ANTY
TION
ripp Lite
A
Owner’s Manual
ARR
W
REGISTR
.tripplite.com/warranty
Register online today for a
chance to win a FREE T
product www
HDMI Matrix Switch
Models: B119-2X2, B119-4X4
Package Contents
Product Features
2
2
Mounting
3
Standard Installation
RS-232 Serial Control
Troubleshooting
4
6
9
Warranty & Warranty Registration
10
Copyright © 2013 Tripp Lite. All rights reserved.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
13-08-038-9332BC.indd
1
8/5/2013 12:26:35 PM
Mounting
The B119-2X2 and B119-4X4 come with mounting hardware that allows
them to be mounted in a variety of ways. The following images show
the different ways the included mounting brackets can be attached for
different mounting methods.
Note: The images below show a B126-1A1 HDMI over Cat5 Receiver Unit, but the mounting
hardware installation is the same for the B119-2X2 and B119-4X4.
Wallmount 1
Wallmount 2
19” Rackmount
Pole Mount
3
Download from Www.Somanuals.com. All Manuals Search And Download.
13-08-038-9332BC.indd
3
8/5/2013 12:26:36 PM
Standard Installation
Note:
1. The diagram below shows a B119-2X2 installation, but installation will be the same for the
B119-4X4, except for the number of ports.
2. The back panel of the B119-4X4 contains an IR port which has been capped off. This port is
intended for future use, and does not currently function.
B119-2x2
(Optional)
Up to 16 ft.
Up to 25 ft.
Up to 25 ft.
Blu-Ray™
Up to 16 ft.
1
2
Make sure all devices being connected are turned off.
Optional: Connect the 3.5 mm to DB9 adapter to the RS-232 serial
port on the switch, and then to the DB9 serial port on the computer
you will be using to control it with.
3
Connect the first HDMI source to the port on the switch marked
Source A.
Note: The HDMI cable connecting the source to the switch must be no longer than 16 ft.
4
5
Repeat step 3 to connect additional HDMI sources to the remaining ports.
Connect the external power supply to the switch and plug it into
a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU), or
Uninterruptible Power Supply (UPS). When receiving power, the
following LEDs will illuminate: The Green Power LED and Orange
Source LEDs (for the Source ports that have devices connected to
them). A Green LED will also illuminate to indicate the source that is
being transmitted to each Output port.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
13-08-038-9332BC.indd
4
8/5/2013 12:26:37 PM
Standard Installation
6
Connect the first HDMI display to the port on the switch marked
Output 1.
Note: The HDMI cable connecting the switch to a display must be no longer than 25 ft.
7
8
Repeat step 6 to connect additional displays to the remaining ports.
Turn on the power to the connected devices. The video image should
now be displayed on the connected monitors.
9
Press the switch next to each set of Output LEDs to switch the source
being displayed on the corresponding Output monitor. You can also use
the included remote control to switch between sources. As with the
switch next to the Output LEDs, press the button on the remote control
of the desired Output port to switch the source being displayed.
Note: The same 4 button remote control comes with both the B119-2X2 and B119-4X4.
Buttons 3 and 4 will not be used for the B119-2X2.
See the RS-232 Serial Control section in this manual for details on
controlling the switch using Terminal Emulation Software.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
13-08-038-9332BC.indd
5
8/5/2013 12:26:37 PM
RS-232 Serial Control
Before using RS-232 Serial Control, you must first go into your Terminal
Emulation Software and update the COM port settings.
1
Go to the Setup drop-down menu and select the Serial Port option.
2
Select the COM port that is being used, and update the remaining
settings as follows: Baud Rate (57600), Data (8 bit), Parity (none),
Stop (1 bit), Flow Control (none).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
13-08-038-9332BC.indd
6
8/5/2013 12:26:38 PM
RS-232 Serial Control
3
Next, you will need to configure your software to allow input control.
Go to the Setup drop-down menu and select the Terminal option.
