VIPowER Network Card VP 8220 User Manual

SmartDup  
MODEL VP-8220  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SmartDup VP-8220 Operation Manu  
SmartDup VP-8220 Package Including:  
1. Duplicator Converter.  
2. CD-ROM Box (VP-6020) x 2  
3. AC/DC Power Adaptor (Universal Type +90 ~ +250VAC)  
Features:  
1. One to one Stand-Alone IDE CD Duplicator.  
2. Auto duplication & Easy operation without any push bottom.  
3. Fastest CD Duplicator up to 24x speed (ViPowER is the only factory that  
manufactures it today!)  
4. Auto Detects CD-R or CD-RW media's acceptable maximum writing speed and  
minimum writing time.  
5. Upgrade through Internet, or upgrade via CD-ROM.  
6. High Performance with Low cost & easy installation. No additional H/W or S/W  
required.  
7. External Power supply.  
8. Supports Buffer Under Run.  
9. Capable of connecting to your Desktop/ Notebook via Fire Wire/ USB/ PCMCIA/  
Card Bus cable. (See option Desktop Interface)  
10. Support Formats: Audio CD (CD-DA), CD-ROM, CD-XA (Photo & Video CD),  
CD-Digital, CD-Bridge, CD-Extra, Video CD & CD-Text.  
11. Automatically detects/ Erases/ Re-writes/ Copies.  
12. Compatible with most well known CD-RW & CD-ROM Devices.  
13. User friendly with LED display function.  
14. Buzzer to alert user.  
Install Steps:  
1. Install CDR-W Writer & CD-ROM Driver in each CD-ROM box. Must put rubber  
stand on each CD-ROM box.  
2. CD-ROM Driver on top & CDR or CDR-W Writer on the bottom.  
3. Plug in Duplicator Converter in both CD-ROM box connectors.  
4. Plug in Power Cable in Duplicator Converter.  
5. Plug in Power Cord to AC Power source (+90 ~ +250VAC).  
6. LED Display on top of Duplicator Converter.  
7. Dip Switch on Top of Right hand side. To adjust duplicator function.  
8. Rock Switch on Right hand side, power switch. Normally in ON position  
Function Setting  
4: Test & Copy 5: Test Only 6: Copy Only 7: Auto Mode  
(Erase & Copy)  
High Speed  
(Maximum)  
3: Erase Only 2: 1x Copy  
(Minimum)  
1: Upgrade 0: Reserved  
Firmware  
Low Speed  
(4x)  
SmartDup VP-8220 Operation Manu  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
H1 (Upgrade firm-ware): DIP SW 3 4 at ON position, 1 2 at OFF position---  
If you adjust DIP SW to L1, all operation step same as above, the Recording  
Speed will drop to 4x only.  
1 1. Turn Rock Switch to position (CD Duplicator). LED will show version number.  
Power-On: display firmware version number. (Buzzer 0.5s X1)  
ex:  
1-2. Than LED display showing: from 00,11, 22, 33, ......88, 99  
1-3. Duplicator will chk itself & get ready.  
Self-Test: Only one segment is running and display "rd" (ready)  
1-4. Please insert your new Firm-Ware CD title into your CD-ROM Drives,  
operation step as below:  
1 4 2. Switch your power switch to (PC interface)  
1-4-3. Please check Optional Step (page 10)  
1-4-4. Burning new Firm-Ware into your CD-R or CDR-W media.  
1-5. LED Display showing final counts down. Than LED showing H1 or L1.  
Count Down: After drives & discs ready in current mode, wait for  
5 seconds. (Buzzer 0.2s X1)  
ex:  
1-6. SmartDup will upgrade automatically.  
1-7. After Upgrade success, Buzzer will Beep & eject Firm-Ware Title. LED  
showing 00.  
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)  
1-8. Showing new firmware version.  
1-8-1. If fail, LED will showing: Er & eject CD-R Media, Buzzer will Beep also.  
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)  
2
SmartDup VP-8220 Operation Manu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
H2(1xCopy) DIP SW 2 4 at ON position, 1 3 at OFF position---------------  
L2(1xCopy) DIP SW 2 at ON position, 1 3 4 at OFF position----------------  
1xCopy Speed (H2 or L2) or CD-RW writer minimum writing speed.  
2-1. Turn Rock Switch to position (CD Duplicator). LED will show version  
number.  
Power-On: display firmware version number. (Buzzer 0.5s X1)  
ex:  
2-2. Than LED display showing: from 00,11, 22, 33, ......88, 99  
2-3. Duplicator will chk itself & get ready.  
