A
S
C
U
S
P
Installation/Operator’s Manual
Model: 1602G / 1802G
Wood or Coal Gravity Style (Up-Flow) Supplemental Furnace
SAFETY NOTICE:
If this furnace is not properly installed, a house fire may result! For your safety, follow these installation
instructions. Contact local building or fire officials about restrictions and installation requirements in your
area. This furnace must be installed by a qualified technician. Keep these instructions for future reference.
Safety Tested to UL 391
United States Stove Company • 227 Industrial Park Road, P.O. Box 151 • South Pittsburg, TN 37380 • www.usstove.com
851768 rev 0
Download from Www.Somanuals.com. All Manuals Search And Download.
CHIMNEY REQUIREMENTS
CREOSOTE - FORMATION AND NEED
FOR REMOVAL
When wood is burned slowly, it produces tar and other
organic vapors, which combine with expelled moisture to
form creosote. The creosote vapors condense in the rela-
tively cool chimney flue of a slow-burning fire. As a result,
creosote residue accumulates on the flue lining. When
ignited, this creosote makes an extremely hot fire.
A fireclay lined masonry or Class A 103HT All-Fuel Metal
Insulated Chimney must be used in all airtight wood fur-
nace installations. The minimum recommended flue size
for the model 1602 is 6 inches, inside diameter and for the
1802, the recommended flue size is 8 inches, inside diam-
eter. When making new chimney installations, always fol-
low the chimney manufacturer’s instructions.
If at all possible, use the factory built, class A 103HT chim-
ney mentioned above. They are safer and perform better
than traditional masonry chimneys. If a masonry chimney
is a must, be certain it has a fire clay liner and that it is
intact, clean and recently inspected. And remember,
masonry chimneys are far more prone to the formation of
hazardous creosote.
The chimney connector and chimney should be inspected
at least twice monthly during the heating season to deter-
mine if a creosote build-up has occurred. If creosote has
accumulated, it should be removed to reduce the risk of
a chimney fire.
SMOKE PIPE INSTALLATION
Clearances to combustible materials (i.e. paneling, ceil-
ing tile, sheet rock, plaster, draperies, casements or wood
trim, etc.) will vary with the type of flue connection used.
Be sure to maintain the specified clearances for your type
of installation.
TYPE OF FLUE
CONNECTION
REQUIRED
CLEARANCE
24 Gauge or Heavier ..................................18”
Single Wall Stainless Steel
or Black Pipe
Double Wall, Stainless Steel or ....................6” Model 1602
Double Wall, Black Pipe w/
Stainless Steel Inner wall
8” Model 1802
Class A 103HT All-Fuel or Equivalent ..........2”
According to NFPA standards, single wall stove pipes
can be within 9” of combustibles provided an approved
fire retardant material covered with 28 gauge sheet
metal, spaced out 1” on non-combustible spacers, is
utilized. See illustration.
1.
The furnace should be the only heating using the
. One furnace per flue outlet.
chimney flue
2. A masonry chimney should have a tile or stainless steel
liner.
3. The masonry chimney should not have any missing
mortar or loose bricks.
4. There should be no mortar or parts of the chimney
blocking the chimney flue.
5. There should be a two inch clearance between any
chimney (masonry or metal) and combustibles. (such
as the house)
When using a Class A or double wall flue pipe connection,
follow the manufacturer’s instructions.
When constructing a single wall smoke pipe, the following
guidelines must be observed.
6. The chimney should extend at least 2 foot above the
highest point of the house, or 2 foot above the point at
which the chimney is 10 foot from the roof.
1. The connector pipe should be 24 gauge or heavier
stainless steel or black pipe.
7. The chimney should be relatively straight and vertical.
2. Secure all joints with three #8 screws.
8. The portion of an all-fuel metal chimney that extends
above the roof should be well secured.
3. If the connector pipe must pass through a wall, an ap-
proved insulated or ventilated thimble, at least three
times the diameter of the smoke pipe must be used.
(i.e. a 6” diameter smoke pipe needs an 18” thimble).
9. A masonry chimney should be built on footings and
not attached to the house.
10. A rain cap, complete with an animal or bird screen,
should be installed on top of the chimney.
USSC
4. Theconnectorpipeshouldneverbeusedasachimney.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Though United States Stove Company expressly Does Not
recommend the use of its furnaces to be installed and/or
used as a free-standing heater, it is possible to achieve a
reasonably safe and functional installation IF certain stan-
dardproceduresarefollowed. Thefollowingareguidelines
onlyandareintendedtoenablethefurnaceusertoobtain
reasonable efficiency from his furnace, and with due re-
spect to safety when installing as a “free-standing heater”.
Ifinstalledcorrectly,andinaccordancewiththeinstructions
foundinthismanual,yourwarmairfurnacemaybeinstalled
as a “space heater” within living quarters, cabins, garage,
or workshop. Please adhere to the following:
IMPORTANT INFORMATION FOR ALL
CONNECTOR PIPES
The connector pipe must be constructed and installed
so that it maintains clearances, keeps condensation and
creosote within the pipe, and is capable of withstanding
a 2100°F degree chimney fire.
1. The connector pipe should slant down toward the fur-
nace a minimum of 1/4” to the foot. At no time should
the pipe turn downward toward the chimney or run
horizontal.
2. There should be no more than two 90 degree elbows.
1. The use of a cold air return and/or filter box is mandatory.
This will not only increase your blower life and provide
filtered air, it will also help prevent the blower or blowers
from “capturing” heated air exiting from the top of the
furnace heat outlets.
3. The connector pipe should never be longer than six
feet. If it is absolutely necessary to make a run of more
than six feet (not recommended) use extra support
brackets every 3 feet.
4. The connector pipe should never be reduced to a
smaller size than flue opening on the furnace.
