INSTRUCTION MANUAL
DOME CAMERA
ZEIM-4000100G A.1
IK-DF02A
Please read this manual thoroughly before use, and keep it handy
for future reference.
Record in space provided below the Model # and
the Serial # as found on the label on the bottom of
this unit.
Model # IK-DF02A
Serial #
Retain this information for future reference.
TABLE OF CONTENTS
IMPORTANT SAFEGUARDS........................................ 1
1. FEATURES AND DESCRIPTION ................................. 4
2. COMPONENTS ............................................................ 4
3. PART NAMES AND FUNCTIONS ................................ 5
4. CONNECTIONS ........................................................... 6
5. INSTALLATION ............................................................. 8
6. BACKLIGHT COMPENSATION (BLC) ......................... 16
7. LINE LOCK PHASE ...................................................... 16
8. NOTES ON USE AND INSTALLATION ........................ 17
9. IN CASE OF PROBLEMS ............................................ 18
10. SPECIFICATIONS ........................................................ 19
11. EXTERIOR VIEW ......................................................... 20
For information on the latest our products and peripheral devices, refer to
the following Web page.
The above URL is subject to change without prior notice. If the URL changes,
refer to the Toshiba website
(http://www.toshiba.com.)
Download from Www.Somanuals.com. All Manuals Search And Download.
• The CAUTION label, shown on the left,
is attached on the camera.
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightening flash with arrowhead
WARNING :
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage”within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION :
CONNECT 24V AC UL LISTED CLASS 2
POWER SUPPLY.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
FIELD INSTALLATION MARKING :
WORDED: "THIS INSTALLATION
SHOULD BE MADE BY A QUALIFIED
SERVICE PERSON AND SHOULD
CONFORM TO ALL LOCAL CODES."
FCC (USA)-INFORMATION
NOTE : This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
USER-INSTALLER CAUTION :Your authority to operate this FCC verified equipment could be
voided if you make changes or modifications not expressly approved by the party.
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Disclaimer
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by
the user in any of the following cases:
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether
intentional or accidental; use under extreme operating conditions.
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including
but not limited to loss of expected income and suspension of business activities.
3. Incorrect use not in compliance with instructions in this instruction manual.
4. Malfunctions resulting from misconnection to other equipment.
5. Repairs or modifications made by the user or caused to be made by the user and carried out by
an unauthorized third party.
6. Notwithstanding the foregoing, Toshiba’s liabilities shall not, in any circumstances, exceed the
purchase price of the product.
Copyright and Right of Portrait
There may be a conflict with the Copyright Law and other laws when a customer uses, displays,
distributes, or exhibits an image picked up by the camera without permission from the copyright
holder. Please also note that transfer of an image or file covered by copyright is restricted to use
within the scope permitted by the Copyright Law.
Protection of Personal Information
Images taken by the camera that reveal the likeness of an individual person may be considered
personal information. To disclose, exhibit or transmit those images over the internet or otherwise,
consent of the person may be required.
Usage Limitation
The product is not designed for any “critical applications.” “Critical applications” means life support
systems, exhaust or smoke extraction applications, medical applications, commercial aviation,
mass transit applications, military applications, homeland security applications, nuclear facilities
or systems or any other applications where product failure could lead to injury to persons or loss of
life or catastrophic property damage. Accordingly, [Toshiba/TAIS] disclaims any and all liability
arising out of the use of the product in any critical applications.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1. FEATURES AND DESCRIPTION
1. 24V AC/12V DC dual-voltage capability extends power options.
