Toshiba Projection Television TV GEN 03 User Manual

TOSHIBA AMERICA CONSUMER PRODUCTS, INC.

NATIONAL SERVICE DIVISION

1420-B TOSHIBA DR.

LEBANON, TN 37087

TECHNICAL TRAINING

TV-GEN-03

Subject:

Product:

Chassis:

Digital Convergence Alignment

PROJECTION TELEVISION, Rear CRT

All Toshiba rear CRT projection televisions with digital convergence

Model Year: All

Models: All

Prerequisites:

None

Purpose:

Upon completion of this Training Module, the technician will be able to properly

converge a Toshiba CRT-based rear projection television set. Using the correct digital

convergence alignment procedures will enable the technician to identify symptoms

requiring more in-depth troubleshooting.

These skills will help improve servicing picture quality issues.

Objectives:

While performing a convergence alignment, specify when and when not to reload

convergence backup data 100% of the time.

Following a written procedure, correctly reload the convergence backup data

from the DCU memory.

Given the TV model number and picture size, identify the correct convergence

overlay and grid 100% of the time.

Following a written procedure, and using the correct overlay(s), align the

convergence to factory specifications.

While performing a convergence alignment, identify visual symptoms which

indicate further troubleshooting is required, at least 80% of the time.

Product Specific Service Manuals:

This training is designed as an aid to the technician in servicing Toshiba products. It is not a

replacement for the appropriate service manual(s). Toshiba service manuals contain product and

model specific information and must be consulted prior to servicing any product.

Product Safety Precautions:

Product Safety Precautions are described in the Toshiba service manual(s) for products and models

covered in this training. All safety precautions and checks must be complied with before returning any

product to the customer. Servicers who defeat safety features or fail to perform safety checks may be

liable for any resulting damages and may expose themselves and others to possible injury.

2002 Toshiba America Consumer Products, Inc.

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

When using an overlay kit, it is important to know the type of unit it is designed for use

with and the kit part number. The availability and part numbers of the overlay kits are

subject to change as screen sizes are added or discontinued. Table 1 details the

currently available overlay kit part numbers.

Part

Screen Aspect Picture Model

Number

Size

40”

42”

43”

48”

50”

53”

55”

56”

57”

61”

65”

71”

Ratio

16:9

4:3

16:9

4:3

16:9

4:3

16:9

4:3

Size

All

Full

All

N/A

All

Full

All

Full

All

Year

All

2002+

All

2002+

All

PSOL40X1

PSOL42W1

PSOL43X1

PSOL4801

PSOL50X1

PSOL50W1

PSOL53X1

PSOL55X1

PSOL56X1

PSOL57W1

PSOL61X1

PSOL65X1

PSOL7101

All

2002+

All

N/A

All

Table 1

Each kit part number begins with the acronym PSOL, meaning Protective Screen Over

Lay. Following the acronym are a series of alpha-numeric characters identifying the

screen size and intended unit type. In Example 1, “40” identifies the kit for use with a 40

inch screen size. “X1” indicates the kit contains all grids for any unit in that screen size.

Example 1: PSOL40X1

In some cases there are models with different aspect ratios within a screen size

category. In such cases, the letter “W” in the kit part number indicates use with wide

screen (16:9 aspect ratio) units. See Example 2 for details:

Example 2

PSOL50X1 is used with any 50 inch unit with a 4:3 aspect ratio screen.

PSOL50W1 is used with any 50 inch unit with a 16:9 aspect ratio screen.

Readme: The overlay dimensions are contained in the appropriate unit Service

Manual, as shown in Figure 1. If a particular overlay kit is not available, or there

is an urgent need for a complete convergence alignment before the kit can be

delivered, strings and low-tack tape can be used to achieve the desired results.

Module No. TV-GEN-03

Page 2 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Figure 1

And then… Accessing Service Mode:

Once the correct overlay is placed on the screen, the unit must be put into Service

Mode before any alignment adjustments are made. There are currently two methods of

Service Mode entry, dependant upon the model and type of set. The methods are

described as follows:

1. All digital convergence equipped units built prior to 2001 and all interlaced

scan units:

a. With the unit powered “ON”, press and release the MUTE key on the

remote control.

b. Press the MUTE key a second time and hold.

c. While holding the MUTE key, press the MENU key on the front panel.

