MODEL VP-8059
MODEL VP-8059L
FireWire 1394dock Docking Kit for use with
Mobile Rack Removable Docking Modules
T,
,
with 3.5"/2.5" HDD or Optional zip ,
TM
SuperDisk LS-120, MO, TR-4 Tape,
Digital Film Memory Reader or CD-ROM drives
Installation Manual
TM
We are your DataBridge
Download from Www.Somanuals.com. All Manuals Search And Download.
1-1 Introduction
Congratulations on your purchase of the FireWire 1394dock Docking Kit. The
FireWire 1394dock is an external 1394 interface adapter which is designed to enable
hot-swap,plug-and-playoperationofEnhancedIDEorATA/ATAPIdevicesthrough
the1394interfaceonanyFireWire1394-equippedcomputer.TheFireWire1394dock’s
50-pin connector is designed for use with external devices using the same connector
type (such as CD-ROM) and the Mobile Rack drive case, which provides the perfect
solution for data backup and transporting of data between computers using hard disk
drives,zipdrives,LS-120drives,MO drives,tapedrives,digitalfilmreadersandmore.
TheFireWire1394dockconnectstoanynotebook, iMac, iBOOK, G3/G4, Net-PC,
Micro ATX PC, LCD panel PC, Mac and PC desktop computer equipped with a
FireWire 1394 port. The 1394dock allows you to easily hot-swap various types of
drives mounted in the Mobile Rack without interrupting the current operation.
This manual will guide you through the hardware installation of the following
FireWire 1394dock models:
Model VP-8059 FireWire 1394dock Docking Kit
with Mobile Rack (VP-10LSF)
Model VP-8059L FireWire 1394dock Docking Kit (without Mobile Rack)
1-1.1 FireWire 1394dock Features
• Enables hot-swap Plug-and-Play operation of Enhanced IDE, ATA and
ATAPI devices with computers using the FireWire 1394 interface
• Provides two FireWire IEEE 1394 interface ports
• High performance embedded processor to reduce firmware overhead dual
(ping-pong) buffer to minimize bus latency
• Intelligent interface uses no host CPU resources to control/monitor
time-consuming drive phases other than data transfer
• Complies with the Mass Storage Specification issued by the FireWire 1394
committee, which ensures embedded Mac OS and Windows 98/2000
driver support for Plug-and-Play without additional driver installation
• Proprietary Windows driver supports most devices
• Universal firmware supports all devices, automatic detection for ATA
or ATAPI protocol
• The interface adapter is supplied as a standard OEM board for internal
mounting
• Perfect for adding/sharing external storage devices between computers
using the FireWire 1394 interface
• Actual data rate may vary depending on bus utilization and device
response time
FireWire 1394dock Installation Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1-1.2 ATA/ATAPI Device Compatibility
• ATAPI removable drives: Iomega Zip 100MB/250MB and Clik!,
LS-120 Super Floppy, Sony HiFD 200MB, MO drives, tape drives
• Enhanced IDE and ATA hard drives: both 2.5” and 3.5” form factors,
any capacity
• ATAPI CD-ROM drives: CD-ROM, CD-R, CD-RW, DVD drives,
compatible with all major CD-RW software
• ATA removable media drives: SyQuest SyFlyer, SparQ and Syjet, Castlewood
ORB. Supports media change and disk ejection
1-1.3 Power Requirements
• +5V devices: +5V devices can draw power directly through the 1394 port
connection, the +5V/+12V power adapter, or an optional +5V power adapter
• +5V/+12V devices: +5V/+12V devices require the use of a +5V +12V
AC/DC power adapter (included)
Typical power requirements for ATA/ATAPI device types:
Drive Type
+5V
+5V/+12V
Zip
X
X
X
LS-120 SuperDisk
MO
Tape
X
2.5” HD
3.5” HD
CD-ROM
X
X
X
IMPORTANT
Itisrecommendedthatthe+5V/+12Vpoweradapterbeusedfor
all devices whenever possible to avoid any power problems.
1-1.4 Unpacking Your FireWire 1394dock Docking Kit
Before installing the FireWire 1394dock, verify that the following items are included
in the carton. If any parts are damaged or missing, please contact your local dealer or
sales representative immediately.
