VTech Cordless Telephone 5808 User Manual

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed

to reduce the risk of fire, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol

cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, sink or swimming pool).

5. Do not place this product on an unstable surface such as a table, shelf or stand. The

product may fall, causing serious damage.

6. Slots and openings in the back or bottom of the base unit and handset are provided for

ventilation. To protect them from overheating, these openings must not be blocked by

placing the product on a soft surface such as a bed, sofa or rug. This product should

never be placed near or over a radiator or heat register. This product should not be placed

in any area where proper ventilation is not provided.

7. This product should be operated only from the type of power source indicated on the

marking label. If you are not sure of the type of power supply in your home, consult your

dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not install this product where the cord

may have anyone walking on it.

9. Never push objects of any kind into this product through slots in the base or handset as

they may touch dangerous voltage points or short out parts that could result in a risk of

fire or electric shock. Never spill liquid of any kind on the product.

10. To reduce the risk of electric shock, do not disassemble this product, but take it to an

authorized service facility. Opening or removing parts of the base or handset other than

specified access doors may expose you to dangerous voltages or other risks. Incorrect

reassembling can cause electric shock when the product is subsequently used.

11. Do not overload wall outlets and extension cords as this can result in the risk of fire or

electric shock.

12. Unplug this product from the wall outlet and refer servicing to an authorized service

facility under the following conditions:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled onto the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally by following the operating instructions. Adjust

only those controls that are covered by the operating instructions, as improper

adjustment of other controls may result in damage and often requires extensive work

by an authorized technician to restore the product to normal operation.

E. If the product has been dropped and the base and/or handset has been damaged.

F. If the product exhibits a distinct change in performance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Your phone is an advanced cordless telephone that operates in the 5.8GHz frequency range.

Your phone is capable of supporting up to a maximum of eight handsets. Using additional

handsets, up to four people can be conferenced on a call (three handsets and the base

speakerphone).

This manual is designed to familiarize you with your cordless telephone. We strongly recom-

mend you read the manual before using your phone.

To order additional system handsets (model number 5808), batteries or headsets, contact the

Supplier.

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts Check List

1. Base Unit

7. Belt Clip

2. Handset

8. User’s Manual

9. Audio Patch Cord

10. Battery

11. VTech Phonebook Manager CD

3. Base Power Adapter

4. Telephone Line Cord

5. Special Features Guide

6. Quick Start Guide

12. USB Cable

Base Unit

Belt Clip

Handset

Battery

Base Power Adapter

Quick Start Guide

(English and Spanish)

Special Features Guide

(English and Spanish)

Telephone Line Cord

VTech Phonebook

User's Manual

(English and Spanish)

Manager CD

USB Cable

Audio Patch Cord

Download from Www.Somanuals.com. All Manuals Search And Download.

The Handset Layout

1. Earpiece

7. LCD Display

2. USB Cable Jack

3. Headset Jack / Audio

Patch Cable Jack (2.5mm)

4. On/Flash Key

8. Menu/Select Key

9. Softkeys

10. NavKeys(Navigation Keys)

11. Volume Keys

5. Dialing Keys (0-9, *, #)

6. Speakerphone Key

12. Off/Clear Key

13. Microphone

Download from Www.Somanuals.com. All Manuals Search And Download.

The Base Unit Layout

1. Charging LED

2. LCD Display

3. Message LED

4. Speakerphone

5. Softkeys

8. Volume Key

9. Dialing Keys (0-9, , #)

10. Clear

11. Antenna

12. Microphone

6. Flash

13. Telephone Jack

14. DC Connector Jack

15. Spare Battery Compartment

7. Intercom

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup

Connecting Power to Base Unit

Plug the power adapter into an electrical outlet, and the connector into the bottom of the base

unit.

To outlet

Installation and Charge of Battery

Follow these steps:

1. Remove the battery cover and place

the battery in the compartment with

the metal contacts aligning, as shown

in the diagram.

2. Replace the cover by sliding it

upwards.

3. If the new battery is not already

charged, place the handset in its

base unit, and allow it to charge for a

minimum of 12 hours. After initial

charge, a maintenance charge of

eight hours should be sufficient.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup

Charging of the Handset Battery

The handset of your cordless telephone is powered by a rechargeable battery. It charges

automatically whenever the handset is in its base. Maximum talk time on fully charged

battery is seven hours, and maximum standby time is four days.

You should charge the battery for a minimum of 12 hours when you first receive your

phone.

12:00AM

You’ll know the battery need charging when:

•

The low battery message is displayed:

HANDSET1

The handset seems completely dead, the LCD is completely

dark and does not activate when you press the keys.

Low Battery

REDIAL

CALL LOG

IMPORTANT:

1. Do not dispose of batteries in a fire, they might explode.

2. Do not open or mutilate the batteries. Toxic substances may be released,

causing harm to eyes or skin.

3. Exercise care in handling batteries in order to prevent an accidental

short of the charge contacts, potentially causing the batteries to overheat.

4. Do not dispose of batteries into household garbage. They should be properly recycled.

5. If the phone will not be used for long periods of time, remove the battery to prevent

possible leakage.

Connecting to Phone Line

Plug one end of the telephone line cord into the jack on the

bottom of the base unit. Plug the other end of this cord into

the wall jack.

Checking for Dial Tone

After the battery is charged, press

/FLASH (on) on the handset. The Phone icon

will

appear on the handset display, and you will hear dial tone. If not, see In Case of Difficulty.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup

CAUTION: Use only the power supply provided with your telephone.

IMPORTANT! FOR MAXIMUM PERFORMANCE OF

YOUR CORDLESS TELEPHONE SYSTEM:

1. Choose a central location for your base unit.

2. Install your base unit and accessory handsets

away from electronic equipment, such as personal

computers, television sets and microwave

ovens.

3. In locations where there are multiple cordless

telephones, separate base units as much as

possible.

4. Install your telephone equipment away from heat

sources and sunlight.

5. Avoid excessive moisture, dust or extreme cold.

Download from Www.Somanuals.com. All Manuals Search And Download.

Power Guard/Spare Battery Charger Feature

Power Guard

Your phone uses the spare battery charger in the base unit to provide operational backup in

the event of a power failure. With a fully charged battery in the spare battery charger, you will

still be able to place and receive calls, for up to 2.5 hours.

The spare battery can also be used to replace drained handset battery ensuring uninterrupted

use. The spare battery is optional and purchased separately.

NOTE: When using your phone during power guard mode, audio quality may be compro-

mised due to reduced power availability.

Installation

1. Open the spare battery compartment by pressing on the cover and sliding in the direction

as indicated on the cover.

2. Place the battery in the charger with the metal contacts aligning, as shown in the diagram

below.

3. Replace the spare battery compartment cover. The spare battery charger takes 20

hours to fully charge drained battery.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Registration of Accessory Handset

Expand your 5858 system by adding accessory handsets. Bring telephone

access to rooms where a phone jack isn’t available!

Your 5858 phone system can operate up to eight handsets. To order additional handsets

(model 5808), contact the Supplier.

The original handset that is shipped with your 5858 system will be automatically

registered to the base. This handset is HANDSET 1.

As you register additional accessory handsets (model 5808) to the system, they will be

assigned extension numbers in the following order: HANDSET 2, HANDSET 3, etc.

Whenever a charged handset battery is installed, the handset will automatically begin Search-

ing for Base... (if previously registered), or it will prompt you to register the new handset.

The 5808 accessory handset consists of the following:

Battery

Charger

Special Features Guide

(English and Spanish)

Handset

Belt Clip

VTech Phonebook

Manager CD

Audio Patch Cable

User’s Manual

(English and Spanish)

USB Cable

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Registration of Accessory Handset

Setup of 5808 Accessory Handset

1. Plug the power adapter into an electrical

outlet.

2. Place the battery in the handset with

the metal contacts aligning, as shown

in the diagram to the left.

3. Replace the battery compartment

cover by sliding it upward.

4. Place the handset in the charger, and

allow it to charge for a minimum of 12

hours. After the initial charge, a

maintenance charge of eight hours

should be sufficient.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Registration of Accessory Handset

Registration

Your 5858 handset comes registered to the base unit. To register additional 5808 handsets

(purchased separately):

Registering the 5808 handset for the first time

After charging, the handset will display registration directions, which

are as follows:

•

On the base unit, press MENU, then select REGISTER

HANDSET.

12:00AM

BASE SETTINGS

10 NEW CALLS

When the base unit shows READY TO REGISTER NEW

HANDSET, press REGISTER on the handset.

READY TO

HANDSET

CANCEL

The handset displays Registration in Progress.

12:00AM

Registration

in Progress...

