TXD series
USER MANUAL
Turbosound Ltd., Star Road, Partridge Green, West Sussex RH13 8RY UK
Tel: +44 (0)1403 711447 Fax: +44 (0)1403 710155
web: www.turbosound.com
Issue 1.3 July 2006
Copyright © 2006 Turbosound Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
Warranty Coverage................................................................................................................... 30
TXD series manual
page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
INTRODUCTION
Thanks
Thank you for choosing a TURBOSOUND TXD series loudspeaker product for your application.
Please spare a little time to read the contents of this manual, so that you can obtain the best
possible performance from this unit.
All TURBOSOUND products are carefully engineered for world class performance and reliability.
If you would like further information about this or any other TURBOSOUND product, please
We look forward to helping you in the near future.
Congratulations, you have just purchased a professional loudspeaker system from the renowned
Turbosound range, designed to give you the best in audio quality and many years of reliable,
trouble free operation. It offers superior audio quality, full technical documentation, and rigging
and flying hardware options. Please read through this manual carefully before you attempt to
operate the loudspeaker system. It contains valuable information enabling you to quickly and
easily set up and connect the loudspeakers, important system and set-up checks together with
positioning and mounting instructions.
Unpacking the TXD series loudspeaker
After unpacking the unit please check carefully for damage. If damage is found, please notify the
carrier concerned at once. You, the consignee, must instigate any claim. Please retain all
packaging in case of future re-shipment.
TXD series manual
page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
FEATURES
•
•
•
Superb audio quality: carefully designed and matched loudspeaker drive units are used
to give
you exceptional performance and many years of reliable, trouble free operation.
High quality loudspeaker components are used throughout the range. Low frequency
drivers are specified for high sensitivity and durability, while high frequency drivers are
selected for consistent and reliable performance.
High frequency protection system: two-stage thermal overload circuits operate on all
two-way products to prevent damage to the HF drive units from both transient peaks and
long term heating effects.
•
•
Professional appearance: TXD series enclosures are equally suited to live sound and DJ
applications as well as permanent installations.
Easy transportability: comfortable, ergonomic flush handles are provided on all TXD
series enclosures for easy lifting and transportation in mobile sound reinforcement
applications.
•
Wide dispersion: TXD series enclosures are designed to give wide and even dispersion
patterns in order to maximise sound coverage over a given area from single
loudspeakers.
•
•
Solid construction: all Turbosound TXD series cabinets are built from high grade, multi-
layer birch plywood and are finished in a durable semi-matt textured paint.
Integral rigging points: fitted as standard, enabling use with optional M10 shoulder
eyebolts for many types of fixed installations. TXD-081, TXD-121 and TXD-151 enclosures
can be permanently installed using Turbosound wall and ceiling brackets. All models are
type-tested for load rating to ensure safe rigging.
•
•
Pole mount and tripod stand use is facilitated by the provision of integral pole mount
fittings.
Speakon NL4MP connectors are fitted to all TXD series enclosures, enabling simple and
easy hook-ups as well providing loop-in / loop-out facilities to additional enclosures.
TXD series manual
page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
PRODUCT RANGE SUMMARY
TXD-081
The TXD-081 is a compact two-way loudspeaker recommended for portable speech and music
reinforcement in an easily transportable cabinet, as well as fixed installation applications requiring
professional quality background sound.
It is an all-passive design featuring an 8” low frequency driver and a 1” high frequency
compression driver on a 100ºH x 60ºV Converging Elliptical Waveguide™ HF horn. The drive units
are matched with an internal passive crossover network to ensure a seamless transition and these
are all housed in an optimally tuned trapezoidal birch plywood enclosure.
The compression driver is protected from accidental damage due to overdriving by an intelligent
protection circuit built into the crossover network which detects signal level, and automatically
attenuates should it approach or exceed potentially damaging levels.
The TXD-081 is equipped with internal rigging points for use with Turbosound wall and ceiling
brackets, and M10 eyebolts. A standard 35mm pole mount is fitted.
The rear panel carries dual Neutrik Speakon NL4MP speaker connectors for input and parallel
connections to an additional TXD series cabinet, or TXD series bass enclosures.
TXD-121
The TXD-121 is a compact trapezoidal passive two-way loudspeaker enclosure designed for use in
a wide variety of live sound, fixed installation and mobile DJ applications that require professional
sound quality in an easily transportable format.
It consists of a 12” reflex-loaded low frequency driver and a 1” high frequency compression driver
on a 70ºH x 40ºV dispersion HF horn in an optimally tuned trapezoidal enclosure. These high-
grade components are matched with an internal second order passive crossover network to
ensure a seamless transition between the HF and LF drivers.
