Toshiba Flat Panel Television DL66 User Manual

TOSHIBA  
WL66/67  
EL66/67  
DL66/67  
Series  
Owner's manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Precautions  
This equipment has been designed and manufactured to meet international safety standards but, like any  
electrical equipment, care must be taken to obtain the best results and for safety to be assured. Please read  
the points below for your own safety. They are of a general nature, intended to help with all electronic  
consumer products and some points may not apply to the goods you have just purchased.  
DO NOT REMOVE ANY FIXED COVERS AS THIS  
WILL EXPOSE DANGEROUS AND 'LIVE' PARTS.  
Air Circulation  
Leave at least 10cm clearance around the television  
to allow adequate ventilation. This will prevent  
overheating and possible damage to the television.  
Dusty places should also be avoided.  
THE MAINS PLUG IS USED AS A  
DISCONNECTING DEVICE AND THEREFORE  
SHOULD BE READILY OPERABLE.  
Do not  
Heat Damage  
obstruct the ventilation openings of the  
equipment with items such as newspapers,  
tablecloths, curtains, etc. Overheating will cause  
damage and shorten the life of the equipment.  
Damage may occur if the television is left in direct  
sunlight or near a heater. Avoid places subject to  
extremely high temperatures or humidity. Place in a  
location where the temperature remains between  
allow electrical equipment to be exposed  
to dripping or splashing or objects filled with liquids,  
such as vases, to be placed on the equipment.  
5°C (41°F) min. and 35°C (94°F) max.  
Mains Supply  
place hot objects or naked flame sources,  
such as lighted candles or nightlights on, or close to  
equipment. High temperatures can melt plastic and  
lead to fires.  
The mains supply required for this equipment is  
220-240v AC 50/60Hz. Never connect to a DC  
supply or any other power source. DO ensure that  
the television is not standing on the mains lead.  
DO NOT cut off the mains plug from this  
equipment, this incorporates a special Radio  
Interference Filter, the removal of which will impair  
its performance. In the UK, the fuse fitted in this  
plug is approved by ASTA or BSI to BS1362. It  
should only be replaced by a correctly rated and  
approved type and the fuse cover must be refitted.  
IF IN DOUBT PLEASE CONSULT A COMPETENT  
ELECTRICIAN.  
use makeshift stands and NEVER fix legs  
with wood screws. To ensure complete safety,  
always fit the manufacturers’ approved stand,  
bracket or legs with the fixings provided according  
to the instructions.  
listen to headphones at high volume, as  
such use can permanently damage your hearing.  
leave equipment switched on when it is  
unattended, unless it is specifically stated that it is  
designed for unattended operation or has a  
standby mode. Switch off by withdrawing the plug,  
make sure your family know how to do this. Special  
arrangements may need to be made for people  
with disabilities.  
Do  
read the operating instructions before you  
attempt to use the equipment.  
ensure that all electrical connections  
(including the mains plug, extension leads and  
inter-connections between pieces of equipment)  
are properly made and in accordance with the  
manufacturers’ instructions. Switch off and  
withdraw the mains plug before making or  
changing connections.  
continue to operate the equipment if you  
are in any doubt about it working normally, or it is  
damaged in any way – switch off, withdraw the  
mains plug and consult your dealer.  
ABOVE ALL NEVER let anyone, especially  
children, push or hit the screen, push  
anything into holes, slots or any other  
openings in the case.  
consult your dealer if you are ever in doubt  
about the installation, operation or safety of your  
equipment.  
NEVER guess or take chances with electrical  
equipment of any kind – it is better to be safe  
than sorry.  
be careful with glass panels or doors on  
equipment.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and important information  
Where to install  
Locate the television away from direct sunlight and strong  
lights, soft, indirect lighting is recommended for comfortable  
viewing. Use curtains or blinds to prevent direct sunlight  
falling on the screen.  
Sturdy tie  
(as short as possible)  
Place on a sturdy platform, the mounting surface should be  
flat and steady. It should then be secured to the wall with a  
sturdy tie using the clip on the back of the stand, or secured  
to the platform using the fixing strap located underneath the  
table top stand, this will prevent it from falling over.  
