U Line Refrigerator 2275DWRCOL User Manual

INSTALL GUIDE

2000 SERIES DRAWER MODELS

REFRIGERATORS

COMBO® REFRIGERATOR/FREEZER/ICE MAKERS

WINE CAPTAIN® MODELS

2275DWRCS

2275DWRCOL

C2275DWROL

C2275DWRS

2275DWRW

The Built-In Undercounter Leader Since 1962

U-LINE.COM

Download from Www.Somanuals.com. All Manuals Search And Download.

2 Safety Precautions

General Precautions

Use this appliance for its intended purpose only and follow these

general precautions with those listed throughout this guide:

IMPORTANT

• PLEASE READ all instructions before installing,

operating, or servicing the appliance.

DANGER

RISK OF CHILD ENTRAPMENT. Before you throw away your

old refrigerator or freezer, take off the doors and leave shelves

in place so children may not easily climb inside.

• Proper installation procedures must be followed when

completing an installation or relocation of a unit.

Consult the installation guide before any installation

begins. U-Line contact information appears on the rear

cover of this guide.

WARNING

SHOCK HAZARD - Electrical Grounding Required.

• Never attempt to repair or perform maintenance on

the unit until the electricity has been disconnected.

• Never remove the round grounding prong from the

plug and never use a two-prong grounding adaptor.

• Altering, cutting of power cord, removal of power

cord, removal of power plug, or direct wiring can

cause serious injury, fire and or loss of property and

or life, and will void the warranty.

• This unit requires connection to a dedicated 15 Amp

grounded (three-prong), polarized receptacle, installed

by a qualified electrician, compliant with applicable

electrical codes.

Safety Alert Definitions

• Never use an extension cord to connect power to the

unit.

• Always keep your working area dry.

Throughout this guide are safety items labeled with a Danger,

Warning or Caution based on the risk type:

WARNING

DANGER

Install provided Anti-Tip kit on all Wine Captain

Models and Glass Door Refrigerators. Serious personal

injury could occur.

Danger means that failure to follow this safety statement will

result in severe personal injury or death.

CAUTION

WARNING

• Use care when moving and handling the unit. Use gloves

to prevent personal injury from sharp edges.

• If your model requires defrosting, DO NOT use an ice

pick or other sharp instrument to help speed up

defrosting. These instruments can puncture the inner

lining or damage the cooling unit. DO NOT use any type

of heater to defrost. Using a heater to speed up

defrosting can cause personal injury and damage to the

inner lining.

Warning means that failure to follow this safety

statement could result in serious personal injury,

property or equipment damage.

CAUTION

Caution means that failure to follow this safety statement

may result in minor or moderate personal injury, property

or equipment damage.

IMPORTANT

• Do not lift unit by door handle.

• Never install or operate the unit behind closed doors.

Be sure front grille is free of obstruction. Obstructing

free airflow can cause the unit to malfunction and will

void the warranty.

• Failure to clean the condenser every six months can

cause the unit to malfunction. This could void the

warranty.

• Allow unit temperature to stabilize for 24 hours before

use.

• Do not Block any internal Fans

Use only genuine U-Line replacement parts. Imitation

parts can damage the unit, affect its operation or

performance and may void the warranty.

U-Line Safety Precautions

Download from Www.Somanuals.com. All Manuals Search And Download.

Tools / Material Required

3 Inspect & Plan

•

Screwdrivers — slotted and Phillips head

(If installing a 3/4” Full Overlay panel)

•

3/4” overlay frame material

Cutting Tools

Product Registration

Drill & Drill Bits

(If installing 1/4” Panel Insert)

You have received a carton containing your U-Line Combo Drawer

Model Ice Maker/Refrigerator or U-Line Refrigerator with a

package inside containing a Use and Care Guide, a Product

Registration Card, water connection parts and Anti-Tip Kit.

Complete and mail the Product Registration Card or register

online at www.U-LineService.com. Once your unit is installed,

keep the Use and Care Guide and this Installation Guide in a safe

place for future reference.

