Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and functions
1
2
5
14
15
16
17
18
6
7
8
9
talk
batt
mute
vol
talk
flash
mute
int'c
mem
abc
jkl
def
1
2
5
8
0
3
6
9
ghi
mno
wxyz
4
pqrs
tuv
7
10
oper
3
4
tone
11
12
13
19
20
redial
pause
ringer
chan
e x t e n d e d
r
a n g e
21
DIGITAL 900MHz
38
23
24
25
39
40
clock
pin
volune
status speaker
26
27
28
29
30
31
32
41
42
43
delete
play
DIGITAL
greeting
voice memo
ans on/off
memory
redial/p
flash
44
45
46
47
speaker
mute
page/int'com
extended range
22
33
34 35 36 37
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Handset antenna
2. Headset jack cover
3. Handset battery compartment
4. Handset ring switch
5. Handset speaker
6. Talk/Batt LED
7. Talk key
22. Base microphone
23. Speaker LED
24. Status LED
25. Handset retainer clip
26. Clock key
27. Pin code key
28. Delete key
8. Volume down key
9. Mute key
29. Greeting key
30. Repeat key
10. Tone key
31. Skip key
11. Redial key
12. Pause key
13. Handset microphone
14. Mute LED
32. Voice memo record key
33. Base battery contacts
34. Tone key
35. Mute key
15. Volume up key
16. Flash key
17. Memory key
18. Intercom key
19. Channel key
20. Ring key
36. Speaker key
37. Page/Intercom key
38. Base speaker
39. Volume down key
40. Volume up key
41. LED display
21. Handset battery contacts
42. Play/Stop key
43. Base antenna
44. Answer on/off key
45. Memory key
46. Redial/Pause key
47. Flash key
48. Record time switch
49. Ring time switch
50. Ring volume switch
51. Pulse-Tone switch
52. DC power input
53. Phone jack
AN4/1
48
49
RCTIME
24/TS
RNGTIME
50 51 52 53
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Contents
Introduction / Features...............inside front cover
Controls and Functions ..............inside front cover
Basics
Getting Started
Read this first..........................................................3
Step 1: Checking the package contents ...............4
Step 2: Setting up the base unit ...........................5
Mounting the base unit on a wall ...........8
Step 3: Preparing the battery pack .....................10
Memory Dialing
Basics
Making a call ........................................................12
Receiving a call ....................................................13
Adjusting ringer and ear speaker volume ..........14
Redialing a call.....................................................15
Mute ......................................................................16
3-way
Conference
Features
Memory Dialing
The Integated
Answering
devise
Storing phone numbers .......................................17
Making calls with memory dialing......................18
Erasing a stored phone number..........................19
3-way Conference Features
3-way conferencing..............................................20
Using your EXA 8955 intercom...........................21
Transferring a call.................................................22
Additional
Information
The Integrated Answering Device
Features.................................................................23
Setting up your answering system ......................24
Using your answering system .............................28
Troubleshooting
Specifications
Index
Additional Information
Changing the digital security code......................34
Installing the beltclip............................................35
Headset installation ..............................................35
Note on power sources .......................................36
Maintenance..........................................................36
Troubleshooting..................................................37
Specifications.......................................................39
Index .....................................................................40
Download from Www.Somanuals.com. All Manuals Search And Download.
Read this first
This cordless telephone must be set up before use. Follow these steps;
Step 1
(page 4)
Unpack the telephone and accessories.
Step 2
(page 5 to 9)
Next, choose the best location to set
up the base unit.
Base unit
Step 3
(page 1 0 to1 1 )
Then, insert the battery pack into the handset.
You have to charge the battery pack for more
than 12 hours before using the phone.
Handset
About the digital security code
This cordless telephone uses a digital security code to prevent
unauthorized access to your base unit. This security code prevents
other cordless handsets from making calls through your base unit.
A random security code will be assigned automatically between
your base unit and handset when you charge the battery pack for
the first time.
If you want to reset the security code, see page 34.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the package contents
Make sure you have received the following items in the package.
If any of these items are missing or damaged, contact the Uniden
Parts Department (see below).
