User’s manual
Models:
CS6519/CS6519-14/
CS6519-15/CS6519-16/
CS6519-17/CS6519-19/
CS6519-2
BC
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Parts checklist
Your telephone contains the following items. Save your sales receipt and original
packaging in the event warranty service is necessary.
Handset
Charger and
Telephone base
charger adapter
(1 for CS6519//CS6519-
14/CS6519-15/CS659-16/
CS6519-17/CS6519-19)
(2 for CS6519-2)
(1 for CS6519-2)
Telephone
line cord
Telephone base
power adapter
Battery compartment cover
(1 for CS6519//CS6519-
14/CS6519-15/CS659-16/
CS6519-17/CS6519-19)
(2 for CS6519-2)
Abridged user’s manual
Battery
Abridged user’s manual
Wall mount bracket
(1 for CS6519//CS6519-14/
CS6519-15/CS659-16/
CS6519-17/CS6519-19)
(2 for CS6519-2)
To purchase a replacement battery or power adapter, visit our website at
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Telephone base and charger installation
Install the telephone base and charger as shown below.
If you subscribe to digital subscriber line (DSL) high-speed Internet service through
your telephone line, you must install a DSL filter between the telephone line cord and
telephone wall jack. Contact your DSL service provider for more information about
DSL filter.
Telephone wall jack
Electrical outlet
(not controlled
by a wall switch)
A DSL filter (not
included) is required
if you have DSL
high-speed Internet
service.
Electrical outlet
(not controlled
by a wall switch)
The DSL filter must
be plugged into the
telephone wall jack.
Telephone
base power
adapter
Charger
adapter
Telephone line cord
Charger
Telephone base
• Use only the power adapters supplied with this product. To order a replacement, visit our
• The power adapters are intended to be correctly oriented in a vertical or floor mount
position. The prongs are not designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Battery installation
Install the battery as shown below.
1. Plug the battery connector securely
into the socket, matching the
2. Place the battery with the label
THIS SIDE UP facing up and
the wires inside the battery
compartment.
orientation of the engraved label.
3. Slide the battery compartment cover
towards the center of the handset
until it clicks into place.
4. Place the handset in the telephone
base or charger to charge.
CHARGE light
remains on
when charging.
• If the handset will not be used for a long period of time, disconnect and remove the
battery to prevent any possible leakage.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Battery charging
Once you have installed the battery, the screen indicates the battery status
(see the table below).
•
For best performance, keep the handset in the telephone base or charger when not
in use.
•
•
The battery is fully charged after 11 hours of continuous charging.
If you place the handset in the telephone base or the charger without plugging in the
battery, the screen displays NO BATTERY
Battery indicators
Battery status
Action
The screen is blank, or
displays Put in charger and
flashes.
The battery has no or very
little charge. The handset
cannot be used.
Charge without interruption
(at least 30 minutes).
The screen displays
Low battery and
flashes.
The battery has enough
charge to be used for a short (about 30 minutes).
time.
Charge without interruption
The screen displays
HANDSET X.
The battery is charged.
To keep the battery charged,
place it in the telephone
base or charger when not
in use.
When the battery is fully charged, you can expect the following performance:
Operation
Operating time
Up to 7 hours
While in handset use (talking*)
While in speakerphone mode (talking*)
While not in use (standby**)
Up to 3.5 hours
Up to 5 days
*Operating times vary depending on your actual use and the age of the battery.
**Handset is not charging or in use.
After you install your telephone or power returns following a power outage,
the handset will prompt you to set the date and time. For instructions, see
Set date and time on page 12. To skip setting, press CANCEL.
Date: MM/DD/YY
ECO
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Installation options
The telephone comes ready for tabletop use. If you want to mount your telephone
on a wall, use the provided wall mount bracket to connect with a standard
dual-stud telephone wall mount plate. If you do not have this wall mount plate, you can
purchase one from many hardware or consumer electronics retailers. You may need a
professional to install the wall mount plate.
Tabletop to wall mount installation
1. Remove the telephone line cord
from the telephone wall jack, and
the telephone base power adapter
from the electrical outlet
2. Position the telephone base against
the wall mount bracket with the
extended tabs marked B on top.
Insert the extended tabs marked B on
the wall mount bracket into the slots
marked B on the back of the telephone
base. Push the telephone base down
until it clicks securely.
(if necessary).
3. Route the telephone line cord
through the hole on the wall
mount bracket and plug it into the
telephone wall jack. Route the
power cord out of the telephone
base and plug it into an electrical
outlet not controlled by a
4. Align the holes on the bracket with
the standard wall plate and slide the
bracket down until it locks securely.
Bundle the telephone line cord
and power adapter cord neatly
with twist ties.
wall switch.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Wall mount to tabletop installation
1. If the telephone line cord and power adapter cord are bundled, untie them first.
2. Slide the wall mount bracket up and remove it from the wall mount plate. Unplug the
telephone line cord (or DSL filter) from the telephone wall jack. Unplug the power
adapter from the power outlet.
3. Slide the telephone base up and remove it from the wall mount bracket.
4. See Telephone base and charger installation on page 2.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Telephone base layout
IN USE light
• Flashes when there is an incoming call, or
another telephone sharing the same line is
in use.
• Flashes when handsets are being deregistered.
• On when a handset is in use.
• On when a handset is being registered.
/FIND HANDSET
• Press to page all system handsets (page 23).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Handset layout
CHARGE light
• On when the handset is charging in the telephone
base or charger (page 3).
/ / VOLUME
• Press to review the directory when the phone is not
in use (page 30).
• During a call, press to increase the listening volume
(page 19).
• Press to scroll up while in a menu, or reviewing the
directory, caller ID log or redial list.
• While entering numbers or names in the directory,
press to move the cursor to the right.
REDIAL/PAUSE
• Press repeatedly to review the last 10 numbers dialed
(page 20).
• While dialing or entering numbers, press and hold to
insert a dialing pause (page 18 or page 28).
/FLASH
• Press to make or answer a call (page 18).
• During a call, press to answer an incoming call
when you receive a call waiting alert (page 19).
1
• While reviewing a caller ID log entry, press repeatedly
to add or remove 1 in front of the caller ID log entry
before dialing or saving it to the directory (page 37).
• Press and hold to set or dial your voicemail number
(page 14 or page 21).
Dialing keys
• Press to enter numbers or characters.
• Press to answer an incoming call (page 18).
TONE
• While on a call, press to switch to tone dialing
temporarily when using pulse service (page 20).
• Press to make or answer a call using the handset
speakphone (page 18).
• During a call, press to switch between the handset
speakerphone and the cordless handset (page 18).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Handset layout
CID/ /VOLUME
• Press to review the caller ID log when the phone is
• During a call, press to decrease the listening volume
• Press to scroll down while in a menu, or reviewing
the directory, caller ID log or redial list.
• While entering numbers or names in the directory,
press to move the cursor to the left.
MENU/SELECT
• Press to show the menu (page 10).
• While in a menu, press to choose an item, or save an
entry or setting.
OFF/CANCEL
• During a call, press to hang up.
• While the handset is ringing, press to silence the
ringer temporarily (page 19).
• Press and hold to erase the missed call indicator
when the phone is not in use (page 35).
• While in a menu, press to return to the previous
menu, or press and hold to return to idle mode,
without making changes.
MUTE/DELETE
• While on a call, press to mute the microphone
(page 19).
• While using the dialing keys, press to delete digits or
characters (page 18 and page 28).
• While the handset is ringing, press to silence the
ringer temporarily (page 19).
• When reviewing the directory, caller ID log or redial
list, press to delete the displayed entry (page 31,
page 39 or page 20).
QUIET#
• Press and hold to set and turn on the quiet mode, or
turn it off (page 11).
• Press repeatedly to show other dialing options when
reviewing a caller ID log entry (page 37).
INT
• Press to start an intercom conversation or transfer
a call (for multi-handset models only) (page 25 and
page 26).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone settings
Using the menu
You can use a cordless handset to change the telephone settings.
In the ringers menu, you can select the ringer tones and adjust the ringer volume for
incoming calls.
In the settings menu, you can change the settings for LCD language, voicemail
number, voicemail indicators, key tone, home area code and dial mode.
To enter the handset menu:
1. Press MENU when the phone is not in use.
2. Press or until the handset displays the desired
feature menu.
3. Press SELECT to enter that menu.
• To return to the previous menu, press CANCEL.
• To return to idle mode, press and hold CANCEL.
Ringer volume
You can adjust the ringer volume or turn the ringer off on each handset.
When the ringer is turned off, the handset displays and Ringer off.
1. Press MENU when the handset is not in use.
Ringers
2. Press or until the handset displays Ringers,
ECO
then press SELECT.
3. The handset displays Ringer volume, then press
SELECT again.
Ringer volume
4. Press or to sample each ringer volume level.
ECO
5. Press SELECT to save your selection. You hear a
confirmation tone.
Volume:
The ringer volume also determines the ringer volume for
intercom calls. If the ringer volume is set to off, that handset
ECO
is silenced for all incoming calls except paging tone.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone settings
Ringer tone
You can choose from different ringer tones on each handset.
1. Press MENU when the handset is not in use.
Ringers
2. Press or until the handset displays Ringers,
ECO
then press SELECT.
3. Press or until the handset displays Ringer tone,
then press SELECT.
Ringer tone
4. The handset displays Tone: with the current setting
ECO
displayed. Press or to sample each ringer tone.
