User’s Guide
CSEFE10xx-10x
Slide-in-Module Media Converter
• Switchable Ethernet and Fast Ethernet
• 10 Mb/s Copper to Fiber
• 100 Mb/s Copper to Fiber
Transition Networks CSEFE10xx-10x series Ethernet /
Fast Ethernet media converter is designed to be
installed in a Transition Networks PointSystem™
chassis and is a 10Mbps or 100Mbps switch-selectable
media converter.
Both the copper and fiber links operate at the same speed setting via a hard set with
a dip switch, so the media converter operates at either 10 Mb/s copper to fiber or
100 Mb/s copper to fiber.
Part Number
Port One - Twisted-Pair
Copper
Port Two - Fiber Optic
CSEFE1012-100 RJ-45, 100 m (328 ft)*
CSEFE1014-100 RJ-45, 100 m (328 ft)*
CSEFE1015-100 RJ-45, 100 m (328 ft)*
CSEFE1022-100 RJ-45, 100 m (328 ft)*
CSEFE1029-100 RJ-45, 100 m (328 ft)*
CSEFE1029-101 RJ-45, 100 m (328 ft)*
ST, 1310 nm single mode
duplex fiber, 20 km (12.4 miles)*
SC, 1310 nm single mode
duplex fiber, 20 km (12.4 miles)*
SC, 1310 nm single mode
duplex fiber, 40 km (24.8 miles)*
ST, 1310 nm single mode
duplex fiber, 40 km (24.8 miles)*
SC, 1310 mn (TX)/1550 nm (RX)
single fiber, 20 km (12.4 miles)*
SC, 1550 mn (TX)/1310 nm (RX)
single fiber, 20 km (12.4 miles)*
The CSEFE10xx-10x media converter is designed to be installed in pairs, where
one is the local media converter and the other is the remote. For example, a local
CSEFE1011-100 converter is connected, via fiber, to a remote CSEFE1011-100
converter.
For a single fiber network, a local CSEFE1029-100 is connected, via fiber, to a
remote CSEFE1029-101 converter.
* Typical maximum cable distance.
Actual distance is dependent upon the
physical characteristics of the network.
(TX) = transmit, (RX) = receive
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .5
Cable Specifications . . . . . . . . . . .6
Technical Specifications . . . . . . . .8
Troubleshooting . . . . . . . . . . . . . .9
Compliance Information . . . . . . .12
Download from Www.Somanuals.com. All Manuals Search And Download.
CSEFE10xx-10x
Installation -- Continued
Install the Fiber Cable
Operation
Status LEDs
Use the status LEDs to monitor the CSEFE10xx-10x media
converter operation in the network.
PWR
The CSEFE10xx-10x is designed to be installed in pairs over the fiber link,
where one is the local media converter and the other is the remote.
ACT 100 10
F
1. Locate or build fiber-optic cable with male, two-stranded TX to RX
connectors installed at both ends.
TP
TX
PWR
Power
On = Connection to the external AC
or DC power.
2. Connect the fiber cables to the local CSEFE10xx-10x media converter as
described:
F-ACT Fiber Activity
Blinking = Data reception on the fiber
link.
•
•
Connect the male TX cable connector the female TX port.
Connect the male RX cable connector to the female RX port.
F-100 Fiber Speed
On = Fiber link at 100 Mb/s.
3. Connect the fiber cables to the remote CSEFE10xx-10x media converter
as described:
F-10
Fiber Speed
On = Fiber link at 10 Mb/s.
•
•
Connect the male TX cable connector the female RX port.
Connect the male RX cable connector to the female TX port.
TP-ACT Copper Activity Blinking = Data reception on the
twisted-pair copper link.
Connect the fiber cable
to the remote media
converter as shown
Connect the fiber cable
to the local media
converter as shown.
TP-100 Copper Speed On = Copper link at 100 Mb/s.
CSEFE100
TP-10 Copper Speed On = Copper link at 10 Mb/s.
RX
TX
RX
TX
AutoCross™
The AutoCross feature allows either straight-through (MDI) or crossover (MDI-X)
cables to be used when connecting to devices, such as hubs, transceivers, or
network interface cards (NICs). AutoCross determines the characteristics of the
cable connection and automatically configures the unit to link up, regardless of
the cable configuration.
Install the Copper Cable
NOTE: The MDI (straight-through) or MDI-X (crossover) cable connection is
configured automatically, according to the network conditions.
NOTE: The CSEFE10xx-10x series media converter does NOT support rate
conversion between 10Mb/s and 100Mb/s network devices.