• Base unit
• Handset
• AC adapter (AD-420)
• Rechargeable
battery pack
(BT-905)
• Telephone line
cord (2)
• Wall mount adapter
• This Owner's Manual
• Precautions and Important Safety Instructions
• Registration Card
• Beltclip
Uniden Parts Department
(800) 554-3988
Hours: M-F 8:30 AM to 5:00 PM CST.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the base
Do the following steps.
• Choose the best location
• Connect the base unit
• Choose the dialing mode
Choose the best location
Before choosing a location for your new phone, read the
INSTALLATION CONSIDERATIONS included in the PRECAUTIONS
AND IMPORTANT SAFETY INSTRUCTIONS brochure. Here are some
important guidelines you should consider:
Avoid heat sources, such as
radiators, air ducts, and sunlight
Avoid noise sources such as a window
by a street with heavy traffic
Avoid microwave ovens
Avoid television sets
and other electronic
equipment
Avoid excessive
moisture, extremely low
temperatures, dust,
mechanical vibration, or
shock
Avoid personal
computers
Choose a central location
Avoid other cordless
telephones
• You should charge your handset for 15-20 hours before using
the phone.
• The location should be close to both a phone jack and continuous
a power outlet which is not switchable.
• Keep the base and handset away from sources of electrical noise
such as motors and fluorescent lighting.
• Be sure there is sufficient space to raise the base antenna
fully vertical.
• The base can be placed on a desk, tabletop or mounted on a
standard wall plate.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the base unit
If you want to install the base unit on the wall, see page 8.
Route the cord.
Place the power cord so it
does not create a trip
hazard, or where it could
become chafed and create
a fire or electrical hazard.
2
To AC outlet
To DC IN 9V
AC adapter
(supplied)
1
To telephone outlet
To TEL LINE
Telephone line cord
(supplied)
1
2
3
Connect the telephone line cord to the TEL LINE jack and to
a telephone outlet.
Connect the AC adapter to the DC IN 9V jack and to a
standard 120VAC wall outlet.
Set the base unit on a desk or
tabletop and place the handset
on the base unit.
Then raise the antenna to a
vertical position.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Use only the supplied AD-420 AC
adapter. Do not use any other AC
adapter.
Polarity of the plug
Connect the AC adapter to a
continuous power supply.
Place the base unit close to the
AC outlet so that you can unplug the
AC adapter easily.
Modular
If your telephone outlet isn't modular,
contact your telephone company for
assistance.
Choose the dialing mode
PULSE
TONE
Depending on your dialing system, set the TONE/PULSE switch as
follows:
If your dialing system is Set the switch to
Tone
Pulse
TONE
PULSE
If you aren't sure of your dialing system
Make a trial call with the TONE/PULSE switch set to TONE.
If the call connects, leave the switch as is; otherwise, set to PULSE.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the base unit on a wall
Standard wall plate mounting
This phone can be mounted on any standard telephone wall
plate.
1
2
Snap the wall mount
adapter into the
notches on the base.
1
Plug the telephone
line cord to the
TEL LINE jack and the
AC adapter to the
DC IN 9V jack.
3
4
Plug the telephone
line cord into the
telephone outlet.
2 - 7
Wrap the AC adapter
cord inside the
molded wiring
channel. Then wrap
the cord around the
strain relief notch.
5
Plug the AC adapter
into a standard
Wall plate
120VAC wall outlet.
6
7
Raise the antenna to a
vertical position.
Align the mounting
slots on the base. with
the mounting posts on
the wall. Push in and
down until the phone
is firmly seated.
AC adapter
AC outlet
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8
9
On the base unit, pull the
handset retainer out of the slot.
Rotate it clockwise
Handset retainer
180 degrees.
Flip the retainer from front to
back. Slide it back into the slot
so that the lip of the retainer is
up and the oval is down. The
retainer holds the handset
in place,
Direct wall plate mounting
If you don't have a standard wall plate, you can mount your phone
directly to the wall. Before doing this, consider the following:
• Avoid electrical cables, pipes, or other items behind the mounting
location, that could cause a hazard when inserting screws into
the wall.
• Try to mount your phone within 10 - 15 feet of a working phone
jack to avoid excessive cord lengths.
• Make sure the wall material is capable of supporting the weight of
the base and handset.