The crossover incorporates a two stage thermal overload protection system which prevents
damage to the high frequency driver, reacting instantly to large transient peaks while still allowing
wide dynamic range to be maintained. Although the protection system is transparent at normal
operating levels, as the level increases the signal is gradually and imperceptibly compressed once
the critical threshold has been reached.
The cabinet is constructed from 15mm (5/8”) birch plywood, screwed and glued together for
maximum rigidity. A pole mount socket is fitted for use with optional 35mm poles and
loudspeaker stands. Two recessed flush handles are provided for easy lifting and carrying and
four rubber feet are fitted to the bottom of the cabinet. A grey powder-coated perforated steel
mesh grille protects the drivers from damage.
M10 rigging points are provided on the top and rear of the cabinet to enable it to be suspended
and angled in permanent installations using shoulder eyebolts. M8 rigging points are provided on
TXD series manual
page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
the rear of the cabinet for use with Turbosound wall and ceiling brackets. Two Neutrik Speakon
NL4MP speaker connectors are located on the rear panel, providing input and parallel connections
to additional TXD series cabinets or bass enclosures.
TXD-151
The TXD-151 is a trapezoidal passive two-way loudspeaker enclosure designed for use in a wide
variety of live sound, fixed installation and mobile DJ applications that require professional sound
quality in an easily transportable format.
It consists of a 15” reflex-loaded low frequency driver and a 1” high frequency compression driver
on a 70ºH x 40ºV dispersion HF horn in an optimally tuned trapezoidal enclosure. These high-
grade components are matched with an internal second order passive crossover network to
ensure a seamless transition between the HF and LF drivers.
The crossover incorporates a two stage thermal overload protection system which prevents
damage to the high frequency driver, reacting instantly to large transient peaks while still allowing
wide dynamic range to be maintained. Although the protection system is transparent at normal
operating levels, as the level increases the signal is gradually and imperceptibly compressed once
the critical threshold has been reached.
The cabinet is constructed from 15mm (5/8”) birch plywood, screwed and glued together for
maximum rigidity. A pole mount socket is fitted for use with optional 35mm poles and
loudspeaker stands. Two recessed flush handles are provided for easy lifting and carrying and
four rubber feet are fitted to the bottom of the cabinet. A grey powder-coated perforated steel
mesh grille protects the drivers from damage.
M10 rigging points are provided on the top and rear of the cabinet to enable it to be suspended
and angled in permanent installations using shoulder eyebolts. M8 rigging points are provided on
the rear of the cabinet for use with Turbosound wall and ceiling brackets. Two Neutrik Speakon
NL4MP speaker connectors are located on the rear panel, providing input and parallel connections
to additional TXD series cabinets or bass enclosures.
TXD-252
The TXD-252 is a trapezoidal active/passive full range loudspeaker enclosure, designed for use in a
wide variety of live sound, DJ and fixed installation applications.
It consists of two 500 watt (program) 15” low frequency drivers and a 3” coil compression driver
on a rotatable 80°H x 50°V Converging Elliptical Waveguide™, in an optimally tuned birch
plywood cabinet.
Two Speakon NL4MP speaker connectors are provided on the rear panel for input and link
connections when used in passive mode, as well as a third switchable Speakon which is used to
bypass the passive crossover when the cabinet is operated in bi-amplified mode. The internal
TXD series manual
page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
passive crossover network also protects the high frequency compression driver from being
overdriven.
The TXD-252 is ideal live music in bars and pubs, or for installing as a permanent system for pubs
and clubs. It can be suspended vertically, or horizontally with the HF horn rotated, using the M10
rigging points. Due to the trapezoidal cabinet shape it can be positioned close to a ceiling where
space is limited.
TXD-115
The TXD-115 is a front-loaded low frequency loudspeaker enclosure designed to give bass and
sub-bass reinforcement to TXD series 2-way enclosures in a wide variety of live sound
applications, as well as in fixed installations ranging from cafes, pubs, bars and restaurants to
retail stores and houses of worship.
It consists of a reflex-loaded 15” low frequency driver in an optimally tuned rectangular enclosure.
The TXD-115 includes a low-pass crossover network which filters high frequency signals from the
bass driver when used in conjunction with 2-way enclosures such as the TXD-121 or TXD-151,
enabling a full range system to be powered from a single amplifier channel without the need for
external electronic crossovers.
The enclosure is fitted with internal M10 threaded rigging points on the top and rear, which allow
single cabinets to be suspended and angled in fixed installations using optional M10 shoulder
eyebolts.
The cabinet is constructed from 15mm (5/8”) birch plywood, and is finished in a durable semi-matt
textured TurboBlue™ paint. Two flush handles are provided on the sides for easy lifting and
carrying, and four rubber feet are fitted to the bottom of the cabinet. Two Neutrik Speakon NL4MP
connectors provide input and parallel connections to additional TXD series cabinets.