A pale blue “S” will appear in the upper right corner of the screen, as

shown in Figure 2.

d. Press the MENU key on the front panel a second time. RCUT will

appear in the upper left corner of the screen.

Figure 2

Module No. TV-GEN-03

Page 3 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Readme: RCUT is a data address in the system EEPROM. The hexadecimal

data contained in the address will be shown just below it, as shown in Figure 3.

Figure 3

2. All progressive scan units built from 2001 forward:

a. With the unit powered “ON”, press and release the MUTE key on the

remote control two times.

b. Press the MUTE key a third time and hold.

c. While holding the MUTE key, press the MENU key on the front panel.

A pale blue “S” will appear in the upper right corner of the screen.

d. Press the MENU key on the front panel a second time. RCUT will

appear in the upper left corner of the screen.

Readme: Important parameters of the set can be accessed and adjusted from

Service Mode. Use caution whenever working in this area.

The rubber meets the road - Convergence Alignment:

Readme: Always allow the set to warm up for at least 15 minutes before making

any adjustments.

Convergence alignment instructions vary according to the unit type. The instructions

assume a worst-case scenario, such as replacing all three CRTs or the digital

convergence board, and the use of an overlay kit. All versions of the instructions are

included as Appendices A through C of this document.

Readme: If the set requires only minor convergence adjustments, enter the

procedure where you feel it is necessary.

1. Optical and electrical focus

a. Remove or raise the screen to gain access to the CRTs.

b. Reverse the lenses if necessary.

c. Enter the convergence alignment service mode.

d. Optically and electrically focus each CRT.

2. Mechanical tilt

a. Check each CRTs tilt.

b. Adjust if necessary.

c. Store the data.

Module No. TV-GEN-03

Page 4 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

3. User convergence and magnetic centering

a. Disconnect any input to Video 1.

b. Enter the user convergence area.

c. Vertically and horizontally center all 3 colors in all adjustable areas.

d. Exit the user convergence area.

e. Enter the convergence alignment service mode.

f. Mechanically center all 3 colors.

i. Stretch 2 pieces of string diagonally across the screen

ii. Rotate the centering rings on each CRTs neck

g. Lock the centering rings with adhesive.

h. Exit the service mode.

4. Electrical centering

a. Use a signal generator.

i. Crosshatch pattern

b. Enter service mode.

c. Adjust HPOS to center horizontally.

d. Adjust VPOS to center vertically.

5. Green geometry

a. Enter the convergence alignment service mode.

b. Secure the appropriate overlay to the screen.

c. Adjust the green geometry to match the overlay.

i. Start in the center of the screen

ii. Work clockwise around the screen

6. Red convergence

a. Align to green.

7. Blue convergence

a. Align to green.

8. HD convergence

a. Progressive scan 4:3 units only.

b. Component video signal to HD 1 input.

c. 1080i picture on or HD image shape compressed.

9. White balance

a. Set white balance according to the appropriate Service Manual.

b. Check picture quality using a live video signal.

10.Width, height, and vertical linearity

a. Adjust if the memory IC (QA02) has been replaced.

b. Adjust if the crosshatch pattern is not reasonably close to the overlay

pattern.

Readme: The convergence alignment may not be complete at this point.

Depending on the year of production and the type of unit being adjusted, there

could be several different picture size modes that require adjustment.

Module No. TV-GEN-03

Page 5 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

End of the line? Specifications

Once all conceivable picture size modes have been aligned, verify the convergence

meets factory specifications. The specifications listed in Table 2 reflect the maximum

allowable misconvergence, in any direction, referencing either red or blue to green.

