TOSHIBA POS Terminal
ST-A10 SERIES
Owner's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Summary
SPTM-0009
Safety Summary
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions
necessary for safe handling are included in this manual. All warnings and cautions contained in this manual
should be read and understood before handling or maintaining the equipment.
Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified
using the procedures described in this manual, turn off the power, unplug the machine, then contact your
authorized TOSHIBA TEC representative for assistance.
Meanings of Each Symbol
This symbol indicates warning items (including cautions).
Specific warning contents are drawn inside the symbol.
(The symbol on the left indicates a general caution.)
This symbol indicates prohibited actions (prohibited items).
Specific prohibited contents are drawn inside or near the symbol.
(The symbol on the left indicates “no disassembling”.)
This symbol indicates actions which must be performed.
Specific instructions are drawn inside or near the ꢀsymbol.
(The symbol on the left indicates “disconnect the power cord plug from the outlet”.)
This indicates that there is the risk of death or serious injury if the
machines are improperly handled contrary to this indication.
WARNING
Do not plug in or unplug the
power cord plug with wet
hands as this may cause
electric shock.
Do not use voltages other than the
voltage (AC) specified on the
rating plate, as this may cause fire
or electric shock.
Any other than the
specified AC voltage is
prohibited.
Prohibited
Prohibited
If the machines share the same
outlet with any other electrical
appliances that consume large
amounts of power, the voltage
will fluctuate widely each time
these appliances operate. Be
sure to provide an exclusive
outlet for the machine as this
may cause fire or electric
shock.
Do not place metal objects or
water-filled containers such as
flower vases, flower pots or mugs,
etc. on top of the machines. If
metal objects or spilled liquid enter
the machines, this may cause fire
or electric shock.
Prohibited
Do not insert or drop metal,
flammable or other foreign
objects into the machines
through the ventilation slits, as
this may cause fire or electric
shock.
Do not scratch, damage or modify
the power cords. Also, do not
place heavy objects on, pull on, or
excessively bend the cords, as this
may cause fire or electric shock.
Prohibited
Prohibited
If the machines are dropped or
their cabinets damaged, first
turn off the power switches and
disconnect the power cord
plugs from the outlet, and then
contact your authorized
TOSHIBA TEC representative
for assistance. Continued use
of the machine in that condition
may cause fire or electric
shock.
Continued use of the machines in
an abnormal condition such as
when the machines are producing
smoke or strange smells may cause
fire or electric shock. In these
cases, immediately turn off the
power switches and disconnect the
power cord plugs from the outlet.
Then, contact your authorized
TOSHIBA TEC representative for
assistance.
Disconnect
the plug.
Disconnect
the plug.
(i)
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Summary
SPTM-0009
If foreign objects (metal
When unplugging the power cords,
be sure to hold and pull on the plug
portion. Pulling on the cord portion
may cut or expose the internal wires
and cause fire or electric shock.
Disconnect
the plug.
Disconnect
fragments, water, liquids) enter
the machines, first turn off the
power switches and disconnect
the power cord plugs from the
outlet, and then contact your
authorized TOSHIBA TEC
representative for assistance.
Continued use of the machine in
that condition may cause fire or
electric shock.
the plug.
Ensure that the equipment is
properly grounded. Extension
cables should also be grounded.
Fire or electric shock could
occur on improperly grounded
equipment.
Do not remove covers, repair or
modify the machine by yourself.
You may be injured by high
voltage, very hot parts or sharp
edges inside the machine.
Unauthorized modification is
prohibited.
Connect a
No
disassembling.
grounding wire.
This indicates that there is the risk of personal Injury or damage to objects if
the machines are improperly handled contrary to this indication.
CAUTION
Precautions
The following precautions will help to ensure that this machine will continue to function correctly.
ꢀ Try to avoid locations that have the following adverse conditions:
* Temperatures out of the specification
* Shared power source
* Direct sunlight
* High humidity
* Dust/Gas
* Excessive vibration
ꢀ Do not subject the machine to sudden shocks.
ꢀ Do not press the keys too hard. Keys will operate correctly if they are touched lightly.
ꢀ Clean the cover and keyboard, etc. by wiping with a dry cloth or a cloth soaked with detergent and
wrung out thoroughly. Never use thinner or other volatile solvent for cleaning.
ꢀ At the end of the day, turn the power OFF, then clean and inspect the exterior of the machine.
ꢀ Try to avoid using this equipment on the same power supply as high voltage equipment or equipment
likely to cause mains interference.
