Toshiba TV DVD Combo MD13P3 User Manual

Introduction

Connections

Basic setup

DIGITAL VIDEO

COMBINATION COLOR

TELEVISION AND DVD

VIDEO PLAYER

TV operation

Basic playback

MD13P3

OWNER’S MANUAL

Advanced playback

Function setup

Others

Before operating the unit, please read this manual thoroughly.

5K30501B [E] (Cover)

20/4/04, 15:31

Download from Www.Somanuals.com. All Manuals Search And Download.

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5. CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning the exterior cabinet only.

6. ATTACHMENTS

The manufacturer of this unit does not make any recommendations for attachments, as they may cause

hazards.

7. WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet

basement, or near a swimming pool.

PORTABLE CART WARNING

(symbol provided by RETAC)

8. ACCESSORIES

Do not place this unit on an unstable cart, stand, tripod, bracket, or table.

The unit may fall, causing serious injury, and serious damage to the unit.

8A. An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart

combination to overturn.

9. VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation,

and to ensure reliable operation of the unit, and to protect it from overheating.

S3126A

These openings must not be blocked or covered. The openings should never be blocked by placing the unit

on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat

source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper

ventilation is provided or the manufacturer’s instructions have been adhered to.

10. POWER SOURCE

This unit should be operated only from the type of power source indicated on the rating plate. If you are not

sure of the type of power supply to your home, consult your appliance dealer or local power company. For

units intended to operate from battery power, or other sources, refer to the respective pages on this Owner's

Manual for their operating instructions.

11. GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the

other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert

the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to

replace your obsolete outlet. Instead of the polarized alternating-current line plug, your unit may be equipped

with a 3-wire grounding-type plug (a plug having a third (grounding) pin). This plug will only fit into a ground-

ing-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact

your electrician to replace your obsolete outlet.

Do not defeat the safety purpose of the grounding-type plug.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed

upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point

where they exit from the appliance.

5K30501B [E] (P02-05)

20/4/04, 15:31

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

IMPORTANT SAFEGUARDS

(Continued)

13. LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the

unit due to lightning and power line surges.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an

outside antenna system, extreme care should be taken to keep from touching such power lines or circuits,

as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short

out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is

grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the

National Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the

mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for

the grounding electrode.

18. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified service personnel.

For example:

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the operating instructions. Adjust only those

controls that are covered by the operating instructions, as an improper adjustment of other controls

may result in damage and will often require extensive work by a qualified technician to restore the

unit to its normal operation.

e. If the unit has been dropped or the cabinet has been damaged.

f. When the unit exhibits a distinct change in performance, this indicates a need for service.

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by

the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to

determine that the unit is in proper operating condition.

21. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

22. DISC TRAY

Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.

23. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from

the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's

manual of the other equipment carefully and follow the instructions when making any connections.

24. SOUND VOLUME

Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume

sound may cause hearing or speaker damage.

25. SOUND DISTORTION

Do not allow the product output distorted sound for a longtime. It may cause speaker overheating and fire.

26. HEADPHONES

When you use the headphones, keep the volume at a moderate level. If you use the headphones continu-

ously with high volume sound, it may cause hearing damage.

5K30501B [E] (P02-05)

20/4/04, 15:31

Download from Www.Somanuals.com. All Manuals Search And Download.

27. LASER BEAM

Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the

laser beam. It may cause sight damage.

28. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious

personal injury and product malfunction.

29. NOTE TO CABLE TV SYSTEM INSTALLER

This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-

nected to the grounding system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

ANTENNA LEAD

IN WIRE

GROUND

CLAMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

ELECTRIC SERVICE

EQUIPMENT

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC-NATIONAL ELECTRICAL CODE

S2898A

IMPORTANT RECYCLING INFORMATION

This product uses both Cathode Ray Tube (CRT) and other components that contain lead.

In your community there might be regulations that require you to dispose these materials

properly under environmental considerations. Please contact your local authorities, or the

Electronic Industries Alliance (http://www.eiae.org) for disposal or recycling information.

Power source

TO USE AC POWER SOURCE

AC Outlet

Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug

into a standard 120V 60Hz polarized AC outlet.

Wider Hole

and Blade

Notes:

Never connect the AC line cord plug to other than the specified voltage (120V

60Hz). Use the attached power cord only.

•

If the polarized AC cord does not fit into a non-polarized AC outlet, do not attempt to

file or cut the blade. It is the user’s responsibility to have an electrician replace the

obsolete outlet.

•

If you cause a static discharge when touching the unit and the unit fails to function,

simply unplug the unit from the AC outlet and plug it back in. The unit should return

to normal operation.

If the AC cord plug is plugged in for the first time, wait for approx. 5 seconds before

pressing the POWER button.

•

Polarized AC Cord Plug

(One blade is wider than the other.)

5K30501B [E] (P02-05)

20/4/04, 15:31

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Precautions

Notes on handling

Notes on moisture condensation

3 When shipping the unit, the original shipping carton

and packing materials come in handy. For maximum

protection, repack the unit as it was originally packed

at the factory.

3 Do not use volatile liquids, such as insect spray, near

the unit. Do not leave rubber or plastic products to

contact the unit for prolonged period. They will leave

marks on the finish.

Moisture condensation damages the unit. Please

read the following carefully.

Moisture condensation occurs, for example, when you

pour a cold drink into a glass on a warm day. Drops of

water form on the outside of the glass. In the same way,

moisture may condense on the optical pick-up lens

inside this unit, one of the most crucial internal parts of

the unit.

3 The top and rear panels of the unit may become

warm after a long period of use. This is not a

malfunction.

3 When the unit is not in use, be sure to remove the

disc and turn off the power.

3 If you do not use the unit for a long period, the unit

may not function properly in the future. Turn on and

use the unit occasionally.

3 Moisture condensation occurs during the

following cases.

Notes on locating

When you bring the unit directly from a cold place to

a warm place.

3 Place the unit on a level surface. Do not use it on a

shaky or unstable surface such as a wobbling table or

inclined stand. The loaded disc may become dis-

aligned and damage the unit.

3 When you place this unit near a TV, radio, or VCR,

the playback picture may become poor and the sound

may be distorted. In this case, place the unit away

from the TV, radio, or VCR.

When you use the unit in a room where you just

turned on the heater, or a place where the cold wind

from the air conditioner directly hits the unit.

In summer, when you use the unit in a hot and humid

place just after you move the unit from an air

conditioned room.

When you use the unit in a humid place.

Notes on cleaning

Use a soft, dry cloth for cleaning.

For stubborn dirt, soak the cloth in a weak detergent

solution, wring well and wipe. Use a dry cloth to wipe

it dry.

Do not use any type of solvent, such as thinner and

benzine, as they may damage the surface of the unit.

If you use a chemical saturated cloth to clean the unit,

follow that product’s instructions.

3 Do not use the unit when moisture condensation

may occur.

If you use the unit in such a situation, it may damage

discs and internal parts. Remove the disc, connect

the power cord of the unit to the wall outlet, turn on

the unit, and leave it for two or three hours. After two

or three hours, the unit will have warmed up and

evaporated any moisture. Keep the unit connected to

the wall outlet and moisture condensation will seldom

occur.

To obtain a clear picture

The unit is a high technology, precision device. If the

optical pick-up lens and disc drive parts are dirty or worn

down, the picture quality will deteriorate. To obtain a

clear picture, we recommend regular inspection and

maintenance (cleaning or parts replacement) every

1,000 hours of use depending on the operating

environment. For details, contact your nearest dealer.

Wall outlet

5K30501B [E] (P06-07)

20/4/04, 15:31

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes on discs

On handling discs

Structure of disc contents

Do not touch the playback side of the disc.

Normally, DVD video discs are divided into titles, and

the titles are sub-divided into chapters. Video CDs and

Audio CDs are divided into tracks.

DVD video disc

Title 1

Title 2

Chapter 1 Chapter 2

Chapter 1 Chapter 2 Chapter 3

Playback side

Do not attach paper or tape to discs.

Video CD/Audio CD

Track 1

Track 2

Track 3

Track 4

Track 5

On cleaning discs

Fingerprints and dust on the disc cause picture and

sound deterioration. Wipe the disc from the center

outwards with a soft cloth. Always keep the disc

clean.

Each title, chapter or track is assigned a number, which

is called “title number”, “chapter number” or “track

number” respectively.

There may be discs that do not have these numbers.

Notes on copyright

It is forbidden by law to copy, broadcast, show,

broadcast on cable, play in public, and rent copyrighted

material without permission.

If you cannot wipe off the dust with a soft cloth, wipe

the disc lightly with a slightly moistened soft cloth and

finish with a dry cloth.

DVD video discs are copy protected, and any

Do not use any type of solvent such as thinner,

benzine, commercially available cleaners or antistatic

spray for vinyl LPs. It may damage the disc.

recordings made from these discs will be distorted.

This product incorporates copyright protection

technology that is protected by method claims of certain

U.S. patents and other intellectual property rights

owned by Macrovision Corporation and other rights

owners. Use of this copyright protection technology

must be authorized by Macrovision Corporation, and is

intended for home and other limited viewing uses only

unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is

prohibited.

On storing discs

Do not store discs in a place subject to direct sunlight

or near heat sources.

Do not store discs in places subject to moisture and

dust such as a bathroom or near a humidifier.

Store discs vertically in a case. Stacking or placing

objects on discs outside of their case may cause

warping.

5K30501B [E] (P06-07)

20/4/04, 15:31

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Notes on discs (Continued)

About this owner’s manual

Playable discs

This owner’s manual explains the basic instructions of

this unit. Some DVD video discs are produced in a

manner that allows specific or limited operation during

playback. As such, the unit may not respond to all

operating commands. This is not a defect in the unit.

Refer to instruction notes of discs.

This unit can play the following discs.

Maximum

playback time

Disc

Disc Mark Contents

Size

Approx. 4 hours

(single sided disc)

12 cm

Audio

Video

(moving

pictures)

“

” may appear on the TV screen during operation.

Approx. 8 hours

(double sided disc)

A “ ” means that the operation is not permitted by the

unit or the disc.

For example, sometimes it is unable to stop the

playback of copyright message of the disc when the

STOP (3) button is pressed. Alternatively, the “ ” may

also indicate that the feature is not available for the disc.