• One FireWire 1394dock interface unit
• One +5V +12V AC/DC power adapter and power cord
• One FireWire 1394 cable
• Mounting screws (16 screws) (for Model VP-8059 only)
• One Mobile Rack Stand Set (4 pieces) (for Model VP-8059 only)
• One Mobile Rack (VP-10LSF) (for Model VP-8059 only)
2
FireWire 1394dock Installation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Adapter
Power Cord
+5V/+12V
Power Adapter
Mobile Rack
Docking Case
Mobile Rack
Drive Case
FireWire
1394 Cable
FireWire
1394dock
Mobile Rack
Stand Set
FireWire 1394dock Docking Kit Components (with Mobile Rack)
2-1 Installation
Refer to the following for setup of the FireWire 1394dock for operation.
• For Mac® user’s: A software driver is required for operation of the FireWire
1394dock with Mac computers. This must be purchased separately.
• For use with the Mobile Rack: please refer to the Mobile Rack Installation
manual for instructions for installing devices in the Mobile Rack drive case.
2-1.1 Install Stand Set on Mobile Rack (Model VP-8059)
A 4-piece stand set is included to help heat dissipation and provide secure placement
of the Mobile Rack. After mounting the device in the Mobile Rack, slide a stand pad
onto each corner .
Stand Pad
(With Raised Nub
on Bottom)
(x4)
Mobile Rack Stand Set Installed
FireWire 1394dock Installation Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2-1.2 Setting Up the FireWire 1394dock for Operation
LED Indicators
Power
Drive Activity
50-Pin Centronics
Device Connector
+5V +12V
External
Power Connector
Power On/Off
Switch
FireWire 1394
Connectors
FireWire 1394dock Power Switch & Connector Locations
Perform the following steps (in the order given) to set up the FireWire 1394dock
with your peripheral device for operation:
1. Plug the FireWire 1394dock’s 50-pin connector into the connector on the
device you plan to connect to your computer.
a. External devices that provide a 50-pin Centronics interface connector
support direct connection with the FireWire 1394dock.
b. Internal devices such as EIDE hard drives or ATA/ATAPI devices can be
mountedin theMobileRackdrivecase. (RefertotheMobileRackmanualfor
instructions on mounting these devices in a Mobile Rack.)
IMPORTANT
Make sure the Power switch on the 1394dock is set to the
RIGHT, power OFF position before proceeding.
POWER
ON
OFF
Power OFF
Position
FireWire 1394dock Power Switch Settings
4
FireWire 1394dock Installation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Using the +5V/+12V AC/DC Power Adapter:
a. With the power switch in the OFF position, plug in the 6-pin connector-end
of the power adapter into its corresponding +5V/+12V power-in
connector on the FireWire 1394dock.
b. Plug one end of the power cord into the power adapter and the other end into
an AC power source outlet.
3. Set the power switch to the ON position:
Note that the green LED on the FireWire 1394dock should be lit, indicating
power ON. This allows the device to warm up before connecting to the FireWire
1394 port on your computer.
IMPORTANT
All drive devices must be powered up and ready to use
before plugging into the computer’s 1394 port.
4. Plug one end of the FireWire 1394 cable into the 1394 port on your computer;
plug the other end into one of the 1394 ports on the FireWire 1394dock.
5. Viewing the computer’s monitor screen, note that the plug-and-play feature
will recognize the new device and assign it as a new drive. Hard disk drive
partitions will also be auto-detected and assigned drive letters.
The device is now ready to use.
+5V/ +12V
1394 Port
+5V/+12V DC-IN
1394 Cable
External
Connection Connection
1394 Connector
to Computer
Power Adapter
1394dock
Mobile Rack with
Drive Installed
(or direct connect
to external drive)
Power Cord
FireWire 1394dock Connections for Operation
FireWire 1394dock Installation Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3-1 Disconnecting the FireWire 1394dock
Perform the following steps to disconnect the FireWire 1394dock from your
computer.
1. Turn off the power by sliding the power switch on the 1394dock to the
OFFposition. (Notethat thedriveiconwilldisappearfromthecomputerscreen.)
2. Unplug the 1394 port connector from the 1394dock.
3. You can now switch to another device. When connecting a new device, be sure to
follow the same sequence for setup as previously outlined in section 2-1.2.
4-1 Accessories
Using the optional CD-ROM Box Enclosure, the FireWire 1394dock can be
used to convert ATAPI CD-ROM, CD-R, CD-RW and DVD drives into
external FireWire devices.
Model VP-6020
CD-ROM Box
Enclosure
1394dock Unit
CD-ROM Box Enclosure with
CD-ROM Drive Installed
FireWire 1394dock with CD-ROM Box Enclosure
Printed on recycled paper.
Download from Www.Somanuals.com. All Manuals Search And Download.
|