INSTALLATION GUIDE
3250
3250M
Advanced 2-Way
Remote Vehicle Starter
AUTOMATIC AND MANUAL
TRANSMISSION MODELS
WWW.ULTRASTARTERS.COM
See website for a full size printable version of this manual.
FCC/ID Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the
following conditions:
TECH SUPPORT
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part
responsible for compliance void the user’s authority to operate this devise.
Western Canada 1 800 279-0636
United States: 1 866 698-5872
Eastern Canada Bilingual: 1 800 268-0683
Download from Www.Somanuals.com. All Manuals Search And Download.
1
3
5
2
4
6
Jumper Selectable
**** These connection’s are only necessary for installation’s on manual transmission vehicles.
Always install a “M” Series Remote Starter on manual transmission vehicles.
3 PIN
RED
Note: Do not use the center pin of this connector to power relay packs.
Doing so will damage the output. Always use a fused power source when
installing relays for keyless entry.
FM ANTENNA WITH DUAL LED’S A
BUILT-IN VALET SWITCH
4 PIN
Blue
Note: The antenna must be connected before the system will operate.
Jumpers
The jumpers control the output on the white wire from the six pin
harness. Place the jumpers in the above order to change the output.
Note: The default setting is Second Ignition.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Components
- Control module
- 2way LCD transmitter
- FM Antenna with built in Program Button and LED’s
- 6 pin main harness with dual 30amp power inputs.
- 14 pin harness
- 4 pin keyless entry harness
- Hood pin safety switch
- Under hood / window stickers
- Installation guide
- Owners manual
Recommended Pre-Installation Procedures
BEFORE STARTING INSTALLATION:
- Discuss the optional features with the customer.
- Take a few minutes to review the installation and owners manuals.
- Check if the vehicle has a factory security or anti-theft system.
*If equipped, inform the customer of addition parts and labour.
- Do a walk around the vehicle and check for any damage.
- If installing a LED discuss the placement with customer before installing.
Note: This remote starter is designed for fuel injected and diesel engines.
Recommended Installation Procedures
Proper Connections - Remote Starters can handle loads of up to 30 amps for extended periods of time. It
is CRITICAL to insure that ALL high current connections are properly soldered and insulated with quality
electrical tape. Failing to insure proper connections will result in warranty being VOID and can result in a
FIRE. The manufacturer is not responsible for any such damages. It only takes a few more minutes to do the
job RIGHT.
Under Hood Connections - Route the hood pin and tach wires through the firewall into the engine
compartment. Always try to pull the wires through a factory rubber grommet. If drilling through the firewall, BE
CAREFUL. Check for obstructions on both sides of the firewall. After drilling use a snap in grommet to protect
the wires from sharp edges.
Installing the External Long Range Antenna - To insure the best possible reception, place the
antenna in the center of the windshield, behind the rear view mirror. Before attaching to the glass ensure that
the surface is clean and dry. For best results with range, place the antenna below the tint screen. Run the
cable under the headliner and behind the A-pillar panel. Be careful not to pinch the antenna cable. Plug the
antenna into the BLUE connector on the Control Module.
NOTE: This step is not used on Alarm Only Units with no External Antenna.
Mounting The Control Module - Never mount the module in the engine compartment. Select a location
under the dash to install the main module. Be certain that the module is securely attached and does not
obstruct any serviceable areas. Do not force or jam the module into tight places instead of mounting. The
module must be free from all moving parts such as brake and clutch and gas pedals linkages. Do not place
the module directly in front of a heater vent.
Testing The System - When the installation is complete, it will be necessary to test that the system is
working correctly. The system’s default programming will work on the majority of vehicles, but might need to be
adjusted for some applications. If the installation requires special timing or additional features, proceed to
Program Mode.
ATTENTION: Hood Pin MUST always be connected!!