1. Locate or build 10/100Base-TX copper cables with male, RJ-45
connectors installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on
the CSEFE10xx-10x media converter.
3. Connect the RJ-45 connector at the other end of the cable to the RJ-45
port on the other device (switch, workstation, etc.).
RJ-45 port
on the media
converter
RJ-45 port
on the other device
(switch, work station, etc.)
4
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CSEFE10xx-10x
Operation -- Continued
SNMP
Cable Specifications
The physical characteristics must meet or exceed IEEE 802.3™ specifications.
Fiber Cable
Use SNMP at an attached terminal or at a remote location to monitor the
media converter by monitoring:
-9
Bit Error Rate:
Single mode:
<10
•
•
•
•
•
•
•
Media converter power
Copper link status
Fiber link status
Copper receive status
Fiber receive status
Link Pass-Through status
Media converter speed
9 µm
CSEFE1012-100
1310 nm single mode
Fiber-optic Transmitter Power:
Fiber-optic Receiver Sensitivity:
Link Budget:
min: -15.0 dBm max: -8.0 dBm
min: -32.0 dBm max: -5.0 dBm
17.0 dB
CSEFE1014-100
1310 nm single mode
Fiber-optic Transmitter Power:
Fiber-optic Receiver Sensitivity:
Link Budget:
min: -15.0 dBm max: -8.0 dBm
min: -32.0 dBm max: -5.0 dBm
17.0 dB
Also, use SNMP to enter network commands that:
•
•
•
Enable/disable Link Pass-Through
Set the speed to 100 Mb/s or 10 Mb/s
Power down the media converter
CSEFE1015-100
1310 nm single mode
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
min: -8.0 dBm
max: -2.0 dBm
See the on-line documentation that comes with Transition Networks
FocalPoint™ software for applicable commands and usage.
min: -34.0 dBm max: -5.0 dBm
26.0 dB
CSEFE1022-100
1310 nm single mode
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
min: -8.0 dBm
max: -2.0 dBm
Cable Specifications
min: -34.0 dBm max: -5.0 dBm
26.0 dB
Copper Cable
CSEFE1029-100
1310 nm (TX)/1550 nm (RX) simplex
min: -14.0 dBm max: -8.0 dBm
min: -33.0 dBm max: -3.0 dBm
19.0 dB
Category 3: (Minimum requirement for 10 Mb/s operation)
Fiber-optic Transmitter Power:
Fiber-optic Receiver Sensitivity:
Link Budget:
Gauge
Attenuation
24 to 22 AWG
11.5 dB/100m @ 5-10 MHz
Category 5: (Minimum requirement for 100 Mb/s operation)
Gauge
Attenuation
24 to 22 AWG
22.0 dB /100m @ 100 MHz
CSEFE1029-101
1550 nm (TX)/1310 nm (RX) simplex
min: -14.0 dBm max: -8.0 dBm
min: -33.0 dBm max: -3.0 dBm
19.0 dB
Fiber-optic Transmitter Power:
Fiber-optic Receiver Sensitivity:
Link Budget:
• Straight-through or crossover copper cable may be used.
• Shielded (STP) or unshielded (UTP) twisted-pair cable may be used.
• Pins 1&2 and 3&6 are the two active pairs in an Ethernet network .
• RJ-45 Pin-out: Pin 1 = TD+, Pin 2 = TD-, Pin 3 = RD+, Pin 6 = RD-
• Use only dedicated wire pairs for the active pins:
(e.g., blue/white & white/blue, orange/white & white/orange, etc.)
• Do not use flat or silver satin wire.
The fiber optic transmitters on this device meet Class I Laser safety
requirements per IEC-825/CDRH standards and comply with 21
CFR1040.10 and 21CFR1040.11.
Straight-Through Cable
Crossover Cable
1
2
1
2
1
2
1
2
Twisted Pair #1
Twisted Pair #2
Twisted Pair #1
Twisted Pair #2
3
6
3
6
3
6
3
6
6
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CSEFE10xx-10x
Technical Specifications
Troubleshooting
For use with Transition Networks Model CSEFE10xx-10x or equivalent.
1.
2.
3.
Is the PWR LED on the media converter illuminated?
Standards:
IEEE 802.3™, 10Base-T, 100Base-TX, 100Base-FX
10 Mb/s, 100 Mb/s
NO
•
•
Data Rate:
Is the media converter inserted properly into the chassis?
Is the power cord properly installed in the chassis and in the
grounded AC outlet?
Dimensions:
Weight:
3.4" x 0.87" x 5" (86 mm x 22 mm x 182 mm)
3 oz (91 g) (approximate)
•
•
Does the grounded AC outlet provide power?
Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
Power Consumption:
Environment:
3.6 watts
YES
•
Tmra*: 0° to 50°C (32° to 122°F)
Storage Temperature: -20° to 85°C (-4° to 185°F)
Humidity: 5 to 95%, non condensing
Altitude: 0 to 10,000 feet
Go to step 2.
Is the F-ACT LED illuminated?
NO
Warranty:
Lifetime
•
•
Check the fiber cables for proper connection.
Verify that the TX and RX cables on the media converter are
connected to the RX and TX ports, respectively, on the other media
converter.
*Manufacturer’s rated ambient temperature: Tmra range for this slide-in-module
depends on the physical characteristics and the installation configuration of the
Transition Networks PointSystem™ chassis in which this slide-in-module will be
installed.
•
Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
•
Go to step 3.
NOTE: The information in this user’s guide is subject to change. For the most
up-to-date information on the CSEFE10xx-10x media converter, view the user’s
Is the F-ACT LED blinking?
NO
•
•
If there is no activity on the fiber port, go to step 4.
If there is activity on the fiber port, disconnect and reconnect the
fiber cable to restart the initialization process.
Restart the workstation to restart the initialization process.
Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
The stand alone version of the media converter is the SSEFE10xx-10x model. For
more information, see the SSEFE10xx-10x user’s guide on-line at:
•
•
YES
Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
•
Go to step 4.
4.
5.
Are the F-100 and/or the TP-100 LEDs illuminated?
YES
CAUTION: Visible and invisible laser radiation when open. Do not stare into
beam or view directly with optical instruments.
•
The media converter is set to 100Mb/s for both the copper fiber links.
If this is not the correct speed, carefully remove the media converter
from the chassis and set switch 1 to “down” (speed = 10 Mb/s).
Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
CAUTION: Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
•
NO
•
Go to step 5.
Are the F-10 and/or the TP-10 LEDs illuminated?
YES
•
The media converter is set to 10 Mb/s for the copper and fiber links.
If this is not the correct speed, carefully remove the media converter
from the chassis and set switch 2 to “up” (speed = 100 Mb/s).
Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
•
NO
•
Go to step 6.
8
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CSEFE10xx-10x
Contact Us
Troubleshooting -- Continued
Technical Support
Technical support is available 24 hours a day.
US and Canada:
International:
6.
Is the TP-ACT LED illuminated?
NO
1-800-260-1312
00-1-952-941-7600
•
Check the twisted-pair copper cables for proper connection.
Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
•
YES
•
Transition Now
Go to step 7.
Chat live via the Web with Transition Networks Technical Support.
7.
Is the TP-ACT LED blinking?
NO
Web-Based Seminars
Transition Networks provides seminars via live web-based training.
•
If there is activity on the copper port, disconnect and reconnect the
copper cable to restart the initialization process.
•
•
Restart the workstation to restart the initialization process.
Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff.
Address
Transition Networks
6475 City West Parkway
Minneapolis, MN 55344, USA
telephone:
toll free:
fax:
952-941-7600
800-526-9267
952-941-2322
Declaration of Conformity
Name of Mfg:
Transition Networks
6475 City West Parkway, Minneapolis MN 55344 USA
Model:
CSEFE10xx-10x Series Media Converters
Part Number(s):
CSEFE1012-100, CSEFE1014-100, CSEFE1015-100,
CSEFE1022-100, CSEFE1029-100, CSEFE1029-101
Regulation:
EMC Directive 89/336/EEC
Purpose: To declare that the CSEFE10xx-10x to which this declaration refers is in
conformity with the following standards.
CISPR 22: 1993; EN55022:1998 Class A ; FCCPart 15 Subpart B; EN 55024:1998;
EN 61000-3-2: 1995; EN 61000-3-3:1995; 21 CFR Subpart J
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
_December 6, 2004_____
Stephen Anderson, Vice-President of Engineering
Date
10
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance Information
CISPR22/EN55022 Class A + EN55024
CE Mark
FCC Regulations
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to correct the
interference at the user's own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus
set out on the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des Communications du Canada.
European Regulations
Warning This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können
bei Betrieb dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für
Gegenmaßnahmen verantwortlich.
Attention! Ceci est un produit de Classe A. Dans un environment domestique, ce produit
risque de créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de
prende les measures spécifiques appropriées.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-
Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der
Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über
Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer
Konformität.
Trademark Notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright Restrictions
© 2005 Transition Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any
means - graphic, electronic, or mechanical - without written permission from Transition
Networks.
Printed in the U.S.A.
33317.A
Download from Www.Somanuals.com. All Manuals Search And Download.
|