2. If installed as purchased , without directing the heat
away from the furnace itself, it will simply sit and cycle,
turning the blowers off and on. The thermostat may not
function properly.
5. The connector pipe should not block the flue of the
chimney or extend into it in any way.
6. A good airtight thimble should be used to hold the con-
nector pipe in the chimney. It should be constructed
so the connector pipe can be removed for cleaning.
3. All larger furnaces (or those with multi-speed blowers)
absolutelyrequireBACKPRESSUREtopreventpremature
motor winding failure. If allowed to operate at high RPM
(As in “FREE AIR” mode - no duct work or flow restrictions)
the windings overheat, insulation melts and the motor
simply burns up - not covered under warranty.
7. The connector pipe should not leave the heated por-
tion of the building to reach the chimney.
8. The connector pipe should not pass from one story to
thenextbeforeenteringthechimney, norshoulditpass
through any closed or enclosed space.
CONNECTING HOT AIR DUCT
TO FURNACE
9. The connector pipe and any elbows must be of 24
gauge or greater.
10. The connector pipe should not be located near or in
a walk way or well traveled area.
We strongly recommend that the hot air duct work be
installed by a home heating specialist. If doing the instal-
lation yourself, before you decide which installation will
best suit your needs, consult a qualified heating technician
and follow his recommendations as to the safest and most
efficient method of installation.
11. All male ends of connector pipe should run or point
towards the furnace.
12. Install a cast iron adjustable damper in the first joint of
the connector pipe, nearest to the flue collar.
The following illustrations are the ONLY acceptable con-
figurations when installed with existing oil or gas furnaces.
DAMPERS ON STOVE PIPES
When burning coal, we recommend a Barometric Draft
Damper be installed at a safe convenient place between
chimney and your furnace preferably less than 3’ from the
flue collar.
INSTALLATION EXAMPLES
INSTALLATION #1
With this installation, a back draft damper (optional) is in-
serted into the heat run before the plenum of the existing
furnace to prevent air from the existing furnace to blow
back into the furnace when it is not in use. When a back
damper is employed, it should be located as close to the
existing furnace plenum as practical.
When you have installed the connector pipe between
your furnace and the chimney, tap the pipe hard with
your fingernail. Remember the sound it makes - it will be a
“ting” echoing inside the stove pipe. If later you tap and
hear a muffled thud, you are building up soot in the pipe
and should clean it. This pipe should be cleaned at least
once or twice during the heating season.
DO NOT CONNECT TWO HEATERS TO THE SAME CHIMNEY
FLUE.TheNationalFirePreventionAssociationrecommends
thatwoodburningappliancesventintoaseparatefluefrom
gas or oil furnaces. If such an installation is contemplated,
first check with a local building inspector to find out if a
separate flue for a wood burner is required.
Use of a Barometric Draft Control (when burning wood) is
recommended ONLY in the event your chimney creates
excessive draft leading to an over-firing condition.
HEATED AIR DISCHARGE
The Clayton furnace is designed for use as a supplemental
heating source. When used as a supplementary furnace,
the 1602/1802 is connected in conjunction with an oil, gas,
orelectricfurnacetotheexistingductworkwhichdistributes
the heated air into several rooms and/or areas.
4
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION #2
INSTALLATION #3
Extending the hot air duct from the furnace into the existing
plenum will help direct the flow of air from the furnace as
well as the flow in the existing furnace. Ducting entering
the existing plenum at an angle (approximately 45 degrees)
will facilitate air flow from the furnace while diverting air
from the existing furnace.
The baffle on this system should be made the full width of
the furnace plenum in order to properly direct the air into
the distribution ducts.
THE PLENUM OPENINGS DIFFER
BETWEEN THE 1602 AND 1802
MODEL 1602 - 13” x 18” Rectangular
MODEL 1802 - 18” x 18” Rectangular
RETURN AIR IS VERY IMPORTANT
When installing a Clayton Furnace, return air MUST BE in-
corporated into the system. Return air can be provided
by installing a separate duct system or by tying into the
cold air return of an existing gas or oil furnace. The cold
air return duct can be connected to the furnace with ei-
ther a factory manufactured U. S. Stove filter box, model
UFB908 or an equivalent fabricated from sheet metal.
NEGATIVE
PRESSURE IN
BASEMENT
When installing a cold air return, the minimum size shall
be a 16” x 20” or equivalent (320 sq. in.) in order to insure
proper furnace performance. Failure to provide return air
ducts of the specified size will void your warranty.
A filter should be installed in the cold air return. Furnace fil-
ters should be checked and cleaned/replaced regularly.
COMBUSTION AIR
All fires need air (specifically oxygen) to burn. Furnaces,
fireplaces, and wood burning furnaces need enough oxy-
gen for complete combustion of their fuels. The incom-
plete combustion that takes place when a furnace is “air
starved” causes carbon monoxide (CO) to be formed
in quantities that can be dangerous inside a well sealed
house. Having a source of combustion air from outside
the home will prevent “air starvation” of the furnace. A
simple positive air supply can be constructed using dryer
vent and a modified termination.
If return air is not provided, the warm air distributed into
your home will be restricted and the efficiency of the
furnace is decreased. Without a return air system, warm
air will be drawn into your basement, unnecessarily heat-
ing unused areas of the home. In extreme cases, if your
basement or utility room is fairly airtight, the blowers on
the furnace could depressurize the room and pull toxic
flue gases from the furnace, a gas water heater, or gas
furnace. The fumes could then be distributed throughout
the house.
USSC
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FURNACE ASSEMBLY INSTRUCTIONS
Unpack your Furnace and insure that there is no shipping
damage. If damage exist, please contact your dealer im-
mediately.
Your Clayton Furnace will require some assembly before
operation. All needed hardware and components for the
following assemblies are included within the parts boxes
inside the furnace and in the ash pan. Read and follow
these instructions for proper furnace assembly.