5. Press SELECT to save your selection. You hear a
confirmation tone.
Tone: 1
If you turn off the ringer volume, you will not hear ringer
tone samples.
ECO
Quiet mode
You can turn on the quiet mode for a period of time (1-12
hours). During this period, all tones (except paging tone) are
muted.
To set the duration and turn on the quiet mode:
1. Press and hold QUIET# when the handset is not in use.
2. The handset displays Quiet: _ _ hours. Use the dialing
keys (0-9) to enter the desired duration (1-12).
Quiet: __ hours
[1-12]
3. Press SELECT to save. You hear a confirmation tone.
ECO
The handset displays Quiet mode on and
.
To turn off the quiet mode:
Quiet mode on
• Press and hold QUIET# when the handset is not in use. The
handset displays Quiet mode off briefly and then returns to idle.
ECO
10:15PM
12/25
When you change the settings of the ringer tone or ringer volume,
you can still hear the samples even if the quiet mode is on.
Quiet mode off
ECO
10:15PM
12/25
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone settings
Set date and time
If you subscribe to caller ID service, the day, month and time are set automatically with
each incoming call. You can also set the date and time manually.
1. Press MENU when the handset is not in use.
Set date/time
2. Press or until the handset displays Set date/time,
ECO
then press SELECT.
3. Press or to select the month then press SELECT,
or use the dialing keys to enter a two-digit number (01-12).
Date: MM/DD/YY
4. Press or to select the date then press SELECT,
ECO
or use the dialing keys to enter a two-digit number (01-31).
5. Press or to select the year then press SELECT,
or use the dialing keys to enter a two-digit number (00-99)
Time: HH:MM --
then press SELECT.
ECO
6. Press or to select the hour then press SELECT,
or use the dialing keys to enter a two-digit number (01-12).
7. Press or to select the minute then press SELECT,
or use the dialing keys to enter a two-digit number (00-59).
8. Press or to select AM or PM.
9. Press SELECT to save the settings. You hear a confirmation tone.
The phone plays two beeps if you enter an invalid number.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone settings
LCD language
You can select English, French or Spanish to be used in all screen displays.
1. Press MENU when the handset is not in use.
Settings
2. Press or until the handset displays Settings,
ECO
then press SELECT.
3. Press SELECT to choose LCD language.
LCD language
4. Press or to choose English, Français or Español,
then press SELECT.
ECO
• The screen displays Set English? when you
choose English.
English
• The screen displays Set Francais? when you
choose Français.
ECO
• The screen displays Set Espanol? when you
choose Español.
5. Press SELECT to save your selection. You hear a confirmation tone.
If you accidentally change the LCD language to French or Spanish, you can reset it to
.
English easily by pressing MENU then entering 364#
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone settings
Voicemail number
If you subscribe to voicemail service offered by your telephone service provider,
you can save the voicemail number to
When you want to retrieve voicemail messages, press and hold
1 on each handset for easy access.
1. Contact your
telephone service provider for more information and assistance about using your
voicemail service.
To set your voicemail number:
1. Press and hold
1 when the phone is not in use.
2. Use the dialing keys to enter the voicemail number (up to
30 digits).
• Press or to move the cursor to the left or right.
• Press DELETE to erase a digit.
• Press and hold DELETE to erase all digits.
• Press and hold PAUSE to insert a dialing pause (a P appears).
3. Press SELECT to save. Then the handset dials the saved voicemail number.
-OR-
Settings
1. Press MENU when the handset is not in use.
2. Press or to scroll to Settings, then press SELECT.
ECO
3. Press or to scroll to Voicemail #, then press SELECT.
4. Use the dialing keys to enter the voicemail number
Voicemail #
(up to 30 digits).
ECO
• Press or to move the cursor to the left or right.
• Press DELETE to erase a digit.
• Press and hold DELETE to erase all digits.
Voicemail #
-
• Press and hold PAUSE to insert a dialing pause
ECO
(a P appears).
5. Press SELECT to save. The handset displays VM # saved
and the stored number. You hear a confirmation tone.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone settings
Clear voicemail
If you subscribe to voicemail service offered by your telephone service provider,
the handsets display New voicemail and
when you have new voicemail
messages. Contact your telephone service provider for more information about
using your voicemail service.
After you have listened to all new voicemail messages, the indicators on the handsets
turn off automatically.
Use the clear voicemail feature when the telephone indicates that there is new
voicemail but there are none (for example, when you have accessed your voicemail
while away from home). The clear voicemail feature only turns off the indicators;
it does not delete your voicemail messages. As long as you have new voicemail
messages, your telephone service provider continues to send the signal to turn on
the indicators.
To manually turn off these indicators:
Settings
1. Press MENU when the handset is not in use.
ECO
2. Press or until the handset displays Settings,
then press SELECT.
Clr voicemail
3. Press or until the handset displays Clr voicemail,
then press SELECT. The handset displays Reset VM Icon?
ECO
4. Press SELECT to save your selection. You hear a
confirmation tone.
Reset VM Icon?
Your telephone service provider may alert you of new messages
with a stutter (broken) dial tone. Contact your telephone service
ECO
provider for details.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone settings
Key tone
You can turn the key tone on or off for each handset.
Settings
If you turn the key tone on, the handset beeps with each key
press. If you turn the key tone off, there are no beeps when you
press the handset keys.
ECO
1. Press MENU when the handset is not in use.
Key tone
2. Press or until the handset displays Settings,
ECO
then press SELECT.
3. Press or until the handset displays Key tone,
then press SELECT.
Key tone:On
4. Press or to choose Key tone:On or Key tone:Off.
ECO
5. Press SELECT to save your selection. You hear a
confirmation tone.
Home area code
If you dial local calls using only seven digits (area code not required), you can program
your home area code so that when you receive a call within your local area, the
telephone number is automatically stored in the caller ID log without the area code.
1. Press MENU when the phone is not in use.
Settings
2. Press or until the handset displays Settings,
ECO
then press SELECT.
3. Press or until the handset displays Home area code,
then press SELECT.
Home area code
4. Use the dialing keys (0-9) to enter the desired home
ECO
area code.
• Press DELETE to delete a digit.
Home area code
• Press and hold DELETE to delete all digits.
---
5. Press SELECT to save. You hear a confirmation tone.
ECO
If, in the future, your telephone service provider requires you to dial
the area code when making a local call, or, if you move to a location
that requires it, follow the steps above to delete the home area code
you have already programmed. After you have deleted the home
area code, _ _ _ appears.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone settings
Dial mode
The dial mode is preset to touch-tone dialing. If you have pulse
(rotary) service, you must change the dial mode to pulse dialing
before using the telephone to make a call.
Settings
ECO
1. Press MENU when the phone is not in use.
2. Press or until the handset displays Settings,
Dial mode
then press SELECT.
ECO
3. Press or until the handset displays Dial mode,
then press SELECT.
4. Press or to choose Touch-tone or Pulse.
Touch-tone
5. Press SELECT to save your selection. You hear a
ECO
confirmation tone.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone operation
Make a call
1. Press
or on the handset.
2. When you hear a dial tone, dial the number with the dialing
keys (0-9).
• The screen displays the elapsed time as you talk (in hours,
minutes and seconds).
• While entering numbers, press and hold PAUSE to insert a
dialing pause (a P appears).
Predial a call
1. Enter the number with the dialing keys (0-9).
2. Press
or to dial.
• The screen displays the elapsed time as you talk (in hours, minutes and seconds).
• While predialing, press DELETE or CANCEL to backspace and delete; press and hold
PAUSE to insert a dialing pause (a P appears).
Answer a call
• Press
,
or any dialing key (0-9, TONE or QUIET ).
#
End a call
• Press OFF or put the handset to the telephone base or charger.
Speakerphone
During a call, press to switch between speakerphone and
normal handset use.
When the speakerphone is active, the handset
displays Speaker.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone operation
Volume
During a call, press /VOLUME or /VOLUME to adjust the
listening volume.
When the volume reaches the minimum or maximum setting,
you hear two beeps.
The handset earpiece and speakerphone volume settings
are independent.
Mute
The mute function allows you to hear the other party but the other party cannot
hear you.
• During a call, press MUTE. The handset displays Muted until the
Muted
mute function is turned off.
ECO
• Press MUTE again to resume the conversation. The handset
displays Microphone on briefly.
10:15PM
12/25
Call waiting
When you subscribe to call waiting service from your telephone service provider, you
hear an alert tone if there is an incoming call while you are already on another call.
• Press FLASH to put the current call on hold and take the new call.
• Press FLASH at any time to switch back and forth between calls.
Temporary ringer silencing
When the telephone is ringing, you can temporarily silence the handset ringer without
disconnecting the call. The next call rings normally at the preset volume.
• Press OFF or MUTE, then displays and Ringer muted
Ringer muted
displays briefly.
ECO
Each handset rings when there is an incoming call unless the ringer
volume of that handset is turned off.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone operation
Temporary tone dialing
If you have pulse (rotary) service only, you can switch from pulse to touch-tone dialing
temporarily during a call. This is useful if you need to send touch-tone signals to
access your telephone banking or long distance services.
1. During a call, press TONE .
2. Use the dialing keys to enter the number. The telephone sends touch-tone signals.
It automatically returns to pulse dialing mode after you end the call.
Redial
Each handset stores the last 10 telephone numbers dialed.
• When there are already 10 entries, the oldest entry is deleted to make room for the
new entry.
• Entries are in reverse chronological order.