NOTE: Always inform user to place system in Service Mode before any service work is performed on
the vehicle.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Pin Power Connector
Yellow
Green
Red
Red
Blue
Starter
Heater
12 power
12 power
Ignition 1
Select Out
30amp output
30amp output
30amp input
30amp input
30amp output
30amp output
12volts during crank only.
12volts in accessory off during start.
Constant 12volt power at ignition harness.
Constant 12volt power at ignition harness.
12volts in ignition and start positions.
Selectable Output. See jumper diagram.
White
14 Pin Connector
Yellow
Red/White
Brown
Orange
White/Blue
Black/White
Purple
Re-Arm
0.75sec Pulse With Lock And On Shutdown.
3rd CH
Disarm
(-) Out
Trunk Release - Hold button #2 for 5 seconds
0.75sec Pulse With Unlock And Before Start.
(-)While Running / Negative While Locked *Starter Program Mode.
Horn Honk Output *User Program Mode
Horn (-)
Park Brake Negative Park Brake Input - Manual Transmission Models Only.
(+) Door Positive Door Input - Manual Trans And Alarm Units Only.
White
Green/White
Green
Black
Pink
Park Lights Positive Park Light Output - 10 Amp Max.
Hood Pin Negative Hood Pin Input - MUST BE CONNECTED!!
(-) Door
Ground
Brake
Negative Door Input - Manual Transmissions Only.
System Ground Input - MUST BE CONNECTED!!
Positive Brake Input - MUST BE CONNECTED!!
Blue/White
Blue
Tach
Tach Signal Input - MUST BE CONNECTED ON TACH MODELS!!
Glow Plug Programmable Input - DIESEL ONLY. * Starter Program Mode
3 Pin Connector Red
Green
Red
Blue
Lock
12vlt Output
Door Unlock
Door Lock Output - Programmable - Menu 1 Setting 3.
Low current output for Voltage Inverter Only.
Door Unlock Output - Programmable - Menu 1 Setting 3.
Note: Do not use the center pin of this connector to power relay packs. Doing so will damage the output.
Always use a fused power source when installing relays for keyless entry.
4 Pin Connector Blue
Antenna/ Program Button Connector.
The Antenna Must Be Connected Before the System will Operate.
Jumper Selections
Position One
Position Two
Position Three
Second Starter Output On the White Wire From The 6-Pin Connector.
Second Accessory Output On The White Wire From The 6-Pin Connector.
Second Ignition* Output On The White Wire From The 6-Pin Connector.
To change the jumper position you must first remove the access cover from the top of the module. Remove
the cover as shown in the diagram below. The access cover will slide out of its position when pushed
outwards from the center of the module.
The jumpers control the output on the white wire from the six pin harness. To change the output of this
wire, place the jumper in one of the following positions
Note: The default setting is second ignition.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1 - Connect All Of the Following Wires
6 Pin Power Connector
Yellow
Green
Red
Red
Blue
Starter Output
Heater Output
12 power Input
12 power Input
Ignition 1 Output
Selectable Output
Connect To The Vehicles Starter Wire.
Connect To The Vehicles Accessory Wire.
Connect To Constant 12 Volt Power Source- High Current.
Connect To Constant 12 Volt Power Source- High Current.
Connect To The Vehicles Primary Ignition.
White
Default Second Ignition Output. See Page 5.
14 Pin Power Connector
Black
Pink
White
System Ground
Brake Switch
Park Light
Connect To Chassis Ground.
Connect To (+) When Brakes Applied.
Connect To (+) Park Light System.
Connect To Hood Pin Switch.
Green/White Hood Pin
Blue/White Tach Wire
Connect To A/C Tach Source. Tach Models Only
Manual Transmissions Only
Purple
Green
Black/White
(+) Door Pin
(-) Door Pin
Park Brake
Connect to door pin on vehicles with (+) door pin systems.
Connect to door pin on vehicles with (-) door pin systems.
Connect to Park brake switch. (-) when switch is applied.
