INSTALL GUIDE
Covers All 430, 440, 441 and CJ Series
Advanced Security Systems
Technical Support: 866-698-5872 ext 0
FCC/ID Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance
void the user’s authority to operate this devise.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE VEHICLE SECURITY
INSTALL MANUAL
PAGE 3
For modules with 10 pin connector only. See page 4 for 11 pin connector.
*500ma negative output
Orange
Gray
(-) When Armed
*500ma negative output
Trunk Release
Ignition Input
Connect to vehicles ignition wire
Connect to constant power. 20amp input
Connect to Siren wire. 2amp Maximum
Connect to chassis ground
Yellow
Red
12 Volt Input
Brown
Black
Siren Output
Ground Input
Door Input
Connect to door pin. (+) when opened
Connect to door pin. (-) when opened
Connect to hood and / or trunk pin
Purple
Green
Blue
Door Input
Hood Input
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL MANUAL
PAGE 4
REMOTE VEHICLE SECURITY
For modules with 11 pin connector only.
*500ma negative output
(-) When Armed
Orange
Gray
*500ma negative output
Trunk Release
12 Volt Input
Connect to constant power. 20amp input
Connect to Siren wire. 2amp Maximum
Connect to chassis ground
Red
Brown
Black
Siren Output
Ground Input
Hood Input
Connect to hood and / or trunk pin
Blue
Connect to door pin. (-) when opened
Connect to vehicles ignition wire
Green
Door Input
Ignition Input
Door Input
Dome Light
Yellow
Purple
Blk/White
Connect to door pin. (+) when opened
Dome Light Supervision Output (-)
Red
Blue
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE VEHICLE SECURITY
INSTALL MANUAL
PAGE 5
Wiring Descriptions
10 Pin / *11 Pin Connector
White
Orange*
Grey*
Yellow
Red
Brown
Black
Purple
Green
Blue
(+) Park lights
(-) When Armed
(-) Trunk Release
(+) Ignition Input
(+) 12Volt Input
(+) Siren Output
(-) Ground Input
(+) Door Input
(-) Door Input
Park light output.
Negative output when system is armed.
Negative output for trunk release.
Input from vehicles ignition wire.
Constant 12 Volt input.
Positive output for siren.
System ground input.
Positive door pin switch input.
Negative door pin switch input.
Negative input from hood pin switch.
(-) Hood Input
Blk/White* (-) Dome Supervision 30 second (-) output when disarmed.*
*This wire is only available on models with the 11 pin connector.
3 Pin Connector Red
Green*
Red*
Blue*
(-) Door Lock
(+) 12 Volt Output
(-) Door Unlock
Door Lock Output (Programmable)
12Volt Output for voltage inverter.
Door Unlock Output (Programmable)
*NOTE: 500ma outputs ONLY!
Recommended Installation Procedures
Mounting the module-Never mount the module in the engine compartment.
Select a location under the dash to install the main module. Be certain that the
module is securely attached and does not obstruct any serviceable areas.
Mount the module so that it cannot be seen if looking under the dash as it could
be easily unplugged by a thief. The module must be free from all moving parts.
Under Hood Connections- Route the hood pin (optional) and Siren wire
through the firewall, into the engine compartment. Always try to pull the wires
through a factory rubber grommet. If drilling through the firewall, BE CAREFUL.
Check for obstructions on both sides of the firewall. After drilling use a snap in
grommet to protect the wires from sharp edges.
Mounting the Siren- Choose a location in the engine compartment that is
away from high heat sources and direct exposer to water. The siren should be
mounted as well as grounded to solid metal. Run the wiring for the siren so that
it can not be seen or reached from below the vehicle.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL MANUAL
PAGE 6
REMOTE VEHICLE SECURITY
Recommended Installation Procedures
Installing the LED- Choose a location that will be highly visible when the
LED is installed. Most vehicles are equipped with knock out panels in the
dashboard, these panels are easily removable and can be easily replaced if
necessary. Once the location is picked, use drill bit and drill a hole through the
panel. Test fit the LED into the hole. Plug the Led into the Red connector on the
main module.
Installing the Program Button- Choose a location to mount the Program
Button. This location should be hidden and not visible from outside the vehicle.
Once the location of the switch is picked, use a 1/4” drill bit and drill a hole.
Remove the nut and push the Program Button through the hole. Replace the
nut and tighten until the switch is secure. Plug the Program Button into the
Blue connector of the main module.
Basic Install
Step 1 - Connect All Of the Following Wires
Black
Yellow
Red
Ground Input
Ignition Input
Power Input
System ground input.