•

1/4” thick door panel material

Cutting Tools

Exterior Cleaning

Overlay Models:

•

The drawers, grille and cabinet may be cleaned with a mild

detergent and warm water solution. Do not use solvent-based

or abrasive cleaners. Use a soft sponge and rinse with clean

water. Wipe with a soft, clean towel to prevent water spotting.

Models Covered

This installation guide covers the following models

Stainless Models:

U-2275DWRCOL-00

U-2275DWRCS-00

U-2275DWRWOL-00

U-2275DWRWS-00

U-C2275DWROL-00

U-C2275DWRS-00

•

Stainless steel models can discolor when exposed to chlorine

gas, pool chemicals, salt water or cleaners with bleach.

•

Keep your stainless steel unit looking new by cleaning with a

good quality all-in-one stainless steel cleaner/polish on a

monthly basis. For best results use Claire Stainless Steel Polish

and Cleaner, which can be purchased from U-Line Corporation.

(The part number is 173348.) Comparable products are

acceptable. Frequent cleaning will remove surface

Inspection

Inspect the unit on a flat, level surface capable of supporting it’s

entire weight.

contamination that could lead to rust. Some installations may

require cleaning on a weekly basis.

Removing Protective Coating

All Models:

•

Do not clean with steel wool pads.

The protective coating covering the inside of the top drawer must

be removed before using.

Do not use cleaners that are not specifically intended

for stainless steel (this includes glass, tile and counter

cleaners).

Stainless Steel Models:

•

If any surface discolors or rusting appears, clean it quickly with

Bon-Ami or Barkeepers Friend Cleanser and a non-abrasive

cloth. Always clean in the direction of the grain. Always finish

this process with Claire Stainless Steel Polish and Cleaner or

comparable product to prevent further problems.

When inspecting/installing a Stainless Steel unit, the protective

coating covering the drawer fronts must be removed. Start at a

corner of the drawers and pull back the protective coating to

remove it from the drawer fronts.

•

Use of abrasive pads such as Scotchbrite will cause the

graining in the stainless to become blurred.

After all the protective coating has been removed from the

drawers, clean all Stainless Steel surfaces with Claire Stainless Steel

Polish and Cleaner or comparable product or a mild detergent and

warm water solution and soft cloth. Do NOT use abrasive cleaning

agents.

•

Rust that is allowed to linger can penetrate into the surface of

the stainless steel and complete removal of the rust may not be

possible.

If cleaning with mild detergent and warm water solution and soft

cloth, the unit MUST be treated with Claire Stainless Steel Polish

and Cleaner or comparable product to prevent discoloration.

WARNING

Rust that is allowed to linger can penetrate into the

surface of the stainless steel and complete removal of

the rust may not be possible.

U-Line Inspect & Plan

Download from Www.Somanuals.com. All Manuals Search And Download.

4 Prepare Site

Your U-Line product has been designed for either free-standing or

built-in installation. When built-in, your unit does not require

additional air space for top, sides, or rear. However, the front grille

must NOT be obstructed and clearance is required for an

electrical connection in the rear.

C2275DWR Series

IMPORTANT

• Unit can NOT be installed behind a closed cabinet door.

24"

34-1/4"

35-1/8"

WARNING

SHOCK HAZARD — Electrical Grounding Required.

•

Never remove the round grounding prong from the

plug and never use a two-prong grounding adapter.

1-1/2"

24-1/4"

Never use an extension cord to connect power to the

unit.

Follow the cut-out drawing The 24-1/4" width allows 1/4" for ease

in installation and removal of the unit. 24" is the cabinet depth in

most installations.

IMPORTANT

Electrical installation must observe all state and local

codes. This unit requires connection to a grounded (three-

prong), polarized receptacle that has been placed by a

qualified electrician.

2275DWRW Series

The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A

power supply (normal household current). An individual, properly

grounded branch circuit or circuit breaker is recommended. GFCI

(ground fault circuit interrupter) is usually not required for fixed

location appliances and is not recommended for your unit because

a GFCI could be prone to nuisance tripping. However, be sure to

consult your local codes.

