Toshiba Projector TLF XD2000 User Manual

OWNER’S MANUAL

3LCD DATA PROJECTOR

TLP-XD2000

Download from Www.Somanuals.com. All Manuals Search And Download.

Before Using

SAFETY PRECAUTIONS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended

to alert the user to the presence of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC.

9740 Irvine Blvd., Irvine, CA 92618-1697 U.S.A

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES

ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.

REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

Phone: (949) 583-3000

WARNING:

USA only

Changes or modifications made to this equipment, not expressly approved by

Toshiba, or parties authorized by Toshiba, could void the user’s authority to

operate the equipment.

WARNING: Handling the cord on this product or cords associated with accessories sold with

this product, will expose you to lead, a chemical known to the State of California

USA only

to cause birth defects or other reproductive harm. Wash hands after handling.

Notice:

CANADA only

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil

numérique de la classe B est conforme à la norme NMB-003 du Canada.

WARNING: This [product] contains mercury. Disposal of mercury may be regulated due to

environmental considerations. For disposal or recycling information, please

contact your local authorities or the Electronic Industries Alliance:www.eiae.org.

USA only

MODEL NAME: TLP-XD2000

TRADE NAME: DATA PROJECTOR

MODEL NAME:TLP-XD2000

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND

INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE

MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE

REFERENCE.

5. Heat

8. Power-Cord Protection

The product should be situated

Power-supply cords should be

routed so that they are not likely to

be walked on or pinched by items

placed upon or against them,

paying particular attention to cords

at plugs, convenience receptacles,

and the point where they exit from

the product.

away from heat sources such as

radiators, heat registers, stoves, or

other products (including

This unit is fully transistorized and does not contain any parts that can be repaired by the

user.

amplifiers) that produce heat.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO

DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL ONLY.

1. Read Owner's Manual

3. Source of Light

After unpacking this product, read

the owner's manual carefully, and

follow all the operating and other

instructions.

Do not look into the lens while the

lamp is on. The strong light from

the lamp may cause damage to

your eyes or sight.

6. Water and Moisture

Do not use this product near water.

- for example, near a bath tub,

wash bowl, kitchen sink, or laundry

tub; in a wet basement; or near a

swimming pool and the like.

9. Overloading

Do not overload wall outlets; to

reduce the risk of electric shock,

do not use the polarized plug with

an extension cord , receptacle, or

other outlet unless the blades can

be inserted completely with three-

wire grounding type to prevent

blade exposure. As this can result

in a risk of fire or electric shock.

2. Power Sources

4. Ventilation

This product should be operated

only from the type of power source

which does not exceed the voltage

range specified on the

rating label and the power cord.

If you are not sure of the type of

power supply to your home,

consult your product dealer or

local power company.

Openings in the cabinet are

7. Cleaning

provided for ventilation and to

ensure reliable operation of the

product and to protect it from

overheating, and these openings

must not be blocked or covered.

The openings should never be

blocked by placing the product on

a bed, sofa, rug or other similar

surface. This product should not

be placed in a built-in installation

such as a bookcase or rack unless

proper ventilation is provided.

Unplug this product from the wall

outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners.

Use a soft cloth for cleaning.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS (Continued)

e) If the product has been dropped or

damaged in any way (If the cabinet

should break, please handle with

care to avoid injury) .

f) When the product exhibits a

distinct change in performance -

this indicates a need for service.

10. Lightning storms

12. Do not place the product

vertically

15. Accessories

For added protection for this

product during storm, or when it is

left unattended and unused for

long periods of time, unplug it from

the wall outlet. This will prevent

damage to the product due to

lightning and power-line surges.

However, while it is thundering or

lightning, do not touch the

apparatus and any connected

cable and/or equipment.

This will prevent you from

receiving the electric shock by an

electric surge.

Do not place this product on an

unstable cart, stand, tripod,

Do not use the product in the

upright position to project the

pictures at the ceiling, or any other

vertical positions. It may fall down

and dangerous.

bracket, or table. The product may

fall, causing serious injury to a

child or adult, and serious damage

to the product. A product and cart

combination should be moved with

care. Quick stops, excessive

force, and uneven surfaces may

cause the product and cart

17. If glass components,

including lens and lamp,

should break, contact your

dealer for repair service.

combination to overturn.

This product incorporates glass

components, including a lens and

a lamp. If such parts should

break, please handle with care to

avoid injury and contact your

dealer for repair service. The

broken pieces of glass may cause

to injury. In the unlikely event of

the lamp rupturing, thoroughly

clean the area around the

13. Stack Inhibited

Do not stack other equipment on

this product or do not place this

product on the other equipment.

Top and bottom plates of this

product develops heat and may

give some undesirable damage to

other unit.

S3125A

16. Damage Requiring Service

Unplug this product from the wall

outlet and refer servicing to

qualified service personnel under

the following conditions:

11. Object and Liquid Entry

projector and discard any edible

items placed in that area.

Never push objects of any kind

into this product through openings

as they may touch dangerous

voltage points or short-out parts

that could result in a fire or electric

shock. Never spill liquid of any

kind on the product.

18. Servicing

a) When the power-supply cord or

plug is damaged.

b) If liquid has been spilled, or

objects have fallen into the

product.

c) If the product has been exposed to

rain or water.

Do not attempt to service this

product yourself as opening or

removing covers may expose you

to dangerous voltage or other

hazards. Refer all servicing to

qualified service personnel.

14. Attachments

d) If the product does not operate

normally by following the operating

instructions. Adjust only those

controls that are covered by the

operating instructions as an

improper adjustment of other

controls may result in damage and

will often require extensive work by

a qualified technician to restore

the product to its normal

Do not use attachments not

recommended by the product

manufacturer as they may cause

hazards.

operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS (Continued)

POWER SUPPLY CORD SELECTION

If your line voltage is 220 to 240V, use one of the following types of cable.

19. Replacement Parts

22. Do not use the product in

a closed installation state.

When replacement parts are

required, be sure the service

technician has used replacement

parts specified by the

manufacturer or have the same

characteristics as the original part.

Unauthorized substitutions may

result in fire, electric shock, or

other hazards.

Plug

Do not place the product in a box

or in any other closed installation

state. Otherwise it may overheat.

This could result in a risk of fire.

configuration Plug type

Line voltage

220 – 240V

configuration Plug type

Line voltage

200 – 240V

Australian

240V

EURO

10A

Switzerland 200 – 240V

240V

220 – 240V

(Replacement of the lamp only

should be made by users.)

Use a 5A fuse which is approved by ASTA

or BSI to BSI362.

Always replace the fuse cover after

changing the fuse.

North American 200 – 240V

240V

15A

20. Safety Check

Upon completion of any service or

repairs to this product, ask the

service technician to perform

safety checks to determine that

the product is in proper operating

condition.

IMPORTANT PRECAUTIONS

Save Original Packing Materials

The original shipping carton and packing materials will come in handy if you ever have to

ship your projector. For maximum protection, repack the set as it was originally packed at

the factory.

Moisture Condensation

Never operate this unit immediately after moving it from a cold location to a warm location.

When the unit is exposed to such a change in temperature, moisture may condense on

the lens and the crucial internal parts. To prevent the unit from possible damage, do not

use the unit for at least 2 hours when there is an extreme or sudden change in tempera-

21. Do not leave thermal-

paper documents or easily

deformed items on top of

the unit or near the air

exhaust for long periods

of time.

ture

Place and Manner of Installation

• Do not place in hot locations, such as near heating equipment. Doing so could cause

malfunction, and shorten the life of the projector.

The heat from the unit could erase

the information on the thermal

paper, or cause deformation or

warping.

• Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts,

shortening their lives, and darkening the screen.

• Do not use this product in the upright position or tilt it up or down by more than 20° from

level. Doing so may cause a failure or shorten the life of the product.

• Using this instrument near a TV or radio may cause interference to the images or audio

sound. If this happens, move it away from the TV or radio.

• Moving the projector from a low-temperature room to a high-temperature room may

cause condensation on the lens or internal parts in the instrument. If you continue to use

it in that situation, the malfunction may result. Ensure to wait until the condensation

naturally disappears.

