RV 5100
Mounting instruction
Manuel d’installation
Einbauanleitung
Inbouwhandleiding
Istruzioni d’installazione
Instrucciones de montaje
Monteringsanvisning
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
General
The RV 5100 is a black& white CCD backing up camera designed for use with VDO and
VDO Dayton Multimedia Systems.
Features:
no extra supply voltage needed (12 V power supply by Multimedia System)
automatic switch-on when you shift to the reverse gear (if signal is connected).
high resolution CCD Image Sensor
–
–
–
–
–
–
–
automatic aperture control for optimum adaption to lighting conditions
aperture angle: 130° diagonal
waterproof die-cast camera housing
high operating temperature range
Safety precautions
ATTENTION:
Installation may only be carried out by trained specialists! Observe all quality
standards of the automobile industry!
A
Fire hazard! When drilling pay attention to the location of cable harnesses, tank and
fuel pipes! Never drill into car parts which are load-bearing or are important for safety
reasons!
A
Consult with your authorized car dealer if installation requires the drilling of holes or
other modifications of the vehicle.
A
Refer to the owner's manual for details on connecting the other units, then make
connections correctly.
A
Use only the parts included with the unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions.
A
Route and secure all wiring so it cannot touch any moving parts, such as the gear shift,
handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater
outlet.
A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Scope of delivery
1
1
1
1
1
1
3
3
3
2
2
4
Mounting instructions
Camera with cable (1.15 m) and rubber gasket
Extension cable 18 m
Mounting bracket (stainless steel)
Sun visor (stainless steel)
Strip self-adhesive rubber seal
Self-tapping screws 4 x 10
Spring washers M4
Washers M4
Screws M3 x 6
Spring washers M3
Screws M3 x 8 with spring and washer
Mounting
1. Mount the supplied mounting
bracket to the vehicle with
Self-tapping screw 4 x 10
Spring washer M4
self-tapping srews 4 x 10 and spring
washers and washers M4 (for
example on the plastic bumper).
2. Use self-adhesive rubber seal to
protect vehicle body from scratches,
if necessary.
Mounting bracket
3. If no sufficient hole for the camera
cable is available, drill a hole with a
diameter of 19 mm into the vehicle
body. Deburr all holes and apply
suitable rust protection.
Adhesive tape
Protective paper
4. Pass camera cable through into the
vehicle using the rubber gasket.
Do not bend cable around sharp edges.
5. Mount the camera and the sun visor to the bracket using the 6 supplied screws.
Do not yet tighten screws.
Screws M3 x 8
Sun visor
Spring washer M3
Screw M3 x 6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Connect camera cable as described
in section “Connecting the camera”
on the next page. If required, use
the supplied extension cable.
Connecting the camera
The camera can be connected to your Multimedia System in different ways:
1. Direct connection to the Navigation Computer, ill. 1
For direct connection of the camera to the navigation computer the adaptor cable
MA 1200 (accessory) is required.
Connect the Mini DIN plug of the camera to the Mini DIN socket of the MA 1200.
ꢀ
ꢀ
Activate the “Rear view camera connected” option in the “System Settings –> Video
configuration” menu of the navigation computer.
2. In combination with TV Tuner TV 5100, ill. 2
Connect the Mini DIN plug of the camera to the camera input of the TV 5100.
ꢀ
ꢀ
Connect the yellow lead of the TV 5100 to the reversing signal of the vehicle to
ensure automatic switch over to the camera when backing up.
3. In combination with Multimedia Interface Box MI 5000, ill. 3
Connect the Mini DIN plug of the camera to the camera input of the MI 5000.
ꢀ
ꢀ
Activate the “Multimedia box connected” option in the “System Settings –> Video
configuration” menu of the navigation computer.
4. In combination with TV Tuner TV 5100 and MI Box MI 5000, ill. 3
Connect the Mini DIN plug of the camera to the camera input of the MI 5000.
ꢀ
ꢀ
Activate the “Multimedia box connected” option in the “System Settings –> Video
configuration” menu of the navigation computer.
Checking function and adjusting the camera
1. Switch on ignition.
2. Apply handbrake and select reverse gear.
The picture of the backing up camera has to be shown on the display.
3. Adjust the camera to the desired viewing angle and tighten all screws.
4. Select any forward gear.
The picture of the backing up camera now has to disappear from the display.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Picture system: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/3 inch CCD sensor
Resolution: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270,000 pixel (CCIR)
Horizontal resolution: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380 TV lines
Synchronisation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Hz internal
Lens: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 mm / F = 2.0
Sensitiveness: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0,1 Lux min.
Supply voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . + 12 V / DC
Power consumption: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 W
Operating temperature range: . . . . . . . . . . . . . . . . . . . . . . . . . - 10° Celsius to + 60° Celsius
Dimensions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 mm x 57 mm x 44 mm (W x D x H)
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 g
Connection details
PIN No.
Description
1
2
3
4
5
+ 12 V DC power supply
Video output signal
NC
NC
Ground
Troubleshooting
If you discover any malfunction of the camera after installation, please check all
connections and installation steps according to the mounting instructions.
If you can't solve the problem, please contact our Customer Help Desk:
G
Q
0121 344 5400
(03) 94503166
e-mail: [email protected]
Subject to technical modifications and errors.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
RV 5100
07/2001 ri
Download from Www.Somanuals.com. All Manuals Search And Download.
|