•

Within approximately 15 – 60 seconds the base and handset

will beep, and the newly registered handset will be assigned

the lowest extension number not previously assigned to

another system handset (1 – 8).

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset and Base Indicators

Handset Icons

Icon

Description

Line In Use Indicator

• On steady when an extension handset or parallel set is in use.

Hold Indicator

• Flashes when a call is on hold.

Mute Indicator

• Flashes when the handset microphone is muted.

Ringer Off Indicator

•

is displayed when the ringer is turned off.

Battery Indicator

• When the handset is removed from the charger, this lets you know the

level of charge in the battery, from FULL(

) to EMPTY (

• Cycles (low, medium, and full) when handset battery is charging.

• Flashes when a low battery condition is detected.

Message Waiting Indicator

• Flashes to indicate that you have new voicemail messages. (Service

must be subscribed to through your local telephone company.)

Handset LEDs

LED

Description

On when handset speakerphone is in use.

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset and Base Indicators

Base Unit Icons

Description

Icon

Ringer Off Indicator

is displayed when the base ringer is turned off.

Line In Use Indicator

• On steady when an extension handset or parallel set is in use.

Hold Indicator

• Flashes when a call is on hold.

Battery Indicator

• Cycles (low, medium, and full) when battery is charging in the

spare battery compartment.

• Flashes when the base is under power backup mode (No AC

power is detected).

Mute Indicator

• Flashes when the microphone is muted.

MUTE

Base LEDs

LED

Description

•

Flashes to indicate that you have new voicemail messages.

(Service must be subscribed to through your local telephone

company.)

Message

•

Flashes when a call is on hold.

Speakerphone

Charging

Lights when base speakerphone is in use.

•

On when the handset is in its base.

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset Menu

Handset Main Menu

Enter the handset main menu options by pressing MENU/SEL. Use the

to select from the seven menu items described below.

and

NavKeys

NavKeys (Navigation Keys)

Press the

and

NavKeys to maneuver through the various options in the handset

main menu. Press MENU/SEL to choose the displayed menu item.

Phonebook

Enter and retrieve up to 100 names and phone numbers, each can be assigned a distinctive

ring and image.

Call Log

Review caller ID data, select and dial from the caller ID data .

Intercom

Talk between handset(s) and base unit (when at least one accessory handset is regis-

tered to your base unit), or use to page the handset(s) or base.

Settings

Set the time, change the tone setting, adjust the phone settings, change the language of the

menu prompts or reset all to factory settings.

Sounds

Record custom sound clips, turn ringer and vibrate feature on or off, select main ringer tone.

Pictures

Choose from the many preset images or download new images into the handset to be used

as your idle screen (wallpaper) or assign an image to a specific phonebook directory.

Animations

Choose from many preset images to use as your idle (wallpaper) screen or assign as a

distinctive image to a specific phonebook directory.

Use the up and down NavKeys to maneuver to the desired menu option, then press MENU/

SEL to select.

Screen Saver

After 30 seconds of inactivity in idle mode, your handset will go into screen saver mode.

While in screen saver mode, your handset will display a digital clock. To illuminate the

screen and read the clock. simply press the volume buttons on the right edge of the

handset.

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset Menu

Phonebook

Enter the phonebook directly from idle mode by pressing the

Navkeys.

— OR —

Press MENU/SEL, then using the

and

NavKeys, scroll to phonebook, then press

MENU/SEL. If there are no entries, the screen will display Phonebook is empty. The

i 5858 handset can store up to 100 numbers with names in the phonebook directory, along

with a distinctive ring and image for each. Each memory location can hold up to 32 digits and

up to 16 characters, including spaces.

Each press of a key will cause characters to be displayed as follows:

Number Key

Characters (in order)

’

Space

Phone Book

Adding Phonebook Entries

Phone Book

is empty

•

From the handset idle (off) mode, press the

NavKey.

•

Press the NEW softkey.

NEW

FIND

NOTE: When the phonebook is full and NEW is pressed, Phonebook is full will display

and an error tone will sound.

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset Menu

•

You will then be prompted to Enter Name. Use the

digit keys to spell the name. If you make a mistake,

Phone Book

VTech|

press the

softkey. To add a space between

characters, press twice. When finished, press

the SET softkey.

SET

NOTE: Press to advance the cursor. Press again to

add a space.

Phone Book

•

Enter the number you want to store in the phonebook.

Press and hold the # key to insert a pause. If you

make

mistake, press the right softkey

.When finished, press SET. The screen will

display:

SET

Phone Book

NOTE: If you do not wish to assign a distinctive ring

tone or image to this phonebook entry, press

SAVE now.

SAVE

•

If you wish to be alerted to calls from this phone

number, you can assign a unique ring tone to this

phonebook entry. Press the up or down NavKey to

scroll to Ringer : < Default >.

Phone Book

Press the left or right NavKey to sample the ringer

options. Press

tone.

to return to the default ring

- OR -

SAVE

Press MENU/SEL then press the up or down

NavKey to sample the options. Once you have

selected a ringer, press SET.

•

Once you have selected a ringer, press the down

NavKey to move on and select a a distinct image or

animation for this entry or press SAVE to confirm

your selections. You must subscribe to caller ID

service for the distinctive ring function to work.

NOTE: There are eight traditional ring tones and 17

musical ringers. For Recordable Ringer,

see page 25.

•

If you wish to be visually alerted to calls from this

number by changing to a distinctive image or ani-

mation, press the

NavKey to scroll to

Picture: < (none) >.

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset Menu

•

Press the or NavKey to sample the picture and

animation options. If you make a mistake, press

Phone Book

to delete.

— OR —

•

Press MENU/SEL then press the

sample the picture and image options.

Once you have selected an image or animation, press

SET. You must subscribe to caller ID service for the

distinctive image or animation feature to work.

NavKey to

SAVE

NOTE: There are 29 preset pictures and animations to

choose from. For Picture Download information, see page

26.

Phone Book

•

Once you’ve selected a picture or an animation, press

SAVE.

Entry has been

saved

Your phonebook entry has been saved and the

screen will display:

NEW

FIND

Searching for and Dialing Phonebook Entries

•

With the handset in idle (off) mode, press the

NavKey to enter the phonebook.

•

Continue pressing the

NavKeys to scroll

through the contents in alphabetical order.

Phone Book

— OR —

Use the number keys to enter the first characters of the

name. The closest match alphabetically will be displayed.

NEW

FIND

— OR —

Phone Book

Search for

Press the FIND softkey, enter the first few characters

of the name and then press SET to search. If you make a

mistake, press the

softkey. The closest match

alphabetically will be displayed.

SET

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset Menu

•

Once you find the entry you want, simply press

/FLASH (on) or SPEAKERPHONE to dial the

number.

Phone Book

Editing Phonebook Entries

•

Following the first two steps in Searching for and

Dialing Phonebook Entries, locate the entry you

want to edit.

NEW

FIND

Phone Book 3

•

Press the MENU/SEL. The screen will display:

Press the EDIT or MENU/SEL softkey.

EDIT

DELETE

Phone Book

•

Press

edit then enter the corrections as needed. Press the

softkey to delete.

NavKeys to the option you want to

SAVE

When finished, press the SAVE softkey. The

screen will display the edited entry.

Deleting Phonebook Entries

•

Following the first two steps in Searching for and

Dialing Phonebook Entries, locate the entry

you want to delete.

Phone Book 3

•

Press MENU/SEL. The screen will display:

EDIT

DELETE

Press DELETE softkey. The entry will be deleted.

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset Menu

Call log

To access the call log, press the CALL LOG softkey.

- OR -

Press MENU/SEL, then the

call log menu. Press MENU/SEL.

NavKeys to scroll to

Call Log NEW 1

Then use the

CID records in the call log.

and

NavKeys to scroll and view the

1-800-595-9511

Nov 12 11:00AM

SAVE

DELETE

This feature allows you to scroll through the 100 current

caller ID and call waiting records received. With a CID

record displayed, press SAVE to store it in the

phonebook (see page 17), or press DELETE to remove

the entry from the log.

Dial Options

595-9511

You can also dial a CID record while reviewing. With

the desired CID displayed, press # or MENU/SEL. The

possible options to choose from will be either 7, 10, or

11 digits. For example, if the original number in caller

ID memory was 800-595-9511, then the display options

will be:

800-595-9511

1-800-595-9511

DIAL

Press the

and

NavKeys to make the selection,

/FLASH (on) or to dial

then press left softkey,

the number.

NOTE: Due to regional incompatibilities, CID information

may not be available for every call you receive. In addition,

the calling party may intentionally block their name and/or

phone number from being sent.