2. Camera has the ability to automatically switch to color in daylight or black and white at night.
3. Camera synchronization mode is selectable between internal and line lock.
4. Back Light Compensation (BLC) adjusts for strong backlight conditions.
5. White balance is automatically adjusted depending on color temperature variations (AWB).
6. Built-in varifocal lens with auto-iris. Focal length 2.8 ~ 10 mm.
7. Built-in 1/3 inch high resolution CCD.
8. Minimum illumination of 0.5 lux with smoke cover.
9. S/N ratio of 50dB.
2. COMPONENTS
(1) Camera ................................................. 1
(2) Accessories
(a) Instruction Manual ........................... 1
(b) Screws ............................................. 4
(c) Monitor Out Harness Wire ............... 1
(d) Instruction (Tamper Resistant) ........ 1
(e) Wire Tie ........................................... 2
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. PART NAMES AND FUNCTIONS
Power Input
Wire
Connect the power
cable to 24V AC or
12V DC.
Length: approx.
12 inches (300mm)
Video Wire (BNC Tap)
Connect the video cable to a
monitor or video device.
The image is outputted when
powered on.
Pan ADJ Screw
Turn the ring-type screw to
adjust the lens pan angle.
Fasten and lock it after
Length: approx. 12 inches (300mm)
completing the adjustment.
Horizontal ADJ Ring
Turn the ring to adjust the
horizontal angle of image.
Mode Setting Switch
1 2 3 4
Lens Iris ADJ
Use to compensate for
the iris level.
ON
OFF
Turn toward L (low) for a
darker picture.
Turn toward H (high) for a
brighter picture.
Optimum value is
adjusted at the default
setting.
1: BLC (Backlight Compensation Control)
When switched on, it automatically
adjusts to compensate for subjects
that are lit from behind.
2: AGC (Auto Gain Control)
When switched on, it automatically
adjusts the image in relation to the
brightness of the subject.
V Phase ADJ
Adjust the phase
difference between this
camera and other
cameras in Line Lock
mode.
3: DC/AES
Not available for this camera.
Be sure to switch to ON.
4: LL (Line Lock)
When switched on, its function is
activated. Line Lock is available
with 24V AC only.
Tilt ADJ Screws
Turn the screws to adjust the lens
tilt angle. Fasten and lock them
after completing the adjustment.
MON (Monitor Out)
When installing the camera, it is
available to check the image with
monitor out harness wire.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4. CONNECTIONS
Notes on connecting
• Power plugs of connected equipment must be disconnected before camera
installation.
• A 75-ohm coaxial cable with connector (3C-2V or 5C-2V) is required for standard
connection.
• For details of wiring and operation of equipment to be connected, refer to their
operation manuals.
• A power supply with cable, connectors and coaxial cable are not supplied with the
camera.
4-1. Basic connection single system configuration
Display Monitor
BNC Connector
1Red
Connector
24V AC UL Listed Class 2 power supply
or
12V DC power supply.
2Black
(*) Recommended power cord is a minimum wire size of 18 AWG.
Connector
1 Red wire
2 Black wire
24V AC
12V DC
Positive
Negative
24V AC (L)
24V AC (N)
CAUTION: Never input 24V AC and 12V DC at the same time.
Do not overload power supply
The recommended power supplies for this camera are 6 watt minimum for each 24V
AC UL Listed Class 2 power supply or 12V DC power supply.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2. Line lock Control
• Matching the vertical synchronization with the power frequency is called the Line Lock.
• To activate the line lock, set the LL switch to ON.
1 2 3 4
ON
OFF
LineLock
• When two or more cameras are switched by the video switcher for viewing with a display monitor
the vertical synchronization phase can be locked to the power frequency for a stable vertical
synchronization.
Display Monitor
Video Switcher
BNC Connector
Camera 1
Connector
To 24V AC UL Listed
Class 2 power supply.
Camera 2
• When connecting to DC power supply,
the Line Lock function is not activated.
Note:
• The camera is synchronized to the power frequency of 60 1 Hz covering a normal fluctuation of
the power frequency. However, the camera may not cover a large fluctuation caused from the
power generated by a generator, etc.
• It takes approximately 10 seconds or more until a stable synchronization is obtained after the
power is turned on.This is normal, because several seconds are required to stabilize the camera
against power noise.
