Safety • Set-Up • Operation • Adjustments • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR’S MANUAL
Two-Stage Snow Thrower
IMPORTANT:
READ SAFETY RULES AND
INSTRUCTIONS CAREFULLY
BEFORE OPERATING EQUIPMENT.
769-03253
07/23/07
PRINTED IN U.S.A.
P. O. Box 1386, KITCHENER, ONTARIO N2G 4J1
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Safety
Labels
WARNING
This symbol points
out important safety
instructions which,
if not followed, could
endanger the per-
sonal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
#3ꢀꢀꢀꢁꢂ
A chute clean-out tool is fastened to the top
of the auger housing with a mounting clip. The
tool is designed to clear a chute assembly of
ice and snow.
result in personal
injury. When you see
this symbol, HEED
Chute Clean-out
Tool
ITS WARNING!
This item is fastened with a cable tie at the
factory. Cut the cable tie before operating the
snow thrower.
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
WARNING: Never use your
hands to clear a clogged chute
assembly. Shut off engine and
remain behind handles until
all moving parts have stopped
before using the clean-out tool
to clear the chute assembly.
and follow the warnings
and instructions
in this manual
and on the machine.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo-
nents contain or emit chemicals known to State of California to cause cancer and
birth defects or other reproductive harm.
ꢀ
DANGER: This machine was built to be operated according to the safe operation practices in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.
Safe
Operation
Practices
Safe Handling of Gasoline
Training
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes, which can ignite.
Wash your skin and change clothes immediately.
2. Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them quickly.
3. Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the instructions and safe operation practices
in this manual and on the machine and be trained and
supervised by an adult.
4. Never allow adults to operate this machine without proper
instruction.
5. Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.
7. Exercise caution to avoid slipping or falling, especially
when operating in reverse.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine is hot
or running.
WARNING
e. Allow engine to cool at least two minutes before refuel-
ing.
This symbol points
out important safety
instructions which,
if not followed, could
endanger the per-
sonal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
f. Never over fill fuel tank. Fill tank to no more than ½ inch
below bottom of filler neck to provide space for fuel
expansion.
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and equip-
ment. Move machine to another area. Wait 5 minutes
before starting the engine.
i. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light (e.g. furnace,
water heater, space heater, clothes dryer etc.).
j. Allow machine to cool at least 5 minutes before storing.
Preparation
1. Thoroughly inspect the area where the equipment is to be
used. Remove all doormats, newspapers, sleds, boards,
wires and other foreign objects, which could be tripped
over or thrown by the auger/impeller.
2. Always wear safety glasses or eye shields during
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
3. Do not operate without wearing adequate winter outer gar-
ments. Do not wear jewelry, long scarves or other loose
clothing, which could become entangled in moving parts.
Wear footwear which will improve footing on slippery
surfaces.
result in personal
injury. When you see
this symbol, HEED
4. Use a grounded three-wire extension cord and receptacle
for all units with electric start engines.
ITS WARNING!
5. Adjust collector housing height to clear gravel or crushed
rock surfaces.
Your Responsibility
Restrict the use
6. Disengage all control levers before starting the engine.
7. Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual.
of this power machine
to persons who read,
understand
8. Let engine and machine adjust to outdoor temperature
before starting to clear snow.
and follow the warnings
and instructions
in this manual
and on the machine.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Maintenance & Storage
1. Do not put hands or feet near rotating parts, in the
auger/impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
1. Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and adjust-
ment sections of this manual.
ꢀ
2. The auger/impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
2. Before cleaning, repairing, or inspecting machine disengage
all control levers and stop the engine. Wait until the
auger/impeller come to a complete stop. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
3. The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
Safe
Operation
Practices
3. Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
4. Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
5. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless and
deadly gas.
5. Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”
6. Check controls periodically to verify they engage and
disengage properly and adjust, if necessary. Refer to the
adjustment section in this operator’s manual for instructions.
7. Maintain or replace safety and instruction labels, as neces-
sary.
6. Do not operate machine while under the influence of alcohol
or drugs.
7. Muffler and engine become hot and can cause a burn. Do
not touch.
8. Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while operat-
ing on slopes.
WARNING
10. Plan your snow-throwing pattern to avoid discharge towards
windows, walls, cars etc. Thus, avoiding possible property
damage or personal injury caused by a ricochet.
11. Never direct discharge at children, bystanders and pets or
allow anyone in front of the machine.
This symbol points
out important safety
instructions, which
if not followed, could
endanger the per-
sonal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
8. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
13. Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
11. Always refer to the operator’s manual for proper instructions
on off-season storage.
14. Disengage power to the auger/impeller when transporting or
not in use.
15. Never operate machine at high transport speeds on slippery
surfaces. Look down and behind and use care when
backing up.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way.Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
16. If the machine should start to vibrate abnormally, stop the
engine, disconnect the spark plug wire and ground it against
the engine. Inspect thoroughly for damage. Repair any
damage before starting and operating.
Notice regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and may
include the following emission control systems: Engine Modifica-
tion (EM) and Three Way Catalyst (TWC) if so equipped.
17. Disengage all control levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments, or
inspections.
result in personal
injury. When you see
this symbol, HEED
IT’S WARNING!
Average Useful Life
18. Never put your hand in the discharge or collector openings.
Always use the clean-out tool provided to unclog the dis-
charge opening. Do not unclog chute assembly while engine
is running. Shut off engine and remain behind handles until
all moving parts have stopped before unclogging.
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20. If situations occur which are not covered in this manual, use
care and good judgment. Call customer assistance for the
name of your nearest servicing dealer.
According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years, or
60 hours of operation. At the end of the Average Useful Life,
buy a new machine or have the machine inspected annually by
an authorized service dealer to ensure that all mechanical and
safety systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: The snow thrower is shipped with oil and
WITHOUT GASOLINE. After assembly, refer to separate
engine manual for proper fuel and engine oil recom-
mendations.