Intercom

Global Page

BASE

From Handset to Handset (or Base):

•

With the Intercom icon highlighted, press MENU/

SEL.

•

Press the

Press MENU/SEL.

The ringing handset (or base) can answer by pressing

and

NavKey to the desired handset.

/FLASH (on) , or any of the number keys (or

HANDSET1

the intercom button on the base)

To end an intercom call, press

•

/CLEAR (off)

on any handset or place the handset to base unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset Menu

NOTE: To access this feature, you must have at least one

additional handset. To order accessory handsets, please

refer to page 11.

Intercom

Global Page

Base

HANDSET1

Global Page from Handset:

•

With the Intercom icon highlighted, press MENU/SEL.

Press the up or down NavKey to highlight Global Page.

Press MENU/SEL.

Performing

Global Page

•

Any registered handset and base can answer the global

page, thus entering intercom mode.

To end the intercom call, press

any handset or base.

/CLEAR (off) on

Settings

Enter the settings menu by pressing MENU/SEL, then the

and

NavKeys. When Settings

are displayed, press MENU/SEL. Use the up and down NavKeys to choose from the following:

Clock Setting

This option allows you to change the time that will display on the idle screen. If you subscribe

to caller ID, the time will be set automatically when the first caller ID record is received.

NOTE: If you choose to set the time manually, use the number keys and the

and

NavKeys.

Tone Settings

This option allows you to turn the following options on or off: keypad tone, low battery tone,

and out of range tone.

Phone Settings

Choose this option to change the contrast of your handset screen, edit handset name, show

handset name, select dial type (choose from tone or pulse), display product ID.

NOTE: Your phone is preset for tone dialing.

Language

This option allows you to change the screen prompts to English, Spanish or French.

Reset Settings

Choose this option to reset the following settings: Clear Msg Indication, Phonebook, Call Log,

Redial List, Wallpaper, Registration, Factory Settings.

NOTE: The Factory Settings option will reset the settings listed above back to the factory

defaults. The screen will display Restore Factory Settings Are you sure? Press the YES

or NO softkey to make your selection.

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset Menu

Sounds

Play Sound Clips

This option allows you to access all preset melodies and the melodies you have recorded

using the Recordable Ringer option (see page 25 for details.)

Record Sound Clip

Choose this selection to record your own ring tones. See recordable ringer on page 25 for

complete instructions.

Ringer Melody

This option allows you to assign various ring tones for incoming calls. You can choose from

eight preset traditional ringers or 17 preset musical ringers or the ring tones you have

recorded.

Ringer Volume

Adjust the ringer volume to a comfortable setting or turn the ringer off.

NOTE: When the phone is ringing, press SILENCE softkey or CLEAR key to temporarily

mute the ringer

Ringer Vibrate

Turn the vibrating ringer on or off.

Use the

and

NavKeys to maneuver through the menu options. Press the SET softkey

to confirm your selection.

Pictures

Your handset is preset with 23 pictures you can use as the background for your idle screen

(wallpaper) or assign a specific image to a phonebook directory. You can also download

your own pictures (see Picture Download on page 26).

Set a Wallpaper image

To set a wallpaper image, select the icon Pictures in the main menu. Then use the up and

down Navkeys to view the available images. Once you have selected the image, press the

SET softkey to set the image as your wallpaper. You will receive a message on the screen

confirming Wallpaper Set and an audio confirmation.

Set an Animation image

To set an animation as your wallpaper, select Animation in the main menu. Then use the

and

Navkeys to view the available images. Once you have selected an animation,

press the SET softkey to set the image as your wallpaper. You will receive a message on

the screen confirming Wallpaper Set and an audio confirmation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset Menu

Redial

12:00AM

•

Press the REDIAL softkey to display the last 20 telephone

numbers dialed from the handset. The number on the top

line represents the last number dialed.

HANDSET1

REDIAL

CALL LOG

Redial

•

Use the

and

NavKey to scroll to the desired number.

595-9511

1-595-9511

800-595-9511

1-800-595-9511

SAVE

DELETE

To dial, press

/FLASH (on) or

Redial

595-9511

1-595-9511

800-595-9511

1-800-595-9511

Saving Redial Number in Phone Book Memory

•

Press REDIAL, then scroll to the desired number.

•

Press SAVE.

SAVE

DELETE

Phone Book

VTech|

•

You will be asked to ENTER NAME. Use the keypad to

enter the desired name (see Phonebook for more

information).

•

Press SET. The name and number has been stored in

Phonebook memory.

SET

Redial

595-9511

Deleting Numbers in Redial Memory

1-595-9511

800-595-9511

1-800-595-9511

•

Press REDIAL, then scroll to the desired number.

•

Press DELETE.

SAVE

DELETE

Download from Www.Somanuals.com. All Manuals Search And Download.

Recordable Ringer

Record a Ringer

You can easily record a unique ringer to be used as either your default ringer or for a

distinctive ringer assigned to a specific phonebook directory. You can record with either the

provided audio patch cord (not the USB cord), or with the handset microphone.

NOTE: The space allotted for recordable ringers and picture download are dynamic. this

means you can delete pictures to make more room for custom ring tones, if you wish.

Cued-up music typically produces the best sounding recorded ringer. It is recommended to

begin recording your ringer at the beginning of a song, rather than a portion from the middle

to produce an audibly pleasing custom ringer.

NOTE: Your handset is preset with 17 musical ringer options (i.e. harmony, reflection,

harmonic, swing, etc.) for you to use as your default ringer or a distinctive ringer. Four of

the ringers are protected, you cannot replace them. You can replace the other ringers

with your own recordings. You will find 14 additional sound clips excluding those preset in

the handset on the accompanying CD-ROM.

•

You can use the audio patch cord by inserting the 3.5mm plug (the larger end) into the

headset jack of your PC or audio source. Then insert the 2.5mm plug (the smaller end)

into the headset jack on the side of the handset.

You can listen to the playing music through your handset speaker after connecting the

audio patch cord and selecting the Using Audio Cable menu option. Adjust the record-

ing volume at the audio source. To begin recording, press RECORD.

If you want to use the handset microphone to record ringers, select the Using Micro-

phone menu option. After the beep, and with the handset microphone facing the audio

source, start recording.

•

Select the Sounds icon

in the main menu.

Select the Record Sound Clips option, the handset will show Using Microphone or

Using Audio Cable. The handset will record up to 15 seconds.

NOTE: If the memory is full, the handset will prompt Sound Clip memory full.

•

Press the STOP softkey stop the recording.

After recording, you may PLAY or SAVE the melody. If you choose SAVE, you will be

prompted to Enter Clip Name. Enter a name (up to ten characters) for the recording. If

you make a mistake, press the

softkey to backspace. Press SAVE to

confirm. Sound Clip saved will display. The melody will be stored in the Play Sound

Clips section. You can listen to all of your recorded music clips in this location. If you

want, when in Play Sound Clips, you can press DELETE then YES to erase.

NOTE: When you want to use the handset microphone to record ringers, do not insert the

audio patch cord into the headset jack.

Download from Www.Somanuals.com. All Manuals Search And Download.

Picture Download

Getting Started

The VTech Phonebook Manager allows you to download pictures and edit your handset

phonebook from the convenience of your PC. It also allows you to import/export contacts

from/to comma separated text files. This great feature allows you to get contacts from your

existing PC applications such as Microsoft Outlook or Palm programs.

One-time Software Installation

•

Insert the enclosed VTech Phonebook Manager CD into your personal computer.

An installation window will open on your monitor giving you three options:

1. Install/Uninstall the phonebook manager software.

2. Browse the installation CD.

3. Visit VTech on the web.

•

To install the software, click on the Install/Uninstall the VTech Phonebook Manager

icon

and follow the download instructions.

After the installation is complete, you will find a VTech phonebook manager icon

your PC desktop.

Graphics Tab Functions

The VTech phonebook manager allows you to open graphic files on your PC and transfer

them to your phone. Once the graphics are transferred, they can be used for your wallpaper

image or to assign to a particular phonebook entry, quickly alerting you to your caller’s

identification.

With the phonebook manager you can also modify the graphic prior to sending it to the

handset. Common graphic editing functions such as zoom, rotate, brightness/contrast ad-

justment and red/green/color balance adjustments can all be done from the VTech phonebook

manager.

Open a Graphic File

•

Open the phonebook manager by double-clicking on the desktop icon:

•

Click on the Graphics tab.

Click on the OPEN IMAGE button.

A window will open to allow you to browse for the graphic file on your computer.

Find the folder containing your graphic file and double-click to open it.