DVD

video

discs

Approx. 80 minutes

(single sided disc)

8 cm

Approx. 160 minutes

(double sided disc)

Notes on region numbers

Approx. 74 minutes

Approx. 20 minutes

12 cm

Audio

Video

(moving

pictures)

The region number of this unit is 1. If region numbers,

which stand for their playable area, are printed on your

Video

CDs

ALL

DVD video disc and you do not find

, disc

DIGITAL VIDEO

8 cm

playback will not be allowed by the player. (In this case,

the unit will display a message on-screen.)

Approx. 74 minutes

Approx. 20 minutes

12 cm

On Video CDs

Audio

CDs

Audio

This DVD supports Video CDs equipped with the PBC

(Version 2.0) function. (PBC is the abbreviation of

Playback Control.) You can enjoy two playback

variations depending on types of discs.

8 cm

(CD

single)

The following discs are also available.

CD-R/CD-RW discs of CD-DA or Video CD format

Some of these discs may be incompatible.

• Video CD not equipped with PBC function

(Version 1.1)

Sound and movie can be played on this DVD in the

same way as an audio CD.

• You cannot play discs other than those listed above.

• You cannot play discs of DVD-RAM, DVD-ROM,

Photo CD, etc., or non standardized discs even if they

may be labeled as above.

• Some CD-R/RWs can not be played back depending

on the recording conditions.

• This unit uses the NTSC color system, and cannot

play DVD video discs recorded in any other color

system (PAL, SECAM, etc.).

• Video CD equipped with PBC function

(Version 2.0)

In addition to operation of a Video CD not equipped

with the PBC function, you can enjoy playback of

interactive software with search function by using the

menu displayed on the TV screen (Menu Playback).

Some of the functions described in this owner’s

manual may not work with some discs.

5K30501B [E] (P08-12)

20/4/04, 15:31

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Advanced playback

Introduction

Zooming ......................................................... 31

Locating desired scene .................................. 31

Repeat playback ............................................ 32

A-B Repeat playback ..................................... 32

Program playback .......................................... 33

Random playback .......................................... 33

Changing angles ............................................ 34

Title selection ................................................. 34

DVD menu...................................................... 34

Changing soundtrack language ..................... 35

Subtitles ......................................................... 35

Karaoke playback........................................... 36

Disc status...................................................... 36

To turn off the PBC ........................................ 36

IMPORTANT SAFEGUARDS............................2

Precautions .......................................................6

Notes on discs...................................................7

Contents ............................................................9

Identification of controls ..................................10

Connections

Antenna connections.......................................13

Cable TV connections .....................................14

Connecting to optional equipment...................15

Basic setup

Starting setup ..................................................18

Setting the language .......................................19

Function setup

TV operation

Customizing the function settings .................. 37

Temporary disabling of rating level

by DVD disc ................................................... 40

TV operation....................................................20

Closed captions...............................................22

To memorize channels ....................................23

Setting the V-Chip ...........................................24

Picture control adjustment...............................26

Adjusting the picture preference .....................26

Stereo and Second Audio Program (SAP) ......27

Others

Language code list ......................................... 41

Problems and troubleshooting ....................... 42

Reception disturbances.................................. 44

Specifications ................................................. 45

LIMITED WARRANTY ................................... 46

Basic playback

Playing a disc ..................................................28

5K30501B [E] (P08-12)

20/4/04, 15:31

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Identification of controls

See the page in

for details.

Front

POWER indicator 20

Disc tray

AUDIO (L/R)/VIDEO IN jacks (LINE)

POWER button 18

STOP( ) button

PHONES jack 21

SKIP (

) buttons 30

Remote sensor

PLAY ( ) button 28

CHANNEL ( / ) buttons

OPEN/CLOSE ( ) button

VOLUME ( / ) buttons 20

Rear

COAXIAL DIGITAL AUDIO OUT jack

RF IN jack

AC power cord

5K30501B [E] (P08-12)

20/4/04, 15:31

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control

The instructions in this manual describe the function on the remote control. See the page in

for details.

RECALL

TV/DVD

POWER

INPUT SELECT

GAME

OPEN/CLOSE

MUTE

SLEEP

CLOSED

CAPTION

TOP MENU

SUBTITLE

AUDIO

ANGLE

SETUP/MENU DVD MENU

CANCEL ZOOM/CH RTN

CH +

VOL –

VOL +

RETURN

ENTER

CH –

REV

PLAY

STOP

FWD

SKIP

PLAY MODE

JUMP

SKIP

SLOW

PAUSE

SLOW

REPEAT A–B

*DVD MENU button

Use the DVD MENU button to

display the menu included on

many DVD video discs.

To operate a menu, follow the

instructions in “DVD menu.”

5K30501B [E] (P08-12)

20/4/04, 15:31

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Inserting batteries

Slide the battery compartment

cover in the direction of the

arrow.

Install two “AAA” batteries

(supplied), paying attention to

the polarity diagram in the

battery compartment.

Replace the compartment

cover.

Operation

• Aim the remote control at the remote sensor and press control buttons to operate.

• Operate the remote control within 30° angle on either side of the remote sensor, up to a distance of approx. 5

meters.

Approx. 5 meters

The precautions below should be followed when using batteries in this device:

1. Use only the size and type of batteries specified.

2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.

Reversed batteries may cause damage to the device.

3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from

possible battery leakage.

5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture (follow battery

manufacturer’s directions).

5K30501B [E] (P08-12)

20/4/04, 15:31

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Antenna connections

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If

you are using a cable TV service (CABLE), see page 14 for Cable TV connections.

Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)

Connect the 75 ohm cable from the combination

VHF/UHF antenna to the antenna jack.

Antenna

jack

Antenna

jack

If your combination VHF/UHF antenna has a 300

ohm twin-lead wire, the use of the 300-75 ohm

matching transformer may be necessary.

75 ohm coaxial cable

(not supplied)

300-75 ohm matching

transformer (supplied)

Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)

Connect the UHF 300 ohm twin-lead wire to the

Antenna

300-75 ohm matching

transformer (supplied)

combiner (not supplied). Connect the VHF 300

ohm twin-lead wire to the 300-75 ohm matching

transformer.Attachthetransformertothecombiner,

then attach the combiner to the antenna jack.

jack

Combiner

(not supplied)

UHF 300 ohm

twin-lead wire

(not supplied)

VHF 300 ohm

twin-lead wire

(not supplied)

Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)

Connect the VHF 75 ohm cable and UHF 300 ohm

twin-lead wire to the combiner (not supplied).

Attach the combiner to the antenna jack.

Antenna

jack

VHF 75 ohm

(not supplied)

Combiner

(not supplied)

UHF 300 ohm

twin-lead wire

(not supplied)

5K30501B [E] (P13-23)

20/4/04, 15:31

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Cable TV connections

This TV/DVD has an extended tuning range and can tune most cable channels without using a Cable TV converter box.

Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for

normal viewing requires the use of a descrambler device which is generally provided by the cable company.

For subscribers to basic cable TV service

Antenna

jack

For basic cable service not requiring a converter/descrambler

box, connect the Cable TV 75 ohm coaxial cable directly to the

Antenna jack on the back of the TV/DVD.

75 ohm

coaxial cable

For subscribers to scrambled cable TV service

If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the

incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect

the output jack of the converter/descrambler box to the antenna jack on the TV/DVD. Follow the connections

shown below. Set the TV/DVD to the output channel of the converter/descrambler box (usually channel 3 or 4)

and use the converter/descrambler box to select channels.

Incoming

75 ohm

Cable TV

Antenna

jack

75 ohm cable to

TV/DVD

Converter/

descrambler

For subscribers to unscrambled basic cable TV service with scrambled

premium channels

If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the

use of a converter/descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the

cable company or an electronics supply store). Follow the connections shown below. With the switch in the “B”

position, you can directly tune any nonscrambled channels on your TV/DVD. With the switch in the “A” position, tune

your TV/DVD to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/

descrambler box to tune scrambled channels.

Converter/

descrambler

Incoming

75 ohm

Antenna

jack

75 ohm cable

to TV/DVD

Cable TV

A/B switch

Splitter

5K30501B [E] (P13-23)

20/4/04, 15:32

Download from Www.Somanuals.com. All Manuals Search And Download.

INPUT SELECT

GAME

Connecting to optional equipment

You can enjoy VCR, camcorder or TV game with connection to external

input. To select the external input, press INPUT SELECT and select “LINE”

mode.

To connect the TV/DVD to a VCR

Press the INPUT SELECT to select the “LINE” (external input) to use the TV as a monitor.

Operate your VCR as usual.

VCR

: Signal flow

Front of TV/DVD

VIDEO IN

AUDIO IN (R)

AUDIO IN (L)

To Audio/Video OUT

Audio/Video cable (not supplied)

To connect the TV/DVD to a camcorder

To playback from the camcorder, connect the camcorder to the TV/DVD as shown.

Camcorder

Front of TV/DVD

: Signal flow

VIDEO IN

AUDIO IN (R)

AUDIO IN (L)

To Audio/Video OUT

Audio/Video cable (not supplied)

To connect the TV/DVD to a TV Game

You can enjoy playing a TV game on the screen by adjusting to suitable brightness for your eyes.

1. Connect a TV Game to the TV/DVD.

2. Press GAME. The GAME mode screen appears.

• This TV/DVD has the GAME mode function (see page 21).

: Signal flow

Front of TV/DVD

VIDEO IN

AUDIO IN (R)

To Audio/Video OUT

AUDIO IN (L)

Audio/Video cable (not supplied)

Notes:

• You can also change the TV screen to LINE by pressing the CH +/– buttons.

• The TV/DVD can also be used as a display device for many video games. However, due to the wide variety of different

types of signal generated by these devices and subsequent hook-up variations required, they have not all been included

in the suggested connection diagrams. You'll need to consult each component's Owner's Manual for additional

information.

5K30501B [E] (P13-23)

20/4/04, 15:32

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Connecting to optional equipment (Continued)

You can enjoy high quality dynamic sounds by connecting the TV/DVD to optional audio equipment.

: Front speaker

: Rear speaker

: Sub woofer

: Center speaker

: Signal flow

Connecting to an amplifier equipped with a Dolby Digital decoder

Dolby Digital

Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to

reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs with this dynamic

realistic sound by connecting the TV/DVD to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital

processor. If you have a Dolby Surround Pro Logic decoder, you will obtain the full benefit of Pro Logic from the same DVD

movies that provide full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark.

