TRUE FOOD SERVICE EQUIPMENT, INC.
2001 East Terra Lane • O’Fallon, Missouri 63366-4434
(636)-240-2400 • FAX (636)272-2408 • INT’L FAX (636)272-7546 • (800)325-6152
Parts Department (800)424-TRUE • Parts Department FAX# (636)272-9471
INSTALLATION MANUAL FOR TRUE FOOD PREP MODELS
TABLE OF CONTENTS
Safety Information
Safety Precautions
Proper Disposal
1
2
3
3
Connecting Electricity
Adapter Plugs
Installation / Operation Instructions
Ownership
Required Tools
4
4
4
5
6
7
7
7
8
9
9
9
Uncrating
Locating & Lid Installation
Leveling & Castor Adjusting
Storage Bins
Drawer Alignment
Electrical Instructions
Wire Gauge Chart
Sequence of Operation
Startup
Temperature Control Location
Maintenance, Care & Cleaning
Cleaning Condenser Coil
Stainless Steel Equipment Care & Cleaning
Composite Cutting Board Maintenance
Warranty (U.S.A. & Canada Only!)
TFP-32-12M-D-2
10-11
12-13
13
14
CONGRATULATIONS!
You have just purchased the finest commercial
refrigerator available. You can expect many years of
trouble-free operation.
TRUE FOOD PREP MODELS
#954377
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
SAFETY INFORMATION
How to Maintain Your
Unit to
Receive the Most Efficient and
Successful Operation
You have selected one of the finest commercial refrigeration units made. It is manufactured
under strict quality controls with only the best quality materials available. Your TRUE cooler
when properly maintained will give you many years of trouble-free service.
WARNING!
Use this appliance for its intended purpose as described in
this Owner Manual.
This cabinet contains fluorinated greenhouse gas covered by the Kyoto Protocol
(please refer to cabinet’s inner label for type and volume,
GWP of 134a= 1,300. R404a= 3,800).
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
•
•
•
•
•
This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
Do not allow children to climb, stand or hang on the
shelves in the refrigerator. They could damage the
refrigerator and seriously injure themselves.
Do not touch the cold surfaces in the refrigerator
compartment when hands are damp or wet. Skin
may stick to these extremely cold surfaces.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
NOTE
We strongly recommend that any servicing be preformed by
a qualified individual.
•
Unplug the refrigerator before cleaning and
making repairs.
•
Setting temperature controls to the 0 position does
not remove power.
Keep fingers out of the “pinch point” areas;
clearances between the doors and between the doors
and cabinet are necessarily small; be careful closing
doors when children are in the area.
1
1
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
SAFETY INFORMATION
DANGER!
RISK OF CHILD ENTRAPMENT
PROPER DISPOSAL OF THE REFRIGERATOR
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still
dangerous… even if they will sit for “just a few days.” If
you are getting rid of your old refrigerator, please follow
the instructions below to help prevent accidents.
Before You Throw Away Your Old Refrigerator or
Freezer:
Refrigerant Disposal
Your old refrigerator may have a cooling system
that uses “Ozone Depleting ” chemicals. If you are
throwing away your old refrigerator, make sure the
refrigerant is removed for proper disposal by a
qualified service technician. If you intentionally
release any refrigerants you can be subject to
fines and imprisonment under provisions of the
environmental regulations.
•
•
Take off the doors.
Leave the shelves in place so that children may not
easily climb inside.
USE OF EXTENSION CORDS
NEVER USE AN EXTENSION CORD! TRUE will not warranty any refrigerator that has been connected to an extension cord.
2
2
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
SAFETY INFORMATION
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the ground prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord from this appliance is equipped with
a grounding plug which minimizes the possibility of
electric shock hazard.
This provides the best performance and also prevents
overloading building wiring circuits which could cause a
fire hazard from overheated wires.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Never unplug your refrigerator by pulling on the power
cord. Always grip plug firmly and pull straight out from
the outlet.
If the outlet is a standard 2-prong outlet, it is your
personal responsibility and obligation to have it replaced
with the properly grounded wall outlet.
Repair or replace immediately all power cords that have
become frayed or otherwise damaged. Do not use a cord
that shows cracks or abrasion damage along its length or
at either end.