Picture Download

Once you’ve opened a graphic file, it can be transferred from your PC to your handset. There

are many images loaded onto the phonebook manager software you can download into your

handset, or you can transfer your own pictures onto the handset. The phonebook manager

supports the following graphic formats: GIF, JPEG, BMP, TIFF and PNG.

NOTE: The space allotted for recordable ringers and picture downloads in your handset are

dynamic. This means you can delete ring tones to make more room for image downloads, if

you wish.

To transfer images from the software to the handset:

•

Connect one end of the enclosed USB cable to the handset and the other end to your PC.

If you have the phonebook manager program open, you should see the status in the

bottom right corner update that the PC has detected the phone. You are now ready to

transfer a graphic to the phone.

•

Following the steps in Open a Graphic File.

Once you have opened the desired image, click on the Transfer to Handset button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Picture Download/Phonebook Tab Functions

•

The graphic transfer will now begin and complete within approximately four seconds.

Once the graphic transfer is complete, the image is saved in the phone, you do not need

to do anything else to save the image.

Graphic Editing

The VTech phonebook manager allows you to perform basic graphic editing functions such

as zoom, rotate, adjust brightness/contrast and adjust the color balance. As you use these

tools to edit your pictures, you can see them update on the preview panel on the left side of

the phonebook manager application.

NOTE: None of the graphic editing functions will alter the actual graphic file – they will only

modify how the graphic will look once it has been downloaded to the handset.

While in graphic edit mode, you will notice a red preview box over the center of main graphic

panel. This preview box contains the image shown in the preview panel on the left side of the

application. You can move the preview box by:

1. Move the mouse pointer so it’s inside the red preview box.

2. Press and hold the left mouse button.

3. Use the mouse to move the red preview box to hover over a new location on the graphic.

4. Once the preview box is over the area of the graphic you want to download onto your

handset, release the mouse button.

Phonebook Tab Functions

The VTech phonebook manager can be used to create, modify and backup phonebook files

from your handset. The phonebook manager has many useful functions:

•

Export existing contacts from any contact manager (such as Microsoft Outlook, Palm,

etc.) to a comma separated text file. Import those contacts into the phonebook manager

and transfer the entire phonebook to your handset.

•

Transfer a phonebook from your handset to your PC and save it to disk. Connect a

different handset and transfer the phonebook from your PC to the new handset. This

allows you to easily store a copy of a phonebook on your PC and transfer it to several

different handsets.

•

Use the phonebook manager to backup your handset phonebook onto your PC. If for any

reason you need to restore the phonebook on your handset, you have a copy safely

stored on your PC.

Use the phonebook manager to create a phonebook offline on your PC. When you have

finished editing it, connect your handset and transfer it from the PC to your handset.

NOTE: The phonebook manager application does not perform any synchronization of the

phonebook between the PC and the handset. When the Transfer to Handset button is

pressed, the entire phonebook is transferred to the handset replacing the existing phonebook

on the handset.

Creating an Empty Phonebook

To create an empty phonebook to input data:

•

Double-click on the VTech phonebook manager icon on your PC.

Click on the Phonebook tab.

•

Select the CREATE PHONEBOOK

button.

Using the phonebook manager application, make any changes required to the phonebook.

You can add entries or import contacts from other PC applications such as Microsoft

Outlook or Palm.

Download from Www.Somanuals.com. All Manuals Search And Download.

Phonebook Tab Functions

•

Once you have completed editing the phonebook, you must either save the data to your

PC’s hard drive or transfer it to your handset:

Select the SAVE PHONEBOOK

button to save the data to your PC’s hard

drive.

-OR-

•

Click on Transfer

NOTE: This operation will replace the phonebook on your handset with the new one you have

currently transferred from the phonebook manager.

Edit a Phonebook

You can either open an existing phonebook stored in your PC’s hard drive by pressing the

OPEN PHONEBOOK

button using the phonebook manager software, or by

transferring the phonebook from your handset by transferring it to the phonebook manager

software using the supplied USB cable. To accomplish this:

•

Connect your handset to your PC using the USB cable.

Start the phonebook manager application on your PC.

Verify the connection by insuring the green icon on the status bar. (If it is not, re-connect

the handset to the PC with the USB cable.)

•

Press the Phonebook tab.

Press the Transfer

button.

Using the phonebook manager software, edit the phonebook entries as you wish. At this

time you can also add new entries or import contacts from other programs such as

Microsoft Outlook or Palm, etc.

•

When you are finished editing the phonebook, save it to your PC’s hard drive by pressing

the SAVE PHONEBOOK

button. To transfer the newly edited phonebook to

your handset, use the transfer phonebook

button.

Import Contacts Into Phonebook Manager From Other PC Applications

Use this feature to import contacts from a comma separated text file into the VTech phonebook

manager software. The contacts will be merged into the currently loaded phonebook.

1. Create a comma separated text file containing the contacts you want to import into your

handset. This is accomplished by using the export function from your other contact

management application (such as Microsoft Outlook, Outlook Express or Palm applica-

tions). The export function in these programs is normally located under the file menu. Be

sure to specify the export file as a text file or comma separated file (CSV). An example of

exporting contacts from Microsoft Outlook is as follows:

a. Start Microsoft Outlook on your PC.

b. Select import/export from the file menu.

c. Select export to file and press next.

d. Select a file type of comma separated values (in Windows).

e. Select the folder containing the contacts you want to export.

f. Once you’ve selected a contact folder, press next.

g. Enter a file name to save your contacts to. This will be the file you select to import into

the phonebook manager program. Be sure to make note of where on your PC you save

the file for later reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

Phonebook Tab Functions

2. Start the VTech phonebook manager program on your PC. Load the newly created

phonebook into the phonebook manager software using these steps:

•

Press the Transfer

button.

•

Press the CREATE PHONEBOOK

button. This will create an empty phonebook.

button to load the previously saved phonebook

Press the OPEN PHONEBOOK

from your PC’s hard drive.

NOTE: For first time users, try the import operation on an empty phonebook until you have

mastered the process.

•

Press the Import/Export

button.

Select Import Contacts and press the next button.

Use the browse button to locate the comma separated text file you saved in step one.

Press next.

•

The next screen displays how the fields from the comma separated text file will be

mapped to the handset phonebook entries. There are two fields in the VTech phonebook;

name and number. However, most PC contact managers separate names into the first

and last name fields. To allow import of this type of file, the mapping dialog allows you to

instruct how the name fields from your import file will be placed in the VTech phonebook

name field. For example, the following mappings will import the fields first name and last

name into the VTech name field. The home phone field will be imported into the VTech

phone number field:

If the mapping displayed is not what is desired, select one of the rows and press the

Change Map button to correct it. You can only use each of the three fields (VTech name

first, VTech name last and VTech phone number) once. If you want to change one that

has already been mapped, you must first select that row and use the Change Map button

to remove the association.

When you are done editing the mapping, press the Finish button. The contacts will now

be imported and merged into the currently loaded phonebook.

•

Exporting Contacts to a Comma Separated Text File

This feature allows you to export some or all of your VTech phonebook entries into a comma

separated text file. This comma separated text file can then be imported into common contact

manager software such as Microsoft Outlook or Palm applications.

•

Load a phonebook into the phonebook manager.

If you wish to only export some of your contacts, select the desired contacts in the list of

contacts loaded. You can use your mouse to select to a single row. If you want to select

multiple rows, hold down the CTRL key while using your mouse to click on the rows to be

selected.

•

Press the Import/Export

Select Export Contacts and press the next button.

Select whether you want to Export All Contacts or Selected Contacts.

Enter the name of the file to export the contacts to. You can use the browse button to

locate the folder and enter a file name.

button.

•

Press the Finish button to complete the export operation.

Deleting Phonebook Records From the Currently Loaded Phonebook

•

Start the phonebook manager software on your PC.

Press the Phonebook tab.

Load a phonebook into the phonebook manager.

Select the rows of the phonebook records that are to be deleted. You can use your

mouse to select a single row. If you want to select multiple rows, hold down the CTRL key

while using your mouse to click on the rows to be selected.

•

Press the Delete Selected Contacts

Save the file to disk and/or transfer it to the handset.

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Menu Soft Functions

Your phone has an advanced design that uses a

menu structure and softkeys to access many of

the features.

12:00AM

Example of the idle mode display:

10 NEW CALLS

Redial

Your base remembers the last 10 numbers dialed

from it. Press REDIAL. The number on the top

line represents the last number that was dialed.

•

Use the scroll keys to highlight the desired

number.

To dial, press SPEAKERPHONE.

Erasing Numbers in Redial Memory

• Press REDIAL, then scroll to the desired number.

•

Press SELECT, then DELETE.

DELETE

SAVE

Saving Redial Numbers in Phonebook

Memory

•

Press REDIAL, then scroll to the desired

number.