4
Update the following settings; Receive (LF), Local Echo (enable). The
remaining settings can stay as they are.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
13-08-038-9332BC.indd
7
8/5/2013 12:26:38 PM
RS-232 Serial Control
5
Once these settings are updated, the Terminal Emulation Software
will recognize the switch, allowing you to enter commands to control it
with. The following table lists the available commands.
Command
Action
sw[x] [n]
Switches the source being displayed on the selected
output. [x] is the output (1, 2, 3, or 4) and [n] is the
desired source (A, B, C, or D). For example, a command
of sw1 2 would display source 2 on output 1.
PWD
STE
Turns power to the switch on/off.
Displays the current output state, showing which source
is being displayed on each output.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
13-08-038-9332BC.indd
8
8/5/2013 12:26:38 PM
Troubleshooting
If you are unable to get an acceptable image after following the
installation instructions, try the troubleshooting tips below.
1
Is the external power supply that came with the product connected
and plugged into a working power source? For the product to function
properly, it must be connected to and receiving power from the
external power supply.
2
3
Was the power to the connected devices turned off prior to
installation? If not, restart them.
What type of cabling are you using? Inferior cabling can result in poor
performance, so it is important that you use cables that can support
the video resolution you are trying to obtain. It is recommended
that you use Tripp Lite’s P568-Series High-Speed HDMI cables, as
they have been tested to work with the B119-Series Matrix Switch
products.
4
5
6
Test your cables to ensure they are working properly. For example,
connect your HDMI cables between a source and monitor that you
know works to see if the cable is functioning.
Is the switch located in an area that exposes it to higher
temperatures? If the product is overheated, it will not function
properly.
What length HDMI cable are you using? The cable connecting a HDMI
source to the switch must be no longer than 16 ft. in length. The
cable connecting the switch to a display must be no longer than
25 ft. in length.
7
8
If you are having trouble getting your Terminal Emulation Software to
recognize the switch, you may need to shut down your installation
and start from the beginning. The 3.5 mm to DB9 adapter cable must
be connected first; otherwise the switch will not be recognized.
If you are still having trouble getting your Terminal Emulation Software
to recognize the switch, check to make sure that your serial settings
are set according to the instructions in the RS-232 Serial Control
section of this manual.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
13-08-038-9332BC.indd
9
8/5/2013 12:26:38 PM
Warranty & Warranty Registration
1-Year Limited Warranty
TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period
of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is
limited to repairing or replacing (at its sole option) any such defective products. To obtain service
under this warranty, you must obtain a Returned Material Authorization (RMA) number from
TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE
or an authorized TRIPP LITE service center with transportation charges prepaid and must be
accompanied by a brief description of the problem encountered and proof of date and place of
purchase. This warranty does not apply to equipment which has been damaged by accident,
negligence or misapplication or has been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid
limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS
PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is
not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of
equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or
otherwise.
WARRANTY REGISTRATION
You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
FCC Notice, Class B
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this equipment not expressly approved by Tripp Lite could void the
user’s authority to operate this equipment.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
13-08-038-9332BC.indd 10
8/5/2013 12:26:38 PM
Warranty & Warranty Registration
WEEE Compliance Information for Tripp Lite Customers and Recyclers
(European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and
implementing regulations, when customers buy new electrical and electronic equipment
from Tripp Lite they are entitled to:
• Send old equipment for recycling on a one-for-one, like-for-like basis
(this varies depending on the country)
• Send the new equipment back for recycling when this ultimately becomes waste
WARNING
Use of this equipment in life support applications where failure of this equipment can reasonably
be expected to cause the failure of the life support equipment or to significantly affect its safety
or effectiveness is not recommended. Do not use this equipment in the presence of a flammable
anesthetic mixture with air, oxygen or nitrous oxide.
Tripp Lite follows a policy of continuous improvement. Product specifications are subject to change
without notice.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
13-08-038-9332BC.indd 11
8/5/2013 12:26:38 PM
13-08-038 • 93-32BC_revB
12
Download from Www.Somanuals.com. All Manuals Search And Download.
13-08-038-9332BC.indd 12
8/5/2013 12:26:38 PM
|