ꢀ USE ONLY TOSHIBA TEC SPECIFIED consumables.
ꢀ
DO NOT STORE the consumables where they might be exposed to direct sunlight, high temperatures, high
humidity, dust, or gas.
ꢀ When moving the machine, take hold of the drawer and lift the machine.
ꢀ Do not place heavy objects on top of the machines, as these items may become unbalanced and fall
causing injury.
ꢀ Do not block the ventilation slits of the machines, as this will cause heat to build up inside the
machines and may cause fire.
ꢀ Do not lean against the machine. It may fall on you and could cause injury.
ꢀ Place the machine on a stable and level surface.
Request Regarding Maintenance
ꢀ Utilize our maintenance services.
After purchasing the machine, contact your authorized TOSHIBA TEC representative for assistance
once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the
machines and may cause a fire or a malfunction. Cleaning is particularly effective before humid rainy
seasons.
ꢀ Our preventive maintenance service performs the periodic checks and other work required to maintain
the quality and performance of the machines, preventing accidents beforehand.
For details, please consult your authorized TOSHIBA TEC representative for assistance.
ꢀ Using insecticides and other chemicals
Do not expose the machines to insecticides or other volatile solvents. This will cause the cabinet or
other parts to deteriorate or cause the paint to peel.
(ii)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
TABLE OF CONTENTS
Page
1.
2.
INTRODUCTION ----------------------------------------------------------- 1-1
1.1 Accessories --------------------------------------------------------------------------------
1-1
APPEARANCE ------------------------------------------------------------- 2-1
2.1 Standard Model ----------------------------------------------------------------------------
2.2 Availabe Options ---------------------------------------------------------------------------
2.3 Examples of POS Terminal with Some Options -----------------------------------
2.4 Connectors ----------------------------------------------------------------------------------
2-1
2-3
2-4
2-5
3.
4.
INSTALLATION PROCEDURE --------------------------------------
3.1 Environment for Installation -------------------------------------------------------------
3.2 Connecting the AC Plug -----------------------------------------------------------------
3-1
3-1
3-2
ADJUSTMENT -------------------------------------------------------------- 4-1
4.1 Tilt Angle Adjustment --------------------------------------------------------------------
4.2 Brightness Adjustment ------------------------------------------------------------------
4-1
4-2
5
MAGNETIC CARD READER (OPTION)------------------------------ 5-1
5.1 How to Read Magnetic card ------------------------------------------------------------
5-1
®
6.
6-1
6-1
iButton (OPTION) -------------------------------------------------------
6.1 How to Read iButton ----------------------------------------------------------------------
7.
8.
9.
GENERAL MAINTENANCE --------------------------------------------- 7-1
TROUBLESHOOTING ---------------------------------------------------- 8-1
SPECIFICATIONS -------------------------------------------------------- 9-1
9.1 Basic Specifications ---------------------------------------------------------------------
9.2 Option ----------------------------------------------------------------------------------------
9-1
9-2
CAUTION!
1. This manual may not be copied in while or in part without prior written
permission of TOSHIBA TEC.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorized Service representative with regard
to any queries you may have in this manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
1. INTRODUCTION
1.1 Accessories
1. INTRODUCTION
Thank you for choosing the TOSHIBA POS Terminal. This POS terminal contains all the high
performance register functions necessary for a specialty/hospitality POS terminal and enables the
user oriented system configuration.
The operation panel can be chosen from 12-inch TFT display and 15-inch TFT display.
This manual describes the functions and handling of this POS terminal and should be read
carefully to help gain maximum performance and life from your POS terminal. For more queries
please refer to this manual and keep it safe for future reference.
1.1 Accessories
Confirm that the following accessories are contained in the carton. If any accessories are missing
or damaged, contact your TOSHIBA TEC service representative.
Quick installation manual (1 copy)
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
2. APPEARANCE
2. 1 Standard Model
2. APPEARANCE
2.1 Standard Model
12-inch display POS terminal
15-inch display POS terminal
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
2. APPEARANCE
2. 1 Standard Model
LED and CONTROL BUTTON
DESCRIPTION
This is the LED to indicate the power ON/OFF
status of the POS terminal. The blue LED is
illuminated when the power is ON.
Power LED (Blue)
The yellow LED is illuminated during the
access to the hard disk drive.
HDD LED (Yellow)
Power Switch
This is the switch to turn the power of the POS
terminal ON or OFF.
This is used to adjust the brightness of the
operator’s display.