Clip  
Clip  
Clip  
The LCD display panels are manufactured using an  
extremely high level of precision technology, however  
sometimes some parts of the screen may be missing picture  
elements or have luminous spots. This is not a sign of a  
malfunction.  
Side View  
Top View  
Make sure the television is located in a position where it cannot be pushed or hit by objects, as pressure will break or  
damage the screen, and that small items cannot be inserted into slots or openings in the case.  
Please take note  
EXCLUSION CLAUSE  
Toshiba shall under no circumstances be liable for loss and/or damage to the product caused by:  
i) fire;  
ii) earthquake;  
iii) accidental damage;  
iv) intentional misuse of the product;  
v) use of the product in improper conditions;  
vi) loss and/or damage caused to the product whilst in the possession of a third party;  
vii) any damage or loss caused as a result of the owner’s failure and/or neglect to follow the instructions set out in the owner’s  
manual;  
viii) any loss or damage caused directly as a result of misuse or malfunction of the product when used simultaneously with  
associated equipment;  
Furthermore, under no circumstances shall Toshiba be liable for any consequential loss and/or damage including but not limited  
to the following, loss of profit, interruption of business, the loss of recorded data whether caused during normal operation or  
misuse of the product.  
If stationary images generated by text services, channel identification logos, computer displays, video games, on screen menus, etc.  
are left on the television screen for any length of time they could become conspicuous, it is always advisable to reduce both the  
brightness and contrast settings.  
Download from Www.Somanuals.co4m. All Manuals Search And Download.  
The remote controlUP  
Simple at-a-glance reference of your remote control.  
To mute the sound  
For On/Standby mode  
Number buttons  
To select input from external sources  
To return to the previous programme  
Selectable picture preferences  
To exit Menus  
Widescreen viewing  
On-screen Menus  
Navigation Ring:  
Use P and P to change programme  
f
e
positions and text pages  
Use jand j+ to alter the volume  
When using menus press up, down, left  
and right to move the cursor on the  
screen. OK to confirm your selection  
Text control buttons  
To select mode  
No function on this model  
No function on this model  
To display on-screen information  
Stereo/bilingual transmissions  
When using a TOSHIBA VCR or DVD:  
When in TV mode:  
/
Time display  
To call up text  
When in Text mode:  
8 9  
press  
/
to PAUSE/STEP  
ll  
r
m
/
/
6
7
press to PLAY  
r
press  
press  
press  
to REWIND  
q
To reveal concealed text  
r
q
s
to FAST FORWARD  
s
To hold a wanted page  
To enlarge text display size  
To select a page whilst viewing a  
normal picture  
to EJECT  
w
/
8 9  
press to STOP  
p
press  
press  
to SKIP-REWIND  
l
q
to SKIP-FORWARD  
l
s
Inserting batteries and effective range of the remote  
Remove the back cover to reveal the battery compartment and make sure the batteries are inserted  
the right way round. Suitable battery types for this remote are AAA, IEC R03 1.5V.  
Do not combine a used, old battery with a new one or mix battery types. Remove dead batteries  
immediately to prevent acid from leaking into the battery compartment. Dispose of them in a  
designated disposal area.  
The performance of the remote control will deteriorate beyond a distance of five metres or outside an  
angle of 30 degrees from the centre of the television. If the operating range becomes reduced the  
batteries may need replacing.  
Download from Www.Somanuals.co5m. All Manuals Search And Download.  
HtraDdMemI, athreksHoDrMreIgliostgeore, dantrdadHeigmha-DrkesfoinfitHioDnMMIuLlitcimenesdiniag,InLtLeCrf.aAceeriaarlecables:  
Cteolenvniseioctnt.hIef yaoeuriaulsetoathdeecsoodckeer*t oanndt/hoerraeamreodfitaherecorder  
itthies deessceondteiarlathnadt/othrethareoruiaglhctahbelemisedcoiannreeccoterddetrhtroouthgeh  
tSeCleAvRisTiolne.ads:  
Cteolenvniseioctnt.hCeovnidneeoctrtehceorddeecroIdNe/rOTVUTsoscokcektettotothtehe  
dteelecovidsieornM. CEoDnIAneRctEtCh.esomcekdetia. recorder SAT socket to the  
Before running Auto tuning put your decoder and media  
recorder to Standby.  