Note: Manual Transmission units MUST be set into Reservation Mode to remote start.
See page 12 for details.
Step 2- Plug-In The Module
When all the connections are done, the control module can be plugged in. Before connecting the control
module, make sure the ignition is in the OFF position. Plug in the 6 pin harness then the 14 pin followed by
any other connectors that were used.
Step 3- Auto Tach Learn
1) Make all the required wire connections and plug-in the Unit.
**The park lights should flash twice upon power up.
2) Turn the Ignition Key ON. (Park Lights will turn on).
3) Start the vehicle, LED’s on antenna will come when proper tach signal is detected**, then after 30-35
seconds the park lights will turn off then flash twice to confirm tach learning.
* The system will flash the park lights seven times if not tach learned and the start button is
pressed. The system must be tach learned before remote starting.
** If the LED’s do not come on during tach learn, a proper tach signal was not detected
Note: If the park lights do not flash in auto tach learn mode it may be necessary to connect to a different tach
source. For best results connect the tach wire to the coil pack or to a fuel injector wire. See Page 8 for tach
adjustment.
***New - A system reset must be done before a new tach signal can be learned to the system.
Your Basic Install Is Complete!
NOTES:
1) IfYtheounuitrdoeBs naotsstairct, checIknthse sttaartelrlisantotiinoTnach iLsockNOutoorwin PrCogroammModpe.lete!!
2) If the vehicle still does not start, check all connections and check for factory security.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Overview
Program mode allows you to adjust the settings and options of your system.
Your system has been intelligently designed by installers with years of experience. The system’s default settings
do not require any program changes in most cases. However, this system does incorporate a highly advanced
programming system that includes 4 menus with numerous options and settings that can be easily adjusted for
custom installations and applications.
User Settings - Page 8
This program menu contains settings that adjust the way the system operates for the user.
Additional Settings - Page 8
This program menu contains settings that control additional user options.
Starter Settings - Page 9
This menu controls features and settings associated with remote car starter applications.
Tach Settings - Page 10
This menu allows the programming of the tach signal and the manual adjustment of that setting.
Entering Program Mode
1) Make sure ignition is in the off position.
2) Within three seconds turn the key ON - OFF - ON - OFF - ON. Leave in the “ON” position.
3) Press and release the Program Button on the antenna 1 time.
4) Park lights will come on and the horn (optional) will honk to confirm entering Program Mode.
5) Select Desired Program Menu by the following:
Press Button #1
Press Button #2
Press Button #3
Press Button #4
Lock
Unlock
Start
Aux
User Options
Page 8
Page 8
Page 9
Page 10
Additional Options
Remote Start Options
Tach Adjustment Menu
6) The selected mode will be confirmed by a horn honk (if connected)and one park light flash.
7) The Program Menu may be changed at any time by pressing the transmitter buttons as above, this allows
the installer to change a setting from one menu, then quickly jump to another menu and change another
setting without re-entering the Program Mode.
8) Turning off the ignition or 30 seconds of no activity will exit the Program Mode. This will be confirmed by 1
long horn honk and park light flash.
Note: If unit does not enter Program Mode, turn ignition off for 5 seconds and repeat steps 1-4. ** The first
ignition(Blue)MUST be connected to the vehicle’s first ignition wire. If it is not connected
It will not be possible to enter the Program Modes.
Changing the Programmable Settings
1) Enter Program Mode.
2) Select the desired Program Menu. (See pages 8 - 10)
3) Press & release the Program Button the correct number of times to select the desired Program
Setting(as listed on pages 8 -10). The park lights will flash and the horn (optional) will honk to indicate the
current setting that is selected.
4) Hold the Program Button until the parking lights /horn confirm the selected setting. The park lights will
flash and the horn (optional) will honk to indicate the option selected within the setting.
5) Turn the ignition key “Off” to exit Program Mode.
