UltraATA 133 PCI
Quick Installation Guide
Introducing the UltraATA 133 PCI
The UltraATA133PCIis an ultra high-speed dualchannel
Ultra ATA/ 133 controller board for use in Pentium-class
computer.
Features and Benefits
•
•
•
Compliant with UltraDMA6ATA/ 133specifications
Compliant with PCI v2.2 Plug-n-Play
Provides two independent Ultra ATA channels
(built-in 256-byte FIFOs per channel)
•
•
•
Full ACPI power management support
Supports Ultra DMA 0-6 and Multi-word DMA 0-2
Breaks the 137GB barrier! Supports hard drives
larger than 137GB
•
•
Coexists with on-board controller
CRC (Cyclical Redundancy Check) error-checking
provides data verification and achieves flawless
data tranfer
•
•
•
Flash BIOS for easy upgrade
Achieves burst data transfer rates up to 133MB/ sec
Works with various brand,capacity hard disk drives
and ATAPI devices
System Requirements
•
•
Pentium-class computer with an available PCI slot
Windows 98SE/ ME/ NT 4.0/ 2000/ XP/ Server 2003
1
04-0233D
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the back of the
computer.
3. Remove your computer’s cover.
4. Remove the slot bracket from an available PCI slot.
5. To install the card, carefully align the card's bus
connector w ith the selected PCI slot on the
motherboard. Push the board down firmly, but
gently, until it is well seated.
6. Replace the slot bracket's holding screw to secure
the card.
Device Connection
The UltraATA 133 PCI is a dual channel Ultra ATA/ 133
controller that supports up to four IDE hard disk drives
or ATAPI devices. If you plan to use the second IDE
channel (IDE2).
In order to achieve high-speed data transfer, a 40-pin/ 80-
wire Ultra ATA ribbon cable is recommended. Also, do
not mix Ultra ATA/ 133 hard disk with slower IDE or
ATAPI devices on the same channel.
1. Install hard disk drive(s) in chassis.
2. Attach one connector on the long end of the Ultra
ATA ribbon cable to the board's IDE connector and
the other connector(s) to your IDE drive(s). Make
sure pin 1 on the cable (indicated by the colored
stripe) matches pin 1 on the board's IDE connector
and your IDE drive(s).
3. When two drives are installed on the same IDE
channel, make sure one drive is set up as Master and
the other as Slave. This rule applies to both IDE
channels.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4. The Ultra ATA ribbon cable has two connectors. If
you install only one drive, connect it to the end
connector of the cable. On the other hand, if you
install two drives, connect the master drive to the
end connector of the cable and the slave drive in the
middle connector.
Figure 2. Connecting the cable
5. Reconnect the system power and other peripherals
to your computer.
Driver Installation
This section provides information on how to install the
UltraATA 133 PCI drivers for the following operating
systems:
Windows 98SE........................................................... page 5
Windows ME ............................................................. page 6
Verify Windows 98SE/ ME Installation ..............page 6-7
Windows NT 4.0 ....................................................... page 7
Verify Windows NT 4.0 Installation ...................... page 8
Windows 2000 ........................................................... page 8
Windows XP/ Server 2003 ....................................... page 9
Verify Windows 2000/ XP/ 2003 Installation ...... page 10
Bios Configuration .................................................. page 10
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 98SE
For New Windows 98SE Installation
1. Install the board and follow Microsoft procedures to
install Windows 98SE accordingly.
2. Once Windows has been installed, right click My
Computer and click Properties. Select Device
Manager tab.
3. Double click PCI Mass Storage Controller listed
under Other Devices.
4. Select Driver tab, then click Update Driver button.
5. Insert the driver diskette and click Next.
6. Select Search for a better driver ... and click Next.
7. Check Floppy disk drives, uncheck the other boxes,
then click Next. Click Next again, then Finish.
8. Remove the driver diskette and restart Windows to
complete driver installation.
For Existing Windows 98SE Installation
1. Install the board and boot up Windows 98SE.
2. At the Add New Hardware Wizard, click Next.
3. Select Search for the best driver for your device and
click Next.
4. Insert the driver diskette, check Floppy disk drives,
uncheck the other boxes, then click Next.
5. Click Next, then Finish.
6. Remove the driver diskette and restart Windows to
complete driver installation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows ME
For New Windows ME Installation
1. Installthe board and follow Microsoft procedures to
install Windows ME accordingly.
2. Once Windows has been installed, right click My
Computer, then click Properties. Select Device
Manager tab.
3. Double click PCI Mass Storage Controller listed
under Other Devices.
4. Select Driver tab, then click Update Driver button.
5. Insert the driver diskette, select Automatic search
for a better driver (Recommended),then click Next.
6. Click Finish, remove the driver diskette and click
Yes to restart Wind ow s to com p lete d river
installation.
For Existing Windows ME Installation
1. Install the board and boot up Windows ME.
2. At the Add New Hardware Wizard,insert the driver
diskette.
3. Select Au tom atic search for a b etter d river
(Recommended), then click Next.
4. Click Finish.
5. Remove the driver diskette and restart Windows to
complete driver installation.
To Verify Windows 98SE/ME Installation
1. Right-click My Computer, then click Properties.
Select Device Manager tab.
2. Double click SCSI Controllers, an entry, Silicon
Image SiI 0680ATA/133Controller should be listed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. H ighlight Silicon Im age SiI 0680 ATA/133
Controller and click Properties. A message This
device is working properly is displayed in the dialog
box, the driver has been correctly installed. If any
error message is displayed, remove Silicon Image
SiI 0680ATA/133Controller and restartyour system.