Amplifier equipped with a

Dolby Digital decoder

Manufactured under license

from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the

double-D symbol are trade-

marks of Dolby Laboratories.

To COAXIAL

type digital

audio input

75 Ω coaxial cable (not supplied)

Connecting to an amplifier equipped with Dolby Surround Pro Logic

Dolby Surround Pro Logic

You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right

and left front speakers, a center speaker, and one or two rear speakers).

3 With an amplifier equipped with Dolby Digital

Connect the equipment the same way as described in “Connecting to an amplifier equipped with a Dolby Digital decoder.”

Refer to that amplifier’s owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.

3 With an amplifier not equipped with Dolby Digital

Connect the equipment as follows.

Amplifier equipped with

Dolby Surround Pro Logic

Connect one or two rear speak-

ers. The output sound from the

rear speakers will be monaural

even if you connect two rear

speakers.

To COAXIAL

type digital

audio input

75 Ω coaxial cable (not supplied)

Connecting to an amplifier equipped with a DTS decoder

Digital Theater Systems (DTS)

DTS is a high quality surround technology used in theaters and now available for home use, on DVD video discs or audio CDs.

If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS encoded sound tracks on DVD

video discs or audio CDs.

Amplifier equipped with a

DTS decoder

To COAXIAL

type digital

audio input

“DTS” and “DTS Digital

Surround” are trademarks of

Digital Theater Systems, Inc.

75 Ω coaxial cable (not supplied)

5K30501B [E] (P13-23)

20/4/04, 15:32

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting to an amplifier equipped with a MPEG audio decoder

MPEG2 sound

You can enjoy motion picture and live concert DVD video discs with dynamic realistic sound by connecting an amplifier

equipped with an MPEG2 audio decoder or MPEG2 audio processor.

Amplifier equipped with an

MPEG2 audio decoder

To COAXIAL

type digital

audio input

75 Ω coaxial cable (not supplied)

Connecting to an amplifier equipped with a digital audio input

2 channel digital stereo

You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input

and speaker system (right and left front speakers).

Amplifier equipped with a

Digital audio input

To COAXIAL

type digital

audio input

75 Ω coaxial cable (not supplied)

Notes:

• DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD to the AC-3 RF input of a Dolby Digital Receiver.

This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL AUDIO

OUT jack of the TV/DVD.

• Connect the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD to the “COAXIAL” input of a Receiver or Processor.

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the TV/DVD to other equipment, be sure to turn off the power and unplug all of the equipment from the

wall outlet before making any connections.

• The output sound of the TV/DVD has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate

listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the TV/DVD’s power cord. If you leave the amplifier power on, the

speakers may be damaged.

5K30501B [E] (P13-23)

20/4/04, 15:32

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic setup

POWER

Starting setup

The STARTING SETUP function makes installing your TV/DVD easily. It leads

you the Language selection, TV/CABLE selection and auto channel memory

automatically.

CANCEL

IMPORTANT: Make sure that the antenna or cable TV system connection

is made!

ENTER

Starting setup

Now the “AUTO CH MEMORY” starts.

Press POWER.

After the starting setup is completed, the TV

channel appears on the screen.

The starting setup function begins and the

Language setup menu appears on the screen.

Press

to select your desired

language, then press ENTER.

Note:

If you press the CANCEL button in the process of

“AUTO CH MEMORY” you can do starting set up

function again.

POWER

ENTER

LANGUAGE/IDIOMA/LANGUE

ENGLISH

ESPAÑOL

FRANCAIS

CH +

CH –

AUTO CH MEMORY

STOP : CANCEL

^{/ ENTER}>

Press

to select “TV” or “CABLE”, then

press ENTER.

ENTER

Note:

CH +

CH –

CHANNEL PLAN

The starting setup function will work only when you press the

POWER button for the first time.

CABLE

^{/ ENTER}>

Press

to select “START”, then press

ENTER.

If you select “CANCEL” and press ENTER, the

STARTING SETUP stops and changes to the TV

screen.

ENTER

CH +

AUTO SETUP

START

CANCEL

CH –

^{/ ENTER}>

5K30501B [E] (P13-23)

20/4/04, 15:32

Download from Www.Somanuals.com. All Manuals Search And Download.

POWER

Setting the language

This TV/DVD can display the on screen language in English, Spanish or French.

Select the language you prefer first, then proceed with the other menu

options.

ENTER

Setting the language

Press MENU, then press

option.

to select

SETUP/MENU

LANGUAGE/IDIOMA/LANGUE

VOL –

VOL +

ENGLISH

ESPAÑOL

FRANCAIS

/MENU

Press

to select the desired language:

English (ENGLISH), Spanish (ESPAÑOL) or

French (FRANCAIS), then press ENTER.

ENTER

CH +

LANGUAGE/IDIOMA/LANGUE

ENGLISH

ESPAÑOL

CH –

FRANCAIS

/ ENTER/MENU

Press MENU repeatedly until the menu screen

is cleared.

SETUP/MENU

Notes:

• If the unit does not operate properly, or No key operation

(by the unit and/or the remote control): Static electricity,

etc., may affect the player's operation. Disconnect the AC

power cord once, then connect it again.

• The TV section has its own menu and also DVD section has

its own menu (see page 37).

5K30501B [E] (P13-23)

20/4/04, 15:32

Download from Www.Somanuals.com. All Manuals Search And Download.

TV operation

POWER

0–9

TV operation

VOL +/–

TV operation

To turn on the TV/DVD, press POWER.

The Power indicator will light.

Press direct channel selection (0–9) to select

the channel.

POWER

TV mode direct channel selection

When the TV/CABLE selection is in the TV

position, all channels can be instantly selected by

using two buttons. (for example, to select channel

2, press “0”, then “2”. If

Adjust the volume level by pressing VOL + or –.

The volume level will be indicated on the

screen by green bars. As the volume level

increases, so do the number of bars. If the

volume decreases, the number of green bars

also decreases.

you press only “2”,

channel selection will

CH 12

be delayed for a few

seconds.) For channels

10 and above, press

the 2 digits in order.

CABLE mode direct channel selection

When the TV/CABLE selection is in the CABLE

position, channels can be selected as follows:

TO SELECT CABLE TV CHANNELS:

VOL –

VOL +

1-9:

Press “0” twice, then 1-9 as needed.

Example, to select channel 2, press “002”.

Press “0”, then the remaining 2 digits.

Example, to select channel 12, press “012”.

Press the 2 digits in order. Example, to

select channel 36, press “36”.

VOLUME

10-12:

13-99:

100-125: Press the 3 digits in order. Example, to

select channel 120, press “120”.

NOTE FOR CHANNELS 1-12:

If only 1 or 2 buttons are pressed, the corresponding

channel will be selected in 2 seconds.

Set the TV/CABLE selection to the appropriate

position. (See page 23.)

- VHF/UHF channels

CABLE - Cable TV channels

CATV

VHF

2-13

VHF

2-13

UHF

14-69

STD/HRC/IRC

14-36

(A) (W)

37-59

(AA) (WW)

60-85

(AAA) (ZZZ)

86-94

(86) (94)

95-99

(A-5) (A-1)

100-125

(100) (125)

(5A)

Notes:

• If a channel with no broadcast is selected, the sound will auto-

matically be muted.

• If a station being viewed stops broadcasting, the TV will auto-

matically shut itself off after 15 minutes.

5K30501B [E] (P13-23)

20/4/04, 15:32

Download from Www.Somanuals.com. All Manuals Search And Download.

RECALL

GAME

SLEEP

MUTE

CH RTN

CH +/–

VOL +/–

■ SLEEP

■ CHANNEL UP/DOWN

To set the TV/DVD to turn off after a preset amount of

time, press SLEEP on the remote control. The clock

will count down 10 minutes for each press of SLEEP

(120, 110, ...10, 0). After the sleep time is programmed,

the display will appear briefly every ten minutes to

remind you that the sleep timer is operating. To confirm

the sleep timer setting, press SLEEP and the remain-

ing time will be displayed for a few seconds. To cancel

the sleep timer, press SLEEP repeatedly until the

display turns to 0.

Press and release CH + or –. The channel automati-

cally stops at the next channel set into memory.

For proper operation, before selecting channels, they

should be set into the memory. See page 23 “To

memorize channels”.

CH +

CH –

SLEEP

120

■ RECALL

Press RECALL to display the current informations on the

screen. Press RECALL again to clear the display.

• Channel number or external input mode

• Stereo or SAP (Second Audio Program) audio status

• Audio output status

■ GAME MODE

After connecting a TV Game to the unit, press GAME.

The TV screen changes to the Game mode.

• The Game mode screen is adjusted to the suitable

brightness for your eyes.

STEREO SAP

CH 012

RECALL

• Game timer function: After one hour the Game timer

display will appear every 30 minutes for approx. 5

seconds showing how long the time has passed up

to 4 hours.

SEL. STEREO

• If GAME is pressed during standby mode, the unit

turns on automatically and the Game mode screen

appears on the screen.

■ CH RETURN

This button allows you to go back to the last channel

selected by pressing CH RTN. Press CH RTN again to

return to the last channel you were watching.

ZOOM/CH RTN

■ HEADPHONES

Insert a stereo headphones (not supplied) with a 1/8”

mini plug into the PHONES jack on the front panel. If

you connect headphones, the sound from TV speakers

is muted.

■ MUTE

Press MUTE to switch off the sound. The TV/DVD’s

sound will be silenced and “MUTE” will briefly appear on

the screen. The sound can be switched back on by

pressing this button again or one of VOL + /–.

MUTE

VOL –

VOL +

5K30501B [E] (P13-23)

20/4/04, 15:32

Download from Www.Somanuals.com. All Manuals Search And Download.

TV operation

Closed captions

WHAT IS CLOSED CAPTIONING?

CLOSED

CAPTION

This television has the capability to decode and display closed captioned

television programs. Closed captioning will display text on the screen for

hearing impaired viewers or it will translate and display text in another

language.

Closed captions

Captions: This closed caption mode will display text on the screen in English or another language (depending

on the setting of the closed captions CH 1/2).

Generally, closed captions in English are transmitted on captions channel 1 and closed captions in other lan-

guages are transmitted on captions channel 2.

Text: The text closed caption mode will usually fill the screen with a programming schedule or other information.