The refrigerator should always be plugged into it’s own
individual electrical circuit, which has a voltage rating
that matches the rating plate.
When removing the refrigerator away from the wall, be
careful not to roll over or damage the power cord.
USE OF ADAPTER PLUGS
NEVER USE AN ADAPTER PLUG! Because of potential safety hazards under certain conditions, we strongly recommend
against the use of an adapter plug.
(North America Use Only!)
NEMA plugs
TRUE uses these types of plugs. If
you do not have the right outlet have
a certified electrician install the correct
power source.
3
3
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
INSTALLATION / OPERATION INSTRUCTIONS
OWNERSHIP
To ensure that your unit works properly from the first
day, it must be installed properly. We highly recommend
a trained refrigeration mechanic and electrician install
your TRUE equipment. The cost of a professional
installation is money well spent.
Before you start to install your TRUE unit, carefully
inspect it for freight damage. If damage is discovered,
immediately file a claim with the delivery freight carrier.
TRUE is not responsible for damage incurred during
shipment.
REQUIRED TOOLS
•
•
•
3/8” Socket Wrench
Phillips Head Screwdriver
Level
UNCRATING
The following procedure is recommended for uncrating the unit:
A. Remove the outer packaging, (cardboard and bubbles or styrofoam corners and clear plastic). Inspect for concealed
damage. Again, immediately file a claim with the freight carrier if there is damage.
B. Move your unit as close to the final location as possible before removing the wooden skid.
NOTE
Keys for coolers with door locks are located in warranty packets.
REMOTE UNITS
REMOTE UNITS (This section applies to remotes only!)
•
•
•
Contact TRUE Technical Service for BTU
requirements.
No wiring necessary between cabinet and
condensing unit.
All remote condensing units purchased from
TRUE are 208/230 volts single phase.
•
Remote cabinets must be ordered as remote.
We do not recommend converting for a standard
self contained to remote system.
•
•
•
All remote cabinets must be hard wired.
No castors available.
All remote cabinets come standard using 404A
refrigerant.
If you have any questions regarding this section, please
call TRUE at 1-(800)-325-6152.
•
All remote units come standard with expansion
valve, liquid line solenoid, heated condensate pan,
and defrost timer when applicable.
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
LOCATING
A. Place packing material behind cabinet as a cushion.
B. Remove skid by unscrewing all base rail anchor
WARNING:
brackets. Place skid to the side.
Make sure all bins, bin support bars, and lid are
removed from unit before placing unit on its back.
C. Carefully lift cabinet upright.
Removing
skid from
bottom of
cabinet.
Carefully lay the unit on its back to remove skid.
When lifting unit remember to
leave the cabinet upright for 24 hours before
plugging into power source.
CUTTING BOARD
A. Remove thumbscrews from cutting board brackets.
(See figure 1).
B. Remove brackets from both sides of the board.
C. Carefully lift cutting board.
Figure 1.
ANCHORING THE TFP HOOD COVER
TFP Hood Installation Instruction
A. This is TRUE’s recommended procedure for
HOOD
installing the lid to the hood.
See the illustration.
Assembly
HINGE PIN
1. Locate the lid, (packaged within the cardboard
container on top of the unit), and position under the
hood.
2. Place lid into final position, (beneath hood), align
hood hinge pin with anchor hole on lid.
3. Repeat procedure for other end of hood.
LID
5
5
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
LEVELING AND CASTOR ADJUSTING
Adjusting Castors for Proper Leveling
A. Set unit in its final location. Be sure there is adequate
ventilation in your room. Under extreme heat
conditions, (100°F+, 38°C+), you may want to install
an exhaust fan.
Level unit. If unit is not level shims are required.
Follow these instructions to install shims.
1. Remove front and rear grill depending upon which
castor needs adjusting. Locate the castor box. (See
image 1).
WARNING
Warranty is void if ventilation is insufficient.
2. Lay unit on it’s back. Use soft packing material and
be careful not to scratch the unit. Remove pans and
lid and place them to the side before laying unit on
it’s back.
B. Proper leveling of your TRUE unit is critical to
operating success (for non-mobile models). Effective
condensate removal and drawer/door operation will
be effected by leveling.