Windows NT 4.0
For New Windows NT 4.0 Installation
1. Installthe board and follow Microsoft procedures to
install Windows NT 4.0 accordingly.
2. At the Windows NT Setup screen, press F6 to
specify and add the driver.
3. Press S, select Other, then press Enter.
4. Insert the driver diskette and press Enter.
5. Select Silicon Image SiI 0680 ATA/133 Controller
and press Enter.
6. Press Enter to continue and follow on-screen
instru ctions to com p lete Wind ow s N T 4.0
installation.
For Existing Windows NT 4.0 Installation
1. Install the board and boot up Windows NT 4.0.
2. Double click My Computer/ Control Panel/SCSI
Adapters, then click the Drivers tab.
3. Click Add… then Have Disk....
4. Insert the driver diskette, type in A:, then click OK.
5. H ighlight Silicon Im age SiI 0680 ATA/133
Controller and click OK.
6. Click OK, remove the driver diskette and restart NT
to complete driver installation.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
To Verify Windows NT 4.0 Installation
1. Double click My Computer/Control Panel/SCSI
Adapters.
2. H ighlight Silicon Im age SiI 0680 ATA/133
Controller from SCSI Adapters listing and click
Properties. A message This device is working properly
is displayed in the dialog box, the driver has been
correctly installed.
Windows 2000
For New Windows 2000 Installation
1. Installthe board and follow Microsoft procedures to
install Windows 2000 accordingly.
2. Restart your system w hen prompted d uring
Windows' installation.
3. At the Windows 2000 Setup screen, press F6 to
install the driver.
4. Insert the driver diskette. Press S, then press Enter.
5. Select Silicon Image SiI 0680 ATA/133 Controller
and press Enter.
6. Press Enter to continue and follow on-screen
instructions to complete installation.
For Existing Windows 2000 Installation
1. Install the board and boot up Windows 2000.
2. At the Found New Hardware Wizard, click Next.
3. Select Search for a suitable driver for my device
(recommended) and click Next.
4. Insert the driver diskette, check Floppy disk drives,
uncheck the other boxes, and click Next. Click Next
again to continue.
5. Click Finish, remove the driver diskette and restart
Windows to complete driver installation.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows XP/Server 2003
For New Windows XP/Server 2003 Installation
1. Installthe board and follow Microsoft procedures to
install Windows XP accordingly.
2. Restart your system w hen prompted d uring
Windows' installation.
3. At the Windows Setup screen, press F6 to install the
driver.
4. Insert the driver diskette. Press S then press Enter.
5. Select Silicon Image SiI 0680 ATA/133 Controller
and press Enter.
6. Press Enter to continue and follow on-screen
instructions to complete Windows XP installation.
7. When the Software Installation warning pops up,
click Yes. And when the Hardware Installation
warning pops up, click Yes again.
For Existing Windows XP/Server 2003 Installation
1. Install the board and boot up Windows XP.
2. At the Found New Hardware Wizard, insert the
d river d iskette, select In stall th e softw are
automatically (Recommended), then click Next.
3. Click Finish, remove the driver diskette and restart
Windows to complete the installation.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
To Verify Windows 2000/XP/2003 Installation
1. Right click My Computer and click Manage.
2.
Select Device Manager.
3. Double click SCSI and RAID Controllers, then
double click Silicon Image SiI 0680 ATA/133
Controller to display driver properties.
4. A message Thisdeviceisworkingproperlyis displayed
in the dialog box, the driver has been correctly
installed.
Bios Configuration
The UltraATA 133 PCI BIOS will appear everytime your
system starts up. If the bios doesn't show, please try your
controller in another PCI slot. During this (Post) process,
the bios will show up and indicate the devices attached to
it.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support and Warranty
Q UESTIO N S?
SIIG’s O n lin e Su p p ort has answ ers!
Simply visit our website at www.siig.com and click on Support.
Our online support database is updated daily with new drivers
and solutions. Answers to your questions could be just a few clicks
away. You can also submit questions online and one ofour technical
support analysts will promptly respond.
A lifetime manufacturer warranty supplied with this product is
offered by SIIG, Inc. Please see SIIG website for more warranty
details. If you should happen to encounter any problems with this
product, please follow the procedures below.
If it is within the store's return policy period, please return the
product to the store where you purchased from.
If your purchase has passed the store's return policy period, please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective,an RMA number willbe issued. SIIG RMA department
can also be reached at (510)413-5333.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping the product to
SIIG at the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538
RMA #:
• SIIG will ship the repaired or replaced product via Ground
in the U.S and International Economy outside of the U.S at
no cost to the customer.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading computer upgrade
manufacturer of I/ O connectivity products, including PCI & ISA
serial and parallel ports, USB, Serial ATA & UltraATA controllers,
FireWire (1394a/ b),Networking,Sound Cards,and other accessories.
SIIG is the premier one-stop source of upgrades.
SIIG products offer comprehensive user manuals,many user-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retailstores,mailorder catalogs,and e-commerce
sitesin theAmericasand theUK,aswellasthrough major distributors,
system integrators, and VARs.
PRODUCT NAME
UltraATA 133 PCI
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Ave.
Fremont, CA 94538-3152
UltraATA 133 PCI is a trademark of SIIG, Inc.
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are
registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel
Corporation. Other names used in publication are for identification only and may be trademarks
of their respective companies.
March, 2005
Copyright ©2005 by SIIG, Inc. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|