TXD-215
The TXD-215 is a front-loaded low frequency loudspeaker enclosure designed to give bass and
sub-bass reinforcement to TXD series 2-way enclosures in a wide variety of live sound
applications, as well as in fixed installations ranging from cafes, pubs, bars and restaurants to
retail stores and houses of worship.
It consists of two reflex-loaded 15” low frequency drivers in an optimally tuned rectangular
enclosure. The TXD-215 includes a low-pass crossover network which filters high frequency
signals from the bass driver when used in conjunction with 2-way enclosures such as the TXD-121
or TXD-151, enabling a full range system to be powered from a single amplifier channel without
the need for external electronic crossovers.
The cabinet is constructed from 15mm (5/8”) birch plywood, screwed and glued together for
maximum rigidity. Pole mount sockets are fitted on the top and sides of the cabinet to enable full
range cabinets to be mounted on optional 35mm poles. When used in a horizontal format the two
side-mounted pole mounts allow two TXD series enclosures to be mounted on top of a single
TXD series manual
page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
bass cabinet to provide wider horizontal dispersion. Four recessed flush handles are provided for
easy lifting and carrying and the cabinet is pre-drilled for optional T4 wheels. A grey powder-
coated perforated steel mesh grille protects the drive units from damage.
M10 rigging points are provided on the top and rear of the cabinet, which allow single cabinets to
be suspended and angled in fixed installations using optional M10 shoulder eyebolts.
Two Neutrik Speakon NL4MP connectors are located on the rear panel, providing input and
parallel connections to additional TXD series cabinets.
TXD-118
The TXD-118 is a front-loaded low frequency loudspeaker enclosure designed to give bass and
sub-bass reinforcement to TXD series 2-way enclosures in a wide variety of live sound
applications, as well as in fixed installations ranging from cafes, pubs, bars and restaurants to
retail stores and houses of worship.
It consists of a front-loaded 18” low frequency driver in a birch plywood enclosure, optimally
tuned for extended low frequency response. The TXD-118 includes a low-pass crossover network
which filters high frequency signals from the bass driver when used in conjunction with 2-way
enclosures such as the TXD-121 or TXD-151, enabling a full range system to be powered from a
single amplifier channel without the need for external electronic crossovers
The enclosure is fitted with internal M10 threaded rigging points on the top and rear, which allow
single cabinets to be suspended and angled in fixed installations using optional M10 shoulder
eyebolts. A pole mount socket is fitted to the top of the cabinet to enable two-way enclosures to
be mounted on 35mm poles.
The cabinet is constructed from 15mm (5/8”) birch plywood, and is finished in a durable semi-matt
textured TurboBlue™ paint. Two flush handles are provided on the sides for easy lifting and
carrying, and four rubber feet are fitted to the bottom of the cabinet. Two Neutrik Speakon NL4MP
connectors provide input and parallel connections to additional TXD series loudspeakers.
TXD-218
The TXD-218 is a front-loaded low frequency loudspeaker enclosure designed to give bass and
sub-bass reinforcement to TXD series 2-way enclosures in a wide variety of live sound
applications, as well as in fixed installations ranging from cafes, pubs, bars and restaurants to
retail stores and houses of worship.
It consists of two front-loaded 18” low frequency drivers in a birch plywood enclosure, optimally
tuned for extended low frequency response. The TXD-218 includes a low-pass crossover network
which filters high frequency signals from the bass driver when used in conjunction with 2-way
enclosures such as the TXD-121 or TXD-151, enabling a full range system to be powered from a
single amplifier channel without the need for external electronic crossovers
TXD series manual
page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
The enclosure is fitted with internal M10 threaded rigging points on the top and rear, which allow
single cabinets to be suspended and angled in fixed installations using optional M10 shoulder
eyebolts.
The cabinet is constructed from 15mm (5/8”) birch plywood, and is finished in a durable semi-matt
textured TurboBlue™ paint. Two flush handles are provided on the sides for easy lifting and
carrying. Two Neutrik Speakon NL4MP connectors provide input and parallel connections to
additional TXD series loudspeakers.
TXD-12M
The TXD-12M is a compact passive two-way wedge monitor enclosure designed for use in a wide
variety of live sound, fixed installation and mobile DJ applications that require professional sound
quality in an easily transportable format.
It consists of a 12” reflex-loaded low frequency driver and a 1” high frequency driver on a 40ºH x
70ºV dispersion HF horn in an optimally tuned enclosure. These high grade components are
matched with a third order passive crossover network to ensure a seamless transition between the
HF and LF devices.
The crossover network incorporates a two-stage thermal overload protection system which
prevents damage to the high frequency driver, reacting instantly to large transient peaks while still
allowing wide dynamic range to be maintained. Although the protection system is transparent at
normal operating levels, as the level increases the signal is gradually and imperceptibly
compressed once the critical threshold has been reached.