• In a high altitude location where air is thin, cooling efficiency is reduced so use the

p.41

projector with [Fan mode] set to [High].

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT PRECAUTIONS (Continued)

Avoid Volatile Liquid

Disposal

Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or

plastic products touching the unit for a long time. They will leave marks on the finish.

If cleaning with a chemically saturated cloth, be sure to follow the product's precautions.

This product contains substances which are harmful to humans and the environment.

• The lamp contains mercury.

Please dispose of this product or used lamps in accordance with local regulations.

Following information is only for EU-member states:

LCD Panel

The use of the symbol indicates that this product may not be treated as

household waste. By ensuring this product is disposed of correctly, you will

help prevent potential negative consequences for the environment and

human health, which could otherwise be caused by inappropriate waste

handling of this product. For more detailed information about recycling of this

product, please contact your local city office, your household waste disposal

service or the shop where you purchased the product.

• If the air filter is stained and is clogged up, the main unit inner temperature rises. As a

result, the life of the LCD is shortened and a malfunction may also occur.

Clean the air filter from time to time and replace it regularly. It is recommended that this

replacement be done at the time of replacing a lamp. (Ask a dealer where the unit was

purchased or your nearby service station about an air filter for replacement.)

EXEMPTION CLAUSES

• Toshiba Corporation bears no responsibility in the case of damages arising from natural

disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, acts

by third parties, other accidents, or use under abnormal conditions including erroneous or

improper operation and other problems.

• Toshiba Corporation bears no responsibility for incidental damages (lost profit, work

interruption, corruption or loss of the memory contents, etc.) arising from the use of or the

inability to use this unit.

• Toshiba Corporation accepts no liability whatsoever for any damages arising from not

having followed the descriptions in this Instruction Manual.

Trademarks

• VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of

International Business Machines Corporation.

• Macintosh is a registered trademark of Apple Computer, Inc.

•

Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.

• Adobe is a registered trademark and Acrobat Reader is a trademark of Adobe Systems

Incorporated.

Notational Conventions Used in This Manual

• References to pages with related information are annotated as follows.

p.36

For example, if making a reference to page 36:

• Toshiba Corporation accepts no liability whatsoever for any damages arising from

malfunctions arising from combination with equipment or software that is not related to

Toshiba Corporation.

• The illustrations in this document are for reference purposes only and may not reflect

your package exactly.

REMOTE CONTROL BATTERIES

OTHER CAUTIONS AND INFORMATIONS

Caution

Copyrights

• Never throw batteries into a fire.

Using the batteries improperly may cause them to explode or leak and lead to burn or injury. If

battery-leaking fluid contacts skin, wash the fluid off immediately with clean water and consult a

doctor. If the fluid is spilt on an instrument, avoid contact and wipe it off using tissue paper.

(Dispose of the used tissue paper as flammable garbage after moistening with water.)

Showing or transmitting commercial imaging software or broadcast or cable-broad casting

programs with the purpose of other than the personal and private viewing, including

modifying images using the freeze or resize functions, or displaying with the varying aspect

ratio of the images, could violate the direct or indirect copyrights of the imaging software or

broadcast program, etc., if done without first consulting with the copyright holder. For this

reason, please take appropriate measures before performing one of the actions listed

above, including obtaining a license from the copyright holder.

Notes

• Be sure to use AAA (R03) size batteries.

• Dispose of batteries in a designated disposal area.

• Attention should be drawn to the environmental aspects of battery disposal.

• Do not mix different battery types or combine used batteries with new ones.

• If the remote control does not operate correctly, or if the operating range becomes

reduced, replace both batteries with new ones.

• If the batteries are dead or if you will not be using the remote control for a long time,

remove the batteries to prevent battery acid from leaking into the battery compartment.

In the spaces provided below, record the Model and Serial No. located at the bottom of your

projector.

Model No.

Serial No.

Retain this information for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

Before Using

Others

SAFETY PRECAUTIONS ..................................................................................

IMPORTANT SAFETY INSTRUCTIONS ...........................................................

POWER SUPPLY CORD SELECTION..............................................................

IMPORTANT PRECAUTIONS ...........................................................................

Trouble indications ............................................................................................. 48

Before calling service personnel ........................................................................ 49

Specifications..................................................................................................... 50

List of general specifications .......................................................................... 50

List of supported signals (RGB signals) ......................................................... 51

List of supported signals (Y/P^B/PR signals) .................................................... 52

List of supported signals (Video, S-Video signals) ......................................... 52

Pin assignment of COMPUTER 1 IN, COMPUTER 2 IN &

EXEMPTION CLAUSES .................................................................................... 10

OTHER CAUTIONS AND INFORMATIONS ...................................................... 10

REMOTE CONTROL BATTERIES .................................................................... 11

CONTENTS ....................................................................................................... 12

MONITOR OUT terminals .............................................................................. 52

CONTROL terminal ........................................................................................ 53

Separately sold product.................................................................................. 53

Preparations

Checking the package contents ......................................................................... 14

Names of each part on the main unit................................................................. 15

Names of each part on the control panel and remote control............................ 16

Names of the terminals on the rear panel.......................................................... 18

Preparing and using the remote control............................................................. 19

Placement .......................................................................................................... 20

Connection......................................................................................................... 21

Operations

Turning the power on and off ............................................................................. 23

Basic operations ................................................................................................ 25

Using handy features ......................................................................................... 27

Using auto setting........................................................................................... 27

Correcting the keystone distortion .................................................................. 27

Resizing image ............................................................................................... 28

Cutting off the picture and sound temporarily (Mute) ..................................... 29

Changing picture mode .................................................................................. 29

Changing screen size ..................................................................................... 30

Freezing the image (Freeze) .......................................................................... 30

Setting the password ...................................................................................... 31

Using the menus ................................................................................................ 34

How to use the menus .................................................................................... 34

The image adjustment menu .......................................................................... 35

The display setting menu................................................................................ 37

The default setting menu ................................................................................ 40

Displaying Information (Status display) .......................................................... 42

Maintenance

About lamp......................................................................................................... 43

Lamp replacement ............................................................................................. 44

Air filter cleaning ................................................................................................ 46

Lens and main unit cleaning .............................................................................. 47

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparations

Checking the package contents

Please make sure that the following items are included in the box, along with the main unit.

If any item is missing, please contact the store immediately where you purchased the

product.

Names of each part on the main unit

(4)

(8) (5)(6)

(3) (2)(16)(1)

(1)

(2)

(5)

(6)

(7)

(10) (9)

(7)

(12)

(13) (11) (12)

(14)(15)

(3)

(4)

Back

Front

Name

(1) Infrared remote sensor

(2) Foot adjuster release button : Press to set up or stow the foot adjuster.

: Function

p.19

: Senses commands from the remote control.

p.26

■ (1) Remote control

■ (2) R03 (SIZE AAA) batteries for remote ■ (7) Carrying bag

control (2)

■ (3) CD-ROM

■ (4) Owner’s Manual

■ (5) RGB cable (3m)

■ (6) Power cord ^{(See note)}

(3) Air intake

: Draws in air from outside the projector.

p.16

(4) Control panel

(5) Zooming lever

(6) Focusing ring

(7) Antitheft lock hole

(8) Speaker

: Operates the projector.

p.26

: Adjusts screen size.

p.26

: Adjusts screen focus.

: Attach a safety cable or any other antitheft device.

: Outputs audio sound.

p.18

(9) Terminals on the rear panel : Connects external devices.

Note

(

10) AC IN socket

11) Air exhaust

12) Tilt adjuster

13) Lamp cover

14) Foot adjuster

15) Air filter

: Connect the supplied power cord here.

: Expels air that has grown hot inside the projector.

The shape and number of supplied power cords vary depending on the product destination.

p.26

: Adjusts the projector’s horizontal tilt.

p.44

: Remove to replace lamp.

p.26

: Adjusts the vertical projection angle.

◆The Supplied CD-ROM

: Prevents dirt and garbage from getting into the inside

of the projector.

: Projects expanded image.

The supplied CD-ROM contains an owner’s manual, including information not available for

the printed Owner’s manual (Getting started) and Acrobat^®Reader™ to view the manual.