Self-Test: Only one segment is running and display "rd" (ready)  
2-4. SmartDup ready, please insert your CD title into your CD-ROM Drive &  
Blank CD-R or CD-RW Media in CD-RW Writer.  
2-5. LED Display showing final counts down, than LED showing H2 or L2.  
Count Down: After drives & discs ready in current mode, wait for  
5 seconds. (Buzzer 0.2s X1)  
ex:  
or  
2-6. LED Display showing CD-R or CD-RW Media writing speed or depend on  
CD-RW writer minimum writing speed.  
CD-R Maximum Writing Speed:  
2-7. LED Display showing CD-R or CD-RW Media minimum writing time  
remaining.  
Remain minutes: During Test or Copy mode. Flash every second  
ex:  
or  
2-8. After Upgrade success, Buzzer will Beep & eject CD-R media. LED  
showing 00.  
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)  
2-8-1. If fail, LED will showing: Er & eject CD-R Media, Buzzer will Beep also.  
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)  
SmartDup VP-8220 Operation Manu  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
H3 (Erase Only): DIP SW 2 3 4 at ON position, DIP SW 1 at OFF position--  
L3 (Erase Only): DIP SW 2 3 at ON position, DIP SW 1 4 at OFF position---  
This function for RW Media with Data inside, operation steps same as H3,  
Erase speed drop to 4x only.  
3-1. Turn Rock Switch to position (CD Duplicator). LED will show version  
number.  
Power-On: display firmware version number. (Buzzer 0.5s X1)  
ex:  
3-2. Than LED display showing: from 00,11, 22, 33, ......88, 99  
3-3. Duplicator will chk itself & get ready.  
Self-Test: Only one segment is running and display "rd" (ready)  
3-4. SmartDup ready, please insert your CD title into your CD-RW Media in  
CD-RW Writer.  
Count Down: After drives & discs ready in current mode, wait for  
5 seconds. (Buzzer 0.2s X1)  
ex:  
or  
3-5. LED Display showing final counts down, than LED showing H3 or L3.  
3-6. Start Erasing.  
Erasing:  
3-7. After Erased success, Buzzer will Beep & eject CD-RW media. LED  
showing 00.  
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)  
3-7-1. If fail, LED will showing: Er & eject CD-R Media, Buzzer will Beep also.  
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)  
4
SmartDup VP-8220 Operation Manu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
H4(Test & Copy Mode) DIP SW 1 4 at ON position, 2 3 at OFF position-----  
L4(Test & Copy Mode) DIP SW 1 at ON position, 2 3 4 at OFF position-----  
If you adjust DIP SW to L4, all operation steps same as H4, the Recording  
Speed will drop to 4x only.  
Please make sure CD-R or CD-RW media is blank.  
4-1.Turn Rock Switch to position (CD Duplicator). LED will show version  
number.  
Power-On: display firmware version number. (Buzzer 0.5s X1)  
ex:  
4-2. Than LED display showing: from 00,11, 22, 33, ......88, 99  
4-3. Duplicator will chk itself & get ready.  
Self-Test: Only one segment is running and display "rd" (ready)  
4-4. SmartDup ready, please insert your CD title into your CD-ROM Drive &  
Blank CD-R or CD-RW Media in CD-RW Writer.  
4-5. LED Display showing final counts down, than LED showing H4 or L4.  
Count Down: After drives & discs ready in current mode, wait for  
5 seconds. (Buzzer 0.2s X1)  
ex:  
or  
4-6. LED Display showing CD-R or CD-RW Media maximum writing speed.  
CD-R Maximum Writing Speed:  
or  
or  
4-7. LED Display showing CD-R or CD-RW Media minimum writing time remaining.  
Remain minutes: During Test or Copy mode. Flash every second  
ex:  
or  
or  
4-8. After Test success, Buzzer Beep & LED showing 00. Than re-start Copy.  
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)  
4-8-1. If fail, LED will show: Er & eject CD-R Media also.  
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)  
4-9. LED Display showing CD-R or CD-RW Media maximum writing speed.  
CD-R Maximum Writing Speed:  
or  
or  
4-10. LED Display showing CD-R or CD-RW Media minimum writing time  
remaining.  
Remain minutes: During Test or Copy mode. Flash every second  
ex:  
or  
or  
4-11. After Copy success, Buzzer will Beep & eject CD-R media. LED showing 00  
.
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)  
4-11-1. If fail, LED will showing: Er & eject CD-R Media, Buzzer will Beep also  
.
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)  
SmartDup VP-8220 Operation Manu  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
H5 (Test Only): DIP SW 1 3 4 at ON position, 2 at OFF position--------------  
L5 (Test Only): DIP SW 1 3 at ON position, 2 4 at OFF position---------------  
If you adjust DIP SW to L5, all operation steps same as H5, the Recording  
Speed will drop to 4x only.  