After selecting a closed caption mode, it will stay in effect until it is changed, even if the channel is changed.

If the captions signal is lost due to a commercial or a break in the signal, the captions will reappear when the

signal is received again. If the channels are changed, the captions will be delayed approximately 10 seconds.

The captions will appear in places on the screen where they will least interfere with the picture, usually on the

bottom of the screen. News programs will usually show three-line closed captions which scroll onto the screen.

Most other shows provide two or three lined captions placed near the character who is speaking so the viewer

can follow the dialogue. Words in italics or underlined describe titles, words in foreign languages or words

requiring emphasis. Words that are sung usually appear enclosed by musical notes.

For television programs broadcasting with closed captions, look in your TV guide for the closed captions symbol

(CC).

TO VIEW CLOSED CAPTIONS

Press CLOSED CAPTION to switch between normal TV and the two closed

caption modes (captions and full screen text). Closed captioning will display text

on the screen for hearing impaired viewers.

CLOSED

CAPTION

Notes:

• When selecting closed captions, the captioning will be delayed approximately 10 seconds.

• If no caption signal is received, no captions will appear, but the television will remain in the caption mode.

• Misspellings or unusual characters may occasionally appear during closed captioning. This is normal with closed captioning,

especially with live programs. This is because during live programs, captions are also entered live. These transmissions do not

allow time for editing.

• When captions are being displayed, on-screen displays, such as volume and mute may not be seen or may interfere with closed

captions.

• Some cable systems and copy protection systems may interfere with the closed captioned signal.

• If using an indoor antenna or if TV reception is very poor, the closed caption decoder may not appear or may appear with

strange characters or misspelled words. In this case, adjust the antenna for better reception or use an outdoor antenna.

5K30501B [E] (P13-23)

20/4/04, 15:32

Download from Www.Somanuals.com. All Manuals Search And Download.

To memorize channels

0–9

This TV/DVD is equipped with a channel memory feature which allows

channels to skip up or down to the next channel set into memory, skipping over

unwanted channels. Before selecting channels, they must be programmed into

the TV/DVD’s memory. In addition to normal VHF and UHF channels, this TV/

DVD can receive up to 113 Cable TV channels. To use this TV/DVD with an

antenna, set the TV/CABLE selection to the TV position. When shipped from

the factory, this selection is in the CABLE position.

TV/CABLE selection

Automatic memory tuning

Press MENU in the TV mode, then press

Press

to select the “AUTO CH MEMORY”,

to select

SETUP/MENU

option.

then press

The TV will begin memorizing all the channels

available in your area.

CH +

VOL +

CH –

VOL –

VOL +

Press

to select “TV/CABLE”.

CH +

To ADD/DELETE channels

CH –

Press

press

to select “ADD/DELETE”, then

CH +

CH –

Press

to select “TV” or “CABLE”.

VOL +

TV - VHF/UHF channels

CABLE - Cable TV channels

VOL –

VOL +

Select the desired channel to be added or

deleted using Direct channel selection (0–9) or

CH + / –.

CH +

CH –

Press MENU repeatedly until the menu screen is

cleared.

SETUP/MENU

Press

to select “ADD” or “DELETE”,

whichever function you want to perform.

Cable TV chart

The chart below is typical of many cable system channel

allocations.

ADD

CH 001

VOL –

VOL +

0-9 /

5K30501B [E] (P13-23)

20/4/04, 15:32

Download from Www.Somanuals.com. All Manuals Search And Download.

TV operation

Setting the V-Chip

0–9

An age limitation can be set to forbid children to watch programs according to

“TV RATING” and “MOVIE RATING” level set. To use the V-Chip function,

you must register a password.

CANCEL

Notes:

ENTER

• If you forget the password, you cannot set the V-Chip.

• To avoid forgetting the password, write it down and keep in

the safe place.

To register password

To change password

In the V-CHIP menu, press

“CHANGE PASSWORD”, then press

to select

Press MENU, then press

option.

to select

SETUP/MENU

CH +

VOL +

CH –

V-CHIP SET

VOL –

VOL +

NEW

PASSWORD : – – – –

/ MENU

Press

CH +

to select “PASSWORD”.

Enter the new password using Numbered

buttons (0–9), then press ENTER.

ENTER

V-CHIP SET

CH –

NEW

PASSWORD : – – – –

CHANGE PASSWORD

NEW

0–9/ENTER/CANCEL/MENU

PASSWORD

: – – – –

Enter the password (4 digits) using Numbered

buttons (0–9), then press ENTER.

• If you put a wrong number, press CANCEL.

0-9/ENTER/CANCEL/MENU

Enter the same password again using

Numbered buttons (0–9) for safety, then press

ENTER.

V-CHIP SET

ENTER

NEW

CHANGE PASSWORD

PASSWORD

CONFIRM

PASSWORD

0–9/ENTER/CANCEL/MENU

CANCEL

ENTER

0-9/ENTER/CANCEL/MENU

“

” appears instead of the number.

Enter the same password again for the safety,

then press ENTER.

Now the password was registered and V-Chip

setting menu will appear on the display.

Press MENU repeatedly until the menu screen

is cleared.

SETUP/MENU

ENTER

V-CHIP SET

CONFIRM

PASSWORD

0–9/ENTER/CANCEL/MENU

5K30501B [E] (P24-27)

20/4/04, 15:32

Download from Www.Somanuals.com. All Manuals Search And Download.

RECALL

ENTER

To set the V-Chip

Press

to select desired rating.

In the V-CHIP menu, press

to select

After setting, press ENTER.

“V-CHIP SET”, then press

VOL –

VOL +

CH +

V-CHIP SET

TV RATING

MOVIE RATING

TV-Y

PG-13

V-CHIP

V-CHIP SET

CHANGE PASSWORD

OFF

ENTER

VOL +

CH –

/ ENTER/MENU

/ MENU

OFF : MOVIE RATING is not set

: All ages

: Parental guidance

Press

press or

After setting, press ENTER.

to select “TV RATING”, then

to display the desired setting.

PG-13 : Parental guidance

less than 13 years old

OFF : TV RATING is not set

TV-Y : All children

: Under 17 years old

Parental guidance suggested

NC-17 : 17 years old and above

TV-Y7 : 7 years old and above

TV-G : General audience

TV-PG : Parental guidance

TV-14 : 14 years old and above

TV-MA: 17 years old and above

: Adult only

Press

or to select “V-CHIP”.

CH +

CH –

When you select TV-

Y7, TV-PG, TV-14 or

TV-MA, press

RECALL to show the

contained rating.

Press or

V-CHIP

V-CHIP SET

CHANGE PASSWORD

OFF

V-CHIP SET

TV RATING

MOVIE RATING

TV-Y

OFF

/ MENU

to select the desired

item you want.

/ ENTER/MENU

Press

to display “ON”.

Now your settings were set into the memory.

CH +

ENTER

RECALL

VOL –

VOL +

VOL –

VOL +

V-CHIP

V-CHIP SET

CHANGE PASSWORD

CH –

Press

to select “MOVIE RATING”.

/ MENU

Press MENU repeatedly until the menu screen is

cleared.

CH +

CH –

V-CHIP SET

TV-Y

OFF

TV RATING

MOVIE RATING

SETUP/MENU

To use after the TV is protected

When the program applied to the V-Chip setting is received,

/ ENTER/MENU

enter the password, then press ENTER. Protection can be

canceled.

Note:

The V-Chip function is activated only on programs that have

the rating signal.

5K30501B [E] (P24-27)

20/4/04, 15:33

Download from Www.Somanuals.com. All Manuals Search And Download.

TV operation

Picture control adjustment /

Adjusting the picture preference

CANCEL

Picture controls are factory preset but you can adjust them individually as follows:

And also you can select four picture modes—Standard, Sports, Movie, and

Memory—as described in the following table:

ENTER

Picture control adjustment

Adjusting the picture preference

Press MENU, then press

option.

to select

Press MENU, then press

option.

to select

SETUP/MENU

PICTURE

PICTURE PREFERENCE

PICTURE

PICTURE PREFERENCE

VOL –

VOL +

VOL –

VOL +

Press

to select “PICTURE”, then press

/ MENU

Press

to select “PICTURE

PREFERENCE”, then press

PICTURE

PICTURE PREFERENCE

CH +

VOL +

CH +

CH –

PICTURE

PICTURE PREFERENCE

VOL +

/ MENU

CH –

Press

adjust, then press

to select the item you want to

/ MENU

to adjust the setting.

Press

to select the desired picture

mode, then press ENTER.

CH +

BRIGHTNESS

CONTRAST

COLOR

TINT

SHARPNESS

+32

VOL –

VOL +

ENTER

CH –

CH +

PICTURE PREFERENCE

STANDARD

SPORTS

MOVIE

/ CANCEL / MENU

CH –

MEMORY

Selection

Pressing

/ ENTER / MENU

BRIGHTNESS

CONTRAST

COLOR

TINT

SHARPNESS

darker

lower

paler

reddish

softer

lighter

higher

deeper

greenish

sharper

Mode

Picture quality

STANDARD Standard picture quality (factory-set)

SPORTS

MOVIE

Bright and dynamic picture (factory-set)

Movie-like picture setting (factory-set)

Your personal preferences (set by you;

see “Picture control adjustment” as left)

Note:

MEMORY

The CONTRAST default setting is set to maximum

(+32) at the factory.

After your desired setting press MENU

repeatedly until the menu screen is cleared.

After your desired setting press MENU

repeatedly until the menu screen is cleared.

SETUP/MENU

Note:

3 To return all adjustments to the factory preset levels

You can not select “PICTURE PREFERENCE” in the Game

mode.

26 ^{Press CANCEL while making picture adjustments.}

5K30501B [E] (P24-27)

20/4/04, 15:33

Download from Www.Somanuals.com. All Manuals Search And Download.

Stereo and Second Audio Program (SAP)

The TV/DVD is equipped with a feature known as multi-channel TV sound or

MTS. MTS broadcasts greatly enhance TV viewing by bringing you programs

with high fidelity stereo sound.

AUDIO

MTS also provides an extra channel called the Second Audio Program or SAP

which broadcasters can use to transmit a second language for bilingual transmis-

sion or for other purposes.

Listening to stereo sound

To select desired sound

When the TV is turned on or a channel selection is

made, make certain the “STEREO” appears on

the screen. This means that Stereo broadcasting

is available. You can enjoy stereo sound from the

left and right speakers.