• Refer to section 7. "LINE LOCK PHASE" for adjustment instructions.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5. INSTALLATION
Note: The attached screws are used to install the camera to a solid surface. If installing to surfaces
of loose or thin materials, use the appropriate anchors (not included) with the screws.
5-1. Installing the Camera
5-1-1.Tamper Resistant Feature
Enabling the Tamper Resistant Feature
1. To remove the cover, rotate the
P
Upside
cover counter clockwise.
Pull on the cover to remove it from
the base.
2. Move "Lock Pin" with a screwdriver
from "Unlock" position to "Lock"
position.
3. Align the "Unlock-button" with
position "P". (Refer to the left
figure.)
4. Rotate the cover clockwise to lock
the cover to the base.
Lock Pin
Unlock-button
Base
Cover
Cover Removal with the Tamper Resistant Feature Enabled
Caution: Pulling on the cover with excessive force can cause the inner connector to break.
To remove the cover.
Unlock-button
Cover
1. Unlock the cover by pressing the
"Unlock-button" with a screwdriver.
2. While the "Unlock-button" is
depressed rotate the cover
counter clockwise.
3. Pull on the cover to remove it from
the base.
Screwdriver
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
To Determine Which Set of Mounting Holes to Use
There are two different sets of mounting holes (i and ii).
The set to use depends if the camera is being mounted to a switch box or not and to a wall or
ceiling.
Note: When determining the orientation of the switch box take into consideration the viewing angle
of the unlock-button. If possible, conceal the unlock-button.
Mounting Holes (i)
• Installation to a wall or ceiling.
(Refer to section 5-1-2.)
• Installation to a switch box
Upside
positioned normally on a wall.
TOP mark
This mark is supposed
to be upside.
(Refer to section 5-1-3 (i).)
• Installation to a switch box
attached to a ceiling.
(Refer to section 5-1-3 (i) for
switch box orientation.)
Wire Hole
Mounting Holes (ii)
• Installation to a switch box positioned sideways on a wall.
(Refer to section 5-1-3 (ii).)
• Installation to a switch box attached to a ceiling.
(Refer to section 5-1-3 (ii) for switch box orientation.)
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5-1-2. Installation to a Wall or Ceiling
1.81(46)
0.71(18)
Wire Access Hole
Upside
0.21(5.3)
3.29(83.5)
1.65(42)
To mount the camera directly on the
wall or ceiling.
1. Prepare the mounting space.
2. Place the camera on the wall or
ceiling and mark four screw
positions with a pen.
Dimensions: inch (mm)
3. Attach the camera with the four
screws to the wall or ceiling.
4. Fasten all the screws.
Screw x4
Note: Verify that the word "TOSHIBA" is on the visible side. When mounting on a wall, orient the
camera to face the unlock-button.
(i) Rerouting the Wires for Flush Mounting the Camera
A: Routing the Wires to the Right Side
Upside
1. Remove the wires from the wire
hole and position them to the right
of the base.
2. Firmly secure the wires with the
wire tie.Do not overtighten the wire
Wire Hole
tie.
Wires
Base
Wire Tie
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
B: Routing the Wires to the Left Side
Upside
1. Remove the wires from the wire
hole and position them to the left
of the base.
2. Firmly secure the wires with the
wire tie.Do not overtighten the wire
tie.
Wire Hole
Wire Tie
Base
(ii) Notching Out a Hole for the Wires
Upside
• Cut out the knock out, "A" for the
right side or "B" for the left side, for
the wires.
Unlock-button
A
B
B
A
Unlock-button
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5-1-3. Installation to a Switch Box
(i) Mounting the Camera to a Switch Box Positioned Normally on a Wall
1.81(46)
Switch Box
Upside
3.29(83.5)
Dimensions: inch (mm)
1. Install the switch box.
2. Set the "Upside" on the base to
the up position.