3
Loose Parts
•
The augers are secured to the auger shaft with shear
pins and bow tie cotter pins. If you hit a foreign object
or ice jam, the snow thrower is designed so that the
pins may shear. Replacement shear pins and cotter
pins are provided for your convenience. Store these
Setting Up
Your Snow
Thrower
safely until needed.
Items Required For Assembly
Pair of pliers
Fresh gasoline
7/16” Wrenches or adjustables
Before Assembly
Figure 1
•
Disconnect the spark plug wire and ground it against
the engine to prevent unintended starting.
•
Reference to the right hand or left hand side of
machine are observed from the operating position.
NOTE: This Operator’s
Manual covers several
models. Snowthrower
featrues vary by model.
Not all features refer-
enced in this manual
are applicable to all
Assembling Handle
•
Look at the lower rear of the snow thrower frame to
be sure the spring (found at the end of each cable) is
attached to its actuator bracket.
•
Remove the lower handle knobs, washers and
carriage bolts from each side of the lower handle. See
Figure 2.
snowthrower models.
•
•
•
Raise the upper handle assembly until it locks over
the lower handle. See Figure 1.
NOTE: References to
right or left side of the
snow thrower are deter-
mined from behind the
unit in the operating
position.
Secure the upper handle and lower handle with the
handle knobs and carriage bolts previously removed.
Tighten the handle knobs already in place on the
upper holes and secure the handles firmly.
Figure ꢀ
Attaching Chute Crank
•
Remove the hairpin clip from the upper chute crank
and slide the upper chute crank into the lower chute
crank. A pair of pliers may help in this job. See Figure
3.
NOTE: Replacement
auger shear pins and
cotter pins are provided
for your convenience.
Store these safely until
needed.
a. Align the two holes on both chute cranks. See
Figure 3.
b. Secure with the hairpin clip removed earlier.
a
b
Figure 3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Setting Up
Your Snow
Thrower
Figure 4
Figure ꢁ
Attaching the Chute Assembly
•
•
•
Remove locknuts and screws securing one of the
flange keepers to the chute assembly. See Figure 4.
WARNING
Prior to operating
your snow thrower,
refer to Auger Control
on page 9. Read and
follow all instructions
carefully and perform
all adjustments to
verify your unit is
operating safely and
properly.
Loosen but do not remove the locknuts and screws on
the other two flange keepers.
Slide chute assembly over chute opening, making
sure the flange keepers are beneath lip of chute
adapter. The notches should engage with the spiral
end of the chute crank. See Figure 5.
•
Secure flange keeper, locknuts and screws previously
removed. Tighten all flange keepers and hardware
with two 7/16” wrenches. Do not over tighten.
NOTE: If necessary the chute crank support bracket can
be adjusted so the spiral on the chute crank fully engages
the teeth on the chute assembly. Refer to the Adjustment
Section.
Attaching the Shift Rod
•
Align the upper and lower shift rods, then slide the
shift rod connector down over the end of the lower
shift rod. Tap the connector until the lower rod is
completely through the connector. See Figure 6.
Figure 6
NOTE: If the connector is not properly assembled, the
shift rod will pivot and you will not be able to change
speeds or direction.
NOTE: If the full range of speeds (forward and reverse)
cannot be achieved, refer to the Adjustment Section.
•
Normally the cable ties holding the steering cables
against the handle are loosely installed on each side
of the lower handle at the factory. Pull the cable ties
tight to secure. Cut the excess from the ends of cable
ties.
•
•
If not already attached, slip the cables that run from
the handle panel to the discharge chute into the cable
guide located on top of the engine. See Figure 7.
Wrap the wire from the head lamp down the right
handle until the wire can be plugged into the alternator
lead wire under the fuel tank. See Figure 8.
Figure ꢂ
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Drift Cutters (If Equipped)
Drift cutters should be used when operating the snow
thrower in heavy drift conditions.
Alternator Lead
3
Alternator
Lead
•
•
•
On models so equipped, drift cutters and hardware
are assembled to the auger housing inverted.
Remove the carriage bolts and wingnuts securing the
drift cutters to the housing.
Setting Up
Your Snow
Thrower
Lamp Wire
Reposition drift cutters so they face forward as shown
in Figure 9. Secure with hardware previously removed,
wingnuts should be fastened on the outside of the
housing as shown.
NOTE: Wheels are omitted from illustration for clarity.
Figure ꢃ
If your unit is not equipped with drift cutters, you may
contact Customer Support as instructed on page 2 for
information regarding price and availability.
Snowthrower Model Drift Cutter Kit:
All models
OEM-390-679
Clean-OutTool
The clean-out tool is mounted to the rear of the auger
housing and is designed to clear a clogged chute. See
Figure 10. Refer to the Operation section for more
detailed information regarding the chute clean-out tool.
WARNING
Never use your hands
to clean snow and
ice from the chute
assembly or auger
housing.
NOTE: This item is fastened with a cable tie to the rear
of the auger housing at the factory. Cut
the cable tie before operating the snow
thrower.
WARNING: Never use your hands to
clean snow and ice from the chute assembly or auger
housing.
Figure 9
Final Adjustments
Clean-Out
Tool
Make these final adjustments before operating your snow
thrower for the first time. Failure to follow these instruc-
tions may cause damage to the snow thrower.
IMPORTANT
Under any circum-
stance do not exceed
manufacturer’s recom-
mended psi. Equal tire
pressure should be
maintained at all times.
Excessive pressure
when seating beads
may cause tire/rim
assembly to burst
Wheel Drive Control & Shift Lever
Perform the following test to determine need for adjust-
ment:
•
Move the shift lever into sixth (6) position. See Figure
14.
