E6581299c
USB-to-Serial Conversion Unit Instruction Manual
USB001Z
Contents
1. Exterior features ･････････････････････････････････････････････････････････････････････4
2. Installing the device driver ･････････････････････････････････････････････････････････････5
2.1. Windows 2000 or Windows XP ････････････････････････････････････････････････5
2.2. Windows 98 SE ･････････････････････････････････････････････････････････････9
2.3. Uninstalling the device driver ･････････････････････････････････････････････････11
3. Checking the COM port number ･･･････････････････････････････････････････････････････12
4. Connecting and starting the USB001Z unit･･････････････････････････････････････････････14
5. Outline drawing ･････････････････････････････････････････････････････････････････････15
6. Specifications･･･････････････････････････････････････････････････････････････････････16
7. Warranty･･･････････････････････････････････････････････････････････････････････････16
NOTICE
1. Make sure that this instruction manual is delivered to the end user of USB-to-
serial conversion unit.
2. Read this manual before installing or operating the USB-to-serial conversion
unit. Keep it in a safe place for reference.
3. All information contained in this manual are subject to change without notice.
Please confirm the latest information on our web site “www.inverter.co.jp”.
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
Read first
Safety precautions
This instruction manual and the inverter unit contain important information to avoid endangering
actual operators and other persons and damaging properties and to ensure the proper and safe
product usage.
Before reading this manual, fully understand the safety precautions in the instruction manual
accompanying your inverter. Also, strictly observe the precautions described in this manual.
„ Limits in purpose
Never use the USB-to-serial conversion unit with any device other than a TOSVERT series inverter, or it could cause an
accident.
„ General Operation
Danger
Never disassemble, modify or repair.
Disassembly
prohibited
This can result in electric shock, fire and injury. For repairs, call your sales agency.
Don’t place or insert any kind of object into the inverter (electrical wire cuttings, rods,
wires). This can result in electric shock or fire.
Prohibited
That may result in electric shock or fire.
Do not allow water or any other fluid to come in contact with this unit. Do not wipe this unit
with a wet cloth. That may result in electric shock or fire.
Before attempting any wiring steps, power off your inverter and make sure that the inverter
charge lamp is no longer lit.
Mandatory
If this unit begins to emit smoke or an unusual odor, or unusual sounds, immediately turn
power off.
If the equipment is continued in operation in such a state, the result may be fire. Call your
local sales agency for repairs.
„ Transportation & installation
Danger
Do not place any inflammable substances near this unit.
If an accident occurs in which flame is emitted, this could lead to fire.
Prohibited
Do not connect a LAN cable or modular cable for telephones to the conversion unit. Doing
so could cause a failure or accident.
Do not connect more than one conversion unit to one host device (computer). Doing so
could cause a failure or accident.
Operate under the environmental conditions prescribed in the instruction manual.
Operations under any other conditions may result in malfunction.
Mandatory
Provide your inverter or other equipment with safety devices to prevent a serious accident
from resulting even if the unit malfunctions or fails to operate. Usage without a safety
device can result in an accident.
Use the Toshiba-specified cable for connecting this optional unit. (Refer to page 4.)
The use of any other option may result in an accident.
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
„ Operations
Danger
Do not apply a dropping shock or other physical shocks.
Otherwise, damage or malfunction will result.
Do not yank the interconnect cable.
Prohibited
Otherwise, damage or malfunction will result.
Even if this product is deactivated by the occurrence of an event such as an abnormality,
when power is supplied to the inverter, do not bring any regions of your body into contact
with the inverter terminals. Contact during the power-on status of the inverter can result in
electric shock.
„ Disposal
Warning
If you throw away this unit, have it done by a specialist in industry waste disposal*. If you
throw away the inverter by yourself, this can result in explosion of capacitor or produce
noxious gases, resulting in injury.
Mandatory
(*) Persons who specialize in the processing of waste and known as “industrial waste
product collectors and transporters” or “industrial waste disposal persons.” If the
collection, transport and disposal of industrial waste is done by someone who is not
licensed for that job, it is a punishable violation of the law. (Laws in regard to cleaning and
processing of waste materials)
„ Cautions in using the unit
Notes
Do not install the unit where it will be exposed to abrupt changes in temperature or
humidity.
Leave space between the interconnect cable (between the inverter and the USB device)
and the power cable from the inverter. Or the inverter could malfunction because of noise.
Do not connect the conversion unit to more than one inverter. Connect the conversion unit
to either the “RS485 (2-wire type)” port or the “LOGIC” port on your inverter, depending on
the type of the inverter.
Do not disconnect the USB cable during communication with the inverter.
Avoid connecting the conversion unit to a USB hub or extended USB port (e.g., PCMCIA
card). Or else the conversion unit may become unstable, depending on the environment in
which it is used.
To allow an emergency stop by means of an external device, insert a magnetic contact or
similar device between the inverter and the power supply.