The cabinet is constructed from 15mm (5/8”) birch plywood, screwed and glued together for
maximum rigidity. Its symmetrical shape allows the monitor to be inverted and used as left/right
mirror image pairs.
In addition to its primary function as a floor monitor, the TXD-12M is also suitable for front-of-
house applications and can be used with the integral pole mount socket on top of optional 35mm
poles and loudspeaker stands. Two recessed flush handles are provided for easy lifting and
carrying, and eight rubber feet are fitted. A grey powder-coated perforated steel mesh grille
protects the drive units from damage.
A Neutrik Speakon NL4MP connector is located at each end of the cabinet on recessed panels,
providing input and parallel link connections to additional TXD series monitors.
TXD-15M
The TXD-16M is a switchable passive/biamp two-way wedge monitor enclosure designed for use
in a wide variety of live sound, fixed installation and mobile DJ applications that require
professional sound quality in an easily transportable format.
It consists of a 15” reflex-loaded low frequency driver and a 1” high frequency driver on a 40ºH x
70ºV dispersion HF horn in an optimally tuned enclosure. These high grade components are
TXD series manual
page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
matched with a third order passive crossover network to ensure a seamless transition between the
HF and LF devices.
The crossover network incorporates a two-stage thermal overload protection system which
prevents damage to the high frequency driver, reacting instantly to large transient peaks while still
allowing wide dynamic range to be maintained. Although the protection system is transparent at
normal operating levels, as the level increases the signal is gradually and imperceptibly
compressed once the critical threshold has been reached.
The TXD-15M can also be operated in bi-amp mode with an external crossover and separate
amplifier channels simply by using the single Speakon NL4MD-V-S connector provided. Two
Neutrik Speakon NL4MP connectors are also provided for input and parallel link connections to
additional TXD series monitors.
The cabinet is constructed from 15mm (5/8”) birch plywood, screwed and glued together for
maximum rigidity. Its symmetrical shape allows the monitor to be inverted and used as left/right
mirror image pairs.
Two recessed flush handles are provided for easy lifting and carrying, and eight rubber feet are
fitted. A grey powder-coated perforated steel mesh grille protects the drive units from damage.
TXD series manual
page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
SYSTEM REQUIREMENTS
TXD series enclosures (with the exception of the TXD-252 and TXD-15M) are passive loudspeaker
systems. This means that they require only one amplifier channel for correct operation, the
frequency splitting between the low frequency driver and the high frequency driver or mid and
high frequency driver being accomplished by the internal passive crossover network built into
each enclosure.
If low frequency enclosures are used to extend low frequency response, this can be achieved
without the need for additional amplifier channels or external electronic crossovers. TXD series
low frequency enclosures are equipped with internal low pass crossover networks which filter mid
and high frequencies away from the bass speaker. Therefore a full range system consisting of, for
example, two TXD-121 and two TXD-115 can be powered from a single amplifier as shown below,
thereby saving the expense of additional amplifiers and external crossovers.
TXD-121
TXD-121
TXD SERIES
TXD SERIES
Output
Channel
B
Link
Input
Input
Link
Channel
A
Output
+
_
+
-
Pin
1
GND.
Pin
Pin
Pin
1
2
3
GND.
AMPLIFIER
Pin.2.
+
+
_
_
Pin
3
TXD-115
TXD-115
TXD SERIES
TXD SERIES
Connect the amplifier output to the Speakon INPUT socket on the bass enclosure.
Then connect an additional speaker cable from the LINK socket on the bass cabinet to the INPUT
socket on the full range cabinet. Speakon pin connections are shown below.
Speakon Pin W iring
1+
Passive
Pin 1+ Positive
Pin 1- Negative
Pin 2+ N/C
Bi-amp
LF positive
LF negative
HF positive
HF negative
2+
Pin 2- N/C
Back
Front
TXD series manual
page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
Bi-amplified operation
TXD series two-way loudspeakers can also be operated in bi-amplified mode together with any of
the available bass enclosures, in order to give enhanced audio performance and greater overall
sound pressure level. In this case one amplifier will power the full range loudspeakers, while
another is required to power the bass cabinets. An external 2-in, 4-out crossover, such as the LMS-
D4 digital loudspeaker management system, is required with a crossover frequency at 150Hz.
To operate TXD systems in bi-amplified mode, it is necessary to bypass the passive crossover in
the bass cabinet. To do this, undo the four screws holding the pole mount socket in place, and
firmly pull the pole mount out of the cabinet together with the passive crossover selection wiring.
In the case of the TXD-215, remove the lower side pole mount.
BI-AMP
(BY-PASS PASSIVE
CROSSOVER)
PASSIVE
Mode selection is determined by the position of the wire links on the connector block. To bypass
the internal passive crossover, connect the yellow link wire from the red to the black as shown in
the diagram above and replace the pole mount in the cabinet.