•
With the drive control released (see Figure 11A),
push the snow thrower forward, then pull it back. The
machine should move freely.
•
•
Engage the drive control and attempt to move the
machine both forward and back, resistance should be
felt.
Figure 10
with force sufficient to
cause serious injury.
Refer to sidewall of
tire for recommended
pressure.
Move the shift lever into the fast reverse (R2) position
and repeat the previous two steps.
If you experienced resistance rolling the unit, either
when repositioning the shift lever from 6 to R2 or when
attempting to move the machine with the drive control
released, adjust the drive control immediately. To adjust,
proceed as follows:
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
B
A
3
Setting Up
Your Snow
Thrower
Auger
Drive
Figure 11
•
Loosen the Nylock nut on the drive control cable and
unthread the cable one full turn. See Figure 13.
•
•
Recheck adjustment.
Retighten the Nylock nut to secure the cable when
correct adjustment is reached.
Figure 1ꢀ
NOTE: For more details, refer to Drive Control Adjust-
ment in the Adjustment Section of this manual.
Auger Control
WARNING
Check the adjustment of the auger control as follows:
•
When the auger control is released and in the
disengaged “up” position (see Figure 11B),
the cable should have very little slack, but
should NOT be tight. See Figure 12.
Never use your hands
to clean snow and
ice from the chute
assembly or auger
housing.
WARNING:Do not over-tighten the
cable. Over-tightening may prevent the auger from
disengaging and compromise the safety of the snow
thrower.
•
In a well-ventilated area, start the snow thrower
engine as instructed on page 12. Make sure the
throttle is set in the fast position.
Figure 13
•
•
Thread the Nylock nut outward (down the coupler)
three full turns to provide more slack in the cable and
reattach the spring to the bracket.
•
•
While standing in the operator’s position (behind the
snow thrower) engage the auger.
IMPORTANT
If the tire pressure is not
equal in both tires, the unit
may not travel in a straight
path and the shave plate
may wear unevenly.
Allow the auger to remain engaged for approximately
ten seconds before releasing the auger control.
Repeat this several times.
Repeat auger control test to verify for proper
adjustment. Repeat previous steps to adjust more, if
necessary.
•
•
With the engine running in the fast position and the
auger control lever in the disengaged “up” position,
walk to the front of the machine.
Skid Shoes
Position the skid shoes based on surface conditions.
Adjust upward for hard-packed snow. Adjust downward
when operating on gravel or crushed rock surfaces. See
“Making Adjustment” Section.
Confirm that the auger has completely stopped
rotating and shows no signs of motion.
IMPORTANT: If the auger shows any signs of rotating,
immediately return to the operator’s position and shut
off the engine. Wait for all moving parts to stop before
readjusting the auger control cable.
Tire Pressure (PneumaticTires)
The tires are over-inflated for shipping purposes.
Check the tire pressure before operating the snow
thrower. Refer to the tire side wall for tire manufacturer’s
recommended psi and deflate (or inflate) the tires as
necessary.
•
To readjust the control cable, unhook the spring
(found on the end of the auger cable) from the auger
actuator bracket. See Figure 12.
•
Push the cable coupler through the end of the spring
to expose the lock nut. See Figure 13.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
KnowYour Snow Thrower
4
Shift Lever
Chute Tilt Control
Drive Control
Operating
Your Snow
Thrower
Auger Control
Headlight
Wheel Steering
Control
Gas Cap
Oil Fill
Chute Assembly
Chute
Directional
Control
Clean-Out Tool
Engine Controls
Recoil Starter
Handle
Electric Starter Outlet
Primer
Ignition
Key
WARNING
Choke
Control
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
Throttle
Control
Skid Shoe
Figure 14
Now that you have set up your snow thrower for opera-
tion, get acquainted with its controls and features. These
are described below and illustrated on this page. This
knowledge will allow you to use your new equipment to
its fullest potential.
Choke Control
Use extreme care
when handling
gasoline. Gasoline is
extremely flammable
and the vapors are
explosive. Never fuel
the machine indoors
or while the engine
is hot or running.
Extinguish cigarettes,
cigars, pipes and
other sources of
ignition.
NOTE: For detailed starting instructions and more
information on all engine controls, refer to the separate
engine manual packed with your unit.
The choke control is found on the rear of the engine and
is activated by rotating the knob clockwise. Activating the
choke control closes the choke plate on the carburetor
and aids in starting the engine.
Shift Lever
Throttle Control
6
5
4
3
2
1
The shift lever is located in the center of
the handle panel and is used to determine
ground speed and direction of travel. It can
be moved into any of eight positions.
The throttle control is located on the
engine. It regulates the speed of the
engine and will shut off the engine when
pushed down completely.
IMPORTANT: Always release drive control
before changing speeds.
Primer
F
Depressing the primer forces fuel directly
into the engine’s carburetor to aid in
cold-weather starting.
Forward: The snow thrower has six
forward (F) speeds. Position one (1) is the
slowest and position six (6) is the fastest.
R1
R2
R
Oil Fill
Reverse: The snow thrower has two
reverse (R) speeds—R1 is the slower of
the two.
Engine oil level can be checked and oil
added through the oil fill.
34/0
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger Control
Ignition Key
The auger control is located on the left
handle. Squeeze the auger control to
engage the augers. Release to stop the
snow throwing action. The drive control
must also be released in order to stop
auger.
The ignition key must be inserted and snapped in place
in order for the engine to start. Remove the ignition key to
prevent unauthorized use of equipment. Do NOT attempt
to turn the key.
4
Chute Clean-Out Tool
WARNING: Never use your hands to
clear a clogged chute assembly. Shut off
engine and remain behind handles until
all moving parts have stopped before
unclogging.
Operating
Your Snow
Thrower
Drive Control / Auger Control Lock
The drive control is located on the right handle. Squeeze
the drive control to engage the wheel drive. Release to
stop.