(

16) Lens

■ Installing Acrobat^®Reader™

(Not necessary if Acrobat^®Reader™ has already been installed in your computer)

Windows^®: Run the CD-ROM, select the Reader/English folder, and run ar500enu.exe.

Follow the on-screen instructions.

Macintosh: Run the CD-ROM, select the Reader/English folder, and run Reader

Installer. Follow the on-screen instructions to install the software.

■ Viewing the manual

Run the CD-ROM and double-click on Start.pdf. Acrobat^®Reader™ launches, and the

menu screen of the Owner’s manual appears. Click on your language. The Owner’s

Manual cover and list of bookmarks appear. Click on a bookmark title to view that

section of the manual. Click on

to view a reference page with related information.

See the Help menu for more information about Acrobat^®Reader™.

Download from Www.Somanuals.com. All Manuals Search And Download.

Names of each part on the control panel and remote control

Name

: Main Function

Control panel

Remote Control

p.27

(

11) AUTO SET button

12) MUTE button

13) FREEZE button

14) Ten-Key button

: Sets up input from computer.

: Cuts off the picture and sound temporarily.

: Pauses image.

: Use when entering password.

p.29

p.30

(12)

(4)

(3)

(7)

Remote

control

button

Remote

control

button

(9) (5) (10)

Input

items

(6)

(11)

(2)

Input items

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[0]

(1)

(2)

(8)

(1)

Deletes one character.

(17)

p.29

p.30

(

15) PICTURE button

16) SCREEN SIZE button

17) RESIZE button

: Changes image mode.

: Changes screen size.

: Enlarges image.

(15)

(16)

(13)

(14)

p.28

(7) (6) (4) (3)

Note

• For the remainder of this manual, buttons are referred to as follows:

Selection buttons %

; ENTER button %

Name

: Main Function

Control panel

(1) ENTER button

(2) MENU button

: Accepts the selected mode.

: Displays menus.

p.34

p.27

(3) KEYSTONE button

(4) ON/STANDBY button

(5) ON/STANDBY indicator

(6) INPUT button

: Adjusts keystone distortion.

p.23

: Turns the power on/off (standby).

: Displays whether power is on or off (standby).

p.23

p.25

: Selects input.

(7) RETURN button

(8) Selection button

: Goes back one screen.

: Menu selections and adjustments, volume control, etc.

p.34

p.48

(9) LAMP indicator

: Informs the abnormality of lamp.

p.48

(

10) TEMP indicator

: Informs the abnormality of internal temperature.

Remote control

(1) ENTER button

(2) MENU button

: Accepts the selected mode.

: Displays menus.

p.34

p.27

(3) KEYSTONE button

(4) ON/STANDBY button

(6) INPUT button

: Adjusts keystone distortion.

p.23

: Turns the power on/off (standby).

p.25

: Selects input.

(7) RETURN button

(8) Selection button

: Goes back one screen.

: Menu selections and adjustments, volume control, etc.

p.34

Download from Www.Somanuals.com. All Manuals Search And Download.

Names of the terminals on the rear panel

Preparing and using the remote control

■ Loading dry-cell batteries

into the remote control

q Remove the battery cover.

■ Operating the remote

control

Point toward the projector’s

(1) (2)

(3) (4)

(6)

(8)

(9)

infrared remote sensor, and press a

button on the remote control.

• Operating the projector from the front

Approx. 15°

Approx. 5m

w Insert the dry-cell batteries.

Be sure to align the plus and minus

ends of the batteries properly.

(5)

(7)

Name

(1) CONTROL terminal

: Main Function

When operating the remote control

from behind the projector, the light is

reflected on the projecting surface

and may travel a shorter distance to

reach the projector depending on the

shape and material of the projecting

surface.

: When operating the projector via a computer, connect

this to the controlling computer’s RS-232C port.

p.53

(2) AUDIO (L/R) terminal

(3) VIDEO terminal

(4) S-VIDEO terminal

(5) AUDIO IN terminal

: Input audio signals from video equipment.

: Input video signals from video equipment.

: Input S video signals from video equipment.

: Input audio signals from a computer, or from video

equipment with a component video signal output

terminal.

e Replace the battery cover.

(6) COMPUTER 1 IN terminal

: Input RGB signal from a computer or other source or a

component video signal (Y/P^B/PR) from video

equipment.

(7) AUDIO OUT terminal

: Outputs audio signals.

(8) COMPUTER 2 IN terminal

(Also used for MONITOR OUT terminal)

: Inputs RGB signal from a computer or other source or

a component video signal (Y/PB/PR) rom video

equipment. It can also be used as MONITOR OUT

terminal by the switch of (9).

: Switches between COMPUTER 2 IN and MONITOR

OUT.

Dry-cell batteries

• Before using the batteries, be sure to observe the Safety Precautions described in

previous pages.

• Remove batteries from remote control when not using for extended periods.

• If the remote control stops working, or if its range decreases, replace all the batteries with

new ones.

(9) Switch

The remote control

• The remote control may fail to operate if the infrared remote sensor is exposed to bright

sunlight or fluorescent lighting.

COMPUTER 2 IN

(Y/PB/PR 2)

/MONITOR OUT

• Do not drop or bang.

• Do not leave in hot or humid locations.

• Do not get wet or place on top of wet objects.

• Do not take apart.

• In rare cases, ambient conditions could impede the operation of the remote control. If this

happens, point the remote control at the main unit again, and repeat the operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Placement

Connection

Placement Styles

As shown in the figures below, this device can be placed in 4 different styles.

Before connection

• Read the owner’s manual of the device you are connecting to the projector.

The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the

Default setting 2 menu, in accordance with your needs.

• Some types of computer cannot be used or connected to this projector.

p.41

p.51

Check for an RGB output terminal, supported signal

• Turn off the power of both devices before connecting.

, etc.

Floor-mounted front projection

Floor-mounted rear projection

• The figure is a sample connection. This does not mean that all of these devices can or

must be connected simultaneously. (Dotted lines mean items can be exchanged.)

Computer

Video recorder,

DVD player, etc.

Computer

(for control)

To audio output

White (L)/Red (R)

Ceiling-mounted front projection

Ceiling-mounted rear projection

To S-video output

RS-232C

terminal

Audio cable

(not supplied)

S-video cable

(not supplied)

To RGB

output

To audio

output

p.53

To RGB

output

To audio output

Audio cable

(not supplied)

Audio cable

(not supplied)

RGB cable

(not supplied)

RGB cable

(supplied)

Control cable

Monitor

WARNING

• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.

Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus

resulting in injury.

• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the

projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.

Improper mounting could cause the projector to fall, resulting in an accident.

• If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let

everyone involved with the use of the projector know that fact.

It is necessary to

switch to MONITOR

OUT by the switch.

p.18

Monitor cable Mini

D-sub 15P-BNC

(not supplied)

Projection Distance and Size

Use the figures, tables, and formulas below to determine the projection size and projection

distance. (Projection sizes are approximate values for full-size picture with no keystone

Audio cable

(not supplied)

To Y/CB/CR output

Green (Y)/Blue

(CB)/Red (CR)

AV cable

(not supplied)

Audio cable

adjustment.)

projection size (inches) – 0.8786

(not supplied)

a (min length) =

a (max length) =

Screen

As seen from above

To audio

output

White (L)/

Red (R)

32.773

Conversion

adapter BNC-pin

(not supplied)

To audio input

White (L)/Red (R)

To video

output

To audio

output

projection size (inches) – 0.7244

27.248

90°

projection distance a (m)

height (H)

projection

size (cm)

Video recorder, etc.

Audio amplifier, etc.

DVD video recorder, etc.

min length

max length

(cm)

(zooming max) (zooming min)

As seen from the side

33 (84)

40 (102)

60 (152)

80 (203)

100 (254)

150 (381)

200 (508)

250 (635)

–

1.19

1.44

2.18

2.91

3.64

5.48

7.31

9.15

–

6.0

7.3

1.19

1.80

2.41

3.02

4.55

6.08

7.60

9.13

Lens center

10.9

14.5

18.1

27.2

36.3

45.4

54.4

90°

a is the distance (m) between the lens and the screen,

and corresponds to a range of 1.19 m to 9.13 m. H is the

300 (762)

height from the image bottom to the center of the lens.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Connection (Continued)

Turning the power on and off

Notes

■ Connecting the power cord

• When COMPUTER 2 IN terminal (also used for MONITOR OUT terminal) is used as

MONITOR OUT terminal, the signal which is input to COMPUTER 1 IN terminal is output.