TOP
1
2
Insert two mounting screws
into the wall, (with their
3/16 in.
appropriate anchoring device),
3-15/16 inches apart. Allow
about 3/16 of an inch between
the wall and screwheads for
mounting the phone.
3-15/16 in.
Refer to steps 1 through 8 on
page 8 to mount the telephone.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing the battery pack
Charge the battery pack for more than 12-15 hours before you start
using your phone.
1
2
Remove the battery cover.
Connect the battery pack
connector with the correct
polarity (black and red wires),
then insert the battery pack
into the battery compartment.
Use only Uniden Battery
BT-905.
Black
Red
3
4
Slide the battery cover forward
until it snaps into place.
Place the handset on the base.
Make sure that the “status”
LED of the base unit lights, and
charging begins. Charge the
battery for at least 12-15 hours.
You can place either side up
for charging the battery.
status LED
1 0
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery use time (per charge)
From fully charged
• Seven hours coutinuous use.
• Seven days when the handset is in the standby mode.
Even when the battery
pack is not being used, it
will gradually
discharge over a long
period. For optimum
performance, be sure to
return the handset to the
base unit after a
When the battery charge becomes low
When the voltage of battery pack in the handset is very low and
needs to be charged, the phone is programmed to eliminate
functions in order to save power. If the battery charge becomes low
Battery LED blinks. If the phone is in use, the handset beeps.
Complete your conversation as quickly as possible and return the
handset to the base unit for charging.
telephone call for
charging the battery.
Cleaning the battery contacts
To maintain a good charge, it is important to clean the battery
contacts on the handset and base unit about once a month. Use a
pencil eraser or other contact cleaner.
Do not use any liquids or solvents.
Rechargeable batteries
have a memory effect that
reduces standby and talk
time. To avoid this
memory effect, on a
monthly basis, use the
phone until the Battery
lamp blinks. Then charge
the battery for 15 hours.
1 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Making a call
From the handset
talk
. The talk LED blinks.
1
2
3
Press
Dial the phone number.
To hang up, press talk or return the
handset to the base.
The phone number can be
up to 32 digits.
If the talk LED never stop
flashing, place the handset
on the base for at least
three seconds and make a
call again.
From the base
speaker
. The speaker LED
1
Press
blinks.
2
3
Dial the number on the keypad.
When you finish the call, press
speaker
to hang up.
Other Operations
To
Do this
chan
To improve reception
Press
Press
on the handset.
•
To adjust the ear speaker volume
or
during the call.
ª
/tone
To temporarily switch to tone dial Press
. The following
(When the base is set to pulse
mode)
numbers dialed will be sent as
tone dialing.
pause
Press . (Handset)
Press redial/p . (Base)
To enter a pause within dialing
sequence
1 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving a call
From the handset
Handset on the base
1
2
3
Phone rings. The talk LED flashes.
Pick up the handset and begin speaking.
talk
Press
or return the handset to the
base to finish the call.
Handset off the base
1
2
3
Phone rings. The talk LED flashes.
talk
Press
and begin speaking.
talk
To hang up, press
or return the
handset to the base.
From the base
1
The phone rings. The status LED on
the base flashes.
speaker
2
3
Press
Press
.
speaker
to finish the call.
status LED
1 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the ringer and ear speaker volume
Handset ringer tone
In the standby mode, press ringer
.
ringer
Each time
is pressed, the ringer tone setting changes and
the selected ringer tone sounds for 2 seconds.
Handset ringer switch
This switch turns the handset
ringer on or off.
ringer
of
f
o
n
ringer
of
f
o
n
Handset ear speaker volume
The phone has four ear speaker volume levels, Normal, Medium,
•
High, and Loud. Pressing
or
during a telephone call will
ª
change the ear speaker volume of the handset. This setting will
remain in effect after the telephone call has ended.
When you press
in Loud mode or press
in Normal
•
ª
mode, error sound beeps.
Base ringer switch
This switch turns the base
ringer on or off.
RINGER
OFF–ON
Base speaker volume
To control the speaker volume of the
base, adjust the
and
volume •
button as desired.
volume ª
volume
1 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Redialing a call
From the handset
The last phone number entered can be quickly redialed.
1
2
3
Press talk . The talk LED blinks.