This same lever also locks the auger control so you
can operate the chute crank without interrupting the
snow throwing process. If the auger control is engaged
simultaneously with the drive control, the operator can
release the auger control (on the left handle) and the
augers will remain engaged. Release the drive control to
stop the augers and wheel drive (the auger control must
also be released).
The clean-out tool is conveniently fastened to the rear of
the auger housing with a mounting clip.
1. Release both the auger control and the drive/auger
control lock.
2. Stop the engine by moving the throttle to the stop
position.
3. Remove the clean-out tool from the mounting clip.
IMPORTANT: Always release the drive control before
changing speeds.
4. Use the shovel-shaped end of the clean-out tool to
remove any snow and ice in the chute assembly.
5. Re-fasten the clean-out tool to the mounting clip on
the rear of the auger housing and restart engine.
WARNING
Two-Way Chute Control™)
This two-way control lever is meant to
control the distance of snow discharge
from the chute. Tilt the lever forward or
rearward to adjust the distance snow will
be thrown.
6. While standing in the operator’s position (behind the
snow thrower), engage the auger control for a few
seconds to clear any remaining snow or ice from the
chute assembly before continuing to clear snow.
The operation of
any snow thrower
can result in foreign
objects being thrown
into the eyes, which
can damage your
eyes severely. Always
wear safety glasses
while operating the
snow thrower, or while
performing any adjust-
ments or repairs on it.
Skid Shoes
Position the skid shoes based on surface conditions.
Adjust upward for hard-packed snow. Adjust downward
when operating on gravel or crushed rock surfaces. See
“Making Adjustment” Section.
Chute Directional Control
The chute directional control is
located on left side of the snow
thrower.
Headlight
The headlight is on whenever the engine is running.
To change the direction in which
snow is thrown, turn chute direc-
CLOCKWISE TO
DISCHARGE LEFT
tional control as follows:
•
COUNTER CLOCKWISE
TO DISCHARGE RIGHT
Crank clockwise to discharge to
the left.
Be sure no one other
than the operator is
standing near the snow
thrower while starting
engine or operating
snow thrower. Never
run engine indoors or
in enclosed, poorly
ventilated areas. En-
gine exhaust contains
carbon monoxide, an
odorless and deadly
gas. Keep hands, feet,
hair and loose clothing
away from any moving
parts on engine and
snow thrower.
•
Crank counterclockwise to
discharge to the right.
Wheel Steering Controls
The left and right wheel steering controls
are located on the underside of the
handles. Squeeze the right control to
turn right; squeeze the left control to turn
left.
NOTE: Operate the snow thrower in
open areas until you are familiar with
these controls.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Once the engine starts, immediately release starter
button.
Gas & Oil Fill-Up
Service the engine with gasoline and oil as instructed in
the separate engine manual packed separately with your
snow thrower. Read instructions carefully.
6. As the engine warms, slowly rotate the choke control
to the OFF position. If the engine falters, quickly rotate
the choke control back to FULL and then slowly into
the OFF position again.
4
Starting The Engine
1. Attach spark plug wire to spark plug. Make certain
the metal loop on the end of the spark plug wire
(inside the rubber boot) is fastened securely over the
metal tip on the spark plug.
7. When disconnecting the extension cord, always unplug
the end at the three-prong wall outlet before unplug-
ging the opposite end from the snow thrower.
Operating
Your Snow
Thrower
2. Make certain both the auger control and drive control
are in the disengaged (released) position.
Recoil Starter
1. Rotate choke control to FULL choke position (cold
engine start).
3. Move throttle control up to FAST position. Insert
ignition key into slot. Make sure it snaps into place.
Do not attempt to turn the key.
NOTE: If the engine is already warm, place choke control
in the OFF position instead of FULL.
NOTE: The engine cannot start unless the key is
inserted into ignition switch.
2. Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
Electric Starter (on certain models)
NOTE: DO NOT use primer to restart a warm engine after
a short shutdown.
1. Determine that your home’s wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
WARNING
NOTE: Additional priming may be necessary if the
temperature is below 15° F. (-9° C).
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
WARNING: The optional electric
starter is equipped with a grounded
three-wire power cord and plug, and
is designed to operate on 120 volt AC
household current. It must be used
with a properly grounded three-prong
receptacle at all times to avoid the
possibility of electric shock. Follow all
instructions carefully prior to operat-
ing the electric starter.
3. Grasp the recoil starter handle and slowly pull the rope
out. At the point where it becomes slightly harder to
pull the rope, slowly allow the rope to recoil.
4. Pull the starter handle with a firm, rapid stroke. Do not
release the handle and allow it to snap back. Keep a
firm hold on the starter handle and allow it to slowly
recoil.
Use extreme care
when handling
5. As the engine warms, slowly rotate the choke control
to the OFF position. If the engine falters, quickly rotate
the choke control back to the FULL position and then
slowly into the OFF position again.
If your home’s wiring system is not a three-wire
grounded system, do not use this electric starter under
any conditions.
gasoline. Gasoline is
extremely flammable
and the vapors are
explosive. Never fuel
the machine indoors
or while the engine
is hot or running.
Extinguish cigarettes,
cigars, pipes and
other sources of
ignition.
If your home electrical system is grounded, but a
three-hole receptacle is not available, one should
be installed by a licensed electrician before using the
electric starter.
NOTE: Allow the engine to warm up for a few minutes
after starting. The engine will not develop full power until it
reaches operating temperatures.
Stopping The Engine
Run engine for a few minutes before stopping to help dry
off any moisture on the engine.
If you have a grounded three-prong receptacle,
proceed as follows:
1. Plug the extension cord into the outlet located on
the engine’s surface. Plug the other end of extension
cord into a three-prong 120-volt, grounded, AC outlet
in a well-ventilated area.