• Signals are output from MONITOR OUT terminal even in standby mode.

However, from AUDIO OUT terminal, no audio signal is output.

• A computer monitor cannot accept Y/PB/PR signals correctly.

• The AUDIO IN terminal doubles for devices connected to COMPUTER 1 terminal and

COMPUTER 2 terminal.

Insert the power cord connector into

the AC IN socket of the projector.

Insert the power cord plug into a

wall or other power outlet.

The ON/STANDBY indicator will

change to orange, indicating standby

mode.

Power cord connector

(Supplied)

• When an AUDIO OUT terminal is connected, sound is not output from the projector

speaker.

• Output volume of AUDIO OUT terminal can be adjusted by the VOL button.

• Moving pictures played back on computers using DVD software may appear unnatural if it

is projected with this projector, but it is not a malfunction.

■ Removing the lens cover

Be sure to remove the lens cover when the power is

turned on. If it is left on, it could become deformed due

to heat.

■ Turning the power on

Press the ON/STANDBY

button.

Remote

Control

Control panel

Start-up screen

When the beep sound is [On], the

projector beeps, the power turns on,

and the ON/STANDBY indicator lights

in green. After a moment, the start-up

screen appears.

CAUTION

• Do not look into the lens while the lamp is on. The strong light from the lamp may cause

damage to your eyes or sight.

• Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.

• Do not place your hands, face, or other objects near the air exhaust. Doing so could cause

burns, deform/break the object.

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning the power on and off (Continued)

Basic operations

Notes

Turn on the power.

Turn on the power by following the instructions in “Turning the power on”

p.23

• The start-up screen will disappear after a moment.You can dismiss the start-up screen

before this by performing any operation.You can also configure the start-up screen not to

p.37

appear via the Display setting menu

Select the language and the lamp power (When using the

first time).

When the projector is used for the first time after purchase, the start menu for lan-

guage (to display the menus and messages on the screen) and lamp power selection

and configuration is displayed in English. (If the screen is out of focus, adjust it

• The first time you use the projector after purchase, after the start-up screen disappears,

p.25

the start menu is displayed

p.40

• Beep sound can be set not to beep in the Default setting 1 menu

• When [Key lock] is [On], the operation buttons of the projector do not work

• When [Password setting] is [On], then the start-up screen is displayed after the

p.41

according to the step .)

p.31

Password entry screen disappears

q Use the

button to select the

button.

English

French

German

Italian

desired language and press the

Message for setup confirmation is displayed in a

selected language.

■ Turning the power off

Press the ON/STANDBY button.

A message appears on the screen, confirming that you wish to shut off the power. This

message will disappear after a moment. (This operation is no longer valid after the

message disappears.)

Spanish

Then, the menu for lamp power selection and

configuration is displayed. It is automatically set as

Standard.To change the setting, follow the step w.

Portuguese

Russian

Swedish

Turkish

Polish

w Use the

power and press the

The lamp power, if selected, will be toggled without

pressing the button. The display automatically

button to select the lamp

Press the ON/STANDBY button once again.

When the setting of beep sound is [On], the projector beeps, and the screen turns off,

but the internal cooling fan continues to operate. Then, the projector goes into standby

mode.

During cooling, the ON/STANDBY indicator flashes. While the

indicator is flashing, the power can not be turned back on. At this

point of time, it does not matter even if you unplug the power

cord.

Japanese

Chinese (simplified)

Chinese (traditional)

Korean

button.

disappears in a few seconds.

Notes

• When the projector is turned on the next time, the start menu does not appear upon

startup. However, if [Reset all] is executed from the Default setting 2 menu

p.41

the start menu will be displayed the next time when the power is turned on.

p.37

• The language can also be set via the Display setting menu

and Lamp power

Note

p.40

via the Default setting 1 menu

• The projector consumes about 10W of power in standby. We recommend that you unplug

the power cord if you will not be using the projector for an extended period.

• This owner’s manual assumes that English has been selected.

PRECAUTION

Activate the connected device.

Turn on and start the connected device such as a computer.

• If you turn the power on before cooling is complete, give the lamp time (about 5 minutes)

to cool before plugging it back in. If the lamp overheats, it may fail to light.

Press the INPUT button.

An image of the connected equipment is projected.

LCD Panels

LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the

following precautions.

Each time you press the INPUT button, it switches to the input of the connected

equipment that is outputting video signals.

• In order to extend the lifetime of the LCD panel, always turn off the power when not in

use, and make sure that the lamp is off. Keeping the lamp off is also very effective at

saving electricity.

Notes

p.40

• When [Auto input search] is set to [Off] in the Default setting 1 menu

(factory

• If the air filter becomes dirty and clogged, the projector’s internal temperature will rise,

setting is [On]), the Input select menu appears if you press the INPUT button.

• If no signal is being output from the connected equipment, pressing the INPUT button

does not change the input and “There is no other input signal.” will appear.

shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter

p.46

from time to time

, and replace it periodically. Contact the store where you

purchased your projector, or your local Service Station for replacement air filters.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operation (Continued)

Using handy features

Projector placement angle adjustments

The placement angle and the height of the projected image can be adjusted by the foot

adjuster.

■ Using auto setting (Only for input from computer)

Remote

Control

This function sets up the projector to the optimum state such as

sampling phase, frequency, screen position, and clamp for each

type of the input signal by using simple operations.

q Lift up the front of the projector to

the desired angle, then press the

foot adjuster release button.

The foot adjuster extends. Release the

button to lock the position.

Press the remote control’s AUTO SET button.

For computer input, the

icon will appear during processing.

You can set as well by selecting [Auto setting] in the Image

p.35

adjustment menu

w To fine adjust the angle, twist the

foot adjuster.

Notes

e To adjust the horizontal angle, use

• The image may not be projected or auto adjustment/setting may not be performed

p.51 p.52

the right and left tilt adjusters.

correctly for input signals other than those supported by the projector

• If auto setting fails adjustment, adjust manually with [Position] in the Image

• To stow the foot adjuster, hold up the projec-

tor while pressing the foot adjuster release

button, then slowly lower the projector.

p.35

adjustment menu

■ Correcting the keystone distortion

Adjusting the screen size and focus

When the projector placement angle against the

screen is changed while projecting the image,

the picture will undergo keystone (trapezoidal)

distortion.

Use the zooming lever to adjust the screen size.

Remote

Control

Control panel

w Use the focusing ring to adjust the focus.

This projector is capable of correcting this keystone

Adjusting the volume with the

The speaker volume can be adjusted when an audio signal is being input.

buttons

distortion

Before correction After correction

Notes

• Note that lamp characteristics may rarely cause the brightness to fluctuate slightly.

• A lamp is consumable item. If used for extended periods, images will appear dark, and

the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The

lifetime of the lamp depends on conditions of use.)

• The LCD panel is made using extremely advanced technology, but there may be black

spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.

Please note that these are not malfunctions.

Press the KEYSTONE button.

The Keystone menu appears. By default, [Auto v-keystone] is selected.

p.51

• Although this projector supports a wide range of RGB signals

, any resolutions not

Item

Description

supported by this projector (XGA) will be expanded or shrunk, which will affect image

quality slightly. To view high-quality images, it is recommended that the computer’s

external output should be set to XGA resolution.

• With some models of computer having LCD displays or the like, displaying images

simultaneously on the projector and the monitor’s display may prevent the images from

displaying properly. If this happens, turn off the computer’s LCD display. For information

on how to turn off the LCD display, see the owner’s manual of your computer.

• If no signal is being input from the connected equipment or signal input is stopped while

projecting, the “No signal” will appear.

Automatically corrects the vertical distortion.

Auto v-keystone

Press

Screen shrinking at

bottom

Screen shrinking at

top

V-keystone

• If a signal not supported by the projector is input, the “Unsupport signal” will appear.

