Owner’s Manual
Full Motion
Flat Screen Wall Mount
MODEL: DWM1737MN
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
75x75/100x100
200x100/200x200
42”
52.1kg
(115lbs)
MAX
MAX
Русскоязычная версия настоящего руководства представлена на веб-сайте компании
Copyright © 2013 Tripp Lite. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-231-9332A1-EN.indd
1
10/31/2013 11:50:15 AM
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to
4mm Allen Key (x1)
DWM1737MN (x1)
Package M
M4X14 (x4)
M5X14 (x4)
M6X14 (x4)
M8X20 (x4)
D5 Washer (x4)
D8 Washer (x4)
Small Spacer (x8)
Package W
Anchor Bolt (x3)
Concrete Anchor (x3)
D6 Washer (x3)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-231-9332A1-EN.indd
3
10/31/2013 11:50:16 AM
1. Separate the VESA Plate from the Wall Mount
2a. Mount on Wood Stud Wall
Find and mark
1
2
3
the exact
location of
mounting holes
Drill pilot holes
D6 Washer
Anchor Bolt
Screw the wall
plate onto the
wall
WARNING
• Make sure that mounting screws are anchored into the center of the studs.
Use of a stud finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-231-9332A1-EN.indd
4
10/31/2013 11:50:16 AM
2b. Mount on Solid Brick and Concrete Block
Find and mark the
exact location of
mounting holes
1
2
Drill pilot holes
D6 Washer
Concrete Anchor
Anchor Bolt
Screw the wall
plate onto the
wall
WARNING
• When installing wall mounts on cinder block, verify the actual concrete thickness
is at least 1-3/8” (35mm) for using the concrete anchors. Do not drill into mortar
joints! Be sure to mount in a solid part of the block, generally 1” (25mm) minimum
from the side of the block. It is suggested an electric drill on a slow setting be used
to drill the hole instead of a hammer drill to avoid breaking out the back of the hole
when entering a void or cavity.
• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-231-9332A1-EN.indd
5
10/31/2013 11:50:18 AM
3. Install VESA Plate
TV
TV
TV
TV
M4X14 / M5X14
M6X14 / M8X20
D5 Washer
D8 Washer
Top of TV
or
M8X20
D5 Washer
Small Spacer
Top of TV
M8X20
D5 Washer
Small Spacer
Small Spacer
Note: Choose appropriate screws, washers and spacers (if necessary) according to the type of screen.
Screw VESA plate onto the TV.
Tighten all screws but do not over tighten.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-231-9332A1-EN.indd
6
10/31/2013 11:50:18 AM
4. Hang TV onto the Wall Plate
• Level the TV.
• Reattach the lower flat nut (removed in step 1) and tighten both nuts.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-231-9332A1-EN.indd
7
10/31/2013 11:50:20 AM
5. Adjustment
4mm Allen Key
Because the weight of displays vary, it is necessary to
slightly tighten or loosen the adjustment screw with the
supplied Allen Key.
80°
+15°
-15°
-4°
+4°
Adjust to the desired location or tilt.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
13-09-231 93-32A1_RevA
8
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-231-9332A1-EN.indd
8
10/31/2013 11:50:22 AM
|