•
•
Move throttle control to STOP position.
Remove the ignition key (Do not turn key) to prevent
unauthorized use of equipment.
2. Rotate choke control to FULL choke position (for a
cold engine start).
NOTE: Keep the key in a safe place. The engine cannot
start without the ignition key.
NOTE: If the engine is already warm, place choke
control in the OFF position instead of FULL.
•
Wipe all snow and moisture from the area around the
engine as well as the area in and around the drive
control and auger control. Also, engage and release
both controls several times.
3. Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
NOTE: DO NOT use primer to restart a warm engine
after a short shutdown.
4. Push starter button to start engine.
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
To Engage Drive
Operating Tips
1. With the engine running near top speed, move
shift lever to one of six FORWARD positions or two
REVERSE positions. Select a speed appropriate for
the snow conditions that exist.
NOTE: Allow the engine to warm up for a few minutes.
The engine will not develop full power until it reaches
operating temperature.
4
WARNING: The temperature of the
muffler and the surrounding areas may
exceed 150° F (65° C). Avoid these
areas.
2. Squeeze drive control against the right handle and
the snow thrower will move. Release it and the drive
motion will stop.
Operating
Your Snow
Thrower
1. If possible, remove snow immediately after it falls.
2. Discharge snow downwind whenever possible.
3. Slightly overlap each previous path.
To Engage Augers
1. To engage augers and start snow throwing, squeeze
the left hand auger control against the left handle.
Release to stop augers.
4. Set the skid shoes 1/4” below the shave plate for
normal usage. Adjust them upward for hard-packed
snow and downward when using on gravel or crushed
rock.
2. While the auger control is engaged, squeeze the drive
control to move, release to stop. Do not shift speeds
while the drive is engaged.
NOTE: This same lever also locks auger control so you
can turn the chute control without interrupting the snow
throwing process.
General Recommendations
1. Always observe safety rules when performing
any maintenance.
WARNING
3. Release the auger control; the interlock mechanism
should keep the auger control engaged until the drive
control is released.
2. The warranty on this snow thrower does not cover
items that have been subjected to operator abuse
or negligence. To receive full value from warranty,
operator must maintain the snow thrower as
instructed here.
The muffler, engine
and surrounding
areas become hot
and can cause a burn
150°F (65°C). Do not
touch.
4. Release the drive control to stop both the augers and
the wheel drive. To stop the auger, both levers must
be released.
3. Some adjustments will have to be made periodically
to maintain your unit properly.
4. Periodically check all fasteners and make sure these
NOTE: Use slower
speeds in higher
snow and/or until you
are familiar with the
snow thrower opera-
IMPORTANT
NEVER move the
shift lever without first
releasing the wheel
drive control. Doing so
will cause premature
wear on the drive
system’s friction wheel.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ
Making
Adjustments
Figure 1ꢁ
Shift Rod
WARNING
If the full range of speeds (forward and reverse) cannot
be achieved, refer to Figure 15 and adjust the shift rod
as follows:
Figure 16
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
1. Looking underneath the handle panel, note which
of the three holes in the shift lever the ferrule is
inserted into. Also note the direction of insertion.
Then remove the internal cotter pin and flat washer
from the ferrule and withdraw the ferrule from the
shift lever. See Figure 15.
Friction
Wheel
2. Place shift lever in sixth (6) position or fastest
forward speed.
Never attempt to
make any adjust-
ments while the
engine is running,
except where speci-
fied in operator’s
manual.
3. Push shift rod and shift arm assembly down sharply,
as far as it will go to put the drive into the fastest
forward position.
Drive
Plate
Axle Supp.
Brkt.
4. As necessary, rotate the ferrule up or down the shift
rod until the ferrule lines up with the hole from which
it was earlier removed. See Figure 15.
Opening
5. From the direction noted earlier, insert the ferrule
into the proper hole.
Figure 1ꢂ
6. Reinstall the washer and the internal cotter pin.
5. With the drive control lever engaged, check if the
friction wheel solidly contacts the drive plate. See
Figure 17. If not, adjust as follows:
Drive Control
Refer to the Final Adjustment section of the Set-Up
instructions to adjust the drive control. To further check
the adjustment, proceed as follows:
a. Loosen the jam nut on the traction drive cable and
thread the cable in or out as necessary.
1. Drain the gasoline out of your snow thrower’s engine,
and place a piece of plastic film under the gas cap to
avoid spillage.
b. Retighten the jam nut to secure the cable when
correct adjustment is reached.
6. Reassemble the frame cover.
2. Tip the snow thrower forward, allowing it to rest on
the auger housing.
NOTE: If you placed plastic film under the gas cap earlier,
remove it now.
3. Remove the frame cover underneath the snow
thrower by removing the self-tapping screws. See
Figure 16.
4. With the wheel drive control released, check if there
is clearance between friction wheel and drive plate in
all positions of the shift lever. See Figure 17.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Skid Shoes
The space between the shave plate and the ground can
be adjusted by raising or lowering the skid shoes.
For close snow removal, as when using on a smooth
concrete or asphalt driveway, place the skid shoes in the
low position. Use the middle or high position when the
area to be cleared is uneven. When operating on gravel,
always put skid shoes in the high position.
See Figure 18.
ꢁ
Making
Adjustments
Adjust skid shoes as follows:
1. Loosen, but do not remove, the hex flange locknuts
which fasten the skid shoe to the auger housing.
2. Raise or lower the skid shoe to desired position.
3. Retighten the hex nuts loosened earlier.
NOTE: Make certain the bottom surface of skid shoe is
flat against the ground to avoid uneven wear.
Figure 1ꢃ
IMPORTANT: It is not
recommended that you
operate this snow thrower
on gravel as loose gravel
can be easily picked up
and thrown by the auger
causing personal injury
or damage to the snow
thrower.