• The handset plays two beeps when you reach the end or beginning of the redial list,
or when you access the redial list with no records.
To review and dial a redial entry:
1. Press REDIAL when the phone is not in use.
2. Press
,
or REDIAL repeatedly until the desired
entry displays.
3. Press
or to dial.
-OR-
1. Press
or when the phone is not in use.
2. Press REDIAL and then press
,
or REDIAL repeatedly
Redial #2/10
until the desired entry displays.
800-595-9511
ECO
3. Press SELECT to dial.
To delete a redial entry:
1. Press REDIAL when the handset is not in use.
2. Press or REDIAL repeatedly to browse to the desired entry.
,
3. Press DELETE to delete the displayed number. You hear a confirmation tone.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone operation
Check voicemail
Press and hold
1 to dial your voicemail number.
See Voicemail number on page 14.
Chain dialing
Use this feature to initiate a dialing sequence from numbers stored in the directory,
caller ID log or redial list while you are on a call. Chain dialing can be useful if you wish
to access other numbers (such as bank account numbers or access codes) from the
directory, caller ID log or redial list.
To access a number in the directory:
1. Press MENU while on a call.
2. Press SELECT to choose Directory.
3. Press or to scroll to the desired entry.
4. Press SELECT to dial the displayed number.
To access a number in the caller ID log:
1. Press MENU while on a call.
2. Press or to scroll to Caller ID log, then press SELECT.
3. Press or to scroll to the desired entry.
4. Press SELECT to dial the displayed number.
To access a number on the redial list:
1. Press REDIAL while on a call.
2. Press
,
or REDIAL repeatedly to browse to the desired entry.
3. Press SELECT to dial the displayed number.
Press CANCEL to exit the directory, caller ID log or redial list when you are on a call.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone operation
Web address
Web address
Use this feature to view the VTech website address.
1. Press MENU when the handset is not in use.
ECO
2. Press or until the handset displays Web address,
then press SELECT. The handset displays the VTech
website address.
ECO
Transfer a call
.com
While on an outside call, you can transfer the call from one
handset to another.
ECO
1. During a call, press MENU.
2. Press or to scroll to Transfer, then press SELECT.
• If you have two handsets, your handset displays
Transfer
Calling HS X and then Transferred.
ECO
• If you have three or more handsets, your handset
displays Transfer to: Use the dialing keys to select a
destination handset. Your handset displays Calling HS X
and then Transferred.
Transfer to:
The destination handset rings and its screen displays
ECO
Incoming call.
3. To answer on the destination handset, press
,
,
Calling HS X
or any dialing key (0-9, TONE or QUIET ) on the
#
destination handset.
ECO
• If the destination handset does not answer the call within
30 seconds, the call will be reverted to the originating handset.
If you do not press
,
, or any dialing key (0-9, TONE or
Transferred
QUIET ) on your handset to reconnect the outside call within
#
30 seconds, the call ends automatically.
ECO
• If the destination handset is in the directory or caller ID log, or
is out of range, the originating handset displays Unable to call
and then reconnects to the outside call.
Incoming call
ECO
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone operation
Find handset
Use this feature to find all system handsets.
To start paging:
• Press /FIND HANDSET on the telephone base when not
in use. All idle handsets ring and display Paging
.
**
**
To end paging:
• Press /FIND HANDSET on the telephone base.
-OR-
• Press
,
, OFF or any dialing key (0-9, TONE or QUIET ) on a handset.
#
-OR-
• Place the handset in the telephone base or charger.
• Do not press and hold /FIND HANDSET for more than 4 seconds. It may lead to
handset deregistration.
• Press MUTE to turn off the ringer of a handset temporarily. Paging tone continues
on all other handsets.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Multiple handset use
Join a call in progress
You can use up to two handsets at the same time on an outside call.
You can buy additional expansion handsets (CS6509/CS6509-14/CS6509-15/
CS6509-16) for this telephone base. You can register up to five handsets to the
telephone base.
To share an outside call:
• When a handset is already on a call and you would like to join the call, press
or on the other handset.
• To exit the call, press OFF or place the handset in the telephone base or charger.
The call continues until both handsets hang up.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Multiple handset use
Intercom
Use the intercom feature for conversations between two handsets. You can buy
additional expansion handsets (CS6509/CS6509-14/CS6509-15/CS6509-16) for this
telephone base. You can register up to five handsets to the telephone base.
1. Press INT on your handset when not in use.
Calling HS X
• If you have only one handset, your handset displays
ECO
INT needs 2 HS.
• If you have two handsets, your handset displays
Calling HS X.
HS X is calling
• If you have three or more handsets, your handset displays
ECO
Intercom to. Use the dialing keys to enter a destination
handset. Your handset displays Calling HS X.
The destination handset rings and its screen displays
HS X is calling.
Intercom
ECO
2. To answer the intercom call, press
,
, INT or any dialing key
(0-9, TONE or QUIET ) on the destination handset.
#
Both handsets now display Intercom.
3. To end the intercom call, press OFF or place the handset back in the telephone
base or charger. Both handsets now display Intercom ended.
• You can cancel the intercom call before it is answered by pressing OFF or INT on the
originating handset.
• If the destination handset does not answer the intercom call within 100 seconds, is
on a call or out of range, the originating handset displays Unable to call and returns to
idle mode.
• Press OFF or MUTE on the destination handset to temporarily silence the intercom ringer.
• You can use four handsets on two pairs of intercom calls. For example, when four
handsets are used on two pairs of intercom calls, use the fifth handset for an outside call.
• If there is an incoming call while the originating handset displays Calling HS X,
the intercom request will be stopped and the handset displays Incoming call.
Answer an incoming call during an intercom call
When you receive an outside call during an intercom call, there is an alert tone.
• To answer the outside call, press . The intercom call ends automatically.
• To end the intercom call without answering the outside call, press OFF.
The telephone continues to ring.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Multiple handset use
Call transfer using intercom
Use the intercom feature to transfer an outside call to another
system handset.
Intercom to
ECO
1. During a call, press INT.
• If you have two handsets, the outside call is put on hold
and your handset displays Calling HS X.
Calling HS X
• If you have three or more handsets, your handset displays
Intercom to. Use the dialing keys to enter a handset
number. The outside call is put on hold and your handset
displays Calling HS X.
ECO
HS X is calling
The destination handset rings and its screen displays
ECO
HS X is calling.
2. To answer the intercom call on the destination handset, press
,
, INT or any dialing key (0-9, TONE or QUIET#). The
Intercom
outside call is still on hold and both handsets now display
Intercom. You can now have a private conversation with the
destination handset.
ECO
• To cancel the intercom call before it is answered, press OFF,
or INT on your handset.
• If the destination handset does not answer within 100 seconds, is in use, on a call or is
out of range, the originating handset displays Unable to call and then reconnects to the
outside call.
3. From this intercom call, you have the following options:
• You can let the destination handset join you on the outside call in a
three-way conversation. Press and hold INT on the originating handset.
• You can transfer the call. Press OFF, or place your handset back in the
telephone base or charger. Your handset displays Transferred. The destination
handset is then connected to the outside call.
• You can press INT to switch between the outside call (Outside call displays) and
the intercom call (Intercom displays).
• The destination handset can end the intercom call by pressing OFF, or by placing
the handset back in the telephone base or charger. The outside call continues
with the original system handset.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Directory
About the directory
The directory can store up to 50 entries which are shared by all
system handsets. Each entry may consist of a phone number up
to 30 digits and a name up to 15 characters.
Directory empty
ECO
• Directory entries are shared by all system handsets.
Any modifications made on one handset apply to all
system handsets.
Directory full
• When you access the directory without records, the screen
ECO
displays Directory empty.
• When the directory is full and you try to save an entry,
Number repeated
the screen displays Directory full.
ECO
• When you try to save an entry already stored in the directory,
the screen displays Number repeated.
• When the telephone number in the directory exceeds 15 digits,
a dash appears after the 14th digit, and the remaining digits are
displayed after two seconds beginning with a dash.
Mike Smith
12345678901234-
ECO
• Only one handset can review the directory at a time. When a
handset tries to enter the directory while another handset is
already in it, Not available appears.
Mike Smith
-567
ECO
Not available
ECO
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Directory
Add a directory entry
1. Press MENU when the phone is not in use.
2. Press or to scroll to Directory, then press SELECT.
3. Press SELECT to choose Add contact.
Directory
ECO
4. When Enter number displays, use the dialing keys to enter a
Add contact
number (up to 30 digits).
• Press or to move the cursor to the left or right.
• Press DELETE to backspace and erase a digit.
• Press and hold DELETE to erase all digits.
ECO
Enter number
-
• Press and hold PAUSE to enter a dialing pause
ECO
(a P appears).
-OR-
Enter name
Copy a number from the redial list by pressing REDIAL.
Then press
,
or REDIAL repeatedly to find the desired
ECO
number. Press SELECT to copy the number.
5. Press SELECT to move on to the name.
Mike_
6. When Enter name displays, use the dialing keys to enter a
name (up to 15 characters). Each time you press a key, the
character on that key appears. Additional key presses produce
other characters on that key. Press the key repeatedly until the
desired character appears. The first character of each word
is capitalized.
ECO
• Press or to move the cursor to the left or right.
• Press 0 to add a space.
• Press DELETE to backspace and erase a character.
• Press and hold DELETE to erase all characters.
