be placed  
directly against wall or framing materials.  
• where there is easy access for operation,  
inspection, and service  
If your fireplace is to be used with an optional  
mantel, the installation instructions included  
with your mantel shows an CSA/AGA ap-  
provedmethodofattachingthefireplace/man-  
tel system to a wall. IMPORTANT: Only use  
optionalcabinetorcornermantelsspecifiedin  
this manual. Purchase the optional mantel  
from your dealer (see Accessories, page 27).  
• in coldest part of room  
An optional blower kit is available from  
your dealer. See Accessories, page 27. If  
planning to use blower, follow instructions  
provided with the blower for power source.  
Use the dimensions shown for rough open-  
ings to create the easiest installations (see  
Built-In Fireplace Installation, page 9).  
IMPORTANT:Vent-freefireplacesaddmois-  
ture to the air. Although this is beneficial,  
installing fireplace in rooms without enough  
ventilationairmaycausemildewtoformfrom  
too much moisture. See Air for Combustion  
and Ventilation, pages 5 through 7.  
Ifyourfireplaceistoberecessedintothewall,  
see Built-In Fireplace Installation, page 9, to  
secure your fireplace into the wall.  
CHECK GAS TYPE  
Use only natural gas. If your gas supply is  
not natural gas, do not install fireplace. Call  
the dealer where you bought your fireplace  
for the proper type fireplace.  
WARNING: Never install the  
fireplace  
• in a bathroom  
CEILING  
• in a recreational vehicle  
• where curtains, furniture,  
clothing, or other flammable  
objectsarelessthan36inches  
from the front, top, or sides of  
the fireplace  
• as a fireplace insert  
• in high traffic areas  
• in windy or drafty areas  
INSTALLATION ITEMS  
36"  
Minimum  
Before installing fireplace, make sure you  
have the items listed below.  
6"  
Minimum  
From  
• piping (check local codes)  
• sealant (resistant to propane/LP gas)  
• equipment shutoff valve*  
• test gauge connection*  
• ground joint union  
• sediment trap  
Sides Of  
Fireplace  
Left  
Side  
Right  
Side  
• tee joint  
• pipe wrench  
FLOOR  
*AnCSA/AGAdesign-certifiedequipment  
shutoff valve with 1/8" NPT tap is an ac-  
ceptable alternative to test gauge connec-  
tion. Purchase the optional CSA/AGA de-  
Figure7-MountingClearancesAsViewed  
From Front of Fireplace Shown Built In  
The Wall  
107031  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
5. Carefully set fireplace in front of rough  
opening with back of fireplace inside  
wall opening.  
INSTALLATION  
Continued  
CEILING  
6. Attach flexible gas line to fireplace gas  
regulator. See Connecting Fireplace to  
Gas Supply, page 15.  
10 1/2"  
26 7/8"  
36"  
Minimum  
7. If the optional blower has been installed  
Top Of  
3/4" Off  
The Floor  
Minimum  
connect blower to electrical source.  
Mantel Can  
Be Flush  
With Wall  
Options one and two: Route blower  
electrical cord through side or rear ac-  
cess door of fireplace. Plug electrical  
cord into electrical outlet.  
26 7/8"  
Figure9-RoughOpeningforInstallingin  
Wall  
Right  
Side  
Option three: Have a licensed electri-  
cian connect blower to electrical source  
at junction box inside fireplace.  
Left  
Side  
36 5/8"  
25 7/8"  
8. Bend four nailing flanges on outer cas-  
ing with pliers (see Figure 11).  
26 7/8"  
51 3/4"  
9. Attach fireplace to wall studs using  
nails or wood screws through holes in  
nailing flange.  
Figure8-MountingClearancesAsViewed  
From Front of Fireplace Shown with Op-  
tional Mantel  
Figure 10 - Rough Opening for Installing  
in Corner  
10. Check all gas connections for leaks. See  
Checking Gas Connections, page 16.  
BUILT-IN FIREPLACE  
INSTALLATION  
2. An optional blower accessory is avail-  
able (see Accessories, page 27). There  
are three options for connecting blower  
to electrical source.  
11. If using optional brass trim kit, install  
the trim after final finishing and/or  
painting of wall. See instructions in-  
cluded with brass trim accessory for at-  
taching brass trim.  
Built-ininstallationofthisfireplaceinvolves  
installing fireplace into a framed-in enclo-  
sure. This makes the front of fireplace flush  
with wall. An optional brass trim kit acces-  
sory is available (see Accessories, page 27).  
Brasstrimwillextendpastsidesoffireplace  
approximately 1/2 inch. This will cover the  
rough edges of the wall opening. If install-  
ingabuilt-inmantelabovethefireplace, but  
you must follow the clearances shown in  
Figure 12, page 10. Follow the instructions  
below to install the fireplace in this manner.  
Note: Your Vanguard fireplace is designed  
to be used in zero clearance installations.  
Wall or framing material can be placed  
directly against any exterior surface on the  
rear, sides, or top of your fireplace.  
Option one: Install fireplace near an  
electrical outlet. See Blower Instruc-  
tions for power cord length.  
Option two: Have a licensed electrician  
install a properly grounded, three-prong  
120-volt electrical outlet at fireplace  
location. Locate outlet inside the  
framed enclosure. Blower power cord  
will plug into this outlet.  
Nails or  
Wood  
Screws  
Option three: Have a licensed electri-  
cian connect blower to electrical source  
at junction box inside fireplace.  
If using option one, have electrical out-  
let installed at this time. If using option  
two, do not connect blower to electrical  
source at junction box until step 7.  
Actual  
26"  
Framing  
26 7/8"  
26 7/8"  
10 1/2"  
3/4"  
Nailing  
Flanges  
3. Install gas piping to fireplace location.  
This installation includes an approved  
flexible gas line (if allowed by local  
codes) after the equipment shutoff  
valve. The flexible gas line must be the  
last item installed on the gas piping.  
Height  
Front Width  
Depth  
26 3/4"  
9 1/2"  
3/4"  
Bottom  
Figure 11 - Attaching Fireplace to Wall  
Studs  
1. Frame in rough opening. Use dimensions  
shown in Figure 9 for the rough opening.  
4. If you have not assembled firebox, fol-  
low instructions on page 4.  
If installing in a corner, use dimensions  
shown in Figure 10 for the rough open-  
ing. The height is 26 7/8" which is the  
same as the wall opening above.  
Continued  
107031  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
VMH10TNB  
VENT-FREE NATURAL GAS COMPACT FIREPLACE  
8. Place assembly next to wall at installa-  
OPTIONAL MANTEL  
INSTALLATION  
INSTALLATION  
tion location.  
Continued  
9. Remove brass trim kit and mantel. Be  
Note: Refer to instructions provided with  
Mantel Clearances for Built-In  
Installation  
careful not to damage wall or mantel.  
the mantel for assembly instructions. Refer  
to instructions below for system installa-  
tion. Refer to instructions on page 4 for  
firebox assembly. Blower accessory should  
be installed if it is being used (see Installing  
Blower Accessory GA3400T, pages 11  
through 13).  