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Menu Soft Functions

•

Press SELECT, then SAVE.

DELETE

SAVE

•

You will be asked to ENTER NAME. Use the

keypad to enter the desired name (see To Store

a Number/Name on page 37).

Press SAVE. The name and number has been

stored in phonebook memory.

Base Unit Menu

With the base unit in the idle (off) mode, press the MENU key to access the CALL LOG,

BASE SETTINGS and REGISTER HANDSET options.

Press the CLEAR key to go backward through the menu. Press and hold CLEAR to immediately

return to the idle screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Menu Soft Functions

Calls Log

Caller ID - call waiting ID

Your phone is capable of displaying the name and/or number of the party calling before you

answer the phone (caller ID). It is also capable of displaying caller ID information in conjunction

with a call waiting alert signal (call waiting caller ID). With call waiting caller ID, the caller ID

data is displayed so you can decide whether to answer the incoming call, or continue with

your current conversation.

NOTES ABOUT CALLER ID & CALL WAITING CALLER ID

These are subscription services, provided by most regional telephone service providers.

You must subscribe to these services to get the benefits of these features. If you do not

subscribe to caller ID services, you can still use your phone and the other features it

offers. Due to regional incompatibilities, caller ID information may not be available for every

call you receive. In addition, the calling party may intentionally block their name and/or

phone number from being sent.

Reviewing caller ID from the base

As new caller ID/call waiting ID records are received,

12:00AM

your base display will alert you to the new caller ID

records, for example:

10 NEW CALLS

The number of new calls displayed on each system handset and base may not be the same.

If, for example, you answer a call on a handset, the handset will not count the caller ID

information for that call as new. However, the base displays will consider it a new call, and add

it to the NEW CALLS total.

After you review a new caller ID record, the NEW CALLS status will be turned off.

From the idle (off) mode, press MENU, highlight the

CALL LOG option, then press SELECT. The caller

ID information of the most recently received call will

be displayed. For example:

To scroll to other records, use the and

softkeys.

SELECT

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Menu Soft Functions

Dialing from Caller ID

To dial the number displayed, simply press the

key.

You can also use the dialing option as follows:

Dialing Option: Press SELECT. Use the

and

Navkeys to scroll to DIAL OPTION, then

press SELECT. Up to three possible dialing

options of the number stored in caller ID

memory will display. If a number is provided

in the caller ID data, the possible options to

choose from will be either 7, 10, or 11 digits.

For example, if the original number in caller

ID memory was 800-595-9511, then the

display options will be:

SELECT

Use the

and

softkeys to make a

selection, then press DIAL or

to dial

the number.

Dialing Tip: With a caller ID record displayed, press

# repeatedly to cycle through the three

dialing options. When the correct dialing

option is displayed, press DIAL or

dial.

Save CID Records to Phonebook Memory

Press SELECT, then SAVE TO PH. BOOK. Only caller ID records with telephone numbers

can be saved into the phonebook. If you need to

modify the number after saving, see To Edit a

Number.

Deleting CID Records

To delete the displayed caller ID record, press

SELECT, then DELETE CALL LOG. You will then

have the option of deleting the current CID record

(press THIS) or all stored CID records (press ALL).

If you press ALL, the screen will ask ARE YOU

SURE? Press YES to confirm the deletion of all CID

records. Or press NO to return to the CID record

previously displayed.

NOTE: You do not have to manually delete caller ID records. Your phone saves up to 50

most current CID records in base unit. As new records come in, the oldest records are

automatically deleted to make room.

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Menu Soft Functions

Base Settings

To access base settings, with the base in the idle (off) mode, press MENU, scroll down to

BASE SETTINGS, then press SELECT. You can now access the following setting options:

CLOCK SETTING

KEYPAD TONE

CLEAR MSG WAIT

PRODUCT ID

RINGER VOLUME

CONTRAST

FACTORY SETTINGS

RINGER MELODY

DIAL TYPE

DELETE HANDSETS

Press CLEAR at any time to back out of the base settings mode.

Clock Setting

If you subscribe to caller ID, the clock will automatically be set when the first call is received.

If you don’t have caller ID or wish to set the clock manually:

•

Press MENU, then scroll to BASE SETTINGS.

CLOCK SETTINGS will be highlighted, press SELECT.

Press the CHANGE softkey to change the first digit of the hour, press NEXT. (Follow this

procedure to change the remaining digits of the time and select AM or PM.)

When finished, press SET, you’ll hear a confirmation tone.

•

Ringer Volume

To adjust the base unit ringer volume:

•

Press MENU. Scroll down to BASE

SETTINGS, then press SELECT. Use the up

and down softkeys to RINGER VOLUME,

press SELECT. You will see a graph on the

base display indicating the current volume

setting.

SET

•

Press the

softkey to lower the ringer

volume. At the lowest setting (graph is

completely clear), the base will not ring when

a call comes in.

•

Press the

softkey to raise the volume.

At the loudest setting, the graph is completely

shaded in.

Press SET to confirm your setting.

NOTE: When the phone is ringing, press QUIET

softkey or CLEAR key to temporarily mute the

ringer.

Ringer Melody

There are six base ringer melody choices. To

change the melody:

RINGER MELODY 4

•

Press MENU. Scroll down to BASE

SETTINGS, press SELECT. Scroll down to

RINGER MELODY.

SET

•

Press SELECT. Use either scroll key to

sample the melodies.

Press SET to confirm your selection.

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Menu Soft Functions

Keypad Tone (preset to ON)

Keypad tones are the beeps you hear each time

you press a key on the base unit.

To turn this feature ON or OFF:

SET

•

Press MENU. Scroll down to BASE

SETTINGS, press SELECT. Scroll down to

KEYPAD TONE.

•

Press SELECT. Choose ON or OFF.

Press SET to confirm.

Contrast

You can adjust the contrast of the base unit's LCD

screen to suit your eyes:

•

Press MENU. Scroll down to BASE

SETTINGS, press SELECT. Scroll down to

CONTRAST.

•

Press SELECT. Use the

keys to lower and raise the screen’s contrast.

and

scroll

SET

Press SET to confirm your selection.

Dial Type

To change the dialing mode:

•

Press MENU. Scroll down to BASE SETTINGS,

press SELECT. Scroll down to DIAL TYPE.

•

Press SELECT. Choose TONE or PULSE.

Press SET to confirm.

SET

Clear Message Waiting Indicator

To manually clear the message waiting

indicator:

•

Press MENU, then scroll to BASE

SETTINGS.

•

Press SELECT, Scroll down to Clear Msg

Wait.

Press YES or NO.

CLEAR

MESSAGE WAITING

INDICATOR

•

ARE YOU SURE?

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Menu Soft Functions

Factory Settings

If you wish to reset your phone to the settings programmed at the factory:

•

Press MENU, then scroll to BASE SETTINGS.

Press SELECT, then scroll to FACTORY SETTINGS.

Press SELECT, the screen will display RESTORE FACTORY SETTINGS ARE YOU

SURE?

•

Press YES or NO.

Delete Handsets

To deregister all handsets from the base:

•

Press MENU, then scroll to BASE SETTINGS.

Press SELECT, then scroll to DELETE HANDSETS.

Press SELECT. The screen will display DELETE REGISTRATION FOR ALL

HANDSETS ARE YOU SURE? Press YES to deregister all handsets.

NOTE: If you choose this option, you will need to re-register the handset(s) to the base

before you can use your phone. See Installation and Registration of Accessory Handset

on page 11-13 for instructions.

Phonebook Memory

Your base can store up to 50 numbers with names in memory. Each memory location can

hold up to 32 digits for the number and 16 characters for the name.

When prompted to Enter Name, use the digit keys to spell the name. Each press of a

particular key causes characters to be displayed in the following order:

Number Key

Characters (in order)

’

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Menu Soft Functions

NOTE: Each system handset and the base unit can independently store names and numbers

in memory. Adding, editing or deleting items stored in one unit does not affect the phonebook

in any other system handset or the base.

To Store a Number/Name:

•

Starting from the idle screen, enter

the number you want to store in

memory.

12:00AM

10 NEW CALLS

•

Be sure to include long distance

codes and pauses (using the

PAUSE softkey).

•

Press the SAVE softkey.

You will then be prompted to Enter

Name. Use the digit keys to spell

the name. If you make a mistake,

ENTER NAME

press the

softkey. To enter

a space press SPACE. When

finished, press SAVE.

•

If there is space available in

memory, the entry will be saved

and the base will return to pre-dial

mode.

If the memory is full, the base will

display PHONEBOOK IS FULL

and exit to pre-dial mode without

saving the entry.