3. Loosen castor with tool provided. (See image 3).
C. The unit should be leveled from top of the cabinet.
Place a level on the top of the unit front to back and
side to side.
4. Install the desired number of shims, making sure the
slot of the shim is in contact with the threaded stem
of the castor. (See image 4). If more than one shim
is used, turn the slot at a 90° angle so they are not in
line.
5. Each unit has one castor box different from the
others. This box is totally inclosed. Remove this
castor box from bottom of unit. Back out four
screws anchoring the box. You will need a 1/4” hex
head nut driver to disassemble this castor box. (See
image 4).
D. Ensure that the drain hose or hoses are positioned in
the pan.
E. Free plug and cord from inside the lower rear of the
cooler (do not plug in).
F. The unit should be placed close enough to the
electrical supply so that extension cords are never
used.
WARNING
Cabinet warranties are void if OEM power cord is tampered
with. TRUE will not warranty any units that are connected to
an extension cord.
6. After adjusting castor reassemble and reinstall castor
box. Then carefully upright unit and reinstall pans
and lid.
Castor Box
Anchor
Screws
1
4
2
3
Locate castor box
Loosen castor.
Install shims.
One castor box on each unit is
fully inclosed.
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
STORAGE BINS
A. Bins can be arranged in different layouts for preferred
placement.
B. Remove bins and adjust cross bars for desired
placement. (See images 1-2).
Image 1
Image 2
DRAWER ALIGNMENT
A. For drawer face alignment four screws are located on
the back of the drawer face. (See image 3).
B. Loosen these four screws and adjust the drawer face
aligning with the rest of the drawers. Anchor the
four screws once alignment is achieved.
Image 3
ELECTRICAL INSTRUCTIONS
A. Before your new unit is connected to a power supply,
check the incoming voltage with a voltmeter. If
anything less than 100% of the rated voltage for
operation is noted, correct immediately.
B. All units are equipped with a service cord, and must
be powered at proper operating voltage at all times.
Refer to cabinet data plate for this voltage.
TRUE requires that a sole use circuit be dedicated for the
unit. Failure to do so voids warranty.
WARNING
Compressor warranties are void if compressor burns out
due to low voltage.
WARNING
Power supply cord ground should not be removed!
NOTE
To reference wiring diagram - Remove front louvered grill,
wiring diagram is positioned on the inside cabinet wall.
7
7
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
CONDUCTORS AND CIRCUITS
Wire Gauge for 2% Voltage Drop in Supply Circuits
115 Volt
Distance In Feet To Center of Load
30 40 50 60 70
14 14 14
Amps
20
14
14
14
14
14
80
14
14
14
14
12
90
14
14
14
12
12
100
14
14
14
12
12
120
14
14
12
12
10
140
14
14
12
10
10
160
14
12
12
10
10
2
3
4
5
6
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
7
8
14
14
14
14
14
14
14
14
14
14
14
14
14
14
12
14
14
12
12
12
14
12
12
12
10
12
12
12
10
10
12
12
10
10
10
12
10
10
10
8
10
10
10
10
8
10
10
8
10
8
8
8
8
8
6
9
8
10
12
8
8
8
8
14
16
18
20
25
14
14
14
14
12
14
12
12
12
10
12
12
10
10
10
10
10
10
10
8
10
10
8
10
8
8
8
8
8
6
8
8
8
6
6
8
8
8
6
6
6
6
8
6
5
6
6
8
5
4
6
6
5
5
4
8
8
8
6
8
30
35
40
45
50
12
10
10
10
10
10
10
8
8
8
8
6
6
8
6
6
6
6
6
6
6
6
5
6
6
5
5
4
6
5
5
4
4
6
5
4
4
3
5
4
4
3
3
4
4
3
3
2
4
3
2
2
1
3
2
2
1
1
8
8
Wire Gauge for 2% Voltage Drop in Supply Circuits
230 Volts
Distance In Feet To Center of Load
Amps
20
14
14
14
14
14
30
14
14
14
14
14
40
14
14
14
14
14
50
14
14
14
14
14
60
14
14
14
14
14
70
14
14
14
14
14
80
14
14
14
14
14
90
14
14
14
14
14
100
14
14
14
14
12
120
14
14
14
12
12
140
14
14
12
12
12
160
14
12
12
12
10
5
6
7
8
9
10
12