10. Attach wood base to floor with two 1 3/4"  
black screws provided (see Figure 14). If  
the floor is concrete use anchor method  
(see AttachingWood Base to Solid Floor,  
page 14).  
If placing mantel above built-in fireplace,  
youmustmeetminimumclearancebetween  
mantel shelf and top of fireplace opening.  
NOTICE:Surfacetemperaturesof  
adjacent walls and mantels be-  
comehotduringoperation.Walls  
and mantels above the firebox  
may become hot to the touch. If  
installedproperly,thesetempera-  
turesmeettherequirementofthe  
national product standard. Fol-  
low all minimum clearances  
shown in this manual.  
11. Install gas line. See Connecting To Gas  
Supply, page 14.  
1. Unscrew four brass screws that attach  
top louver to fireplace. Remove louver  
from fireplace and set aside.  
12. Check for leaks. See Checking Gas  
Connections, page 16.  
13. Place mantel around fireplace. Be care-  
ful not to damage wall or mantel.  
2. Place fireplace on wood base.  
3. Place mantel around fireplace/base as-  
sembly.  
14. Place brass trim kit on the shoulder  
screws located on the side and top of  
the fireplace. Firmly snap the brass trim  
over the shoulder screws on fireplace  
(see Figure 13).  
4. Assemble brass trim kit. See Assem-  
bling Brass Trim, page 11.  
5. Firmly snap brass trim kit on shoulder  
screws. Shoulder screws are located on  
fireplace cabinet (see Figure 13).  
NOTICE: If your installation does  
notmeettheminimumclearances  
shown, you must do one of the  
following:  
• raise the mantel to an accept-  
able height  
15. Adjust assembly to remove any gaps.  
Attach remaining two 3" wood screws  
from hardware pack through openings  
inside of fireplace sides into the man-  
tel. The openings are located at top be-  
hind the area for the brass louvers (see  
Figure 13).  
6. Align brass trim kit for flush fit around  
opening.  
7. Use two 3" wood screws provided and  
attach fireplace base to wooden base  
(see Figure 13).  
• remove the mantel  
16. Reinstall top brass louvers.  
Mantel Shelf  
Shoulder  
Screws  
10"  
Note:  
8"  
6"  
All vertical  
measurements  
are from top of  
fireplace  
opening to  
bottom of  
Hole for 3"  
Wood Screw  
for Attaching  
Fireplace to  
Mantel  
1
2 /2"  
mantel shelf. All  
measurements  
are in inches.  
Hole for 3"  
Wood Screw  
for Attaching  
Fireplace to  
Wooden Base  
Assembled  
Brass Trim  
Figure 13 - Attaching Brass Trim to Fireplace  
Side of  
Firebox  
1 3/4" Screw  
Wood Base  
Figure 12 - Minimum Mantel Clearances  
for Built-In Installation  
Figure 14 - Attaching Wood Base to Floor  
107031  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
Branch  
Support  
INSTALLING BLOWER  
ACCESSORY GA3400T  
INSTALLATION  
Shoulder  
Screw  
Continued  
Removing Upper Louver  
Assembly  
Assembling Brass Trim (Brass  
trim shipped with mantel)  
1. Remove packaging from three remain-  
ing pieces of brass trim.  
Remove  
Screw  
To install the blower accessory, you must  
first remove the upper louver assembly.  
Valve  
Cover  
Shield  
2. Locate two adjusting plates with set  
screws, and two shims in the hardware  
packet.  
1. Lift screen off heater.  
2. Remove 4 screws from louver assem-  
bly (see Figure 16). Save these screws.  
2
3. Align shim under adjusting plate as  
shown in Figure 15.  
3. Pull louver assembly straight out from  
the cabinet. Be careful not to scratch  
the paint. Set louver assembly and  
screws aside.  
4. Slide one end of adjusting plate/shim  
in slot on mitered edge of top brass trim  
(see Figure 15).  
1
Blower Bracket  
Mounting Holes  
5. Slide other end of adjusting plate/shim  
in slot on mitered edge of side brass  
trim (see Figure 15).  
Bottom Louver  
Assembly  
Snap  
Bushings  
6. While firmly holding edges of brass  
trim together, tighten both set screws  
on the adjusting plate with slotted  
screwdriver.  
Figure 17 - Removing Valve Cover Shield  
Installing Blower Assembly  
7. Repeat steps 1 through 6 for other corner.  
8. Set brass assembly aside for later in-  
stallation.  
Upper Louver  
Assembly  
CAUTION: Label all wires  
priortodisconnectionwhenser-  
vicing controls. Wiring errors  
can cause improper and danger-  
ous operation.  
Brass Screws  
Top Brass Trim  
Figure 16 - Removing Upper Louver As-  
sembly  
Set  
Screws  
Slot  
Removing Valve Cover Shield  
CAUTION: Verify proper op-  
eration after servicing.  
Mitered  
Edge  
1. Open bottom louver assembly by  
swinging the assembly down (see Fig-  
ure 17).  
Shim  
Side Brass  
Trim  
Note: If you are using a mantel with your  
heater, use the following instructions. If  
your heater is built-in, see For Built-In In-  
stallation on page 13.  
Adjusting  
Plate  
2. Using short Phillips screwdriver, re-  
move the screw under the center of the  
branch support. Rotate valve cover  
shield clockwise and slide out.  
IMPORTANT: Do not remove shoul-  
der screw on the left side of valve cover  
shield. Slide the valve cover shield off  
of the shoulder screw (see Figure 17).  
Slot  
1. Install snap bushings found in hardware  
kit into both holes in rear of valve cover  
shield.  
Figure 15 - Assembling Brass Trim  
2. Make sure the wire harness is firmly  
connected to the terminals on the blower  
bracket assembly.  
Note: If you do not have a short Phillips  
screwdriver, the screen, logset, and  
branch support must be removed so a  
longer screwdriver may be used. See  
Connecting Fireplace To Gas Supply,  
page 15 and follow step 2.  
3. Note the wire locations on back of  
AUTO/OFF/ON switch. The terminals  
on back of switch are numbered 1, 2,  
and 3. Carefully remove red wire from  
terminal 1 and blue wire from terminal  
3. Black wire can remain on middle  
terminal 2 (see Figure 18, page 12).  
Continued  
107031  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
VMH10TNB  
VENT-FREE NATURAL GAS COMPACT FIREPLACE  
6. Route the wire harness through the 9. Install the switch plate on the valve  
INSTALLATION  
hole in left side of baffle. Pull wire  
harness through lower opening above  
where the valve shield was removed.  
(see Figure 18).  
cover shield with 2 #10 screws provided  
(see Figure 19). Reinstall the valve  
cover shield. Route power cord out of  
the cabinet by inserting it through the  
bushing on the outer casing (see Fig-  
ure 18). Plug fan kit into 120-Volt  
grounded power supply and test opera-  
tion. Note: When switch is in the  
AUTO position, the fan will start after  
the heater has run for a few moments.  