7. Press SELECT to confirm. The handset displays Saved and then you hear a
confirmation tone.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Directory
Add a directory entry
-OR-
1. Use the dialing keys to enter a number (up to 30 digits)
when the phone is not in use. Press SELECT. The handset
displays Enter number.
Enter number
800-595-9511
ECO
-
• Press or to move the cursor to the left or right.
• Press DELETE to backspace and erase a digit.
• Press and hold DELETE to erase all digits.
Enter name
ECO
• Press and hold PAUSE to enter a dialing pause
(a P appears).
-OR-
Mike_
Copy a number from the redial list by pressing REDIAL.
ECO
Then press
,
or REDIAL repeatedly to find the desired
number. Press SELECT to copy the number.
2. Press SELECT to move on to the name.
3. When Enter name displays, use the dialing keys to enter a name (up to
15 characters). Each time you press a key, the character on that key appears.
Additional key presses produce other characters on that key. Press the key
repeatedly until the desired character appears. The first character of each word
is capitalized.
• Press or to move the cursor to the left or right.
• Press 0 to add a space.
• Press DELETE to backspace and erase a character.
• Press and hold DELETE to erase all characters.
4. Press SELECT to confirm. The handset displays Saved and then you hear a
confirmation tone.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Directory
Review and dial from the directory
Entries are sorted alphabetically.
1. Press when the phone is not in use. The handset displays
Review
Entries in DIR X and then the first entry in the directory.
ECO
2. Press or to browse. When the desired entry displays,
press
or
to dial.
-OR-
Entries in DIR
8
1. Press MENU when the phone is not in use.
ECO
2. Press or to scroll to Directory then press SELECT.
3. Press or to scroll to Review and then press SELECT.
The handset displays Entries in DIR X and then the first entry
in the directory.
Mike Smith
800-595-9511
ECO
4. Press or to browse. When the desired entry displays,
press
or
to dial.
Alphabetical search
To start an alphabetical search:
1. Press when the phone is not in use. The handset displays Entries in DIR X
and then the first entry in the directory.
-OR-
i. Press MENU when the phone is not in use.
ii. Press or to scroll to Directory, then press SELECT.
iii. Press or to scroll to Review, then press SELECT. The handset displays
Entries in DIR X and then the first entry in the directory.
2. Use the dialing keys to enter the letter associated with the name. For example,
if you have entries for Jenny, Jessie, Kristen and Laura in your directory, press 5
(JKL) once to see Jenny (when Jenny displays, press to see Jessie), twice to
see Kristen, or three times to see Laura. If there is no name entry matching your
search, the next closest match in alphabetical order appears. If necessary, press
or to browse.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Directory
Edit a directory entry
1. Search for the desired entry in the directory (see Review and dial from the
directory or Alphabetical search on page 30).
2. When the desired entry appears, press SELECT. The handset
Edit number
displays Edit number and the stored number.
800-595-9511_
ECO
3. Use the dialing keys to edit the number.
• Press DELETE to backspace and erase a digit.
• Press and hold DELETE to erase the entire entry.
• Press or to move the cursor to the left or right.
• Press and hold PAUSE to insert a dialing pause (a P appears).
4. Press SELECT to move on to edit the name. The handset
Edit name
displays Edit name and then the stored name.
ECO
5. Use the dialing keys to edit the name (up to 15 characters).
Additional key presses show other characters of that
particular key.
Mike Smith_
• Press DELETE to backspace and erase a character.
• Press and hold DELETE to erase the entire entry.
• Press or to move the cursor to the left or right.
• Press 0 to add a space.
ECO
6. Press SELECT to confirm. The handset displays Saved and then you hear a
confirmation tone.
Delete a directory entry
Delete contact?
800-595-9511
1. Search for the desired entry in the directory (see
Review and dial from the directory or Alphabetical search
on page 30).
ECO
2. When the desired entry appears, press DELETE. The handset
Deleting...
displays Delete contact? and the number.
ECO
3. Press SELECT to confirm. The handset displays Deleting ...
and then Contact deleted. You hear a confirmation tone.
Contact deleted
ECO
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Directory
Speed dial
You can copy up to 9 directory entries into the speed dial locations (0 and 2-9) so that
you can dial these numbers using fewer keys than usual.
The speed dial memory locations are stored in the telephone base and are shared by
all handsets. Changes made to the speed dial entries on one handset apply to all.
Assign a speed dial entry
1. Press MENU when the phone is not in use.
0:<Unassigned>
2. Press or to scroll to Directory, then press SELECT.
ECO
3. Press or to scroll to Speed dial, then press SELECT.
4. Press or or the dialing keys (0 or 2-9) to choose the
Copy from DIR...
desired speed dial location.
5. Press SELECT. The handset displays Copy from DIR...
ECO
and then the first entry in the directory.
6. Press or to browse to the desired entry.
Mike Smith
-OR-
800-595-9511
ECO
Use the alphabetical search to find the desired entry
(see page 30).
7. Press SELECT to save. You hear a confirmation. The name
0:Mike Smith
(up to 12 characters) appears in the selected speed
dial location.
ECO
• If the directory is empty, when you press SELECT in Step 5,
the handset displays Directory empty.
• If the speed dial location you selected is occupied, the new directory
entry you selected replaces the old one. Take caution not to replace
entries you do not wish to delete from the speed dial locations.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Directory
Reassign a speed dial entry
1. Press MENU when the phone is not in use.
Directory
2. Press or to scroll to Directory, then press SELECT.
3. Press or to scroll to Speed dial, then press SELECT.
ECO
4. Press or , or use the dialing keys to choose the speed dial
location you want to reassign.
Speed dial
5. Press SELECT twice. The handset displays Reassign SD.
ECO
6. Press SELECT. The handset displays Copy from DIR... and
then the first entry of the directory.
Reassign SD
7. Press or to browse to the desired entry.
ECO
-OR-
Use the alphabetical search to find the desired entry
(see page 30).
Copy from DIR...
8. Press SELECT to save. You hear a confirmation. The name
ECO
(up to 12 characters) appears in the selected speed dial location.
Dial a speed dial number
• Press and hold a dialing key (0 or 2-9) to dial the number stored in the corresponding
speed dial location.
When the speed dial location is empty, the handset displays the speed dial list.
See Assign a speed dial entry on page 32 to add a new entry.
Delete a speed dial entry
Directory
1. Press MENU when the phone is not in use.
ECO
2. Press or to scroll to Directory, then press SELECT.
3. Press or to scroll to Speed dial, then press SELECT.
Speed dial
4. Press or , or use the dialing keys to choose the desired
speed dial location, then press DELETE. The handset displays
Clear SD #X?
ECO
5. Press SELECT to confirm. You hear a confirmation tone.
Clear SD #X?
Deleting the speed dial entries does not affect the entries in
the directory.
ECO
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID
About caller ID
This product supports caller ID services provided by most telephone service providers.
Depending on your service subscription, you may see the caller’s number, or the
caller’s name and number that are sent by your telephone service provider after the
first or second ring. Caller ID allows you to see the name, number, date and time
of calls.
Information about caller ID with call waiting
Caller ID with call waiting lets you see the name and telephone number of the caller
before answering the telephone, even while on another call.
It may be necessary to change your telephone service to use this feature. Contact
your telephone service provider if:
• You have both caller ID and call waiting, but as separate services (you may need to
combine these services).
• You have only caller ID service, or only call waiting service.
• You do not subscribe to caller ID or call waiting services.
There are fees for caller ID services. In addition, services may not be available in
all areas.
This product can provide information only if both you and the caller are in areas
offering caller ID service and if both telephone service providers use compatible
equipment. The time and date, along with the call information, are from the telephone
service provider.
You can use this product with regular caller ID service, or you can use this product’s
other features without subscribing to caller ID or combined caller ID with call
waiting service.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID
Caller ID log
If you subscribe to caller ID service, information about each caller will appear after the
first or second ring. If you answer a call before the caller information appears on the
screen, it will not be saved in the caller ID log.
• The caller ID log stores up to 50 entries. Each entry has up to 24 digits for the phone
number and 15 characters for the name. If the telephone number has more that
15 digits, only the last 15 digits appear. If the name has more than 15 characters,
only the first 15 characters are shown and saved in the caller ID log.
• You can review, redial and copy an entry into the directory.
• Entries appear in reverse chronological order.
• When the caller ID log is full, the oldest entry is deleted to make room for new
incoming call information.
• XX missed calls displays when you have incoming calls that have not
been answered.
• Call log empty displays when you access the caller ID log without records.
• Caller ID log entries are shared by all system handsets. Any deletions made on one
handset are reflected on all other handsets.
• Only one handset can review the caller ID log at a time. If a handset tries to enter the
caller ID log while another handset is already in it, Not available displays.
• For caller ID log entries with numbers between 16 and 24 digits, in order to view the
entire number, you must save the entry to the directory (see page 38).
• If the phone number has more than 24 digits, it will not be saved or shown in the
caller ID log.
Missed call indicator
When you have incoming calls that have not been answered,
the handset displays XX missed calls.
XX missed calls
ECO
Each time you review a caller ID log entry marked NEW,
the number of missed calls decreases by one.
10:15PM
12/25
When you have reviewed all the missed calls, the missed call
indicator no longer displays.
Mike Smith
595-9511
ECO
If you do not want to review the missed calls one by one,
press and hold CANCEL on the idle handset to erase the missed
call indicator. All the entries are then considered old and kept in the
caller ID log.
NEW
10:15PM
12/25
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID
Memory match
When the incoming telephone number matches the last seven digits of a telephone
number in your directory, the name that appears on the screen matches the
corresponding name in your directory.