3. Attach the camera to the switch
box with the four mounting screws.
Mounting Screw x 4
(not supplied)
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
(ii) Mounting the Camera to a Switch Box Positioned Sideways
Upside
Switch Box
3.29(83.5)
1.81(46)
Dimensions: inch (mm)
Mounting Screw x 4
(not supplied)
1. Install the switch box positioned sideways on
a wall.
2. Attach the four mounting screws to the switch
box.
3. Positioning the "Upside" at the top, move the
screws through the base and turn the base
clockwise.
4. Fasten all the mounting screws.
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
(iii) Mounting the Camera to a Switch Box Attached to a Ceiling
Ceiling
(i)
1. Position the cover to conceal the
unlock-button from the visible side.
2. Use the mounting holes (i) or (ii)
depending on the direction of the
switch box.
(Refer to section 5-1-3 (i) or (ii).)
3. Attach the camera to the switch
box with the four mounting screws.
Note:Verify that the word "TOSHIBA"
is on the visible side.
Mounting Screw x 4
(not supplied)
(ii)
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2. Adjusting the Viewing Angle
Tilt rotation
5Focus Lock Lever
Tele
Far (∞)
2Tilt Lock
Near
Wide
Horizontal
rotation
3Zoom Lock
Lever
4Horizontal
ADJ Ring
1Pan Lock
Top mark
To Monitor
2Tilt Lock
Pan
(1) To check the video image on the monitor, connect the "Monitor Out Harness Wire" to the
connector "MON".
(2) The lens pan direction can be adjusted by turning pan lock 1 counter clockwise to loosen it
without moving the lens. Retighten after adjusting.
Note:
• Do not turn the lens over 360°, otherwise the inner connector may break and the camera
will be damaged.
(3) Tilt angle of the lens can be adjusted within the limit of -73° to +73° by loosening the tilt lock 2.
After adjusting, tighten the tilt lock 2.
(4) Adjust the zoom position by loosening the zoom lock lever 3. After adjusting, tighten the zoom
lock lever 3.
(5) When installing the camera on a wall, manipulate the horizontal ADJ ring 4 to adjust the
inclination of the image.
(6) Adjust the focus by loosening the focus lock lever 5. After adjusting, tighten the focus lock
lever 5.
(7) Repeat the adjustments from step (1) to step (5) till the optimum image appears.
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
6. BACKLIGHT COMPENSATION (BLC)
To activate backlight compensation, set the BLC switch to ON.
1 2 3 4
ON
OFF
BLC
When the automatic electronic iris feature is used with an auto iris lens, the exposure
adjustment is automatically performed so that a best picture is obtained at a monitor zone of
about 50% in horizontal and about 50% in vertical direction.
This feature is effective when a strong light enters the portion other than this zone and auto iris
lens closes and darkens the viewing area.
Display Monitor
50%
50%
7. LINE LOCK PHASE
If two or more cameras within a system have different AC line phases and they are switched by
a video switcher, the picture on the display monitor will fluctuate vertically.
Connect 24V AC input lines of all cameras so that they all share the same phase.
If you still have vertical fluctuation, adjust the V PHASE controller.
Upside
V PHASE Controller
Note: Refer to section 4-2. "Line Lock Control".
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
8. NOTES ON USE AND INSTALLATION
• Do not aim the camera at the sun
Never aim the camera at the sun even with the camera power off.
• Do not shoot intense light
Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on
the screen. However, this is not a malfunction.
• Treat the camera with care
Do not drop the camera or subject it to intense vibration.
• Never touch internal parts
Do not touch the internal parts of the camera other than the parts specified.
• Do not splash water on the camera
Install the camera where the camera can be kept dry. If the camera gets wet, turn off the power
and contact your dealer.
• Keep the camera installation away from video noise
If cables are wired near electric lighting wires or a TV set, noise may appear in images. In this
event, relocate cables or reinstall equipment.