The fan will continue to run for several  
moments after the heater has been  
turned off. When switch is in the ON  
position, the fan will run until turned  
to OFF. Reinstall upper louver assem-  
bly and hood if previously removed,  
(see Figure 16, page 11). Close lower  
louver door.  
Continued  
4. Carefully disconnect green and white  
wires at their insulated connectors.  
7. Insert the 4 wire harness into one of the  
round holes in the rear of the valve cover  
shield and through the rectangular hole  
in the front of shield (see Figure 18).  
5. In top of the heater cabinet, locate the  
four mounting holes on the outer cas-  
ing. Align these four holes with those  
on the blower bracket assembly. Attach  
blower bracket assembly to the outer  
casing with 4 #10 screws provided (see  
Figure 18).  
8. Reconnect red wire to switch position  
3. Reconnect blue wire to switch posi-  
tion 1. Reconnect green and white wires.  
Wiring Routing  
Hole in Baffle  
Blower Bracket  
Assembly  
Screw  
Baffle  
Valve Cover  
Shield  
Wire  
Harness  
Switch  
Plate  
Switch  
Screw  
Power  
Cord  
Figure19-InstallingSwitchPlatetoValve  
Cover Shield  
3
2
1
Red  
Blue  
Switch  
Plate  
Wire  
Harness  
Valve Cover  
Shield  
Box Cover  
Figure 18 - Installing Blower Bracket Assembly  
107031  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
Fan Switch  
Extension Cord  
(Auto/Off/On)  
INSTALLATION  
Auto  
1
2
Off  
3
Thermostat  
Switch  
(N.O.)  
Blue  
Use extension cord if needed. The cord must  
have a three-prong, grounding plug and a  
three-hole receptacle. Make sure cord is in  
good shape. It must be heavy enoughto carry  
the current needed. An undersized cord will  
cause a drop in line voltage. This will result  
in loss of power and overheating. Use a No.  
16 AWG cord for lengths less than 50 feet.  
Continued  
On  
Blue  
For Built-In Installation  
110/115  
V.A.C.  
Red  
Blower  
Motor  
Black  
Red  
White  
Green  
White  
Green  
WARNING: A licensed elec-  
trician must connect the wiring  
harness to electrical supply fol-  
lowing all local codes. Electri-  
cian must provide a clamp on  
the box cover to secure the wir-  
ing. Wiring should be routed  
through the bushing in the hole  
on the outer casing of heater.  
Figure 20 - Wiring Diagram For Blower  
Accessory Built-In Installation  
Blower Bracket  
Assembly  
Screw  
Follow instructions Removing Valve Cover  
Shield (page 11), then  
1. Install a snap bushing found in hard-  
ware kit into one of the holes found on  
rear of valve cover shield. The other  
hole is for a strain relief clamp (not  
supplied) to secure incoming electrical  
supply.  
2. Follow steps 2 through 6 in Installing  
Blower Assembly, pages 11 and 12.  
Also remove black wire from middle  
switch terminal 2.  
Switch  
Wire  
Harness  
Power  
Cord  
3. Remove black plastic strain relief and  
power cord from switch plate. The  
power cord supplied will not be used in  
built-in installations. Pop in the plastic  
snap bushing found in hardware kit into  
the hole left by supply cord/strain relief.  
Outlet  
Receptacle  
3
2
1
Red  
Blue  
4. A licensed electrician must follow the  
wiring diagram to connect incoming  
electrical supply to fan kit wiring har-  
ness (see Figure 20).  
Switch Plate  
Plastic Wire  
Strap  
5. Plug power cord to the outlet receptacle  
(not provided) as shown in figure 21.  
Wind the extra cable in power cord and  
tie it up with the plastic wire strap (see  
Figure 21). Set the cable bundle be-  
tween the burner bracket and outer cas-  
ing, away from the burner.  
Valve  
Cover  
Shield  
Box Cover  
Wire  
Harness  
Clamp Connector  
(not included)  
6. Reinstall valve cover shield.  
Figure 21 - Installing Blower Bracket Assembly  
7. Test to make sure the blower is work-  
ing properly.  
8. Reinstall upper louver assembly and  
hood if previously removed, (see Figure  
16, page 11). Close lower louver door.  
Continued  
107031  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
VMH10TNB  
VENT-FREE NATURAL GAS COMPACT FIREPLACE  
Apply pipe joint sealant lightly to male  
INSTALLATION  
CAUTION: Use only new,  
black iron or steel pipe. Inter-  
nally-tinned copper tubing may  
be used in certain areas. Check  
your local codes. Use pipe of  
1/2" or greater diameter to al-  
low proper gas volume to fire-  
place. If pipe is too small, un-  
due loss of pressure will occur.  
threads. This will prevent excess sealant  
from going into pipe. Excess sealant in pipe  
could result in clogged fireplace valves.  
Continued  
Attaching Wood Base to Solid  
Floor  
CAUTION:Usepipejointseal-  
ant that is resistant to liquid pe-  
troleum (LP) gas.  
For attaching base to solid floors (concrete  
or masonry)  
Note: Floor anchors and mounting screws  
are in hardware package. The hardware  
package is provided with fireplace.  
We recommend that you install a sediment  
trap in supply line as shown in Figure 23.  
Locate sediment trap where it is within  
reach for cleaning. Install in piping system  
betweenfuelsupplyandheater.Locatesedi-  
ment trap where trapped matter is not likely  
to freeze. A sediment trap traps moisture  
and contaminants. This keeps them from  
going into fireplace controls. If sediment  
trap is not installed or is installed wrong,  
fireplace may not run properly.  
Installation must include an equipment  
shutoff valve, union, and plugged 1/8" NPT  
tap. Locate NPT tap within reach for test  
gauge hook up. NPT tap must be upstream  
from heater (see Figure 23).  
1. Drill holes at marked locations using  
5/16" drill bit. For solid floors (concrete  
or masonry), drill at least 1" deep.  
2. Fold floor anchor as shown in Figure 22.  
3. Insert floor anchor (wings first) into  
hole. Tap anchor flush to floor.  
IMPORTANT:Installanequipmentshutoff  
valve in an accessible location. The equip-  
ment shutoff valve is for turning on or shut-  
ting off the gas to the appliance.  
4. Insert mounting screws through base  
and into floor anchors.  
5. Tighten screws until base is firmly fas-  
tened to floor.  
Approved Flexible  
Gas Line  
CSA/AGA Design-Certified Equipment  
Shutoff Valve With 1/8" NPT Tap*  
Figure 22 - Folding Anchor  
CONNECTING TO GAS  
SUPPLY  
From Gas  
Meter (5"  
W.C. to  
WARNING: This appliance re-  
quires a 45° male flare fitting 5/8"-  
18 UNF (Unified National Fine  
Thread) inlet connection and the  
flexible gas line provided.  