TXD-121
TXD-121
Output
Channel
B
Link
Input
Input
Link
Channel
A
Output
+
_
+
-
Pin
1
GND.
Pin
Pin
Pin
1
2
3
GND.
AMPLIFIER
Pin.2.
+
+
_
_
Pin
3
HIGH
<
BACK
NEXT
>
SCROLL
A
B
1
2
3
4
CLI
-24
MENU
ENTER
LIMIT
LMS D4
RS-232
MUTE
TXD-115
TXD-115
LOW
Output
Channel
B
Link
Input
Input
Link
Channel
A
Output
+
_
+
-
Pin
1
GND.
Pin
Pin
Pin
1
2
3
GND.
AMPLIFIER
Pin.2.
+
+
_
_
Pin
3
TXD series manual
page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
Amplifier considerations
Turbosound speaker enclosures should be driven by high quality power amplifiers designed for
true professional use. Such amplifiers will have balanced inputs, DC and RF fault protection, and
well-designed cooling systems for reliability.
The program power listed in the loudspeaker’s technical specification is the best guide to the size
of amplifier required for general-purpose applications. The amplifier should therefore be capable
of delivering long term broadband power equal to the loudspeaker’s program power rating at the
loudspeaker’s stated nominal impedance. This approach allows sufficient headroom to generate
good dynamic range.
RECOMMENDED AMPLIFIER POWER RATINGS:
The amplifier's rated r.m.s. continuous power output (20Hz – 20kHz, per channel) should be equal
to the program power handling of the loudspeaker at its nominal impedance.
In general, the more powerful the amplifier the better it will sound, provided that it is not driven
into sustained clipping. It should be understood that overdriving an insufficiently powered
amplifier is more likely to cause loudspeaker damage – the total energy in a heavily clipped signal
is far higher than in an unclipped signal – than operating a more powerful one within its ratings.
Equalisation
TXD series enclosures are designed to provide smooth and even frequency response. They do not
need excessive amounts of external equalisation to overcome the sonic deficiencies often found in
many lesser designs.
In order to compensate for the room acoustics, TXD series enclosures require only minimal
equalisation. As in any system, over-equalisation introduces phase shifts, distortion and a
reduction in headroom, usually causing more problems than it cures. Under most circumstances a
1/3 or 1/2 octave graphic equaliser will generally be adequate, with the fader settings applied
smoothly and as little as possible for the required room compensation. Most rooms will have
resonances that will be excited at particular frequencies needing some cut to help tame the sound.
These problems are most pronounced at the lower frequencies where loudspeakers generally
exhibit very little directional control. If you find that the system needs a lot of boost at lower
frequencies you may need additional sub-bass units. It is good practice to use as little equalisation
as possible, aiming to cut frequencies rather than adding large amounts of boost.
TXD series manual
page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
Dispersion
TXD series enclosures are designed to provide relatively wide (70°) horizontal coverage. This
allows the majority of live sound applications to be covered with single enclosures placed
individually to take advantage of this performance feature, for example either side of a stage in a
pub or small club environment as shown below. For best results the loudspeakers should be
either mounted on tripod stands or supported on straight poles on top of TXD series bass
enclosures. In order to optimise the sound coverage, point the loudspeakers inwards slightly, such
that the centre lines intersect at a distance approximately equal to twice the width of the stage.
STAGE
It is possible to array TXD series loudspeakers in order to achieve wider horizontal coverage and
in these applications it is recommended that the cabinets be placed such that the trapezoidal sides
are touching to ensure that the appropriate splay angle is observed. For guidance when designing
a sound system, a 70º horizontal polar pattern equals an angle of 35º either side of the centre line
at which the sound pressure level is 6dB down with respect to centre, (averaged over the whole
frequency range of the loudspeaker). Thus a 40º vertical dispersion gives an angle of 20º above
and below the horizon.
TXD series manual
page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
SYSTEM CONNECTIONS
The following diagrams illustrate several TXD series applications, ranging from a simple live
performance system of just two loudspeakers to a multi-zoned nightclub system.
Passive two way system
Connect a second pair of loudspeakers in parallel (shown with dotted lines) if required, using the
link connections on the rear panel.
Passive two-way system (TXD-252)
TXD series manual
page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
Passive full-range system with subs
Connect the power amplifier first to the bass cabinets, and then to the two-way loudspeakers
using the link connections.
Passive full-range system with subs
Connect to the bass cabinets as in the example above.
TXD series manual
page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
Passive full-range system with subs
Live performance monitor system
Take auxiliary feeds from the mixer via a graphic equaliser to two separate channels of a power
amplifier. Connect a second unit in parallel to form mirror-image pairs.