Press redial
.
talk
Press
or place the handset on the
If the recently dialed
base to hang up.
number exceeds 32 digits,
only the first 32 digits are
retained for redialing.
From the base
speaker
. The speaker LED
1
2
3
Press
blinks.
To call the last number dialed from the
base, press redial/p .
Press speaker to finish the call.
1 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Mute
You can cut off the sound from the base or the handset
microphone.
When speaking on the handset
1
Press
during a telephone call.
mute
The sound from the microphone is
cut off.
mute
2
To cancel mute, press
or
talk
.
When speaking on the base
mute
during a telephone call.
The sound from the microphone is
cut off.
1
Press
2
To cancel mute, press mute , or
speaker
.
When the phone is ringing
mute
Press
when the phone is ringing. The ringer sound is cut
off. The ringer will sound when the next call is received.
1 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing phone numbers
Your EXA 8955 stores up to 10 numbers in handset plus 10 numbers
in the base.
From the handeset
mem
while in standby mode.
The talk LED flashes.
1
2
Press
Dial the number you wish to store (up to
20 digits)
You must press a key
within 20 seconds or the
phone will return to
standby. If you return the
handset in the cradle the
phone will return to
standby too. Press mem
and you can go to
mem
3
4
Press
Press
again.
on the keypad to select
-
0
9
the memory location where you wish to
store the number.
memory menu at any
time.
5
The talk LED goes out and the
confirmation beep indicates the number
has been stored.
From the base
memory
1
2
3
Press
.
Dial the number you wish to store.
memory
Press
Press
.
-
on the keypad to select
0
9
the memory location you wish to store
the number.
A confirmation beep indicates the
number is stored.
1 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Making calls with memory dialing
From the handset
talk
1
2
3
Press
Press
. The talk LED blinks.
mem
.
Select the memory location
) you wish to dial.
(
-
0
9
4
Press talk or return the handset to
the base to finish the call.
From the base
speaker
1
Press
blinks.
. The speaker LED
memory
2
3
Press
.
Press the number keypad
( 0
9
-
) to select the memory
location you wish to dial.
4
Press speaker to finish the call.
1 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Erasing a stored phone number
From the handset
mem
1
Press
in the standby mode.
The talk LED flashes.
2
3
Press mem again.
Enter the memory location number
(
-
9 ) on the keypad you wish to
0
delete. A confirmation beep indicates
the number has been erased.
From the base
memory
1
2
3
Press
Press
Press
.
memory
again.
0
-
9
on the keypad to select
the memory location you wish to store
the number.
A confirmation beep indicates the
number has been erased.
1 9
Download from Www.Somanuals.com. All Manuals Search And Download.
3-way conferencing
The Uniden EXA 8955 permits
3-way conversations between
the handset, base and outside
line.
Dialing from the 3-way
conversation mode is
possible only from the
handset.
When speaking on the handset
speaker
on the base to join
1
2
Press
the 3-way conversation.
Press speaker on the base to hang
up. The handset will still be
connected to the outline call.
When speaking on the base
talk
on the handset to join
the 3-way canversation.
1
2
Press
Press talk on the handset to hang
up.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your EXA 8955 intercom
Intercom from the base to handset
page/int'com
1
2
Press
The handset beeps.
on the base.
talk
Press int'c or
Speak into the mouthpiece to answer
the base.
on the handset.
talk
3
To turn off the intercom, press
on
speaker
the handset or
on the base.
Intercom from the handset to base
int'c
The base beeps.
1
2
Press
on the handset.
At the base, press page/int'com or
. Speak into the base
speaker
microphone to answer the page.
talk
on
3
To turn off the intercom, press
the handset or speaker on the base.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Transferring a call
To transfer from the handset to the base
int'c
1
Press
on the handset while
speaking on the handset. The line
will be placed on hold, and the
intercom tone will be sounded on
the base.
page/int'com
the base. The intercom mode is
activated and you may speak to the
person at the base.
2
3
Press
or
on
speaker
To complete the transfer to the base,
talk
press
on the handset.
speaker
To cancel the transfer, press
on the base.
To transfer from the base to the handset
page/int'com
on the base
1
Press
while speaking on the speaker
phone. The line will be placed on
hold, and the intercom tone will be
sounded on the handset.
int'c
2
3
Press
or
on the
talk
handset. The intercom mode is
activated and you may speak to the
person at the handset.
