TRUE FOOD SERVICE EQUIPMENT, INC.
2001 East Terra Lane • O’Fallon, Missouri 63366-4434
(636)-240-2400 • FAX (636)272-2408 • INT’L FAX (636)272-7546 • (800)325-6152
Parts Department (800)424-TRUE • Parts Department FAX# (636)272-9471
INSTALLATION MANUAL FOR T-23DT FREEZER /
REFRIGERATOR (SWING DOOR)
TABLE OF CONTENTS
Safety Information
Safety Precautions
Proper Disposal
Connecting Electricity
Adapter Plugs
1
2
3
3
Installation / Operation Instructions
Ownership
Required Tools
4
4
Uncrating
Leveling Cabinet
4
5
Installation of Castors or Optional Legs
Wire Gauge Chart
Sealing Cabinet to Floor & Electrical Inst.
Start-up
6
7
8
9
Shelving Install/Operation & Light Switches
Temperature Control Sequence of Operation
11
11-14
Maintenance, Care & Cleaning
Cleaning Condenser Coil
Stainless Steel Equipment Care & Cleaning
Light Bulb Replacement
15-16
17-18
18
Warranty (U.S.A. & CANADA ONLY!)
19
CONGRATULATIONS!
You have just purchased the finest commercial
freezer / refrigerator available. You can expect many
years of trouble-free operation.
T-23DT
T-23DT
FREEZER / REFRIGERATOR
SWING DOOR
#950157 • SB
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
SAFETY INFORMATION
How to Maintain Your
Freezer
/ Refrigerator to Receive the Most
Efficient and Successful Operation
You have selected one of the finest commercial refrigeration units made. It is manufactured
under strict quality controls with only the best quality materials available. Your TRUE cooler
when properly maintained will give you many years of trouble-free service.
WARNING!
Use this appliance for its intended purpose as described
in this Owner Manual.
This cabinet contains fluorinated greenhouse gas covered by the Kyoto Protocol
(please refer to cabinet’s inner label for type and volume,
GWP of 134a= 1,300. R404a= 3,800).
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
• This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
NOTE
We strongly recommend that any servicing be performed by
a qualified individual.
• Do not allow children to climb, stand or hang on the
shelves in the refrigerator. They could damage the
refrigerator and seriously injure themselves.
• Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet. Skin
may stick to these extremely cold surfaces.
• Unplug the refrigerator before cleaning and
making repairs.
• Setting temperature controls to the off position does
not remove power to the light circuit, perimeter
heaters, or evaporator fans.
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
• Keep fingers out of the “pinch point” areas;
clearances between the doors and between the doors
and cabinet are necessarily small; be careful closing
doors when children are in the area.
1
1
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
SAFETY INFORMATION
DANGER!
RISK OF CHILD ENTRAPMENT
PROPER DISPOSAL OF THE FREEZER /
REFRIGERATOR
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still
dangerous… even if they will sit for “just a few days.” If
you are getting rid of your old refrigerator, please follow
the instructions below to help prevent accidents.
Before You Throw Away Your Old Refrigerator or
Freezer:
• Take off the doors.
• Leave the shelves in place so that children may not
easily climb inside.
Refrigerant Disposal
Your old refrigerator may have a cooling system
that uses “Ozone Depleting ” chemicals. If you are
throwing away your old refrigerator, make sure the
refrigerant is removed for proper disposal by a
qualified service technician. If you intentionally
release any refrigerants you can be subject to
fines and imprisonment under provisions of the
environmental regulations.
USE OF EXTENSION CORDS
NEVER USE AN EXTENSION CORD! TRUE will not warranty any refrigerator that has been
connected to an extension cord.
2
2
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
SAFETY INFORMATION
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the ground prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with a
grounding plug which mates with a standard grounding wall
outlet to minimize the possibility of electric shock hazard from
this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Never unplug your refrigerator by pulling on the power cord.
Always grip plug firmly and pull straight out from the outlet.
Repair or replace immediately all power cords that have
become frayed or otherwise damaged. Do not use a cord that
shows cracks or abrasion damage along its length or at either
end.
If the outlet is a standard 2-prong outlet, it is your personal
responsibility and obligation to have it replaced with the
properly grounded wall outlet.
When removing the refrigerator away from the wall, be
careful not to roll over or damage the power cord.
The refrigerator should always be plugged into it’s own
individual electrical circuit, which has a voltage rating that
matches the rating plate.
This provides the best performance and also prevents
overloading building wiring circuits which could cause a fire
hazard from overheated wires.
USE OF ADAPTER PLUGS
NEVER USE AN ADAPTER PLUG! Because of potential safety hazards under certain conditions,
we strongly recommend against the use of an adapter plug.
(North America Use Only!)