TXD series manual
page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
MOUNTING AND FIXING
A versatile range of mounting hardware is available that allows
enclosures to be used in a variety of ways, in either mobile
sound reinforcement applications or permanent installations.
A pole mount / tripod stand fitting is fitted to the bottom of the
TXD-081, TXD-121 and TXD-151 full range cabinets. Use this
pole mount facility with either optional Turbosound PA-60, PA-
90 or PA-100 35mm diameter poles, or conventional loudspeaker
tripod stands. Doing so will raise the loudspeaker above the
heads of an audience, providing better sound coverage from a
single enclosure. A matching pole mount socket is provided on
the top of the TXD series low frequency enclosures to accept the
various poles.
TXD series cabinets, including low frequency enclosures, can be rigged in permanent installations
using optional M10 shoulder eyebolts. The top of each cabinet is provided with two internal
threaded rigging points, and a further rigging point is provided on the back panel which is used to
vary the amount of downward angle. As supplied, these rigging points are fitted externally with
M10 countersunk slot-head screws. To facilitate rigging of the enclosure simply remove these M10
screws and replace them with M10 x 18mm shoulder eyebolts using a suitable thread locking
compound to avoid the possibility of loosening (please refer to Appendix C: Use of thread locking
compounds at the back of this manual). Note: Eyebolts must have a thread length of at least
18mm (3/4”).
NOTE: The rigging points are designed to suspend single enclosures only. There is no facility to
hang an additional cabinet below a flown TXD series enclosure.
TXD series manual
page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
IMPORTANT: Any installation, whether temporary or permanent, must be securely attached to the
structure of the building using chain, steel wires or web straps which are certified and load rated
for the purpose. The combined weight of the sound system, its cables and the rigging system
must be safely carried by the points at which attachment is made to the building or structure.
Great care must be taken in selecting the attachment points and methods, being absolutely sure of
the load carrying capacity of points chosen.
NOTE: The rigging of loudspeaker systems is an extremely serious matter with potentially lethal
consequences should anything go wrong. It is of vital importance that you, or other people rigging
the system, are suitably qualified to do so and have a full understanding of all the factors involved
with safety as a number one priority. Turbosound accepts no responsibility for any accident,
damage or failure of any rigged system. This rigging information is specifically related to the
requirements of TXD series enclosures only. For more detailed information on the whole topic of
rigging various handbooks are available. If you are in any doubt contact your Turbosound dealer
who will be able to refer you to an experienced rigging company.
CHOOSING THE BEST LOCATION
When using any loudspeaker system certain room parameters will affect the resultant sound
quality and coverage. For example, any boundary like a wall or floor will lift certain frequencies. If
you are placing the unit in a corner then a lift at the bass end is to be expected and it may sound
rather boomy. This can be compensated for moving the speaker or cutting low frequencies with a
graphic equaliser.
When speakers are flown in free space then boundary effects are minimised. The result is a
smooth frequency response without any boost at odd frequencies, but the bass end may appear
subjectively light. In this case increase the sub-bass level to bring the low end up.
The relationship between sound pressure level and distance is an “inverse square law” so
remember that every time the distance from the sound source is doubled the sound level
decreases by 6dB. For every 3dB increase of speaker output you need a doubling of input power
and you can work out the wattage input needed to give the required SPL levels at various
distances from the loudspeaker(s).
TXD series manual
page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
MAINTENANCE
If any of the drive units in your TXD series cabinet should cease functioning and need to be
replaced repaired, you are advised to remove the faulty unit from the cabinet and send it to a
professional service centre authorised to repair Turbosound loudspeakers.
Removal of the low frequency driver(s)
The perforated steel loudspeaker grille is held in place under tension only, fitting into slots at
either side of the baffle. There are no screws or other fixings holding the grille in place. Lay the
cabinet on its back and, using two small screwdrivers inserted through the mesh of the grille,
firmly pull the grille away from the slot at one side of the baffle until it is free. Set the grille aside
for later re-assembly.
Undo the four screws holding the driver(s) in place and carefully lift it out and away from the
cabinet. Make a note of the driver polarity for later reconnection. Disconnect the cables from the
drive unit and completely remove the driver from the cabinet.
To reinstate the driver(s) simply reverse the above procedure, making sure you observe the
correct polarity when reconnecting the cables back into the terminals of the drive units.
Removal of the high frequency compression driver
Remove the loudspeaker grille as described above and set the grille aside for later re-fitting.
Remove the horn/driver assembly by unscrewing the four screws holding the flange in place. Lift it
out and away from the cabinet. The high frequency driver can now be disassembled from the HF
horn.