5-1. Turn Rock Switch to position (CD Duplicator). LED will show version  
number.  
Power-On: display firmware version number. (Buzzer 0.5s X1)  
ex:  
5-2. Than LED display showing: from 00,11, 22, 33, ......88, 99  
5-3. Duplicator will chk itself & get ready.  
Self-Test: Only one segment is running and display "rd" (ready)  
5-4. SmartDup ready, please insert your CD title into your CD-ROM Drive &  
Blank CD-R or CD-RW Media in CD-RW Writer.  
5-5. LED Display showing final counts down, than LED showing H5 or L5.  
Count Down: After drives & discs ready in current mode, wait for  
5 seconds. (Buzzer 0.2s X1)  
ex:  
or  
5-5-1. If put in CD-RW Media with Data; CD-RW will eject & show Er.  
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)  
5-6. LED Display showing CD-R or CD-RW Media maximum writing speed.  
CD-R Maximum Writing Speed:  
or  
or  
5-7. LED Display showing CD-R or CD-RW Media minimum writing time  
remaining.  
Remain minutes: During Test or Copy mode. Flash every second  
ex:  
or  
or  
5-8. After Testing success, Buzzer will Beep & eject CD-R media. LED showing  
00.  
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)  
5-8-1. If fail, LED will show: Er & eject CD-R Media also.  
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)  
6
SmartDup VP-8220 Operation Manu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
H6 (Copy Only): DIP SW 1 2 4 at ON position, 3 at OFF position-------------  
L6 (Copy Only): DIP SW 1 2 at ON position, 3 4 at OFF position--------------  
If you adjust DIP SW to L6, all operation steps same as H6, the Recording  
Speed will drop to 4x only.  
6-1. Turn Rock Switch to position (CD Duplicator). LED will show version  
number.  
Power-On: display firmware version number. (Buzzer 0.5s X1)  
ex:  
6-2. Than LED display showing: from 00,11, 22, 33, ......88, 99  
6-3. Duplicator will chk itself & get ready.  
Self-Test: Only one segment is running and display "rd" (ready)  
6-4. SmartDup ready, please inserts your CD title into your CD-ROM Drive &  
Blank CD-R or CD-RW Media in CD-RW Writer.  
6-5. LED Display showing final counts down, than LED showing H6 or L6.  
Count Down: After drives & discs ready in current mode, wait for  
5 seconds. (Buzzer 0.2s X1)  
ex:  
or  
6-5-1. If put in CD-RW Media with Data, CD-RW will eject & show Er.  
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)  
6-6. LED Display showing CD-R or CD-RW Media maximum writing speed.  
CD-R Maximum Writing Speed:  
or  
or  
6-7. LED Display showing CD-R or CD-RW Media minimum writing time  
remaining.  
Remain minutes: During Test or Copy mode. Flash every second  
ex:  
or  
or  
6-8. After writing success, Buzzer will Beep & eject CD-R media. LED showing  
00.  
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)  
6-8-1. If fail, LED will show: Er & eject CD-R Media also.  
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)  
SmartDup VP-8220 Operation Manu  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
H7(High Speed Auto Mode):DIP SW always at ON position------------------  
L7(Low Speed Auto Mode):DIP SW 1 2 3 at ON position, 4 at OFF position-  
If you adjust DIP SW to L7, all operation steps same as H7, the Recording  
Speed will drop to 4x only.  
7-1. Turn Rock Switch to position (CD Duplicator). LED will show version  
number.  
Power-On: display firmware version number. (Buzzer 0.5s X1)  
ex:  
7-2. Than LED display showing: from 00,11, 22, 33, ......88, 99  
7-3. Duplicator will chk itself & get ready.  
Self-Test: Only one segment is running and display "rd" (ready)  
7-4. SmartDup ready, please insert your CD title into your CD-ROM Drive &  
Blank CD-R or CD-RW Media in CD-RW Writer.  
7-5. LED Display showing final counts down, than LED showing H7 or L7.  
Count Down: After drives & discs ready in current mode, wait for  
5 seconds. (Buzzer 0.2s X1)  
ex:  
or  
7-5-1. If insert CD-R Media with Data inside, it will eject & showing Er & if insert  
CD-RW media with data, LED display will showing Er & CA, RW driver will  
eject RW media.  
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)  
7-5-2. If put RW tray in, than LED will show final count down & Erasing RW.  
Count Down: After drives & discs ready in current mode, wait for  
5 seconds. (Buzzer 0.2s X1)  
ex:  
or  
7-5-3.  