10.5" W.C.  
Pressure)  
3" Minimum  
WARNING: A qualified ser-  
vice person must connect fire-  
place to gas supply. Follow all  
local codes.  
Pipe Nipple Cap Tee Joint  
Sediment Trap  
Figure 23 - Gas Connection  
WARNING: Never connect  
fireplace to private (non-utility)  
gas wells. This gas is commonly  
known as wellhead gas.  
* Purchase the optional CSA/AGA design-certified equipment shutoff valve from your  
dealer. See Accessories, page 27.  
IMPORTANT:Check gas line pressure be-  
fore connecting fireplace to gas line. Gas  
line pressure must be no greater than 14  
inchesofwater.Ifgaslinepressureishigher,  
fireplace regulator damage could occur.  
107031  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
INSTALLATION  
Continued  
Branch  
Support  
CONNECTING FIREPLACE  
TO GAS SUPPLY  
Installation Items Needed  
• Phillips screwdriver  
Shoulder  
Screw  
• sealant (resistant to propane/LPgas, not  
provided)  
Flexible Gas  
Line  
1. Remove fireplace screen. Remove two  
screws that hold fireplace screen in  
place for shipping. These screws are  
located near top of screen. Discard  
screws. Lift fireplace screen up and pull  
out to remove.  
2. Remove screws that attach branch sup-  
port to fireplace (see Figure 24). Care-  
fully lift up branch support and remove  
from fireplace (see Figure 24).  
Screen  
Figure 24 - Removing Log Base Assembly From Fireplace  
3. Route flexible gas line (provided by  
installer) from equipment shutoff valve  
into fireplace through side or rear ac-  
cess holes in outer casing. Route flex-  
ible gas supply line through fireplace  
access holes in outer casing.  
Gas Connector  
To Fireplace  
Gas Regulator  
Equipment Shutoff Valve  
NOTICE:Mostbuildingcodesdo  
not permit concealed gas con-  
nections. A flexible gas line is  
provided to allow accessibility  
fromthefireplace(seeFigure25).  
The flexible gas supply line con-  
nection to the equipment shutoff  
valve should be accessible.  
To Gas  
Supply  
Flexible Gas Line from  
Fireplace Gas Regulator  
Provided With Fireplace  
Equipment Shutoff Valve  
Flexible Gas Line from  
Provided By Installer  
Figure 25 - Attaching Flexible Gas Lines Together  
4. Apply pipe joint sealant lightly to male  
threads of gas connector attached to  
flexible gas line (see Figure 25). Con-  
nect flexible gas line to flexible gas line  
attached to gas regulator of fireplace  
(see Figure 25).  
5. Check all gas connections for leaks. See  
Checking Gas Connections, page 16.  
6. Replace branch support back into fire-  
place. Feed flexible gas line into fire-  
place base area while replacing branch  
support. Make sure the entire flexible  
gas line is in fireplace base area. Reat-  
tach branch support to fireplace with  
screws removed in step 2.  
Continued  
107031  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
VMH10TNB  
VENT-FREE NATURAL GAS COMPACT FIREPLACE  
Test Pressures Equal To or Less Than  
1/2 PSIG (3.5 kPa)  
Pressure Testing Fireplace Gas  
Connections  
1. Open equipment shutoff valve (see Fig-  
INSTALLATION  
Continued  
1. Close equipment shutoff valve (see Fig-  
ure 26).  
ure 26).  
CHECKING GAS  
CONNECTIONS  
2. Pressurize supply piping system by ei-  
ther using compressed air or opening  
main gas valve located on or near gas  
meter.  
2. Open main gas valve located on or near  
gas meter.  
WARNING: Test all gas pip-  
3. Make sure control knob of fireplace is  
in the OFF position.  
ing and connections for leaks  
after installing or servicing. Cor-  
rect all leaks at once.  
3. Check all joints from gas meter to  
equipment shutoff valve (see Figure  
27). Apply mixture of liquid soap and  
water to gas joints. Bubbles forming  
show a leak.  
4. Check all joints from equipment shutoff  
valve to thermostat gas valve (see Fig-  
ure 27). Apply mixture of liquid soap  
and water to gas joints. Bubbles form-  
ing show a leak.  
WARNING:Neveruseanopen  
flame to check for a leak. Apply a  
mixture of liquid soap and water  
to all joints. Bubbles forming  
show a leak. Correct all leaks at  
once.  
4. Correct all leaks at once.  
5. Correct all leaks at once.  
6. Light fireplace (see Operating Fire-  
place, pages 17 and 18). Check all other  
internal joints for leaks.  
Equipment  
Shutoff  
Valve  
Open  
7. Turn off fireplace (see To Turn Off Gas  
Pressure Testing Gas Supply  
Piping System  
to Appliance, page 18).  
8. Replace front panel.  
Test Pressures In Excess Of 1/2 PSIG  
(3.5 kPa)  
Closed
1. Disconnect appliance with its appliance  
main gas valve (control valve) and equip-  
ment shutoff valve from gas supply pip-  
ing system. Pressures in excess of 1/2  
psig will damage heater regulator.  
Figure 26 - Equipment Shutoff Valve  
2. Cap off open end of gas pipe where  
equipment shutoff valve was connected.  
3. Pressurize supply piping system by ei-  
ther using compressed air or opening  
main gas valve located on or near gas  
meter.  
Equipment  
Shutoff  
Valve  
Gas Meter  
4. Check all joints of gas supply piping  
system. Apply mixture of liquid soap  
and water to gas joints. Bubbles form-  
ing show a leak.  
5. Correct all leaks at once.  
6. Reconnect fireplace and equipment  
shutoff valve to gas supply. Check re-  
connected fittings for leaks.  
Figure 27 - Checking Gas Joints  
107031  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
Note: You may be running this fire-  
place for the first time after hooking  
up to gas supply. If so, the control  
knob may need to be pressed in for  
30 seconds. This will allow air to  
bleed from the gas system.  
• If control knob does not pop up  
when released, contact a qualified  
service person or gas supplier for  
repairs.  
LIGHTING  
INSTRUCTIONS  
OPERATING  
FIREPLACE  
WARNING: You must operate  
this fireplace with the fireplace  
screen in place. Make sure fire-  
place screen is installed before  
running fireplace.  
FOR YOUR SAFETY  
READ BEFORE  
LIGHTING  
WARNING: If you do not fol-  
low these instructions exactly, a  
fireorexplosionmayresultcaus-  
ing property damage, personal  
injury or loss of life.  
NOTICE: During initial operation  
of new fireplace, burning logs  
will give off a paper-burning  
smell.Openwindowtoventsmell.  
Operate fireplace on HI position  
to burn off odor. This will only  
last a few hours.  
6. With control knob pressed in, push  
down and release ignitor button. This  
will light pilot. The pilot is attached  
to the front of burner. If needed, keep  
pressing ignitor button until pilot  
lights.  
A. This appliance has a pilot which must  
be lighted by hand. When lighting the  
pilot, follow these instructions exactly.  