„ Caution in creating a software program
Notes
The communications software created based on the instruction manual for each
TOSVERT series communication function can be used as-is, if the COM port number is
changed properly. The conversion unit may, however, be detached from the operating
system as a result of a transmission error due to noise, and therefore the occurrence of
transmission timeout errors should be monitored using the software, and if they occur in
succession, open the port again.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
1. Exterior features
(1) Here are the names and functions of the exterior components of the USB001Z unit.
(1) RS485 (2-wire type) communication port
RS485(2wire type)
Used to connect to the RS485 (2-wire
type) port on the inverter
LOGIC
Applicable model: VF-AS1 and so on
USB
(2) Common serial communication port
Used to connect to the common serial
port on the inverter
Option Unit
USB
Applicable model: VF-S11, VF-nC1
VF-S9, VF-A7
VF-P7, other models
(3) USB communication port
Used to connect to a USB port on the
PC
(2) Interconnect cables (No cables are included with this converter unit.)
- Inverter side (Point of connection: Either (1) or (2) in the above figure)
Use one of the optionally available Toshiba-specified cables listed below.
Inverter-to-unit interconnect cable
Cable length
1.2m
CAB0011
CAB0013
CAB0015
3.6m
4.8m
- USB device side (Point of connection: (3) in the above figure)
Use a commercially available USB cable.
(Compliant with USB 1.1/2.0, A-B connection type)
Recommended cable length: 1 m or less
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
2. Installing the device driver
When using the USB001Z unit for the first time, you have to install its driver on your computer. Since the
steps to be followed to install the driver vary depending on the operation system used, refer to the section
that corresponds to the operating system used.
These steps do not need to be performed from the next time onward.
Note: Unless otherwise specified, the term “click” means “left-click” (default setting) in the following
chapters.
2.1. Windows 2000 or Windows XP
* In this example, Windows XP SP1 is used.
(1) Turn on your computer and start Windows.
Note: Log on to Windows as a computer administrator.
(2) Connect the USB001Z unit to the computer with a USB cable.
* At this time, do not connect the USB001Z unit to the inverter.
The message “@Found New hardware” appears on the screen of your computer monitor, and the
“@Found New Hardware Wizard” appears after a short while, as shown in the figure below.
Click the checkbox for “@Install from a list or specific location (Advanced)” in the window, make
sure a check mark is put in the checkbox, and then click [Next].
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
(3) Insert the supplied floppy disk in the floppy disk drive.
(4) Specify the path to the device driver.
In the “@Found New Hardware Wizard” window, click the checkbox for “@Search the best driver in
these locations” click the checkbox for “@Search removable media (floppy, CD-ROM...)” to select it,
and then click [Next]. (In the case of Windows 2000, the message displayed here is slightly different
from the above, but select “@Floppy disk” anyway)
(5) The installation of the device driver starts.
* If the message “USB001Z has not passed Windows Logo testing to verify its compatibility with
Windows XP.” appears during installation, click [Continue Anyway].
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
(6) The installation of the device driver is now complete.
On completion of the installation, the window shown below appears. Then, click [Finish].
The floppy disk is also used in step (7), so do not eject it yet.
(7) Then, the installation of the USB port driver starts.
The “@Found New Hardware Wizard” appears again.
The USB port driver is also contained on the supplied floppy disk. So, perform steps (3) through (6)
again.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
(8) Complete the installation.
When a window appears, telling you that the driver has been installed successfully, click [Finish] to
complete the installation. Eject the floppy disk, put it in its case, and store it along with this instruction
manual.
The COM port number is needed for communications with the inverter. So, check on the COM
number, following the steps described in section 3.
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
2.2. Windows 98 SE
(1) Turn on your computer and start Windows.
(2) Connect the USB001Z unit to the computer with a USB cable.
* At this time, do not connect the USB001Z unit to the inverter.
After a while, the “@Add New Hardware Wizard” appears on the screen of your computer monitor,
as shown in the figure below. Then, click [Next].
(3) Specify a way to search for the driver.
Click the checkbox for “@Search for the best driver for your device (Recommended)” in the window,
make sure a check mark is put in the checkbox, and then click [Next].
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
(4) Insert the supplied floppy disk in the floppy disk drive.
After inserting the floppy disk, click the checkbox for “Floppy disk drives” in the window, make sure
a check mark is put in the checkbox, and then click [Next].
(5) A search for the driver file is made automatically.
Click [Next].
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
(6) The installation of the device driver starts.
On completion of the installation, the window shown below appears. Then, click [Finish].
Do not eject the floppy disk yet, because the USB port driver will be installed next.
(7) Then, the USB port driver is installed automatically and the installation of all necessary
drivers is completed.
The COM port number is needed for communications with the inverter. So, check on the COM port
number, following the same steps described in chapter 3.
2.3. Uninstalling the device driver
* To uninstall the device driver, click “Start” button on Windows, click “Control Panel” in start menu
and turn on “Add/Remove Programs”. In the program list that appeared, select “USB Serial
Converter Driver” and then click [Change/Remove].
When the uninstaller starts, check to make sure that the conversion unit is not connected, and
then click “Continue.”
Warning
Do not uninstall a device driver where this option is connected with your computer.
