Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Telephone Line Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Radio Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Selecting a Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Telephone Line Outlets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing the Backup Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Desk or Tabletop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Wall Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting up Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Extending the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installing the Handset Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning the Battery Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Low Battery Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Adjusting Ringer Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Using Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Two-Way Paging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Room Monitor Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Dialing a Stored Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Chain Dialing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Erasing a Stored Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
The Integrated Answering System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Answering System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Turning the Answering System On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
When using your telephone equipment, these basic safety precautions
should always be followed to reduce the risk of fire, electrical shock, and
injury to persons:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Use a dry cloth
for cleaning without liquid or aerosol cleaners.
4. Do not use this product near water; for example, near a bathtub, wash
bowl, kitchen sink or laundry tub, in a wet basement, or near a
swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The
telephone may fall, causing serious damage to the unit.
6. Slots and openings in the cabinet and the back or bottom are provided
for ventilation. To protect the product from overheating, these openings
must not be blocked or covered. This product should never be placed
near or over a radiator or heat register. This product should not be
placed in a built-in installation unless proper ventilation is provided.
7. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this
product where the cord will be damaged by persons walking on it.
9. Do not overload wall outlets and extension cords, as this can result in
the risk of fire or electric shock.
10. Never push objects of any kind into this product through cabinet slots,
as they may touch dangerous voltage points or short out parts that
could result in a risk of fire or electric shock. Never spill liquid of any
kind on the product.
11. To reduce the risk of electric shock, do not disassemble this product.
Take it to qualified service personnel when service or repair work is
required. Opening or removing covers may expose you to dangerous
voltages or other risks. Incorrect reassembly can cause electric shock
when the appliance is subsequently used.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
A. When the power supply cord is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when following the
operating instructions. (Adjust only those controls that are covered
by the operating instructions. Improper adjustment of other controls
may result in damage and will often require extensive repair work
by a qualified technician.)
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
13. Do not use the telephone to report a gas leak in the vicinity of the leak.
Caution:
To reduce the risk of fire or injury to persons by the battery, read
and follow these instructions.
1. Use only the appropriate type and size Battery Pack specified in this
Operating Guide.
2. Do not dispose of the Battery Pack in a fire. The cell may explode.
Check the Nickel-Cadmium Battery Disposal package insert for
disposal instructions.
3. Do not open or mutilate the Battery Pack. Released electrolyte is
corrosive and may cause damage to the eyes or skin. It may be toxic if
swallowed.
4. Exercise care in handling the battery in order not to short the battery
with conducting materials such as rings, bracelets, and keys. The
battery or conductor may overheat and cause burns.
5. Charge the Battery Pack provided with or identified for use with this
product only in accordance with the instructions and limitations
specified in the instruction manual provided for this product.
6. Observe proper polarity orientation between the Battery Pack and
battery charger.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Congratulations on your purchase of a Uniden XCA4500 Integrated
Telephone Answering Device. Your new telephone answering device is
designed to exacting standards to provide reliability, long life, and
outstanding performance.
Features
•
•
•
•
•
•
•
25 44/49 MHz Channels
Random Code™ Digital Security
UltraClear Plus
AutoTalk™
10 Number Memory
•
•
•
•
•
•
•
Integrated Answering System
AutoSecure™
Pulse/Tone Dialing
AutoStandby™
2 One-Touch Dialing Buttons
Two-Way Page/Intercom
Handset Ringer/Volume Controls
Redial/Pause and Flash
Reversible Handset Retainer
The XCA4500 has a built-in telephone Answering System so you’ll never
miss another important call. Unlike other Answering Systems, you can
perform all of the functions using either your Handset or Base Unit, including
recording a new outgoing message, monitoring incoming calls, and playing
and deleting your messages.
AutoTalk™ allows you to answer a call by just removing the Handset from
the Base, so you don’t have to waste time pushing buttons or flipping
switches. AutoStandby™ allows you to hang up by simply returning the
Handset to the Base.
The UltraClear Plus true compander circuitry virtually eliminates background
noise, and the 25 Channel Auto-Scan monitors multiple channels and
automatically selects the best channel to assure crystal clear transmissions.
Together, these innovations give you the best possible reception during all
your conversations.
To protect you against misbilled calls which might result from your phone
being activated by other equipment, the XCA4500 has Random Code™
digital security which automatically selects one of over 65 thousand digital
security codes for the Handset and Base Unit. Also, the AutoSecure™
feature electronically locks your phone when the Handset is in the Base.
To get the most from your phone, please read this Operating Guide
thoroughly. Also be sure to complete the Product Registration Form and mail
it in.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Included with Your XCA4500
If any of these items are missing or damaged, do not contact the place of
purchase. Instead contact Uniden Customer Service at: (800) 297-1023,
8:00 a.m. to 5:00 p.m., Central, Monday through Friday.
Handset
Base Unit
AC Adapter
Long Telephone
Cord
Rechargeable
Handset Battery
Short Telephone
Cord
Operating Guide
9V Backup Battery
Other Printed
Material
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Electrical Considerations
Unplug all electrical appliances when you know an electrical storm is
approaching. Lightning can pass through your household wiring and damage
any device connected to it. This unit is no exception.
Warning: Please do not attempt to unplug any appliance during an
electrical storm.
Caution:
Changes or modifications to this product not expressly approved
by Uniden, or operation of this product in any way other than
as detailed by this Operating Guide, could void your authority
to operate this product.
Range
This unit is designed to achieve the maximum possible range by transmitting
and receiving according to the highest specifications set forth by the I.C. We
have rated this phone to operate at a maximum distance with the
qualification that the range depends upon the environment in which the
telephone is used. Many factors limit range, and it would be impossible to
include all the variables in our rating. The Maximum Range rating of your
integrated telephone answering device is meant to be used as a means of
comparison against other range claims.
Telephone Line Problems
The FCC has granted the telephone company the right to disconnect service
in the event that your phone causes problems on the telephone line. Also,
the telephone company may make changes in facilities and services which
may affect the operation of your unit. However, your telephone company
must give adequate notice in writing prior to such actions to allow you time
for making necessary arrangements to continue uninterrupted service.
If you are having trouble with your telephone service, you must first
disconnect your phone to determine if it is the cause of your problem. If you
determine that it is the cause, you must leave it disconnected until the
trouble has been corrected.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio Interference
Radio interference may occasionally cause buzzing and humming in your
cordless Handset or clicking noises in the Base Unit. This interference is
caused by external sources such as TV, refrigerator, vacuum cleaner,
fluorescent lighting, or electrical storms. Your unit is NOT DEFECTIVE. If
these noises continue and are too distracting, please check around your
home to see what appliances may be causing the problem. In addition, we
recommend that the Base Unit not be plugged into a circuit that also powers
a major appliance because of the potential for interference. Be certain that
the antenna on the unit is fully extended when needed.
In the unlikely event that you consistently hear other voices or distracting
transmissions on your phone, you may be receiving radio signals from
another cordless telephone or other source of interference. If you cannot
eliminate this type of interference, you need to change to a different channel.
Finally, it should be noted that some cordless telephones operate at
frequencies that may cause interference to nearby TVs and VCRs; to
minimize or prevent such interference, the base of the cordless telephone
should not be placed near or on top of a TV or VCR; and, if interference is
experienced, moving the cordless telephone farther away from the TV or
VCR will often reduce or eliminate the interference.
More Than One Cordless Telephone
If you want to use more than one cordless telephone in your home, they
must operate on different channels. Press the channel key to select a
channel that provides the clearest communication.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Selecting a Location
Before choosing a location for your XCA4500, there are some important
guidelines you should consider:
•
The location should be close to both a phone jack and continuous
power outlet. (A continuous power outlet is an AC outlet which does
not have a switch to interrupt its power.)
•
•
•
•
Keep the Base Unit and Handset away from sources of electrical
noise such as motors or fluorescent lighting.
Be sure there is sufficient space to fully extend the Base Unit
antenna.
The Base Unit can be placed on a desk or tabletop or mounted on a
standard AT&T or GTE wall plate.
If you decide to mount your integrated telephone answering device
on the wall, make sure to change the handset retainer so that the
tab which holds the Handset faces up. (See page 20 for more
information.)
•
You should charge your new phone for 15-20 hours before
completing the installation or using the Handset.
Telephone Line Outlets
There are two types of phone outlets:
Modular Jack
Most phone equipment available now uses modular jacks. Phone
cords are fitted with a molded plastic connector which plugs into
this type of jack. If you do not have modular phone jacks, contact
your local telephone company for information about their
installation.