14
16
18
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
12
14
14
14
12
12
14
14
12
12
12
14
12
12
12
10
12
12
12
10
10
12
12
10
10
10
12
10
10
10
8
10
10
10
8
10
10
8
8
8
8
20
25
30
35
40
14
14
14
14
14
14
14
12
12
12
14
12
12
10
10
12
12
10
10
10
10
10
10
10
8
10
10
10
8
10
10
8
10
10
8
10
8
8
8
6
6
6
8
6
6
6
5
8
6
6
5
5
8
8
8
8
6
8
8
6
50
60
12
12
10
10
10
10
10
10
10
8
10
8
8
6
6
6
6
6
6
6
6
6
5
5
6
6
6
5
5
4
6
6
5
5
4
4
6
6
5
4
4
3
6
5
4
4
3
3
5
4
4
3
3
2
4
4
2
2
1
1
4
3
2
2
1
1
70
8
80
90
100
8
8
6
8
6
8
8
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
SEQUENCE OF OPERATION
Temperature Control Sequence of Operation
When the cabinet is plugged the unit will start up in a defrost cycle. The evaporator fan is hard-wired and will
continue to run during this time. The cooler will stay in defrost for a minimum of 4 minutes or until the coil
temperature reaches at least 41˚F. The maximum time the cooler will be in defrost is 40 minutes. At the end of
the defrost cycle, there will be a 2 minute delay to allow any water to drip off of the evaporator coil. After this
time, the compressors will come on and the cooler should start to cool down. The compressors will run until the
temperature control is satisfied. Every 4 hours of compressor run time, the cooler will go into defrost and remain
in defrost until the coil temperature reaches 41˚F.
NOTE:
When the unit is first plugged in it will take at least 6 minutes
before the compressor starts.
STARTUP
A. The compressor is ready to operate. Plug in the
cooler.
NOTE
If the cooler is disconnected or shut off, wait five minutes before
starting again.
B. Temperature control set at No. 4 position gives
refrigerators an approximate temperature of 35°F.
Allow unit to function several hours, completely
cooling cabinet before changing the control setting.
C. Excessive tampering with the control could lead to
service difficulties. Should it ever become necessary
to replace temperature control, be sure it is ordered
from your TRUE dealer or recommended service
agent.
RECOMMENDATION
Before loading product we recommend you run your TRUE unit
empty for two to three days. This allows you to be sure electrical
wiring and installation are correct and no shipping damage
has occurred. Remember, our factory warranty does not cover
product loss!
REPLACEMENT PARTS
D. Good air flow in your TRUE unit is critical. Be
careful to load product so that it neither presses
against the back wall, nor comes within four inches
of the evaporator housing. Refrigerated air off the
coil must circulate down the back wall.
TRUE maintains a record of the cabinet serial number for your
cooler. If at any time during the life of your cooler, a part is
needed, you may obtain this part by furnishing the model number
and serial number to the company from whom you purchased
the cooler. Call Toll-Free: (800)-424-TRUE (Direct to Parts
Department). (800)-325-6152 (U.S.A. & Canada only) or call:
(636)-240-2400.
TEMPERATURE CONTROL LOCATION
The temperature control is located are the back of the
unit. (See image 1).
Image 1
9
9
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
MAINTENANCE, CARE & CLEANING
CLEANING THE CONDENSER COIL
When using electrical appliances, basic safety precautions should be followed, including the following:
REQUIRED TOOLS:
•
•
•
•
Phillips Screwdriver
Stiff Bristle Brush
Adjustable Wrench
Vacuum Cleaner
Step 1
Disconnect power to unit.
Step 2
Image 1.
Remove the rear grill by backing out screws.
(See image 3).
Step 3
Remove bolts anchoring compressor assembly
to frame rails and carefully slide out. (tube
connections are flexible)
Step 4
Clean off accumulated dirt from the condenser coil and
the fan with a stiff bristle brush. (See image 1).
Image 2.