Screen

Size

Zone

0.5mm 3.5mm 2.5mm 3.5mm 2mm

0.5mm 3.5mm 2.5mm 3.5mm 2.5mm 3.5mm 2.5mm 3.5mm 2.5mm

3.5mm 2.5mm 3.5mm 2mm

0.5mm 4mm

3mm

4mm

3mm

4mm

3mm

4mm

3mm

50 (4:3) 0.5mm 4mm

50(16:9) 0.5mm 3.8mm 2.7mm 3.8mm 2.3mm 3.8mm 2.7mm 3.8mm 2.3mm

0.5mm 4.5mm 3.2mm 4.5mm 3.2mm 4.5mm 3.2mm 4.5mm 3.2mm

0.5mm 4.5mm 3mm

4.5mm 2.5mm 4.5mm 3mm

4.5mm 2.5mm

0.5mm 5mm

3.5mm 5mm

3mm

5mm

3.5mm 5mm

3mm

Table 2

Zones A through J are the areas of the screen referenced by the specifications. The

zones are illustrated in Figure 4.

H Q J K B

G P A L C

F N E M D

Figure 4

If the convergence cannot be aligned to factory specifications, further troubleshooting is

required.

Don’t Worry:

Beginning with the 2002 production year, HD Compatible units include a service feature

that allows a qualified technician to restore factory convergence data from a back-up

memory location.

Module No. TV-GEN-03

Page 6 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Readme: Backup data should be loaded only if corruption of the original data

is suspected or if the set is severely misconverged. Minor misconvergence

issues should be corrected by performing the appropriate alignment procedure.

To load back up data:

1. Enter Service Mode as described in the appropriate Service Manual.

2. Enter convergence alignment mode by pressing the “7” key on the remote.

3. Display vertical stripes by pressing the “9” key on the remote.

4. Load the backup by pressing the “1” key on the remote.

a. The following message will appear on screen for:

ENTER: TO LOAD BACKUP DATA

EXIT: TO EXIT

5. Press the “ENTER” key on the remote, as shown in Figure 5, to load the backup

data.

a. The displayed net pattern will misconverge briefly, then return to a normal

state.

Figure 5

6. Following the alignment procedure in the service manual, make any necessary

convergence adjustments.

7. Write the new data to convergence memory by pressing the “7” key on the

remote one time.

8. Press the “Touch Focus” key on the front panel of the unit.

a. The Touch Focus pattern will scroll across the screen two times. Once

quickly, then slowly.

9. “CALIBRATION FINISHED” will display on screen and the unit will exit to service

mode.

a. The new convergence data is saved to memory and new backup data is

created.

10.Power the unit off to exit service mode.

Module No. TV-GEN-03

Page 7 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Readme: Do not attempt to load backup data if the digital convergence PCB has

been replaced. Backup data in the new PCB memory is not created until

convergence has been adjusted and the CALIBRATION procedure has been

completed.

Something to think about:

It is important to know when a convergence alignment will not correct the unit problem.

If after following the correct procedure, the convergence cannot be aligned to factory

specifications, further troubleshooting is required. Table 3 lists a few of the many

possible symptoms.

Repeated Touch Focus errors

Intermittent loss of convergence

Repeated convergence drift of any color

Selected color will not adjust in either direction

Convergence crosshatch pattern will not display

Convergence crosshatch pattern is severely distorted

Touch Focus pattern is not displayed

Touch Focus pattern is severely distorted

Back up data will not load

Cannot enter Service Mode

Data cannot be saved after alignment

Table 3

Points to remember:

Familiarity and practice help the technician develop confidence in performing a digital

convergence alignment or determining the need for further troubleshooting. Having the

knowledge and necessary tools available are an important first step in the process of

gaining experience. While taking this first step, it is best to follow the alignment

instructions carefully and exactly. Back up data, if available, is a useful tool if problems

occur. It can provide a good starting point in certain cases, but it should not be viewed

as a “cure-all” for convergence problems. In most cases, only minor adjustments will be

necessary. Focus and centering adjustments will not be needed and the procedure can

begin in the GEOMETRY stage. Minor adjustments made in this way do not require

the use of back up data or an overlay kit. Simply make the needed adjustments, save

the new data accordingly, exit the service mode, and you’re outta there!