NEMA plugs
TRUE uses these types of plugs. If you do not have
the right outlet have a certified electrician install
the correct power source.
3
3
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
INSTALLATION / OPERATION INSTRUCTIONS
OWNERSHIP
To ensure that your unit works properly from the first
day, it must be installed properly. We highly recommend
a trained refrigeration mechanic and electrician install
your TRUE equipment. The cost of a professional
installation is money well spent.
Before you start to install your TRUE unit, carefully
inspect it for freight damage. If damage is discovered,
immediately file a claim with the delivery freight carrier.
TRUE is not responsible for damage incurred during
shipment.
REQUIRED TOOLS
• Adjustable Wrench
• Phillips Head Screwdriver
• Level
UNCRATING
The following procedure is recommended for uncrating the
unit:
C. Remove door bracket on swinging glass door models (see
image 1-2). Do not throw the bracket or blocks away.
For future cabinet movement the bracket will need to be
installed so the glass door does not receive any damage.
(See image for bracket removal)
A. Remove the outer packaging, (cardboard and bubbles or
styrofoam corners and clear plastic). Inspect for concealed
damage. Again, immediately file a claim with the freight
carrier if there is damage.
NOTE
Keys for coolers with door locks are located in warranty packets.
B. Move your unit as close to the final location as possible
before removing the wooden skid.
1
2
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
LOCATING
A. Remove louver from the front of cabinet (see page 17 for
louver grill removal / reinstallation) and backguard (if
applicable) from rear of cabinet.
B. Skid bolts are located in each of 4 corners inside cabinet
bottom. (See photo A).
A
B
C
C. Remove skid bolts. (See photo B).
D. Cut straps if applicable. (See photo C).
E. Carefully lift cabinet off of skid.
Removing skid from bottom
of cabinet.
LEVELING
A. Set unit in its final location. Be sure there is adequate
ventilation in your room. Under extreme heat
conditions, (100°F+, 38°C+), you may want to install
an exhaust fan.
WARNING
Cabinet warranties are void if OEM power cord is tampered
with. TRUE will not warranty any units that are connected to
an extension cord.
WARNING
Warranty is void if ventilation is insufficient.
B. Proper leveling of your TRUE cooler is critical to
operating success (for non-mobile models). Effective
condensate removal and door operation will be
effected by leveling.
C. The cooler should be leveled front to back and side
to side with a level.
D. Ensure that the drain hose or hoses are positioned in
the pan.
E. Free plug and cord from inside the lower rear of the
cooler (do not plug in).
F. The unit should be placed close enough to the
electrical supply so that extension cords are never
used.
REMOTE UNITS (This section applies to remotes only!)
•
Remote cabinets must be ordered as remote.
We do not recommend converting from a
standard self contained to remote system.
All remote cabinets must be hard wired.
No castors available.
All remote cabinets come standard using 404A
refrigerant.
All remote units come standard with expansion
valve, liquid line solenoid, heated condensate
pan, and defrost timer when applicable.
•
Contact TRUE Technical Service for BTU
requirements.
•
•
No wiring necessary between cabinet and
condensing unit.
All remote condensing units purchased from
TRUE are 208/230 volts single phase.
•
•
•
If you have any questions regarding this section, please
call TRUE at 1-(800)-325-6152.
•
5
5
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
INSTALLATION OF CASTORS OR OPTIONAL LEGS
Important Safeguard for installation of leg/castor (Images 1-5 demonstrate procedure)
Securing Castors and Legs
B. Install the desired number of shims, making sure the
slot of the shim is in contact with the threaded stem
of the castor. (See image 2)
To obtain maximum strength and stability of the unit,
it is important that you make sure each castor is secure.
Optional legs are hand-tightened securely against the
lower rail assembly see image 4-5. The bearing race on
the castor or the top edge of the leg must make firm
contact with the rail.
C. If more than one shim is used, turn the slot at a 90°
angle so they are not in line.
D. Turn the bearing race clockwise to tighten and secure
the castor by tightening the anchoring bolt with a
3/4 inch open-end wrench or the tool provided.
(See image 3)
Unit leveling
Four leveling shims have been provided for leveling
castored units positioned on uneven floors. Shims must
be positioned between rail end and bearing race.
CAUTION
To avoid damage to lower rail assembly, slowly raise unit to
upright position.
NOTE
Open holes located on the cross members of the frame rail
should be plugged before unit is in use.
A. Turn the bearing race counter-clockwise until the
cabinet is level. Level front to back and side to side.
(diagonally)
4
1
2
3
Thread castor into the underside of
cabinet frame rail.
Thread leg into cabinet bottom
frame rail.
For leveling, insert the shim
Use the tool provided to tighten
the castor into place.
between the castor and frame rail.