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Menu Soft Functions

To Search For and Dial a Number/ Name:

•

Starting from the idle screen, press the PH BOOK

softkey to review memory contents.

PHONE BOOK

•

Use the

softkeys to scroll

through the memory contents in alphabetical

order.

-OR-

Press the FIND softkey, enter the first few

chararcters of the name and then press FIND to

search. If you make a mistake, press the

softkey. The closest match alphabetically will be

displayed.

•

Once you find the entry you want, simply press

SPEAKERPHONE to dial the number.

To Delete a Number/Name:

•

Following the first two steps in To Search For

and Dial a Number/Name, locate the entry you

want to delete.

•

Press the EDIT softkey. The screen will display:

•

Press the DELETE softkey. The screen will

display:

•

To delete this record, press THIS. The record

will be deleted, and the next entry in the

phonebook will be displayed.

•

To delete all records in your phonebook memory,

press ALL. The display will ask ARE YOU SURE?

To confirm the deletion of all records, press YES.

To exit without deleting press NO.

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Menu Soft Functions

To Edit a Number

•

Following the first two steps in To Search For

and Dial a Number/Name, locate the entry you

want to edit.

•

Press the EDIT softkey twice. The handset will

display:

•

Press NAME or NUMBER, depending on which

you want to edit.

Using the

softkey move the cursor to

the character you want to edit then enter the

corrections as needed. Press MORE to access

SPACE and BACK functions. Pressing MORE

again will return the previous screen. When finished

press the SAVE softkey. To exit without saving

press CLEAR.

When finished, the screen will display the edited

entry:

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset and Base Operation

Making Calls

From the handset:

•

Press

/FLASH (on) or

to use the handset

speakerphone feature.

Dial the phone number.

-OR-

Dial the phone number first, then press

/FLASH

(on) or

Press

•

/CLEAR (off) to end your call or place

the handset in its base to end your call.

From the base unit:

•

Press

Dial the phone number.

-OR-

•

Dial the phone number first, then press

Press

again to end your call.

NOTE: In pre-dial mode, press PAUSE softkey to

add pause. Press CLEAR to make correction. Or

press and hold the CLEAR to delete all the input.

Answering Calls

From the handset:

•

Press

/FLASH (on) or

or any dialing keys.

Press

/CLEAR (off) to end your call.

-OR-

Place the handset in its base to end your call.

From the base unit:

•

Press

again to end your call.

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset and Base Operation

Handset Volume

The volume control is on the right edge of the

handset. During a call, press the + or keys to

adjust the listening volume to a comfortable level.

You can adjust the volume for the headset and

speakerphone this way also.

Base Speakerphone Volume

During a call simply press the volume (or

speakerphone volume). keys to adjust the

speakerphone volume.

Sound Select (Handset Only)

During a call, you can adjust the quality of the

sound to best suit your hearing. Pressing and

NavKeys repeatedly will cycle you through

four different frequency responses:

Sound Select

Bass

BASS - Low frequency sounds

enhanced.

MID - Mid-range sounds

enhanced. (This is the recom-

mended setting for hearing aid

users).

Sound Select

Mid

TREBLE - High frequency

sounds enhanced.

Sound Select

Treble

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset and Base Operation

NATURAL - No frequency

enhancement. (Your handset is

preset to this selection).

Sound Select

Natural

NOTE: The sound select feature cannot be used when

in speakerphone or headset mode.

Mute Function

HOLD

MUTE

During an active call pressing either the MUTE softkey on the

handset or base (when in speakerphone mode), will disable

the microphone. Press UNMUTE to return to normal two-

way conversation.

Hold Function

From the handset:

•

Press the HOLD softkey to place a call on hold. To return

to the call, press the /FLASH (on) key.

HOLD

MUTE

NOTE: The handset will display Call on Hold when a call is

placed on hold. A will flash to remind you a call is on

hold. If a call remains on hold for one minute, your i 5858

handset will ring to remind you the call is being held. The

phone will display Call on Hold Ringback! You have 30

seconds to return to the call before it is dropped.

From the base:

•

During an active call, press the HOLD softkey to place a

call on hold. The SPEAKERPHONE LED will flash to indicate

a call is on hold.

800-595-9511

•

To return to the call, press SPEAKERPHONE.

NOTE: If a call remains on hold for one minute, your 5858

base will ring to remind you the call is being held. The phone

will display CALL ON HOLD RING BACK! You have 30

seconds to return to the call before it is dropped.

Flash Function

You can use your phone with services such as call waiting.

Simply press the

/FLASH (on) key on the handset or the

FLASH key on the base (when in speakerphone mode) to

flash the line.

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset and Base Operation

Intercom

From Base to ALL Handsets:

•

At the base press INTERCOM, scroll to GLOBAL PAGE,

then press SELECT.

•

Each handset will display Global Call from BASE.

Any handset can then answer the page, and enter

intercom mode by pressing

/FLASH (on) or any dialing keys.

/CLEAR (off) on the handset or INTERCOM on the

•

To end an intercom call, press

base.

From Base to a Specific Handset:

•

Press INTERCOM, then scroll to the handset you want to call (e.g. HANDSET 2). Press

SELECT.

Handset 2 can then answer the intercom call pressing

keys.

/FLASH (on) or any dialing

To end an intercom call press

base.

/CLEAR (off) on the handset or INTERCOM on the

For handset intercom operation, please refer to Handset Menu - Intercom (see page 21).

Handset Speakerphone Operation

Your handset has a built-in handsfree speakerphone. This feature allows you to stand the

handset upright on a table or desktop and have handsfree conversations. For more

information, refer to Making Calls in Handset and Base Operation (see page 40).

Base Speakerphone Operation

The base of your phone is equipped with a speakerphone. This is a very useful feature for

handsfree conversations or conference calls at the base unit. For more information, refer to

Making Calls in Handset and Base Operation (see page 40).

Line in Use Indication

12:00AM

On the Handset:

VTECH

When the telephone line is currently being used

at the handset, base or another phone in your

Line in Use

home, the screen will display:

REDIAL

CALL LOG

On the Base:

Similar to the handset, when a system handset

or another phone in your home is in use,

your base screen will display LINE IN USE.

LINE

IN USE

Download from Www.Somanuals.com. All Manuals Search And Download.

Handset and Base Operation

Conference Calling

Your phone is capable of supporting conference calls with up to three registered handsets

and the base unit. To enter a conference call, simply press

/FLASH (on) or

) on the

handset or base. The phone icon

display.

will be displayed in the upper middle of the handset

Transferring Calls

You can transfer calls from the base to handset, handset to handset, or handset to base.

Announced Transfer

Perform an announced transfer (call and advise another extension) of an active call:

From the Handset:

•

Press HOLD to place your call on hold.

Press MENU\SEL, then use NavKey scroll to Intercom, press MENU\SEL again.

Press the or NavKey to the desired destination.

Press the MENU\SEL again.

When the ringing handset or base answers, announce that there’s an active call on hold.

Press

/CLEAR (off) on the handset or INTERCOM on the base.

•

/FLASH (on) on the destination handset or SPEAKERPHONE on the

destination base to pick up the call on hold.

From the Base:

•

Press HOLD to place your call on hold.

Press INTERCOM.

Scroll to the desired destination, then press SELECT.

When the ringing handset answers, announce that there’s an active call on hold.

Press

call.

/CLEAR (off) on the handset or INTERCOM on the base to exit the internal

•

Press

/FLASH (on) on the destination handset to pick up the call on hold.

Download from Www.Somanuals.com. All Manuals Search And Download.

Headset Operation

Your handset is equipped with a 2.5mm headset jack for use with an optional accessory

headset for handsfree operation. If you choose to use the headset option, you must obtain

a compatible accessory headset. To purchase a headset, contact the Supplier.

Once you have a compatible 2.5mm headset, locate the headset jack on the handset.

Connect the plug on the headset cord to the jack (under a small rubber flap) on the cordless

handset. The plug should fit securely. Do not force the connection.

NOTE:

Whenever a compatible headset is connected to

the cordless handset, the microphone on the

handset will be muted. This is done to limit the effect

of background noise.

Belt Clip

Your phone is also equipped with a detachable belt

clip. Align the pins on the inside edge of the clip

with the notches on the sides of the handset. The

belt clip should snap securely into place. Do not

force the connection.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

Taking care of your telephone

Your cordless telephone contains sophisticated electronic parts, so it must be treated

with care.

Avoid rough treatment

Place the handset down gently. Save the original packing materials to protect your

telephone if you ever need to ship it.

Avoid water

Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the

rain, or handle it with wet hands. Do not install your base unit near a sink, bathtub, or

shower.