To complete the transfer to the
handset, press speaker on the
base.
To cancel the transfer, press
on the handset.
talk
22
Download from Www.Somanuals.com. All Manuals Search And Download.
The integrated answering device
The EXA8955 has a built-in answering system that answers and
records incoming calls.
You can also use your answering system to record a conversation,
leave a voice memo message for others who use the phone, or to
announce a special message to callers when you're away from your
phone.
Features
• Digital Tapeless Recording
• 15 minutes of Recording Time
• Selective Greetings (Outgoing Messages)
• Time and Day Stamp
• Remote Message Retrieval and Room Monitor
• Toll Saver
• Conversation Recording
Digital Tapeless Recording allows you to quickly review, save or
delete the messages. You'll never have to worry about a tape
wearing out, jamming, or resetting improperly.
The Integrated Answering System is easy and convenient to use, but
please read through all of the instructions carefully.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your answering system
Turning the answering system on/off
1
To turn the answering system on,
ans on/off
press
. A beep tone will
sound and the current greeting
message is played.
2
To turn the answering system off,
press
again.
ans on/off
Setting the clock
The clock on EXA8955 Answer System starts when power is
applied to the base. Follow these steps to set the clock to the
correct time.
1
2
Press and hold clock until a beep
tone sounds.
First, press
or
until the
correct day of the week is
announced. (Number zero through
six displays on the base as each day
Press
or
multiple times to scroll
through days, hours,
minutes, etc.
is announced.) Press
to select the day.
again
clock
3
Next, press
hear the correct hour setting.
or
until you
Numbers 1 through 12 display on
the base as each hour is announced.
Press
again to select the
clock
correct time.
If you don't set the clock
within two minutes, the
system returns to standby.
4
Press
or
until you hear the correct time setting.
Numbers 1 through 59 display on the base as each minute is
announced. Press clock again to select the correct time.
5
6
The LED displays an A or P. Press
hear the correct AM/PM setting.
or
until you
clock
Press
again to end the time/day setting. The EXA8955
announces the time that you have set.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting your greeting
When you receive a call, the answering system automatically plays
either a preset message or your own greeting.
ª
Preset Message
The following message is prerecorded:
"Hello, no one is available to take your call. Please leave a message
after the tone."
ª
Recording your personal outgoing message (Greeting)
greeting
until you hear
1
Press and hold
a long tone. Start recording your
message immediately after you hear the
long tone end.
2
When you are finished recording your
play
greeting
message, press
or
.
A long tone sounds and your message
plays back on the phone.
You can record a greeting
up to 30 second.
ª
Choosing between two outgoing messages.
greeting
message.
1
2
Press
to play the outgoing
greeting
Press
again while the
Stand within 12 inches in
front of the microphone
and speak clearly when
recording your outgoing
message.
message is played. This switches
between the two options.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the message record time
You can set your answering system to record messages up to one
or four minutes long.
One minute option:
move the REC TIME
switch to 1.
Four minutes option:
move the REC TIME
switch to 4.
REC TIME
ANN/4/1
ª
Announce only feature:
The announce only feature plays an outgoing message, but it will
not allow the caller to leave a message. Move the REC TIME
switch to the ANN position.
The message counter LED displays “ ” when system is on
standby.
Prerecorded outgoing message for Announce only feature is:
"Hello, no one is available to take your call."
Selecting a PIN code
To play your messages from a remote location, you will need to
enter a two-digit Personal Identification Number (PIN) code
(00-99). To select a PIN, perform the following steps.
pin
1
2
On the base, press and hold
button until a beep sounds and the
LED displays 00.
To set the first number, press
or
to scroll from 00 to 90.
Press
or
multiple times to scroll
through numbers on the
display.
When the desired number appears in
pin
the display, press
the first number.
. This selects
3
To set the second number, press
or to scroll from 0 to 9.
When the desired number appears in
pin
the display, press
. This selects
the second number and then the
entered number is announced.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting ring time switch
The ring time /toll saver switch
allows you to set the number of
rings the caller hears before the
answering system plays your
outgoing message. You can set
the switch to answer after two
rings or after four rings.