SHAKER GRATE HANDLE
Insert the Shaker Rod into the hole on the ash door frame
as shown. Then attach the Shaker Bracket to the front of
the furnace using two 1/4-20 x 3/4” Hex Bolts and two 1/4-
20 Lock Nuts. Next, insert the shaker Rod into the bracket
and attach to the shaker grate bar using the 1/4-20 x 1”
Hex Bolt and a 1/4-20 Lock Nut. The bolt and nut retaining
the shaker bar and rod should be left loose to allow free
movement of the grates.
DOOR HANDLES
Insert door handle into door. From rear side of door, place
a 1/2” washer over the threaded part of the handle, then
attach the lock nut. Tighten the nut, then back off 1/4
turn to allow free operation of the handle.
(1) Shaker Rod
(1) Shaker Bracket
(1) 1/4-20 x 1” Hex Bolt
(2) 1/4-20 x 3/4” Hex Bolt
(3) 1/4-20 Lock Nut
Follow these same directions for the ash door handle as-
sembly.
BRACKET
(2) Door Handle
(2) 1/2” Washer
(2) 1/2” Lock Nut
ASH DOOR SPIN DRAFT
Screw the spin draft onto the 3/8” x 2-1/2” carriage bolt.
Then screw the spin draft and bolt into the ash door al-
lowing approximately 1/2” of the bolt to stick through the
back side of the ash door. Secure the bolt in place with
the 3/8”-16 lock nut.
(1) Spin Draft
(1) 3/8-16 Carriage Bolt
(1) 3/8-16 Lock Nut
SMOKE CURTAIN
FUEL & ASH DOOR LATCH
With two 1/4-20 x 3/4 hex bolts each, attach the door
latches to the door latch mounting brackets on the left
side of the door frames as illustrated. The slots in the brack-
ets and latches are for door seal adjustment. Make the
proper adjustments, then tighten the nuts. The door’s gas-
ket should be snug against the door frame on the furnace.
Using two 1/4-20 x 1-1/4” Carriage bolts, the smoke cur-
tain clips and two nuts, attach the smoke curtain in place
above the Fuel Feed Door as shown below. After installa-
tion, the smoke curtain should swing freely back into the
furnace.
(1) Smoke Curtain
(2) 1/4-20 x 1-1/4 Carriage Bolt
1/4-20 NUT
(2) Smoke Curtain Clips
(2) 1/4-20 Kep Nut
SMOKE CURTAIN
CLIP
Feed Door
Illustration
Ash Door
Illustration
1/4-20 x 1-1/4
CARRIAGE BOLT
(1) Feed Door Latch
(1) Ash Door Latch
(4) 1/4-20 x 3/4 Hex Bolt
(4) 1/4-20 Kep Nut
SMOKE CURTAIN
NUT
BOLT
SMOKE CURTAIN
CLIP
SMOKE CURTAIN
FRONT
6
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
SPRING HANDLES
WIRING DIAGRAM
Attach the four(4) spring handles to the Feed/Ash Doors,
Baffle Rod, and Shaker Rod by twisting the springs counter-
clockwise while applying pressure until you have screwed
them approximately 3/4”-1” onto the rods.
(4) Spring Handles
DISTRIBUTION BLOWER & ACC.
1. Remove all contents and insure that all components are
present for assembly. See the part list below
2. Begin by attaching the blowers to the unit. Insert a clip into
each mounting hole in the furnace’s cabinet back. Be sure
to install the gasket between the blower and cabinet back.
Insert the eight bolts provided and tighten.
3. Mount the Honeywell limit control to the cabinet back. The
conduit assembly should already be attached to the limit
control, otherwise, do so then make the correct wiring con-
nections to the limit control. See wiring diagram.
4. Next, mount the junction box and insulation using two of the
#10 x 1/2 screws provided. Make a small slice in the 5 x 5 in-
sulation to allow the wires from the draft blower to protrude,
then Install it between the cabinet back and junction box,
with the foil side to the cabinet back. Attach the conduit
assembly from the limit control to the junction box as shown.
5. If not already installed, snap the rocker switch into the top of
the junction box. Provide a 110 volt power supply and con-
nect to the junction box with the cable clamp to the right
side.
6. Attach the two longer conduit assemblies to the junction
box and to each blower.
7. Before mounting the Fan Center, make all the wire connec-
tions per the wiring diagram, then attach the fan center to
the junction box.
All electrical connections should be done by a
qualified electrician.
NOTE: The extra brown wire on the fan center has
no use. It should be capped off or removed.
The conduit may be cut shorter to provide a cleaner
installation.
(2)
(2)
(8)
(8)
(2)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(3)
(1)
(1)
(1)
(8)
800 CFM Blower
Gasket, Blower
Tinnerman Clip, 1/4-20
1/4-20 x 3/4 Bolt
Conduit Assembly (5ft)
Honeywell Limit Control
Conduit Assembly (1ft)
Junction Box
Insulation (5” x 5”)
Rocker Switch
Romex Cable Clamp
Fan Center Control
73B Wire Nut
74B Wire Nut
Female Term. (blue)
Female Term. (red)
#10 x 1/2 Screw
USSC
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FORCED DRAFT BLOWER - 69189
Using two 1/4-20 x 1” bolts and nuts, attach the draft blow-
er adapter to the draft tube on the front of the furnace.
Then mount and secure the draft blower to the adapter
with the three 10-24 Kep nuts. Plug the blower into the out-
let on the front of the furnace.
(1) Draft Blower
(1) Draft Blower Adapter
(2) 1/4-20 x 1 Hex Bolt
(2) 1/4-20 Lock Nut
(3) 10-24 Kep Nut
FIREBRICK AND BAFFLE REPLACEMENT
FIREBOX BRICK REPLACEMENT
BAFFLE/BRICK REPLACEMENT
This furnace comes from the factory with the firebrick in-
stalled. However, if brick replacement is necessary, follow
these instructions. Before furnace operation, remove the
brick retaining strip. This piece is used during shipping to
reduce brick damage.