• If an unavailable operation button is pressed, the

icon will appear.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using handy features (Continued)

Adjusting Keystone distortion [Auto]

Notes

• The

icon appears while resizing.

Press the

button.

• Operating a function other than Mute will release resizing.

• As zooming is processed digitally, the image quality is degraded in larger zoom

ratio.

The keystone distortion is automatically corrected. The

correction.

When adjustment is finished, the Keystone menu appears again. For fine adjust-

icon appears during this

• During resizing or moving the zooming area, the image may be distorted.

ment, select [V-keystone] by the

button and adjust image manually by the

buttons.

■ Cutting off the picture and sound temporarily (Mute)

Remote

Control

When you want to project the images of another projector, overhead

projector, etc. temporarily, this projector’s images and sound can be

turned off.

Adjusting Keystone distortion [Manual]

Select [V-keystone] by the

button.

Use the

buttons for keystone adjustment.

Press the remote control’s MUTE button.

The picture and sound are cut off. (The Mute function is released

when pressing the MUTE button again.)

Note

• Depending on the amount of keystone adjustment and the content of images, some

information may be lost, or the picture quality may suffer.

Notes

• The

icon will appear while mute is in effect.

• Operating any other functions will also cancel the muting.

■ Resizing image

The projected image can be resized (zoomed in/out).

■ Changing picture mode

Press the remote control’s RESIZE

button.

Remote

Control

The projected image mode can be selected.

Each time you press the RESIZE

button, zoom ratio is up.You can keep

Press the remote control’s PICTURE button.

pressing.

The Picture mode menu appears.

1/2/3

Select a mode using

then press

Remote

Control

To zoom out, press the remote control’s RESIZE

button.

Though the button is not pressed, the picture mode

changes as the setting is changed and the display turns off

automatically in a few seconds.

Each time you press the RESIZE

button, zoom ratio is

down.You can keep pressing.

(However, the image cannot be smaller than the original

size.)

Note

• [Picture mode] of the Image adjustment menu has the same

function

p.35

To move the area to zoom in, use the

buttons.

You can keep pressing.

To reset the zoom, press the RETURN button.

The image is reset to the original size.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using handy features (Continued)

■ Changing screen size

■ Setting the password

Remote

Control

The screen size for the projected image can be changed.

How to change password

The default password is 0000.

Press the remote control’s SCREEN SIZE button.

Select [Password] in the Default setting 2 menu and press the

button.

Pressing the button switches Full/Thru/Wide in turn.

Notes

Select [Password registration] in the password registration, setting

menu, and press the button.

• Thru display is available for computer-input images.

• [Screen size] of the Display setting menu has the same function

p.37

The password entry screen is displayed.

• If you use this function on commercial video software, broadcast

or cable-broadcasting except for the purpose of your private

viewing and listening, it may infringe the copyright protected by

the copyright laws.

Enter the current password (4-digit number).

• Enter a 4-digit number for the password using numeric keys of the remote control.

• Enter [0000] (4 zeros) for the first change.

• The password is not displayed. Instead it appears as [****].

Enter a new password (4-digit number).

■ Freezing the image (Freeze)

Remote

Control

The image being projected can be frozen. This function is to be used

to pause a video during a presentation, etc.

Re-enter the same password for confirmation.

Press the remote control’s FREEZE button.

The picture pauses. (The Freeze function is released when

pressing the FREEZE button again.)

Note

• Please do not forget your password. If you forget the password, you can not

release the password by yourself.

In such a case, please inquire your dealer.

Notes

• The

icon will appear while freeze is in effect.

• Other operation will also release the freeze.

• Even if an image is frozen on the projector, the pictures are

running on the video or other equipment.

• If you use this function on commercial video software, broadcast

or cable-broadcasting except for the purpose of your private

viewing and listening, it may infringe the copyright protected by

the copyright laws.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using handy features (Continued)

How to set password (from [Off] to [On])

How to set password (from [On] to [Off])

Select [Password] in the Default setting 2 menu and press the

button.

Select [Password] in the Default setting 2 menu and press the

button.

The password entry screen is displayed.

Select [Password setting] in the password registration, setting menu,

Enter the password using numeric keys of the remote control.

and press the

button.

Select [Password setting] in the password registration, setting menu,

Select [On].

and press the

button.

Select [OK] and press the

button.

Select [OFF].

The password entry screen is displayed.

Enter the password using numeric keys of the remote control.

Select [OK] and press the

Note

button.

The password setting will be set as [On].

How to operate when password is [On]

Turn on the power.

• While the password setting is [On], the password entry screen will be displayed

only when the power is turned on next time.

The lamp lights and the password entry screen appears.

Enter the password using numeric keys of the remote control.

If the entered password is correct, the start-up screen appears and the projector

goes into normal operation. If the password is wrong, a message appears to

prompt you to re-enter the password, and again the password entry screen is

displayed. If you enter a wrong password for more than 5 times, the projector will

automatically power off and enter standby mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the menus

You can call up on-screen menus, and conduct a number of adjustments and settings using

■ The image adjustment menu

Use this menu to set or adjust image-related items. Items that can be set or adjusted are

marked with “Yes”, and those that cannot are marked with “No”. (When an item is masked,

it indicates that you cannot select for the current input.)

p.16

the operation buttons

on the control panel (main unit side) and remote control.

■ How to use the menus

The menu shown below is for operation instructions purposes and might differ from the

actual display.

Item

Description

Computer Y/PB/PR Video S-video

Contrast

Adjust the image contrast.

Yes

Display the Setting display menu.

1. Press the MENU button

2. Select a Category

Lower

Higher

Brightness

Color

Adjust the brightness of the image.

Darker

Brighter

Select a category by using

Displays the current

adjustments and

settings of selected

category.

Item shown with gray

cannot be adjusted with

the current input source.

Adjust the color of the image.

There are following 5 categories:

Lighter

Deeper

p.35

Image adjustment menu

Sharpness

Noise

Adjust the sharpness of the image.

Yes

p.37

p.40

p.41

p.42

Softer

Sharper

Display setting menu

Default setting 1 menu

Default setting 2 menu

Status display menu

Set the function to reduce screen noise.

On (Enable)

reduction

Off (Disable)

Picture mode Press

. Toggle the picture mode with

1/2/3

Yes

R-level

G-level

B-level

Adjust red of the image color.

3. Adjustments & Settings

Press

to open the menu.

Less red

More red

Item

Adjust green of the image color.

These marks

signify that

there are setting

screens. Press

Adjustment/Setting Value

Less green

More green

Adjust blue of the image color.

Less blue

More blue

These marks signify

the items can be

adjusted/set by using

NTSC mode^*2Set the black level with

display a list of

setting screens.

These marks

signify that there

are options.

JAPAN

NTSC (US) mode

NTSC (JAPAN) mode

Press

to display a list of

options.

Auto setting

Position

Automatically adjusts items such as the

samplingphase depending on the type of

input signal.

Yes

* When no item is

changed, press

These marks signify the items can

be selected from the list by using

Press

then change mode using

Yes

and adjust with

After an item is selected, apply it by

Toggle items with

Select items with

Fix selection with

Phase

Adjust to eliminate flicker.

pressing

and press

Frequency

•

The figure shows displays given for operation instructions purposes. As the display may differ depending on the item,

use the following pages as a reference.

Adjust to eliminate periodic patterns and

flickering when many fine vertical lines

appear on the screen.

To return to previous item, press the RETURN button.

H-position

Adjust the horizontal position of the image.

Yes

4. End Press the MENU button.

(The menu disappears about 30 seconds after the last operation.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the menus (Continued)

■ The display setting menu

Item

Description

Computer Y/PB/PR Video S-video

Use this menu to set screen display-related items.

(The items in gray color cannot be set with the current input selection.)

Position

V-position

Adjust the vertical position of the image.

Yes

Clamp 1

Adjusts the clamp pulse position.

Description

Item

Screen size

Clamp 2

Adjusts the clamp pulse width.

(Full): Display with 1024 × 768 dot resolution

(Thru): Display with sampling resolution (for computer input only)

(Wide): Wide-screen display

*1: [Noise reduction] may not work depending on signal type.