Hard-wired Jack
Some equipment is wired directly to a phone jack, and these types
of installations require a modular jack converter. This type of
installation is not difficult; however, you should contact your Uniden
telephone dealer or a telephone supply store for advice about the
proper adapter or converter for your particular situation.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Telephone Cords
Consider these safety guidelines before connecting the telephone cords:
CAUTION:
•
•
Never install telephone wiring during a lightning storm.
Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected.
•
Use caution when installing or modifying telephone lines.
Applying Power to the Base Unit
The XCA4500 requires a standard electrical outlet (120 volts AC without a
switch to interrupt power) and the included AC adapter. Connect the adapter
as shown below.
1. Wrap the power cord around
the convenient notch on the
bottom.
Important: Place the power
cord so that it does not create
a trip hazard, or where it
could become chafed and
create a fire or other electrical
hazards.
2. When power is first applied,
the Message Counter LED
display flashes P quickly
while the system’s memory
initializes. When the flashing
slows, press the STOP button
on the Base Unit.
Digital Answering Syste
NEW MESSAGE
STOP
P
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO INTERCOM
DELETE
PAGE/FIND
3. The Message Counter LED
display turns off, and the time
and remaining message
Digital Answering System
NEW MESSAGE
STOP
REPEAT
PLAY
SKIP
record time are announced.
Note: For information about
turning the Answering
System On/Off, see page 46.
ANS ON/OFF
OGM
MEMO INTERCOM
PAGE/FIND
DELETE
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Backup Battery
In the event of a power outage, your phone has a 9-volt battery backup
which can prevent the loss of your messages for up to four hours.
1. Press down and away from
the Base to remove the cover.
2. Place the battery in the
compartment.
Note: Make sure that the
positive battery terminal
touches the left contact.
3. Replace the battery cover.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Plug one end of the long
telephone cord into the TEL LINE
jack on the Base Unit.
5. Plug the other end of the cord
into the telephone jack on the
wall.
6. Plug the AC Adapter into a
standard 120V AC wall outlet.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement of the Handset
The unique design of your phone allows you to place the Handset on the
Base Unit either face down or in an upright position. The battery charges in
either position.
:
P
A
GE/FIND
Upright Position for
Handset
Facedown Position for
Handset
Wall Installation
Standard Wall Plate Mounting
The XCA4500 is designed to be mounted on a standard AT&T or GTE wall
plate.
1. Plug the AC Adapter into the
Base Unit.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Place the AC Adapter cord
inside the molded channel.
3. Plug one end of the short
telephone cord into the TEL LINE
jack on the Base Unit.
4. Place the telephone cord inside
the molded channel on the
bottom of the Base Unit.
Then plug the other end of the
telephone cord into the modular
jack on the wall.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Place the Base Unit on the
posts of the wall plate and push
down until it’s firmly seated.
6. Plug the AC Adapter into a
standard 120V AC wall outlet.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Wall Mounting
If you do not have a standard wall plate, you can mount the XCA4500
directly on a wall. Before mounting your integrated telephone answering
device, consider the following:
•
Select a location away from electrical cables, pipes, or other items
behind the mounting location that could cause a hazard when
inserting screws into the wall.
•
•
Make sure the wall material is capable of supporting the weight of
the Base Unit and Handset.
Use #10 screws with anchoring devices suitable for the wall
material where the Base Unit will be placed.
1/5 IN.
1. Insert two mounting screws
315
⁄16 inches apart. Allow about
1
⁄
5 of an inch between the wall
and screw heads for mounting
the phone.
3 15/16 IN.
2. Plug the AC Adapter into the
Base Unit.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Place the AC Adapter cord
inside the molded channel.
4. Plug one end of the long
telephone cord into the
TEL LINE jack on the Base
Unit.
5. Place the cord inside the
molded channel on the
bottom of the Base Unit.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Place the Base Unit on the
screws and push down until
it’s firmly seated.
7. Plug the other end of the
telephone line cord into the
wall jack.
8. Plug the AC Adapter into a
standard 120V AC wall outlet.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Handset Retainer
The Handset Retainer holds the Handset in place if your phone is mounted
on a wall. These steps describe how to remove and replace the retainer so
that the tab faces up.
1. Push up on the Handset
Retainer on the Base Unit,
and slide the tab out.
2. Flip the Retainer over so the
tab faces up.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Put the Retainer back into
its slot on the Base Unit.
4. Push down on the Handset
Retainer until it snaps into
place.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up Your Phone
Extending the Antenna
Before using your phone, be
sure to raise its Antenna to
the vertical position, and then
extend the Antenna.
RING SW PULSE-TONE CPC
2-5-TS OFF-ON
REC TIME RING VOL
ANN-1 OFF-LO-HI
RESET
DC IN 9V
TEL-LINE
+
-
Installing the Handset Battery Pack
1. Press in on the Battery Cover
Release.
NOTE
R
D
B
22
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Slide the Battery
Compartment cover down.
3. Align the plastic connector of
the Nickel-Cadmium Battery
Pack with its socket and plug
it in.
Warning: Always install
Battery Cable with Black Wire
closest to the left.
WARNING !
Always Install Battery Cable
with Black Wire closest to
the left
4. Place the Battery Pack inside
the Battery Compartment,
and slide the battery cover
back on.
Note: The built-in Memory Backup feature allows up to 3 minutes to
disconnect the old battery pack and install a new one without losing
any phone numbers that may be stored in the telephone’s memory.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Battery Contacts
To maintain a good charge, it is important to clean all charging contacts on
the Handset and Base Unit about once a month. Use a pencil eraser or other
contact cleaner. Do not use any liquids or solvents.
Contacts
®
REMOTE
TALK
CHANNEL
ULTRACLEAR
PLUS
TALK
BATT LOW
1
2
1
3
9
ABC
DEF
1
2
3
6
7
GHI
JKL
MNO
4
5
6
8
4
Digital Answering System
PRS
TUV
WXY
NEW MESSAGE
STOP
7
8
9
8
?
&
0
OPR
#
0
IN USE
BATTERY
CHARGE
REPEAT
PLAY
SKIP
*
TONE
MEM
1
2
CHAN
FLASH VOLUME
R. TONE R. VOL
INT'C
RDL/P
ANS ON/OFF OGM
MEMO INTERCOM
DELETE
Extend•A•Phone
SERIES
POWER
H
Q
MIC
PAGE/FIND
Contacts (On Bottom)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Charging the Handset Battery Pack
Initial Battery Charging
The rechargeable Nickel-Cadmium battery pack must be fully charged
before using your phone for the first time. We recommend that the battery
pack charge for approximately 15-20 hours, without interruption, before
plugging the phone line into your new phone.
1.
Place the Handset on the
Base Unit. Depending on
your installation, you can
charge the Handset in the
upright position.
:
—OR—
You can charge the Handset
in its facedown position.
P
A
GE/FIND
25
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Make sure the CHARGE LED
lights. If the LED doesn’t light,
check to see that the AC
NEW MESSAGE
STOP
IN USE
BATTERY
CHARGE
REPEAT
Adapter is plugged in and
that the Handset is making
good contact with the Base
Unit charging contacts.
ANS ON/OFF
DELETE
POWER
Continuous Battery Charging
For the best battery performance, return the Handset to the Base Unit at the
end of the day to keep the battery fully charged.
Low Battery Indicator
When the Battery Pack in the
REMOTE
TALK
TALK
Handset is very low and
needs to be charged, the
BATT LOW
1
2
1
3
9
TALK/BATT LOW LED flashes.
ABC
DEF
1
2
3
7
GHI
JKL
MNO
4
5
6
4
PRS
TUV
WXY
7
8
9
If the TALK/BATT LOW LED begins to flash, the phone is programmed to
eliminate its functions to save power. The table below describes what to do
to return your phone to normal operation.
During a Call
In Standby Mode
Only the T button operates.
None of the buttons will operate.
The Handset beeps and the
TALK/BATT LOW LED flashes once
every three seconds.
The Handset TALK/BATT LOW LED
flashes once every three seconds.
Complete your call as quickly as
possible.
You will not be able to make a call.
Return the Handset to the Base
Unit for charging.
Return the Handset to the Base
Unit for charging.
Note: Allow 15 to 20 hours without interruption for the Handset to fully
recharge.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Pulse/Tone Switch
Be sure the PULSE/TONE switch is in the TONE position if you have touch-tone
telephone service.
PULSE-TONE
RING SW PULSE-TONE CPC
2-5-TS OFF-ON
REC TIME RING VOL
ANN-1 OFF-LO-HI
RESET
DC IN 9V
TEL-LINE
+
-
Note: Most phone systems are Tone dialing. Check with your local phone
company if you are not sure whether your system is Tone or Pulse
dialing.