4. Repeat on the other side of the snow thrower.
Auger Control
Refer to instructions on page 9 to adjust the auger
control. Make certain to check for correct adjustment as
instructed before operating the snow thrower.
Chute Assembly
The distance snow is thrown can be adjusted by adjusting
the angle of the chute assembly. Refer to page 9 for
instructions.
The remote chute control cables have been pre-adjusted
at the factory. Move the remote chute lever on the control
panel back and forward to adjust angle of the chute
assembly.
If for some reason, you
have to operate the snow
thrower on gravel, keep
the skid shoe in the high-
est position for maximum
clearance between the
ground and the shave
plate.
Chute Bracket Adjustment
If the spiral at the bottom of the chute directional control
is not fully engaging with the chute assembly, the chute
bracket can be adjusted. To do so:
Figure 19
1. Loosen the two nuts which secure the chute bracket
and reposition it slightly. See Figure 19.
2. Retighten the nuts.
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Lubrication
Drive and Shifting Mechanism
At least once a season or after every 25 hours of opera-
tion, remove rear cover. Lubricate any chains, sprockets,
gears, bearings, shafts, and the shifting mechanism at
least once a season. Use engine oil or a spray lubricant.
Refer to Figure 20.
Gear
(Hex)
Shaft
6
Friction
Wheel
Maintaining
Your Snow
Thrower
IMPORTANT: Keep all grease and oil off the rubber
friction wheel and drive plate.
Wheels
At least once a season, remove both wheels. Clean and
coat the axles with a multipurpose automotive grease
before reinstalling wheels.
Drive
Plate
Auger Shaft
At least once a season, remove the shear pins on auger
shaft. Spray lubricant inside shaft, around the spacers.
Also lubricate the flange bearings found at either end of
the shaft. See Figure 21.
Figure ꢀ0
WARNING
Augers
Grease
Fitting (optional)
Vent Plug
Shear Pin
•
The augers are secured to the spiral shaft with shear
pins and cotter pins. If the auger should strike a
foreign object or ice jam, the snow thrower is designed
so that the pins may shear. See Figure 21.
Always stop engine,
disconnect spark
plug, and ground
against engine before
cleaning, lubricating
or doing any kind of
maintenance on your
machine.
Auger Shaft
•
If the augers will not turn, check to see if the pins have
sheared. One set of replacement shear pins has been
provided with the snow thrower. When replacing pins,
spray an oil lubricant into shaft before inserting new
pins.
Shave Plate and Skid Shoes
Cotter Pin
Spacers
Bearing
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when necessary.
To remove skid shoes:
Figure ꢀ1
IMPORTANT
Avoid oil spillage on
rubber friction wheel
and aluminum drive
plate.
1. Remove the carriage bolts (and washers if
equipped)and hex flange nuts which secure the skid
shoes to the snow thrower.
2. Reassemble new skid shoes with previously removed
hardware. Refer to Figure 22.
To remove shave plate:
1. Remove the carriage bolts and hex nuts which attach
it and the skid shoes to the snow thrower housing.
2. Reassemble new shave plate, making sure heads of
carriage bolts are to the inside of housing. Tighten
securely.
Figure ꢀꢀ
Engine
Refer to the separate engine manual packed with your
unit for all engine maintenance and lubrication instruc-
tions.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove the plastic belt cover, located near the
engine, by removing the three self-tapping screws
that secure it. See Figure 23.
Replacing Belts
To remove and replace either the auger belt or the drive
belt, follow the steps below and then proceed to the
specific steps listed under respective sub-headings.
3. a. Loosen the bolt shown in Figure 24 securing the
belt keeper bracket and remove the other bolt.
b. Push the belt keeper and bracket up off the
engine pulley. See Figure 25.
6
1. Disconnect the chute crank assembly at the discharge
chute end by removing the hairpin clip and the flat
washer. See Figure 19.
Maintaining
Your Snow
Thrower
Auger Belt
4. Remove the hairpin clip and flat washer from the
ferrule in order to disconnect the auger idler rod from
the brake bracket assembly. See Figure 26.
5. Unhook the spring found on the end of the auger
cable from its respective actuator bracket. Refer to
Figure 12.
6. Slip the auger control belt (the front belt) off the
engine pulley.
7. Pull the brake bracket assembly towards the cable
guide roller and unhook the auger cable “Z” fitting.
See Figure 27.
IMPORTANT
NEVER replace the
auger shear pins with
standard pins. Any
8. Remove the upper bolts which attach the auger
housing assembly to the frame assembly using a 1/2”
wrench. Refer to Figure 28.
damage to the auger
gearbox or other com-
ponents, as a result of
doing so, will NOT be
covered by your snow
thrower’s warranty.
Figure ꢀ3
Remove
Check the condition
of both auger belt and
drive belt every 25
hours of snow thrower
operation. Replace if
either shows signs of
wear and tear.
Loosen
Figure ꢀ4
Specifications are
subject to change
Figure ꢀ6
without notification or
obligation. Images may
not reflect your exact
model and are for refer-
ence purposes only.
Figure ꢀꢂ
Figure ꢀꢁ
1ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Maintaining
Your Snow
Thrower
Figure ꢀ9
Figure ꢀꢃ
9. Place a block of wood underneath the auger housing
as shown in Figure 29 and separate auger housing
from the frame by tilting the housing forward and
pulling up the handles.
B
10.a. Using a 1/2” wrench, remove the hex screw and
washer from the center of the pulley on the auger
housing. See Figure 30.
WARNING
Always stop engine,
disconnect spark
plug, and ground
against engine before
cleaning, lubricating
or doing any kind of
maintenance on your
machine.
b. Lift the brake bracket assembly out of the pulley
groove
C
c. Remove the pulley.
11. Remove and replace auger belt inside belt keepers.
A
12. Apply Loctite 262 to the threads of the hex screw
used for mounting the auger pulley.