• Check the ambient temperature and humidity
Avoid using the camera where the temperature is hotter or colder than the specified operating
range. Doing so could affect the internal parts or cause the image quality to deteriorate. Special
care is required to use the camera at high temperature and humidity.
• Should you notice any trouble
If any trouble occurs while you are using the camera, turn off the power and contact your dealer.
If you continue to use the camera when there is something wrong with it, the trouble may get
much worse and an unpredictable problem may occur.
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
9. IN CASE OF PROBLEMS
Condition
Check Points
No image
• Are the camera and connected equipment turned on?
• Is the mode setting switch DC/AES set to OFF?
Be sure to set to ON.
• Are wires connected correctly?
Unnatural color
• Is the display monitor adjusted correctly?
• Is the lighting too dim?
The image is out of • Is the lens focus adjusted?
focus. • Is the lens or cover dirty?
The image is dark. • Are there any large barrier or bright illumination near the
camera?
• Is the iris of lens adjustment volume correctly set?
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
10. SPECIFICATIONS
1. Image System
Image Device
Pixel Elements
2. Electrical
1/3 inch CCD image sensor
768 (H) x 494 (V)
TV System
2:1 Interlace, 15.734 KHz horizontal, 59.94 Hz
vertical
Horizontal Resolution
S/N Ratio
520 TV lines
50 dB
Minimum Illumination
0.5 lux (More than 10 % of image output,
Smoke cover)
Auto Gain Control (AGC)
Iris Control Mode
Average AGC
Auto Iris Lens
Auto
White Balance
White Balance Range
Gamma compensation
2,500 K to 10,000 K
0.45
Backlight Compensation (BLC) ON / OFF (DIP-SW)
Video Output Signal
VBS (1.0 Vp-p, 75 ohms unbalanced, BNC)
Synchronization System
Line Lock, Internal manually switchable
3. Mechanical
Weight
0.738 lbs (360 g)
Dimension
ø5.08 (D) x 3.94 (H) inches (ø129 (D) x 100 (H)
mm)
4. Optical
Built-in Lens
Varifocal lens
f = 2.8 ~ 10 mm, F 1.3 : Auto Iris
View Angle
Wide : 129 °(D), 100 °(H), 73 °(V)
Tele : 34 °(D), 27 °(H), 20 °(V)
Focus Length
0.3 m ~ ∞
5. Power
+
+
Input Voltage
24V AC 10 % 60 Hz / 12V DC 10 %
-
-
Power Consumption
6. Environmental
3.5 W
Operating Temperature
14 °F to 122 °F (-10 °C to +50 °C), 20 % to
90 % RH
Design and specifications are subject to change without notice.
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
11. EXTERIOR VIEW
1.81 (46)
5.08 (129)
(3.29 (83.5))
5.08 (129)
Dimensions: inch (mm)
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1.81 (46)
depth about 1.58 (40)
Wall
3.94 (100)
Screw ( 0.18 (4)) x4 - TP4 x37
1.81 (46)
Dimensions: inch (mm)
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
CCD SECURITY CAMERA IK-DF02A
The Imaging System Division ("ISD") of Toshiba America Information Systems, Inc. makes the following limited warranties with regard to
this CCD Camera Model IK-DF02A ("Product"). These limited warranties extend to the Original End-User ("You[r]").
Three (3)Year Limited Warranty of Labor and Parts ISD warrants that this Product will perform in accordance with specifications for a
period of three (3) years from the date of purchase by the Original End-User. During this three (3) year period, ISD will repair or replace the
Product, if it does not perform as warranted. In order to take advantage of this Limited Warranty. You must: (a) call (877) 855-1349 to
receive a RMA number: and (b) pay all transportation and insurance charges for shipment of the Product to the ASP or Toshiba Exchange
Center. ISD reserves the right to substitute factory refurbished parts in place of those in need of repair.