Module No. TV-GEN-03

Page 8 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Appendix A

Interlaced Scan Units with 4:3 Aspect Ratio

Section 1: OPTICAL & ELECTRICAL FOCUS

1. Follow the appropriate disassembly instructions to gain access to the CRTs.

2. If the wing nuts on the lenses are pointed toward the screen, reverse the lenses

on each tube so the wing nuts are facing the back of the set. Leave the lenses in

this position after servicing. Put the screen assembly back on.

3. From the Service Mode press the 7 key on the remote control to display the

convergence crosshatch pattern.

4. Push the 100 key to turn off the red tube, and the CH RTN/ENT key to turn off

the blue tube.

5. Position a mirror for viewing the screen from the rear of the set. From the rear of

the set, loosen the wing nut on the green lens, and adjust the lens for the best

focus in the center area of the screen.

6. From the front of the set, adjust the electrical focus control for best focus in the

center of the screen.

7. Repeat the optical focus, and then tighten the wing nut.

8. Repeat the electrical focus.

9. Push the 100 key to turn on the red tube, and the 0 key to turn off the green tube.

10. Adjust the red optical and electrical focus in the same manner.

11. Push the CH RTN/ENT key to turn on the blue tube, and the 100 key to turn off

the red tube.

12. Adjust the blue optical and electrical focus in the same manner. Electrically

defocus the blue slightly, to maintain uniform brightness.

Section 2: MECHANICAL TILT ADJUSTMENT

1. With the set still in convergence mode, and the convergence overlay on the

screen, check each CRT’s tilt. If a CRT’s pattern is tilted, loosen the appropriate

yoke with a non-magnetic screwdriver. Rotate the yoke until the pattern is

aligned vertically and horizontally. Re-tighten the yoke.

2. Press the 7 key on the remote to store the convergence data.

3. After the data is stored, press the 7 key on the remote again to exit the

convergence crosshatch pattern.

4. The unit will return to service mode and display a normal picture with the letter

“S” in the upper right corner.

5. Power the unit OFF to exit service mode.

Section 3: USER CONVERGENCE AND MAGNETIC CENTERING ADJUSTMENTS

1. Disconnect any source at the Video 1 input.

2. Turn the power on.

3. Enter the user convergence screen through the customer menu.

4. Move the red vertical cross hair as far as it will go to the right. Note the location.

Move the red vertical cross hair as far as it will go to the left. Note that location.

Set the red vertical cross hair to the center of the two extremes.

Module No. TV-GEN-03

Page 9 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Appendix A

5. Move the red horizontal cross hair as far as it will go toward the top of the screen.

Note the location. Move the red horizontal cross hair as far as it will go toward the

bottom of the screen. Note that location. Set the red horizontal cross hair to the

center of the two extremes.

6. Repeat steps 4 and 5 for the blue cross hair.

7. Repeat steps 4, 5, and 6 for all user convergence adjustment points.

8. Exit the customer convergence screen.

9. Enter the service adjustment mode.

10.Enter the service convergence adjustment mode to display the crosshatch pattern.

11.Push the 100 key to turn off the red tube, and the CH RTN/ENT key to turn off the

blue tube.

12.Rotate the centering rings on the green CRT to center the green cross bar. If the

rings won't turn, remove the locking glue with a small knife. Use the center cross

hairs of the convergence overlay, or two pieces of string stretched diagonally

across the screen to locate the center of the screen.

13.Push the 100 key to turn on the red tube, and the CH RTN/ENT key to turn on the

blue tube.

14.Center the red and blue crossbars, using the green crossbars as a guide.

15.Lock the centering rings with a pliable adhesive.

16.Exit the service convergence adjustment mode as described in Section 2.

Section 4: ELECTRICAL CENTERING

1. Turn the power on.

2. Using a signal generator, display a crosshatch pattern.

3. Enter the service adjustment mode.

4. Check the centering of the crosshatch pattern. Use the center cross hairs of the

convergence overlay, or two pieces of string stretched diagonally across the

screen, to locate the center.

5. If the horizontal position is off, use the channel up or down key to select the HPOS

6. If the vertical position is off, use the channel up or down key to select the VPOS

7. Turn the power off to save all adjustments.

Section 5: GREEN GEOMETRY

1. Enter the service adjustment mode and then enter the convergence adjustment

mode.