Adjusting Ringer Controls
Handset Volume Controls
8
?
To adjust the ringer volume of
your Handset, press L
when the phone is not in use.
&
OPR
0
TONE
MEM
1
2
CHAN
FLASH
R. TONE
VOLUME
R. VOL
INT'C
/P
Handset Ringer
Volume Control
8
?
You can also select one of
two different ringer tones for
the Handset.
&
OPR
0
TONE
MEM
1
2
CHAN
When the phone is not in use,
press O to select a
different ringer tone.
FLASH
R. TONE
VOLUME
R. VOL
INT'C
RDL/P
Handset Ringer Tone
Select Key
27
Download from Www.Somanuals.com. All Manuals Search And Download.
To adjust the receiver
volume, press V while
you are on a call.
8
?
&
OPR
0
TONE
MEM
1
2
CHAN
FLASH
R. TONE
VOLUME
R. VOL
INT'C
/P
Handset Receiver
Volume Control
Base Volume Controls
To adjust the Base Unit ringer volume, move the RING-OFF LO HI switch
to the desired setting.
RING VOL
OFF-LO-HI
RING SW PULSE-TONE CPC
2-5-TS OFF-ON
REC TIME RING VOL
ANN-1 OFF-LO-HI
RESET
DC IN 9V
TEL-LINE
+
-
To adjust the Base speaker volume, slide the VOLUME control to the
desired setting.
VOLUME
VOLUM
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic Digital Code Security
Many cordless telephones operate similarly and on the same frequency.
Without digital code security, another Handset could make calls using your
Base Unit and telephone line. To avoid unauthorized calls on your phone, a
Digital Code feature was added to the XCA4500. This Digital Code is
shared only between the Handset and Base Unit. The Code is set
automatically when you first use the phone.
To reset the Digital Code, be sure the Handset is on the Base, then:
1. Press INTERCOM on the Base
Unit.
Digital Answering System
NEW MESSAGE
STOP
0
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO INTERCOM
DELETE
PAGE/FIND
2. Remove the Handset from
the Base Unit, and then set it
down again.
:
29
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The CHARGE LED will blink to
indicate that the Digital
NEW MESSAGE
STOP
Security Code is set to one of
more than 65,000 codes.
IN USE
BATTERY
CHARGE
REPEAT
ANS ON/OFF
DELETE
POWER
If the Base Unit loses power while the Handset is off the Base, the Digital
Code may be erased. When this happens, the Handset will not function. To
establish communication between the Handset and Base Unit:
1. Restore power to the Base
Unit, and place the Handset
back on the Base Unit.
2. The CHARGE LED will blink to
NEW MESSAGE
indicate that the Digital
Security Code is set.
IN USE
REPEAT
STOP
BATTERY
CHARGE
ANS ON/OFF
DELETE
POWER
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Phone
Making and Receiving Calls
The following features of your XCA4500 phone are different depending on
the Handset’s location when you make or receive a call.
HANDSET ON
BASE
HANDSET OFF
BASE
ANSWER Pick up Handset
PressT .
CALL
(AutoTalk).
1) Pick up Handset.
1) PressT .
2) Listen for dial tone.
3) Dial the number.
MAKE
CALL
2) PressT .
3)
Listen for dial tone.
4) Dial the number.
PressT .
HANG
UP
— OR —
Return Handset to Base
(AutoStandby).
1)
Pick up Handset.
1)
PressT .
REDIAL
2) PressT .
2) Listen for dial tone.
3) Listen for dial tone.
4)
3) PressR .
PressR
Note: Sometimes when you press T to hang up the phone, you may get
an error tone and the phone will not disconnect. If this happens,
place the Handset on the Base Unit or press T again while
holding the Handset close to the Base Unit.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Channels, Flash, and Page/Find
To change channels or access Call Waiting while the phone is in use, or to
use the one-way page to locate the Handset, follow these steps:
PRESS THESE KEYS
YOU WILL HEAR
Press E .
A click similar to when
F is pressed. There
may be a brief pause as
your phone searches for a
clear channel.
CHANGING
CHANNELS
Note: Change channels to
help eliminate background
noise.
If the Call Waiting tone
sounds, pressF to
accept the waiting call.
A click, a short pause, then
the caller (if you were on a
call).
FLASH
— OR —
— OR —
If you have finished a call
and want to make another
call, pressF to hang
up and get a dial tone.
A click, and then a dial tone
so you can make a different
call.
Press PAGE/FIND on the
Base Unit to locate or page beep.
the Handset.
The Handset will begin to
PAGE/FIND
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Two-Way Intercom
The Two-Way Page/Intercom feature allows you to communicate between
the Base Unit and the Handset. To use this feature:
•
•
The RING ON/BATT SAVE Switch on the Handset must be in the
RING ON position.
The BASE UNIT RINGER Switch must be set to either LO or HI
.
Note: If you are on a call while using the Handset and you page the Base
Unit, the Base Unit will ring even when the Base Ringer Switch is set
to the OFF position.
Two-Way Paging
Paging the Base Unit
1. Press J on
the Handset.
Note: If there is no
answer, press
J again to
cancel.
3
2. Press INTERCOM on
the Base Unit to
:
answer page.
The IN USE and
1
TALK/BATT LOW
LEDs light.
2,3
To end the
conversation:
3. Press T on
the Handset or
INTERCOM on the
Base.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Paging the Handset
1. Press INTERCOM on
the Base Unit.
Note: If there is no
answer, press
INTERCOM again to
cancel.
2,3
2
2. Press T or
J on the
Handset to answer
the page.
:
The IN USE and
TALK/BATT LOW
LEDs light.
1,3
To end the
conversation:
3. Press INTERCOM on
the Base Unit, or
T the Handset.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Room Monitor Feature
Another use of the XCA4500 is to monitor activity near the Base Unit. To
turn the monitor on, follow the steps below.
1. Press J on the Handset.
2. Press T on the Handset.
Note: Using the Handset, you
should now be able
to monitor the room where
the Base Unit is located.
To turn the monitor off:
3. Press T on the Handset.
2,3
:
1
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Your Phone
All programming functions must be completed when your phone is in the Standby
mode. The programming keys will not function while you are on the phone.
Storing a Number in Memory
Use these keys
to store a
number in
memory.
REMOTE
TALK
TALK
BATT LOW
1
2
1
ABC
DEF
1
2
3
7
3
Note: An error
tone will sound
and the
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
programming
procedure will be
canceled if more
than 20 seconds
elapse between
each keystroke
entry or step.
7
8
9
8
?
OPR
0
TONE
MEM
1
2
CHAN
VOLUME
R. VOL
INT'C
R. TONE
RDL/P
1. Remove the Handset from
the Base Unit.
2. PressM .
8
?
OPR
The TALK/BATT LOW LED
blinks.
0
TONE
MEM
CHAN
RDL/P
1
2
FLASH VOLUME
R. TONE R. VOL
INT'C
3. Enter the number you want to
store (up to 16 digits).
5551212
36
Download from Www.Somanuals.com. All Manuals Search And Download.
4. If a pause is needed during
dialing to access a long
distance service, press
R .
9R5551212
Note: The R button counts as one digit. Pressing R more than
once increases the length of the pause between numbers.
5. PressM again.
6. Enter the memory location
(0-9).
A tone indicates that the
number is stored.
REMO
TE
1
2
6
1
7
4
3
8
5
?
&
INT'C
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Mixed Number with a Pulse System
If your phone is set up for pulse dialing, you can store a mixed mode number
so that you can easily access long distance services.
Use these keys
REMOTE
TALK
TALK
to store a mixed
mode number in
memory.
BATT LOW
1
2
1
3
9
ABC
DEF
1
2
3
7
Note: An error
tone will sound
and the
GHI
JKL
MNO
4
5
6
4
PRS
TUV
WXY
programming
procedure will be
canceled if more
than 20 seconds
elapse between
each keystroke
entry or step.
7
8
9
8
?
OPR
0
TONE
MEM
1
2
CHAN
VOLUME
R. VOL
INT'C
R. TONE
RDL/P
1. Remove the Handset from
the Base Unit.
2. Press M .
8
?
OPR
The TALK/BATT LOW LED
blinks.
0
TONE
CHAN
RDL/P
MEM
1
2
FLASH VOLUME
R. TONE R. VOL
INT'C
3. Enter the number to be dialed
in pulse mode.
5551212
38
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press TONE on the Handset.
9
4
PRS
TUV
WXY
7
8
9
8
?