*2: [[NTSC mode] can be displayed and adjusted only when the video signal is set to [NTSC] or

Lets the projected image shift vertically when the screen size setting

is wide display (within the range of 1024 × 768).

Up/down

shift

[NTSC4.43]. NTSC mode is set to JAPAN when the language is set to Japanese. It is set to US for

other languages.

Blackboard

mode

When projecting on a non-screen surface, select a color in accordance

with the projecting surface.

Press

and switch with

and

Off/Green/Black/Brown/Blue/Beige

Language

Select one of the languages below to use for displaying the menu and messages

[

English/Français/Deutsch/Italiano/Español/Português/

Svenska/Türkçe/Polski/

Screen to display when there is no input signal

or : Enter setting mode] :Selection]

: Enter setting mode]

[

:Selection]

[Apply:

]

Background

[

[Apply:

Logo/Blue/None

Icon

Display icons as function guides

Off

Start-up screen

User logo

Display start-up screen when power is turned on On

Display a logo customized by the user for the start-up screen or when

there is no input signal.

[

: Enter setting mode]

[

: Selection]

Logo registration

Display style

Background

Press

to display the registration menu.

Black

Blue

White

Logo confirmation Press

Reset logo Yes

Detailed description

[Screen size]

• If “Thru” is selected for [Screen size], portions exceeding the native resolution

(1024 × 768 pixels) will not appear on the screen. Note that for RGB signals with

clock frequency 140MHz or lower, all input pixel signals are sampled. However, if

the clock speed is higher than this, the RGB pixel signal is thinned before

sampling.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the menus (Continued)

Note

Notes

• If you use the screen size setting function on commercial video software,

broadcast or cable-broadcasting programs to display images with the varying

aspect ratio except for the purpose of your private viewing and listening, it may

infringe the copyright protected by the copyright laws.

• You can register a logo from computer input only.

• The area that can be registered is 512 × 384 dots at the center of the screen. To

• Only one logo can be registered. When a new image is registered, the old one is

erased.

• The time needed to register or display the image varies depending on the data size.

• If you use this function on commercial video software, broadcast or cable-

broadcasting except for the purpose of your private viewing and listening, it may

infringe the copyright protected by the copyright laws.

[Up/down shift]

Shifts the projected image vertically when [Screen size] is [Wide].

[Blackboard mode]

Projects the image in colors more like projecting on a screen.

Precaution

• The projected image may differ depending on the type, color, and material of the

blackboard and wall even if the selected color is the same as the projected

Select the size of the registered logo.

: Displays the registered image in original size at center of the screen.

: Displays the registered image by enlarging fully in the screen.

(As processed digitally, the image quality is degraded.)

screen.

[Background]

• TOSHIBA is set for [Logo] by factory setting.

• If user’s logo has been registered, it is displayed when [Logo] is set for

background.

Sets background color when [Center] is selected for the logo [Display style].

[Start-up screen]

If user’s logo has been registered and this setting is [On], the logo is displayed at

start-up.

[User logo]

You can preview the registered logo.

Registers a part of the image that is input from computer, as a stationary picture

and displays it as a logo at start-up and when no signal is input.

You can reset the registered logo, display style and background to the factory

setting. (The logo set for the start-up screen and background is reset.)

How to register user logo

Select [User logo] in the Display setting menu, and press the

or button.

Select <Logo registration> from the displayed menu list and

press the button.

The registration area is displayed for confirmation. Select [OK]

or [Cancel] and press the button.

• If the registered picture does not fall within the display area, operate the

computer to scroll the screen.

Select [Yes] to register and press the

button.

Registration starts.

• A message is displayed while registration is in process.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the menus (Continued)

Default setting 2 menu

■ The default setting menu

This menu shows placement status and other settings.

Item

Description

p.20

Projection

mode

Sets projection mode in accordance with Placement Style.

Default setting 1 menu

(Standard)

(Rear)

(Ceiling)

(Rear ceiling)

Item

Description

Fan mode

Key lock

Sets the cooling fan speed.

Standard

: Select On/Off]

High

No signal

power off

Set the time to wait for the power to be turned off after the last

operation is made with no input signal.

Lock the control panel buttons.

[

: Enter setting mode]

[

Off (not turned off)

30 min.

:Confirm]

[

:Select OK to end]

Set whether the input with signals is only selected or not.

Auto input

Press [Cancel] to return.

Off

Press . (The password and user logo are not reset.)

Resets all adjustments and settings to their factory settings.

Reset all

Beep when operation is made.

Beep

Yes

Sets whether to turn on the power when the ON/STANDBY button is

Power on

pressed (Manual), or when the power cord is plugged in (Auto).

p.31

Password setting

Password

Manual

Auto

Sets the lamp power.

Lamp power

Low

Standard

Detailed description

[Fan mode]

Detailed description

[Auto input search]

Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan

noise gets louder.) Set this option to use the projector, for example, at high altitude

(over 1,500 meters above sea level).

• Do not set Fan mode to [High] when using the projector at a lower altitude.

[Key lock]

Input select menu

Input select

Computer 1

Y/P^B/PR

Computer 2

[On]: Automatically searches the signals that

can be projected, and switches input

from the connected device that outputs

the video signals each time the INPUT

button is pressed. The input from the

connected device that outputs no video

signals is skipped.

Protect from operating errors by locking on the control panel buttons of the

projector. (The remote control operations are available.)

Control panel operations are locked after the setting is done, and accordingly

operation with the control panel buttons is disabled.

• To release the key lock, set the [Key Lock] to [Off] using remote control. Pressing

the [RETURN] button on the projector for 10 seconds also sets the [Key Lock] to

[Off]. (When operating the main unit, the 2 indicators of LAMP and TEMP light in

orange for 3 seconds, and at the same time the projector beeps.)

Y/P^B/PR

Video

S-video

[Off]: Displays the Input select menu.

shows whether signal is

Toggle with

button. (The input without signals can be

selected.)

buttons and press

input or not.

[Power on]

Note that if [Power on] is set to [Auto], then if the power is supplied when restored

after a power outage, the projector will come on.

[Lamp power]

When [Lamp power] is set to [Low], the screen becomes a little darker, but the

cooling fan noise gets quieter.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

Using the menus (Continued)

About lamp

The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure

to fully understand the following characteristics of the lamp and handle it with extreme care.

• The lamp may burst with a loud noise due to impact or deterioration, or fail to light at

the expiration of its life.

• How long it takes before the lamp bursts or the life expires may vary greatly by lamp.

Some may burst shortly after first use.

• Burst is likely to happen if the lamp is used after the replacement period has elapsed.

• When the lamp bursts, the broken pieces of glass may get inside the product or be

released outside from the openings for ventilation.

• When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with

glass dust may be released from the openings for ventilation.

■ Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

“Yes”: displayed, “No”: not displayed

Computer Y/PB/PR Video S-video

Item

Projector

Description

Input

Input source name

Yes

Mode name

Resolution

Frequency

Sync

Signal format

Video mode

Lamp time

RGB input mode ^{[Note 1]}

Resolution (in dots)

Sync frequency

Sync signal polarity ^{[Note 2]}

Y/PB/PR signal format

Color method of video signal

Time of lamp use ^{[Note 3]}

■

Immediately replace the lamp when a sign appears on the screen.

• When the replacement time approaches, a message will appear on the screen.

• The risk of burst will increase if the lamp is continuously used without being replaced.

• Frequently check the used hours and prepare spares when the replacement time

approaches. (Refer to “Status display”. p.42

)

Lamp reset count The count for lamp replacement

Total time

Version

The total time that this projector

is used.

■

When the lamp is broken

Yes

• If glass components, including a lamp and a lens, should break, handle the broken

pieces with care to avoid injury and contact your dealer for repair service.

• In the event of lamp burst, unplug the product from the wall outlet, leave and completely

ventilate the room. Then, thoroughly clean the area around the projector and discard

any edible items placed in that area.

• When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes

or you breathe it.

Firmware version ^{[Note 4]}

Notes

1: The mode of supported RGB signals

2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].