TXD series manual
page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
TXD series manual
page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
APPENDIX A
Technical Specifications
TXD-081
TXD-121
TXD-12M
TXD-151
Dimensions
(H x W x D)
415mm x 307mm x
270mm
553mm x 411mm x
352mm
435mm x 533mm x
288mm
652mm x 465mm x
423mm
(16.3” x 12,1” x 10.6”)
(21.8” x 16.2” x 13.9”)
(17.1” x 21.8” x 11.3”)
(25.7” x 18.3” x 16.7”)
Net weight
11.3kg (24.9lbs)
20kg (44lbs)
18kg (39.6lbs)
28kg (61.6lbs)
Components
1 x 8” LF driver
1 x 1” HF compression
driver
1 x 12” LF driver
1 x 1” HF compression
driver
1 x 12” LF driver
1 x 1” HF compression
driver
1 x 15” LF driver
1 x 1” HF compression
driver
Frequency
response
70Hz – 20kHz ±4dB
60Hz – 20kHz ±4dB
65Hz – 20kHz ±4dB
45Hz – 20kHz ±4dB
Nominal
100°H x 60°V @-6dB pts
93dB, 1 watt @ 1metre
70°H x 40°V @-6dB pts
97dB, 1 watt @ 1metre
40°H x 70°V @-6dB pts
97dB, 1 watt @ 1metre
70°H x 40°V @-6dB pts
99dB, 1 watt @ 1 metre
dispersion
Sensitivity
Power
200 watts r.m.s.
300 watts r.m.s.
300 watts r.m.s.
300 watt r.m.s.
handling
400 watts program
600 watts program
600 watts program
600 watts program
Maximum
SPL
116dB continuous
122dB peak
122dB continuous
128dB peak
122dB continuous
128dB peak
124dB continuous
130dB peak
Construction
Grille
15mm (5/8”) birch
plywood
15mm (5/8”) birch
plywood
15mm (5/8”) birch
plywood
15mm (5/8”) birch
plywood
Powder coated
perforated steel
Powder coated
perforated steel
Powder coated
perforated steel
Powder coated
perforated steel
Connectors
(2) Speakon NL4MP
wired
(2) Speakon NL4MP
wired
(2) Speakon NL4MP
wired
(2) Speakon NL4MP
wired
pin 1+ positive,
pin 1- negative
pin 1+ positive,
pin 1- negative
pin 1+ positive,
pin 1- negative
pin 1+ positive,
pin 1- negative
Due to continuing product improvement the above specifications are subject to change.
TXD series manual
page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
TXD-252
TXD-115
TXD-215
TXD-118
Dimensions
(H x W x D)
1220mm x 540mm x
434mm
652mm x 465mm x
423mm
891mm x 550mm x
505mm
652mm x 540mm x
484mm
(48” x 21.3” x 17.1”)
(25.7” x 18.3” x 16.7”)
(35.1” x 21.7” x 19.9”)
(25.7” x 21.3” x 19.1”)
Net weight
47kg (103.4lbs)
25kg (55lbs)
47kg (103.4lbs)
28kg (61.6lbs)
Components
1 x 15” LF driver
1 x 3” coil
1 x 15” LF driver
2 x 15” LF drivers
1 x 18” LF driver
compression driver
Nominal dispersion 80°H x 50°V @-6dB pts
Frequency
response
40Hz – 20kHz ±4dB
43Hz – 150Hz ±4dB
40Hz – 150Hz ±4dB
36Hz – 150Hz ±4dB
Sensitivity
97dB, 1 watt @ 1metre 96dB, 1 watt @ 1metre 99dB, 1 watt @ 1metre 98dB, 1 watt @ 1
metre
Power handling
Maximum SPL
Construction
Grille
500 watts r.m.s.
300 watts r.m.s.
600 watts r.m.s.
300 watt r.m.s.
1000 watts program
600 watts program
1200 watts program
600 watts program
128dB continuous
134dB peak
121dB continuous
127dB peak
127dB continuous
133dB peak
123dB continuous
129dB peak
15mm (5/8”) birch
plywood
15mm (5/8”) birch
plywood
15mm (5/8”) birch
plywood
15mm (5/8”) birch
plywood
Powder coated
perforated steel
Powder coated
perforated steel
Powder coated
perforated steel
Powder coated
perforated steel
Connectors
(2) Speakon NL4MP
wired
(2) Speakon NL4MP
wired
(2) Speakon NL4MP
wired
(2) Speakon NL4MP
wired
pin 1+ positive,
pin 1- negative
pin 1+ positive,
pin 1- negative
pin 1+ positive,
pin 1- negative
pin 1+ positive,
pin 1- negative
Due to continuing product improvement the above specifications are subject to change.