2. Push the 100 key to turn off the red tube, and CH RTN/ENT to turn off the blue

tube.

3. Place the convergence overlay on the screen and align the center cross hairs

with the center of the screen.

4. Use low tack drafting tape to secure the overlay to the screen. Make the overlay

as flat as possible against the screen to reduce parallax errors.

Module No. TV-GEN-03

Page 10 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Appendix A

Readme: If the microcomputer memory IC (QA02) has been replaced, or the

crosshatch pattern is not reasonably close to the overlay pattern, make the

adjustments in Section 9. (WID, HIT, & VLIN ADJUSTMENTS). Then proceed

with step 5.

5. Push the 3 key on the remote until the blinking cursor in the upper left corner of

the screen is green.

6. Move the blinking cursor to the right with the 6 key, then down with the 8 key,

until it is one line to the right of screen center. The 4 key moves the cursor to the

left, and the 2 key moves it up.

7. Push the 5 key to lock the cursor in place.

8. Use the 2, 6, 8, and 4 keys to align the TV’s convergence pattern to the overlay

pattern.

9. Push the 5 key to unlock the cursor.

10. Move the cursor to the next location and repeat steps 7 and 8. Continue around

the screen, clockwise, from the center to the edges. Repeat the entire procedure

to make fine adjustments.

Section 6: RED CONVERGENCE

1. Remove the overlay and press the 100 key to turn on the red tube.

2. Press the 3 key until the cursor turns red.

3. Align the red convergence pattern to the green pattern, using the same

procedure used to align the green convergence pattern to the overlay.

Section 7: BLUE CONVERGENCE

1. Push the 100 key to turn off the red tube, and CH RTN/ENT to turn on the blue

tube.

2. Push the 3 key until the cursor turns blue.

3. Align the blue convergence to the green pattern, using the same procedure used

to align the green convergence pattern to the overlay.

4. Push the 100 key to turn on the red tube and check the convergence with all

three tubes on. The convergence pattern should be white with no red, green, or

blue present. A slight blue halo may result from the defocused blue CRT.

5. Exit the adjustment mode as described in Section 2.

Section 8: WHITE BALANCE

1. Turn the unit back on and check the white balance.

2. Refer to the appropriate Service Manual and adjust the white balance as needed.

3. Check the picture quality using a live video signal. If the picture quality is

acceptable, put the unit back together. If the picture quality is not acceptable,

recheck the convergence alignment.

Module No. TV-GEN-03

Page 11 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Appendix A

Section 9: WIDTH, HEIGHT, & VERTICAL LINEARITY ADJUSTMENTS

Readme: See the notes in Section 5, before performing the following procedure.

1. Exit the convergence adjustment mode as described in Section 2.

2. Press the MENU button on the unit control panel to display the RCUT register.

3. Use the channel up/ down keys to select the WID register.

4. Use the volume keys to adjust the WID register until the vertical lines are close to

those on the overlay.

5. Use the channel up/ down keys to select the HIT register.

6. Use the volume keys to adjust the HIT register until the horizontal lines are close

to those on the overlay.

7. Use the channel up/ down keys to select the VLIN register.

8. Use the volume keys to adjust the VLIN register until the horizontal lines are

close to those on the overlay.

8. If needed, repeat both the HIT and VLIN adjustments for the best results.

9. Push the 7 key to return to the convergence mode and continue with Section 5.

Module No. TV-GEN-03

Page 12 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Appendix B

4:3 Progressive Scan Units with Touch Focus

Section 1: OPTICAL & ELECTRICAL FOCUS

1. Follow the appropriate disassembly instructions to gain access to the CRTs.

2. If the wing nuts on the lenses are pointed toward the screen, reverse the lenses

on each tube so the wing nuts are facing the back of the set. Leave the lenses in

this position after servicing. Put the screen assembly back on.

Readme: The wing nuts can be accessed from the front of units with a screen

size of 50 inches or larger. The bezel assembly can be raised approximately 6

inches and locked into place using an extra set of brackets.