Brightness Control
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
2. APPEARANCE
2.2 Available Options
2.2 Available Options
Wireless Adaptor Case
Fixed type customer display
BIU
Magnetic Card Reader
(MCR)
Tilt type customer display
BIU
iButton
Remote type customer display
RIU
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
2. APPEARANCE
2.3 Examples of POS Terminal with Some Options
2.3 Examples of POS Terminal with Some Options
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
2. APPEARANCE
2.4 Connectors
2.4 Connectors
CAUTION!
The drawer interface connector is exclusively for connecting the drawer. Do not connect a
phone line or any other cables than the drawer cable to this connector. Doing so may cause a
failure of the phone line and this terminal.
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
2. APPEARANCE
2.4 Connectors
Connector
Description
A connector for the AC inlet
AC inlet
PS/2 (Mouse, Keyboard) Mini-DIN 6-
pin female type connector
Connector for the PS/2 type mouse, Connector for the
PS/2 type keyboard
Connector for the USB (Universal Serial Bus) interface
USB V2.0/1.1 and UHCI (Conforming to Universal Hub
Controller Interface V2.0/1.1)
USB: General 5V USB X 6
NOTE: USB functions may not be supported
depending on the Operating System.
USB: 24V Powered
X 1
USB 6 ports can be used as general 5V USB
connectors. Powered USB is a USB socket supplied
with power, which is 1 port of 24V USB.
Modular type connector for the 10BASE-T/100BASE-
TX LAN interface, RJ-45 modular connector (with LED)
LAN
Connector for integrated Vacuum Fluorescent Display
NOTE: When BIU is installed on the POS
terminal, RIU is not available.
BIU connector
Connector for external Vacuum Fluorescent Display
NOTE: When RIU is installed on
RIU connector
the POS terminal, BIU is not available.
Cash drawer
A 24V type TEC interface drawer is connectable
Connectors for Speaker and Mic
Speaker & Mic
Expandable VGA interface. 15-pin VGA female type
connector
VGA
COM 1, 2
D-sub 9-pin male type connector (without power)
D-sub 9-pin female type connector (with power)
COM 3
LVDS connector
MCR connector
A connector for Tablet
A connector for magnetic card reader (MCR)
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
3. INSTALLATION PROCEDURE
3.1 Environment for Installation
3. INSTALLATION PROCEDURE
WARNING!
Care must be taken not to get your fingers caught between the LCD Frame and the POS terminal
when bending the display downward.
CAUTION!
When removing the protective film from the display surface, please be sure to do it slowly. If it is
done quickly, static electricity may generate, and the TFT may be damaged.
3.1 Environment for Installation
CAUTION!
When installing the POS terminal, take the following precautions. Failure to do this may cause
fire, electric shock, or injury.
1. Avoid locations where it is subject to the following:
• Direct sunlight
• High temperature, high humidity
• Rapid change in temperature
• Excessive vibration
• Dust
2. Keep away from any devices that emit magnetism or electromagnetic wave.
3. Keep away from flame or moisture.
4. Be sure to place the POS terminal on a level and stable surface.
1. Place the POS terminal on a level surface.
2. Provide a minimum space to the left, right, front and rear of the POS terminal for proper cooling.
(The unit has air vents and a fan on the front and left. Spaces should be provided to prevent the
air vents from being blocked and the airflow from being obstructed.)
See NOTE
See NOTE
NOTE: Do not block the ventilation of the fan. Fan is provided on these sides.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
3. INSTALLATION PROCEDURE
3.2 Connecting the AC Plug
3.2 Connecting the AC Plug
1. Push on both sides of the molded Tower (TWR) Tail Cover to remove it from the system in order to
gain access of the AC inlet.
2. Fully insert the Power Cord Plug into the Inlet of the POS terminal.
Power
Cord Plug
TWR Tail
Cover
Inlet
Push
Power
Cord Plug
Push
Lift
NOTE: The Power cord is not included in the carton. Please prepare it separately from local dealer.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
4. ADJUSTMENT
4.1 Tilt Angle Adjustment
4. ADJUSTMENT
Tilt angle and brightness of the operator’s display can be adjusted.
Adjustment method is common to both of 12-inch display model and 15-inch display model.
CAUTION!
1. Do not adjust the display angle by holding the LCD panel. Doing so may damage the unit. Be
sure to hold the LCD frame.
2. Care must be taken not to catch your fingers between POS terminal and the LCD Frame when
bending the display backward.