13.Reassemble pulley to auger housing with hex screw
and washer. Torque hex screw 250-325 in. lbs.
Figure 30
NOTE: Make sure the brake puck is seated in the pulley
groove.
1
3
If also replacing the drive belt, proceed to the “Drive Belt”
instruction. If not, reassemble by performing the previous
steps in the opposite order and manner of removal.
Proper Adjustment: With the auger clutch lever in the
disengaged position, the top surface of the new belt
should be even with the outside diameter of the pulley.
1. To adjust, disconnect ferrule from brake bracket as-
sembly and thread ferrule in (towards idler) to increase
tension on belt, and out to decrease tension.
IMPORTANT
Refer to the Final
2
Adjustment section of
the Set-Up instructions
after replacing drive
and auger belts.
NOTE: The brake puck must always be firmly seated in
the pulley groove when auger control is disengaged.
Drive Belt
1. Pull the idler pulley away from the backside of the
drive belt to relieve the tension and slide the drive belt
off the idler pulley. See Figure 31.
Figure 31
3. Install the new belt on the pulleys in the reverse order
and re-tension with the idler pulley.
2. Remove the belt from the bottom drive pulley and the
engine pulley.
Reassemble your unit by performing the previous steps in
the opposite order.
1ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Friction Wheel
Rubber
•
Drain the gasoline from the snow thrower,
or place a piece of plastic under the gas
cap.
Friction
Wheel
Assembly
6
•
•
Tip the snow thrower up and forward, so
that it rests on the housing.
Remove hex
screw and
washer
Slide
hex shaft
Maintaining
Your Snow
Thrower
Remove screws from the frame cover
underneath the snow thrower. See Figure
16.
Hex Shaft
•
•
Remove the right wheel from the axle.
Using a 3/4” wrench, hold the hex shaft
and remove the hex bolts and cupped
washer and bearing from left side of the
frame. Refer to Figure 32.
•
Holding the friction wheel assembly, slide
the hex shaft out of the right side of the
unit. The spacer on the left side of the
hex shaft will fall and the sprocket should
remain hanging lose in the chain.
Figure 3ꢀ
•
•
Lift the friction wheel assembly out between the axle
shaft and the drive shaft assemblies.
WARNING
Remove four screws securing the friction wheel rubber
between the friction wheel plates. See Figure 33.
Discard old rubber.
The rubber on the fric-
tion wheel is subject
to wear and should be
checked after the first
25 hours of operation,
and periodically
thereafter. Replace
the friction wheel
rubber if any signs of
wear or cracking are
found.
•
•
Reassemble the new friction wheel rubber to the
friction wheel assembly, tightening the four screws
in rotation and with equal force. It is important to as-
semble the rubber on the friction wheel symmetrically
for proper functioning.
Insert the pin from the shift arm assembly into the
friction wheel assembly and hold assembly in position.
Refer to Figure 34.
Friction Wheel
•
•
Slide the hex shaft through the right side of the
housing and through the friction wheel assembly.
Figure 33
Insert the hex shaft through the sprocket and the
spacer. Make certain that the chain engages both the
large and the small sprocket.
NOTE: If the sprocket fell from the snow thrower while
removing the hex shaft, place the sprocket on the hex
shaft. Position the hex hub of the sprocket toward the fric-
tion wheel when sliding the sprocket on to the hex shaft.
•
Secure with the cupped washer and hex bolt removed
earlier.
•
Secure the frame cover with self-tapping screws.
Put the snow thrower down to its normal operating
position.
NOTE: If you placed plastic film under the gas cap, be
certain to remove it.
Figure 34
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Observe the following, when preparing your snow thrower
for off-season storage:
•
Drain fuel into an approved container outdoors, away
from any open flame. Allow engine to cool. Extinguish
cigarettes, cigars, pipes and other sources of ignition
prior to draining fuel. Fuel left in engine during warm
weather deteriorates and will cause serious starting
problems.
ꢂ
Off-Season
Storage
•
If unit is to be stored over 30 days, prepare for storage
as instructed in the separate engine manual packed
with your unit.
•
•
Run engine until fuel tank is empty and engine stops
due to lack of fuel.
Remove gasoline from carburetor and fuel tank to
prevent gum deposits from forming on these parts and
causing possible malfunction of engine.
•
•
Drain carburetor by pressing upward on bowl drain,
located below the carburetor cover.
WARNING
Fuel stabilizers, such as STA-BIL®, are an acceptable
alternative in minimizing the formation of fuel gum
deposits during storage. Do not drain carburetor if
using a fuel stabilizer.
Never store snow
thrower with fuel
in tank indoors or
in poorly ventilated
areas, where fuel
fumes may reach an
open flame, spark
or pilot light as on a
furnace, water heater,
clothes dryer or gas
appliance.
•
•
Wipe equipment with an oiled rag to prevent rust.
Remove spark plug and pour one ounce of engine oil
through spark plug hole into cylinder. Cover spark plug
hole with rag. Crank engine several times to distribute
oil. Replace spark plug.
•
•
Follow the lubrication recommendations found in the
Maintenance Section.
Always store the snow thrower in a clean, dry area.
Drain fuel into an
approved container
outdoors, away from
any open flame. Be
certain engine is
cool. Do not smoke.
Fuel left in engine
during warm weather
deteriorates and will
cause serious
starting problems.
Do not drain
carburetor if
using fuel stabilizer.
Never use engine or
carburetor cleaning
products in the fuel
tank or permanent
damage may occur.
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Engine fails to start
Cause
1. Choke not in ON position.
2. Spark plug wire disconnected.
3. Fuel tank empty or stale fuel.
4. Engine not primed.
Remedy
1. Move choke to ON position.
2. Connect wire to spark plug.
3. Fill tank with clean, fresh gasoline.
ꢃ
4. Prime engine as instructed in
“Operating Your Snow Thrower”.