24"

See below for recommended receptacle location & cut out

dimensions

34-1/4"

35-1/8"

2275DWRC Series

1-1/2"

24-1/4"

Follow the cut-out drawing The 24-1/4" width allows 1/4" for ease

in installation and removal of the unit. 24" is the cabinet depth in

most installations.

24"

34-1/4"

35-1/8"

1-1/2"

24-1/4"

Follow the cut-out drawing. The 24-1/4" width allows 1/4" for ease

in installation and removal of the unit. 24" is the cabinet depth in

most installations.

Prepare Site

Download from Www.Somanuals.com. All Manuals Search And Download.

C2275DWR & 2275DWRC

5 Product Dimensions

2275DWRW

2275DWRC

23-15/16”

24"

23-1/4"

23-1/4”

33-7/8”

3-7/8”

Black

Overlay

24"

23-3/8”

C2275DWR

24"

23-1/4"

33-7/8"

33-7/8”

3-7/8”

Stainless Steel

2275DWRW

3-7/8”

Black

24"

23-15/16”

23-3/8”

33-7/8"

33-7/16”

3-7/8”

Stainless Steel

Stainless

Product Dimensions

Download from Www.Somanuals.com. All Manuals Search And Download.

Other Site Requirements

6 Clearance Information

Power Supply

The unit must be installed in a wall or under a counter-top to allow

for the installation of the Anti-Tip Kit (see Page 14).

The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A

circuit (normal household current). See Electrical Specifications.

WARNING

Water Supply

The unit requires a 1/4-inch OD water supply line and a shut-off

valve. For more information see Page 12.

The Anti-Tip Kit must be installed on this unit before it

is used. Never use the drawers as steps or as a shelf to

support more than the drawers’ contents. Serious

personal injury could occur.

Environmental Requirements

The units are designed to operate between 50°F (10°C) and 100°F

(37°C). High ambient temperatures (100°F [37°C] or higher) may

reduce the unit’s ability to reach low temperatures and may also

reduce the ice production rate for those models with icemakers.

The unit is designed so it can be installed next to a wall on either

side.

If the ambient temperature is expected to drop below 45°F (7°C),

drain all water from the unit to prevent freezing damage, which is

not covered by the warranty.

For best performance, keep the unit out of direct sunlight and away

from heat generating equipment.

For best performance and life outdoors, place under a counter or

provide shelter of some kind.

In climates where high humidity and dew points are present,

condensation may appear on outside surfaces. This is considered

normal. The condensation will evaporate when the humidity drops.

Cabinet

or Wall

The drawer unit can be installed with an appliance or fixture

located in front of it, as long as there is adequate clearance for the

drawer to be opened and removed when servicing.

U-Line recommends you consider additional clearance in front of

the open drawer for convenience.

24" Min.

Door Swing Dimensions

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT

7 Standard Drawers

Drawer adjustments are made by moving the slide that carries the

drawer’s rail. Minor adjustments may be made by loosening one of

the slide’s mounting screws, adjusting the slide and retightening the

screw. Severe adjustments may be made by removing the slides’

mounting screws, drilling new mounting holes and remounting the

slide.

Checking Drawer Alignment

The unit’s drawers are aligned at the factory before shipment.

However, their alignment could have been disturbed during

shipment or during overlay panel installation. Check each drawer

to confirm that it is aligned:

Side-to-Side Adjustment

The drawer will need a Side-to-

Side Adjustment if, when viewed

from the top, the drawer front is

not square with the sides of the

cabinet. This is caused by one of

Aligned

Front-to-Back

Aligned

Side-to-Side

Not Aligned Side-to-Side

the slides being mounted too far

forward on the unit’s liner.

Top View of Unit

Minor Adjustment:

Note: The mounting holes on the

Loosen

slide are slightly larger than the

Mounting Screws

screws’ diameter.

Aligned

Top-to-Bottom

1. Loosen the slide’s mounting

screws.