Lower Rail
Assembly
Lower Rail Assembly
Rail End
Rail End
Snug Fit
Here
Bearing
Race
Snug Fit
Here
Leveling Shim
5
The end of the leg is adjustable
to easy leveling.
Leg
Castor
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
CONDUCTORS AND CIRCUITS
Wire Gauge for 2% Voltage Drop in Supply Circuits
115 Volt
Distance In Feet To Center of Load
30 40 50 60 70
14 14 14
Amps
20
14
14
14
14
14
80
14
14
14
14
12
90
14
14
14
12
12
100
14
14
14
12
12
120
14
14
12
12
10
140
14
14
12
10
10
160
14
12
12
10
10
2
3
4
5
6
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
7
8
14
14
14
14
14
14
14
14
14
14
14
14
14
14
12
14
14
12
12
12
14
12
12
12
10
12
12
12
10
10
12
12
10
10
10
12
10
10
10
8
10
10
10
10
8
10
10
8
10
8
8
8
8
8
6
9
8
10
12
8
8
8
8
14
16
18
20
25
14
14
14
14
12
14
12
12
12
10
12
12
10
10
10
10
10
10
10
8
10
10
8
10
8
8
8
8
8
6
8
8
8
6
6
8
8
8
6
6
6
6
8
6
5
6
6
8
5
4
6
6
5
5
4
8
8
8
6
8
30
35
40
45
50
12
10
10
10
10
10
10
8
8
8
8
6
6
8
6
6
6
6
6
6
6
6
5
6
6
5
5
4
6
5
5
4
4
6
5
4
4
3
5
4
4
3
3
4
4
3
3
2
4
3
2
2
1
3
2
2
1
1
8
8
Wire Gauge for 2% Voltage Drop in Supply Circuits
230 Volts
Distance In Feet To Center of Load
Amps
20
14
14
14
14
14
30
14
14
14
14
14
40
14
14
14
14
14
50
14
14
14
14
14
60
14
14
14
14
14
70
14
14
14
14
14
80
14
14
14
14
14
90
14
14
14
14
14
100
14
14
14
14
12
120
14
14
14
12
12
140
14
14
12
12
12
160
14
12
12
12
10
5
6
7
8
9
10
12
14
16
18
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
12
14
14
14
12
12
14
14
12
12
12
14
12
12
12
10
12
12
12
10
10
12
12
10
10
10
12
10
10
10
8
10
10
10
8
10
10
8
8
8
8
20
25
30
35
40
14
14
14
14
14
14
14
12
12
12
14
12
12
10
10
12
12
10
10
10
10
10
10
10
8
10
10
10
8
10
10
8
10
10
8
10
8
8
8
6
6
6
8
6
6
6
5
8
6
6
5
5
8
8
8
8
6
8
8
6
50
60
12
12
10
10
10
10
10
10
10
8
10
8
8
6
6
6
6
6
6
6
6
6
5
5
6
6
6
5
5
4
6
6
5
5
4
4
6
6
5
4
4
3
6
5
4
4
3
3
5
4
4
3
3
2
4
4
2
2
1
1
4
3
2
2
1
1
70
8
80
90
100
8
8
6
8
6
7
7
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
ELECTRICAL INSTRUCTIONS
A. Before your new unit is connected to a power supply,
check the incoming voltage with a voltmeter. If
anything less than 100% of the rated voltage for
operation is noted, correct immediately.
B. All units are equipped with a service cord, and must
be powered at proper operating voltage at all times.
Refer to cabinet data plate for this voltage.
WARNING
Compressor warranties are void if compressor burns out
due to low voltage.
WARNING
Power supply cord ground should not be removed!
NOTE
To reference wiring diagram - Remove front louvered grill,
wiring diagram is positioned on the inside cabinet wall.
TRUE requires that a sole use circuit be dedicated for the
unit. Failure to do so voids warranty.
SEALING CABINET TO FLOOR
Step 1 - Position Cabinet
Step 6
Allow one inch between the wall and rear of the
refrigerator to assure proper ventilation. For freezers
3 inches between the wall and rear of the cabinet will
assure proper ventilation.
Raise and block the rear of the cabinet
Step 7
Apply sealant on floor as outline in Step 5. on other
three sides.
Step 2 - Level Cabinet
Step 8
Cabinet should be level, side to side and front to back.
Place a carpenter’s level in the interior floor in four
places:
A. Position level in the inside floor of the unit near the
doors. (Level should be parallel to cabinet front).
Level cabinet.
Examine to see that cabinet is sealed to floor around
entire perimeter.
NOTE
Asphalt floors are very susceptible to chemical attack. A
layer of tape on the floor prior to applyingthe sealant will
protect the floor.
B. Position level at the inside rear of cabinet. (Again
level should be placed parallel to cabinet back).