Press AUDIO to select the desired sound.

AUDIO

• When mono broadcasting is received, no indication

is displayed.

• If the broadcast signal is not strong enough or clear

stereo sound is not available, press AUDIO to

change to mono sound. The noise should be elimi-

nated. Press it again to return to the stereo sound.

SEL. STEREO

MONO + SAP BROADCASTING

MONO SOUND

SAP SOUND

(MAIN)

STEREO

CH 013

AUDIO

STEREO+SAP BROADCASTING

STEREO SOUND

SAP SOUND

(MAIN)

MONO SOUND

(MAIN)

Listening to SAP (Second Audio Program)

When the TV is turned on or a channel selection is

made, make certain the SAP appears on the screen.

This means that the Second Audio Program

broadcasting is available.

STEREO SAP

CH 013

5K30501B [E] (P24-27)

20/4/04, 15:33

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic playback

Playing a disc

This section shows you the basics on how to play a disc.

CAUTION

Keep your fingers well clear of the disc tray as it is closing.

Neglecting to do so may cause serious personal injury.

1 3,5

DVD

VCD

Basic playback

Preparations:

• Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet. If the AC cord plug is plugged in for the first time,

you need to set “Starting setup” (see page 18).

• When connecting to other equipment, turn power off.

Press OPEN/CLOSE or PLAY.

Press POWER on the unit or on the remote control

to turn on the unit.

The Power indicator will light.

• Every time you press POWER, the TV/DVD starts from

TV mode.

• When using an amplifier, switch on the amplifier.

The disc tray closes automatically.

On the TV-screen, “ ” changes to

“Reading” and then playback

commences.

Reading

Press TV/DVD to select DVD mode.

The DVD startup screen will appear on the screen.

“Reading” display will change to “No Disc”. (If DVD

disc has already loaded, playback will start automati-

cally.)

Reading

• A menu screen will appear on the TV screen, if

the disc has a menu feature.

Press C/D or B/A to select title, then press ENTER.

Title is selected and play commences.

Press STOP to end playback.

Press OPEN/CLOSE.

3Resuming facility

• The unit records the stopped point,

depending on the disc. “

appears on the screen. Press

PLAY to resume playback (from

the scene point).

• If you press STOP again or unload

the disc (“3” appears on the

screen.), the unit will clear the

stopped point.

The disc tray opens.

”

Place the disc on the disc tray.

3 To start playback in the stop mode

Press PLAY.

With the playback

side down

Note:

• There are two different disc sizes. Place the disc in

the correct guide on the disc tray. If the disc is out of

the guide, it may damage the disc and cause the unit

to malfunction.

If the unit does not operate properly:

Static electricity, etc., may affect the player's operation.

Disconnect theAC power cord once, then connect it again.

• Do not place a disc which is unplayable on the disc tray.

5K30501B [E] (P28-32)

20/4/04, 15:33

Download from Www.Somanuals.com. All Manuals Search And Download.

To obtain a higher quality picture

TV/DVD

POWER

Occasionally, some picture noise not usually visible during a normal broadcast

may appear on the TV screen while playing a DVD video disc because the high

resolution pictures on these discs include a lot of information. While the amount of

noise depends on the TV you use with this unit, you should generally reduce the

sharpness adjustment on your TV when viewing DVD video discs.

OPEN/CLOSE

DVD VCD

About

The

DVD VCD

icons on the heading bar show the playable discs for the

function described under that heading.

PLAY

STOP

: You can use this function with DVD video discs.

: You can use this function with Video CDs.

: You can use this function with Audio CDs and CD-R/RW CDs.

VCD

PAUSE

To remove the disc

Press OPEN/CLOSE.

To pause playback (still mode)

Press PAUSE during playback.

PAUSE

Remove the disc after the disc tray

opens completely.

To resume normal playback, press

PLAY.

• The sound is muted during still

mode.

To stop playback

Press STOP.

STOP

Be sure to press OPEN/CLOSE to close the disc tray

after you remove the disc.

Notes:

• If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen

according to the type of loaded disc. In this case, check your disc again (see pages 8 and 39).

• Some discs may take a minute or so to start playback.

• When you set a single-faced disc label downwards (ie. the wrong way up) and press the OPEN/CLOSE button or the PLAY

button on the unit, “Reading” will appear on the display for 30 seconds and then “Incorrect Disc” will continue to be displayed.

• Some discs may not work the resuming facility.

• Resuming cannot function when you play a PBC-featured Video CD while the PBC is on. To turn off the PBC, see page 36.

• Some playback operations of DVDs may be intentionally fixed by software producers. Since this unit plays DVDs according

to the disc contents the software producers designed, some playback features may not be available. Also refer to the

instructions supplied with the DVDs.

• Do not move the unit during playback. Doing so may damage the disc.

• Use the OPEN/CLOSE button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may

cause the unit to malfunction.

• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the unit to

malfunction.

• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen

menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the

POWER button on your remote control once the movie is completed.

• There may be a slight delay between you pressing the button and the function activating.

5K30501B [E] (P28-32)

20/4/04, 15:33

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic playback

Playing a disc (continued

)

REV

PLAY

FWD

SKIP

PAUSE

SLOW

DVD

VCD

Playing in fast reverse or fast forward directions

To resume normal playback

Press PLAY.

Press REV or FWD during playback.

PLAY

FWD

REV

REV: Fast reverse playback

FWD: Fast forward playback

Notes:

Each time you press REW or FWD

• The TV/DVD mutes sound and subtitles during reverse

and forward scan of DVD video discs. However, the TV/

DVD plays sound during fast forward or fast reverse play

of audio CDs.

button, the playback speed changes.

• The playback speed may differ depending on the disc.

DVD

VCD

Playing frame by frame

To resume normal playback

Press PLAY.

Press PAUSE during still playback.

Each time you press PAUSE, the

picture advances one frame.

PAUSE

PLAY

Note:

The sound is muted during frame by frame playback.

DVD

VCD

Playing in slow-motion

To resume normal playback

Press PLAY.

Press SLOW

during playback.

(REVERSE) or

(FORWARD)

PLAY

SLOW

Each time you press the button, the

slow-motion speed changes.

Notes:

• The sound is muted during slow-motion playback.

• The Video CD can not play Reverse Slow.

DVD

VCD

Locating a chapter or track

Press SKIP

repeatedly to display the chapter or track number you want.

Playback starts from the selected chapter or track.

SKIP

To locate succeeding chapters or

Playback starts from the beginning of

tracks.

the current chapter or track.

When you press twice in quick successions,

playback starts from the beginning of

the preceding chapter or track.

Notes:

• A “Prohibition” symbol

may appear at the upper left of the screen. This symbol means either the feature you tried is not

available on the disc, or the TV/DVD can not access the feature at this time. This does not indicate a problem with the TV/DVD.

• The unit is capable of holding a still video image or On screen display image on your television screen indefinitely. If you leave

the still video image or On screen display image displayed on your TV for an extended period of time, you risk permanent

damage to your television screen. Projection televisions are very susceptible.

5K30501B [E] (P28-32)

20/4/04, 15:33

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced playback

RECALL

0–9

Zooming/Locating desired scene

CANCEL

ZOOM

ENTER

JUMP

DVD

VCD

Zooming

This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the

frame.

Press ZOOM during playback.

Press

to view a different part of the

frame.

The centre part of the image will be

zoomed in.

Each press of ZOOM will change the

ZOOM/CH RTN

You may move the frame from the

centerpositiontoUP,DOWN,LEFTor

RIGHT direction.

CH +

VOL –

VOL +

ZOOM 1 (x 1.3), 2 (x 1.5) and

(x 2.0).

CH –

In the zoom mode press ZOOM repeatedly to

return to a 1:1 view ( Off).

ZOOM/CH RTN

Notes:

• You can select the Pause, Slow or Search playback in the zoom mode.

• Some discs may not respond to zoom feature.

DVD

VCD

Locating desired scene

Use the title, chapter and time recorded on the disc to locate the desired point to play back.

To check the title, chapter and time, press RECALL.

Press JUMP during playback or stop mode.

Press Numbered buttons (0–9) to change the

number.

JUMP

Jump

Time

Title

Chapter

Jump

Time

Title

Chapter

/Enter/0 9/Cancel/Jump

• If you input a wrong number, press

CANCEL.

• Refer to the package supplied with

the disc to check the numbers.

Press

“Chapter”.

to select the “Time”, “Title” or

Jump

Time

Title

Chapter

CH +

CH –

Press ENTER. Playback starts.

/Enter/0 9/Cancel/Jump

ENTER

• When you change the title,

playback starts from Chapter 1

of the selected title.

• Some discs may not work in the

above operation.

Note:

In case of the Video-CD playback with PBC, the JUMP does not work. To turn off PBC, see page

5K30501B [E] (P28-32)

20/4/04, 15:33

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced playback

Repeat playback/A-B Repeat playback

/▼

ENTER

PLAY

PLAY MODE

REPEAT A-B

DVD

VCD

DVD

VCD

Repeat playback

A-B Repeat playback

A-B repeat playback allows you to repeat material between

two selected points.

Press PLAY MODE during playback or stop

mode.

Press REPEAT A-B during playback.

PLAY MODE

The start point is selected.

REPEAT A-B

[DVD]

Press B/A or ENTER once or twice to select

“Chapter” or “Title”.

The unit automatically starts repeat

VOL –

VOL +

playback after finishing the current title

or chapter.

ENTER

Press REPEAT A-B again.

Repeat

/Enter/Play Mode

Off

The end point is selected. Playback

starts at the point that you selected.

Playback stops at the end point, re-

turns to Point A automatically, then

starts again.

REPEAT A-B

[Audio CD, Video CD]

Press D to select “Repeat”.

Press B/A or ENTER once or twice to select

“Track” or “All”.

The unit automatically starts repeat

VOL –

VOL +

playback after finishing the current

track.

CH –

ENTER

Play Mode

Repeat

Off

/Enter/Play Mode

To resume normal playback

Press REPEAT A-B again.

• If you set the repeat mode during stop mode,

press PLAY to start Repeat playback.

REPEAT A-B

“

” appears on the screen.

Off

Press PLAY MODE again to make the screen

disappear.