For example, if Linda Jones calls, her name appears as Linda if this is how you
entered it into your directory.
The number shown in the caller ID log is in the format sent by the telephone service
provider. The telephone service provider usually delivers 10-digit phone numbers (area
code plus telephone number). If the phone number of the caller does not match a number
in your directory, the name will appear as it is delivered by the telephone service provider.
Review and dial from the caller ID log
1. Press CID when the phone is not in use. The handset displays
Caller ID log
Entries in CID X and then the first entry in the caller ID log.
ECO
2. Press or to browse.
3. When the desired entry displays, press
-OR-
or to call.
Review
1. Press MENU when the phone is not in use.
ECO
2. Press or to scroll to Caller ID log then press SELECT.
3. Press SELECT to choose Review.
Entries in CID
4. Press or to browse.
48
ECO
5. When the desired entry displays, press
or to call.
You hear a double beep when you reach the beginning or end of
the caller ID log.
Mike Smith
800-595-9511
ECO
10:15PM
12/25
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID
View dialing options
Although the caller ID log entries received have
10 digits (the area code plus the seven-digit number),
in some areas, you may dial only the seven digits, or a
1 plus the seven digits, or a 1 plus the area code plus
the seven digits. You can change the number of digits
that you dial from the caller ID log and store the new
number to the directory.
Mike Smith
800-595-9511
ECO
10:15PM
12/25
Press #
Press #
Press #
Press #
-OR-
Press 1
Press 1
1-800-595-9511
595-9511
1-595-9511
800-595-9511
While reviewing the caller ID log, press QUIET
#
repeatedly to show different dialing options for local
and long distance numbers before dialing or saving the
telephone number in the directory.
1-800-595-9511
800-595-9511
Press 1 repeatedly if you need to add or remove 1 in
front of the telephone number before dialing or saving it
in the directory.
When the number is shown in the correct format for dialing,
press
or to dial.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID
Save a caller ID log entry to the directory
1. Press CID when the phone is not in use.
-OR-
Press MENU when the phone is not in use. Press or to scroll to Caller ID log.
Then press SELECT twice.
2. When the desired entry appears, press SELECT. The handset
Edit number
displays Edit number and the stored number.
800-595-9511_
ECO
3. Use the dialing keys to edit the number.
• Press DELETE to backspace and erase a digit.
• Press and hold DELETE to erase the entire entry.
• Press or to move the cursor to the left or right.
• Press and hold PAUSE to insert a dialing pause (a P appears).
4. Press SELECT to move on to edit the name. The handset
Edit name
displays Edit name.
ECO
5. Use the dialing keys to enter the name (up to 15 characters).
Additional key presses show other characters of that
particular key.
• Press DELETE to backspace and erase a character.
• Press and hold DELETE to erase the entire entry.
• Press or to move the cursor to the left or right.
• Press 0 to add a space.
6. Press SELECT to confirm. The handset displays Saved and then you hear a
confirmation tone.
If you try to save an entry without caller ID information, the handset displays
Unable to save and you hear a double beep.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID
Delete the caller ID log entries
To delete an entry:
1. When in the caller ID log, press or to browse.
2. Press DELETE to delete the selected entry. The handset displays Deleting...
and then you hear a confirmation tone.
To delete all entries:
1. Press MENU when the phone is not in use.
Delete all?
2. Press or to scroll to Caller ID log, then press SELECT.
ECO
3. Press or to scroll to Del all calls, then press SELECT.
4. Press SELECT to confirm. The handset displays Deleting... and
then you hear a confirmation tone.
Caller ID log screen messages
Displays
When
The caller is blocking the name information.
PRIVATE NAME
The caller is blocking the telephone number information.
The caller is blocking the name and number information.
This caller’s name is unavailable.
PRIVATE NUMBER
PRIVATE CALLER
UNKNOWN NAME
This caller’s number is unavailable.
UNKNOWN NUMBER
UNKNOWN CALLER
No call information is available about this caller.
It is a long distance call.
LONG DISTANCE
-OR-
L(before the caller’s number)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Expand your telephone system
Your telephone base can support up to five handsets. Each handset must be
registered to the telephone base before use. The handsets provided within your
product package are already registered as HANDSET 1 and so forth. You can add
new handsets (CS6509/CS6509-14/CS6509-15/CS6509-16, purchased separately)
to your telephone base. Additional handsets are assigned numbers in the sequential
order they are registered (up to HANDSET 5).
Add and register a handset
When first purchased, each expansion handset displays To register HS and
See manual alternately. You may need to charge the handset before registering to
the telephone base. For more details on battery charging, see the table on page 4.
To register a handset:
1. Place the new/non-registered handset in the telephone base.
Do not place the handset
in the charger.
2. After about 10 seconds, the handset displays Registering... When the registration
process completes, the handset displays Registered and you hear a confirmation
tone. The registration process takes about 90 seconds to complete.
If the registration fails, the handset displays Failed and then To register HS and
See manual alternately, remove the handset from the telephone base and place it
back in. Try the registration process again.
• You cannot register a handset if any other system handset is in use.
• Only one handset can register to the telephone base at a time.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Replace a handset
If you want to replace a handset, or reassign the designated handset number of
a registered handset, you must deregister all handsets that are registered to the
telephone base. Then register each handset individually.
To make deregistration easier, read all of the instructions below before you begin.
To deregister all handsets:
1. Press and hold /FIND HANDSET on the telephone base for about 10 seconds until
the IN USE light on the telephone base turns on and starts to flash.
2. Immediately press /FIND HANDSET again. You must press /FIND HANDSET
while the IN USE light is still flashing. The IN USE light flashes for approximately
five seconds.
3. All handsets display To register HS and See manual alternately when the
deregistration process completes. The deregistration process takes about
10 seconds to complete.
To register the handset(s) to the telephone base again, follow the registration
instructions on the previous page.
• You cannot deregister all handsets if any other system handset is in use.
• If deregistration fails, you may need to reset the system and try again. To reset, unplug
the power from the telephone base and plug it back in.
• Even if the battery is depleted, you can still deregister all handsets by following the steps
above. After the handset is charged for at least 10 minutes, the handset alternately
shows To register HS and See manual.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Screen messages
There are no caller ID log entries.
Call log empty
Calling HS X
You are calling another handset (for intercom calls).
(for models with two or more
handsets only)
A directory entry is deleted.
Contact deleted
Directory empty
Directory full
There are no directory entries.
The directory is full. You cannot save any new entry unless you
delete some current entries.
You have just ended a call.
Ended
The handset registration is not successful.
Another handset is calling (for intercom calls).
Failed
HS X is calling
(for models with two or more
handsets only)
There is an incoming call.
Incoming call
INT needs 2 HS
Intercom
Two handsets are required for an intercom call.
The handset is on an intercom call.
The intercom call has just ended.
Intercom ended
Intercom to
(for models with three or more
handsets only)
You have started the intercom process or started transferring a
call, and need to enter the desired handset number.
A system handset or another telephone on the same line is
in use.
Line in use
The battery needs to be recharged.
Low battery
MUTE is turned off and the person on the other end can
hear you.
Microphone on
You have turned off the handset microphone. The other party
cannot hear you but you can hear the other party.
Muted
There are new voicemail message(s) from your telephone
service provider.
New voicemail
NO BATTERY
You place the handset in the telephone base or charger without
installing a battery in it.
There is no telephone line connected.
No line
Another handset is already in the directory or caller ID log.
Not available
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Screen messages
The telephone number you have entered is already stored in
the directory.
Number repeated
The telephone base has lost power, or the handset is out
of range.
Out of range or
no pwr at base
The handset is on a call.
Phone
The battery is very low. Put the handset in the telephone base
or charger for recharging.
Put in charger
The quiet mode is turned on.
Quiet mode on
Quiet mode off
Registering...
Ringer muted
Ringer off
Saved
The quiet mode is turned off.
The handset registration is in progress.
The handset ringer is muted temporarily during an incoming call.
The handset ringer is turned off.
Your selection has been saved.
The handset speakerphone is in use.
Screen display on a non-registered handset.
Speaker
To register HS
See manual
You have transferred an outside call to another cordless
handset.
Transferred
The handset is out of range while on a call.
Unable to call
Failed phone call (the telephone line is in use).
Failed intercom call (there are already two handsets being used).
There are new calls in the caller ID log.
All system handsets are being paged.
XX missed calls
** Paging **
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Handset and telephone base indicators
Handset lights
On when the handset speakerphone is in use.
CHARGE
On when the handset is charging in the telephone base or charger.
Telephone base lights
On when the telephone line is in use.
IN USE
On when you are registering a handset.
Flashes quickly when there is an incoming call.
Flashes when another telephone sharing the same line is in use.
Flashes when you are deregistering all handsets.
Handset icons
The battery icon flashes when the battery is low and needs charging.
The battery icon animates when the battery is charging.
The battery icon becomes solid when the battery is fully charged.
The speakerphone is in use.
The handset ringer is turned off.
There are new voicemail received from the telephone service provider.
The ECO mode activates automatically to reduce power consumption when the
handset is within range from the telephone base.
ECO
The entry you are reviewing is new in the caller ID log.
NEW
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
If you have difficulty with your telephone, please try the suggestions below. For customer
My telephone does not work at all.
•
Make sure the battery is installed and charged correctly (page 3). For optimum daily
performance, return the handset to the telephone base or charger after use.