Instruction Manual (Owner's Manual): You should read the Instruction Manual (Owner's Manual) thoroughly before operating this
Product. Before seeking warranty service, you should check the troubleshooting guide in the Instruction Manual (Owner's Manual) and
follow the instructions to correct the problem.
How to Obtain Warranty Service Step-by-step Procedures: To obtain warranty service.You should:
1. Contact Toshiba at (877) 855-1349 to first verify operation or installation assistance. (877) 855-1FIX
2. If technical support determines that the unit is defective, an RMA will be issued with return instructions for repair.
3. Securely pack the Product in the original carton and external shipping pack, include a letter explaining the problem with a copy of the
bill of sale or proof of purchase.
4. Prepay all transportation and insurance costs.
Your Responsibilities: This Limited Warranty is subject to the following conditions:
1. You must provide the bill of sale or proof of purchase at the time that warranty service is required.
2. You must notify (877) 855 1349 within (30) days after you discover that the product does not perform in accordance with specifications
during the Limited Warranty period.
3. You must pack the Product in its original carton using the original packing material. Then insert the original carton containing the
Product into another carton with additional packing material before shipping the Product to an ASP or Toshiba Exchange Center.
DISCLAIMERS: ALL OTHER EXPRESS OR IMPLIED WARRANTIES ONTHIS PRODUCT, INCLUDINGTHE IMPLIEDWARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. SOME STATES DO NOT
ALLOWTHE EXCLUSION OF IMPLIEDWARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIEDWARRANTY LASTS. SOTHE
ABOVE LIMITATIONS MAY NOT APPLY TOYOU.
IFTHIS PRODUCT IS NOT IN GOODWORKING ORDER ASWARRANTED ABOVE,YOUR SOLE AND EXCLUSIVE REMEDY SHALL
BE THE REPAIR OF REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ISD OR ITS PARENT COMPANY OR ANY ASP BE
LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT. THIS
LIMITATION APPLIES TO DAMAGES OF ANY KIND, INCLUDING ANY DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST
SAVINGS OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF
CONTRACT,TORT OR OTHERWISE, ORWHETHER ARISING OUT OFTHE USE OF OR INABILITYTO USE SUCH PRODUCT, EVEN
IFTAIS, ITS PARENT COMPANY, OR AN ASP HAS BEEN ADVISED OFTHE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM
BY ANY OTHER PARTY. SOME STATES DO NOT ALLOWTHE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR SOME PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVESYOU SPECIFIC LEGAL RIGHTS, ANDYOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM
STATE TO STATE.
THIS LIMITEDWARRANTY SHALL BEVOID IFTHE PRODUCT OR PARTS HAVE BEEN SUBJECTEDTO MISUSE,ABUSE, ACCIDENT,
IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE INVIOLATION OF ISD'SWRITTEN INSTRUCTIONS, ORWHERE
THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD'S PRIOR AUTHORIZATION, OR UPON THE REMOVAL OR
ALTERATION OF ISD'S FACTORY SERIAL NUMBER. LABOR SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND
ADJUSTMENT OF CONTROLS ARE NOT COVERED BY THIS LIMITED WARRANTY
No person, agent, distributor, dealer, authorized service provider, or company is authorized to change, modify, or extend the terms of this
Limited Warranty in any manner whatsoever.The time within which an action must be commenced to enforce any obligation of ISD arising
under this Limited Warranty or under any statute, or law of the United States or any state thereof, is herby limited to one (1) year from the
date You discovered or should have discovered the problem. This limitation does not apply to implied warranties arising under state law.
Some states do not permit limitation of the time within whichYou may bring an action beyond the limits provided by state law, so the above
provision may not apply to You. This Limited Warranty gives You specific legal rights and You may also have other rights which vary from
state to state.
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
Imaging Systems Division
Download from Www.Somanuals.com. All Manuals Search And Download.
|