Step 5
Lift cardboard cover above fan at plastic plugs and
carefully clean condenser coil and fan blades.
Step 6
After brushing condenser coil vacuum dirt from coil, and
interior floor. (See image 2)
Step 7
Replace cardboard cover. Carefully slide compressor
assembly back into position and replace bolts.
Image 3.
Step 8
Reinstall rear grill assembly onto unit. Tighten all screws.
Step 9
Connect unit to power and check to see if compressor is
running.
Image 4.
10
10
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
IMPORTANT WARRANTY INFORMATION
Condensers accumulate dirt and require cleaning every 30 days. Dirty condensers result in
compressor failure, product loss, and lost sales... which are not covered by warranty.
If you keep the Condenser clean you will minimize your service expense and lower your electrical costs. The Condenser
requires scheduled cleaning every thirty days or as needed.
Air is pulled through the Condenser continuously, along with dust, lint, grease, etc.
A dirty Condenser can result in NON-WARRANTEED part & Compressor Failures, Product Loss, and Lost Sales.
Proper cleaning involves removing dust from the Condenser. By using a soft brush, or vacuuming the Condenser with a shop
vac, or using CO2, nitrogen, or pressurized air.
If you cannot remove the dirt adequately, please call your refrigeration service company.
The Condenser looks like a group of vertical fins. You need to be able to see through the condenser for the unit to function at
maximum capacity. Do not place filter material in front of condensing coil. This material blocks air-flow to the coil similar to
having a dirty coil.
THE CLEANING OF THE CONDENSER IS NOT
COVERED BY THE WARRANTY!
HOW TO CLEAN THE CONDENSER:
1. Disconnect the electrical power to the unit.
2. Remove the louvered grill.
3. Vacuum or brush the dirt, lint, or debris from the finned condenser coil.
4. If you have a significant dirt build up you can blow out the condenser with compressed air. (CAUTION MUST
BE USED to avoid eye injury. Eye protection is recommended.)
5. When finished be sure to replace the louvered grill. The grill protects the condenser.
6. Reconnect the electrical power to the unit.
If you have any questions, please call TRUE Manufacturing at 636-240-2400 or 800-325-6152 and ask for the
Service Department. Service Department Availability Monday-Friday 7:30 a.m. to 5:30p.m. and Saturday 8:00 a.m.
to 12:00 a.m. CST.
11
11
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
Stainless Steel Equipment Care and Cleaning
CAUTION: Do not use any steel wool, abrasive or chlorine based products to clean stainless steel surfaces.
•
Stainless Steel Opponents
There are three basic things which can break down your stainless steel’s passivity layer and allow
corrosion to rear its ugly head.
1) Scratches from wire brushes, scrapers, and steel pads are just a few examples of items that can be
abrasive to stainless steel’s surface.
2) Deposits left on your stainless steel can leave spots. You may have hard or soft water depending on
what part of the country you live in. Hard water can leave spots. Hard water that is heated can
leave deposits if left to sit too long. These deposits can cause the passive layer to break down and
rust your stainless steel. All deposits left from food prep or service should be removed as soon as
possible.
3) Chlorides are present in table salt, food, and water. Household and industrial cleaners are the worst
type of chlorides to use.
8 steps that can help prevent rust on stainless steel:
1. Using the correct cleaning tools
Use non-abrasive tools when cleaning your stainless steel products. The stainless steel’s passive
layer will not be harmed by soft cloths and plastic scouring pads. Step 2 tells you how to find the
polishing marks.
2. Cleaning along the polish lines
Polishing lines or “grain” are visible on some stainless steels. Always scrub parallel to visible lines
on some stainless steels. Use a plastic scouring pad or soft cloth when you cannot see the grain.
3. Use alkaline, alkaline chlorinated or non-chloride containing cleaners
While many traditional cleaners are loaded with chlorides, the industry is providing an ever
increasing choice of non-chloride cleaners. If you are not sure of your cleaner’s chloride content
contact your cleaner supplier. If they tell you that your present cleaner contains chlorides, ask if
they have an alternative. Avoid cleaners containing quaternary salts as they can attack
stainless steel, causing pitting and rusting.