OPR
0
TONE
MEM
CHAN
RDL/P
1
2
FLASH VOLUME
R. TONE R. VOL
INT'C
5. Enter the number to be dialed
in Tone mode.
3300
R 3300
6. If a pause is needed during
dialing to access a long
distance service, press
R .
Note: The R button counts as one digit. Pressing R more than
once increases the length of the pause between numbers.
7. Press M again.
8. Enter the memory location
(0-9).
A tone indicates that the
number is stored.
REMO
TE
1
2
6
1
7
4
3
8
5
?
&
INT'C
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing One-Touch Dialing Numbers
Use these keys
REMOTE
TALK
TALK
to store a
BATT LOW
number in a
One-Touch
dialing button.
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
Note: An error
tone will sound
and the
programming
procedure will be
canceled if more
than 20 seconds
elapse between
each keystroke
9
4
PRS
TUV
WXY
7
8
9
8
?
OPR
0
TONE
MEM
1
2
CHAN
VOLUME
R. VOL
INT'C
R. TONE
RDL/P
1. Remove the Handset from
the Base Unit.
2. Press M .
The TALK/BATT LOW LED
blinks.
8
?
OPR
0
TONE
CHAN
RDL/P
MEM
1
2
FLASH VOLUME
R. TONE R. VOL
INT'C
3. Enter the number you want to
store (up to 16 digits).
5551212
R5551212
4. If a pause is needed during
dialing to access a long
distance service, press
R .
9
Note: The R button counts as one digit. Pressing R more than
once increases the length of the pause between numbers.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Now press the One-Touch
Dialing button ( or ) you
want to program.
1
2
A tone indicates that the
number is stored.
REMO
TE
1
2
6
1
7
4
3
8
5
?
&
INT'C
Dialing a Stored Number
To dial a number previously stored in memory, follow these steps:
MEMORY DIALING ONE-TOUCH DIALING KEYS
Remove the Handset from the Base Remove the Handset from the Base
Unit.
Unit.
Press T .
Press M .
Press T .
Press the One-Touch Dialing button
where the number is stored.
Press the memory location number
(0-9).
Chain Dialing
On certain occasions, after dialing a number, you may be requested by the
party or service you are calling to enter a special access code, such as when
performing a banking transaction. To do this, simply:
1. Store the access code into one of the memory locations.
2. Dial the main number.
3. At the appropriate time, press M followed by the memory location
number or One-Touch Dialing button where the access code is saved.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Erasing a Stored Number
To erase a number previously stored in a memory location (0-9) or in
One-Touch memory, follow these steps:
MEMORY
ONE-TOUCH KEYS
Remove the Handset from the Base Remove the Handset from the Base
Unit.
Unit.
Press M twice.
Press M twice.
Press the memory location number
(0-9).
Press the One-Touch Dialing button
you want to clear.
Note: An error tone will sound and the erase procedure will be canceled if
more than 20 seconds elapse between each keystroke entry or step.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
The Integrated Answering System
The XCA4500 has a built-in Answering System which answers incoming
calls and records your messages. You can also use your new Answering
System to record a conversation, leave a memo message for someone else
who will use the phone, or to announce a special message when you’ll be
away from your phone.
Features
•
•
•
•
•
Digital Tapeless Recording
Remote Operation from Handset
Selectable Outgoing Messages
Voice-Guided Help Menu
Time and Day Stamp
•
•
•
•
•
More than 12 Minutes Record Time
Call Screening
Calling Party Control
Battery Memory Backup
Toll Saver
Digital Tapeless Recording allows you to quickly review your messages,
saving or deleting the messages you choose. You’ll never have to worry
about a tape wearing out or resetting properly.
There is also a Voice-Guided Help Menu available when operating the
remote keys from the Handset. By simply pressing one button, you can
review all of the function keys on the Handset. You won’t have to worry
about finding a quick reference card because help is really at your fingertips.
Your XCA4500 is an advanced, integrated system which offers you
maximum flexibility, but please read through the sections that explain all of
the features before using your Answering System.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering System Setup
Turning the Answering System On/Off
Handset Operation
1. To turn the Answering
REMOTE
TALK
, press r
System ON
.
TALK
BATT LOW
1
The TALK/BATT LOW LED
lights orange. The current
Time and Day Stamp and
number of messages
2
1
ABC
DEF
1
2
3
7
3
recorded is announced in the
GHI
JKL
MNO
Handset receiver.
4
5
6
9
4
PRS
TUV
WXY
7
8
9
5
2. Press
REMOTE
TALK
TALK
You will hear a tone
BATT LOW
in the Handset followed
by the announcement:
“Answering System on.”
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
Press r
3.
again to
return to Standby.
The TALK/BATT LOW LED
turns off.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
4. To turn the Answering
REMOTE
TALK
, press r
System OFF
.
TALK
BATT LOW
1
The TALK/BATT LOW LED
lights orange. The current
Time and Day Stamp and
number of messages
2
1
ABC
DEF
1
2
3
7
3
recorded is announced on the
Handset receiver.
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
5
5.
Press
REMOTE
TALK
TALK
You will hear a tone in the
Handset followed by the
announcement: “Answering
System off.”
BATT LOW
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
Press r
6.
again to
return to Standby.
The TALK/BATT LOW LED
turns off.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Operation
1. To turn the Answering
Digital Answering System
NEW MESSAGE
STOP
System ON, press
ANS ON/OFF
.
0
REPEAT
PLAY
SKIP
A tone sounds, and the
current outgoing message
plays on the Base Unit
speaker. A second tone
sounds to indicate the unit is
ready to answer calls, and
the Message Counter LED
turns on.
ANS ON/OFF
OG
MEMO INTERCOM
DELETE
PAGE/FIND
2. To turn the Answering
System OFF, press
ANS ON/OFF again.
A tone sounds and the
Message Counter LED turns
off.
Setting the Clock
The clock in your xca4500 Answering System starts when power is applied to
the Base Unit. Follow these steps to set the clock to the correct time.
Press r
1.
on the
REMOTE
TALK
Handset.
TALK
BATT LOW
1
The TALK/BATT LOW LED
2
1
lights orange.
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
46
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press
*
Then enter the number which
corresponds to the day.
3. Enter the two-digit number for
the hour (01-12) and the
minute (00-59).
4. To set a.m., press
To set p.m., press
*
#
Note: A beep indicates the
new time is programmed, and
the new Time and Day Stamp
is announced in the Handset
receiver.
Press r
5.
to return to
Standby.
6. For example, to set Tuesday
at 3:20 p.m., press r
*30320#
followed by these keys.
Note: Remember to press
r
again to return to
Standby.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Reviewing Time and Day Stamp
Handset Operation
Press r
The Handset beeps and the
Time and Day Stamp is
announced, followed by the
total number of messages
stored in memory. The
TALK/BATT LOW LED lights
orange.
1.
to hear the
current Time and Day Stamp.
REMOTE
TALK
TALK
BATT LOW
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
6
2. Press
to replay the current
REMOTE
TALK
Time and Day Stamp while
using the remote keys .
TALK
BATT LOW
1
2
1
The Handset beeps and the
Time and Day Stamp is
replayed, followed by the
remaining recording time
available for new messages.
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
Press r
3.
again to
return to Standby.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Operation
1. Press STOP
.
Digital Answering System
NEW MESSAGE
STOP
The speaker beeps, and the
Time and Day Stamp is
announced followed by the
remaining recording time
available.
0
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO INTERCOM
DELETE
PAGE/FIND
Setting Your Outgoing Message (OGM)
When you receive a call, the Answering System answers and automatically
plays either a preset message or your personal OGM
.
Preset Messages
The XCA4500 has two messages programmed in its memory. If the
REC TIME/ANN-1 switch is in the right position, the first preset message below
plays, and all incoming messages are limited to one minute. If the switch is
set in the left position, (i.e., the “Announce Only” position) the second
message below plays, and no incoming messages are recorded.
•
•
Hello. No one is available to take your call. Please leave your
message after the tone.
Hello. No one is available to take your call.
REC TIME
ANN-1
RING SW PULSE-TONE CPC
2-5-TS OFF-ON
REC TIME RING VOL
ANN-1 OFF-LO-HI
RESET
DC IN 9V
TEL-LINE
+
-
Note: If the REC TIME/ANN-1 switch is in the “Announce Only” position, the
Message Counter LED displays an when the system is in Standby.
A
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Personal OGM
Handset Operation
Press r
1.
.
REMOTE
TALK
TALK
The TALK/BATT LOW LED
BATT LOW
1
lights orange.
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
7
2. Press
.