2. Push the slide backward.

•

Side-to-Side — When viewed from the top, the drawer front

should be square with the sides of the cabinet.

3. Retighten the screws.

Push Slide

Backward

Front-to-Back — When viewed from the side, the drawer

front should be straight with the cabinet’s sides, not cocked

forward or back.

Severe Adjustment:

Note: The slides have extra

mounting holes that may be used.

•

Top-to-Bottom — When viewed from the front, the drawer

should be level horizontally.

Mark and Drill New

Mounting Holes

1. Remove the slide’s mounting

screws.

Adjusting Drawer Alignment

2. Reposition the slide so it is the

same distance from the front

of the liner as the other slide.

Measure to confirm.

WARNING

SHOCK HAZARD — The unit must be unplugged from

the wall outlet during drawer removal, adjustment and

re-installation.

Push Slide

Backward

3. Mark new drilling holes using

different sets of mounting holes on the slide.

Drawer Removal

Note: Front location holes are shown. Corresponding rear holes

will also need to be marked.

Mounting

Screw

1. Confirm that the unit is

unplugged from wall outlet.

4. Drill all the new holes with a #30 drill bit.

2. Unplug the drawer’s connection

wiring (top drawer only).

5. Remount the slide.

Not Aligned Front-to-Back

Front-to-Back Adjustment

3. Remove the mounting screws.

The drawer will need a Front-to-

Back Adjustment if, when viewed

from the side, the drawer front is

cocked forward or back. This is

caused by the front slide

4. Pull the drawer completely out

of the unit.

CAUTION

mountings not being level with

the rear slide mountings.

Use care when handling the drawer. Drawer edges, drawer

rail and the unit’s slide may be sharp.

Side View of Unit

U-Line Drawer Alignment

Download from Www.Somanuals.com. All Manuals Search And Download.

Minor Adjustment:

Screws Should

Be Loose

Note: The mounting holes on the

slide are slightly larger than the

screws’ diameter.

Note: The mounting holes on the slide are slightly larger than the

screws’ diameter.

1. Loosen one slide’s mounting

screws.

Mounting Screws

1. Loosen one slide’s mounting

screws.

2. Push the slide upward or

downward to match the

position of the other slide.

2. Level the slide.

3. Retighten the screws. See

Figure 18.

Level the Slide

Push Slide

Upward or

Downward

3. Retighten the screws.

4. Repeat procedure for the

other slide. Measure to

confirm.

3. Reposition the slide so it is

level.

4. Mark new front drilling holes

using a different set of

Level the Slide

3. Mark new drilling holes using

different sets of mounting

holes on the slide. See Figure

22.

Push Slide

Upward or

Downward

mounting holes on the slide.

5. Drill the new holes with a #30 drill bit.

6. Remount the slide.

Note: Front location holes are shown. Corresponding rear holes

will also need to be marked.

7. Repeat procedure for the other slide.

4. Drill all the new holes with a #30 drill bit.

5. Remount the slide.

Top-to-Bottom (and Left-to-Right) Adjustment

Re-installation of Drawer

CAUTION

Not Aligned

Top-to-Bottom

Use care when handling the drawer. Drawer edges, drawer

rail and the unit’s slide may be sharp.

Not Aligned Left-to-Right

1. Set the drawer’s rails onto the slides.

2. Re-install the rails’ mounting screws. See Figure 13 on Page 10.

3. Plug in the drawer’s connection wiring (top drawer only).

FrontView of Unit

TopView of Unit

The drawer will need a Top-to-Bottom Adjustment if, when viewed

from the front, the drawer is not level horizontally. Viewed from

the top, one side will protrude. This is caused by one of the slides

being mounted higher than the other slide on the unit’s liner.

U-Line Drawer Alignment

Download from Www.Somanuals.com. All Manuals Search And Download.

Full Overlay Drawer Panels

8 Drawer Panel Installation

Drawer Panel Preparation

Custom 1/4" Drawer Panel Inserts

Full overlay drawer panels completely cover the drawer fronts and

handles to give a built-in appearance. Overlay units are shipped

ready for Full Overlay installation.