4. Water Treatment
To reduce deposits, soften the hard water when possible. Installation of certain filters can remove
corrosive and distasteful elements. Salts in a properly maintained water softener can be to your
advantage. Contact a treatment specialist if you are not sure of the proper water treatment.
5. Maintaining the cleanliness of your food equipment
Use cleaners at recommended strength (alkaline, alkaline chlorinated or non-chloride). Avoid
build-up of hard stains by cleaning frequently. When boiling water with your stainless steel
equipment, the single most likely cause of damage is chlorides in the water. Heating any cleaners
containing chlorides will have the same damaging effects.
6. Rinse
When using chlorinated cleaners you must rinse and wipe dry immediately. It is better to wipe
standing cleaning agents and water as soon as possible. Allow the stainless steel equipment to air
dry. Oxygen helps maintain the passivity film on stainless steel.
7. Hydrochloric acid (muriatic acid) should never be used on stainless steel
8. Regularly restore/passivate stainless steel
12
12
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
Stainless Steel Equipment Care and Cleaning
Recommended cleaners for certain situations / environments of
stainless steel
A) Soap, ammonia and detergent medallion applied with a cloth or sponge can be used for routine
cleaning.
B) Arcal 20, Lac-O-Nu Ecoshine applied provides barrier film for fingerprints and smears.
C) Cameo, Talc, Zud First Impression is applied by rubbing in the direction of the polished lines for
stubborn stains and discoloring.
D) Easy-off and De-Grease It oven aid are excellent for removals on all finishes for grease-fatty acids,
blood and burnt-on foods.
E) Any good commercial detergent can be applied with a sponge or cloth to remove grease and oil.
F) Benefit, Super Sheen, Sheila Shine are good for restoration / passivation.
NOTE
The use of stainless steel cleaners or other such solvents is not
recommended on plastic parts. Warm soap and water will suffice.
Composite Cutting Board Maintenance
Please see comments from Supplier regarding composite cutting boards below.
RE: Composite Cutting Boards Manufactured From Richlite Materail and Warping.
“To prevent warping on cutting boards manufactured from Richlite® material, simply turn the board
over on a regular scheduled basis. Warping is caused by continued moisture and temperature
differences on the top and bottom of the boards. By turning the board over, this will allow both
sides of the board to receive the same exposure.
There is a chance that larger size boards may warp as a characteristic of the material.”
13
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TRUE REFRIGERATION®
MADE IN
U.S.A.
WARRANTY INFORMATION (U.S.A & CANADA ONLY!)
SINCE 1945
ONE YEAR PARTS & LABOR WARRANTY
TRUE warrants to the original purchaser of every new TRUE refrigerated unit, the cabinet and all parts thereof, to be free from defects in material or workmanship,
under normal and proper use and maintenance service as specified by TRUE and upon proper installation and start-up in accordance with the instruction packet supplied
with each TRUE unit. TRUE’s obligation under this warranty is limited to a period of one (1) year from the date of original installation or 15 months after shipment date
from TRUE, whichever occurs first.
Any part covered under this warranty that are determined by TRUE to have been defective within one (1) year of original installation or fifteen (15) months after
shipment date from manufacturer, whichever occurs first, is limited to the repair or replacement, including labor charges, of defective parts or assemblies. The labor
warranty shall include standard straight time labor charges only and reasonable travel time, as determined by TRUE.
ADDITIONAL FOUR YEAR COMPRESSOR WARRANTY
In addition to the one (1) year warranty stated above, TRUE warrants its hermetically and semi-hermetically sealed compressor to be free from defects in both
material and workmanship under normal and proper use and maintenance service for a period of four (4) additional years from the date of original installation but not to
exceed five (5) years and three (3) months after shipment from the manufacturer.
Compressors determined by TRUE to have been defective within this extended time period will, at TRUE’s option, be either repaired or replaced with a compressor
or compressor parts of similar design and capacity.
The four (4) year extended compressor warranty applies only to hermetically and semi-hermetically sealed parts of the compressor and does not apply to any other
parts or components, including, but not limited to, cabinet, paint finish, temperature control, refrigerant, metering device, driers, motor starting equipment, fan assembly
or any other electrical component, etcetera.