NSF Approved Sealants:
C. Perform similar procedures to steps a & b by placing
the level on inside floor (left and right sides - parallel
to the depth of the cooler). Level cabinet.
1. Minnesota Mining #ECU800 Caulk
2. Minnesota Mining #ECU2185 Caulk
3. Minnesota Mining #ECU1055 Bead
4. Minnesota Mining #ECU1202 Bead
5. Armstrong Cork - Rubber Caulk
6. Products Research Co. #5000 Rubber Caulk
7. G.E. Silicone Sealer
Step 3
Draw an outline on the base on the floor.
Step 4
Raise and block the front side of the cabinet.
Step 5
Apply a bead of “NSF Approved Sealant”, (see list
below), To floor on half inch inside the outline drawn.
The bead must be heavy enough to seal the entire cabinet
surface when it is down on the sealant.
8. Dow Corning Silicone Sealer
8
8
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
STARTUP
A. The compressor is ready to operate. Plug in the
cooler.
NOTE
B. Factory approximate refrigerator temperature of 35°F
and approximate freezer temperature of -10˚F. Allow
unit to function several hours, completely cooling
cabinet before changing the control setting.
C. Excessive tampering with the control could lead to
service difficulties. Should it ever become necessary
to replace temperature control, be sure it is ordered
from your TRUE dealer or recommended service
agent.
D. Good air flow in your TRUE unit is critical. Be
careful to load product so that it neither presses
against the back wall, nor comes within four inches
of the evaporator housing. Refrigerated air off the
coil must circulate down the back wall.
If the cooler is disconnected or shut off, wait five minutes
before starting again.
RECOMMENDATION
Before loading product we recommend you run your TRUE
unit empty for two to three days. This allows you to be sure
electrical wiring and installation are correct and no shipping
damage has occurred. Remember, our factory warranty
does not cover product loss!
REPLACEMENT PARTS
TRUE maintains a record of the cabinet serial number
for your cooler. If at any time during the life of your
cooler, a part is needed, you may obtain this part by
furnishing the model number and serial number to the
company from whom you purchased the cooler. Call
Toll-Free: (800)-424-TRUE (Direct to Parts Department).
(800)-325-6152 (U.S.A. & Canada only) or call:
(636)-240-2400.
9
9
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
SHELVING INSTALLATION / OPERATION &
LIGHT SWITCH LOCATION
WARNING
Do not use pliers or any crimping tools when
installing shelf clips. Altering shelf clips in any
way can lead to shelving instability.
3
1
You may need to squeeze or twist the bottom
of the shelf clip to install)
(Installing top tab of shelf clip)
Step 2
Bottom tab of the shelf clip will fit tightly.
You may need to squeeze or twist the
bottom of the shelf clip to install. (See
image 2 & 3).
4
(Shelf clip installation complete)
Step 3
After installation, the shelf clip will fit snug
into the shelf standard. e shelf clip should
not be loose or able to wiggle out of the
shelf standard.
For Proper Shelf Clip Installation Please
Read The Following Instructions.
Step 1
2
Shelf Installation Tips
Shelf clips are to be installed into the shelf
standards next to the labels on the interior
cabinet wall. is label can be seen in
images 1-4. Install the top tab of the shelf
clip into the proper hole. Push up on the
bottom of the clip. (See image 1).
(Installing bottom of the shelf clip)
1. Install all the shelf clips before installing
the shelves.
2. Start at the bottom in terms of shelf
installation and work your way up.
3. Always lay the back of each shelf down
on the rear clips before the front.
T-Series
& GDM-5
Airflow
SHELF & ORGANIZER INSTALLATION:
Guard
Step 1
A. Hook shelf clips onto shelf standards. (see illustration).
B. Position all four shelf clips equal in distance from the
floor for flat shelves.
Shelf
Shelf
WIRE SHELVES
Wire shelves are oriented so that cross support bars are facing down.
NOTE
Shelf
Clip
Pillaster
T-Series models include an airflow guard on the rear of shelves to
maintain an air space at the rear of the cabinet. (see illustration).
LIGHT SWITCH LOCATION:
Step 2
Light switch location depends upon the T-Series model. Most
T-Series models will have the light switch located inside the unit on
the right side of the ceiling. Some models have the switch located
on the right side of the evaporator housing along the interior ceiling.
Place shelves on shelf clips making sure all corners are seated
properly.
10
10
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
DANFOSS TEMPERATURE CONTROL (FREEZER
SEQUENCE OF OPERATION)
1. Cabinet is plugged in.
a. Display will illuminate showing “deF”.
b. Cabinet will start in a Defrost Cycle.
2. During the initial Defrost Cycle, the evaporator fan(s) and the compressor will remain off for a minimum of 4
minutes.
a. After the Defrost Cycle there will be a 2 minute delay.
b. After the 2 minute delay the compressor will start.
c. The evaporator fans will remain off for an additional 3 minutes.
d. The display will continue to show “deF” for an additional 30 minutes.