Note: This procedure is listed in below each program setting on pages 8 - 10 of this manual.
SYSTEM RESET
1) Within 3 seconds turn the key ON-OFF-ON-OFF-ON (Leaving Key ON).
2) Press and release the Program Button.
3) The park lights will turn ON
4) Press the Program Button a second time and hold for 8 seconds until the park lights flash 3
Times and horn (Optional) honks 3 times.
System is now re-set to factory defaults.
Note: Reset to defaults does not delete the transmitters from memory.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAM MODE 1 - USER SETTINGS
Setting 1- Ignition Auto Lock
1 Ignition Lock & Unlock Enabled
2 Ignition Lock Only
*3 Ignition Auto Lock Disabled
1 Flash
2 Flashes
3 Flashes
Doors Lock / Unlock when the key is turned On/ Off
Doors Lock when ignition key is turned ON only
Doors do not Lock or Unlock with the Ignition key
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 2- Horn Honk Settings
1 Lock & Unlock chirps Disabled
2 Lock & Unlock chirps Enabled
*3 All Chirps Enabled
1 Flash
2 Flashes
3 Flashes
Honks for Panic and Car Finder Mode only.
Honks for Lock, Unlock, Panic and Car Finder Mode Only.
Honks for Lock, Unlock, Start, Panic and Car Finder.
Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 3- Door Lock Options
1 Double Pulse Unlock
2 3 Second Lock & Unlock
*3 0.75 Second Pulses
1 Flash
2 Flashes
3 Flashes
Single .75sec.Lock pulse and double Unlock Pulse
3 second pulses for Lock & Unlock
0.75 second pulses for Lock and Unlock
See setting 4 for door unlock and disarm output durations.
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 4 - Door Unlock & Disarm Pulse Duration
1 Short Pulses
2* Normal
1 Flash
2 Flashes
125ms pulses with Unlock and on the disarm output.
750ms pulses with Lock, Unlock and on disarm output.
Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
Note: Programming this option will change the pulse length of this output from 750ms to 125ms.
PROGRAM MODE 2 - ADDITIONAL SETTINGS
Setting 1 - Secure Valet Mode
1 Secure Valet Active
1 Flash
Valet only if ignition “ON” and Program Button is held for 15 seconds
2* Normal Valet Active
2 Flashes
Valet if ignition “ON” and Program Button is held for 5 seconds
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
Setting 2 - Parking Light Output
1 30 Second Parking Lights on Disarm 1 Flash
Park Lights on for 30 seconds on disarm
Switches the Park Light and the Trunk Release (3rd Ch)
2 Park Light Flashes on disarm
2 Negative Park Light
2 Flashes
3* Normal Parking Lights
3 Flashes
Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
Setting 3 Horn Honk Timing
1
2
5ms Pulsed Output
20ms Pulsed Output
1 Flash
2 Flashes
Short (Quiet) Pulses
Long (Loud) Pulses
*3 10ms Pulsed Output
3 Flashes
Normal (Medium) Pulses
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAM MODE 3 - STARTER SETTINGS
Setting 1- Special Door Lock/ Unlock Operations
1 Type 1
2 Type 2
1 Flash
Unlock before start. Lock pulse after start and shutdown
2 Flashes Lock pulse only after remote starter shuts off
3* Normal Operation
3 Flashes No additional re-lock pulses
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
Setting 2- Gas/ Diesel Mode- Blue Wire on 14-Pin
1 Negative Input/ 30seconds
2 Timed Delay/ 15 Seconds
3* Gas/ Positive Glow Plug
1 Flash
2 Flashes
Waits a maximum 30 seconds before starting.