Notes:

• In A-B Repeat mode, subtitles near the A or B locations may

not be displayed.

• You can not set the A-B Repeat for the scenes that include

multiple angles.

To resume normal playback

• A-B Repeat playback does not work when Repeat playback is

activated.

• You may not be able to set A-B Repeat, during certain scenes

of the DVD.

• A-B Repeat does not work with an interactive DVD.

• A-B Repeat is prohibited when PBC is on.

Select Repeat : “Off” in step 2.

Notes:

• Some discs may not work with the repeat operation.

• In case of Video CD with PBC, repeat functions are prohib-

ited during playback.

5K30501B [E] (P28-32)

20/4/04, 15:33

Download from Www.Somanuals.com. All Manuals Search And Download.

Program playback/Random playback

0–9

You can arrange the playback order of tracks or files on the disc. And also

the unit selects tracks or files at random and playback them. These feature

works for Audio CD and Video CD.

CANCEL

▲/ ▼ /

ENTER

PLAY MODE

SKIP7

PLAY

VCD

Program playback

Press

and press ENTER.

to select “Program Playback”

Press PLAY MODE in the stop mode.

PLAY MODE

The programs you selected will start to playback in

the order.

Press

to select Play Mode, then press

• To resume normal playback, select Play Mode:

“Off” in step 2.

or ENTER to select “Program”.

ENTER

CH +

Play Mode

Repeat

Program

Off

VOL –

VOL +

VOL –

VOL +

1 9

CH –

Clear

Program Playback

/Enter/0 9/Cancel/Play Mode

Press

to select the programming

■ To change the program

1. In the program mode, press C/D/B /A to select the track

number.

position. Use Numbered buttons (0–9) to input

the Track or file numbers.

2. Press Number buttons (0–9) to select the track number to

be replaced.

■ To clear the program one by one

In the program mode, press C/D/B/A to select the track

number. Then press CANCEL.

• To program others, repeat Step 3.

• If you input a wrong number, press

CANCEL.

CH +

VOL –

VOL +

CH –

■ To clear all the programs

In the program mode, press C/D/B/A to select “Clear”. Then

press ENTER.

Notes:

• In playing back the Video CD with PBC, you can not set

Program playback.

• The program is cancelled when you open the disc tray or

turn the power off.

VCD

Random playback

Press PLAY MODE during playback or stop

mode.

Press PLAY.

PLAY

The Random Playback will start.

PLAY MODE

• If you set “Random” during playback mode,

Random playback will begin after the track that is

currently being played has ended.

• To resume normal playback, select Play Mode:

“Off” in step 2.

Press C/D to select Play Mode, then press

B/A or ENTER to select “Random”.

ENTER

CH +

VOL –

VOL +

CH –

Note:

In playing back the Video CD with PBC, you can not set

Random playback.

5K30501B [E] (P33-39)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced playback

Changing angles/Title selection/DVD menu

TOP MENU

ANGLE

DVD MENU

▲/ ▼ /

ENTER

PLAY

Changing angles

Whenplayingbackadiscrecordedwithmulti-anglefacility,youcanchangetheanglethatyouareviewingthescenefrom.

Press ANGLE during playback.

Press ANGLE repeatedly until the desired angle

is selected.

The current angle will appear.

ANGLE

1/9

Note:

Depending on the DVD, you may not be able to change the

angles even if multi-angles are recorded on the DVD.

Title selection

Two or more titles are recorded on some discs. If the title menu is recorded on the disc, you can select the desired title.

Press TOP MENU during playback.

Press ENTER or PLAY.

TOP MENU

The playback of the selected title will

start.

Title menu appears on the screen.

ENTER

PLAY

Press

to select the desired title.

CH +

VOL –

VOL +

Note:

Depending on the DVD, you may not be able to select the title.

Depending on the DVD, a “title menu” may simply be called a

“menu” or “title” in the instructions supplied with the disc.

CH –

DVD menu

Some DVDs allow you to select the disc contents using the menu.

When you play back these DVDs, you can select the subtitle language and sound-track language, etc. using the menu.

Press DVD MENU during playback.

Press ENTER.

The DVD menu appears on the screen.

The menu continues to another

screen. Repeat steps 2 and 3 to set

the item completely.

DVD MENU

ENTER

• Press DVD MENU again to resume

playback at the scene when you

pressed DVD MENU.

Press

to select the desired item.

Note:

Depending on the DVD, you may not be able to resume

playback from the scene point when you pressed the DVD

MENU button.

CH +

VOL –

VOL +

CH –

5K30501B [E] (P33-39)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing soundtrack language/

Subtitles

AUDIO

SUBTITLE

DVD

VCD

Changing soundtrack language

Subtitles

You can select the language when you play a multilin-

gual disc.

When playing back a disc recorded with subtitles, you can

select the subtitle language or turn the subtitle off.

Press AUDIO during playback.

PressSUBTITLErepeatedlyduringplaybackuntil

your desired language appears.

The current soundtrack language will

appear.

AUDIO

SUBTITLE

1/8 Eng

To turn off the subtitle, press SUBTITLE until

“Off” appears.

Press AUDIO repeatedly until the desired lan-

guage is selected.

SUBTITLE

AUDIO

Off

•

The on screen display will disappear after a

few seconds.

• The on screen display will disappear after a few

seconds.

Notes:

• Depending on the DVD, you may not be able to change

subtitles, or to turn subtitles on or off.

• While playing a DVD, the subtitle may change when

you open or close the disc tray.

In case of Video CD playback

Audio type changes as follows each time you press AUDIO.

• In some cases, a selected subtitle language may not

be changed immediately.

Notes:

• If the desired language is not heard after pressing the

button several times, the language is not recorded on

the disc.

• Changing soundtrack language is cancelled when you

open the disc tray. The initial default language or available

language will be heard if the disc is played back again.

• If you select DTS in playing DTS-encoded disc, no sound

will be heard from the TV/DVD’s speakers.

5K30501B [E] (P33-39)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced playback

RECALL

Karaoke playback/Disc status/

To turn off the PBC

AUDIO

ENTER

DVD

VCD

Disc status

Karaoke playback

You can turn the vocal on or off recorded on the DVD

KARAOKE.

With each press of RECALL, the status of the disc

will appear on the screen and change as follows.

RECALL

During DVD KARAOKE disc playback, press

AUDIO.

The KARAOKE symbol ( ) appears.

DVD

AUDIO

00:34:56 01:12:33

1/99 Chapter 1/999

1/9

1/8 Eng Dolby Digital

Title

1/8 EngDolby Digital

1/32 Eng

Off

• If you play non-Karaoke disc, the KARAOKE sym-

bol ( ) does not appear.

• Some Karaoke discs may not have the vocal on/

off function. In this case, the KARAOKE symbol

To make status display disappear, press RECALL

again.

Video CD

(

) does not appear.

00:12

04:32

PBC

00:12

04:32

Track –/–

Press B or A to select “On” or “Off”.

VOL –

VOL +

1/8 Eng Dolby Digital

To make status display disappear, press RECALL

again.

Audio CD

On : The primary vocal is output when it is

recorded on the disc.

Off : The primary vocal is not output.

34:56

71:33

Track 11/99

• The on screen display will disappear after a

few seconds.

When you playback the CD disc, the status display

will appear on the screen and continue displaying.

Notes:

• The vocal output feature is used during playback of Dolby

Digital (multi-channel) recorded DVD KARAOKE discs. This

feature allows you to turn off vocal audio tracks, or restore

them for background accompaniment.

• When playing Karaoke, connect appropriate audio equipment

such as an amplifier to the TV/DVD.

VCD

To turn off the PBC

Press number button 1 in the stop mode, then

press ENTER.

ENTER

5K30501B [E] (P33-39)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Function setup

Customizing the function settings

You can change the default settings to customize performance to your

preference.

SETUP

▲/▼ /

ENTER

RETURN

DVD

VCD

Setting procedure

Press SETUP during stop mode.

Press C or D to select the desired option.

SETUP/MENU

CH +

The following on-screen display

appears.

CH –

Language Picture Sound Parental Other

Change the selection using C/D/B/A or ENTER,

by referring to the corresponding pages 38 and

39.

CH +

/Enter/Setup/Return

• Repeat step 3 and 4 to change

other settings.

• Press C to select another

operation, go back to step 2.

VOL –

VOL +

CH –

Press B or A to select the desired section, then

press D or ENTER.

ENTER

VOL –

VOL +

To make SETUP screen disappear, press

SETUP or RETURN.

CH –

SETUP/MENU

ENTER

RETURN

Page

Section

Option

Details

To select the language of “Menu”, “Subtitle” and “Audio” if

their languages are recorded onto the disc more than one

language.

Language

Subtitle

Audio

Tv Screen

Display

To select a picture size according to the aspect ratio of your TV.

Picture

To turn on or de-activate the operational status display on the

screen.

Sound

Parental

Other

DRC

To select On or Off for DRC (Dynamic Range Control).

Input 4-digit password to set the parental level.

Password

Parental

To select a preferred parental level for the parental setting.

To select a preferred language for on screen display.

OSD language

5K30501B [E] (P33-39)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Function setup

Customizing the Function Settings (continued)

Setting details

Language Picture Sound Parental Other

Picture

Language

Tv Screen

Display

4:3

16:9

Subtitle

Audio

English

Automatic Francais

English

Espanol

Other

/Enter/Setup/Return

Menu, Subtitle, Audio

Tv Screen

You can select the language of “Menu”, “Subtitle” and

“Audio” if more than one languages are recorded onto

the disc.

You have the following screen sizes to choose from:

4:3 Letter box:

Select this mode when connecting to a conventional TV.

When playing back a wide screen-DVD disc, it displays

the wide picture with black bands at the top and bottom

of screen.

English, Francais, Espanol:

The selected language will be heard or seen.

Other:

Other language can be selected (see the “Language

code list” on page 41).

4:3

Pan scan:

It displays the wide picture on the whole screen with left

and right edges automatically cut off.

Original: (Audio)

The unit will select the first priority language of each

disc.

16:9

Wide:

Automatic: (Subtitle)

Select this mode when connecting to a wide-screen TV.

A wide screen picture is displayed full size.

•

The unit will automatically select the same

language in the AUDIO setting.

• When the unit selects the same language as

the AUDIO, the subtitles will not appear during

playback.

Note:

If the DVD disc is not formatted in the pan & scan style, it

displays 4:3 style.