If baffle replacement is necessary, slide the baffle out until
you can access the nuts thru the flue outlet. Once the
nuts have been removed, slide the baffle off the rod and
thru the opening in the firebrick. You may have to remove
one of the firebrick to make baffle removal easier.
For model 1602, there are 6 full brick and 1 half brick per
side. Install the half brick first by putting the bottom of the
brick in first and let it rest against the firebox side and fire
grates. Then slide it to the rear. After that, install the #2, #3,
#4, #5 & #6 brick, sliding the 6th brick forward to allow for
the 7th brick. Repeat for opposite side.
For model 1602, there are 4 full brick and 1 half brick in the
top of the furnace. Install the brick by inserting one end of
the brick angled upward and then allowing the opposite
end to rest on the firebox lip. Lay the brick between the
spacer and firebox back. Slide the baffle to the rear and
let it rest on that half brick. After installing brick #2 in the
front, install #3 and slide it under the baffle. Finally install
bricks #4 and #5.
For model 1802, there are 8 full brick and 1 half brick per
side. Install the brick in the same manner as previously in-
structed for the model 1602.
For model 1802, there are 6 full brick in the top of the fur-
nace. Install the brick in the same manner as previously
instructed above.
NOTE: Prior to operation, be sure to remove the brick
retaining strips.
8
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
TESTING AND OPERATING PROCEDURES
6. The forced air draft cycles on demand from the wall
GENERAL FURNACE OPERATION
thermostat.SettingtheU.S.Stovethermostatfourdegrees
higher than your existing thermostat is recommended. In
operation, the power draft blower will run until the U.S.
Stove thermostat temperature setting is reached. The
draft regulator on the forced air draft is preset at the
factory and should require no adjustment.
After installation of the furnace is complete, it is ready for
operation. The Honeywell Limit Control, in conjunction
with a wall thermostat, operates the distribution blowers
and the draft blower on the front of the furnace. The limit
control can be adjusted to your desired blower On/Off
times. The factory settings are 100/150/200.
CAUTION: To avoid excessive temperatures, do not
The wall thermostat setting operates the ON time of the
draft blower. If the temperature is below the setting on
the wall thermostat, the draft blower will come on. (Rec-
ommended setting at 5 to 10 degrees higher than other
heating thermostats.)
operate with fuel door or ash pan open.
The first two set points on the limit control operates the
distribution blower(s). When the furnace plenum reaches
the second set point on the limit control, the distribution
blower(s) will come on. If the temperature falls to the first
set point, the distribution blower(s) will shut-off. The rocker
switch on the top of the junction box gives you the op-
tion to run one blower or two. If the switch is ON, both
blowers will come on when the plenum reaches the set
temperature.
STARTING A COAL FIRE
If you burn coal, a forced air draft is required
Shut off FAD when fuel door is open
Open smoke pipe damper all the way. Open all draft
controls on your 1602/1802. Pull the slide baffle forward.
Place about 10-15 lb. of coal in on the shaker grates. It
should come up to about half of the first firebrick level.
Place crumpled paper over the coal and crisscross a
couple handfuls of dry kindling wood 3/4” in thickness
on top of paper.
When the furnace reaches the third set point on the limit
control, the draft blower will shut-off. The draft blower will
come back on if the temperature falls below the setting
on the wall thermostat.
Ignite the paper and close loading door. Wait about 30
minutes until coal fire is established before adding more
coal. NOTE: NEVER load coal over the level of firebrick.
TESTING
Close by-pass damper and set all draft controls to your
own needs. It may take 3 to 4 coal fires to determine
how your local coal and the Clayton Furnace reacts
together. Adjusts drafts accordingly.
1. Check the draft blower by turning the room thermostat
up high enough so that the draft blower turns on. Then
lower the thermostat setting until you hear it shut off.
2. Use a sheet of newspaper to test your draft by placing
it inside the furnace and lighting it.
Loading with a good bed of coals in the morning - Open
by-pass damper.
With completion of the tests above, you are ready to light
the furnace. Follow the operating steps.
1. Innormalshaking,onlyrockthegratesasmallamount
to sift ash through. Do not agitate the fire bed too
often. This practice will waste coal. If glowing coal is
visible in the ash pan, you have shaken to much.
STARTING A WOOD FIRE
Using Forced Air Draft
2. Remove all ashes every day from ash pit.
CAUTION: Never use gasoline, gasoline-type lantern fuel,
kerosene, charcoal lighter fluid, or similar liquids to start or
“freshen up” a fire in the furnace. Keep all such liquids well
away from the furnace while it is in use.
CAUTION:Ashesshouldbeplacedinametalcontainerwith
a tight fitting lid. The closed container of ashes should be
placed on a non-combustible floor or on the ground well
awayfromallcombustiblematerialspendingfinaldisposal.
If the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in the closed
container until all coals have thoroughly cooled.
1. Open spin draft cap on ash door.
2. Pull the slide baffle rod to the front position.
3. With your poker, push hot burning embers to the rear
of the unit and add green coal in front. NEVER load
over height of firebrick. This can result in damage to
your furnace and home.
3. Open the fuel load door and light fire using kindling and
severalsheetsofnewspaper,thenclosethefurnacedoor.
Thefurnacedoorshouldremainclosedfor5to10minutes
in order to establish the fire. If the fire has established, you
are ready to load the furnace.
4. Close by-pass damper.
Too much draft air will cause clinkering of coal and will
waste heat up the chimney. Shut draft down to as low
a point as you can and still heat your home.