3. The electronic control will cycle the compressor and the evaporator fan(s) on and off determined by the
Set-Point and Differential temperatures (Set-Point is adjustable).
a. The Set-Point is the preprogrammed temperature which shuts off the compressor and evaporator fan(s).
b. The Differential is the preprogrammed temperature that is added to the Set-Point temperature that will start
the compressor and evaporator fan(s).
c. The Danfoss control is designed to read and display a cabinet temperature. This cabinet temperature may
reflect the refrigeration cycle of the Set-Point and it’s Differential.
Example: If the Set-Point is -6°F/1°C and the Differential is 6°F/4°C
(Set-Point) -6°F + 6 (Differential) = 0°F
Or
(Set-Point) -21.4°C + 3.3 (Differential) = -18.1°C
The compressor will cycle off -6°F/-21.4°C and back on at 0°F/-18.1°C
4. The electronic control is preprogrammed to initiate defrost every 4 hours of compressor run time
(non-adjustable).
a. At this time the evaporator fans and the compressor will turn off.
b. Once a preprogrammed temperature of the evaporator coil is reached, the Defrost Cycle will terminate and the
2 minute delay will occur.
c. After the 2 minute delay the compressor will restart.
d. The evaporator fans will remain off for an additional 3 minutes.
e. The display will continue to show “deF” for an additional 30 minutes.
TRUE Manufacturing recommends that only the Set-Point may be adjusted due to certain conditions.
11
11
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
DANFOSS TEMPERATURE CONTROL
(REFRIGERATOR SEQUENCE OF OPERATION)
1. Cabinet is plugged in.
a. Display will illuminate showing “deF”.
b. Cabinet will start in a Defrost Cycle.
2. During the initial Defrost Cycle, the evaporator fan(s) will run but the compressor will remain off for a minimum
of 4 minutes.
a. After the Defrost Cycle there will be a 2 minute delay and the evaporator fan(s) will stop.
b. After the 2 minute delay the compressor will start, and evaporator fan(s) will delay 60 seconds.
c. The display will continue to show “deF” for an additional 30 minutes.
3. The electronic control will cycle the compressor and the evaporator fan(s) on and off determined by the
Set-Point and Differential temperatures (Set-Point is adjustable).
a. The Set-Point is the preprogrammed temperature which shuts off the compressor and evaporator fan(s).
b. The Differential is the preprogrammed temperature that is added to the Set-Point temperature that will start
the compressor and evaporator fan(s).
c. The Danfoss control is designed to read and display a cabinet temperature. This cabinet temperature may
reflect the refrigeration cycle of the Set-Point and it’s Differential.
Example: If the Set-Point is 34°F/1.1°C and the Differential is 6°F/3.3°C
(Set-Point) 34°F + 6 (Differential) = 40°F
Or
(Set-Point) 1.1°C + 3.3 (Differential) = 4.4°C
The compressor will cycle off 34°F/1.1°C and back on at 40°F/4.4°C
4. The electronic control is preprogrammed to initiate defrost every 4 hours of compressor run time
(non-adjustable).
a. At this time the evaporator fans will continue to run but the compressor will turn off.
b. Once a preprogrammed temperature of the evaporator coil is reached, the Defrost Cycle will terminate and the
2 minute delay will start stopping the evaporator fan(s).
c. After the 2 minute delay the compressor will restart, and evaporator fan(s) will delay 60 seconds.
d. The display will continue to show “deF” for an additional 30 minutes.
TRUE Manufacturing recommends that only the Set-Point may be adjusted due to certain conditions.
12
12
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
Danfoss Electronic Control (Power On)
Press both buttons to
power on temp control
TURNING ON POWER
A. Press both buttons to power on the temperature control.
Danfoss Electronic Control (Power Off)
Press both buttons
and hold for 6 seconds
to power off temp
control
TURNING OFF POWER
A. Press both buttons and hold for 6 seconds to power off
the temperature control.
13
13
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
Danfoss Electronic Control (Defrost)
Press bottom button
and hold for 6 seconds
to start defrost
DEFROST
A. Press bottom button and hold for 6 seconds to defrost.
Danfoss Electronic Control
(Cut out Temperature)
or
Press and release top
or bottom button for 2
seconds to display cut
out temperature
CUT OUT TEMPERATURE
CHANGE CUT OUT TEMPERATURE
A. Press and release top or bottom button for 2 seconds A. Raise or lower the set point use the top or bottom
to display cut out temperature.
button to go up or down. Release the button and
temperature will go back.
NOTE - Cut in temperature is the set point plus the fix
differential.