REMOTE
TALK
TALK
Note: You can leave up to a
60-second outgoing message.
BATT LOW
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Press 6to stop recording.
3.
REMOTE
TALK
TALK
The message replays in the
Handset receiver.
BATT LOW
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
Press r
4.
again to return
to Standby.
The TALK/BATT LOW LED
turns off.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Operation
1. To record an outgoing
message, press and hold the
OGM Button.
Digital Answering System
NEW MESSAGE
STOP
0
REPEAT
PLAY
SKIP
Start recording your message
after you hear the long tone
and the Message Counter
LED begins to count up.
ANS ON/OFF
OGM
MEO INTERCOM
DELETE
Press and
Hold
PAGE/FIND
2. Do not get closer than
12 inches from the
microphone, and speak
clearly while recording your
message. When you are
finished recording, release
the OGM Button.
You hear a tone, and your
message is played on the
Base Unit speaker. The
Message Counter LED resets
to zero.
Note: You can leave up to a
60-second outgoing message.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Preset OGM
After you have recorded an outgoing message, you can set your Answering
System to play either a preset message or your outgoing message.
1. Press OGM
.
Digital Answering System
NEW MESSAGE
Your recorded outgoing
message will begin to play.
0
REPEAT
PLAY
SKIP
STOP
ANS ON/OFF
OGM
MEINTERCOM
DELETE
PAGE/FIND
2. While your recorded outgoing message is playing, press OGM again.
A tone will sound, and you hear the preset message “Hello. No one is
available to take your call, please leave your message after the tone”
on the Base Unit speaker. A second tone sounds after the preset
message plays, and the Answering System automatically returns to
Standby.
Note: If the REC TIME/ANN-1 switch is set to Announce Only, then the
preset message “Hello. No one is available to take your call” is played.
3. To select your recorded
Digital Answering System
NEW MESSAGE
message again, press OGM
.
0
The preset message will
begin to play on the Base
Unit speaker.
REPEAT
PLAY
SKIP
STOP
ANS ON/OFF
OGM
MEINTERCOM
DELETE
PAGE/FIND
4. While the preset message is playing, press OGM again.
A tone will sound, and your recorded message will play on the Base
Unit speaker. A second tone sounds after your message plays, and the
Answering System automatically returns to Standby.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Calling Party Control Switch
The Calling Party Control (CPC) switch sets your Answering System to
disconnect and reset if the caller hangs up before leaving a message. This
prevents your Answering System from using recording time to record a hang
up/dial tone message.
Note: It is possible that if someone calls while your outgoing message is
playing or when a message is being recorded and you have Call
Waiting, that the Answering System will disconnect and reset. To
prevent this you can set the CPC switch to off.
CPC
OFF-ON
RING SW PULSE-TONE CPC
2-5-TS OFF-ON
REC TIME RING VOL
ANN-1 OFF-LO-HI
RESET
DC IN 9V
TEL-LINE
+
-
Setting the Toll Saver Switch
The Ring Number/Toll Saver switch allows you to set the number of rings the
caller hears before your Answering System answers. You can set the switch
to answer after
2
rings or after
5
rings. In the TS (Toll Saver) position, the
Answering System answers after two rings if you have messages recorded,
and it answers after five rings if there are no messages. So if you call long
distance to check your messages, you can hang up after the second ring
and not be billed.
RING SW
2-5-TS
RING SW PULSE-TONE CPC
2-5-TS OFF-ON
REC TIME RING VOL
ANN-1 OFF-LO-HI
RESET
DC IN 9V
TEL-LINE
+
-
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Reset Button
The RESET button is used to erase all recorded outgoing messages and any
messages which are saved in memory. Pressing RESET does not erase your
PIN (Personal Identification Number) code or the security code between the
Handset and Base Unit.
RESET
RING SW PULSE-TONE CPC
2-5-TS OFF-ON
REC TIME RING VOL
ANN-1 OFF-LO-HI
RESET
DC IN 9V
TEL-LINE
+
-
When RESET is pressed, the Message Counter
begins to flash. See page 10, “Applying Power to
the Base Unit,” for instructions on returning the
system to Standby.
Note: The RESET button may also be used in the unlikely event that an AC
power line disturbance causes the answering system to
malfunction and become inoperative.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Answering System
Playing New Messages
Handset Operation
Press r
1.
.
REMOTE
TALK
TALK
The current Time and Day
Stamp and number of stored
messages is announced.
BATT LOW
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
2. Press
8
.
REMOTE
TALK
TALK
The time and day each
message was received is
announced before the
message begins.
BATT LOW
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
Note: If you want to stop
reviewing your messages,
6
6
9
4
PRS
TUV
WXY
press
.
7
8
9
3. A tone sounds when each
message ends. When all
messages have played, the
announcement “End of
messages” plays.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Press r
4.
to return to
REMOTE
TALK
TALK
Standby.
BATT LOW
1
2
1
The TALK/BATT LOW LED
ABC
DEF
goes off.
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
Base Operation
1. Press NEW MESSAGE
.
Digital Answering System
NEW MESSAGE
STOP
The time and day each
message was received is
announced before the
message begins, and the
Message Counter LED
displays the number of the
message playing.
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO INTERCOM
PAGE/FIND
DELETE
Note: If you want to stop
reviewing your messages,
press the STOP Button.
2. A tone sounds when each
message ends. When all
messages have played, the
announcement “End of
messages” plays.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
3. After the end of message
announcement another tone
sounds, indicating the system
has automatically returned to
Standby.
Digital Answering System
NEW MESSAGE
STOP
4
REPEAT
PLAY
SKIP
The NEW MESSAGE LED stops
flashing, indicating that all of
the new messages have
ANS ON/OFF
OGM
MEMO INTERCOM
DELETE
been reviewed and stored.
PAGE/FIND
Playing a Stored Message
Handset Operation
Press r
1.
.
REMOTE
TALK
TALK
BATT LOW
1
2
1
3
9
ABC
DEF
1
2
3
7
GHI
JKL
MNO
4
5
6
4
PRS
TUV
WXY
7
8
9
2. Press
2
.
REMOTE
TALK
TALK
The first message stored
begins playing.
BATT LOW
1
2
1
ABC
DEF
The time and day each
message was received is
announced before the
message begins.
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
Note: If you want to stop
reviewing your messages,
6
7
8
9
press
.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
3. A tone sounds when each
message ends. When all
messages have played, the
announcement “End of
messages” plays.
Press r
4.
to return to
REMOTE
TALK
Standby.
TALK
BATT LOW
1
The TALK/BATT LOW LED
2
1
goes off.
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
Base Operation
1. Press PLAY
.
Digital Answering System
NEW MESSAGE
STOP
The first message stored
begins playing.
REPEAT
PLAY
SKIP
The time and day each
message was received is
announced before the
message begins. The
Message Counter LED
displays the number of the
message playing.
ANS ON/OFF
OGM
MEMRCOM
PAGE/FIND
DELETE
Note: If you want to stop
reviewing your messages,
press the STOP Button.
2. A tone sounds when each
message ends. When all
messages have played, the
announcement “End of
messages” plays.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
3. After the end of message
announcement another tone
sounds, indicating the system
has automatically returned to
Standby.
Digital Answering System
NEW MESSAGE
STOP
4
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO INTERCOM
DELETE
PAGE/FIND
Repeating a Message
Handset Operation
Press r
1.
.
REMOTE
TALK
TALK
BATT LOW
1
2
1
3
9
ABC
DEF
1
2
3
7
GHI
JKL
MNO
4
5
6
4
PRS
TUV
WXY
7
8
9
2. Press 2 to review your
REMOTE
TALK
messages.
TALK
BATT LOW
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
60
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press 1 at anytime to replay
REMOTE
TALK
a message.
BATT LOW
Note: Pressing 1 during a
message returns the system
to the beginning of that
message. Pressing 1 again
before the message replays
causes the system to scan
back one message. If you
have several messages,
press 1 until you return to
the message you want to
replay.
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
4. To return to Standby,
REMOTE
TALK
press r
.
TALK
BATT LOW
1
The TALK/BATT LOW LED
2
1
goes off.
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
Base Operation
1. Press PLAY to review your
Digital Answering System
messages.
NEW MESSAGE
STOP
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMRCOM
PAGE/FIND
DELETE
61
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press REPEAT at any time to
Digital Answering System
replay a message.
NEW MESSAGE
STOP
Note: Pressing REPEAT
2
during a message returns the
system to the beginning of
that message. Pressing
REPEAT again before the
message replays causes the
system to scan back one
message. If you have several
messages, press REPEAT
until you return to the
REPEAT
PLAY
SKIP
ANS ON/OF
OGM
MEMO INTERCOM
DELETE
PAGE/FIND
message you want to replay.