Ignition ON for 15 seconds before engaging remote starter
3 Flashes Waits 2 seconds to start if no diesel input is detected
Press the Program Button 2 time to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
Setting 3- Rearm Output- Yellow Wire on 14-Pin
1 Type 1
2 Type 2
1 Flash
Pulse after start and with lock
2 Flashes Pulse after start only
3* Factory Re-arm
3 Flashes 0.75 second pulse with lock and after shutdown
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 4- Run Time
1 30 Min Run Time
2 45 Min Run Time
3* 15 Min Run Time
1 Flash
Remote Starter runs for 30min when activated
2 Flashes Remote Starter runs for 45min when activated
3 Flashes Remote Starter runs for 15 min when activated
Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 5-Maximum Crank Time
1 10 Seconds
2 3 Seconds
3*5 seconds
1 Flash 10 sec Max time that starter will stay engaged
2 Flashes
3 sec Max time that starter will stay engaged
3 Flashes
5 sec Max time that starter will stay engaged
Press the Program Button 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 6- Starter Kill/ Bypass Module Output- Orange wire on 14-Pin Con.
1Active Starter Kill
2Passive Starter Kill 2 Flashes
3*Bypass Module 3 Flashes
1 Flash
On when locked, Before ignition and 2 seconds after ignition turns off.
Same as setting 1 but will arm 60sec after the ignition turns off.
Output before ignition. Stays on 2 seconds after ignition turns off.
Press the Program Button 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 7- Safety Start Mode
1 Safety ON
1 Flash
Must press the start button twice to remote start the vehicle
2* Safety OFF
2 Flashes
Press the start button once to remote start the vehicle.
Press the Program Button 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAM MODE 4 - TACH SETTINGS
Setting 1- Method 2- Low Idle Learn
Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program Button on the antenna 1 time.
Step 2 - Enter Program Menu 4 - Press the # button on the remote.(Button #4).
Step 3 - Start Vehicle - Using the ignition key, make sure not to turn the key off at any time or your will exit programming.
Step 4 - Press the Button - One time (Led will start flashing in single cycles) then press and hold Program Button for(5sec).
Step 5 - Release the Button - Led should come on steady to indicate correct tach signal the park light will flash to confirm.
Setting 2- Adjust For Over-Crank
Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Program Menu 4 - Press the # button on the remote.(Button #4).
Step 3 - Press the Program Button - 2 times (Led will start flashing 2 times).
Step 4 - Hold the Program Button - For 5 seconds until park lights flash (each time lights flash the setting is reduced).
Step 5 - Release the Button - Exit Program Mode and remote start to test.
Setting 3- Adjust For Under-Crank
Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Program Mode 4 - Press the # on the remote.(Button #4).
Step 3 - Press the Program Button - 3 times (Led will start flashing 3 times).
Step 4 - Press and Hold Program - For 5 seconds until park lights flash (each time lights flash the setting is increased).
Step 5 - Release Program - Exit Program Mode then remote start to test.
Transmitter Operation
Press Once to Lock / Unlock Doors and arm/disarm the alarm.
Press 2nd Time (within 3 sec.)& Hold for Constant Lock Output.
1
Press and hold for 3 seconds to activate Trunk Release / Aux Output
2
Press Once for Start - (2 Times if programmed for Safety Start)
Press and hold for 3 seconds while running to turn off
While running with the key, press the button to activate Idle Mode
3
Press and Release for Status Check
Hold for 3 seconds to enter User Programmable Features
4
2
3
1
4
Press both buttons for 3 seconds to activate Car Finder Mode
2&3
Reservation Mode - Manual Transmission.
Manual Transmission Remote Starters must have both the door trigger and park brake wires connected. Most
installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during
the activation of the remote starter. Never disconnect or alter the switch to be always bypassed. Always use a
“M” Series Remote Starter on a manual transmission vehicle.
Never install an automatic Remote Starter model into a manual transmission vehicle. It is not recommended
to install a remote starter on a convertible type vehicle. If doing so It is highly recommended that a radar
sensor is installed to cover the proximity of the gear shift lever. If the radar sensor is tripped the remote starter
will exit Reservation Mode.
To enter Reservation Mode, the following steps must be followed.