3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as

a counter of guaranteed lamp time.) Please replace the lamp after 2000 hours of use if [Lamp

power] is set to [Standard], or after 3000 hours of use if [Lamp power] is set to [Low], consult

with a dealer about getting replacement for lamp TLPLW11 (sold separately).

4: [Version] shows the version of the projector’s internal control program. This version is referred

to for customer service, etc.

p.51

is shown.

Note

• The displayed information will not be refreshed if the status changes. To refresh the

information, dismiss the display, then display it again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Lamp replacement

A lamp is consumable supplies. If used for extended periods, images will appear dark, and

the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime

Mount the new lamp.

Align the orientation, press down the new lamp

until the bottom is reached, and lock in place using

the three lamp locking screws.

of the lamp depends on condition of use.) If this happens, replace it with a new one

WARNING

•

If the projector is mounted on the ceiling, it is recommended to use your Toshiba dealer-

ship when the lamp has to be exchanged.

Uncovering the lamp while the projector is mounted on a ceiling may lead to a danger

of damage from falling pieces of glass if the lamp is broken. Besides, working at high

elevations can also be hazardous. Do not attempt to replace the lamp by yourself.

Replace the lamp cover.

Align the cover, and press it in, then tighten the

screws loosened in step

no longer loose.

until the lamp cover is

• When replacement is required, be sure to use TLPLW11 (sold separately).

Reset the lamp time.

See the lamp’s manual for instructions on resetting

the lamp time.

CAUTION

• If you have been using the projector, the lamp will be very hot, and may cause burn

injuries. Wait for the lamp to cool (for longer than 1 hour) before replacing it.

• If the lamp should break, please handle with care to avoid injury due to broken pieces

p.43

(

) and contact your dealer for repair service.

Notes and Precautions

• The [Lamp time] item in the Status display menu indicates the time of lamp use (as a

p.42

rough guide)

• Please replace the lamp after 2000 hours of use with [Lamp power] in the Default

setting 1 menu set to [Standard], and 3000 hours of use with [Lamp power] in the

Unplug power cord.

p.40

Default setting 1 menu set to [Low].

Wait until lamp is sufficiently cooled.

Wait for at least 1 hour.

• There are cases that the lamp can not work before the above mentioned period expires

or before the replacement message is displayed.

• Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the

projector may fail to be powered on or the lamp may fail to come on.

• Always replace the lamp with a new one.

• The lamp is made out of glass. Do not touch the glass surface with your bare hands,

bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)

Remove the lamp cover.

Lamp cover

Loosen the two screws, raise the lamp cover

with your fingers as shown to remove the lamp

cover. Use care to avoid any damage to nails

and/or tip of your finger(s). If you have any

difficulty in removal, you can use a screwdriver

or any other smaller tool for your convenience.

About lamp replacement messages

• The lamp replacement message of this projector displays an appropriate period

according to the use period for [Standard] / [Low] of the [Lamp power] respectively.

• When the replacement time approaches, the message of “The lamp life is ending.

Please change the lamp.” and the icon

are displayed every time the power is

turned on. This display disappears when you press the

button.

Pull out the lamp.

Loosen the three lamp locking screws, pull up the

handle, and remove the lamp.

Used Lamps

This projector’s lamps contain trace amounts of environmentally harmful inorganic

mercury. Be careful not to break used lamps, and dispose of them in accordance with

local regulations.

Download from Www.Somanuals.com. All Manuals Search And Download.

Air filter cleaning

Lens and main unit cleaning

The air filter prevents dust and debris from getting inside the projector. Never run the

projector with the filter removed. It is recommended that the air filter is cleaned regularly.

• The message “Check the air filter for dirt.” is displayed every 100 hours. (If the usage time

exceeds 100 hours, this message is displayed for about 30 seconds when the image is

displayed for the first time after power is turned on. This display will be dismissed with any

operation.)

WARNING

•

Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership

Attempting to clean/replace the lamp at a high site by yourself may cause you to fall

down, thus resulting in injury.

■ Lens cleaning

• Check out the filter and any debris is found, use the following procedure for cleaning.

• Clean the lens with a commercially available blower and/or

lens cleaner.

WARNING

• The lens is easily scratched, so do not rub it with hard objects,

or strike it.

• Request cleaning and maintenance of a ceiling-mounted unit from your projector

dealership.

■ Main unit cleaning

Unplug power cord.

Remove the air filter.

Pull out the air filter by taking the catch shown in

the figure.

• Clean the main unit after unplugging the power cord.

• Wipe dirt off the main unit gently with a soft cloth.

• Do not wipe the main unit with a damp cloth. Doing

so may allow water to get inside, resulting in an

electric shock or failure.

• Do not use benzene, thinner and the like as they may

deform or discolor the unit or damage the paint

surface.

• When using a chemically treated cloth, follow the

precautions included with the cloth.

Clean the filter.

Carefully remove the dust and dirt from the air filter

with a vacuum cleaner or the like.

Replace the air filter.

Notes

• Allowing dirt and dust to build up in the air filter will worsen the air circulation inside the

projector, causing the internal temperature to rise, causing the projector to stop working

or malfunction.

• Insert the air filter all the way in. Leaving gaps will allow dust and dirt to get inside the

projector again.

• If you wash the air filer with water, make sure to dry it completely before replacing it.

• If the air filter is torn, consult with your dealer about replacing it with a new one.

Continuing to use a ripped filter will allow dust and dirt to get inside the projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Before calling service personnel

Trouble indications

If you think something is wrong, check the followings before contacting customer service.

The indicator lights to inform you of internal abnormalities.

p.48

Please see “Trouble indications”

as well.

No power

% Problem with projector

If This Happens

Check

(Off)

• Unplug the power cord, and contact your dealer.

• Is the power cord plugged in? Is it connected to the projector?

• Is the lamp cover attached properly?

No power

p.45

Lamp went out during use, or won’t come on

% Lamp temperature is high so that it is difficult to turn on, the lifetime of the

lamp has ended or the projector is malfunctioning.

• Unplug the power cord and wait for a short while, then turn the power

back on.

p.48

• Is the ambient temperature high?

Power goes out

during use

(Red (Red lit)

p.48

• Is the air intake or air exhaust blocked?

flashing)

p.25

• Is the projector turned on? (When [Auto input search] is [Off])

No picture

p.29

• Is the mute function on?

• If a lamp burns out, replace it with a new one.

❈ The abnormal display will not disappear until the power cord is

unplugged.

(Red lit) (Red lit)

p.35

p.21

• Is the brightness setting minimized?

• Are the connections set up correctly?

• Are all the connected devices functioning properly?

You can not turn on the power during abnormal display.

p.29

Power went out during use

• Is the mute function on?

No audio

p.26

% Internal overheating, or the outside temperature is too high.

• Place the projector so that the air intake and exhaust are not blocked.

• Unplug the power cord and wait for a short while, then turn the power

back on.

• Is the volume setting minimized?

(Red lit) (Red

flashing)

p.21

• Are the connections set up correctly?

• Are all the connected devices functioning properly?

p.51 p.52

• Is the input signal supported by the projector?

• Is there something generating an abnormal video signal, for

instance the video tape?

Picture not

displayed

correctly

❈ The

icon will appear before the power goes out.

❈ The abnormal display will not disappear until the power cord is

unplugged.

You can not turn on the power during abnormal display.

p.47

• Is the lens dirty?

Picture blurred

Part of picture

out of focus

p.26

• Is the lens focus adjusted optimally?

Power went out during use

% Problem with internal cooling fan.

p.20

•

Is the projection distance within the projector’s supported range?

• Is the projector’s screen placement angle tilted too far?

• Are the sharpness or sampling phase adjustments off?

p.20

(Red lit) (Green

flashing)

• Unplug the power cord, and contact your dealer.

p.35

❈ The

icon will appear before the power goes out.

❈ The abnormal display will not disappear until the power cord is

unplugged.

You can not turn on the power during abnormal display.

p.35

• Are the brightness or contrast adjustments off?

• Is the lamp nearing the end of its service life?

Image is dark

p.42

p.35

• Are the color, R-level, G-level, or B-level adjustments off?

• Is the screen dirty?