Note: If pilot does not stay lit, refer  
to Troubleshooting, pages 20 through  
22. Also contact a qualified service  
person or gas supplier for repairs.  
Until repairs are made, light pilot with  
match. To light pilot with match, see  
Manual Lighting Procedure, page 18.  
1. STOP! Read the safety information,  
column 1.  
B. BEFORE LIGHTING smell all  
around the appliance area for gas. Be  
sure to smell next to the floor because  
some gas is heavier than air and will  
settle on the floor.  
2. Make sure equipment shutoff valve  
is fully open.  
3. Turn control knob clockwise  
Clockwise  
WHAT TO DO IF YOU SMELL  
GAS  
to the OFF position.  
7. Keep control knob pressed in for 30  
seconds after lighting pilot. After 30  
seconds, release control knob.  
4. Wait five (5) minutes to clear out any  
gas. Then smell for gas, including  
near the floor. If you smell gas,  
STOP! Follow “B” in the safety in-  
formation, column 1. If you don’t  
smell gas, go to the next step.  
• Do not try to light any appliance.  
• Do not touch any electric switch; do  
not use any phone in your building.  
• Immediately call your gas supplier  
from a neighbor’s phone. Follow  
the gas supplier’s instructions.  
• If you cannot reach your gas sup-  
plier, call the fire department.  
Note: If pilot goes out, repeat steps  
3 through 7. This fireplace has a  
safety interlock system. Wait one (1)  
minute before lighting pilot again.  
5. Turn control knob counterclockwise  
8. Turn control knob counterclockwise  
to the PILOT position. Press  
in control knob for five (5) seconds  
(see Figure 28).  
C-clockwise  
to desired heating level. The  
C-clockwise  
C. Use only your hand to push in or turn  
the gas control knob. Never use tools.  
If the knob will not push in or turn  
by hand, don’t try to repair it, call a  
qualified service technician or gas  
supplier. Force or attempted repair  
may result in a fire or explosion.  
main burner should light. Set control  
knob to any heat level between HI  
and LO.  
Ignitor Button  
Control Knob  
CAUTION:Donottrytoadjust  
heatinglevelsbyusingtheequip-  
ment shutoff valve.  
D. Do not use this appliance if any part  
has been under water. Immediately  
call a qualified service technician to  
inspect the appliance and to replace  
any part of the control system and  
any gas control which has been un-  
der water.  
Ignitor Electrode  
Thermocouple  
Pilot Burner  
Figure 28 - Control Knob In The OFF  
Position  
Figure 29 - Pilot  
(Actual Pilot May Vary From Illustration)  
Continued  
107031  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
VMH10TNB  
VENT-FREE NATURAL GAS COMPACT FIREPLACE  
MANUAL LIGHTING  
PROCEDURE  
1. Follow steps 1 through 5 under Light-  
OPERATING  
FIREPLACE  
Continued  
ing Instructions, page 17.  
2. With control knob pressed in, strike  
TO TURN OFF GAS  
match. Hold match to pilot until pi-  
lot lights.  
TO APPLIANCE  
Shutting Off Fireplace  
1. Turn control knob clockwise  
to the OFF position.  
3. Keep control knob pressed in for 30  
seconds after lighting pilot. After 30  
seconds, release control knob. Now  
follow step 8, page 17.  
2. Turn off all electric power to the ap-  
pliance if service is to be performed.  
OPERATING BLOWER  
Shutting Off Burner Only (pilot  
stays lit)  
This blower has three settings: ON, OFF,  
andAUTO.IntheONposition,theblower  
will operate constantly. In the OFF posi-  
tion, the blower will not operate. In the  
AUTOposition,theblowerwillstartwhen  
thethermostatsensesasufficientincrease  
in firebox temperature.  
Turn control knob clockwise  
the PILOT position.  
to  
Thermostat Control Operation  
The thermostat used on this fireplace  
senses the room temperature. At times  
the room may exceed the set tempera- Note: Your fireplace and thermostat  
ture. If so, the burner will shut off. The blower will not turn on and off at the  
burner will cycle back on when room same time. The fireplace may run for  
temperature drops below the set tem- several minutes before the blower turns  
perature.  
on.Aftertheheatermodulatestothepilot  
position, the blower will continue to run.  
The blower will shut off after the firebox  
temperature decreases.  
The control knob can be set to any heat  
level between HI and LO.  
Note: The thermostat sensing bulb mea-  
sures the temperature of air near the  
fireplace cabinet. This may not always  
agree with room temperature (depend-  
ing on housing construction, installation  
location, room size, open air tempera-  
tures, etc.). Frequent use of your fire-  
place will let you determine your own  
comfort levels.  
Note: It is safe to operate fireplace with  
blower turned off. However, the blower  
helps distribute heated air from the  
fireplace.  
Auto/Off/On Switch  
ON  
OFF  
Figure 30 - Auto/Off/On Switch  
107031  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
BURNER FLAME PATTERN  
INSPECTING  
BURNER  
Figure 33 shows a correct burner flame  
pattern.Figure34showsanincorrectburner  
flame pattern. The incorrect burner flame  
pattern shows the flame consistently higher  
than one inch above the log.  
Check pilot flame pattern and burner flame  
pattern often.  
PILOT FLAME PATTERN  
Ifburnerflamepatternisincorrect,asshown  
in Figure 34  
Figure31showsacorrectpilotflamepattern.  
Figure 32 shows an incorrect pilot flame  
pattern.Theincorrectpilotflameisnotprop-  
erlyheatingthethermocouple.Thiswillcause  
the thermocouple to cool. When the thermo-  
couple cools, the fireplace will shut down.  
• turn fireplace off (see To Turn Off Gas to  
Appliance, page 18)  
• see Troubleshooting, pages 20 through 22  
Top of Flame About  
One Inch Below Logs  
If pilot flame pattern is incorrect, as shown  
in Figure 32  
• turn fireplace off (see To Turn Off Gas to  
Appliance, page 18)  
• see Troubleshooting, pages 20 through 22  
Thermocouple  
Pilot Burner  
Figure 33 - Correct Burner Flame Pattern  
Top of Flame Consistently About  
One Inch Higher Than Logs  
Figure 31 - Correct Pilot Flame Pattern  
(Actual Pilot May Vary From Illustration)  
Figure 34 - Incorrect Burner Flame Pattern  
Thermocouple  
Pilot Burner  
Figure 32 - Incorrect Pilot Flame Pattern  
(Actual Pilot May Vary From Illustration)  
107031  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
VMH10TNB  
VENT-FREE NATURAL GAS COMPACT FIREPLACE  
TROUBLESHOOTING  
Note: For additional help, visit DESA  
International’stechnicalservicewebsite  
WARNING: Turn off and un-  
plug fireplace and let cool before  
servicing. Only a qualified ser-  
vice person should service and  
repair fireplace.  
CAUTION: Never use a wire,  
needle, or similar object to clean  
ODS/pilot.ThiscandamageODS/  
pilot unit.  