Erasing:  
7-6. LED Display showing CD-R or CD-RW Media maximum writing speed.  
CD-R Maximum Writing Speed:  
or  
or  
7-7. LED Display showing CD-R or CD-RW Media minimum writing time  
remaining.  
Remain minutes: During Test or Copy mode. Flash every second  
ex:  
or  
or  
7-8. After writing success, Buzzer will Beep & eject CD-R media. LED showing 00.  
OK: After Self-Test or Test or Erase or Copy. (Buzzer 1sX2)  
7-8-1. If fail, LED will show: Er & eject CD-R Media also.  
FAIL: After Self-Test or Test or Erase or Copy or Upgrade. (Buzzer 0.2X3)  
8
SmartDup VP-8220 Operation Manu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SmartDup VP-8220 Optional interface:  
1. VP-9006: PCMCIA to IDE cable with 36 pin connector.  
2. VP-9007: CardBus to IDE cable with 36 pin connector.  
3. VP-9008: USB 1.1 to IDE cable with 36 pin connector.  
4. VP-9009: FireWire IEEE 1394 to IDE cable with 36 pin connector.  
5. VP-9208: USB 2.0 to IDE cable with 36 pin connector.  
Features:  
1. External CD-RW writer.  
2. Back Up your own Data/ Audio/ Video from HDD/ MO/ LS120/ ZIP... through your  
PC/ Note Book/ MAC to your SmartDup  
HardWare minimum Request:  
1. PCMCIA Type or Type Slot, USB port or FireWire.  
2. Pentium 400 Mhz or Greater.  
3. 64 MB RAM.  
4. USB 2.0 version needs USB2.0 Host Card (VP-9628) or other compatible USB  
2.0 Host Card.  
5. FireWire 1394 IEEE need FireWire 1394 IEEE Host Card (VP-9609) or other  
compatible 1394 IEEE Host Card.  
6. CardBus to USB 2.0: Please make sure your NoteBook PCMCIA Slot support  
CardBus (VP-9728) or other compatible Card.  
7. CardBus to FireWire 1394 IEEE: Please make sure your NoteBook PCMCIA Slot  
support CardBus (VP-9709) or other compatible Card.  
8. One of the Following Operating System:  
(1.) Win 98SE/ 2000/ ME/ MAC os 9.0x for USB 1.1 version.  
(2.) Win 98SE/ 2000/ ME/ MAC os 9.0x for USB 2.0 version  
(3.) Win 98SE/ 2000/ ME/ MAC os 9.0x for FireWire.  
(4.) Win 98SE/ 2000/ ME for CardBus.  
(5.) Win 98SE/ 2000/ ME for PCMCIA.  
Driver Software request:  
1. USB 1.1 version interface: Need install USB drive software under Win 98SE &  
No Need install any USB drive software under Win ME/ Win 2000 & MAC os 9.0.  
2. USB 2.0 version interface: Need install USB drive software under Win 98SE &  
No Need install any USB drive software under Win ME/ Win 2000 & MAC os X.  
3. FireWire IEEE 1394 Interface: No Need install any drive software under Win  
98SE/ ME/ Win 2000 & MAC os 9.0.  
4. CardBus Interface: Need install CardBus drive software under Win 98SE/ ME/  
Win 2000.  
5.PCMCIA Interface: No Need install any drive software under Win 98SE/ ME/ Win  
2000.  
SmartDup VP-8220 Operation Manu  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Install Steps:  
1. Install CD-RW Writer & CD-ROM Driver in each CD-ROM box. Must put rubber  
stand on each CD-ROM box.  
2. CD-ROM Driver on top & CDR or CD-RW Writer on the bottom.  
3. Plug in Duplicator Converter in both CD-ROM box connectors.  
4. Plug in Power Cable in Duplicator Converter.  
5. Plug in Power Cord to AC Power source (+90 ~ +250VAC).  
6. 36 pin IDE cable connect between SmartDup & your PC or Note Book interface  
port.  