4.1 Tilt Angle Adjustment
The tilt angle of the operator’s display can be adjusted freely from 10° to 60°.
Hold both sides of the LCD frame, and slowly push the display upward/ downward to your best
angle.
The angle of the optional BIU (Tilt type customer display) is also adjustable as follows.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
4. ADJUSTMENT
4.2 Brightness Adjustment
4.2 Brightness Adjustment
The brightness control is provided on the lower right of the operator’s display.
Turning it to the left makes the display darker, and turning it to the right makes the display brighter.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
5. MAGNETIC CARD READER (OPTION)
5.1 How to Read Magnetic Card
5. MAGNETIC CARD READER (OPTION)
The optional magnetic card reader can be installed.
5.1 How to Read Magnetic Card
Insert the magnetic card into the upper portion of the magnetic card reader slot and slowly
move the card downward.
NOTE: Moving the magnetic card too fast or too slowly may cause a read error.
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
6. iButton® (OPTION)
6.1 How to Read iButton
®
6. iButton (OPTION)
The optional iButton unit can be installed on the bottom of the LCD.
6.1 How to Read iButton
CAUTION!
1. Keep storage media, like a floppy disk, away from the touch probe. The magnet of the touch
probe may destroy the stored data.
2. Keep a metal object like a paper clip away from the touch probe. If such an object is attached
to the touch probe, it may cause a short-circuit
Data stored in an iButton can be read by attaching the iButton key to the touch probe. The magnet of
the touch probe holds the iButton key.
iButton Unit
(Option)
iButton Key
NOTE: iButton key is local procurement
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
7. GENERAL MAINTENANCE
7. GENERAL MAINTENANCE
7. GENERAL MAINTENANCE
WARNING!
1. Be sure to disconnect the power cord prior to performing any maintenance.
2. Do not pour water directly on or wipe the operator’s display with a soaked cloth, as this may
cause fire, electric shock, or machine failure.
CAUTION!
1. Never use an organic solvent like thinners or benzene for cleaning. Using such solvents may
discolor the covers.
2. Do not use any sharp object to clean the operator’s display. Doing so may cause an operator’s
display failure.
3. Do not insert the nozzle of an air blower into the magnetic card reader slot. Doing so may
damage the scanning head, resulting in the magnetic card reader failure.
To help retain the high quality and performance of your POS Terminal, it should be cleaned
regularly. The greater the usage on the POS Terminal, the more frequent the cleaning. (i.e. low
usage = weekly: high usage = daily)
• Cleaning the Operator’s Display
Clean the surface of the operator’s display with a soft dry cloth or with an electrostatic free cleaner
for automated office equipment.
• Cleaning the Covers
Wipe the covers with a soft dry cloth or soft cloth slightly moistened with mild detergent. After
using detergent for cleaning, be sure to wipe it off with a slightly moistened cloth.
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
8. TROUBLESHOOTING
8. TROUBLESHOOTING
8. TROUBLESHOOTING
WARNING!
If you cannot solve a problem with the following solutions, do not attempt to repair it by
yourself. Turn the power off, unplug the POS Terminal, then contact the nearest TOSHIBA
TEC service representative for assistance
Symptom
The power does not turn
on.
Check Point
• Is the power cord plugged in
correctly?
• Is the power supplied to the
AC outlet?
Solution
• Plug in correctly.
• If it is not a power failure,
check for the power supply to
the AC outlet with another
electric appliance.
When the power is not
supplied, contact your nearest
power company.
• Has the circuit breaker
blown?
• Check the circuit breaker.
The operator’s display is
hard to see
• Does the operator’s display
reflects sunlight or room light? Adjustment and adjust the
• Refer to Section 4
• Is the tilt angle adjusted
properly?
• Is the brightness adjusted
properly?
display angle.
• Refer to Section 4
Adjustment and adjust the
brightness properly.
Magnetic card reader
does comply-not read the
data.
• Does the used card comply
with the standard?
• Was the card moved too fast
or too slowly?
• Is the card reading direction
correct?
• Use ISO Track 1,2,3
complying MCR.
• Move the card at the proper
speed. (10~150 cm/sec.)
• Insert the card so that the
magnetic strip faces the
scanning head.
NOTE: If any problem occurs other than the above, please contact your authorized TOSHIBA
TEC representative.