Note:Alltroubleshootingitemsarelistedin  
order of operation.  
OBSERVED PROBLEM  
POSSIBLE CAUSE  
REMEDY  
When ignitor button is pressed, there is no 1. Ignitor cable pinched or wet  
spark at ODS/pilot  
1. Free ignitor cable if pinched by any  
metal or tubing. Keep ignitor cable dry  
2. Ignitor electrode not connected to ignitor 2. Reconnect ignitor cable  
cable  
3. Broken ignitor cable  
4. Bad piezo ignitor  
5. Ignitor electrode broken  
6. Ignitor electrode positioned wrong  
3. Replace ignitor cable  
4. Replace piezo ignitor  
5. Replace ignitor  
6. Replace ignitor  
When ignitor button is pressed, there is 1. Gas supply turned off or equipment 1. Turn on gas supply or open equipment  
spark at ODS/pilot but no ignition  
shutoff valve closed  
shutoff valve  
2. Control knob not in PILOT position  
2. Turn control knob to PILOT position  
3. Control knob not pressed in while in 3. Press in control knob while in PILOT  
PILOT position  
position  
4. Air in gas lines when installed  
4. Continue holding down control knob. Re-  
peat igniting operation until air is removed  
5. Clean ODS/pilot (see Cleaning and  
Maintenance, page 23) or replace ODS/  
pilot assembly  
5. ODS/pilot is clogged  
6. Gas regulator setting is not correct  
6. Replace gas regulator  
ODS/pilot lights but flame goes out when 1. Control knob not fully pressed in  
1. Press in control knob fully  
control knob is released  
2. Control knob not pressed in long enough 2. After ODS/pilot lights, keep control  
knob pressed in 30 seconds  
3. Safety interlock system has been triggered 3. Wait one minute for safety interlock sys-  
tem to reset. Repeat ignition operation  
4. Equipment shutoff valve not fully open 4. Fully open equipment shutoff valve  
5. Thermocouple connection loose at con- 5. Hand tighten until snug, then tighten 1/4  
trol valve  
turn more  
6. Pilot flame not touching thermocouple, 6. A) Contact local natural gas company  
which allows thermocouple to cool,  
causing pilot flame to go out. This prob-  
lem could be caused by one or both of  
the following:  
B) Clean ODS/pilot (see Cleaning and  
Maintenance, page 23) or replace ODS/  
pilot assembly  
A) Low gas pressure  
B) Dirty or partially clogged ODS/pilot  
7. Thermocouple damaged  
8. Control valve damaged  
7. Replace thermocouple  
8. Replace control valve  
107031  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
TROUBLESHOOTING  
Continued  
OBSERVED PROBLEM  
POSSIBLE CAUSE  
REMEDY  
Burner does not light after ODS/pilot is lit  
1. Burner orifice is clogged  
1. Clean burner (see Cleaning and Mainte-  
nance, page 23) or replace burner orifice  
2. Replace burner orifice  
2. Burner orifice diameter is too small  
3. Inlet gas pressure is too low  
3. Contact local natural gas company  
Delayed ignition of burner  
1. Manifold pressure is too low  
2. Burner orifice is clogged  
1. Contact local natural gas company  
2. Clean burner (see Cleaning and Mainte-  
nance, page 23) or replace burner orifice  
Burner backfiring during combustion  
1. Burner orifice is clogged or damaged  
1. Clean burner (see Cleaning and Mainte-  
nance, page 23) or replace burner orifice  
2. Replace burner pressure  
2. Burner damaged  
3. Low inlet gas pressure  
3. Contact local natural gas company  
4. Gas regulator defective  
4. Replace gas regulator  
Slight smoke or odor during initial operation 1. Residues from manufacturing processes 1. Problem will stop after a few hours of  
operation  
Fireplace produces a whistling noise when 1. Air in gas line  
burner is lit  
1. Operate burner until air is removed from  
line. Have gas line checked by local  
natural gas company  
2. Air passageways on fireplace blocked  
2. Observe minimum installation clearances  
(see pages 8 through 10)  
3. Dirty or partially clogged burner orifice 3. Clean burner (see Cleaning and Mainte-  
nance, page 23) or replace burner orifice  
Whitepowderresidueformingwithinburner 1. When heated, vapors from furniture pol- 1. Turn heater off when using furniture  
box or on adjacent walls or furniture  
ish, wax, carpet cleaners, etc. turn into  
polish, wax, carpet cleaners, or similar  
white powder residue  
products  
Continued  
107031  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
VMH10TNB  
VENT-FREE NATURAL GAS COMPACT FIREPLACE  
TROUBLESHOOTING  
Continued  
WARNING: If you smell gas  
• Shut off gas supply.  
• Do not try to light any appliance.  
• Do not touch any electrical switch; do not use any phone in your  
building.  
• Immediatelycallyourgassupplierfromaneighbor’sphone. Followthe  
gas supplier’s instructions.  
• If you cannot reach your gas supplier, call the fire department.  
IMPORTANT:Operatingfireplacewhereimpuritiesinairexistmaycreateodors.Cleaning  
supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles,  
etc., create fumes. These fumes may mix with combustion air and create odors.  
OBSERVED PROBLEM  
POSSIBLE CAUSE  
REMEDY  
Fireplace produces a clicking/ticking noise 1. Metal expanding while heating or con- 1. This is common with most fireplaces. If  
just after burner is lit or shut off  
tracting while cooling  
noise is excessive, contact qualified ser-  
vice person  
Fireplace produces unwanted odors  
1. Fireplace burning vapors from paint, hair 1. Ventilate room. Stop using odor caus-  
spray, glues, etc. (See IMPORTANT  
ing products while fireplace is running  
statement above)  
2. Gas leak. SeeWarning statement at 2. Locate and correct all leaks (see Check-  
top of page  
ing Gas Connections, page 16)  
Fireplace shuts off in use (ODS operates)  
1. Not enough fresh air is available  
2. Low line pressure  
3. ODS/pilot is partially clogged  
1. Open window and/or door for ventilation  
2. Contact local natural gas company  
3. Clean ODS/pilot (see Cleaning and  
Maintenance, page 23)  
Gas odor even when control knob is in OFF 1. Gas leak. SeeWarning statement at 1. Locate and correct all leaks (see Check-  
position  
top of page  
ing Gas Connections, page 16)  
2. Control valve defective  
2. Replace control valve  
Gas odor during combustion  
1. Foreign matter between control valve 1. Take apart gas tubing and remove foreign  
and burner matter  
2. Gas leak. SeeWarning statement at 2. Locate and correct all leaks (see Check-  
top of page  
ing Gas Connections, page 16)  
Moisture/condensationnoticedonwindows 1. Not enough combustion/ventilation air  
1. Refer to Air for Combustion and Venti-  
lation requirements (page 5)  
107031  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
4. Check the injector holder located at the  
CLEANING AND  
MAINTENANCE  
SERVICE HINTS  
When Gas Pressure Is Too Low  
• pilot will not stay lit  
end of the burner tube again. Remove  
any large particles of dust, dirt, lint, or  
pet hair with a soft cloth or vacuum  
cleaner nozzle.  