3. Press STOP at any time to
stop reviewing messages and
return to Standby.
Digital Answering System
NEW MESSAGE
STOP
4
The NEW MESSAGE LED
remains on, and the Message
Counter LED shows the total
number of messages.
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO INTERCOM
DELETE
Note: The system will
automatically return to
Standby if all the messages
play.
PAGE/FIND
Skipping a Message
Handset Operation
Press r
1.
.
REMOTE
TALK
TALK
BATT LOW
1
2
1
3
9
ABC
DEF
1
2
3
7
GHI
JKL
MNO
4
5
6
4
PRS
TUV
WXY
7
8
9
62
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press 2to review your
REMOTE
TALK
messages.
TALK
BATT LOW
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
3. Press 3at any time to skip
REMOTE
TALK
to the next message.
TALK
BATT LOW
Note: Each time 3is
1
2
1
pressed the system scans
forward one message. If you
have several messages,
press 3until you get to the
message you want to play.
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
4. To return to Standby, press
REMOTE
TALK
r
.
TALK
BATT LOW
1
The TALK/BATT LOW LED
2
1
goes off.
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Operation
1. Press PLAY to review your
Digital Answering System
messages.
NEW MESSAGE
STOP
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMRCOM
PAGE/FIND
DELETE
2. Press SKIP at any time to skip
Digital Answering System
to the next message.
NEW MESSAGE
STOP
Note: Each time SKIP is
2
pressed, the system scans
foward one message. If you
have several messages,
press SKIP until you get to the
message you want to play.
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO TERCOM
DELETE
PAGE/FIND
3. Press STOP at any time to
stop reviewing messages and
return to Standby.
Digital Answering System
NEW MESSAGE
STOP
4
The NEW MESSAGE LED
remains on, and the Message
Counter LED shows the total
number of messages.
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO INTERCOM
DELETE
Note: The system
automatically returns to
Standby when all messages
play.
PAGE/FIND
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting a Message
Handset Operation
Press r.
1.
.
REMOTE
TALK
TALK
BATT LOW
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
2. Press 2to review your
REMOTE
TALK
messages.
TALK
BATT LOW
Note: You can press the
Key when you have received
new messages.
8
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
3. If you decide to delete a
REMOTE
TALK
4
message, press
any time
TALK
during the message.
BATT LOW
1
2
1
The system beeps and
immediately goes to the next
message.
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
Note: When you press
4
5
6
you are tagging the message.
A message must be tagged
before it can be deleted.
9
4
PRS
TUV
WXY
7
8
9
65
Download from Www.Somanuals.com. All Manuals Search And Download.
4. If you tag a message for
deletion and replay the
message again before the
end-of-message
REMOTE
TALK
TALK
BATT LOW
1
2
1
announcement, then the
message is untagged and will
not be deleted.
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
For example, you have
received four messages and
you tagged the second
message for deletion. During
the fourth message you
press 1 three times and
replay message 2. If you
don’t tag message 2 for
deletion again before the
“End-of-messages”
4
5
6
9
4
PRS
TUV
WXY
7
8
9
announcement, it will not
be deleted.
Note: If you press 3and
scan to a tagged message,
and then let the message
play, you must retag the
message or it will not be
deleted.
5. When the “End of messages”
announcement plays, you will
hear a series of quick warning
tones for five seconds in the
Handset. This is followed by a
long tone.
Then an announcement such
as “Two messages deleted"
plays.
REMO
TE
1
2
6
1
7
4
3
8
5
?
Note: The deletion
&
INT'C
announcement above depends
on how many messages you
tag for deletion.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
6. The warning tones allow you
to cancel the delete function
and save your messages.
REMOTE
TALK
TALK
BATT LOW
1
2
1
Pressing 2cancels the
delete function and the
messages begin replaying
from the beginning.
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
1
Pressing either 3or
REMOTE
TALK
cancels the delete function.
The messages are saved,
and you can either select
another menu command from
the Handset or press r
and return to Standby.
TALK
BATT LOW
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
Base Operation
1. Press PLAY to review your
Digital Answering System
messages.
NEW MESSAGE
STOP
Note: You can press the
NEW MESSAGE Button when
you have received new
messages.
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO RCOM
PAGE/FIND
DELETE
67
Download from Www.Somanuals.com. All Manuals Search And Download.
2. If you decide to delete a
message, press and release
DELETE any time during the
message.
Digital Answering System
NEW MESSAGE
STOP
2
REPEAT
PLAY
SKIP
The system beeps and
immediately goes to the next
message.
ANS ON/OFF
OGM
MEMO INTERCOM
DELETE
Press &
Release
Note: When you press
DELETE you are tagging the
message. A message must
be tagged before it can be
deleted.
PAGE/FIND
3. If you tag a message for
deletion and replay the
message again before the
“End-of-message”
Digital Answering System
NEW MESSAGE
STOP
2
announcement, then the
message is untagged and will
not be deleted.
REPEAT
PLAY
SKIP
ANS ON/OF
OGM
MEMO TERCOM
DELETE
For example, you have
received four messages and
you tagged the second
message for deletion. During
the fourth message you press
REPEAT three times and
replay message 2. If you
don’t tag message 2 for
deletion again before the
“End-of-message”
PAGE/FIND
announcement, it will not be
deleted.
Note: If you use the SKIP
Button to scan to a tagged
message and then let the
message play, you must
retag the message or it will
not be deleted.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
4. When the “End of messages”
announcement plays, you will
hear a tone and the Message
Counter LED will begin to
flash a delete warning. A long
tone sounds after five
seconds on the Base speaker.
Then an announcement such
as “Two messages deleted"
plays.
Note: The deletion
announcement above
depends on how many
messages you tag for
deletion.
5. The flashing delete warning
displayed by the Message
Counter LED allows you to
cancel the delete function
and save your messages.
Pressing PLAY cancels the
delete function, and the
messages begin replaying
from the beginning.
Digital Answering System
NEW MESSAGE
STOP
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO INTERCOM
PAGE/FIND
DELETE
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Pressing either REPEAT or
SKIP cancels the delete
function, and the messages
are saved.
Digital Answering System
NEW MESSAGE
STOP
2
REPEAT
PLAY
SKIP
Note: If you reviewed all the
messages, NEW MESSAGE
LED will light but will not flash.
ANS ON/OF
OGM
MEMO TERCOM
DELETE
PAGE/FIND
Deleting All Messages
You can delete all your messages without tagging each separate message.
To delete all the messages, you must use the DELETE button on the Base
Unit.
1. Press and hold DELETE
.
Digital Answering System
NEW MESSAGE
STOP
Note: You must review all
messages before using the
“Delete All Messages”
function.
4
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO INTERCOM
DELETE
PAGE/FIND
2. You will hear three short
tones, followed by a longer
tone.
Digital Answering System
NEW MESSAGE
STOP
And “dL” begins to flash in
REPEAT
PLAY
SKIP
the Message Counter LED.
Note: You have five seconds
to cancel delete before all of
the messages are erased.
ANS ON/OFF
OGM
MEMO INTERCOM
PAGE/FIND
DELETE
70
Download from Www.Somanuals.com. All Manuals Search And Download.
3. A long tone sounds, and then
an announcement such as
“Four messages deleted”
plays.
Digital Answering System
NEW MESSAGE
STOP
0
REPEAT
PLAY
SKIP
Note: The deletion
announcement above
depends on how many
messages are stored in
memory.
ANS ON/OFF
OGM
MEMO INTERCOM
DELETE
PAGE/FIND
Message Full Indication
The XCA4500 has a maximum record time of 13 minutes and 42 seconds
or up to 40 incoming messages. When the memory is full, the Answering
System will not record incoming calls. To return the system to normal
operation, follow these steps.
1. When the memory is full, the
phone will ring 10 times
before the announcement
“No remaining time for
incoming messages” plays.
2. The Message Counter LED
Digital Answering Syste
on the Base Unit displays the
FL warning.
NEW MESSAGE
STOP
FL
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO INTERCOM
DELETE
PAGE/FIND
3. You must review your
messages and then delete
some or all of the stored
messages.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Voice-Guided Help Menu
If you are unsure of the commands available while using the Handset, you
can use the Voice-Guided Help Menu. The Handset commands are
reviewed for you on the Handset Receiver. To access the Help Menu,
follow these steps.
Pressr
1.
.
REMOTE
TALK
TALK
The TALK/BATT LOW LED
BATT LOW
1
lights orange.