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
9. SPECIFICATIONS
9.1 Basic Specifications
9. SPECIFICATIONS
9.1 Basic Specifications
Item
Description
VIA C7 1.5GHz
CPU
512 MB, 2 slots (2 GB max)
3.5" HDD SATA (40 GB)
Memory
HDD
ISO-3-track one sided type (option)
MCR
Option
iButton Reader
RS-232C
4 (2x normal. 1x powered, 1x RIU connector)
USB
6
Powered USB
PS/2
Drawer
VGA
1
PS/2 Keyboard & PS/2 Mouse
2
Interface
1
10BASE-T/100BBASE-TX Ethernet
RJ-45 modular connector (with LED)
LAN
Line-out/Mic-in
Audio
5°C - 40°C / 41F –104F
10%-80% RH (Non condensation)
Operating Temperature
Operating Humidity
12-inch LCD
306mm (L) X 247mm (W) X 339mm (H) / 12” (L) X 9.7” (W) X 13.3” (H)
366mm (L) X 251mm (W) X 360mm (H) / 14.4” (L) X 9.9” (W) X 14.2” (H)
10.5 Kg / 23.1lb (Gross)
Dimensions
Weight
15-inch LCD
12-inch LCD
15-inch LCD
11.5 Kg / 25.4 lb (Gross)
Power Supply
Support OS
95W Continuous Duty/150W Maximum Internal Switching Supply
Win2000, XP, WEPOS, Linux Suse 9.3
12-inch display
12.1-inch color TFT with touch panel
12.1-inch 800 x 600 dots
15-inch display
15-inch color TFT with touch panel
15-inch 1024 x 768 dots
Display type
Display size
Number of
Colors
Brightness
Display area
Dot size
262K Color (262,144 Colors)
230 cd/m2
246 mm (W) x 184.5 mm (H)
0.3075 mm (W) x 0.3075 mm (H)
Analog Resistor Film
(1024 x 1024 dots)
262K Color (262,144 Colors)
250 cd/m2
304.1 mm (W) x 228.1 mm (H)
0.297 mm (H) x 0.297 mm (H)
Analog Resistor Film
(1024 x 1024 dots)
Operator’s
Display
Touch panel
Brightness volume (TFT) and Tilt angle (Free adjustment in a range of 10° to
Adjustment
mechanism
60°)
No swivel adjustment
Number of
displayed
5 x 7 dot fluorescent display 20 digits x 2 lines
characters
Display colour
Blue
Display area/
character size
Character size: 5.5 mm (W) x 10.5mm (H)
Character pitch: 7.4 mm (W) x 15.5 mm (H)
Customer
Display
Type font
Display angle
(tilt type)
182 types of half width ANK
Tilt: 0° to 45°
Swivel: 0° to 145° (in both directions)
(Option)
Interface
RS-232C interface (with power)
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPTM-0009
9. SPECIFICATIONS
9.2 Options
9.2 Options
Option
Model
Description
24V-drive standard drawer
Dimensions and Weight:
460(W) x 400(D) x 115(H) mm / 18.1(W) x 15.7 (D) x 4.5(H) inch
10 Kg / 22 lb
DRWST-51A-4MVK-QM-R
DRWST-51A-8MVK-QM-R
Money Case Type: MC4, 8
Drawer Unit
Bill
Holder
Coin
Tray
Type
Mini Coin Case CDC
Remarks
Drawer
4MVK-QM
Type
5
5
6
No
1
Yes With media Slot
Yes With media Slot
8MVK-QM
4
Tilt: 0° to 45°
Swivel: 0° to 145° (in both direction)
20 Characters x 2 lines dot display to be installed onto the POS
terminal
Tilt Type
Customer
Display
LIUST-A10-BAK-QM-R
Fixed Type
Customer
Display
Fixed (no tilt and no swivel)
20 Characters x 2 lines dot display to be installed onto the POS
terminal
LIUST-A10-FAK-QM-R
Remote Type
Customer
Display
Remote: Connected to terminal with an extended cable
20 Characters x 2 lines dot display to be connected to the POS
terminal
LIUST-A10-RAK-QM-R
TRST-A10 /A15 series
Single thermal printer : TRST-A10
Single thermal printer (Dual side printing): TRST-A15
Printer Unit
Magnetic
Card Reader MCRST-A10-5K-QM-R
(MCR)
ISO Track 1,2,3 type magnetic card reader kit
iButton unit to be installed onto the POS terminal (An iButton key is
not included)
iButton
KIT-A10-BTNK-QM-R
KIT-A10-WLCK-QM-R
Wireless
Adaptor Case
Case and extension cable only
9-2
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Waste Recycling information for users:
Following information is only for EU-member states:
The crossed out wheeled bin symbol is used to indicate that the product must not be treated as general household waste.