WARNING: Turn off fireplace  
and let cool before cleaning.  
• burner will have delayed ignition  
• fireplace will not produce specified heat  
5. Blow air into the primary air holes on  
the injector holder.  
6. In case any large clumps of dust have  
now been pushed into the burner repeat  
steps 3 and 4.  
When Gas Quality Is Bad  
• pilot will not stay lit  
CAUTION: You must keep  
control areas, burner, and circu-  
lating air passageways of fire-  
place clean. Inspect these areas  
offireplacebeforeeachuse.Have  
fireplace inspected yearly by a  
qualified service person. Fire-  
place may need more frequent  
cleaning due to excessive lint  
from carpeting, pet hair, bedding  
material, etc.  
• burner will produce flames and soot  
• fireplace will backfire when lit  
Clean the pilot assembly also. A yellow tip  
on the pilot flame indicates dust and dirt in  
the pilot assembly. There is a small pilot air  
inlet hole about two inches from where the  
pilot flame comes out of the pilot assembly  
(see Figure 36). With the unit off, lightly  
blow air through the air inlet hole. You may  
blowthroughadrinkingstrawifcompressed  
air is not available.  
Youmayfeelyourgaspressureistoolowor  
gas quality is bad. If so, contact your local  
natural gas supplier.  
TECHNICAL  
SERVICE  
You may have further questions about in-  
stallation, operation, or troubleshooting.  
Injector Holder  
CLEANING BURNER  
INJECTOR HOLDER AND  
PILOT AIR INLET HOLE  
If so, contact DESA International’s Techni-  
cal Service Department at 1-800-323-5190.  
Ports/Slots  
The primary air inlet holes allow the proper  
amount of air to mix with the gas. This  
provides a clean burning flame. Keep these  
holes clear of dust, dirt, lint, and pet hair.  
Clean these air inlet holes prior to each  
heating season. Blocked air holes will cre-  
ate soot. We recommend that you clean the  
unit every three months during operation  
and have heater inspected yearly by a quali-  
fied service person.  
You can also visit DESA International’s  
technical services web site at  
Burner  
Tube  
Primary Air Inlet  
Holes  
Figure 35 - Injector Holder On Outlet  
Burner Tube  
Wealsorecommendthatyoukeeptheburner  
tube and pilot assembly clean and free of  
dustanddirt.Tocleanthesepartswerecom-  
mend using compressed air no greater than  
30 PSI. Your local computer store, hard-  
ware store, or home center may carry com-  
pressed air in a can. You can use a vacuum  
cleaner in the blow position. If using com-  
pressed air in a can, please follow the direc-  
tions on the can. If you don't follow direc-  
tions on the can, you could damage the pilot  
assembly.  
Pilot Air Inlet Hole  
Pilot  
Assembly  
Figure 36 - Pilot Inlet Air Hole  
CABINET  
1. Shut off the unit, including the pilot.  
Allow the unit to cool for at least thirty  
minutes.  
Air Passageways  
• Use a vacuum cleaner or pressurized air  
to clean.  
2. Inspect burner, pilot, and primary air  
inlet holes on injector holder for dust  
and dirt (see Figure 35).  
Exterior  
• Use a soft cloth dampened with a mild  
soap and water mixture. Wipe the cabi-  
net to remove dust.  
3. Blow air through the ports/slots and  
holes in the burner.  
107031  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
VMH10TNB  
VENT-FREE NATURAL GAS COMPACT FIREPLACE  
ILLUSTRATED  
PARTS  
BREAKDOWN  
3
VMH10TNB  
1
17  
9
7
29  
4
8
10  
8
3
3
2
11  
4
32  
42  
4
14  
25  
24  
28  
20  
12-1  
23  
8
13  
36  
31  
19  
14  
34  
33  
38  
39  
37  
41  
25  
5
12  
6
24  
18  
38  
35  
12  
15  
27  
22  
40  
26  
21  
16  
30  
107031  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
PARTS LIST  
KEY  
NO.  
VMH10TNA  
PART NO.  
DESCRIPTION  
QTY.  
VMH10TNB  
1
2
3
4
5
6
7
8
102633-02CK  
102624-02  
099230-02  
098304-01  
103591-01  
103209-03  
102635-02CK  
M11084-26  
103209-01  
104281-01  
102638-01  
104285-01  
102460-01CJ  
099211-01  
103963-01  
103671-01  
100587-01  
098303-02  
104335-01CK  
102649-02CK  
099415-10  
102875-01  
101381-01  
099387-03  
098271-06  
M11084-38  
101004-12  
098522-14  
102639-01  
101628-01  
102869-01  
102731-01  
103295-01CJ  
107153-01  
104313-01  
104313-02  
M10908-2  
Outer Casing Top  
Outer Casing  
Shoulder Screw  
Screw, #10 x 3/8"  
Burner  
Louvered Door  
Left and Right Side Front  
Hex Head Screw, #10 x 3/8"  
Brass Top Louver  
Firebox Hood  
1
1
14  
16  
1
1
2
31  
1
1
1
1
1
2
1
1
4
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
2
1
1
2
1
This list contains replaceable parts used in  
your fireplace. When ordering parts, follow  
the instructions listed under Replacement  
Parts on page 26 of this manual.  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
Firebox Top  
ODS/Pilot Assembly  
Firebox Wrapper  
Control Bracket Screw  
Inlet Tube  
Outlet Tube  
Brass Screw, #6 x 3/8  
Regulator Screw  
Outer Shell Base  
Branch Support  
Gas Regulator  
Regulator Bracket  
Valve Cover and Piezo  
Pilot Tube  
Ignitor Cable  
Screw #8 x 3/8  
Injector  
Gas Valve  
Baffle  
Flexible Connector  
Control Bracket  
Control Shield  
Screen Assembly  
Log Set  
Hinge Pin (Right)  
Hinge Pin (Left)  
Hinge Screws  
Burner Support  
Pilot Bracket  
3/8" NPT x 3/8" Flare Brass Fitting  
Nut, M5  
103734-01  
101006-01  
097809-03  
098249-01  
101629-02  
Bushing  
PARTS AVAILABLE — NOT SHOWN  
101054-01  
100563-01  
103470-01  
104319-04  
Lighting Instructions Plate  
Warning Plate  
Hardware Package  
Video, Instruction  
1
1
1
1
107031  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
VMH10TNB  
VENT-FREE NATURAL GAS COMPACT FIREPLACE  
SPECIFICATIONS  
Input Rate  
10,000 Btu/Hr  
Natural Only  
Piezo  
Type Gas  
Ignition  
Pressure Regulator Setting  
Inlet Gas Pressure (in. of water)*  
Maximum  
3" W.C.  