CAUTION: To prevent flame and smoke spillage, the slide
bafflemustbepulledoutandthefueldoormustbecracked
for ten seconds before being fully opened.
1. NOTE: Never stand in front of loading door when
opening it. Stand to the side.
Do not over fire your furnace! After you have become
familiar with its operating, you should know how much
wood to use.
2. NEVER completely cover the live fire with fresh coal.
Always leave a generous area of glowing coal at the
top of the fire and at the rear.
4. Load the furnace, close the load door and push the slide
Baffle rod to rear.
3. Always keep the ash pit clean.
5. Close the spin draft cap on ash door, leaving it cracked
about the diameter of a dime.
USSC
9
Download from Www.Somanuals.com. All Manuals Search And Download.
If the fire goes out or does not hold overnight, look for:
1. Poor draft.
Inspectandcleanyourchimneyandstovepiperegularly.
In event of chimney fire, shut all draft controls and call
your fire department immediately. Alert everyone in the
house. If the fire is still burning vigorously, throw baking
soda into firebox or discharge a fire extinguisher into the
firebox. After chimney fire is over, completely inspect
system for damage before further use.
2. Incorrect damper settings.
3. Improper firing methods for coal being used.
4. More combustion air needed.
5. Coal not sized to the furnace. We recommend 1” to
3” diameter pieces of coal.
NEVERthrowwateronthefireoratthefurnace,asrapidly
expanding steam could result in a severe scalding.
6. Ashes, if allowed to accumulate in the ash pit, will
not allow the passage of required air for combustion.
Keep ash pit clean.
Slow fires: It is not recommended burning the Clayton
furnace any more than necessary early in the fall and
late spring, as you cannot keep the firebox hot enough
(without overheating your home) to burn gases. Slow
fires can cause excessive creosote build-up in smoke
pipe, chimney and firebox.
7. Thisfurnaceisnottobeusedwithanautomaticstoker
unless so certified.
There are ONLY two types of coal allowed for use in this
furnace: Bituminous Coal (soft coal) and Anthracite
Coal (hard coal). NEVER USE Cannel (or Channel) coal
or Brown (Lignite) Coal.
Woodshouldbeplaceddirectlyontothecastironshaker
grate of the Clayton furnace. Do not use additional
grates and/or irons.
See our Bulletin RC454 at the rear of this manual for the
In the event of a power failure, you may operate the
1602/1802 furnace provided the following instructions
are followed:
best information available on burning coal.
OPERATING NOTES
1. Any air filter should be removed.
Do not over draft the furnace! It is designed to operate
at .06 inches of water column and must be set with a
draft gauge to maintain a steady draft. (Barometric
Damper recommended.)
2. Observe the furnace operation closely and often till
power is restored.
Do not burn garbage, plastics, gasoline, drain oil or
other flammable liquids. Plastics, when burned, form
hydrofluoric and hydrochloric acids which will dam-
age and destroy your furnace pipe and chimney. The
burning of trash or oil can result in an extremely hot fire
and is sometimes a cause of chimney fires. NEVER BURN
GREEN WOOD OR TIRES.
Do not allow ashes to build up higher than 2” above
grates.
Never allow the ashes in the ash pan touch the grate
section. REMOVE ASHES FREQUENTLY!
Be extremely careful when removing furnace ash pan;
it can get very hot.
Do not store fuel or other combustible material within
marked installation clearances.
With new steel, there is a small amount of oil or dirt on the
metal. You may smell an odor. This is normal during the
first operation. You may want to assemble the furnace
out of doors and build a small fire in it to “burn off” this
dirt and oil before installing the unit.
NOTE: For further information on using your furnace safely,
obtain a copy of the National Fire Protection Association
publication “Using Coal and Wood Stoves Safely.” NFPA
NO. NW-8-1974. The address of the NFPA is 470 Atlantic
Ave., Boston, Massachusetts 02210.
The furnace is designed to burn air dried wood and coal
at a predetermined firing rate. Over firing could result
in damage to the heat exchanger and cause danger-
ous operation. Over firing occurs when the ash door is
left open during operation or a highly volatile fuel, i.e.
large amounts of small kindling, is used. If any portion of
the connector pipe glows orange or red, you are in an
over-firing situation. Close all dampers.
THIS IS A WOOD AND COAL BURN-
ING FURNACE AND SHOULD NOT BE
ALTERED IN ANY WAY! DOING SO
WILL VOID YOUR WARRANTY!
When tending the firebox always pull the baffle slide rod
out prior to opening load door. Open load door slowly
to avoid a “flash back”. After closing load door, push
the baffle slide rod to the rear.
Equip your home with fire extinguishers and smoke de-
tectors appropriately located.
Inspect air filters regularly. The air filter in the filter box
should be changed at least every 30 days.
Oil motor on forced air draft every 90 days with a few
drops of 30 wt. oil.
The distribution blower motors may be one of two types.
If the motor has sealed bearings, no oiling is required.
If the motor is equipped with fill holes, the motor should
be oiled every 90 days with several drops of 30 wt. oil.
Check the fit on the load door. It must fit tightly. If it does
not, check for deterioration or wear of the ceramic rope
seal. Replace defective seals.
10
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING AND PROBLEM SOLVING
4. Problem:
1. Problem:
Smoke puffs from furnace
Distribution blower vibrating
Solution:
Solution:
A. Tighten blower wheel to motor shaft.
B. Check for bad fan bearings.
A. Check chimney draft. Check for blocked chimney
orfluepipe.Usemirrortocheckchimneyclearance.
B. Check ash pit — if it is too full, empty.
5. Problem:
C. Make sure furnace room is not too airtight.
Distribution blower continues to run or will not run
Solution:
D. Make sure all of chimney mortar connections are
airtight.
A. Check fan limit or heat sensor and cable.
E. Check ash drawer. Make sure it’s airtight.
B. Check to see that blower is properly wired.
(See Wiring and Assembly Instructions).