•
Make sure the power adapter is securely plugged into an outlet not controlled by a
wall switch.
•
•
Make sure the telephone line cord is plugged firmly into the telephone base and the wall jack.
Unplug the electrical power to the telephone base. Wait for approximately 15 seconds,
then plug it back in. Allow up to one minute for the cordless handset and telephone base
to synchronize.
•
•
Charge the battery in the handset for up to 11 hours.
If the battery is completely depleted, charge the handset for at least 30 minutes before use
(page 4).
•
•
Remove and install the battery again. If that still does not work, it may be necessary to
purchase a new battery.
Disconnect the telephone base from the telephone wall jack and plug in a working telephone.
If the other telephone does not work, the problem is probably in the wiring or telephone
service. Contact your telephone service provider.
The display shows No line. I cannot get a dial tone.
Try all the above suggestions.
•
•
•
Make sure the telephone line cord is plugged firmly into the telephone base and the wall jack.
Disconnect the telephone line cord from your telephone and connect it to another telephone.
If there is no dial tone on that other telephone either, then the telephone line cord may be
defective. Try installing a new telephone line cord.
If changing the telephone line cord does not help, the wall jack (or the wiring to this wall jack)
may be defective. Contact your telephone service provider.
I cannot dial out.
•
•
Try all the above suggestions.
Make sure there is a dial tone before dialing. It is normal if the handset takes a second or two
to synchronize with the telephone base before producing a dial tone. Wait an extra second
before dialing.
•
•
If other telephones in your home are having the same problem, the problem is in the wiring or
telephone service. Contact your telephone service provider (charges may apply).
Eliminate any background noise. Mute the cordless handset before dialing, or dial from
To register HS and See manual appear alternately on the handset and it does not
work at all.
•
The handset may be deregistered from the telephone base. Refer to Add and register a
handset on page 40 to register the handset to the telephone base.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
My cordless handset isn’t performing normally.
•
Make sure you plug the power cord securely into the telephone base. Plug the power adapter
into a different, working electrical outlet without a wall switch.
•
•
Move the cordless handset closer to the telephone base. You may have moved out of range.
Reset the telephone base. Unplug the electrical power. Wait for 15 seconds then plug it back
in. Allow up to one minute for the cordless handset and telephone base to reset.
•
Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as possible
from these types of electronic devices.
Low battery shows on the handset screen.
•
•
Place the handset in the telephone base or charger for recharging.
Remove and install the battery again and use it until fully depleted, then charge the handset
in the telephone base or charger for up to 11 hours.
•
If the above measures do not correct the problem, replace the battery.
The battery does not charge in the handset or the handset battery does not
accept charge.
•
•
•
Make sure the handset is placed in the telephone base or charger correctly.
Remove and install the battery again, then charge for up to 11 hours.
If the battery is completely depleted, charge the handset for at least 30 minutes before use
(page 4).
•
Purchase a new battery. Refer to the Battery section (page 4).
The CHARGE light is off.
•
Clean the charging contacts on the handset, telephone base and/or charger each month with
a pencil eraser or a dry non-abrasive fabric.
•
•
Make sure the power adapter and telephone line cord are plugged in properly (page 2).
Unplug the power adapter. Wait for 15 seconds before plugging it back in. Allow up to one
minute for the handset and telephone base to reset.
The telephone does not ring when there is an incoming call.
•
•
•
•
Make sure the ringer volume of the handset is not set to off (page 10).
Make sure the telephone line cord and power adapter are plugged in properly (page 2).
The handset may be too far from the telephone base. Move it closer to the telephone base.
There may be too many extension phones on the telephone line to allow all of them to ring
simultaneously. Unplug some of them.
•
If other telephones in your home are having the same problem, the problem is in the wiring or
telephone service. Contact your telephone service provider (charges may apply).
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
•
Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as possible
from these types of electronic devices.
•
Test a working telephone at the telephone wall jack. If another telephone has the same
problem, the problem is in the telephone wall jack. Contact your telephone service provider
(charges may apply).
•
•
•
The telephone line cord may be defective. Install a new telephone line cord.
Remove and install the battery again and place the handset in the telephone base.
Wait for the handset to synchronize with the telephone base. Allow up to one minute for this
to take place.
There is interference during a telephone conversation.
My calls fade out when I am using the cordless handset.
•
•
The handset may be out of range. Move it closer to the telephone base.
If you subscribe to high-speed Internet service (DSL - digital subscriber line) through
your telephone line, you must install a DSL filter between the telephone line cord and
the telephone wall jack. The filter prevents noise and caller ID problems caused by DSL
interference. Contact your DSL service provider for more information about DSL filters.
•
•
Appliances or other cordless telephones plugged into the same circuit as the telephone base
can cause interference. Try moving the appliance or telephone base to another outlet.
Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as possible
from these types of electronic devices.
•
•
If your telephone is plugged in with a modem or a surge protector, plug the telephone (or
modem/surge protector) into a different location. If this doesn’t solve the problem, relocate
your telephone or modem farther apart from each other, or use a different surge protector.
The location of your telephone base can impact the performance of your cordless phone.
For better reception, install the telephone base in a centralized location within your home or
office, away from walls or other obstructions. In many environments, elevating the telephone
base improves overall performance.
•
•
Disconnect the telephone base from the telephone wall jack and plug in a corded telephone.
If calls are still not clear, the problem is probably in the wiring or telephone service. Contact
your telephone service provider (charges may apply).
If other telephones in your home are having the same problem, the problem is in the wiring or
telephone service. Contact your telephone service provider (charges may apply).
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
I get noise, static, or weak signals even when I’m near the telephone base.
•
If you subscribe to high-speed Internet service (DSL - digital subscriber line) through
your telephone line, you must install a DSL filter between the telephone line cord and
the telephone wall jack. The filter prevents noise and caller ID problems caused by
DSL interference. Contact your DSL service provider for more information about DSL filters.
•
•
You may be able to improve the performance of your cordless phone by installing your new
telephone base as far as possible from any other existing cordless telephone system that
may already be installed.
Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as possible
from these types of electronic devices.
•
•
Do not install this phone near a microwave oven or on the same electrical outlet. You may
experience decreased performance while the microwave oven is operating.
If you plug your phone in with a modem or a surge protector, plug the phone (or modem/
surge protector) into a different location. If this does not solve the problem, relocate your
phone or modem farther apart from one another, or use a different surge protector.
•
•
Relocate your phone to a higher location. The phone may have better reception in a high area.
If other phones in your home are having the same problem, contact your telephone service
provider (charges may apply).
I experience poor sound quality when using the speakerphone.
For increased sound quality while using the speakerphone, place the handset on a flat
surface with the dialing keys facing up.
•
I hear other calls when using the telephone.
•
Disconnect the telephone base from the telephone wall jack. Plug in a different telephone.
If you still hear other calls, the problem is probably in the wiring or telephone service.
Contact your telephone service provider.
I hear noise on the cordless handset and the keys do not work.
•
Make sure the telephone line cord is plugged in securely.
My caller ID features are not working properly.
•
Caller ID is a subscription service. You must subscribe to this service from your telephone
service provider for this feature to work on your telephone.
•
•
The caller may not be calling from an area which supports caller ID.
Both your and the caller’s telephone service providers must use equipment compatible with
the caller ID service.
•
•
The caller ID information shows after the first or second ring.
If you subscribe to high-speed Internet service (DSL - digital subscriber line) through
your telephone line, you must install a DSL filter between the telephone line cord and
the telephone wall jack. The filter prevents noise and caller ID problems caused by DSL
interference. Contact your DSL service provider for more information about DSL filters.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
The telephone does not receive caller ID while on a call.
•
Make sure you subscribe to caller ID with call waiting features provided by your telephone
service provider.
•
•
The caller may not be calling from an area which supports caller ID.
Both your and the caller’s telephone service providers must use equipment compatible with
caller ID service.
•
If you subscribe to high-speed Internet service (DSL - digital subscriber line) through
your telephone line, you must install a DSL filter between the telephone line cord and
the telephone wall jack. The filter prevents noise and caller ID problems caused by DSL
interference. Contact your DSL service provider for more information about DSL filters.
Out of range or no pwr at base shows on the handset screen.
•
•
The handset may be out of range. Move it closer to the telephone base.
Make sure the power cord is securely plugged into the telephone base. Use a working
electrical outlet not controlled by a wall switch.
•
Reset your telephone by unplugging the power adapter from the telephone base. Disconnect
the battery from the cordless handset. Wait for 15 seconds, then plug in the power adapter
and install the battery again. Place the handset in the telephone base and allow up to one
minute for the handset and telephone base to synchronize.
•
Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as possible
from these types of electronic devices.
and New voicemail show on the handset display and I don’t know why.
•
If
and New voicemail appear on the handset, your telephone has received a signal from
your telephone service provider that you have a voicemail message waiting for you to retrieve
from them. Contact your telephone service provider for more information on how to access
your voicemail.
I cannot retrieve voicemail messages.
•
If you subscribe to voicemail service from your telephone service provider (charges may
apply), contact your telephone service provider for more information on how to access
your voicemail.
I subscribe to a nontraditional telephone service that uses my computer to
establish connections, and my telephone doesn’t work.
•
•
•
•
Make sure your computer is powered on.
Make sure your Internet connection is working properly.
Make sure that the software is installed and running for your nontraditional telephone service.
Make sure to plug your USB telephone adapter into a dedicated USB port on your computer.
Do not plug into a multiple port USB hub (USB splitter) that is not powered.