10.5"  
5"  
Minimum  
Dimensions, Inches (H x W x D)  
Fireplace (including hood and screws)  
Carton  
25 7/8 x 26 13/16 x 9 3/8  
32 5/8 x 27 3/16 x 11 5/8  
Weight, pounds  
Fireplace  
Shipping  
44 1/2 lbs.  
48 lbs.  
* For purposes of input adjustment  
REPLACEMENT  
PARTS  
Note: Use only original replacement parts.  
Thiswillprotectyourwarrantycoveragefor  
parts replaced under warranty.  
PARTS UNDER WARRANTY  
Contact authorized dealers of this product.  
If they can’t supply original replacement  
part(s) call DESA International’s Technical  
Service Department at 1-800-323-5190 for  
referral information.  
WhencallingDESAInternational,haveready  
• your name  
• your address  
• model and serial numbers of your fireplace  
• how fireplace was malfunctioning  
• type of gas used (propane/LPor natural gas)  
• purchase date  
Usually, we will ask you to return the defec-  
tive part to the factory.  
PARTS NOT UNDER  
WARRANTY  
Contact authorized dealers of this product.  
If they can’t supply original replacement  
part(s) call DESA International’s Parts De-  
partment at 1-800-972-7879 for referral in-  
formation.  
WhencallingDESAInternational,haveready  
• model number of your fireplace  
• the replacement part number  
107031  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
CLEANING KIT - GCK  
(Not Shown)  
ACCESSORIES  
Purchase these fireplace accessories from  
your local dealer. If they cannot supply these  
accessories call DESA International’s Sales  
Department at 1-800-458-2472 for referral  
information. You can also write to the ad-  
dress listed on the back page of this manual.  
Your vent-free gas appliance requires regu-  
lar cleaning and maintenance to prevent  
performance problems. This kit gives you  
the tools and instructions to make it easy to  
clean all critical areas of your appliance.  
CABINET MANTEL WITH  
BUILT-IN HEARTH BASE  
AND TRADITIONAL SQUARE  
LEG STYLING  
EQUIPMENT SHUTOFF  
VALVE - GA5010  
Equipmentshutoffvalvewith1/8"NPTtap.  
Unfinished - GM923U  
Finished - GM922F  
For use with fireplace. A hardwood mantel  
and hearth base offers compact styling and  
completes the fireplace look. Available in a  
stained or an unfinished (ready to stain or  
paint) Oak Veneer over hardwood. Com-  
pleteassemblyinstructionsincluded.Three-  
sided brass trim kit included.  
CABINET MANTEL WITH  
BUILT-IN HEARTH BASE AND  
ROUNDED LEG STYLING  
Unfinished - GM921U  
BRASS TRIM KIT - GA6095  
Optional four-sided brasstrim kit forrecessed  
built-ininstallations(whenunitisraisedoffof  
the floor. Provides a finished appearance by  
covering rough edges of wall opening.  
Walnut Finished - GM920F  
Cherry Finished - GM924F  
(Appearance May Differ by Model)  
For use with fireplace. A hardwood mantel  
and hearth base offers compact styling and  
completes the fireplace look. Available in a  
walnut finished, cherry fininshed, or an un-  
finished hardwood, ready to stain or paint.  
Complete assembly instructions included.  
Three-sided brass trim kit included.  
BRASS TRIM KIT - GA6094  
Optional three-sided brass trim kit for cus-  
tom and recessed installations (when unit is  
on the floor). Provides a finished appear-  
ance by covering rough edges of wall open-  
ing. Included with all mantels.  
CORNER MANTEL WITH  
BUILT-IN HEARTH BASE  
Unfinished - GM721U  
Finished - GM720F  
THERMOSTATICALLY -  
CONTROLLED BLOWER KIT  
GA3400T  
Forusewithfireplace. Space-savingmantel  
andhearthbasecornerdesignfeaturesclean,  
classic lines. Available in a walnut finish or  
an unfinished hardwood, ready to stain or  
paint. Complete assembly instructions in-  
cluded. Three-sided brass trim kit included.  
Providesbetterheatdistribution.Makesfire-  
place more efficient. Automatically turns  
off and on as needed.  
107031  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY INFORMATION  
KEEP THIS WARRANTY  
Model  
Serial No.  
Date Purchased  
Always specify model and serial numbers when communicating with the factory.  
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written  
warranty. We make no other warranty, expressed or implied.  
LIMITED WARRANTY  
VENT-FREE NATURAL GAS COMPACT CLASSIC HEARTH® FIREPLACE  
DESA International warrants this product to be free from defects in materials and components for four (4) years and five (5) years  
on stainless steel burners from the date of first purchase, provided that the product has been properly installed, operated and  
maintained in accordance with all applicable instructions. To make a claim under this warranty the Bill of Sale or cancelled check  
must be presented.  
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this  
fireplacetoproperoperatingconditionandanallowanceforlaborwhenprovidedbyaDESAAuthorizedServiceCenter.Warranty  
part(s) MUST be obtained through authorized dealers of this product and/or DESA International who will provide original factory  
replacement parts. Failure to use original factory replacement parts voids this warranty. The fireplace MUST be installed by a  
qualified installer in accordance with all local codes and instructions furnished with the unit.  
Thiswarrantydoesnotapplytopartsthatarenotinoriginalconditionbecauseofnormalwearandtear,orpartsthatfailorbecomedamaged  
as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor,  
transportation and any and all such other costs related to repairing a defective fireplace will be the responsibility of the owner.  
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE  
PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND  
LIMITSTHEDURATIONOFANYANDALLIMPLIEDWARRANTIES,INCLUDINGWARRANTIESOFMERCHANTA-  
BILITY AND FITNESS FOR A PARTICULAR PURPOSE TO FOUR (4) YEARS ON ALL COMPONENTS AND FIVE (5)  
YEARS ON STAINLESS STEEL BURNERS FROM THE DATE OF FIRST PURCHASE; AND DESA INTERNATIONAL’S  
LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA INTERNATIONAL  
SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR  
CONSEQUENTIAL DAMAGES.  
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or  
consequentialdamages, sotheabovelimitationonimpliedwarranties, orexclusionorlimitationondamagesmaynotapplytoyou.  
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.  
For information about this warranty write:  
INTERNATIONAL  
2701 Industrial Drive  
P.O. Box 90004  
Bowling Green, KY 42102-9004  
107031-01  
REV. A  
107031 01  
03/00  
NOT A UPC  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Technics CD Player SC HD310 User Manual
Toshiba All in One Printer e Studio45 35 User Manual
Toshiba Flat Panel Television AM40 User Manual
Toshiba Laptop A135 S4477 User Manual
Triarch Indoor Furnishings 23174 User Manual
TTE Technology Flat Panel Television LE32HDF3010 User Manual
Ultra Products Home Theater Screen ULT33047 User Manual
Vermont Casting Indoor Fireplace DVT38S2 User Manual
ViewSonic Car Video System VA2038w LED User Manual
Vornado Fan ULTRA3 User Manual