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
2. Press
?
.
8
?
OPR
A tone sounds, and the
Voice-Guided Menu begins to
play.
0
TONE
MEM
SCRMBL FLASH
CHAN
RDL/P
VOLUME
INT'C
R. TONE
R. VOL
3. There are two ways to exit
REMOTE
TALK
6
the Help Menu—press
time during the review or
any
TALK
BATT LOW
1
listen to all the options and
wait for the system to
automatically exit.
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
72
Download from Www.Somanuals.com. All Manuals Search And Download.
4. When you exit Help, you will
hear a short tone every three
seconds, indicating that the
system is in the Command
Waiting Mode. Press another
REMOTE
TALK
TALK
BATT LOW
1
2
1
ABC
DEF
command, or press r
,
1
2
3
to return to Standby.
7
3
GHI
JKL
MNO
Note: You have 20 seconds
to enter another command
while in the Command
Waiting Mode before the
system automatically returns
to Standby.
4
5
6
9
4
PRS
TUV
WXY
7
8
9
When you return to Standby,
the TALK/BATT LOW LED goes
off.
Screening Incoming Calls
If you receive a call while your Answering System is on, you can listen to the
OGM announcement and the incoming message on the Base Unit speaker. If
you are away from the Base, you can use your Handset to screen incoming
calls.
Press r
1.
after the
REMOTE
TALK
phone
begins to ring.
TALK
BATT LOW
1
2
1
The TALK/BATT LOW LED
ABC
DEF
lights orange.
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
73
Download from Www.Somanuals.com. All Manuals Search And Download.
2. You can now listen to the
OGM and incoming message
on the Handset receiver. If
you decide to answer the call,
press T .
REMOTE
TALK
TALK
BATT LOW
1
2
1
ABC
DEF
1
2
3
Note: The Answering System
stops recording the incoming
message when T is
pressed.
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
3. When you finish the call,
press T to hang up.
The TALK/BATT LOW LED
goes off.
Leaving a Memo Message
You can use the XCA4500A to leave a Memo Message for someone else
who uses your Answering System.
1. To record your Memo
Digital Answering System
Message, press and hold
the MEMO Button until you
hear a long tone and the
Message Counter LED
begins to count up.
NEW MESSAGE
STOP
0
REPEAT
PLAY
SKIP
ANS ON/OFF
OGM
MEMO INTERCOM
DELETE
PAGE/FIND
74
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Speak into the microphone.
When you are finished
recording, release the MEMO
Button.
Digital Answering System
NEW MESSAGE
STOP
REPEAT
PLAY
SKIP
There is a tone, and the
NEW MESSAGE LED begins to
flash. The Message Counter
LED shows the total number
of messages stored in
memory.
ANS ON/OFF
OGM
MEMO INTERCOM
PAGE/FIND
DELETE
3. After you have recorded your
message, the system returns
to Standby.
Note: If you have new or
unplayed messages, the
NEW MESSAGE LED on the
Base Unit continues to flash.
If all the messages have
been reviewed, the
NEW MESSAGE LED remains
on but doesn’t flash.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a Telephone Conversation
To record a conversation during a call:
Press r
1.
.
REMOTE
TALK
TALK
The TALK/BATT LOW LED
changes from red to orange,
and the telephone sounds
warning beeps to let the other
party know that the call is
being recorded.
BATT LOW
1
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
To stop recording, press r
2.
again.
The TALK/BATT LOW LED
changes from orange back to
red.
Note: A recorded call is like a
message—if you use all of
the available record time, the
Recording function cancels
automatically.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Operation
You can operate your XCA4500 while you’re away from home by calling
from any touch-tone phone. When using this feature, remember these
important guidelines.
•
•
•
You should change your Personal Identification Number (PIN)
before using your Handset. When you first apply power, the code is
set to 00.
The dialing keys on a touch-tone phone work the same as the
function keys on your phone’s Handset except you must press #
before selecting a command.
You cannot change the Time and Day Stamp or your PIN code from
a touch-tone phone.
Setting Your PIN Code
Using the Handset, you can set a personal two-digit code (00 to 99) for your
PIN code. You must use your PIN code to access your Answering System
from a touch-tone telephone.
Press r
1.
.
REMOTE
TALK
TALK
The TALK/BATT LOW LED
BATT LOW
1
lights orange.
2
1
ABC
DEF
1
2
3
7
3
GHI
JKL
MNO
4
5
6
9
4
PRS
TUV
WXY
7
8
9
#
2. Press
.
8
?
OPR
0
TONE
MEM
SCRMBL FLASH
CHAN
RDL/P
VOLUME
R. VOL
INT'C
R. TONE
77
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press your two-digit code.
22
For example, use 22 as the
new PIN number.
#
4. Press
again.
8
?
OPR
0
You will hear a long tone
which indicates that the new
code is saved.
TONE
MEM
SCRMBL FLASH
CHAN
RDL/P
VOLUME
R. VOL
INT'C
R. TONE
Press r
5.
again to return
REMOTE
TALK
to Standby.
TALK
BATT LOW
1
2
1
3
9
ABC
DEF
1
2
3
7
GHI
JKL
MNO
4
5
6
4
PRS
TUV
WXY
7
8
9
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Touch-Tone Phone
You can operate your Answering System using any touch-tone telephone.
Use this function to check for recorded messages, play or delete messages,
or even record a new outgoing message.
1. Call your telephone number.
2. During the OGM playback,
press
#
followed by your PIN
number.
For example, use 33 as
the new PIN number.
3. The Answering System
announces the Time and Day
Stamp followed by the
number of messages stored
in memory. When messages
are stored in memory, the
system automatically begins
playing them now.
4. You then hear intermittent
beeps indicating that the
system is in the Command
Waiting Mode.
Note: You must enter a
command within 20 seconds
or the Answering System
hangs up and returns to
Standby.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Use this chart to select the
function you want.
Function
Repeat
Press
#1
Play
#2
Skip
#3
Delete Message
Answer On/Off
Stop
#4
#5
#6
Record OGM
Play New Message
Replay OGM
Help Menu
#7
#8
#9
#0
6. When you’ve finished, hang
up to exit the system.
Your Answering System
automatically returns to
Standby.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If your XCA4500A Integrated Telephone Answering Device is not
performing to your expectations, please try these simple steps. If you are still
unable to resolve the problems, contact Uniden Customer Service at
(800) 297-1023, 8:00 a.m. to 5:00 p.m. Central, Monday through Friday.
Telephone Troubleshooting Chart
Problem
Suggestion
•
•
•
Make sure AC Adapter is plugged
into the Base Unit and wall outlet.
Charge light won’t come on when
Handset is placed in Base Unit.
Make sure Handset is properly
seated in Base Unit.
Make sure that the charging contacts
on the Handset and Base Unit are
clean.
•
•
•
•
•
Make sure that the Base Unit
Audio sounds weak and/or scratchy.
Can’t make or receive calls.
antenna is fully extended and vertical.
Move the Handset and/or Base Unit
to different locations and try again.
Press the CHAN Button to select
another channel.
Check both ends of the Base Unit
telephone line cord.
Make sure the AC Adapter is
plugged into the Base Unit and wall
outlet.
•
•
Disconnect the AC Adapter for a few
minutes, and then reconnect it.
Nickel-Cadmium battery pack may
be weak. Charge the battery on the
Base Unit for 15–20 hours.
Handset doesn’t ring or receive a page.
•
•
•
•
•
•
Set the RING ON/BATT SAVE switch on
the Handset to RING ON
.
Extend the Base Unit antenna
vertically.
The Handset may be too far away
from the Base Unit.
Place the Base Unit away from noise
sources.
The Digital Security Code may be
erased. Set the Digital Code.
Set the Base Unit Ringer switch to
Base Unit doesn’t ring or receive a
page.
LO or HI
.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering System Troubleshooting Chart
Problem
Suggestion
•
•
•
•
•
•
Make sure that the Base Unit is
plugged in.
Answering System does not work.
Make sure the Answering System is
turned on.
Press the RESET button to reset the
system after an AC line spike.
Set the REC TIME/ANN-1 switch in the
right-hand position.
Answering System does not answer
calls.
The memory may be full. Delete
some or all of the saved messages.
The incoming messages may be too
long. Remind callers to leave a brief
message.
Messages are incomplete.
•
•
•
If you have Call Waiting, set the CPC
switch to OFF
.
The memory may be full. Delete
some or all of the saved messages.
Check the battery backup, and
replace the battery if necessary.
After a power failure, the OGM is
deleted.