Colors too light

Bad shading

Power went out during use, or power won’t come on

% The lamp cover is not properly attached.

p.37

• Is the blackboard mode set properly?

• Is the lamp nearing the end of its service life?

(Orange (Red lit)

flashing)

p.45

• Unplug the power cord, and reattach the lamp cover.

p.42

❈ The abnormal display will not disappear until the power cord is

unplugged.

You can not turn on the power during abnormal display.

p.41

• Is the key lock function on?

Control panel

key doesn’t work

Power went out during use

% Problem inside the projector.

• Are the remote control’s batteries drained?

• Are the batteries inserted into the remote control correctly?

• Is the remote control being used within the effective range?

Remote control

doesn’t work

p.19

(Red lit) (Orange

lit)

• Unplug the power cord and wait for a short while, then turn the power

back on.

• If the above action will not clear the problem, unplug the power cord,

and contact your dealer.

p.19

•

Are there any obstructions between the remote control and projector?

• Are there any fluorescent or other bright lights shining at the

projector’s infrared remote sensor?

❈ The

icon will appear before the power goes out.

❈ The abnormal display will not disappear until the power cord is

unplugged.

You can not turn on the power during abnormal display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

■ List of general specifications

■ List of supported signals (RGB signals)

This projector supports the following RGB signals. Note, however, that depending on the

computer model, the screen may show flicker or streaking. Please adjust the projector if

this happens.

Item

Specification

Consumption Power

Weight

280 W

2.8 kg

External Dimensions

(including protruding parts)

Cabinet material

288 × 92 × 247 mm (W × H × D)

Refresh rate

(Hz)

H-frequency

(kHz)

Clock

(MHz)

Resolution

Mode

PC resin and PC+ABS resin

720 x 400

640 x 480

720x400_85

VGA_60

VGA_72

VGA_75

VGA_85

SVGA_56

SVGA_60

SVGA_72

SVGA_75

SVGA_85

MAC16"

85.039

59.940

72.809

75.000

85.008

56.250

60.317

72.188

75.000

85.061

74.550

60.004

70.069

75.029

84.997

74.700

75.000

60.000

85.002

60.020

75.025

85.024

59.978

60.000

65.000

70.000

75.000

85.000

37.927

31.469

37.861

37.500

43.269

35.156

37.879

48.077

46.875

53.674

49.725

48.363

56.476

60.023

68.667

60.134

67.500

60.000

85.938

63.981

79.976

91.146

65.317

75.000

81.250

87.500

93.750

106.250

35.500

25.175

31.500

36.000

40.000

50.000

49.500

56.250

57.283

65.000

75.000

78.750

94.500

79.857

108.000

148.500

108.000

135.000

157.500

121.750

162.000

175.500

189.000

202.500

229.500

Conditions for usage environment Temp: 5°C to 35°C; relative humidity: 30% to 70%

Display method 3-panel transmission

Panel size

Drive system

0.6 type

TFT active matrix

LCD Panel

Picture elements 786,432 pixels (1024H × 768V)

800 x 600

Lens

Lamp

Zoom lens

F=1.6-1.88 f=18.6-22.3 mm

High-pressure mercury lamp (180 W)

33-300 inches

1.19-9.13 m

1W (Mono)

Mini D sub 15 pin RGB / Y/PB/PR (dual use)

Projection screen size

Projection distance

Speaker

COMPUTER 1

IN terminal

COMPUTER 2

IN terminal

S-VIDEO terminal

AUDIO (L/R) terminal

VIDEO terminal

AUDIO IN terminal

AUDIO OUT terminal

CONTROL terminal

832 x 624

1024 x 768

XGA_60

XGA_70

XGA_75

XGA_85

Mini D sub 15 pin RGB / Y/PB/PR / MONITOR OUT (dual use)

Mini DIN 4 pin

RCA Pin Jack × 2

RCA Pin Jack

3.5mm dia. stereo mini-jack

Mini DIN 8 pin (RS-232C)

MAC19"

1152 x 864

1280 x 960

SXGA1_75

QuadVGA_60

QuadVGA_85

SXGA3_60

SXGA3_75

SXGA3_85

SXGA+

UXGA_60

UXGA_65

UXGA_70

UXGA_75

UXGA_85

1280 x 1024

Notes

1400 x 1050

1600 x 1200

• This model complies with the above specifications.

• Designs and specifications are subject to change without notice.

• This model may not be compatible with features and/or specifications that may be added

in the future.

Note

• Signals whose resolution exceeds the native resolution (1024 × 768 pixels) will be

compressed. For this reason, some information may be lost, or image quality may be

affected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications (Continued)

■ List of supported signals (Y/PB/PR signals)

■ CONTROL terminal

● Pin assignment

Signal format

fh(kHz)

15.73

31.47

15.63

31.25

45.00

37.50

33.75

28.13

fv(Hz)

59.94

50.00

60.00

50.00

60.00

50.00

480i(525i)@60Hz

480p(525p)@60Hz

576i(625i)@50Hz

576p(625p)@50Hz

720p(750p)@60Hz

720p(750p)@50Hz

1080i(1125i)@60Hz

1080i(1125i)@50Hz

Pin No.

Signal Name

RXD

Description

Receiving data

Consent to send

Data set ready

Signal ground

Request to send

No connection

Sending data

CTS

DSR

GND

RTS

N.C

TXD

GND

Signal ground

Mini DIN 8 pin connector

■ List of supported signals (Video, S-Video signals)

● Interface format

Video mode

NTSC

fh(kHz)

15.73

15.63

15.73

15.63

15.73

fv(Hz)

fsc(MHz)

3.58

1 Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;

Stop Bit Length: 1 bit

STX (02h) Command (3Byte) ETX (03h)

Only 1 command valid per communication.

For input commands, only ASCII-compliant all-uppercase

alphanumeric characters supported.

PAL

4.43

2 Communication format

3 Data format

SECAM

PAL-M

4.25 or 4.41

3.58

PAL-N

3.58

PAL-60

NTSC4.43

4.43

4 Replies

Acknowledge

ACK (06h) CR (0Dh) Data ... Normally ended

4.43

ACK (06h) ESC (1Bh)

NAK (15h)

... Aborted

No acknowledge

■ Pin assignment of COMPUTER 1 IN, COMPUTER 2 IN &

If commands are to be sent consecutively, wait for the response from the projector

before sending the next command.

MONITOR OUT terminals

No.

Pin description

During Y/PB/PR input

● Main Commands

During RGB input

Video signal (R)

Video signal (G)

Video signal (B)

GND

Item

Command

PON

Color difference signal (PR

)

Power on

Power off

Icon display on

Luminance signal (Y)

POF

MO0

MO1

PAT

DON

DOF

Color difference signal (PB)

Icon display off

GND

Auto setting (RGB input)

Status display on

Status display off

GND (R)

GND (PR

)

Mini D sub 15 Pin connector

GND (G)

GND (Y)

Input Signal

• RGB input

RGB signals:

Horizontal sync signal: TTL level (Pos/neg polarity)

Vertical sync signal: TTL level (Pos/neg polarity)

• Y/P^B/PR input

GND (B)

GND (PB)

Note

N.C

0.7V (p-p) 75 ꢀ

GND

• Contact your dealer for control cable and other commands.

GND

N.C

■ Separately sold product

Horizontal sync signal

Vertical sync signal

N.C

Y signal:

P^B/PR signals:

1.0V (p-p) 75 ꢀ

0.7V (p-p) 75 ꢀ

Replacement Lamp

Model TLPLW11

7 Do not connect anything.

Download from Www.Somanuals.com. All Manuals Search And Download.

TechniSat DVD Player TechniBox VIACAM User Manual
Toshiba Flat Panel Television 15DL75 User Manual
Tripp Lite Surge Protector PM6SN1 User Manual
Ultra Products Personal Computer m923 User Manual
Vanguard Managed Solutions Electric Heater FB32NCA User Manual
Verilux Indoor Furnishings VD12 User Manual
ViewSonic Projector PROJ27995 1W User Manual
Vision Fitness Bicycle ST770 User Manual
Vulcan Hart Kitchen Grill RRE60 User Manual
Weed Eater Lawn Mower WET1338B User Manual