Drawer Panel Preparation

Custom drawer panels can be inserted into the drawer fronts.

Custom drawer panels can be flat or raised, as long as the

maximum panel thickness where inserted into the drawer front

reveal (channel) is 1/4"-thick. For raised panels, the depth of the

reveal is 1/4" on all four sides.

Note: For standard installations, both drawers mount the same and

a 1/2" gap is achieved between drawers.

Cut the overlay to the following dimensions.

Full Overlay Dimensions:

Width:23-3/4"

IMPORTANT

Height:14-3/4"

Raised panels will reduce the drawer’s front clearance if

the unit is installed facing an appliance or structure (see

Page 5).

IMPORTANT

The thickness of the wood overlay panel must be 3/4". The

door panel must not weigh more than 20 lbs.

Cut the panel inserts to the following dimensions.

Custom 1/4" Dimensions:

Drawer Panel Installation

Width:23-1/32"

Removing Existing Drawer Fronts

Height:12-15/32"

1. Open drawer. Pull drawer gasket out of groove (top edge of

drawer only). Start in the middle and pull outward, moving

toward the edge (see below). This may take some force.

The door panels must not have a total weight of more than 20 lbs.

Drawer Panel Installation

2. Remove and save the two screws (

1) located at the ends of the

Install the insert as follows:

handle. Remove the handle.

CAUTION

Handle

Screw

Gasket

Use care when handling the insert. Insert edges may be

sharp.

1. Open drawer. Pull drawer gasket

out of groove (top edge of drawer

only). Start in the middle and pull

outward, moving toward the edge .

This may take some force.

Handle

Screw

Gasket

2. Remove and save the two outside

screws.

3. Remove the original handle and

discard.

4. Remove and discard existing panel

and cardboard spacer.

3. Remove existing panel and cardboard spacer. Discard the spacer.

5. Slide custom drawer panel insert

into 1/4-inch channel in drawer

front.

6. Holding drawer gasket out of the

way, replace handle on drawer,

Standard

Handle

making sure it is seated properly on

insert and that screw holes line up.

Full Handle

7. Install two small screws removed in

Step 2.

8. Starting at the corners and working

inward, push drawer gasket into

place on drawer.

U-Line Drawer Panel Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Attaching the Full Overlay Panel

CAUTION

1. If user-supplied cabinet handles will be used, attach their

hardware to the overlay panel at this time.

It is important to ensure that all drilled holes are drilled to

the correct depth in order to avoid splits in the wood

when hardware is installed.

IMPORTANT

User-supplied cabinet handles MUST be counter bored to

make sure mounting hardware is below surface of overlay

panel. Failure to do so can cause damage to overlay panel

and/or drawer. Overlay panel will not sit flush to drawer if

mounting hardware is not counter bored.

4. Remove tape adjoining the panels and enlarge the five holes in

the overlay panel using a 0.201" (#7) drill.

5. Attach the drawer panel to the overlay panel using #10 x 5/8"

wood screws and nylon spacers. The nylon spacers fit between

the overlay panel and the door panel as shown in Figure 11. The

spacers allow the original drawer panel to slide back into the 1/

4"-thick drawer front reveal (channel).

Tape

Back of

Wood

Panel

Drawer Panel

Typical

Wood Panel

Drawer Panel

#10 5/8"

Side of

Wood Panel

Round Head Screw

Five Required

Bottom of

Wood Panel

11/32"

Bottom

3/8"

Both Sides

Plastic

Spacer

Five

2. Place and tape the existing drawer panel on the back of the

overlay panel (see above).

Required

3. Drill the five holes (5/32" drill 3/8" deep) through both panels

according.

Top of

Wood Panel

Vinyl Coated

Steel Panel

IMPORTANT

Drawer panel and overlay panel must be aligned properly

or the drawer will not operate correctly.

2-15/16"

Assembling the Drawer Front

1. Install the assembled panel by sliding the original door panel

back into the drawer front.