RING TIME
2/4/TS
In the TS (Toll Saver) position, the answering system picks up after
two rings if you have new messages, and after four rings if there are
none. This way, if you call long distance to check your messages,
you can hang up after third ring to avoid billing charges.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your answering system
Playing your message
The base LED shows the number of total messages on the
display. If the display is blinking, then there are new messages
waiting for you. The EXA 8955 is designed to play your new
messages first. After you play your new messages you can then
play your old messages.
To stop playing your
messages, press play
again.
play
. The system announces
1
Press
the number of new and old
messages, then the incoming
messages are played. The time and
day each message was received is
announced after the message is
played, and the message counter
LED displays the number of the
current message.
2
3
When all new messages have
played, a long tone is heard. The
message counter LED stops flashing
to indicate that all of the new
messages have been reviewed.
After you have reviewed all your
messages, you can play your old
play
messages again. Press
follow the instructions above.
and
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeating a message
play
to review your message.
The number of stored messages is
announces.
1
2
3
Press
Pressing
before
2.5 seconds (4.5 seconds
from remote) of the
message has played causes
the system to scan back
one message.
After a message has played for a few
seconds, press
message.
to repeat the
play
Press
at any time to stop
reviewing messages and return to
standby. The message counter LED
shows the total number of messages still
on the system.
If you have several
messages, press
until you return to the
message you want to
replay.
Skipping a message
play
to review your messages.
The number of messages is announced.
1
2
3
Press
Press
at anytime to skip to the
next message.
Each time
is
pressed, the system scans
forward one message.
Press play at any time to stop
reviewing your messages and return to
standby. The message counter LED
shows the total number of messages on
the system.
If you have several
messages, press and hold
to find the
message you want to play.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting a message
ª
Deleting individual message
play
to review your message.
1
2
Press
If you decide to delete a message,
delete
press
anytime during the
When you press delete,
you are permanently
deleting the message.
Once deleted, the message
cannot be replayed.
message. The system beeps and
immediately goes to the next
message.
3
After you have played all of your
messages, a long tone sounds on the
base speaker.
ª
Deleting all messages
delete
Press and hold
after reviewing your messages. A tone
sounds when all messages are cleared.
Voice memo
The voice memo function allows the user to record a message
(up to 10 minutes) on the base.
voice memo
1
Press and hold
,
The voice memo function
is completely independent
of the outgoing message.
It’s handy for leaving
until you hear a long beep. The
message counter LED blinks.
others a quick message.
2
3
Speak into the microphone.
When you have finished, press
voice memo
play
or
to stop
recording. The system returns to
standby.
Microphone
A voice memo message is
treated as a typical
recorded message and will
be added to the stored
messages.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a conversation
You can record up to 10 minutes of conversation while you are
making your call from the handset.
1
During the conversation from the
voice memo
handset. Press and hold
on the base. The unit begins recording
and the LED blinks. A beep that can be
heard by both parties sounds every 15
seconds.
A recorded conversation is
treated as a typical
message and will be added
to the stored messages.
2
To stop the recording, press
voice memo
play
or
.
You cannot record a conversation while you are
speaking on the base.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote access away from home
You can operate your answering system from a remote location
using any touch-tone telephone. Use this function to check for
recorded messages, to play or delete messages, even to record a
new outgoing message, and to monitor sounds in the room.
1
2
Call your telephone number.
During the answering machine is activated, press # and your
PIN code.
3
4
The answering system announces the time and day stamp
and the number of messages stored in memory. Then the
message playback automatically begins.
You must enter a
command within 15
seconds of entering
You may continue to listen to your massage, or you may
select a command from the following chart.
command waiting mode
or the answering system
automatically hangs up
and returns to standby.
Command Function
# then 1
# then 2
# then 3
# then 4
# then 5
# then 6
# then 7
# then 8
# then 9
Repeat
Playing your messages
Skipping a message
Deleting a message
Stop message playback
Answering system on
Voice memo record/stop
Outgoing message record/stop
Answer system off
Room monitor
# then
The system will only
playback messages for
four minutes and then it
returns to command
waiting mode. To continue
playing your message,
press # then 2 again
within 15 seconds
*
5
6
After all of your messages have played, or the playback time
exceeds 4 minutes, you will hear that the intermittent beeps
indicating that the system is in the command waiting mode.