• When you do not use the same language as

the AUDIO, the subtitles will appear during

playback.

Display

On screen display can be switched on or off when you

press the buttons.

Off: (Subtitle)

Subtitles do not appear.

On: On screen displays appear when you press the

buttons (factory setting).

Note:

Off: On screen displays do not appear when you

press any buttons.

If the selected language is not recorded on the disc, the

first-priority language is selected.

5K30501B [E] (P33-39)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting details

To change the parental level

Language Picture Sound Parental Other

Sound

1) Press C or D to select “Password”.

2) Press Number buttons (0–9) to enter the password

you have stored.

Off

DRC

3) Press ENTER.

/Enter/Setup/Return

• The rating is now unlocked.

4) Press C or D to select “Parental”, then press B

or A to change the parental level.

5) Press C or D to select “Password”, then press

Number buttons (0–9) to enter the password.

Note: You can change the password if you want.

6) Press ENTER.

DRC

DRC (Dynamic Range Control) enables you to control

the dynamic range so as to achieve a suitable sound for

your equipment.

On: Loud sound such as explosion or similar is toned

down slightly when played back. This makes it

suitable for when it is connected to a stereo.

Now the parental level is changed and locked.

If you forget the password...

1. Press OPEN/CLOSE to open the disc tray.

2. Remove the disc.

3. Press OPEN/CLOSE again to close the disc tray.

“No Disc” appears on the screen.

4. While holding STOP down on the front panel, press 7

on the remote control. “PASSWORD CLEAR” appears

on the screen.

Off: It plays back at the recording level on the disc.

Notes:

• This function works only during playback of Dolby Digital

recorded discs.

• The level of Dynamic Range Reduction may differ

depending on DVD video disc.

5. Enter a new password again.

Language Picture Sound Parental Other

Parental

Notes:

Password

• Depending on the discs, the unit may not be able to limit

playback.

Parental

Off

• Some discs may not be encoded with specific rating level

information though its disc jacket says “adult.”

For those discs, the parental control feature will not work.

9/Cancel

/Enter/Setup/Return

Parental control setting

Some discs are specified not suitable for children.

Suchdiscscanbelimitednottoplaybackwiththeunit.

Language Picture Sound Parental Other

Other

1) Press C or D to select “Parental”, then press B

OSD Language English

English

Francais

Espanol

or A until the level you require appears.

• Level Off:

The parental control setting does not

function.

/Enter/Setup/Return

• Level 8:

• Level 1:

All DVD software can be played back.

DVD software for adults cannot be

played back.

OSD Language

The setup language can be selected.

Select from the level 1 to level 8. The limitation will

be more severe as the level number is lower.

2) Press C or D to select “Password”.

Press Number buttons (0–9) to input a 4-digit

password. Be sure to remember this number!

• If you input a wrong number, press CANCEL.

3) Press ENTER to store the password.

Note: Now the rating is locked and the setting can

not be changed unless you enter the correct pass

word.

English: To display OSD language is English.

Francais: To display OSD language is Francais.

Espanol: To display OSD language is Espanol.

Note:

If each setup (pages 38 and 39) has been completed, the unit

canalwaysbeworkedunderthesameconditions(especially

with DVD discs).

Each setup will be retained in the memory even if you turn

the power off.

Notes:

• Depending on the discs, the unit cannot limit playback.

• Some discs may not be encoded with specific rating

level information though its disc jacket says “adult.” For

those discs, the age restriction will not work.

5K30501B [E] (P33-39)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Function setup

Temporary disabling of rating level by DVD disc

0–9

OPEN/CLOSE

Depending on the DVD disc, the disc may try to temporarily cancel the rating

level that you have set.

It is up to you to decide whether to cancel the rating level or not.

▲/▼

ENTER

RETURN

PLAY

Load a DVD disc and press PLAY or OPEN/

CLOSE on the unit (see page 28).

Enter the password with number buttons (0–9).

4_{Then press ENTER.}

If you interrupt the entering, press

RETURN.

PLAY

Please enter the

OPEN/CLOSE

digit password

ENTER

Enter/0 9/Cancel/Return

IftheDVDdischasbeendesignedtotemporarily

canceltheRatinglevel, thescreenwhichfollows

the “Reading” screen will change, depending on

which disc is played. If you select “YES” with the

ENTER key, “Your disc exceeds the parental

control level#.” screen will then appear.

RETURN

Playback will commence if the entered

password was correct.

Reading

Your disc exceeds

the parental control level#.

Parental Control Level

Cancel Picture

Note:

This temporary cancellation of rating level will be kept until the

disc is ejected.

/Enter/Return

When the disc is ejected, the original rating level will be set again

automatically.

If you wish to cancel the set rating level temporarily,

select “Parental Control Level” with

, then

press ENTER. If the 4-digit password at step 2 on

page 39 has been set, the password entering

screen will appear as shown in step 4.

Alternatively, if the password has not been set,

playback will commence. If you don’t know (or have

forgotten) the password, select “Cancel Picture”.

The setting screen will disappear. Press OPEN/

CLOSE to remove the disc.

CH +

CH –

ENTER

OPEN/CLOSE

5K30501B [E] (P40-41)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Language code list

Enter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio” (see pages 38).

Language Name Code Language Name Code Language Name Code Language Name Code

Abkhazian

Afar

1112 Fiji

1620 Lingala

1619 Lithuanian

1628 Macedonian

1635 Malagasy

1722 Malay

2224 Singhalese

2230 Slovak

2321 Slovenian

2317 Somali

2329 Spanish

2322 Sundanese

2330 Swahili

2319 Swedish

2328 Tagalog

2325 Tajik

2919

2921

2922

2925

1529

2931

2933

2932

3022

3017

3011

3030

3015

3018

1225

3019

3025

3028

3021

3033

3121

3128

3136

3219

3225

1335

3325

3418

2019

3525

3631

1111 Finnish

1116 French

2927 Frisian

1123 Galician

1128 Georgian

1835 German

1129 Greek

1135 Greenlandic

1136 Guarani

1211 Gujarati

1531 Hausa

Afrikaans

Albanian

Amharic

Arabic

2111 Malayalam

1415 Maltese

1522 Maori

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

2122 Marathi

1724 Moldavian

1731 Mongolian

1811 Nauru

2324 Tamil

Basque

2411 Tatar

Bengali; Bangla 1224 Hebrew

1933 Nepali

2415 Telugu

2425 Thai

Bhutani

Bihari

1436 Hindi

1819 Norwegian

1831 Oriya

1218 Hungarian

1228 Icelandic

1217 Indonesian

2335 Interlingua

1215 Irish

2528 Tibetan

2611 Tigrinya

Breton

1929 Panjabi

Bulgarian

Burmese

Byelorussian

Cambodian

Catalan

Chinese

Corsican

Croatian

Czech

1924 Pashto, Pushto 2629 Tonga

1911 Persian

1711 Polish

1611 Turkish

2622 Turkmen

2630 Twi

2123 Italian

1930 Portuguese

2011 Quechua

1311 Japanese

3618 Javanese

1325 Kannada

1828 Kashmiri

1329 Kazakh

1411 Kirghiz

2422 Korean

1524 Kurdish

1525 Laothian

1530 Latin

2731 Ukrainian

2033 Rhaeto-Romance2823 Urdu

2124 Romanian

2129 Russian

2121 Samoan

2135 Sanskrit

2125 Scots Gaelic

2131 Serbian

2825 Uzbek

2831 Vietnamese

2923 Volapük

2911 Welsh

1714 Wolof

Danish

Dutch

English

2928 Xhosa

Esperanto

Estonian

Faroese

2225 Serbo-Croatian 2918 Yiddish

2211 Shona

2924 Yoruba

2914 Zulu

1625 Latvian, Lettish 2232 Sindhi

5K30501B [E] (P40-41)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Problems and troubleshooting

Use the following check list for troubleshooting when you have problems with your unit. Consult your local dealer

or service outlet if problems persist.

Be sure all connections are properly made when using with other units.

SYMPTOMS

POSSIBLE SOLUTIONS

PAGE

POWER

• Make sure the power cord is plugged in.

• Try another AC outlet.

• Power is off, check fuse or circuit breaker.

• Unplug unit, then plug it back in.

TV/DVD does not operate.

TV BROADCAST RECEPTION

• Station or Cable TV experiencing problems, tune to another station. 14

Poor sound or No sound.

• Check Volume adjustments.

• Check for sources of possible interference.

• Station or Cable TV experiencing problems, tune to another station.

• Check antenna or Cable TV connections, reorient antenna.

• Check for sources of possible interference.

Poor picture or No picture.

• Check picture control adjustments.

•

Station or Cable TV experiencing problems, tune to another station. 14

Poor reception on some channels.

• Station signal is weak, reorient antenna to receive weaker station. 13,14

• Check for sources of possible interference.

• Station or Cable TV experiencing problems, tune to another station.

• Make sure channels are set into memory.

• Check picture control adjustments.

• Check antenna or Cable TV connections, reorient antenna.

• Check for sources of possible interference.

Poor color or no color.

–

• Station or Cable TV experiencing problems, tune to another station.

• Make sure channels are set into memory.

• Cable TV company is scrambling signal.

• Check antenna orientation.

• Check all Cable TV connections.

• Set TV/CABLE selection to the CABLE position.

• Station or Cable TV system problems, try another station.

Picture wobbles or drifts.

No CATV reception.

Horizontal or diagonal bars on

screen.

• Check antenna connections, reorient antenna.

• Check for sources of possible interference.

13,14

• Make sure TV/CABLE selection is in the appropriate position.

• If using antenna, check UHF antenna connections.

No reception above channel 13.

• No broadcast on station tuned.

• Sleep Timer is set.

• Power interrupted.

–

TV shuts off.

• TV station experiencing problems or program tuned is not closed

captioned. Try another channel.

• Check Cable TV connection or VHF/UHF antenna, reposition or

rotate antenna.

• Press CLOSED CAPTION button to turn on the closed caption

decoder.

13,14

Closed - Caption is not activated.

Display is not shown in your

language.

• Select proper language in the menu options.

5K30501B [E] (P42-45)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Problems and troubleshooting (continued)

SYMPTOMS

POSSIBLE SOLUTIONS

PAGE

DVD

• No disc is inserted.

• The disc may be dirty. Clean up the disc.