Step 1 - While the vehicle is running, place the transmission in neutral and apply the parking brake.
Step 2 - Press and release the brake pedal. The park lights will activate.
Step 3 - Turn the ignition key off and the vehicle will stay running.
Step 4 - Exit the vehicle and close the door. The vehicle will then shut off*.
Step 5 - The vehicle can now be safely remote started.
* If the vehicle has a dome light delay, the vehicle may stay running until the dome light turns off. This is
normally no longer than 30 seconds. Reservation Mode will automatically be exited if the doors of the vehicle
are opened. The set-up mode will then have to be repeated. Reservation Mode Must be set-up each time the
vehicle is parked.
Note: If the vehicle is not in Reservation Mode and the Start button is pressed, the system will flash
the park lights four times slowly.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmitter Programming
1 - Within three seconds turn the ignition Key ON-OFF-ON-OFF-ON - Leaving Key ON
2 - Press and hold the Program Button - Parking Lights will come ON
**if the park lights do not come on at this point, turn the key off for 5 seconds, the repeat step 1.
3 - Continue to hold the Program Button until park lights go out.
4 - Press button 1 on the remote transmitter (ensure the “#” symbol is not displayed on the LCD)
the park light will flash to confirm transmitter programming.(The ”#” symbol is for Dual Car Mode)
Dual car operation:
Enter the User Programming Mode on the second remote and turn the “#” symbol on.
Program the remote (Step 1-4) After the 1st remote is programmed press button 1 on the 2nd.
Note: Transmitter programming must done quickly. Do not pause more than one second between each
transmitter. All the transmitters to be used must be programmed at the same time. All transmitters not
programmed at this time will be erased from memory for security. The system holds a maximum of 4
transmitter codes including 2nd car remote codes.
System Service Mode
ACTIVATING Service Mode (Valet)
1. While the ignition is “ON” press and hold the Program Button for five seconds.The park lights
will flash five times and the horn (optional)will honk five times to confirm that the system is in
Service Mode.
2. While in Service Mode the remote start functions will be disabled and LED’s will be “ON”
steady. Door locks and trunk release are still operational.
DEACTIVATING Service Mode (Valet)
1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights
will flash two times and the horn (optional)will honk two times to confirm that the system has
exited Service Mode.
2. Remote start functions will return to normal operation.
System Service Mode (Valet) - By Remote
ACTIVATE Service Mode (User Programmable Feature)
1 - Press and hold button 4 for 3 seconds. (The remote will beep twice)
2 - Press button 1 Five times or until the ? starts flashing on the LCD screen.
3 - Press button 3 and the ? symbol will come on solid.
4 - Press button 4 to exit User Program Mode.(System Is Now In Service Mode)
DEACTIVATE Service Mode
1 - Press and hold button 4 for 3 seconds. (The remote will beep twice)
2 - Press button 1 Five times or until the ? starts flashing on the LCD screen.
3 - Press button 2 and the ? symbol will turn off.
4 - Press button 4 to exit User Program Mode.(Serice Mode is Deactivated)
Battery Replacement
When the Battery Icon on the remote indicates that the battery is low the battery should be changed
promptly. Replace with quality 1.5volt “AAA” battery.
Slide
Lift
+
1
-
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Negative Type Door Locks
Vehicle
Lock/Unlock
Switch
Green
Blue
Lock
To Control
Relay or
Actuators
Un
lock
Positive Type Door Locks
Vehicle
Lock/Unlock
Switch
Un
lock
Lock
Fused +12V
87
87
87a
Green
Blue
87a
86
86
85
85
30
30
To Control Relay
or Actuator
5 Wire / Reverse Polarity Type Door Locks
Fused +12V
87
87
87a
Green
87a
86
86
85
85
30
30
Blue
Lock
Vehicle
Lock/Unlock
Switch
x
Cut
To Actuator
Un
lock
x
Cut
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|