•
There has been a power failure and
the battery backup has been
completely discharged. Replace the
battery, and press STOP to reset the
Answering System.
Message Counter LED flashes the
letter
P.
•
•
Replace the backup battery as soon
as possible.
The BATTERY LED on the Base Unit
flashes.
Adjust the volume control on the side
of the Base Unit.
No sound on the Base Unit speaker
during call monitoring or message
playback.
•
Press the VOLUME/R. VOL key when
using the Handset to adjust the
volume.
The Handset Receiver volume is not
loud enough.
•
•
Make sure you’re using the correct
Cannot access remote call-in features
from another touch-tone phone.
PIN number.
Make sure that the touch-tone phone
you’re using can transmit the tone for
at least two seconds. If it cannot, you
may have to change to another
phone.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General – The XCA4500A complies with FCC Rules, Parts 15 and 68.
Frequency Control
Modulation
Phase Locked Loop (PLL) Synthesizer
FM
Operating Temperature
– 10° to 50° C
Base Unit
Receive Frequency
Transmit Frequency
Power Requirements
Size
48.76 to 49.99 MHz (25 Channels)
43.72 to 46.97 MHz (25 Channels)
120V AC 60 Hz
8 38 in. (W) x 5 17 in. (D)
32
x 1 78 in. (H)
Weight
Approx. 18.9 oz.
Handset
Receive Frequency
Transmit Frequency
Power Requirements
Size
43.72 to 46.97 MHz (25 Channels)
48.76 to 49.99 MHz (25 Channels)
Rechargeable Ni-Cd Battery Pack
3
11
3
2 16 in. (W) x 2 in. (D) x 12 32 in. (H) (w/ antenna)
16
Weight
Battery
Approx. 10 oz. (including battery)
BT-185
Capacity
270 mAh, 3.6V
6 hours
Talk Mode
Standby Mode
Battery Save Mode
7 days
5 weeks
Answering System
Memory Type
Memory Capacity
Message Length
Digital Tapeless Recording
13 min., 42 sec. (40 messages)
1 min. Incoming Message (max.)
1 min. OGM (max.)
Specifications, Features, and availability of Optional Accessories are all
subject to change without prior notice.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
®
XCA4500
Integrated Telephone
Answering Device
:
,
UDZZ01355ZZ
Operating Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
Before you read anything else,
please observe the following:
WARNING!
Uniden America Corporation DOES NOT represent this unit to be waterproof.
To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT
expose this unit to rain or moisture.
RECHARGEABLE NICKEL-CADMIUM
BATTERY WARNING
This equipment contains a Rechargeable Nickel-Cadmium
Battery.
Cadmium is a chemical known to the State of California to
cause cancer.
The Rechargeable Nickel-Cadmium Battery contained in this
equipment may explode if disposed of in a fire.
Do not short-circuit the battery.
Do not charge the Rechargeable Nickel-Cadmium Battery
used in this equipment in any charger other than the one
designed to charge this battery as specified in this Guide.
Using another charger may damage the battery or cause the
battery to explode.
RECHARGEABLE NICKEL-CADMIUM
BATTERIES MUST BE RECYCLED OR
DISPOSED OF PROPERLY
Residents of Minnesota should contact 1-800-225-PRBA for
information concerning reclamation and disposal of
Rechargeable Nickel-Cadmium batteries.
Residents outside of Minnesota should contact their local
authorities for information concerning reclamation and
disposal of Rechargeable Nickel-Cadmium batteries.
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering Device Remote Keys
1
2
3
1. Repeat Key
1
2. Play Key
2
3
REMOTE
TALK
TALK
3. Skip Key
BATT LOW
1
4. Message Delete
2
1
Key
4
ABC
DEF
5. Answering System
1
5
6
2
3
On/Off Key
5
6
4
7
3
6
4
7
6. Stop Key
JKL
GHI
MNO
7.
OGM7Record
4
5
8
9
6
Key
9
8.
9.
PKleayy8New Message
TUV
PRS
WXY
7 8
8
9
11
12
OGM9Review
?
&
10
Key
OPR
10. Time/ Day Stamp
0
Reset
*
TONE
11. Voice Guided Help
MEM
1
2
CHAN
RDL/P
Key
?
VOLUME
R. VOL
12. PIN/Security Key
#
INT'C
R. TONE
Download from Www.Somanuals.com. All Manuals Search And Download.
Handset Controls and Keys
1
1. Antenna
2. Talk/Battery Low
Indicator
3. Talk Button
T
4. Numeric Keypad
5. Tone Button
*
9
6. Memory
2
3
RING
ON
Programming
Button
M
REMOTE
TALK
TALK
7. Intercom Button
J
BATT
SAVE
BATT LOW
1
2
1
ABC
DEF
8. Flash Button
/ Ringer Tone Select
Button
F
1
2
3
10
3
6
7
O
GHI
JKL
MNO
4
5
6
9. Remote Button
9
4
4
5
PRS
TUV
WXY
r
7
8
9
8
?
10. Ring On/Battery
OPR
Save Switch
0
11
12
TONE
MEM
11. One Touch Dialing
1
2
CHAN
RDL/P
6
7
8
Buttons
FLASH VOLUME
R. TONE R. VOL
INT'C
13
14
12. Channel Select
Button
E
13. Redial/Pause
Button
R
14. Volume
V
Ringer Volume
/
Select Button
L
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Unit Controls and Keys
1
2
3
4
5 6
7
8
RING SW PULSE-TONE CPC
2-5-TS OFF-ON
REC TIME RING VOL
ANN-1 OFF-LO-HI
RESET
DC IN 9V
TEL-LINE
+
-
9
10
®
CHANNEL
ULTRACLEAR
PLUS
11
12
13
Digital Answering System
NEW MESSAGE
0
IN USE
BATTERY
CHARGE
REPEAT
PLAY
SKIP
STOP
14
ANS ON/OFF OGM
MEMO INTERCOM
15
16
DELETE
Extend•A•Phone
SERIES
POWER
H
Q
MIC
PAGE/FIND
17
26
25
23
20 19 18
22 21
24
1. Ring Switch (2-5-TS)
14. Message Play Button
15. Message Skip Button
16. Intercom Button
17. Memo Button
18. Outgoing Message Button
19. Answering System On/Off Button
20. Stop Button
2. Pulse/Tone Switch
3. Calling Party Control Switch
4. Record Time/Ann-1 Switch
5. Ringer Volume Switch
6. Telephone Line Jack
7. DC Power Jack
8. Reset Button
9. Handset Retainer
10. Base Unit Antenna
11. New Message LED/Button
12. Message Counter LED
13. Message Repeat Button
21. Message Delete Button
22. Power LED
23. Charge LED
24. Battery LED
25. In Use LED
26. Microphone
Download from Www.Somanuals.com. All Manuals Search And Download.
One Year Limited Warranty
Important: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original
retail owner, this Uniden Product to be free from defects in materials and
craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate
and be of no further effect 12 months after the date of original retail sale. The
warranty is invalid if the Product is (A) damaged or not maintained as
reasonable or necessary, (B) modified, altered, or used as part of any
conversion kits, subassemblies, or any configurations not sold by Uniden,
(C) improperly installed, (D) serviced or repaired by someone other than an
authorized Uniden service center for a defect or malfunction covered by this
warranty, (E) used in any conjunction with equipment or parts or as part of
any system not manufactured by Uniden, or (F) installed or programmed by
anyone other than as detailed by the Operating Guide for this product.
STATEMENT OF REMEDY: In the event that the product does not conform
to this warranty at any time while this warranty is in effect, warrantor will
repair the defect and return it to you without charge for parts, service, or any
other cost (except shipping and handling) incurred by warrantor or its
representatives in connection with the performance of this warranty. THE
LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE
WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND
EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY
OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR
PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion
or limitation of incidental or consequential damages so the above limitation
or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. This warranty is
void outside the United States of America.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If,
after following the instructions in this Operating Guide you are certain that
the Product is defective, pack the Product carefully (preferably in its original
packaging). Include evidence of original purchase and a note describing the
defect that has caused you to return it. The Product should be shipped
freight prepaid, by traceable means, or delivered, to warrantor at:
Uniden America Corporation
Parts and Service Division
4700 Amon Carter Boulevard
Fort Worth, TX 76155
(800) 297-1023, 8:00 a.m. to 5:00 p.m. Central, Monday through
Friday
Download from Www.Somanuals.com. All Manuals Search And Download.
Covered under one or more of the following U.S. patents:
4,511,761
4,595,795
4,523,058
4,797,916
®
©1995 Uniden America Corporation.
Printed in Hong Kong
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|