7. Turn your Power switch to (PC interface), LED Display will blinking.  
8. Make sure install success.  
9. You can start back-up your Data/ Audio/ Video.  
Caution:  
1. Make sure CD-RW burning software can recognize CD-RW writer.  
2. Make sure your CD-R or CD-RW media acceptable maximum writing speed.  
3. Maximum data transfer rate (byte/sec)  
PCMCIA  
600K  
CardBus  
600K  
USB 1.1  
600K  
900K  
900K  
900K  
900K  
900K  
USB 2.0  
600K  
FireWire  
600K  
4X  
6X  
900K  
900K  
900K  
900K  
8X  
1200K  
2000K  
2000K  
2000K  
1200K  
3600K  
3600K  
3600K  
1200K  
3600K  
4800K  
6000K  
1200K  
3600K  
4800K  
6000K  
24X  
32X  
40X  
4. CD-RW Driver Maximum Writing Speed through PC Interface:  
(1.) PCMCIA: 8 x  
(2.) CardBus: 16 x  
(3.) USB 1.1 Version: 4 x  
(4.) USB 2.0 Version: 20 x  
(5.) FireWire IEEE 1394: 20 x  
New Firm-Ware download:  
1. Same as Install Step 1~ 8 at page 11.  
3. Put CD-RW or CD-R media in to your CD-RW writer.  
4. CD-RW writer as External CD-RW writer.  
5. Start Copy New Firm-Ware to RW media.  
6. Back to Page 3.  
10  
SmartDup VP-8220 Operation Manu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Up-Grade CD-ROM F irm-Ware  
If you wish get best performance on your SmartDup.  
Model number & Firm-Ware Version Number.  
2. ViPowER Inc. CDR/RW Driver Approved List  
Brand  
Acer  
Model Number  
CRW1208A  
CRW9420A  
CRW9624A  
CRW 1232A  
CRW2040  
4424  
Note  
Brand Model Number  
Note  
SeamLess Plextor  
Plextor  
PX-W1210A  
PX-W1610A  
7040A  
AOpen  
AOpen  
AOpen  
AOpen  
BTC  
BurnProof  
Ricoh  
JustLink  
JustLink  
Ricoh  
Ricoh  
Ricoh  
SONY  
SONY  
SONY  
SONY  
SONY  
7060A  
7080A  
MP7200A  
CRX -100E  
CRX -120E  
CRX -140E  
CRX -145E  
CRX -160E  
4416E  
HP  
8100i  
HP  
8200  
HP  
9100  
HP  
9200  
HP  
9300  
Lite-On  
Lite-On  
Lite-On  
Lite-On  
Panasonic  
Panasonic  
Philips  
Philips  
Plextor  
LTR-12101B  
LTR-16101B  
LTR-16102B  
LTR-24102B  
7585  
BurnProof YAMAHA  
BurnProof YAMAHA  
BurnProof YAMAHA  
BurnProof YAMAHA  
TDK  
8424E  
8824E  
2100E  
CRD -BP1300P BurnProof  
CRW54E  
7586  
TEAC  
PCA460RW  
CDD -4801  
PX-W8432T  
TEAC  
CRW512EB  
BurnProof  
Sanyo  
CRD -BP1400  
BurnProof Sanyo  
CRD -BP1500P BurnProof  
3. Best Match (ViPowER will give several suggest for you reference).  
4. Than you can get best performance on your SmartDup.  
5. ViPowER will recommend several match, not only performance, but also easy to  
purchase from any retail chain store near by you.  
6. Do not up-grade by yourself, but you can ask your store up-grade for you.  
7. If you wish up-grade by yourself, please make sure can up-grade success. If fail,  
this CD-ROM driver can't use anymore. On the other hand, most of CD-ROM  
manufacture will not take any responsibility, because up-grade fail.  
SmartDup VP-8220 Operation Manu  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. You can ask your retail store to purchase any brand of CD-ROM driver, which  
ViPowER supply or recommend.  
9. CD-ROM Compatibility List  
CD-RW ACER 52x Afreey 52x AOpen 52x ASUS 52x LITEON 52x TEAC 40x  
8x  
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
12x  
16x  
20x  
24x  
Acer CD-ROM Model Number: CD-652P Version: ??  
AOpen CD-ROM Model Number: CD-952E/TKU Version: C41  
Asus CD-ROM Model Number: CD-S 950/A Version: 1.0D  
AFreey CD-ROM Model Number: CD-2052E Version: V31  
LiteOn CD-ROM Model Number: LTN-526S Version: YS0C  
TEAC CD-ROM Model Number: CD-540E Version: 3.0A  
Or you can send e-mail to us.  
Printed on recycled paper.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Tektronix Network Card DTG5000 Series User Manual
Tektronix Surge Protector cts710 User Manual
Topcom Cordless Telephone ORBIT User Manual
Toshiba Laptop A45 User Manual
Toshiba MP3 Player Portable MP3 Player User Manual
TP Link Network Card TL PA6010 User Manual
Ultra Start Remote Starter 32xx Series User Manual
Universal Remote Control Universal Remote OCE 0040A User Manual
ViewSonic Computer Monitor DSM3210 User Manual
VocoPro Music Mixer PA PRO 900 User Manual