Tripp Lite Switch B004 VPA2 K R User Manual

Push Button Switching  
Introduction  
The built-in push buttons allow you to directly control  
switching between computers. Simply press the button  
to switch computer ports. By default, Audio/Mic and PC  
Switching are simultaneous. To disable this feature, use the  
hot key sequence ScrLk + ScrLk + W.  
The B004-VPA2-K-R is a 2-port compact PS/2 KVM Switch  
with optional audio and microphone switching function.  
It allows you to access, control, boot and reboot multiple  
PS/2-enabled computers using a single keyboard, monitor,  
mouse console and optional speaker set and microphone.  
The B004-VPA2-K-R also offers user-programmable  
simultaneous/independent switching of applications. For  
users who need to use a hot key sequence other than the  
pre-programmed scroll locks, it also offers five hot key  
configuration alternatives.  
Owner’s Manual  
(See Quick Reference Guide.)  
Keyboard Hot Key Switching  
A keyboard hot key sequence consists of at least three  
specific keystrokes. (See Quick Reference Guide.)  
Hot key sequence: [ScrLk]* + [ScrLk]* + command key(s)  
* User-definable: Scroll Lock, Caps, Esc, F12 or Num Lock.  
Installation  
The KVM Switch is a plug-and-play device, eliminating the  
need to configure the KVM Switch before installation.  
Hot Key Sequence Configuration  
For users who want to use a sequence other than the two  
consecutive Scroll Locks, the B004-VPA2-K-R offers an  
additional convenient sequence configuration option.  
2-Port Compact  
Note: Before connecting the KVM Switch to the computers,  
make sure all connected computers are powered-off.  
Otherwise, the computers will not be able to recognize the  
connected keyboard and mouse.  
PS/2 KVM Switch  
Step 1. Hit Scroll Lock + H (two beeps will signal readiness  
for new sequence selection). Or press and hold down  
the last push button (Port Selection Button) until you  
hear two beeps and then release the button.  
Step 2. Select and press the key you would like to use as  
your sequence (Scroll Lock, Caps, Esc, F12 or  
Num Lock keys are available for selection) and  
you’ll hear a beep for selection confirmation. Now  
you can use the new sequence to execute your hot  
key commands.  
with Audio  
Step 1. Make sure all computers that are to be connected  
to the KVM Switch and their peripherals are  
in a powered-off state. If not, power them off before  
you proceed with the following steps.  
Step 2. Connect the shared PS/2 keyboard, mouse, monitor,  
speaker set and microphone to the KVM Switch.  
Step 3. Connect each of your computers to the KVM  
Switch using the included KVM and audio/  
microphone cables.  
Step 4. Power-up the connected computers. After your  
computers are powered up, the keyboard and  
mouse will automatically be recognized. The KVM  
Switch should now be powered-up. You can now  
begin operating the KVM Switch.  
Model: B004-VPA2-K-R  
Each keystroke within a hot key sequence should be  
pressed within 2 seconds. Otherwise, the hot key sequence  
will not be valid.  
For detailed hot key sequences and their corresponding  
functional commands, please refer to the Quick Reference  
Guide on the other side of this manual.  
Operation  
1
2
1111 W. 35th Street, Chicago, IL 60609 USA  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Texas Instruments Barcode Reader TMS470R1x User Manual
Toshiba Camcorder P20 User Manual
Toshiba Car Stereo System E6580772 User Manual
Trane Air Conditioner PTEC0701GCA User Manual
Triarch Indoor Furnishings 25612 User Manual
Tricity Bendix Oven TBF 610 User Manual
Tripp Lite Network Cables N007 025 GY User Manual
Tripp Lite Welding System 200712159 93 2768 RV User Manual
Tyco Motorized Toy Car 35464 1920 User Manual
Vermont Casting Gas Grill CF9030 User Manual