Trouble-
Shooting
5. Clean, adjust gap, or replace.
6. Clean fuel line.
5. Faulty spark plug.
6. Blocked fuel line.
7. Insert key fully into the switch.
8. Open fuel shut-off valve.
7. Safety key not in ignition on engine.
8. Fuel shut-ff valve closed. (If Equipped)
1. Unit running on CHOKE.
1. Move choke lever to OFF position.
Engine runs erratic
2. Clean fuel line; fill tank with clean,
fresh gasoline.
2. Blocked fuel line or stale fuel.
3. Water or dirt in fuel system.
4. Carburetor out of adjustment.
NOTE: This section
addresses minor
service issues. For
further details,
3. Drain fuel tank. Refill with
fresh fuel.
4. Contact Service Center.
contact customer
assistance.
1. Carburetor not adjusted properly.
1. Loose parts or damaged auger.
1. Contact Service Center.
Engine overheats
1. Stop engine immediately and
disconnect spark plug wire. Tighten
all bolts and nuts. If vibration
continues, have unit serviced by a
Service Center.
Excessive
Vibration
Loss of power
1. Spark plug wire loose.
2. Gas cap vent hole plugged.
3. Exhaust port plugged.
1. Connect and tighten spark plug
wire.
2. Remove ice and snow from gas
cap. Be certain vent hole is clear.
3. Contact Service Center.
1. Drive control cable in need of adjust-
ment.
1. Adjust drive control cable. Refer to
“Adjustments”.
Unit fails
to propel itself
2. Drive belt loose or damaged.
2. Replace drive belt.
1. Chute assembly clogged.
Unit fails
to discharge snow
1. Stop engine immediately and
disconnect spark plug wire. Clean
chute assembly and inside of
auger housing with clean-out tool
or a stick.
2. Foreign object lodged in auger.
2. Stop engine immediately and
disconnect spark plug wire.
Remove object from auger with
clean-out tool or a stick.
3. Auger control cable in need of adjust-
ment.
3. Refer to “Auger Control Test” .
4. Refer to Maintenance section.
5. Replace with new shear pin(s).
4. Auger belt loose or damaged.
5. Shear pin(s) sheared.
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
FOURYEAR SUPREME WARRANTY:
For four years from date of retail purchase within Canada, MTD PRODUCTS LIMITED will,
at its option, repair or replace, for the original purchaser, free of charge, any part or parts
found to be defective in material or workmanship. This warranty covers units which have
been operated and maintained in accordance with the owner’s instructions furnished with the
unit, and which have not been subject to misuse, abuse, commercial use, neglect, accident
improper maintenance or alteration. Normal wear parts or components thereof are subject to
special terms as noted below in the Ninety Day Consumer Warranty clause.
9
Warranty
The engine, starter motor or component parts thereof carry separate warranties from their
manufacturers. Please refer to the applicable manufacturer’s warranty policy for these items.
Ninety Day Consumer Warranty on Normal Wear Parts: All normal wear part failures
will be covered on this product for a period of 90 days. After 90 days but within the four year
warranty period, normal wear part failures will be covered if caused by defects in material or
workmanship of other component parts. Normal wear parts are defined as batteries, belts,
blades, blade adaptors, grass bags, rider deck wheels, seats, tires and clutch parts (friction
wheels).
Failure to comply
with suggested
maintenance
and lubrication
specifications will
void warranty.
Full Ninety Day Warranty on Battery (if equipped): For ninety (90) days from the
date of retail purchase, if any battery included with this unit proves defective in material
or workmanship and our testing determines the battery will not hold a charge, MTD
PRODUCTS LIMITED will replace the battery at no charge to the original purchaser.
Additional Limited Thirty Day Warranty on Battery (if equipped): After ninety (90) days
but within one hundred twenty (120) days from the date of purchase, MTD PRODUCTS
LIMITED will replace the defective battery, for the original purchaser, for a cost of one-half
(½) of the current retail price of the battery in effect at the date of return.
Personal use: THE FOREGOING PARAGRAPHS CONSTITUTE THE MANUFACTURER’S
ENTIRE WARRANTY WITH RESPECT TO ANY PRODUCT PURCHASED AND USED
FOR PERSONAL FAMILY, HOUSEHOLD/RESIDENTIAL PURPOSES, AS DISTINGUISHED
FROM COMMERCIAL USAGE.
Commercial use: ALL APPLICATIONS OTHER THAN PERSONAL USE AS OUTLINED
ABOVE, ARE CONSIDERED COMMERCIAL USAGE.
New products purchased for commercial usage are warranted in the same manner and to the
same extend EXCEPT the term of warranty will be 90 DAYS from date of purchase.
How to Obtain Service: Warranty service is available, with proof of purchase, through
your local MTD Authorized Service Dealer. If you do not know the dealer in your area,
please write to the Service Department of MTD PRODUCTS LIMITED, P.O. BOX 1386,
KITCHENER, ONTARIO N2G 4J1. The return of a complete unit will not be accepted by the
factory unless prior written permission has been extended by MTD PRODUCTS LIMITED.
Other Warranties: All other warranties, express or implied, including any implied warranty
of merchantability is limited in its duration to that set forth in this express limited warranty.
The provisions as set forth in this warranty provide the sole and exclusive remedy of MTD
PRODUCTS LIMITED obligations arising from the sale of its products. MTD PRODUCTS
LIMITED will not be liable for incidental or consequential loss or damage.
12.08.06
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
For parts and/or
accessories refer to
customer support on
page 2.
Adressez-vous au
«Service après-vente»
à la page 2 pour
ce qui concerne
les pièces et/ou
accessoires.
ꢀ3
Download from Www.Somanuals.com. All Manuals Search And Download.
|