You may enter another command at this time from the chart
above.
When you are finished, hang up to exit the system.
The answering system automatically returns to standby.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote room monitor
You can call your answering system from any touch-tone phone and
monitor sounds in the room where your base is installed.
1
2
Call your telephone number.
While the answering machine is activated, press # and your PIN
code.
3
4
5
The answering system begins announcing the time and day.
Press # then 5 to stop the messages.
Press # then . You hear sounds in the room where your
*
phone is installed. After 15 seconds, the answering system
returns to the command waiting mode.
6
Press # then
to monitor the room for another 15 seconds. Or
*
select another remote function. Or hang up to exit the system.
The answering system automatically returns to standby.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the digital security code
The digital security code is an identification code used to connect
the handset and the base unit. Normally, setting the code is not
necessary.
The first time you charge your handset, the security code is
automatically set. (See page 3.)
In the rare situation that you suspect another cordless telephone
is using the same security code, you can change the code.
If the handset battery pack
is completely discharged
or the battery pack
removed, the digital
security code will be lost.
If this happens, a new
security code is set
automatically the next
time the battery pack is
charged.
1
2
Remove the handset from the base
page/int'com
unit. Press
.
While the handset is producing the
page/int'com
paging sound, hold
while placing the handset in the base
unit. The paging tone stops.
Leave the handset on the base
longer than 3 seconds. A new
random security code is set.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the beltclip
To attach the beltclip
To remove the beltclip
Insert the beltclip into the holes
on each side of the handset.
Press down until it clicks.
Pull both sides of the beltclip to
release the tabs from the holes.
Headset installation
Your phone may be used with
an optional headset. To use
this feature, simply plug any
standard 2.5mm headset plug
into the headset jack. Your
phone is ready for hands-free
conversation.
headset
jack
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Note on power sources
RECYCLING NICKEL-
CADMIUM BATTERIES
Battery replacement
and handling
When the operating time
becomes short, even after a
battery is recharged, please
replace the battery.
With normal usage, your
battery should last about one
year.
NICKEL-
CADMIUM
BATTERIES
MUST BE
DISPOSED OF
PROPERLY.
Ni-Cd
Please contact your place of
purchase for a replacement
battery.
Nickel-cadmium cells are used
in the battery pack. Please
take your used nickel-
cadmium battery packs to a
store that recycles nickel-
cadmium batteries.
Power Failure
During the period that the
power is off, you will not
be able to make or receive
calls with the telephone.
Caution
• Use the specified battery pack.
• Do not remove the battery from the handset to charge it.
• Never throw the battery into a fire, disassemble it, or heat it.
• Do not remove or damage the battery casing.
Maintenance
When slightly dirty
Caution
Wipe with a soft, dry cloth.
Do not use paint thinner,
When very dirty
benzene, alcohol, or other
chemical products. Doing
so may discolor the surface
of the telephone and
Wipe with a soft cloth that has
been dampened with diluted,
neutral detergent. Dry with a
dry cloth.
damage the finish.
When the charging
terminals become dirty
Wipe with a pencil eraser or
other contact cleaner.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If your phone is not performing to your expectations, please try
these simple steps first.
Symptom
Suggestion
The status light won't
come on when the
handset is placed in
the base unit.
• Make sure the AC adapter is plugged
into the base unit and wall outlet.
• Make sure the handset is properly
seated in the base unit.
• Make sure the charging contacts on the
handset and base unit are clean.
The audio sounds
weak and/or scratchy.
• Make sure that the base unit antenna is
in a vertical position.
• Move the handset and or base unit to a
different location away from metal
objects or appliances and try again.
• Press
to help eliminate
chan
background noise.
• Make sure that you are not too far from
the base.
Can't make or receive
calls.
• Check both ends of the base unit
telephone line cord.
• Make sure the AC adapter is plugged
into the base unit and wall outlet.
• Disconnect the AC adapter for a few
minutes, then reconnect it.
• Reset the digital security code
(See page 34).
• Make sure talk is pressed.
The handset doesn't
ring or receive a page.
• The battery pack may be weak. Charge
the battery on the base unit for 12-15
hours.