Input from vehicles ignition wire.
Constant 12 Volt input.
Brown
White
Green*
Purple*
(+) Siren Output Positive output for siren.
(+) Park lights
(-) Door Input
(+) Door Input
Positive park light output.
Negative door pin switch input.
Positive door pin switch input.
*Test for door pin type (+ or -) then connect the appropriate wire.
Step 2- Plug-In The Module
Step 3- Test And Adjust The Shock Sensor (see page 3)
Step 4- Test The System
Your Basic Install Is Complete!
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE VEHICLE SECURITY
INSTALL MANUAL
PAGE 7
Programming
To Enter Program Mode
1) Make sure ignition is in the off position.
2) Within three seconds turn the key ON the OFF.
3) Press and release the Program Button two times.
4) The siren will chirp and the lights will flash once to confirm.
NOTE: If unit does not enter Program Mode, repeat steps 2-3.
** The ignition input wire(yellow on the 10 pin connector) MUST be connected.
If it is not connected it will not be possible to enter the Program Mode.
Changing A Programmable Setting
1) Enter Program Mode As explained above.
2) When in program Mode, change the desired Program Setting by pressing
the transmitter buttons in the following sequences.
NOTE: The Systems Default Setting Are Shown In Bold Lettering.
#1
#3
#2
#1 #2
#3
Quick View Programming
Programmable Feature
Shock Sensor Disable
Arm / Disarm Chirps
Ignition Auto Locks
Door Lock Timing
Double Pulse Unlock
Door Input / Voltage Sense
Passive / Active Locks
Passive / Active Arming
Car Jack Mode*
Press Buttons
One Chirp
Two Chirps
Enabled
Chirps On
On
.75 Second
Single Pulses
Door Pin
Passive
#3-#3-#1
#2-#1-#1
#1-#3-#2
#1-#3-#1
#2-#2-#1
#1-#1-#3
#3-#3-#2
#1-#2-#3
#2-#1-#3
#3-#2-#1
#3-#3-#3
Disabled
Chirps Off
Off
3 Second
Two Pulses
Voltage
Active
Active
Deactivated
Siren
Passive
Activated
Horn
Siren/ Horn Output**
System Reset
Confirmed by Three Siren Chirps
*CJ series ONLY
**441 series ONLY
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL MANUAL
PAGE 8
Enter Program Mode
REMOTE VEHICLE SECURITY
Entering program mode is done by the following steps:
1) Make sure ignition is in the off position.
2) Turn the ignition key ON - OFF, leaving key in the OFF position.
3) Press and release the Valet button two times.
4) The siren will chirp one time to confirm entering program mode.
( If this does not happen, turn ignition off, wait five seconds and repeat steps 1-4).
Shock Sensor Disable
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)
2 - Press & release transmitter buttons in the following sequence:
#3 - #3 then #1
3 - The siren will respond with the following:
1 Chirp
2 Chirps
Shock Sensor OFF
Shock Sensor ON
Arm/ Disarm Chirp
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)
2 - Press & release transmitter buttons in the following sequence
#2 - #1 then #1
3 - The siren will respond with the following:
Chirps Disabled
Chirps Enabled
1 Chirp
2 Chirps
Ignition Auto Locks
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)
2 - Press & release transmitter buttons in the following sequence
#1 - #3 then #2.
3 - The siren will respond with the following:
1 Chirp
2 Chirps
Auto Lock Disabled
Auto Lock Enabled
Door Lock Timing
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)
2 - Press & release transmitter buttons in the following sequence
#1 - #3 then #1
3 - The siren will respond with the following:
1 Chirp
2 Chirps
3 Second Door Locks
0.75sec Pulses
Double Pulse Unlock
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)
2 - Press & release transmitter buttons in the following sequence
#2 - #2 then #1.