14-3/4"

5/32" x 3/8" Deep –

5 Places

11-13/16"

2. Replace the handle assembly and secure with the two screws

removed in Step 2 under Removing Existing Drawer Fronts.

3. Starting at the corners and working toward the center, push the

drawer gasket back into place. Go on to 5 Adjust Drawers.

11-7/8"

23-3/4"

U-Line Drawer Panel Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

You may also mount your overlay to your grille using hook and

loop type fasteners. U-Line recommends using 3M® Dual lock®

fasteners. To mount your overlay using a hook and loop fastener

follow the instructions below.

9 Wood Grille Overlay

Grille Overlay

1. Read the instructions provided with your hook and loop

fastener carefully.

Your models grille is designed to accept a wood grille over-

lay. An overlay may be used to compliment a door overlay

and provides a seamless look for your surrounding decor.

Follow the instructions below to prepare and install your

grille overlay. Be sure to read over this chapter completely

before beginning.

2. Apply hook and loop fastener system to the back of the overlay

and front of the grille. Use the shaded areas in the diagram

below for application location.

24 Inch Models

Application

Preparation

WARNING

Area

Wood Overlay

Back

The grille overlay MUST have venting as shown in the

drawing below. Failure to have proper venting can

result in damage to your model.

Grille

Front

WARNING

The grille overlay may only be installed on indoor units.

3. Carefully align the wood overlay with the grille and press into

position.

1. Prepare your overlay using the dimensions provided in the

figure on page 11. If using a hook and loop style mount, drill

hole A will not be used.

2. If desired, stain and finish your grille to match your surrounding

decor. Follow the stain manufacturers instructions to apply stain

to your overlay.

Installation

IMPORTANT

The wood overlay grille must be installed in such a

manner that the grille assembly can still be removed from

the unit.

Screw Mount (Recommended)

1. Remove the grille from your unit by removing the two

mounting screws. See below.

Remove Screw

2. Lay the back of your grille overlay onto the front of the grille.

Make certain the screw holes and vents are aligned.

3. Slide each of the screws removed in step 1 through the grille

overlay and grille.

4. Mount your new overlay onto your unit by screwing the overlay

back onto the base of your unit.

Hook and Loop Fastener Mount

U-Line Grill Overlay Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Grille Drawing

U-Line Grill Overlay Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

10 Prepare Plumbing

10 Level The Unit

Leveling Information

CAUTION

Note: It is recommended that the unit is level.

Plumbing installation must observe all state and local

codes. All water and drain connections MUST BE made by

a licensed/qualified plumbing contractor. Failure to follow

recommendations and instructions may result in damage

and/or harm.

1. Use a level to check the

levelness of the unit

from front to back and

from side to side. Level

should be placed along

top edge and side edge

as shown (see Figure

24).

Water Supply Connection

When connecting the water supply, follow these guidelines:

2. If the unit is not level,

adjust the feet on the

corners of the unit as

necessary.

•

Review the local plumbing codes before you install the unit.

Connect to the cold water supply.

The water pressure should be between 20 and 120 psi.

The water line MUST have a shut-off valve in the 1/4” O.D.

supply line.

3. Check the levelness

after each adjustment

•

Leave approximately 8’ of water line to be coiled behind the

appliance. The water line should be looped into 2 coils. This

will allow the unit to be removed for cleaning and servicing.

However, make certain that the tubing is not pinched or

damaged during installation.

and repeat the previous

steps until the unit is level.

IMPORTANT

U-Line requires the use of copper tubing, or U-Line water

line hook up kit (U-MPWATERHOOKUP) for installation.

Do not use any plastic water supply line. The line is under

pressure at all times. Plastic may crack or rupture with

age and cause water damage to your home.