Electrical storms

Electrical storms can sometimes cause power surges harmful to electronic equipment.

For your own safety, use caution when using electric appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that should retain its luster for many years.

Clean it only with a soft cloth slightly dampened with water or a mild soap. Do not use

excess water or cleaning solvents of any kind.

Remember that electrical appliances can cause serious injury if used when you are

wet or standing in water. If your base unit should fall into water, DO NOT RETRIEVE

IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM

THE WALL. Then pull the unit out by the unplugged cords.

Download from Www.Somanuals.com. All Manuals Search And Download.

In Case Of Difficulty

If you have difficulty operating your phone, the suggestions below should solve the problem.

If you still have difficulty after trying these suggestions, call the Supplier.

The phone doesn't work at all

•

Make sure the power cord is plugged in.

•

Make sure the telephone line cord is plugged firmly into the base unit and the telephone

wall jack.

•

Make sure the batteries are properly charged. If you get a LOW BATTERY message or

indication, the batteries need charging.

No dial tone

•

First try all the suggestions above.

•

If you still don't hear a dial tone, disconnect the base unit from the telephone jack and

connect a different phone. If there is no dial tone on that phone either, the problem is in

your wiring or local service. Contact your local telephone company.

You get noise, static, or a weak signal even when you're near the base unit

•

Household appliances plugged into the same circuit as the base unit can sometimes

cause interference. Try moving the appliance or the base unit to another outlet.

You get noise, static, or a weak signal when you're away from the base unit

•

You may be out of range. Either move closer to the base, or relocate the base unit.

•

The layout of your home may be limiting the range. Try moving the base unit to another

position.

The handset does not ring when you receive a call

•

Make sure you have the ringer activated. Refer to the section on Sounds - Ringer

Volume in this user’s manual.

•

Make sure the telephone line cord is plugged firmly into the base unit and the telephone

jack. Make sure the power cord is plugged in.

•

You may be too far from the base unit.

You may have too many extension phones on your telephone line to allow all of them to

ring. Try unplugging some of the other phones.

Your handset vibrates or shakes when a call comes in

•

It is likely that your vibrating handset ringer option has been set to ON. If you’d like

to turn it off, see the section on Sounds - Ringer Vibrate in this user’s manual.

You hear other calls while using your phone

•

Disconnect your base unit from the telephone jack, and plug in a regular telephone. If you

still hear other calls, the problem is probably in your wiring or local service. Call your local

telephone company.

Download from Www.Somanuals.com. All Manuals Search And Download.

In Case Of Difficulty

You hear noise in the handset, and none of the keys or buttons work

•

Make sure the power cord is plugged in.

Common cure for electronic equipment

If the unit does not seem to be responding normally, then try putting the handset in the

charger. If it does not seem to respond, do the following (in the order listed):

1. Disconnect the power to the base.

2. Disconnect the handset batteries, and spare batteries, and spare battery cells, if applicable.

3. Wait a few minutes.

4. Connect power to the base.

5. Re-install the batteries.

6. Wait for the handset to re-establish its link with the base. To be safe, allow up to

one minute for this to take place.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warranty Statement

The Supplier warrants, to the original purchaser only, the material and workmanship of

this product for ONE YEAR from the date of purchase. We will repair or replace, at our

option, this product without charge should it fail due to a defect in material or workmanship

within that time period.

This warranty does not apply to loss or damage that is the result of accident, misuse or

negligence. All other warranties, expressed, implied or statutory, including warranties of

fitness for a particular purpose, are limited to the time period listed and are otherwise excluded

from this warranty if unauthorized repairs are attempted. Additionally, the Supplier shall not

be liable for any incidental or consequential damage or commercial loss, nor for any other

loss or damages.

The Supplier assumes no responsibility for products sent without prior return authorization.

Download from Www.Somanuals.com. All Manuals Search And Download.

FCC, ACTA and IC Regulations

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class

B digital device under Part 15 of the Federal Communications Commission (FCC) rules.

These requirements are intended to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this equipment not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency

energy that can be safely absorbed by a user or bystander according to the intended

usage of the product. This product has been tested and found to comply with the FCC

criteria. The handset may be safely held against the ear of the user. The base unit shall

be installed and used such that parts of the user’s body other than the hands are maintained

at a distance of approximately 20 cm (8 inches) or more. If you choose to use a clipping

device, please make sure to only use the supplied belt clip.

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements

adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the

back or bottom of this equipment contains, among other things, a product identifier in the

format US:AAAEQ##TXXXX. This identifier must be provided to your local telephone

company upon request.

The plug and jack used to connect this equipment to premises wiring and the telephone

network must comply with applicable Part 68 rules and technical requirements adopted

by ACTA. A compliant telephone cord and modular plug is provided with this product. It

is designed to be connected to a compatible modular jack that is also compliant. An RJ11

jack should normally be used for connecting to a single line and an RJ14 jack for two

lines. See Installation Instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine how many devices you may

connect to your telephone line and still have them ring when you are called. The REN

for this product is encoded as the 6th and 7th characters following the US: in the product

identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs

should be five (5.0) or less. For more information, please contact your local telephone

company.

This equipment may not be used with Party Lines. If you have specially wired alarm dialing

equipment connected to your telephone line, ensure the connection of this equipment does

not disable your alarm equipment. If you have questions about what will disable alarm

Download from Www.Somanuals.com. All Manuals Search And Download.

FCC, ACTA and IC Regulations

equipment, consult your telephone company or a qualified installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until the

problem has been corrected. Repairs to this telephone equipment can only be made by

the manufacturer or its authorized agents. For repair procedures, follow the instructions

outlined under the Limited Warranty.

If this equipment is causing harm to the telephone network, the telephone company may

temporarily discontinue your telephone service. The telephone company is required to notify

you before interrupting service. If advance notice is not practical, you will be notified as

soon as possible. You will be given the opportunity to correct the problem and the telephone

company is required to inform you of your right to file a complaint with the FCC. Your

telephone company may make changes in its facilities, equipment, operation, or procedures

that could affect the proper functioning of this product. The telephone company is required

to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is hearing aid compatible.

If this product has memory dialing locations, you may choose to store emergency telephone

numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency

numbers, please:

* Remain on the line and briefly explain the reason for the call before hanging up.

* Perform such activities in off-peak hours, such as early morning or late evening.

Industry Canada

This equipment complies with regulations RSS210 and CS-03 of Industry Canada. Operation

is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause

undesired operation of the device.

The term ‘’IC: ‘’ before the certification/registration number only signifies that the Industry

Canada technical specifications were met.

The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is

an indication of the maximum number of devices allowed to be connected to a telephone

interface. The termination on an interface may consist of any combination of devices subject

only to the requirement that the sum of the RENs of all the devices does not exceed five.

Download from Www.Somanuals.com. All Manuals Search And Download.

Technical Specifications

FREQUENCY CONTROL

Crystal controlled

WEIGHT

Handset:

145 grams

(excluding Battery)

463 grams

PLL synthesizer

Base:

TRANSMIT FREQUENCY

POWER REQUIREMENTS

Base:

5725-5850 MHz

Handset:

3 cell AAA 3.6V 800mAh

Handset: 5725-5850 MHz

NiMH Battery

Base:

7 VDC @ 1100mA

RECEIVE FREQUENCY

MEMORY

Handset:

Base:

5725-5850 MHz

Handset: 5725-5850 MHz

Phonebook: 100 Memory locations; up to 32

digits, 16 characters per location

CHANNELS

95 Channels

Caller ID:

100 Memory locations

NOMINAL EFFECTIVE RANGE

Maximum power allowed by FCC and IC.

Actual operating range may vary

according to environmental conditions at

the time of use.

Base:

Phonebook: 50 Memory locations; up

to 32 digits, 16 characters per location

Caller ID:

50 Memory locations

SIZE

Handset: 190mm x 42mm x 31mm

SPECIFICATIONS ARE TYPICAL AND

MAY CHANGE WITHOUT NOTICE.