TXD series manual
page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
APPENDIX B
Spares and Accessories
CD-111
CD-212
LS-8010
LS-1219
LS-1521
LS-1522
LS-1523
LS-1811
RC-1219
RC-1514
RC-1522
RC-1523
RC-1811
RD-111
RD-212
1” HF compression driver
3” diaphragm compression driver
8” LF loudspeaker
12” LF loudspeaker
15” LF loudspeaker
15” LF loudspeaker
15” LF loudspeaker
18" LF loudspeaker
Recone kit for LS-1219
Recone kit for LS-1514
Recone kit for LS-1522
Recone kit for LS-1523
Recone kit for LS-1811
Replacement diaphragm for CD-111
Replacement diaphragm for CD-212
MG-081
Metal grille for TXD-081
MG-121/X
MG-151/X
MG-115/X
MG-215/X
MG-252/X
MG-118/X
MG-218/X
PX-121/X
PX-151/X
PX-115/X
PX-215/X
PX-118/X
PX-252/X
Metal grille for TXD-121/TXD-12M
Metal grille for TXD-151
Metal grille for TXD-115
Metal grille for TXD-215
Metal grille for TXD-252
Metal grille for TXD-118
Metal grille for TXD-218
Passive crossover network for TXD-121/TXD-12M
Passive crossover network for TXD-151
Passive crossover network for TXD-115
Passive crossover network for TXD-215
Passive crossover network for TXD-118
Passive crossover network for TXD-252
Flying Accessories
EB-10
CB-55
WB-20
WB-55
PA-60
PA-90
PA-100
PA-120
PB-55
M10 x 18mm shoulder eyebolt
Ceiling bracket
Wall bracket
Wall bracket
35mm diameter straight pole, 60cm long
35mm diameter straight pole, 90cm long
35mm diameter straight pole, 100cm long
35mm diameter straight pole, 120 cm long
Pole bracket
TXD series manual
page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
APPENDIX C
Use of thread locking compounds
When assembling flying hardware to loudspeaker enclosures it is advisable to use thread-locking
compounds to eyebolts and other bolts in order to avoid any possibility of loosening.
The recommended thread-locking compound is Loctite 222.
The threaded rigging points used in TXD series enclosures are manufactured from zinc-plated
mild steel. Therefore, and additionally if the external bolts used are zinc-plated, zinc-passivated,
stainless steel or anodised (as the majority are), then the corresponding activator, Loctite 7471,
should be used to achieve 100% performance.
Application: Spray Loctite 7471 into the thread holes and allow it to evaporate. Apply Loctite 222
thread locking compound to the bolts prior to fitting, allowing sufficient to fill all the engaged
threads. Assemble components and tighten as necessary.
The parts may be disassembled by hand if required.
TXD series manual
page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
APPENDIX D
LIMITED WARRANTY
This Turbosound loudspeaker product is warranted to the original end-user purchaser and all
subsequent owners for a period of two (2) years from the original date of purchase.
Warranty Coverage
Warranty coverage includes defects in materials and workmanship. It does not include:
•
•
damage caused by accident, misuse, abuse, neglect or modification by any person other
than an authorised Turbosound representative,
damage caused by failure to operate the product in accordance with the instructions
contained in the user manual,
•
•
•
damage occurring during shipment in transit,
claims based on any misrepresentation by the seller,
products which do not have the original components as specified in the product
engineering information,
•
products on which the serial number has been removed or defaced.
Shipping
Should any fault develop with a component of your Turbosound system, please return the
product, freight pre-paid, in its original packing carton, along with proof of purchase such as the
original bill of sale or receipted invoice, and a description of the suspected fault to Turbosound
Ltd. (Att: Customer Service), Star Road, Partridge Green, West Sussex RH13 8RY, England, or your
local authorised Turbosound representative. The product serial number must be quoted in all
correspondence relating to the claim. Insurance is recommended, as Turbosound or its
representatives are not liable for loss or damage in transit. Turbosound will pay for return freight
costs should repairs be covered under warranty.
TXD series manual
page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
TXD series
Incidental and consequential damages
Turbosound's liability is limited to the repair or replacement, at our option, of any defective
product, and shall not be liable for any incidental and consequential damages including, without
limitation, injury to persons or property or loss of use.
Limitation of implied warranties
All implied warranties, including warranties of merchantability and fitness for a particular purpose,
are limited in duration to the length of this warranty.
This warranty is in addition to, and in no way detracts from, your statutory rights as a consumer.
No other warranty is expressed or implied.
Please record your purchase information below for future reference:
Dealer Name .................................................................................................................................................
Dealer Address .............................................................................................................................................
........................................................................................................................................................................
........................................................................................................................................................................
Post / Zip Code .............................................................................................................................................
Dealer telephone / fax .................................................................................................................................
Invoice number ............................................................................................................................................
Date of purchase ..........................................................................................................................................
Unit serial number .......................................................................................................................................
TXD series manual
page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Turbosound Ltd.
Star Road, Partridge Green
West Sussex RH13 8RY UK
Tel: +44 (0)1403 711447 Fax: +44 (0)1403 710155
TXD series manual
page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
|