3. From the service mode press the 7 key on the remote control to display the

convergence crosshatch pattern.

4. Push the 100 key to turn off the red tube, and the CH RTN/ENT key to turn off

the blue tube.

5. Position a mirror for viewing the screen from the rear of the set. From the rear of

the set, loosen the wing nut on the green lens, and adjust the lens for the best

focus in the center area of the screen.

Readme: No mirror is needed for units that provide front access.

6. From the front of the set, adjust the electrical focus control for best focus in the

center of the screen.

7. Repeat the optical focus, and then tighten the wing nut.

8. Repeat the electrical focus.

9. Push the 100 key to turn on the red tube, and the 0 key to turn off the green tube.

10. Adjust the red optical and electrical focus in the same manner.

11. Push the CH RTN/ENT key to turn on the blue tube, and the 100 key to turn off

the red tube.

12. Adjust the blue optical and electrical focus in the same manner. Electrically

defocus the blue slightly, to maintain uniform brightness.

13. If the bezel assembly has been raised to allow front access, lower it into normal

position.

Section 2: MECHANICAL TILT ADJUSTMENT

1. With the set still in convergence mode, and the convergence overlay on the

screen, check each CRT’s tilt. If a CRT’s pattern is tilted loosen the appropriate

yoke with a non-magnetic screwdriver. Rotate the yoke until the pattern is

aligned vertically and horizontally. Re-tighten the yoke.

2. Press the 7 key on the remote to store the convergence data.

3. After the data is stored, “Please Press Touch Focus” will appear on screen.

Press the “Touch Focus” button on the unit control panel.

Module No. TV-GEN-03

Page 13 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Appendix B

4. “Finish” will appear on screen when the “Touch Focus” procedure is complete.

The unit will return to service mode and display a normal picture with the letter

“S” in the upper right corner.

Readme: Beginning with units in 2002, Touch Focus will run twice. The first

scan will be at a faster rate than the second scan. “CALIBRATION FINISHED”

will appear on the screen before the unit returns to the Service Mode.

5. Power the unit OFF to exit service mode.

Section 3: USER CONVERGENCE AND MAGNETIC CENTERING ADJUSTMENTS

1. Disconnect any source at the Video 1 input.

2. Turn the power on.

3. Enter the user convergence screen through the customer menu.

4. Move the red vertical cross hair as far as it will go to the right. Note the location.

Move the red vertical cross hair as far as it will go to the left. Note that location.

Set the red vertical cross hair to the center of the two extremes.

5. Move the red horizontal cross hair as far as it will go toward the top of the screen.

Note the location. Move the red horizontal cross hair as far as it will go toward the

bottom of the screen. Note that location. Set the red horizontal cross hair to the

center of the two extremes.

6. Repeat steps 4 and 5 for the blue cross hair.

7. Repeat steps 4, 5, and 6 for all user convergence adjustment points.

8. Exit the customer convergence screen.

9. Enter the service adjustment mode.

10.Enter the service convergence adjustment mode to display the crosshatch pattern.

11.Push the 100 key to turn off the red tube, and the CH RTN/ENT key to turn off the

blue tube.

12.Rotate the centering rings on the green CRT to center the green cross bar. If the

rings won't turn, remove the locking glue with a small knife. Use the center cross

hairs of the convergence overlay, or two pieces of string stretched diagonally

across the screen to locate the center of the screen.

13.Push the 100 key to turn on the red tube, and the CH RTN/ENT key to turn on the

blue tube.

14.Center the red and blue crossbars, using the green crossbars as a guide.

15.Lock the centering rings with a pliable adhesive.

16.Exit the service convergence adjustment mode as described in Section 2.

Section 4: ELECTRICAL CENTERING

1. Turn the power on.

2. Using a signal generator, display a crosshatch pattern.

3. Enter the service adjustment mode.

Module No. TV-GEN-03

Page 14 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Appendix B

4. Check the centering of the crosshatch pattern. Use the center cross hairs of the

convergence overlay, or two pieces of string stretched diagonally across the

screen, to locate the center.