3 - The siren will respond with the following:
1 Chirp
2 Chirps
Double Pulse Unlock
Single Pulse Unlock
NOTE: Repeat sequence to change selection
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE VEHICLE SECURITY
INSTALL MANUAL
PAGE 9
Voltage / Door Pin Sensing
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)
2 - Press & release transmitter buttons in the following sequence
#1 - #1 then #3
3 - The siren will respond with the following:
1 Chirp
2 Chirps
Voltage Sensing- No Door Pin Connection Needed
Door Pin- Door Pin Connection Required
Passive / Active Locks
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)
2 - Press & release transmitter buttons in the following sequence
#3 - #3 then #2
3 - The siren will respond with the following:
1 Chirp
2 Chirps
Active Locks
Passive Locks
Passive / Active Arming
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)
2 - Press & release transmitter buttons in the following sequence
#1 - #2 then #3
3 - The siren will respond with the following:
1 Chirp
2 Chirps
Active Arming
Passive Arming
Car Jack Mode (CJ series ONLY)
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)
2 - Press & release transmitter buttons in the following sequence
#2-#1 then #3
3 - The siren will respond with the following:
1 Chirp
2 Chirps
Inactive
Active
Siren/ Horn Output (441 series ONLY)
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)
2 - Press & release transmitter buttons in the following sequence
#3-#2 then #1
3 - The siren will respond with the following:
1 Chirp
2 Chirps
Siren
Horn
Reset System
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)
2 - Press & release transmitter buttons in the following sequence
#3-#3 then #3
3 - The siren will respond with the following:
3 Chirps
System Reset
NOTE: Repeat sequence to change selection
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL MANUAL
PAGE 10
REMOTE VEHICLE SECURITY
Transmitter Programming
Follow the steps below to program the transmitters to the system s memory
Step 1 - Turn the Ignition key ON then OFF - Leaving Key Off.
Step 2 - Press and release the Program Button twice then press and hold.
Step 3 - The siren will respond with five chirps to confirm Transmitter Program Mode.
Note: If the siren does not respond, repeat Steps1&2
Step 4 - Continue to hold the Program Button and press lock button on each of the
transmitter’s to be programmed(Maximum of 3 Different transmitter codes).
Step 5 - The system will respond with a siren chirp each time a transmitter is programmed.
Exit - After five seconds the system will exit transmitter program mode automatically.
NOTE: You must program ALL of the transmitters to be used at one time. For the owner’s
security any transmitters not programmed at this time will be erased from memory.
*** This system will store a maximum of three transmitter codes in memory.
Car Jack Mode Activation (CJ series ONLY).
1) If the ignition key is On and a door is opened the Car Jack Mode
Timer will start. The siren will chirp one every second for 10
seconds then trigger into full alarm.
2) If the timer was activated by accident, within 10 seconds turn the
ignition key back to On then press and release the program
button one time. The Car Jack Mode Timer will stop.
3) If the timer is not deactivated Car Jack Mode will trigger into full
alarm. To deactivate turn the ignition On, then press and release
the program button 5 times then press unlock on the remote
transmitter.
Emergency Override.
If Car Jack Mode is not deactivated in time, the system will need to
be placed into Emergency Override. Turn the ignition key to the On
position then press and hold the program button for 20seconds. At
this time the customer can bring the vehicle back to the dealer for a
system reset.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE VEHICLE SECURITY
INSTALL MANUAL
PAGE 11
Alarm Functions
Arm
1. Press and release the button.
2. The park lights will flash and the siren will chirp one time.
3. The doors will lock (optional).
NOTE: The LED will start flashing within five seconds. If installed, the starter
disable will activate.
Disarm
1.Press and release the button on the remote transmitter.
2.The park lights will flash and the siren will chirp two times.
3.The doors will unlock (optional).
NOTE: The LED will stop flashing. If installed, the starter disable will deactivate.
Silent Arm/Disarm
1. Press and release the button then press and release the button to
silent arm. The park lights will flash once to confirm.
2. Press and release the button then press and release the button to
silent disarm. The park lights will flash twice to confirm.
Panic
1. Press and hold the button on the remote transmitter.
2. The park lights will flash and the siren will sound.
3. Press and release the or the button to deactivate*.
*Panic will be active for 60 seconds or until disabled by the remote transmitter.
Trunk
1. Press and hold the button for 3 seconds.
2. The doors will unlock (optional), continue holding until the Trunk Release
activates.
Car Finder
1. Press and hold the button for 3 seconds.
2. The park lights will flash and the siren will chirp 5 times.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL MANUAL
PAGE 12
REMOTE VEHICLE SECURITY
Relay Wiring Diagrams
Negative Type Door Locks
Positive Type Door Locks
87
87
87a
86
87a
86
85
85
30
30
5 Wire / Reverse Polarity Type Door Locks
87
87a
87
87a
86
86
85
85
30
30
Negative Park Lights- In some cases the park lights may flash erratically after
installing the negative park light relay. To correct this issue add a diode between the coil
pins of the relay as shown.
Ground
Add IN4001 Diode
as shown
87
87a
86
85
White
30
Negative park light output
Download from Www.Somanuals.com. All Manuals Search And Download.
|