404A/134A COMPRESSOR WARRANTY
The four year compressor warranty detailed above will be voided if the following procedure is not carefully adhered to:
1. This system contains R404A or R134A refrigerant and polyol ester lubricant. The polyol ester lubricant has rapid moisture absorbing qualities. If long exposure to
the ambient conditions occur, the lubricant must be removed and replaced with new. For oil amounts and specifications please call TRUE technical service department
(800-325-6152). Failure to comply with recommended lubricant specification will void the compressor warranty.
2. Drier replacement is very important and must be changed when a system is opened for servicing. A drier using XH-7 desiccant or an exact replacement solid core
drier must be used. The new drier must also be the same capacity as the drier being replaced.
3. Micron level vacuums must be achieved to insure low moisture levels in the system. 500 microns or lower must be obtained.
WARRANTY CLAIMS
All claims for labor or parts must be made directly through TRUE. All claims should include: model number of the unit, the serial number of the cabinet, proof of
purchase, date of installation, and all pertinent information supporting the existence of the alleged defect.
In case of warranty compressor, the compressor model tag must be returned to TRUE along with above listed information.
Any action or breach of these warranty provisions must be commenced within one (1) year after that cause of action has occurred.
WHAT IS NOT COVERED BY THIS WARRANTY
TRUE’s sole obligation under this warranty is limited to either repair or replacement of parts, subject to the additional limitations below. This warranty neither
assumes nor authorizes any person to assume obligations other than those expressly covered by this warranty.
NO CONSEQUENTIAL DAMAGES. TRUE IS NOT RESPONSIBLE FOR ECONOMIC LOSS; PROFIT LOSS; OR SPECIAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES, INCLUDING WITHOUT LIMITATION, LOSSES OR DAMAGES ARISING FROM FOOD OR PRODUCT SPOILAGE CLAIMS WHETHER OR NOT ON ACCOUNT
OF REFRIGERATION FAILURE.
WARRANTY IS NOT TRANSFERABLE. This warranty is not assignable and applies only in favor of the original purchaser/user to whom delivered. ANY SUCH
ASSIGNMENT OR TRANSFER SHALL VOID THE WARRANTIES HEREIN MADE AND SHALL VOID ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IMPROPER USAGE. TRUE ASSUMES NO LIABILITY FOR PARTS OR LABOR COVERAGE FOR COMPONENT FAILURE OR OTHER DAMAGES RESULTING FROM
IMPROPER USAGE OR INSTALLATION OR FAILURE TO CLEAN AND/OR MAINTAIN PRODUCT AS SET FORTH IN THE WARRANTY PACKET PROVIDED WITH THE
UNIT.
RESIDENTIAL APPLICATIONS: TRUE assumes no liability for parts or labor coverage for component failure or other damages resulting from installation in non-
commercial or residential applications.
ALTERATION, NEGLECT, ABUSE, MISUSE, ACCIDENT, DAMAGE DURING TRANSIT OR INSTALLATION, FIRE, FLOOD, ACTS OF GOD. TRUE is not responsible
for the repair or replacement of any parts that TRUE determines have been subjected after the date of manufacture to alteration, neglect, abuse, misuse, accident,
damage during transit or installation, fire, flood, or act of God.
IMPROPER ELECTRICAL CONNECTIONS. TRUE IS NOT RESPONSIBLE FOR THE REPAIR OR REPLACEMENT OF FAILED OR DAMAGED COMPONENTS
RESULTING FROM ELECTRICAL POWER FAILURE, THE USE OF EXTENSION CORDS, LOW VOLTAGE, OR VOLTAGE DROPS TO THE UNIT.
NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE: THERE ARE NO OTHER WARRANTIES, EXPRESSED, IMPLIED
OR STATUTORY, EXCEPT THE ONE (1) YEAR PARTS & LABOR WARRANTY AND THE ADDITIONAL FOUR (4) YEAR COMPRESSOR WARRANTY AS DESCRIBED
ABOVE. THESE WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, INCLUDING IMPLIED WARRANTY AND MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
OUTSIDE U.S./Canada: This warranty does not apply to, and TRUE is not responsible for, any warranty claims made on products sold or used outside the United
States or Canada.
14
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|