Otherwise, abnormalities may be caused to your computer.
Mandatory
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
3. Checking the COM port number
The COM port number is needed for communications with the inverter. So, follow these steps to
check on it.
The COM port number is recognized automatically when the installation of the device driver is
completed. COM port numbers vary depending on how your computer is set up.
* Perform this check with the USB001Z unit connected to your computer, or else the port number
cannot be checked.
(1) Click “Start” button on Windows, RIGHT-click “My Computer,” and select “Properties” from
the menu that appears.
(In the case of Windows 2000 and Windows 98 SE, the “My Computer” folder is placed on the
desktop.)
(2) Click the “Hardware” tab of the “System Properties” dialog box.
(If you are using Windows 98 SE, click the “Device Manager” tab and go to step (4).)
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
(3) Click the “Device manager” button in the “Hardware” menu.
(4) Click the [+] sign on the left side of “@Port (COM/LPT).”
The number in parentheses next to “USB/Serial Port” refers to the COM port number. (In the
example shown below, the COM port number is “COM3.”)
(If the USB001Z unit is not connected, no COM port number is shown.)
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
4. Connecting and starting the USB001Z unit
To connect the USB001Z unit to your computer, follow these steps:
1) Turn off the input power to the inverter, and after waiting for at least 15 minutes, make sure that the
charge lamp on the inverter is no longer lit. (Your personal computer can remain powered on.)
2) Connect a USB cable to the USB port on the USB001Z unit and to a USB port on your computer.
When connecting the USB001Z unit to your computer for the first time, you
have to install its driver. Refer to Section 2.
3) Connect an inverter-unit connection cable (optional) between the communication connector of the
USB001Z and that of the inverter. At this time, be careful not to apply force to the connectors.
(Refer to the instruction manual of the inverter for connection to the connection port of the
inverter.)
RS 485 (2-wire type) side: Connectable to such an RS485 (2-wire type) interface port as
that of the VF-AS1.
LOGIC side:
Connectable to such a common serial interface port as that of
the VF-nC1, S9, S11, A7, or P7.
* Connect the cable only to either RS485 or LOGIC.
4) Turn on the power to the inverter, and set communication parameters.
* Before disconnecting the USB communication unit, also perform above step 1) beforehand.
„ Example of connection (In the case of the VF-AS1)
RS485 (2-wire type)
LOGIC
USB
Option Unit
VF-AS1
USB
Computer
(USB port)
- Inverter-unit connection cable (Optional)
- USB cable (A-B connection type)
Use a commercially available USB cable.
(Compliant with USB 1.1/2.0)
Model number
CAB0011
Cable length
1.2m
Recommended cable length: 1m
CAB0013
3.6m
CAB0015
4.8m
Warning
Do not disconnect the USB cable during communication with the inverter.
Prohibited
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
5. Outline drawing
Here is an outline drawing of the USB001Z unit. (Unit: mm)
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E6581299c
6. Specifications
Item
Specifications
Model number
USB001Z
Model with either an RS485 (2-wire type) connector or a common serial connector
(optional).
Applicable model
Usable applications: PCM001Z (V013 or successor), PCS001Z (V001 or successor)
Windows 98 SE , Windows 2000, Windows XP SP1 *1
Applicable OS
However, the personal computer *2 must have a USB port (series A).
Indoor operation at an altitude of 1,000m or less and free from direct sunlight,
Use environments potentially corrosive or explosive gases, steam, dust particles, dust/dirt, and
machining fluids (grinding liquid, coolant, included)
Ambient temperature 0 to +50°C
Storage temperature -25 to +65°C
Relative humidity 20 to 93% (free from condensation and vapor)
Vibration
Cooling method
5.9m/s2 (0.6G) or less (10 to 55Hz) (Compliant with JIS C 0040)
Self-cooling
*1: Windows® is listed above as the abbreviation for a Microsoft® Windows® operating system.
Microsoft® and Windows® are registered trademarks or trademarks of the US Microsoft Corporation
in the USA and other countries.
*2: No warranty as to the suitability of this product for any computer and any peripheral equipment is
either made or implied.
7. Warranty
Any part of the unit that proves defective will be repaired free of charge under the following
conditions:
1. This product will be repaired free of charge, if some trouble occurs under normal handling within
one year of delivery and is caused obviously by a defect in design or workmanship.
2. The warranty applies only to the delivered unit.
3. For the following kinds of failure or damage, the repair cost shall be borne by the customer even
within the warranty period.
1) Failure or damage caused by improper or incorrect use or handling, or unauthorized repair or
modification of the inverter
2) Failure or damage caused by the unit falling or an accident during transportation after the
purchase
3) Failure or damage caused by fire, salty water or wind, corrosive gas, earthquake, storm or
flood, lightning, abnormal voltage supply, or other natural disasters
4) Damage due to the use of the USB-serial communication conversion unit for non-intended
purposes.
4. If there are any warranty conditions otherwise provided for, those conditions will govern.
- 16E -
Download from Www.Somanuals.com. All Manuals Search And Download.
|