5. If the horizontal position is off, use the channel up or down key to select the HPOS

6. If the vertical position is off, use the channel up or down key to select the VPOS

7. Turn the power off to save all adjustments.

Section 5: GREEN GEOMETRY

1. Enter the service adjustment mode and then enter the convergence adjustment

mode.

2. Push the 100 key to turn off the red tube, and CH RTN/ENT to turn off the blue

tube.

3. Place the convergence overlay on the screen and align the center cross hairs with

the center of the screen.

4. Use low tack drafting tape to secure the overlay to the screen. Make the overlay

as flat as possible against the screen to reduce parallax errors.

Readme: If the microcomputer memory IC (QA02) has been replaced, or the

crosshatch pattern is not reasonably close to the overlay pattern, make the

adjustments in Section 9. (WID, HIT, & VLIN ADJUSTMENTS). Then proceed

with step 5.

5. Push the 3 key on the remote until the blinking cursor in the upper left corner of

the screen is green.

6. Move the blinking cursor to the right with the 6 key, then down with the 8 key, until

it is one line to the right of screen center. The 4 key moves the cursor to the left,

and the 2 key moves it up.

7. Push the 5 key to lock the cursor in place.

8. Use the 2, 6, 8, and 4 keys to align the TV’s convergence pattern to the overlay

pattern.

9. Push the 5 key to unlock the cursor.

10.Move the cursor to the next location and repeat steps 7 and 8. Continue around

the screen, clockwise, from the center to the edges. Repeat the entire procedure

to make fine adjustments.

Section 6: RED CONVERGENCE

1. Remove the overlay and press the 100 key to turn on the red tube.

2. Press the 3 key until the cursor turns red.

3. Align the red convergence pattern to the green pattern, using the same

procedure used to align the green convergence pattern to the overlay.

Module No. TV-GEN-03

Page 15 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Appendix B

Section 7: BLUE CONVERGENCE

1. Push the 100 key to turn off the red tube, and CH RTN/ENT to turn on the blue

tube.

2. Push the 3 key until the cursor turns blue.

3. Align the blue convergence to the green pattern, using the same procedure used

to align the green convergence pattern to the overlay.

4. Push the 100 key to turn on the red tube and check the convergence with all

three tubes on. The convergence pattern should be white with no red, green, or

blue present. A slight blue halo may result from the defocused blue CRT.

5. Exit the adjustment mode as described in Section 2.

Section 8: HD CONVERGENCE

1. Turn the unit ON.

2. Input a component video signal to the HD 1 component video jacks.

3. Press the TV/VIDEO button on the remote control until HD 1 input is selected.

4. Select HD 1 Image Shape Compressed from the User Theater Menu. The video

displayed will be compressed with black panels above and below the image.

5. Repeat Sections 5, 6, and 7.

Section 9: WHITE BALANCE

1. Turn the set back on and check the white balance.

2. Refer to the appropriate Service Manual and adjust the white balance as needed.

3. Check the overall picture quality using a live video signal. If the picture quality is

acceptable, put the unit back together. If the picture quality is not acceptable,

recheck the convergence alignment.

Section 10: WIDTH, HEIGHT, & VERTICAL LINEARITY ADJUSTMENTS

Readme: See the notes in Section 5, before performing the following procedure.

1. Exit the convergence adjustment mode as described in Section 2.

2. Press the MENU button on the unit control panel to display the RCUT register.

3. Use the channel up/ down keys to select the WID register.

4. Use the volume keys to adjust the WID register until the vertical lines are close to

those on the overlay.

5. Use the channel up/ down keys to select the HIT register.

6. Use the volume keys to adjust the HIT register until the horizontal lines are close

to those on the overlay.

7. Use the channel up/ down keys to select the VLIN register.

8. Use the volume keys to adjust the VLIN register until the horizontal lines are

close to those on the overlay.

9. If needed, repeat both the HIT and VLIN adjustments for the best results.

10. Push the 7 key to return to the convergence mode and continue with Section 5.

Module No. TV-GEN-03

Page 16 of 20

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA PJTV

Digital Convergence Alignment

Appendix C

16:9 Progressive Scan Units with Touch Focus