• The handset may be too far away from
the base unit.
• Place the base unit away from
appliances or metal objects.
• Reset the digital security code
(See page 34).
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Suggestion
The answering system • Make sure the base unit is plugged
does not work.
in.
• Make sure that the answering system
is turned on.
Messages are
incomplete.
• The incoming messages may be too
long. Remind callers to leave a
brief message.
• The memory may be full. Delete
some or all of the saved messages.
After a power failure,
the outgoing message
is deleted.
• Record your greeting again.
The default messages should remain.
No sounds on the base • Adjust the speaker volume on the
unit speaker during call
monitoring or message
playback.
base unit.
Cannot access remote
call-in features from
another touch-tone
phone.
• Make sure you are using the correct
PIN number.
• Make sure that the touch-tone phone
you're using can transmit the tone
for at least two seconds. If it
cannnot, you may have to use
another phone to access your
message.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General
The EXA 8955 complies with FCC Parts 15 and 68.
Frequency control:
Modulation:
PLL
Frequency shift keying
Operating temperature: 0°C to +50°C (+32°F to +122°F)
Base unit
RX frequency:
TX frequency:
Power requirements:
Size:
902.119 MHz to 905.016 MHz (30 channel)
924.997 MHz to 927.894 MHz (30 channel)
9V 350mA (from AC adapter)
8-49/64 in. (W) x 6-57/64 in. (D) x 2-37/64 in. (H)
(222.5 mm (W) x 175 mm (D) x 65.3 mm (H))
Approx. 21 oz. (Approx. 594 g)
Weight:
Handset
RX frequency:
TX frequency:
Power requirements:
924.997 MHz to 927.894 MHz (30 channel)
902.119 MHz to 905.016 MHz (30 channel)
Rechargeable Nickel-Cadmium battery pack
Size (without antenna): 7 in. (W) x 2-17/64 in. (D) x 2 in. (H)
(178 mm (W) x 57.6 mm (D) x 51 mm (H))
Weight:
Battery:
Approx. 8.6 oz. (244 g) (including battery)
BT905
Capacity
Talk mode
Standby mode
600 mAH, 3.6V
7 hours TYP
7 days TYP
Specifications, features, and availability of optional
accessories are all subject to change without prior notice.
At Uniden, we’ll take care of you!
If you need any assistance with this product, please call our Customer Hotline at
1 -800-297-1 023
PLEASE DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
Our Uniden representatives will be happy to help you with any
matters regarding the operation of this unit, available accessories,
or any other related matters.
Thank you for purchasing a Uniden product.
Hours: M-F 7:00 AM to 7:00 PM CST.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Mute ......................................16
0 - 9
3-way conferencing..............20
P, Q
Package contents....................4
A
Answering device
R
Features...........................23
Setting up........................24
Using ...............................28
Receiving a call ....................13
Redialing a call .....................15
Handset ringer tone .............14
Handset ringer switch ..........14
B
Base ringer switch................14
Battery pack
S
Setting up your answering
system
Preparing and
charging ..........................10
Replacement and
handling ..........................36
Selecting a PIN code......26
Selecting the
message record time ......26
Setting the clock.............24
Setting ring time
C
Channel.................................12
Connection..............................6
switch ..............................27
Setting your greeting......25
Tuerning the answering
systen on/off...................24
Setup
D
Dialing mode ..........................7
Digital security code ........3, 34
Base unit...........................5
Handset...........................10
Specifications ........................39
E, F, G
Ear speaker volume .............14
H
T
Headset installation ..............35
Transferring a call.................22
Troubleshooting....................37
I, J, K, L
Intercom................................21
Installing the beltclip............35
U, V, W, X, Y, Z
Using your answering system
Deleting a message ........30
Playing your message ....28
Recording a
M, N, O
Maintenance..........................36
Making a call ........................12
Memory dialing
conversation ...................31
Remote access
Making a call
with memory dialing......18
Erasing a stored
phone number................19
Storing phone
away from home ............32
Remote room monitor....33
Repeating a message......29
Skipping a message .......29
Voice memo....................30
numbers ..........................17
Mounting the base unit
to a wall..................................8
40
Download from Www.Somanuals.com. All Manuals Search And Download.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|