F. Check chimney for possible down-draft caused
by taller surrounding trees or objects. Correct with
proper chimney vent cap.
C. Check fuse box or power source.
D. Check power supply.
G. Check the possibility of a cold chimney forcing cool
gases backward. Remedied by properly insulating
chimneywithnon-combustibleliner—non-combus-
tible insulation.
6. Problem:
Draft blower continues to run or will not run
Solution:
H. Fuel may be too green.
A. Check wiring.
I. Make sure no other fuel burning devices are con-
B. Check thermostat or thermostat wire for short.
C. Make sure temperature is calling for heat.
nected to the chimney impairing the draft.
J. Check chimney draft, it should be .06 inches of
water column. This service is provided by a certified
chimney sweep.
7. Problem:
Odor from first fire
Solution:
2. Problem:
A. The odor from new steel should disappear in a few
hours.
Inadequate heat being delivered to your home
Solution:
B. If the odor remains, call you dealer immediately. A
bad weld can cause a fume leak.
A. Check home insulation — is it adequate?
B. Checkhook-uptofurnace—isitinstalledcorrectly?
8. Problem:
C. Cool air inlet may be inadequate or furnace room
too airtight.
Excessive Creosote
Solution:
D. Your wood fuel may be too low grade. Hardwoods
are recommended.
A. Check the grade of wood you are burning.
B. Make sure your unit is serviced by its own proper
chimney.
E. Make sure your hot air duct (and other duct work)
is airtight.
C. Check length of flue pipe and its connections.
F. If furnace room is warm but your home isn’t, check
back draft dampers.
D. Make sure you are burning the smallest, hottest fire
to adequately heat your home.
G. Is air to the blower available?
E. Also see Solutions to Problem one.
3. Problem:
9. Problem:
Excesssmokeorflamescomingoutdoorwhenrefueling
If the fire goes out or does not hold over night
Solution:
Solution:
A. Wait 15 seconds and open door SLOWLY — then
refuel.
A. Poor Draft.
B. Incorrect damper settings.
C. Improper firing methods if burning coal.
D. More combustion air needed.
B. Check length of flue pipe to chimney. Your unit
should be within six (6) feet of your chimney.
C. Make sure chimney cap is not too close to the top
of the chimney.
E. Coal not sized to the furnace. We recommend 1”
to 3” diameter pieces of coal.
D. Check chimney draft — make sure chimney flue
pipe is clean and chimney is of adequate height.
F. Ashes, if allowed to accumulate in the ash pit, will
notallowpassageoftherequiredairforcombustion.
Keep ash pit clean.
E. Make sure you’renot suffocating thefirewith exces-
sive amounts of unburned wood.
F. Slide baffle should be pulled out prior to load door
opening.
G. This furnace is not to be used with an automatic
stoker unless so certified.
USSC
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DIAGRAM
23
35
34
28 29
30
34
33
22
36
21
20
18
19
3
16
17
4
3
2
1
27
25
26
37
3
24
15
8
9
7
10
6
14
17
16
2
3
5
31
32
13
12
11
12
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DIAGRAM AND LIST
Key Description
Part #
69091
24179
83444
83835
89574
23786
68880
23859
23823
C21399
69005
24204
Qty
Key Description
Part #
23817
Qty
1
1
Feed Door Assy. (w/Rope Gasket)
Door Handle
1
36
Front Filler
P
Front Filler - 1800
24190
1
2
2
37 Draft Cover
23818
24508
1
N/S Lock Nut, 1/2-13
N/S Washer
2
P
38
39
40
41
42
43
44
45
46
47
48
49
50
Draft Cover - 1800
1
2
Room Blower - 800 CFM
Blower Gasket
80530
88127
83340
83339
69578
80145
68859
25625
25626
C42373
80362
80130
23819
2
2
8
8
2
1
1
1
1
1
1
1
1
3
4
5
6
7
Spring Handle
4
Feed Door Latch
Ash Door Assy. (w/Rope Gasket)
Draft Cap
1
Tinnerman Clip, 1/4-20
Bolt, 1/4-20 x 3/4
1
1
Conduit Assembly (5ft)
Honeywell Limit Control
Conduit Assembly (1ft)
Junction Box
Ash Door Latch
1
N/S Hinge Pin, 5/16” x 1”
4
8
Shaker Handle
1
9
Bracket, Shaker Handle
1
Insulation (5” x 5”)
Rocker Switch
10
Ash Pan
68882
68919
1
P
Ash Pan - 1800
1
Romex Cable Clamp
Fan Center Control
Water Coil Access Cover
11
Grate Retainer
40312
40337
2
P
Grate Retainer - 1800
2
12
Shaker Bar
891341
1
5
13
Shaker Grate Section
40314
.............
N/S = Not Shown
P = Items designated for model 1800
P
Shaker Grate Section - 1800
7
1
1
14
Back Liner
40313
40339
1
1
IMPORTANT NOTE:
P
Back Liner - 1800
When ordering repair parts, a color code (G) should be placed
after the part number of any part that is painted.
15
Front Liner
40344
40338
P
Front Liner - 1800
46
47
16
P
Full Firebrick (4-1/2 wide x 9 tall x 1-1/4 thick)
..............................................................................
89066
.............
16
22
17
P
Half Firebrick (2-1/4 wide x 9 tall x 1-1/4 thick)
..............................................................................
891414
.............