• The unit cannot play CD-ROMs, etc.

Playback doesn’t start.

No picture.

• TV/DVD selector is not set correctly.

• Check the input selector of the amplifier is set properly.

• The unit is in the Advanced playback mode.

• Select the correct Audio Output position on AV amplifier.

–

No sound.

Picture is distorted during fast

reverse/forward playback.

• The picture will be distorted occasionally.

–

Stopping playback, search, slow-

motion play, repeat play, or

program play, etc. cannot be

performed.

• Some discs may not do some of the functions.

–

No 4:3 (16:9) picture.

No on-screen display.

No surround sound.

• Select appropriate screen size.

• Select Display On.

• The setup does not match your stereo system.

The unit or remote operation key

is not functioning.

• Turn off the unit and unplug the AC power cord for several min-

utes, then replug it.

–

Playback does not start when the

title is selected.

• Check the RATING LEVEL setup.

Audio soundtrack and/or subtitle

language is not changed when

you play back a DVD.

• Multilingual language is not recorded on the DVD disc.

• Some discs have no subtitles.

• Subtitles are cleared. Press the SUBTITLE button.

No subtitle.

Angle cannot be changed.

• Multi-angles are not recorded on the DVD disc.

• The function is prohibited with the unit or the disc.

“

” appears on the screen.

REMOTE CONTROL

The remote control does not

function.

• Aim at the remote control at the remote sensor.

• Operate within approx. 5 meters or reduce the light in the room.

• Clear the path of the beam.

• The batteries are weak. Replace the batteries.

• Check the batteries are inserted correctly.

5K30501B [E] (P42-45)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Reception disturbances

Most types of television interference can be remedied by adjusting the height and position of the VHF/UHF

antenna. Outdoor antennas are recommended for best results. The most common types of television

interference are shown below. If one of these symptoms appear when the TV/DVD is connected to a Cable

TV system, the disturbance may be caused by the local Cable TV company broadcast.

IGNITION

Black spots or horizontal streaks may appear, the picture may flutter or

drift. Usually caused by interference from automobile ignition systems,

neon lamps or AC powered tools and appliances such as drills or hair

dryers.

GHOSTS

Ghosts are caused by the television signal following two paths. One is

the direct path and the other is reflected by tall buildings, hills or other

large objects. Changing the direction or position of the antenna may

improve the reception.

SNOW

If the TV/DVD is located far from the TV station, in a fringe reception

area where the signal is weak, small dots may appear in the picture.

If the signal is extremely weak, the installation of a larger external

antenna may be necessary.

RADIO FREQUENCY INTERFERENCE (RFI)

Caused by two-way radios, this type of interference produces moving

ripples or diagonal streaks in the picture. Some cases may cause a

loss of contrast in the picture. Changing the direction and position of

the antenna or installing an RFI filter may improve the picture.

PICTURE SIZE VARIATION

A slight picture size variation is normal when you adjust the CONTRAST

or BRIGHTNESS settings.

CARE AND MAINTENANCE

To prevent fire or shock hazard, disconnect the TV/DVD from the power source before cleaning.

The finish on the cabinet may be cleaned with mild soap and a soft, damp cloth and cared for as other furniture.

Use caution when cleaning or wiping the plastic parts.

5K30501B [E] (P42-45)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

General

Power supply

Power consumption

Picture tube

Speaker

Audio output power

Weight

AC 120 V 60 Hz

Operation: 75 W, Stand by: 5 W

Type 13 (335.4 mm diagonal)

1-1/2 x 2-11/16 inches (38 x 69 mm), 8 ohm x 2

1.5 W + 1.5 W

24.3 lbs (11.0 kg)

Dimensions

Width: 14-1/4 inches (362 mm)

Height: 15-1/16 inches (382 mm)

Depth: 14-3/8 inches (365 mm)

181 channel freq. synthesized

Tuner

VHF

2-13

UHF

CATV

14-69

125 Channels

Antenna input

UHF/VHF: 75 Ω coaxial

Applicable disc

DVD (12 cm, 8 cm), CD (12 cm, 8 cm)

Frequency range

Operating conditions

DVD: 4 Hz-22 kHz, CD: 4 Hz-20 kHz

Temperature: 5˚C-40˚C (41˚F-104˚F), Operating status: Horizontal

Input/Output

Video input

1.0 V (p-p), 75 Ω, negative sync., pin jack x 1

–8 dBm, 50 kΩ, negative sync., pin jack (L/R) x 1

0.5 V (p-p), 75 Ω, pin jack x 1

Audio input

Audio output (DIGITAL COAXIAL)

Supplied accessories

Remote control (DC-FN20S) ................................ 1

Batteries (AAA) ..................................................... 2

300-75 Ω matching transformer ............................ 1

• Designs and specifications are subject to change without notice.

5K30501B [E] (P42-45)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY TOSHIBA COMBINATION TELEVISION

AND DVD/CD PLAYER

Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties. These limited

warranties extend to the original consumer purchaser or any person receiving this set as a gift from the original

consumer purchaser and to no other purchaser or transferee.

Limited Ninety (90) Day Warranty

TACP warrants this product and its parts against defects in materials or workmanship for a period of ninety (90)

days after the date of original retail purchase. During this period, TACP will repair a defective product or part,

without charge to you. You must deliver the entire set to an Authorized TACP Service Station. You pay for all

transportation and insurance charges for the set to and from the Service Station.

Limited One (1) Year Warranty

TACP further warrants the parts in this product against defects in materials or workmanship for a period of one

year after the date of original retail purchase. During this period TACP will replace a defective part without

charge to you, except that if a defective part is replaced after ninety (90) days from the date of original retail

purchase you pay labor charges involved in the replacement. You must also deliver the entire product to a

TACP Authorized Service Station. You are responsible for all transportation for the set to and from the Service

Station.

Limited Two (2) Year Warranty of Picture Tube

TACP further warrants the picture tube in this product against defects in materials or workmanship for a period

of two (2) years after the date of original retail purchase. During this period, TACP will replace a defective

picture tube without charge to you except that if a defective picture tube is replaced after ninety (90) days from

the date of the original retail purchase, you pay labor charges involved in the replacement. You are responsible

for all charges involved in the replacement. You are responsible for all transportation and insurance charges for

the set to and from the Service Station.

Rental Units

The warranty for rental units begins with the first rental or thirty (30) days from the date of shipment to the rental

firm, whichever comes first.

Commercial Units

Products sold and used for commercial use have a limited ninety (90) day warranty for all parts, labor and picture

tube.

Owner's Manual and Demographic Card

You should read this owner's manual thoroughly before operating this product. You should complete and mail

the enclosed Demographic card within ten days after you, or the person who has given you this product as a

gift, purchased this product. This is one way to enable TACP to provide you with better customer service and

improved products. Failure to return the Demographic card will not affect your rights under this warranty.

Your Responsibility

The above warranties are subject to the following conditions:

( 1 ) You must retain your bill of sale or provide other proof of purchase.

( 2 ) All warranty servicing of this product must be made by an Authorized TACP Service Station.

( 3 ) These warranties are effective only if the product is purchased and operated in the U.S.A. or Puerto Rico.

( 4 ) Labor service charges for set installation, set up, adjustment of customer controls and installation or repair

of antenna systems are not covered by this warranty. Reception problems caused by inadequate antenna

systems are your responsibility.

( 5 ) Warranties extend only to defects in materials or workmanship as limited above and do not extend to any

product or parts which have been lost or discarded by you or to damage to products or parts caused by

misuse, accident, damage caused by Acts of God, such as lightning or fluctuations in electric power,

improper installation, improper maintenance or use in violation of instructions furnished by us; or to units

which have been altered or modified without authorization of TACP.

5K30501B [E] (P46-Back)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

How to Obtain Warranty Service

If after following all of the operating instructions in this manual and checking the section “Problems and

troubleshooting” and you still find that service is needed;

( 1 ) Call the TACP toll free number 1-800-631-3811 after you find a defective product or part to find

the nearest Toshiba Authorized Service Station.

( 2 ) Please present your bill of sale or other proof to the Authorized Service Station.

“TACP Authorized Service Station personnel will come to your home when warranty service is

required. Depending on the type of repair required, the service will either be performed in your

home or the set will be taken to the TACPAuthorized Service Station for repair and returned to your

home at no cost to you”.

In the Continental United States contact:

Toll Free

1-800-631-3811

All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular

purpose, are expressly limited to the duration of the limited warranties set forth above. With the exception of any

warranties implied by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warran-

ties, guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair or replace-

ment of any parts. In no event shall TACP be liable for consequential or incidental damages.

No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these

warranties in any manner whatsoever. The time within which action must be commenced to enforce any obliga-

tion of TACP arising under this warranty or under any statute, or law of the United States or any state thereof, is

here by limited to 90 days from the date you discover or should have discovered, the defect. This limitation does

not apply to implied warranties arising under state law.

This warranty gives you specific legal rights and you may also have other rights which may vary from state to

state. Some states do not allow limitation on how long an implied warranty lasts, when an action may be

brought, or the exclusion or limitation of incidental or consequential damages, so the above provisions may not

apply to you.

ATTENTION CANADIAN CONSUMERS:

Canadian consumers are requested to complete the special Canadian “Warranty Registration

Form” enclosed, and forward this completed form with a copy of bill of sale to TOSHIBA OF

CANADA to “Register and Validate” their warranty.

Products purchased in the U.S.A. and used in Canada are not covered by these warranties.

Products purchased in Canada and used in the U.S.A. are not covered by these warranties.

Rev. 09-01-98

5K30501B [E] (P46-Back)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

04/02

5K30501B [E] (P46-Back)

20/4/04, 15:34

Download from Www.Somanuals.com. All Manuals Search And Download.

Technicolor Thomson MP3 Player PDP2069 User Manual
Toastmaster Electric Heater 9451 HP34CDNF User Manual
Toshiba Network Hardware Network Video Recorder User Manual
Trane Air Conditioner LO User Manual
Transcend Information Network Card TS0MSM2PC User Manual
Unitech Barcode Reader MR550 User Manual
V7 TV Mount V7MBK2LPCB User Manual
ViewSonic Computer Monitor VA2013WM User Manual
ViewSonic Flat Panel Television NX1940w User Manual
Walker Lawn Mower MT MTL MTEFI MTLEFI User Manual