14
14
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
MAINTENANCE, CARE & CLEANING
CLEANING THE CONDENSER COIL
When using electrical appliances, basic safety precautions should be followed, including the following:
Step 8
REQUIRED TOOLS:
Reinstall louver assembly onto unit with appropriate fastener
and clips. Tighten all screws.
Step 9
Connect unit to power and check to see if compressor is
running.
•
•
•
•
Phillips Screwdriver
Stiff Bristle Brush
Adjustable Wrench
Air Tank or CO2 Tank • Vacuum Cleaner
Step 1
Disconnect power to unit.
Step 2
SLIDE DOOR MODELS: (See Image 1)
Take off lower grill assembly by removing two (2) screws in
lower corners. (older models may have snap lock tabs instead
of screws).
Loosen screws holding the top pivot pins. Swing grill up and
remove frame hooks from pivot pins at top of louver.
SWING DOOR MODELS: (See Image 2)
Take off lower grill assembly by opening the door and
removing screws from the top of the louver grill. Some models
have a door light switch. Please use caution when removing
the grill on these models. Do not pinch wires. For reinstall,
reattach the grill to the magnets on front of the cabinet and
reinstall the screws on top of the grill.
1
Slide Door Models
Step 3
Remove bolts anchoring compressor assembly to frame rails
and carefully slide out. (tube connections are flexible)
Step 4
Clean off accumulated dirt from the condenser coil and the
fan with a stiff bristle brush.
2
Swing Door Models
Step 5
Lift cardboard cover above fan at plastic plugs and carefully
clean condenser coil and fan blades.
Step 6
INDOOR LOCATION:
After brushing condenser coil vacuum dirt from coil, and
interior floor.
Image 3.
OUTDOOR LOCATION:
(GDM-33, GDM-47, and GDM-49 only) After brushing
condenser coil blow CO2 through condenser from fin side to
fan. (See Image 4.)
Step 7
1
2
7
Replace cardboard cover. Carefully slide compressor assembly
back into position and replace bolts.
Image 4.
15
15
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
IMPORTANT WARRANTY INFORMATION
Condensers accumulate dirt and require cleaning every 30 days. Dirty condensers result in compressor failure, product loss,
and lost sales... which are not covered by warranty.
If you keep the Condenser clean you will minimize your service expense and lower your electrical costs. The Condenser
requires scheduled cleaning every thirty days or as needed.
Air is pulled through the Condenser continuously, along with dust, lint, grease, etc.
A dirty Condenser can result in NON-WARRANTEED part & Compressor Failures, Product Loss, and Lost Sales.
Proper cleaning involves removing dust from the Condenser. By using a soft brush, or vacuuming the Condenser with a shop
vac, or using CO2, nitrogen, or pressurized air.
If you cannot remove the dirt adequately, please call your refrigeration service company.
On most of the units the condenser is accessible in the rear of the unit. You must remove the cabinet grill to expose the
Condenser.
The Condenser looks like a group of vertical fins. You need to be able to see through the condenser for the unit to function at
maximum capacity. Do not place filter material in front of condensing coil. This material blocks air-flow to the coil similar to
having a dirty coil.
THE CLEANING OF THE CONDENSER IS NOT
COVERED BY THE WARRANTY!
HOW TO CLEAN THE CONDENSER:
1. Disconnect the electrical power to the unit.
2. Remove the louvered grill.
3. Vacuum or brush the dirt, lint, or debris from the finned condenser coil.
4. If you have a significant dirt build up you can blow out the condenser with compressed air.
(CAUTION MUST BE USED to avoid eye injury. Eye protection is recommended.)
5. When finished be sure to replace the louvered grill. The grill protects the condenser.
6. Reconnect the electrical power to the unit.
If you have any questions, please call TRUE Manufacturing at 636-240-2400 or 800-325-6152 and ask for the Service
Department. Service Department Availability Monday-Friday 7:30 a.m. to 5:30p.m. and Saturday 8:00 a.m. to 12:00 a.m. CST.
16
16
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
Stainless Steel Equipment Care and Cleaning
CAUTION: Do not use any steel wool, abrasive or chlorine based products to clean stainless steel surfaces.
• Stainless Steel Opponents
There are three basic things which can break down your stainless steel’s passivity layer and allow corrosion to rear
its ugly head.
1) Scratches from wire brushes, scrapers, and steel pads are just a few examples of items that can be abrasive to
stainless steel’s surface.
2) Deposits left on your stainless steel can leave spots. You may have hard or soft water depending on what part of
the country you live in. Hard water can leave spots. Hard water that is heated can leave deposits if left to sit too
long. These deposits can cause the passive layer to break down and rust your stainless steel. All deposits left from
food prep or service should be removed as soon as possible.
3) Chlorides are present in table salt, food, and water. Household and industrial cleaners are the worst type of
chlorides to use.