3
2
45
48
18
Slide Baffle
24231
1
1
19
Baffle Rod
86603
P
Baffle Rod - 1800
86607
1
20
21
22
Lock Nut, 1/2-13
Gasket, Flue Collar
Flue Collar
83444
88032
40246
2
1
1
1
43
44
23
P
Flue Collar Ring
Flue Collar Ring - 1800
22761
23958
1
24
25
26
27
Smoke Curtain
23800
23787
83445
83250
1
2
2
2
Smoke Door Clip
49
50
Carriage Bolt, 1/4-20 x 1-1/4 Long
Kep Nut, 1/4-20
28
P
Cabinet Side, Left
Cabinet Side, Front Left - 1800
68821
68962
1
1
42
39
40
29
P
Insulation, Side
Insulation, Side - 1800
C98771
23977
2
2
30
Insulation Retainer
83884
41
1
31
P
Cabinet Side, Right
Cabinet Side, Right - 1800
68822
68961
1
38
41
N/S Cabinet Side, Back - 1800
69002
80351
2
1
1
32
Receptacle, Snap-In
33
Cabinet Back
69573
69613
P
Cabinet Back - 1800
1
34
P
Insulation, Panel
Insulation, Back - 1800
C98871
23978
2
2
2
P
Insulation, Top - 1800
23979
35
P
Cabinet Top
Cabinet Top - 1800
69088
68964
1
1
USSC
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS DIAGRAMS AND LISTS - 69189
1
2
4
3
5
Key Description
Part #
69190
69192
83379
83261
83244
Qty
1
2
3
4
5
Drqft Blower Assembly
1
1
2
2
3
FAD Bracket
Bolt, 1/4-20 x 1”
Lock Nut, 1/4-20
Kep Nut, 10-24
UFB908 COLD AIR RETURN / FILTER BOX - OPTIONAL KIT
As mentioned earlier in this manual, a cold air return and/
or filter box should be incorporated into your furnace in-
stallation. A cold air return or filter box will increase the life
of your blowers and offer filtered distribution air for your
home. U.S. Stove offers the model UFB908 as an option
and can be purchased from your local dealer.
The UFB908 utilizes a standard 16” x 20” filter that can be
purchased from your local dealer or any hardware/duct
work supply store. When installing a UFB908, follow the in-
stallation instructions supplied with the kit.
14
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
DOMESTIC HOT WATER COIL KIT - OPTIONAL
This Furnace will accept the installation of a Domestic Hot
Water Coil Kit. The U.S. Stove kit is a 1124 Water Coil and it
may be purchased from your local dealer.
2
1. Remove the access panel on the rear of the furnace
enclosure.
2. With a utility knife, cut away a section of the insulation
(if equipped) directly behind the access panel.
1
3. Remove the cover plate from the rear of the furnace
firebox.
ACCESS
PANEL
4. Place one nut on each end of the water coil and
thread each nut up to the end of the threads on the
coil.
5. Insert the coil through the holes from the inside of the
firebox. Install a gasket, washer and nut onto each end
of the water coil. Tighten the nuts down securely to in-
sure an air tight seal.
The installation is now ready to be plumbed to your exist-
ing hot water system. Choose one of the three methods
described in the Hot Water Coil instructions.
3
6. Remove knockouts from the access panel and re-attach
to the furnace enclosure.
REAR WALL OF
FIREBOX
Have a qualified plumber connect your domestic hot water
pipe to the coil with the appropriate fittings.
5
4
DOMESTIC HOT WATER
COIL
6
TURN INSIDE NUTS UP
TO END OF THREADS
1. NUT
2. WASHER
3. GASKET
DR6 - 6” DRAFT REGULATOR KIT - OPTIONAL KIT
In the unlikely event that your furnace “overfires” (a con-
dition evidenced by elbows, stove pipes, and connec-
tors glowing red in appearance or otherwise discoloring),
then your installation is subject to excessive draft created
by either a chimney too tall or too great in diameter in
conjunction with its height, or some other factor of an
indeterminate cause. In this event, you should install a
barometric draft regulator. Such installation will preclude
any over-firing and/or any hazardous consequences of
potential overfiring.
Barometric draft regulators are generally available where
you purchased your stove or may be ordered directly
from United States Stove Company at a nominal charge.
USSC
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BULLETIN RC454
A GUIDE TO BURNING COAL IN YOUR FURNACE
Furnaces that are capable of burning coal usually
orange or yellow and produce quite a bit of smoke.
As the gases burn off the flames become shorter,
change color and produce less smoke.
will burn both Bituminous and Anthracite coal. An-
thracite is perhaps the best coal fuel because of its
long even burn time, high heat output, and cleanli-
ness which make it a good choice for the home.
However, keep in mind it is a much more difficult
fuel to use, requires more care and patience, is not
so widely available, and is usually much more ex-
pensive than Bituminous.
Once the fire is WELL ESTABLISHED add coal to the
center of the firebox forming the cone. Burning in
this fashion allows heat to drive off the volatile gases,
and turbulence created increases the burn efficien-
cy. There will have to be some experimenting with
the individual setup as no two chimney’s or instal-
lations are going to be the same. Just remember to
allow enough air to enter the firebox and keep the
stove pipe damper open so that volatiles are prop-
erly burned. Before refueling, take the time to break
up the cone a little with a poker, especially if it has
caked over or formed a crust. But, be careful not to
mix the coal as this increases the chances of form-
ing clinkers. When shaking the grate(s) be gentle.
Just a few short movements - a couple of “cranks”
- is better than a lot of agitation. The objective is to
remove a small amount of the ashes without disturb-
ing the fire. Stop when you see a glow in the ashes
or the first red coals fall into the ash pan. Excessive
shaking wastes fuel and can expose the grate(s) to
very high temperatures which can cause warpage
or burnout.
SIZE OF COAL:
Most sizes of Bituminous Coal will work in a coal fur-
nace; for best results we recommend large “nut”
coal to small “egg” coal (1-3/4” diameter to 4” di-
ameter). When burning Anthracite, use “egg” or
“broken” with sizes between 2-5/16” thru 4-3/8”.
Note that it is important to the long life of your stove
to buy coal which has been sized and cleaned.