By ensuring that this product is disposed of correctly you will be helping to prevent potentially negative consequences for
the environment and human health, which could otherwise be caused by incorrect waste handling of this product.
For more detailed information about the take-back and recycling of this equipment, please contact the supplier that
provided you with the product in question.
French
Information aux utilisateurs concernant le recyclage des déchets:
Les informations suivantes sont uniquement destinées aux pays membres de l’Union Européenne:
L’utilisation du symbole de "poubelle à roulettes barrée" indique que ce produit ne doit pas être traité comme un déchet
ménager classique.
En vous assurant que ce produit est correctement mis au rebut, vous participerez à la prévention de l’environnement et
de la santé publique, contre des conséquences négatives potentielles qui pourraient résulter d’un traitement inapproprié
des déchets de ce produit. Pour obtenir des informations complémentaires concernant la récupération et le recyclage de
ce produit, veuillez contacter le fournisseur auprès duquel vous avez acheté le produit.
German
Wiederverwertungsinformationen für Verbraucher:
Die folgenden Informationen gelten nur für EU-Mitgliedsstaaten:
Das durchgestrichene Mülltonnensymbol weist darauf hin, dass dieses Produkt nicht wie allgemeiner Haushaltsmüll
behandelt werden darf.
Indem Sie aktiv mitwirken, dieses Produkt ordnungsgemäß zu entsorgen, helfen Sie mit, mögliche negative
Auswirkungen auf die Umwelt sowie die menschliche Gesundheit zu vermeiden, die sonst durch die unsachgemäße
Entsorgung dieses Produktes beeinträchtigt werden könnten.
Für nährere Informationen zur Rücknahme und Wiederverwertung dieses Produktes wenden sie sich bitte an den
Lieferanten, von dem Sie dieses Produkt erworben haben.
Spanish
Información para usuarios sobre el reciclaje de residuos:
La siguiente información sólo concierne a los Estados Miembros de la UE:
El uso del símbolo de un contenedor con ruedas tachado indica que este producto no puede ser tratado como si fuera
un residuo doméstico.
Asegurando que nos deshacemos de este producto de forma correcta, ayudaremos a evitar potenciales consecuencias
negativas tanto para el medio ambiente como para la salud pública, que podrían producirse debido a un tratamiento
inapropiado de este producto. Para obtener una información más detallada sobre la recogida y reciclaje de su producto,
por favor, póngase en contacto con el proveedor donde lo compró.
Dutch
Gebruikersinformatie over het recycleren van afval:
De volgende informatie geldt enkel in EU-lidstaten:
Het symbool met de doorkruiste afvalbak geeft aan dat dit product niet mag worden behandeld als algemeen
huishoudelijk af val.
Door dit product op de juiste manier van de hand te doen beschermt u het milieu en de volksgezondheid tegen mogelijke
negatieve gevolgen, die anders zouden kunnen voortvloeien uit het onjuist verwerken van de resten van dit product.
Voor gedetailleerde informatie over het terugnemen en recycleren van dit product, gelieve contact op te nemen met de
leverancier van dit product.
Italian
Informazioni sul riciclo del prodotto:
Le seguenti informazioni riguardano gli stati membri EU:
Il simbolo con il bidone sbarrato indica il non poter smaltire questo prodotto come rifiuto domestico.
L'accertamento che questo prodotto sia smaltito correttamente contribuirà ad impedire le potenziali conseguenze
negative per l'ambiente e la salute umana che potrebbero essere causati, al contrario, dall'errato smaltimento dello
stesso. Per informazioni più dettagliate sulle modalita di resa e riciclaggio di questo prodotto mettetevi in contatto con il
fornitore da cui l'avete aquistato.
Portuguese
Informação sobre reciclagem:
A informação que se segue é apenas dirigida a países membros da CEE:
A utilização deste símbolo indica que este produto não pode ser tratado como lixo comum.
Ao assegurar-se que este produto é tratado correctamente está a ajudar a prevenir potenciais consequências negativas
para o ambiente e para a saúde humana, que poderiam ser causadas pelo inapropriado tratamento deste produto.
Para mais informação sobre a reciclagem e tratamento deste produto, contacte o seu fornecedor.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTED IN SINGAPOLE
SPTM-0009
E
Download from Www.Somanuals.com. All Manuals Search And Download.
|