Base:

250mm x 90mm x 84mm

(including antenna)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table Of Contents

Important Safety Instructions ............................................................................................ 1

Introduction........................................................................................................................... 3

Parts Check List .................................................................................................................... 4

The Handset Layout............................................................................................................. 5

The Base Unit Layout .......................................................................................................... 6

Getting Started ..................................................................................................................... 7

Setup ...................................................................................................................................... 7

Connecting Power to Base Unit.............................................................................................. 7

Installation and Charge of Battery.......................................................................................... 7

Charging of the Handset Battery ............................................................................................. 8

Connecting to Phone Line ....................................................................................................... 8

Checking for Dial Tone ........................................................................................................... 8

Power Guard...................................................................................... ................................. 10

Installation and Registration of Accessory Handset............................................................ 11

Basic Operations ................................................................................................................ 14

Handset and Base Indicators ........................................................................................... 14

Handset Icons ....................................................................................................................... 14

Handset LEDs ....................................................................................................................... 14

Base Unit Icons ..................................................................................................................... 15

Base LEDs ............................................................................................................................ 15

Handset Menu ..................................................................................................................... 16

Handset Main Menu...........................................................................................................16

NavKeys (Navigation Keys) ................................................................................................. 16

Menu Shortcuts ..................................................................................................................... 16

Phonebook ............................................................................................................................ 17

Adding Phonebook Entries ................................................................................................... 17

Searching for and Dialing Phonebook Entries........................................................... ......... 19

Editing Phonebook Entries.................................................................................................. 20

Deleting Phonebook Entries ................................................................................................. 20

Call Log ....................................................................................................................... ...........21

Intercom ................................................................................................................................ 21

Settings ................................................................................................................... ...............22

Sounds....................................................................................................................................23

Pictures ................................................................................................................................. 23

Set a Wallpaper image .......................................................................................................... 23

Set an Animation image.............................................................................................23

Redial........................................................................................................................................24

Saving Redial Number in Phone Book Memory................................................................24

Deleting Redial Number in Phone Book Memory...............................................................24

Recordable Ringer.............................................................................................................. 25

Record a Ringer .................................................................................................................... 25

Picture Download ............................................................................................................... 26

Phonebook Tab Functions..........................................................................................27

Creating an Empty Phonebook........................................................................................27

Edit a Phonebook..................................................................................................................28

Import Contacts Into Phonebook Manager From

Other Contact Manager PC Applications........................................................28

Exporting Contacts to a Comma Separated Text File............................................29

Deleting Phonebook Records From the Currently Loaded Phonebook......................29

Base Menu Soft Functions ................................................................................ ...............30

Redial ..................................................................................................................................... 30

Erasing Numbers in Redial Memory........................................................................... 30

Saving Redial Numbers in Phonebook Memory .................................................................. 30

Download from Www.Somanuals.com. All Manuals Search And Download.

Table Of Contents

Base Unit Menu ..................................................................................................................... 31

Calls log ................................................................................................................................. 32

Caller ID - Call Waiting ID ..................................................................................................... 32

Reviewing Caller ID from the Base ...................................................................................... 32

Dialing from Caller ID ............................................................................................................ 33

Save CID Records to Phonebook Memory ......................................................................... 33

Deleting CID Records ........................................................................................................... 33

Base Settings............................................................................................................34

Clock Setting..........................................................................................................................34

Ringer Volume ....................................................................................................................... 34

Ringer Melody ....................................................................................................................... 34

Keypad Tone ......................................................................................................................... 35

Contrast ................................................................................................................................. 35

Dial Type ............................................................................................................................... 35

Clear Message Waiting Indicator.......................................................................................35

Factory Settings...................................................................................................................36

Delete Handsets....................................................................................................................36

Phonebook Memory .............................................................................................................. 36

To Store a Number/Name .................................................................................................... 37

To Search For and Dial a Number/Name ....................................................................... 38

To Delete a Number/Name ................................................................................................... 38

To Edit a Number .................................................................................................................. 39

Advanced Operations ........................................................................................................ 40

Handset and Base Operation ........................................................................................... 40

Making Calls .......................................................................................................................... 40

Answering Calls .................................................................................................................... 40

Handset Volume .................................................................................................................... 41

Base Speakerphone Volume ................................................................................................... 41

Sound Select (handset only) ................................................................................................ 41

Mute Function........................................................................................................................ 42

Hold Function ........................................................................................................................ 42

Flash Function ...................................................................................................................... 42

Intercom ................................................................................................................................ 43

Handset Speakerphone Operation ..................................................................................... 43

Base Speakerphone Operation ........................................................................................... 43

Line in Use Indication ........................................................................................................... 43

Conference Calling ............................................................................................................... 44

Transferring Calls ................................................................................................................. 44

Announced Transfer.........................................................................................................44

Additional Information ...................................................................................................... 45

Headset Operation ............................................................................................................. 45

Belt Clip .................................................................................................................................. 45

Maintenance ........................................................................................................................ 46

In Case of Difficulty............................................................................................................ 47

Warranty Statement............................................................................................................ 49

FCC, ACTA and IC Regulations ....................................................................................... 50

Technical Specifications ................................................................................................... 52

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

AddingPhonebookEntries..........................17

AdditionalInformation..................................45

AdvancedOperations..................................40

Announced Transfer.................................44

Answering Calls........................................40

Base LEDs.................................................15

Base Menu Soft Functions..........................30

BaseSettings...............................................34

Base Speakerphone Operation...................43

BaseSpeakerphoneVolume........................41

Base Unit Icons.........................................15

Base Unit Menu..........................................31

BasicOperations.........................................14

Belt Clip......................................................45

CallLog.........................................................21

Caller ID - Call Waiting ID.........................32

Callslog.......................................................32

Charging of the Handset Battery.................8

Checking for Dial Tone...............................8

Clear Message Waiting Indicator................35

Clock Setting...............................................34

Conference Calling.....................................44

Connecting Power to Base Unit.................7

Connecting to Phone Line.........................8

Contrast......................................................35

Creating an Empty Phonebook................27

Delete Handsets........................................36

Deleting CID Records...............................33

Deleting Phonebook Entries......................20

Deleting Phonebook Records From

ImportContacts/PhonebookManager........28

Important Safety Instructions......................1

In Case of Difficulty....................................47

Installation and Charge of Battery.................7

Installation and Registration of

Accessory Handset.............................11

Intercom.....................................................43

Intercom........................................................21

Introduction.....................................................3

Keypad Tone..............................................35

Line in Use Indication...............................43

Maintenance...............................................46

Making Calls..............................................40

Menu Shortcuts.........................................16

Mute Function...........................................42

NavKeys (Navigation Keys)...................16

Parts Check List...........................................4

Phonebook Memory...................................36

Phonebook Tab Functions.......................27

Phonebook...................................................17

PictureDownload........................................26

Pictures.......................................................23

Power Guard..............................................10

Record a Ringer.........................................25

RecordableRinger......................................25

Redial.........................................................30

Redial................................................................24

Reviewing Caller ID from the Base..........32

Ringer Melody............................................34

RingerVolume.............................................34

Save CID Records to

Phonebook Memory.........................33

Saving Redial Number in Phone

Book Memory......................................24

Saving Redial Numbers in

Phonebook Memory............................30

Searching for and Dialing

Phonebook Entries..............................19

Set a Wallpaper image...............................23

Set an Animation image...........................23

Settings.........................................................22

Setup...............................................................7

Sound Select (handset only)...................41

Sounds.................................................................23

TechnicalSpecifications.............................52

The Base Unit Layout...................................6

The Handset Layout..................................5

To Delete a Number/Name......................38

To Edit a Number.....................................39

To Search For and Dial a

the Currently Loaded Phonebook......29

Deleting Redial Number in Phone

Book Memory........................................24

DialType......................................................35

Dialing from Caller ID..................................33

Edit a Phonebook......................................28

Editing Phonebook Entries.......................20

Erasing Numbers in Redial Memory...........30

Exporting Contacts to a Comma

SeparatedText File................................29

FactorySettings...........................................36

FCC, ACTA and IC Regulations..............50

FlashFunction.............................................42

Getting Started............................................7

Handset and Base Indicators.....................14

Handset and Base Operation....................40

Handset Icons.............................................14

Handset LEDs...........................................14

Handset Main Menu..................................16

HandsetMenu..............................................16

Handset Speakerphone Operation...........43

HandsetVolume...........................................41

HeadsetOperation.......................................45

HoldFunction...............................................42

Number/Name.....................................38

To Store a Number/Name...........................37

TransferringCalls........................................44

WarrantyStatement....................................49

Download from Www.Somanuals.com. All Manuals Search And Download.

91-000XXX-010-000

ISSUE 0

Printed in China

Download from Www.Somanuals.com. All Manuals Search And Download.

Tektronix Network Card 80A03 User Manual
Topcom Network Router ATA 1110 User Manual
Topfield DVR TF 600 PVRt User Manual
Transcend Information Computer Drive TS1GJFT3 User Manual
Ultra Products Computer Drive ULT31830 User Manual
Underwater Kinetics Home Safety Product 4AA Mini Q40 User Manual
Uniden Digital Camera UDC 7M User Manual
Vivitar Camcorder X014 User Manual
Vizio Flat Panel Television E390I B1 User Manual
Weed Eater Blower 530164008 User Manual