• 8 steps that can help prevent rust on stainless steel:
1. Using the correct cleaning tools
Use non-abrasive tools when cleaning your stainless steel products. The stainless steel’s passive layer will not be
harmed by soft cloths and plastic scouring pads. Step 2 tells you how to find the polishing marks.
2. Cleaning along the polish lines
Polishing lines or “grain” are visible on some stainless steels. Always scrub parallel to visible lines on some stainless
steels. Use a plastic scouring pad or soft cloth when you cannot see the grain.
3. Use alkaline, alkaline chlorinated or non-chloride containing cleaners
While many traditional cleaners are loaded with chlorides, the industry is providing an ever increasing choice of
non-chloride cleaners. If you are not sure of your cleaner’s chloride content contact your cleaner supplier. If they
tell you that your present cleaner contains chlorides, ask if they have an alternative. Avoid cleaners containing
quaternary salts as they can attack stainless steel, causing pitting and rusting.
4. Water Treatment
To reduce deposits, soften the hard water when possible. Installation of certain filters can remove corrosive and
distasteful elements. Salts in a properly maintained water softener can be to your advantage. Contact a treatment
specialist if you are not sure of the proper water treatment.
5. Maintaining the cleanliness of your food equipment
Use cleaners at recommended strength (alkaline, alkaline chlorinated or non-chloride). Avoid build-up of hard
stains by cleaning frequently. When boiling water with your stainless steel equipment, the single most likely cause
of damage is chlorides in the water. Heating any cleaners containing chlorides will have the same damaging effects.
6. Rinse
When using chlorinated cleaners you must rinse and wipe dry immediately. It is better to wipe standing cleaning
agents and water as soon as possible. Allow the stainless steel equipment to air dry. Oxygen helps maintain the
passivity film on stainless steel.
7. Hydrochloric acid (muriatic acid) should never be used on stainless steel
8. Regularly restore/passivate stainless steel
17
17
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
Stainless Steel Equipment Care and Cleaning
Recommended cleaners for certain situations / environments of stainless steel
A) Soap, ammonia and detergent medallion applied with a cloth or sponge can be used for routine
cleaning.
B) Arcal 20, Lac-O-Nu Ecoshine applied provides barrier film for fingerprints and smears.
C) Cameo, Talc, Zud First Impression is applied by rubbing in the direction of the polished lines for
stubborn stains and discoloring.
D) Easy-off and De-Grease It oven aid are excellent for removals on all finishes for grease-fatty acids,
blood and burnt-on foods.
E) Any good commercial detergent can be applied with a sponge or cloth to remove grease and oil.
F) Benefit, Super Sheen, Sheila Shine are good for restoration / passivation.
NOTE
The use of stainless steel cleaners or other such solvents is not
recommended on plastic parts. Warm soap and water will suffice.
LIGHT BULB REPLACEMENT
IDL (Integrated Door Lighting)
WARNING
INTERIOR LIGHTS:
Disconnect power to cabinet before replacing light bulbs.
• Simply unscrew the light bulb(See Image 1 & 2).
IDL (INTEGRATED DOOR LIGHTING):
• Squeeze the plastic lampshield together and pull away
from the door (See Image 3).
• Push the bulb down while pulling the spring
activated lampholder up. This will give you enough
clearance to take the bulb out (See Image 4).
1
Interior Light
3
4
2
IDL (Integrated Door Lighting)
IDL (Integrated Door Lighting)
Interior Light
18
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TRUE REFRIGERATION®
MADE IN
WARRANTY INFORMATION (U.S.A & CANADA ONLY!)
U.S.A.
SINCE 1945
ONE YEAR PARTS & LABOR WARRANTY
TRUE warrants to the original purchaser of every new TRUE refrigerated unit, the cabinet and all parts thereof, to be free from defects in material or workmanship,
under normal and proper use and maintenance service as specified by TRUE and upon proper installation and start-up in accordance with the instruction packet supplied
with each TRUE unit. TRUE’s obligation under this warranty is limited to a period of one (1) year from the date of original installation or 15 months after shipment date
from TRUE, whichever occurs first.
Any part covered under this warranty that are determined by TRUE to have been defective within one (1) year of original installation or fifteen (15) months after
shipment date from manufacturer, whichever occurs first, is limited to the repair or replacement, including labor charges, of defective parts or assemblies. The labor
warranty shall include standard straight time labor charges only and reasonable travel time, as determined by TRUE.
ADDITIONAL FOUR YEAR COMPRESSOR WARRANTY
In addition to the one (1) year warranty stated above, TRUE warrants its hermetically and semi-hermetically sealed compressor to be free from defects in both
material and workmanship under normal and proper use and maintenance service for a period of four (4) additional years from the date of original installation but not to
exceed five (5) years and three (3) months after shipment from the manufacturer.