To connect to water supply:

1. Locate the desired cold water

supply location. Attach a 1/4”

copper line to this location

and route the tubing to the

appliance. Leave

Installation Tip

If the room floor is higher than the floor in the cut-out opening,

adjust the rear feet to achieve a total unit rear height of 1/8" less

than the opening’s rear height. Shorten the unit height in the front

by adjusting the front feet. This allows the unit to be gently tipped

into the opening. Readjust the front feet to level the unit after it is

correctly positioned in the opening.

approximately 8’ of water line

to be coiled behind the

appliance. The water line

should be looped into 2 coils.

This will allow the line to flex

when removing the unit for

cleaning and servicing.

2. Locate the U-Line supplied garden

hose fitting. Ensure the end of the

9/16"Wrench

copper tubing has been cut straight

and free of burrs. Slide the

compression nut and ferrule onto

1/4" CopperWater

Supply Line

the copper tubing as shown. Push

the assembly completely into the

garden hose fitting and tighten

using the two wrenches.

7/16"Wrench

FromWater Supply

to Ice Maker

U-Line Electrical / Plumbing Specfications

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Insert the screws through the anti-tip bracket (B) and attach the

bracket to the unit. Tighten screws securely.

11 Install Unit

3. Repeat for the other side.

1. Plug in the power cord.

Note: The bracket should be flush with the surface it is being

attached to. If it is not, loosen the screws and slide the bracket

against the mounting surface. Tighten screws securely.

2. Open the top drawer and press the POWER icon to turn the

unit OFF

3. C2275DWR Only: Open the water supply valve in the main

4. Using two of the screws (C) supplied, fasten the screws through

the bracket and into the counter, cabinet or wall.

water source.

4. Gently push the unit into position. Be careful not to entangle the

electrical cord.

IMPORTANT

Certain cabinets or countertops may require special

fasteners or additional wood blocking to anchor properly.

5. Re-check the leveling, from front to back and side to side. Make

any necessary adjustments. The unit’s top surface should be

approximately 1/8" below the countertop.

CAUTION

Anti-Tip Kit Installation

Make sure the screws are back far enough so they do not

damage any exposed front surface of the cabinet.

WARNING

Installation Troubleshooting

• The Anti-Tip Kit must be installed on this unit before

it is used.

Problem

• Additional blocking or special fasteners may be

required for installation. Installer is responsible for

secure attachment to prevent the unit from tipping.

• Make sure the mounting screws attaching the unit to

the counter, cabinet or wall are deep enough into the

mounting surface to support the weight of the

drawers and the items that will be inside the drawers.

• Never use the drawers as steps or as a shelf to

support more than the drawers’ content. Serious

personal injury could occur.

The drawer remains open unless it is pushed closed.

Solution

The drawer should be self-closing when it is open approximately

8". If it is not, re-check leveling from front to back of the unit and

readjust if necessary.

Problem

After leveling, the unit must be secured to a counter, a cabinet or a

wall to prevent tipping.

Water is leaking under the unit (C2275DWR units)

Solution

1. Open the upper drawer to expose the six screws (A) installed

at the top two corners (three at each corner). Remove the

appropriate screws for horizontal or vertical mounting Do not

discard.

A water leak under the unit is most likely caused by a bad

connection in the water supply line. Make sure the water line’s

brass fitting is screwed tight to its valve and threaded correctly.

Countertop orWall Header

Horizontal Mounting

(Left Side Shown)

Vertical Mounting

Cabinet orWall Stud

(Left Side Shown)

U-Line Electrical / Plumbing Specfications

Download from Www.Somanuals.com. All Manuals Search And Download.

First Time Start Up

All U-line units are shipped from the factory with controls that are

preset. No initial adjustments are required.

Once installation and leveling is complete, the unit is ready for

initial start-up and operation. Open the top drawer press and hold

the POWER icon on the display panel for aproximately ten

seconds until the °F symbol flashes and release.

U-Line recommends that the unit be allowed to run overnight

prior to loading the refrigerator with product.

Start-Up Troubleshooting

Problem

Unit does not appear to turn on POWER icon is pressed.

Solution

Make sure unit is plugged in and outlet has power (circuit breaker

has not tripped).

IMPORTANT

See the Use and Care Guide’s Troubleshooting Guide for