•
•
In a few rare instances, the USB port on your computer may not have enough power. In
these instances, try using a USB hub with its own external power supply.
If you are using a firewall, it may prevent access to your nontraditional telephone service
provider. Contact your service provider for more information.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
I have accidentally set my LCD language to Spanish or French, and I don’t know
how to change it back to English.
•
•
While the phone is not in use, press MENU once then enter 364#.
While on a call, press MENU once then enter 364#. Then the call ends automatically.
Common cure for electronic equipment.
•
If the telephone is not responding normally, put the cordless handset in the telephone base.
If it does not respond, try the following (in the order listed):
1. Disconnect the power to the telephone base.
2. Disconnect the battery on the cordless handset.
3. Wait a few minutes before connecting power to the telephone base.
4. Install the battery again and place the cordless handset in the telephone base.
5. Wait for the cordless handset to synchronize with the telephone base. Allow up to one
minute for this to take place.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning.
4. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
6. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation.
To protect them from overheating, these openings must not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat
register. This product should not be placed in any area where proper ventilation is not provided.
7. This product should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supply in your home or office, consult your dealer or local
power company.
8. Do not allow anything to rest on the power cord. Do not install this product where the cord may be
walked on.
9. Never push objects of any kind into this product through the slots in the telephone base or handset
because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind
on the product.
10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service
facility. Opening or removing parts of the telephone base or handset other than specified access doors
may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock
when the product is subsequently used.
11. Do not overload wall outlets and extension cords.
12. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the
following conditions:
•
•
•
•
When the power supply cord or plug is damaged or frayed.
If liquid has been spilled onto the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operation instructions. Improper adjustment of other controls may
result in damage and often requires extensive work by an authorized technician to restore the
product to normal operation.
•
•
If the product has been dropped and the telephone base and/or handset has been damaged.
If the product exhibits a distinct change in performance.
13. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of
electric shock from lightning.
14. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances,
a spark may be created when the adapter is plugged into the power outlet, or when the handset is
replaced in its cradle. This is a common event associated with the closing of any electrical circuit.
The user should not plug the phone into a power outlet, and should not put a charged handset into
the cradle, if the phone is located in an environment containing concentrations of flammable or
flame-supporting gases, unless there is adequate ventilation. A spark in such an environment could
create a fire or explosion. Such environments might include: medical use of oxygen without adequate
ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.
15. Only put the handset of your telephone next to your ear when it is in normal talk mode.
16. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or
cabinet outlet.
SAVE THESE INSTRUCTIONS
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Important safety instructions
Battery
•
•
CAUTION: Use Only Supplied Battery.
Do not dispose of the battery in a fire. Check with local waste management codes for special disposal
instructions.
•
Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or injury to
the eyes or skin. The electrolyte may be toxic if swallowed.
•
•
Exercise care in handling batteries in order not to create a short circuit with conductive materials.
Charge the battery provided with or identified for use with this product only in accordance with the
instructions and limitations specified in this manual.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary
evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers.
Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
•
•
Should keep wireless telephones at least six inches from the pacemaker.
Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it
is turned ON.
•
Should use the wireless telephone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using
wireless telephones.
About cordless telephones
•
Privacy: The same features that make a cordless telephone convenient create some limitations.
Telephone calls are transmitted between the telephone base and the cordless handset by radio waves,
so there is a possibility that the cordless telephone conversations could be intercepted by radio receiving
equipment within range of the cordless handset. For this reason, you should not think of cordless
telephone conversations as being as private as those on corded telephones.
•
•
Electrical power: The telephone base of this cordless telephone must be connected to a working
electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made
from the cordless handset if the telephone base is unplugged, switched off or if the electrical power
is interrupted.
Potential TV interference: Some cordless telephones operate at frequencies that may cause
interference to televisions and VCRs. To minimize or prevent such interference, do not place the
telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced,
moving the cordless telephone farther away from the TV or VCR often reduces or eliminates
the interference.
•
•
Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with
conducting material such as rings, bracelets, and keys. The battery or conductor may overheat and
cause harm. Observe proper polarity between the battery and the battery charger.
Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not
burn or puncture the battery. Like other batteries of this type, if burned or punctured, they could release
caustic material which could cause injury.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Operating range
This cordless telephone operates with the maximum power allowed by the Federal Communications
Commission (FCC). Even so, this handset and telephone base can communicate over only a certain
distance - which can vary with the locations of the telephone base and handset, the weather, and the layout
of your home or office.
When the handset is out of range, the handset displays OUT OF RANGE OR NO PWR AT BASE.
If there is a call while the handset is out of range, it might not ring, or if it does ring, the call might not
connect well when you press /FLASH. Move closer to the telephone base, then press /FLASH to
answer the call.
If the handset moves out of range during a telephone conversation, there might be interference.
To improve reception, move closer to the telephone base.
ECO mode
This power conserving technology reduces power consumption for optimal battery performance, according
to the distance between the telephone base and the handset. When the telephone base communicates with
the handset, ECO mode will be activated automatically.
Maintenance
Taking care of your telephone
• Your telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
•
•
Place the handset down gently.
Save the original packing materials to protect your telephone if you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset in the rain, or handle it with wet
hands. Do not install the telephone base near a sink, bathtub or shower.
Electrical storms
•
•
Electrical storms can sometime cause power surge harmful to electronic equipment. For your own
safety, take caution when using electric appliances during storms.
Cleaning your telephone
•
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with
a soft cloth slightly dampened with water or mild soap.
•
Do not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you are wet or standing in water. If the
telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND
TELEPHONE LINE CORDS FROM THE WALL. Then pull the telephone out by the unplugged cords.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
The RBRC® seal
The RBRC® seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is voluntarily
participating in an industry program to collect and recycle these batteries at the end of their useful lives,
when taken out of service within the United States and Canada.
The RBRC® program provides a convenient alternative to placing used nickel-metal hydride batteries into
the trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers
participating in the RBRC® program or at authorized VTech product service centers. Please call
1 (800) 8 BATTERYTM for information on Ni-MH battery recycling and disposal bans/restrictions in your area.
VTech’s involvement in this program is part of its commitment to protecting our environment and conserving
natural resources.
RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device
under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended
to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Privacy of communications may not be
ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that
can be safely absorbed by a user or bystander according to the intended usage of the product. This product
has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear
of the user. The telephone base shall be installed and used such that parts of the user’s body other than the
hands are maintained at a distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the
Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment
contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be
provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must
comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to be connected to a compatible modular
jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line and an
RJ14 jack for two lines. See the installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your
telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th
and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but
not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your
telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment
connected to your telephone line, ensure the connection of this equipment does not disable your alarm
equipment. If you have questions about what will disable alarm equipment, consult your telephone service
provider or a qualified installer.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
FCC, ACTA and IC regulations
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been
corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized
agents. For repair procedures, follow the instructions outlined under the Limited warranty. If this equipment
is causing harm to the telephone network, the telephone service provider may temporarily discontinue your
telephone service. The telephone service provider is required to notify you before interrupting service.
If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity
to correct the problem and the telephone service provider is required to inform you of your right to file a
complaint with the FCC. Your telephone service provider may make changes in its facilities, equipment,
operation, or procedures that could affect the proper functioning of this product. The telephone service
provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers
(e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Privacy of communications may not be ensured when using this phone.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of
the maximum number of devices allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the
RENs of all the devices does not exceed five.
This product meets the applicable Industry Canada technical specifications.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
California Energy Commission battery charging testing
instructions
This telephone is set up to comply with the energy-conserving standards right out of the box. These
instructions are intended for California Energy Commission (CEC) compliance testing only. When the
CEC battery charging testing mode is activated, all telephone functions, except battery charging, will be
disabled.
To activate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet. Make sure all handsets are plugged
with charged batteries.
2. While you press and hold FIND HANDSET, plug the telephone base power adapter back to the
power outlet.
3. After about 20 seconds, when the IN USE light starts flashing, release FIND HANDSET and then
press it again within 2 seconds.
When the phone successfully enters the CEC battery charging testing mode, the IN USE light turns
off and all handsets display To register HS and See manual alternately.
When the phone fails to enter this mode, repeat Step 1 through Step 3 above.
Note: The telephone base will be powered up as normal if you fail to press FIND HANDSET within
2 seconds in Step 3.
To deactivate the CEC battery charging testing mode:
1. Unplug the telephone base adapter from the power outlet, then plug it back in. Then the telephone base
is powered up as normal.
2. Register your handsets back to the telephone base. See page 40 for handset registration instructions.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez toujours ces
mesures préventives de base lorsque vous utilisez votre téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.
3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de nettoyeurs liquides ni
en aérosol. N’utilisez qu’un chiffon doux et légèrement humecté.
4. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier de cuisine, d’un bac
de lavage ou d’une piscine, ou dans un sous-sol humide ou sous la douche.
5. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil pourrait tomber et
être sérieusement endommagé.
6. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière ou en dessous. Afin
d’empêcher la surchauffe, ces ouvertures ne doivent pas être obstruées en plaçant l’appareil sur un lit,
divan, tapis ou autre surface similaires. Ne placez pas cet appareil à proximité d’un élément de chauffage
ni d’une plinthe électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet fermé qui ne
possède pas d’aération adéquate.
7. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes de l’appareil.
Si vous ne connaissez pas le voltage de votre maison, consultez votre marchand ou votre fournisseur
d’électricité.
8. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit sécuritaire, là où
personne ne pourra trébucher sur la ligne d’alimentation ni le cordon téléphonique modulaire.
9. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient toucher à
des points de tension dangereux ou court-circuiter des pièces, ce qui constituerait un risque d’incendie
ou d’électrocution. N’échappez pas de liquides dans l’appareil.
10.Afin de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le plutôt à un
centre de service qualifié s’il doit être réparé. En enlevant le couvercle, vous vous exposez à des
tensions dangereuses ou autres dangers similaires. Un remontage inadéquat peut être à l’origine d’une
électrocution lors d’une utilisation ultérieure de l’appareil. Débranchez l’appareil avant de procéder au
nettoyage. Utilisez un chiffon humide et doux.
11.Ne surchargez pas les prises de courant et les rallonges.
12.Débranchez cet appareil de la prise de courant et communiquez avec le département de service à la
clientèle de VTech dans les cas suivants:
• Lorsque le cordon d’alimentation est endommagé ou écorché.
• Si du liquide a été échappé dans l’appareil.
• Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.
• Si le produit ne fonctionne pas normalement en respectant les instructions de fonctionnement. Réglez
uniquement les commandes indiquées dans le les instructions de fonctionnement. Les réglages
incorrects des autres commandes pourraient provoquer un dommage qui pourrait exiger un travail
exhaustif de la part d’un technicien autorisé afin de rétablir le fonctionnement normal de l’appareil.
• Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.
• Si le produit affiche une nette diminution de sa performance.
13.Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les éclairs peuvent être à l’origine
d’une électrocution.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
For C-UL compliance only
14.N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En certaines
circonstances, une flammèche pourrait être provoquée lorsque l’adaptateur est branché à une prise
de courant, ou lorsque le combiné est déposé sur le socle. Ceci est un événement commun associé à
la fermeture d’un circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à une prise de
courant, et ne devrait pas déposer le combiné chargé sur le socle, si le téléphone se trouve à proximité
d’un endroit comportant des concentrations de gaz inflammables, à moins que la ventilation soit
adéquate. Une flammèche dans un tel endroit pourrait provoquer un incendie ou une explosion. De tels
environnements peuvent comprendre: des endroits où l’on utilise de l’oxygène médical sans ventilation
adéquate; des gaz industriels (dissolvants de nettoyage, des vapeurs d’essence, etc.); une fuite de gaz
naturel, etc.
15. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de conversation.
16.Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au sol. Les broches ne
sont pas conçues pour maintenir l’adaptateur en place si celui-ci est barnché dans une prise au plafond ou
sous une table/ armoire.
CONSERVEZ CES INSTRUCTIONS
Pile
•
•
MISE EN GARDE : N’utilisez que la pile incluse.
Ne jetez pas la pile au feu. Vérifiez les instructions spécifiques de mise aux rebus auprès des autorités
locales.
•
•
•
N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et pourrait causer
des brûlures ou des blessures aux yeux ou à la peau. L’électrolyte est toxique si avalé.
Soyez prudents lorsque vous manipulez les piles afin d’éviter les courts-circuits provoqués par des
matériaux conducteurs. .
Rechargez la pile incluse ou identifiée pour fonctionner avec cet appareil, selon les instructions et limites
spécifiées dans ce guide d’utilisation.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené
une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs
cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des
États-Unis, la firme WTR recommande aux médecins :
Avis aux détenteurs de stimulateurs cardiaques
•
•
Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du stimulateur cardiaque.
Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une
poche de chemise, lorsque celui-ci est en marche.
•
Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans la direction opposée
au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs
cardiaques causés par les gens qui utilisent un téléphone sans fil à proximité de ceux-ci.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
For C-UL compliance only
À propos des téléphones sans fil
• Confidentialité : Les mêmes caractéristiques qui constituent des avantages pour les téléphones sans fil
affichent également des restrictions. Les appels téléphoniques sont transmis entre le combiné sans fil et le
socle par le biais d’ondes radio ; il y a donc la possibilité que vos conversations téléphoniques sans fil soient
interceptées par des équipements de réception radio se trouvant dans la portée du combiné sans fil. Pour
cette raison, vous ne devez pas percevoir les communications téléphoniques sans fil comme étant aussi
confidentielles que celles des téléphones à cordons.
• Alimentation électrique : Le socle de ce téléphone sans fil doit être branché à une prise électrique
fonctionnelle. La prise électrique ne doit pas être contrôlée par un interrupteur mural. Les appels ne pourront
pas être effectués du combiné sans fil si le socle est débranché ou mis hors tension ou si le courant est
coupé.
• Possibilité d’interférences aux téléviseurs : Certains téléphones sans fil fonctionnent sur des fréquences
pouvant causer des interférences aux téléviseurs et aux magnétoscopes. Pour réduire ou prévenir de telles
interférences, ne placez pas le socle du téléphone sans fil près ou sur un téléviseur ou magnétoscope. S’il
y a présence de parasites, il est conseillé d’éloigner le téléphone sans fil du téléviseur ou du magnétoscope
afin de réduire possiblement les interférences.
• Piles rechargeables : Manipulez les piles avec soin afin de ne pas les court-circuiter avec des bagues,
bracelets ou clés. Les piles ou le conducteur peut surchauffer et causer des blessures. Respectez la polarité
adéquate entre la pile et le chargeur.
• Les bloc-piles rechargeables à l’hydrure métallique de nickel : Jetez ces blocs-piles de manière
écologique et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les autres piles de ce type, elles
pourraient dégager une matière toxique qui peut causer des blessures corporelles si elles sont brûlées ou
percées.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or
“you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects
in material and workmanship, pursuant to the following terms and conditions, when installed and used
normally and in accordance with the Product operating instructions. This limited warranty extends only to the
Consumer for Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the
limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at
VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new
or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or
refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the
repaired or replacement Products to you in working condition. You should expect the repair or replacement
to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech
repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited
warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date
the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year
warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper
installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an
authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or
cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have
been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or
Canada, or used for commercial or institutional purposes (including but not limited to Products used for
rental purposes); or
7. Product returned without a valid proof of purchase (see item 2 on the next page); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems
outside the unit.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Limited warranty
How do you get warranty service?
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and
features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and
transportation and are responsible for delivery or handling charges incurred in the transport of the
Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty.
Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the
Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not
meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of
repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the
repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along
with a description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and
the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other
written or oral communications related to this Product. VTech provides no other warranties for this Product.
The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other
express warranties. No one is authorized to make modifications to this limited warranty and you should not
rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an
unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase.
Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential,
or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other
associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use
of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Technical specifications
Frequency control
Transmit frequency
Crystal controlled PLL synthesizer
Handset: 1921.536-1928.448MHz
Telephone base: 1921.536-1928.448MHz
Channels
5
Nominal effective
range
Maximum power allowed by FCC and IC. Actual operating range may vary
according to environmental conditions at the time of use.
Power requirements
Memory
Handset: 2.4V Ni-MH battery
Telephone base: 6V AC @ 300mA
Charger: 6V AC @ 300mA
Handset directory:
50 memory locations; up to 30 digits and 15 characters
Handset caller ID log:
50 memory locations; up to 24 digits and 15 characters
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
I
About caller ID 34
Indicators 44
Installation 2–3, 5–6
Intercom 25–26
About cordless telephones 54
Add a directory entry 28–29
Add a handset 40
Add a speed dial entry 32
Alphabetical search 30
Answer a call 18
J
Join a call 24
K
B
Key tone 16
Battery 52
Battery charging 4
Battery installation 3
L
Language 13
Layout 7–9
Listening volume 18
C
Caller ID 34–39
Call log display screen messages 39
Call transfer 22
Call waiting 19
Chain dialing 24
Charger installation 2
Charging 4
Check voicemail 21
Clear voicemail 15
Clock 17
M
Maintenance 53
Make a call 18
Menu 10
Missed call indicator 35
Multiple handset use 24
Mute 19
O
Operation 18–23
D
Date 17
P
Delete a directory entry 31
Delete a redial entry 20
Delete a speed dial entry 33
Dial a call ID log entry 36
Dial a directory entry 30
Display screen messages 42–43
Paging handset 20
Parts checklist 1
Precautions for users of implanted
cardiac pacemakers 51
Pulse dialing 17
Q
E
Quiet mode 11
Edit a directory entry 31
End a call 18
R
F
Redial 20
Register a handset 40
Replace a handset 41
Review the directory 30
Ringer 10
Find handset 20
Flash 19
H
Handset icons 44
Handset indicators 44
Handset layout 8–9
Handset lights 44
Handset ringer 10
S
Screen icons 44
Set date and time 17
Settings 10–17
Share an outside call 24
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Speed dial 32–33
Store a directory entry 28–29
Store a speed dial entry 32
T
Technical specifications 62
Telephone base indicators 44
Telephone base installation 2
Telephone base layout 7
Telephone base lights 44
Telephone base ringer 10
Temporary tone dialing 20
Time and date setting 17
Tone dialing 17
Troubleshooting 45–50
U
Using the menu 10
V
Voicemail 14, 15, 21
Volume 18
W
Wall mount installation 5, 6
Warranty 60–61
Website 22
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Designed to fit your home.
And your life.
VTech Communications, Inc.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2014 VTech Communications, Inc.
All right reserved. 05/14. CS6519-X_WEBCIB_V2.0
Document order number: 91-006067-020-100
Download from Www.Somanuals.com. All Manuals Search And Download.
|