Cleaning insures removal of rocks and other miner-
als. Never use coal smaller than 1” or larger than
5” in diameter. Small sized coal will smother the fire.
Too large a size of coal will not burn well.
STOVE OPERATION:
All coal fires should be started with wood which will
allow the fire to get hot enough to ignite the coal.
The best ignition fires utilize dry pine or other resinous
soft woods as kindling, with hard wood (oak, hicko-
ry, ash) added to increase the heat prior to addition
of the coal.
For overnight operation (long duration burn time)
shake the fire and add coal, retaining the center
cone. Once the volatiles are burned off, close the
feed door and adjust the stove pipe damper, if
epuipped. Then adjust the thermostat to the desired
heat level.
Before starting the fire, open the stove pipe damp-
er (if epuipped), turn the thermostat to high, open
the ash pit door and feed door, place newspaper
and finely split kindling on the grate, light the paper,
add larger hard wood after the kindling is burning
brightly. CAUTION: Never use gasoline, lantern fuel,
kerosene, charcoal lighter fluid, or other flammable
liquids to start or freshen up a fire in any heater.
Place the larger pieces of wood on the fire so that
they are slightly separated and form a level for the
addition of coal. It will take 10 to 20 minutes before
this wood is thoroughly ignited. Adding coal too
soon will cut the air supply and smother the fire.
More MAINTENANCE will be needed with bituminous
coal than with anthracite coal as more soot will
collect on heating surfaces and in pipes, requiring
more frequent cleaning.
ANTHRACITE:
Add a thin layer of coal (preferably smaller chunks)
to the wood fire, being careful not to disturb it too
much or cut off the draft. Then, add a second
heavier layer after the coal is ignited and burning
well. If necessary, add a third layer to bring the coal
up to the top of the front liner (not above!). Be sure
to close the ash door.
BURNING BITUMINOUS:
Once your kindling and wood fire has produced a
bed of well established coals, start adding coal in
layers allowing each to ignite before adding more.
Bituminous has a high volatile content and, as a re-
sult, should be fired with the “conical method” - with
the highest portion of your fire bed in the center of
the firebox. The first flames will be long and generally
Before adding further fuel, be sure to leave a red
spot of glowing coals in the center of the firebox to
insure that the fire has not been smothered and to
help ignite the gases given off by the new charge.
A deep charge will give a more even heat and a
longer fire, but it may take one to two hours before
the whole bed is fully ignited.
16
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
BULLETIN RC454
A GUIDE TO BURNING COAL IN YOUR FURNACE
When the fire is well established and the room is be-
BANKING THE FIRE:
coming warm, partially close the dampers. Some
experimenting will have to take place with each
particular setting of all dampers and controls as the
chimney provides the draft necessary to not only
exhaust the smoke, but to pull combustion air into
the heater as well - and no two chimney’s perform
the same. Under ideal draft conditions, one should
be able to turn the secondary air supply below the
feed door (some models) to a near closed position -
but leave the ash pit damper at least partially open
to prevent the fire from going out. Adjust the stove
pipe damper to reduce the draft on the fire. With
anthracite there will be short blue flames above
the coal, except when the fire is started or a new
charge is added. If, however, there is no flame then
the fire needs more air from the bottom (unless it is
near the end of its burn cycle and needs to be re-
charged).
For extended operation, such as overnight, the fire
will need to be banked. To do so heap coal up
along the sides and back of the firebox so that the
fire gradually burns it over a longer period of time.
The intensity of the fire will also be reduced without
letting it go out. Follow the same procedure as for
refueling. If possible, avoid shaking, as a heavier
layer of ash will help reduce the intensity of the fire
during this time. After loading, let the fire establish
itself for about 30 minutes. Then close your damper
and automatic control to the point where the house
does not become too cold. It is important that you
begin banking early enough before retiring or leav-
ing that you can make necessary adjustments after
the fire is well established.
To revive a coal fire that is almost out, (1) open the
ash door and stove pipe damper and close the spin
damper under the door to get a good draft through
the grate. (2) place a thin layer of dry coal over the
entire top of the fire. DO NOT POKE OR SHAKE THE
FIRE AT THIS TIME! (3) after the fresh coal has become
well ignited shake the grate (just a little), refuel.
Only when the coal is burned down to half its origi-
nal depth it is time to add fresh coal. When doing so,
open the stove pipe damper and turn the thermo-
stat damper to high, which will allow the fire to burn
off any accumulated gases. Open the feed door,
and with a small rake, hoe, or hooked poker pull the
glowing coals to the front of the firebox. Try not to
disturb the fire too much. Next, add a fresh charge
to the back being careful not to seal off the top.
Close the feed door, but leave the spin damper (or
thermostat) open for a few minutes until the volatile
gases have burned off. It is not necessary to shake
down the ashes each time you refuel the furnace.
Experience will be your best teacher.
DO NOT burn coke, charcoal, high volatile bitumi-
nous coal, sub bituminous, lignite or cannel coal
(sometimes called channel coal or candle coal).
NEVER burn wax or chemically impregnated saw-
dust logs - their intended use is for fireplaces only.
NEVER fill the stove or furnace above the firebrick or
cast iron liner.
USSC
17
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
18
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
USSC
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPAIR PARTS
This manual will help you obtain efficient, dependable service from the fur-
nace, and enable you to order repair parts correctly.
Keep this manual in a safe place for future reference.
When placing an order or for warranty claims, please provide the following
information found on the Certification Plate located below the ash door.
PART NUMBER
PART DESCRIPTION
MODEL NUMBER - 1602 / 1802
SERIAL NUMBER______________
United States Stove Company
227 Industrial Park Road
P.O. Box 151
South Pittsburg, TN 37380
(423) 837-2100
Customer Service: (800)-750-2723 • Repair Parts: (888) 299-1440
20
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
|