Compressors determined by TRUE to have been defective within this extended time period will, at TRUE’s option, be either repaired or replaced with a compressor
or compressor parts of similar design and capacity.
The four (4) year extended compressor warranty applies only to hermetically and semi-hermetically sealed parts of the compressor and does not apply to any other
parts or components, including, but not limited to, cabinet, paint finish, temperature control, refrigerant, metering device, driers, motor starting equipment, fan assembly
or any other electrical component, etcetera.
404A/134A COMPRESSOR WARRANTY
The four year compressor warranty detailed above will be voided if the following procedure is not carefully adhered to:
1. This system contains R404A or R134A refrigerant and polyol ester lubricant. The polyol ester lubricant has rapid moisture absorbing qualities. If long exposure to
the ambient conditions occur, the lubricant must be removed and replaced with new. For oil amounts and specifications please call TRUE technical service department
(800-325-6152). Failure to comply with recommended lubricant specification will void the compressor warranty.
2. Drier replacement is very important and must be changed when a system is opened for servicing. A drier using XH-7 desiccant or an exact replacement solid core
drier must be used. The new drier must also be the same capacity as the drier being replaced.
3. Micron level vacuums must be achieved to insure low moisture levels in the system. 500 microns or lower must be obtained.
WARRANTY CLAIMS
All claims for labor or parts must be made directly through TRUE. All claims should include: model number of the unit, the serial number of the cabinet, proof of
purchase, date of installation, and all pertinent information supporting the existence of the alleged defect.
In case of warranty compressor, the compressor model tag must be returned to TRUE along with above listed information.
Any action or breach of these warranty provisions must be commenced within one (1) year after that cause of action has occurred.
WHAT IS NOT COVERED BY THIS WARRANTY
TRUE’s sole obligation under this warranty is limited to either repair or replacement of parts, subject to the additional limitations below. This warranty neither
assumes nor authorizes any person to assume obligations other than those expressly covered by this warranty.
NO CONSEQUENTIAL DAMAGES. TRUE IS NOT RESPONSIBLE FOR ECONOMIC LOSS; PROFIT LOSS; OR SPECIAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES, INCLUDING WITHOUT LIMITATION, LOSSES OR DAMAGES ARISING FROM FOOD OR PRODUCT SPOILAGE CLAIMS WHETHER OR NOT ON ACCOUNT
OF REFRIGERATION FAILURE.
WARRANTY IS NOT TRANSFERABLE. This warranty is not assignable and applies only in favor of the original purchaser/user to whom delivered. ANY SUCH
ASSIGNMENT OR TRANSFER SHALL VOID THE WARRANTIES HEREIN MADE AND SHALL VOID ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IMPROPER USAGE. TRUE ASSUMES NO LIABILITY FOR PARTS OR LABOR COVERAGE FOR COMPONENT FAILURE OR OTHER DAMAGES RESULTING FROM
IMPROPER USAGE OR INSTALLATION OR FAILURE TO CLEAN AND/OR MAINTAIN PRODUCT AS SET FORTH IN THE WARRANTY PACKET PROVIDED WITH THE
UNIT.
RESIDENTIAL APPLICATIONS: TRUE assumes no liability for parts or labor coverage for component failure or other damages resulting from installation in
non-commercial or residential applications.
ALTERATION, NEGLECT, ABUSE, MISUSE, ACCIDENT, DAMAGE DURING TRANSIT OR INSTALLATION, FIRE, FLOOD, ACTS OF GOD. TRUE is not responsible
for the repair or replacement of any parts that TRUE determines have been subjected after the date of manufacture to alteration, neglect, abuse, misuse, accident,
damage during transit or installation, fire, flood, or act of God.
IMPROPER ELECTRICAL CONNECTIONS. TRUE IS NOT RESPONSIBLE FOR THE REPAIR OR REPLACEMENT OF FAILED OR DAMAGED COMPONENTS
RESULTING FROM ELECTRICAL POWER FAILURE, THE USE OF EXTENSION CORDS, LOW VOLTAGE, OR VOLTAGE DROPS TO THE UNIT.
NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE: THERE ARE NO OTHER WARRANTIES, EXPRESSED, IMPLIED
OR STATUTORY, EXCEPT THE ONE (1) YEAR PARTS & LABOR WARRANTY AND THE ADDITIONAL FOUR (4) YEAR COMPRESSOR WARRANTY AS DESCRIBED
ABOVE. THESE WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, INCLUDING IMPLIED WARRANTY AND MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
OUTSIDE U.S./Canada: This warranty does not apply to, and TRUE is not responsible for, any warranty claims made on products sold or used outside the United
States or Canada.
19
19
Download from Www.Somanuals.com. All Manuals Search And Download.
|