TINhPeUpThosoncokesotsckweiltlsaaclcoenpgtsLidaentdheRCaOudMioPOsigNnEaNlsT. VIDEO  
In addition there is a fixed/variable external audio ouput  
wmhaikceh seunraebtlhees tShpeecaoknenrecotpiotinontoinatshueitaSboluenHdi-mFieunnuit,is set  
ocofnOtrfof.lsT.he variable option is altered by using the sound  
g
g
COMPONENT  
VIDEO (EXT3)  
SCART 2 (EXT2)  
SCART 1 (EXT1)  
CABLE HOLDER  
FIXING STRAP  
MEDIA REC.  
decoder*  
TV  
HDMI™ INPUT SOCKETS  
IN/OUT  
SAT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6HCD  
with  
o
M
a
n
Inec(tHinigh teerfninailtiequiMpmuletinmtedia Interface) is for use  
DVD, decoder or electrical equipment with digital  
e
-
x
D
o
n
audio and video output. It is designed for best  
performance with 1080i high-definition video signals but  
will also accept and display 480i, 480p, 576i, 576p and  
720p signals.  
A
wide variety of external equipment can be  
connected to the back of the television, therefore  
the reblev fetrorwednetors. manuals for additionalequipment  
r
an  
e
We recommend SCART for decoder and SCART for  
1
a
2
a
media recorder.  
If conneotirng S-VIDEO equipment, set the INPUT  
f
c
EXT2. See page 22.  
If the television automatically switches over to monitor  
external equipment, return to normal television by  
pressing the desired programme position button. o  
T
recall external equipment, press Bto select between  
EXT1, EXT2, EXT3 (C), HDMI1, HDMI2 or P.  
C
The cable holder can be used for aerial, media recorder  
and audio cables. Do not use the cable holder as  
a
handle and make sure all cables are removed before  
moving the television.  
Connecting a computer  
7
Controls and input connections  
A wide variety of external equipment can be connected to the input sockets on the side of the television.  
Whilst all the necessary adjustments and controls for the television are made using the remote control, the  
buttons on the television may be used for some functions.  
INPUT 3  
(EXT3)  
GREEN LED – On timer  
RED LED – Power on  
Standby  
Switching on  
Using the controls and connections  
If the RED LED is unlit check that the mains plug is  
connected to the power supply. If the picture does not  
To alter the volume press –  
j
+.  
appear press  
few moments.  
on the remote control, it may take a  
To alter the programme position press e f.  
F
i
Press MENU and S, R, P or Q to control the sound  
and picture options.  
To put the television into Standby press  
on the remote  
again. The picture  
i
control. To view the television press  
i
may take a few seconds to appear.  
Press MENU to finish.  
To set up the television you will now need to use the  
on-screen menus. Press the MENU button on the  
remote control to see the menus.  
When connecting sound equipment to EXT3, connect  
the audio output of the equipment to the phono sockets  
on the television.  
The menu bar at the top of the screens will show five  
different topics shown in symbols. As each symbol is  
selected by pressing left or right on the navigation ring  
on the remote control, its respective options will appear  
below.  
To select the Input, press  
EXT3 as described on page 22. The television will  
automatically sense the type of signal.  
until the display shows  
B
Please always refer to the owner’s manual of the  
equipment to be connected for full details.  
To use the options, press down on the navigation ring to  
move down through them and OK, left or right to  
select the required choice. Follow the on-screen  
instructions. The functions of each menu are described in  
detail throughout the manual.  
Please note: Inserting the headphone plug will mute the  
sound from all speakers.  
Download from Www.Somanuals.co8m. All Manuals Search And Download.  
Tuning the television using Quick Setup,  
sorting programme positions  
Before switching on the television put your decoder and media recorder to Standby if they are connected.  
To set up the television use the buttons on the remote control as detailed on page 5.  
With the list of stations now showing use up or  
down to highlight the station you want to move  
and press right.  
Connect the television to the mains power. The  
Quick Setup screen will appear.  
6
1
Quick Setup  
The selected station will be moved to the right of  
the screen.  
Select your language.  
Manual tuning  
Language  
EXIT  
English  
Next  
Prog.  
1
Channel  
Station  
OK  
Watch TV  
C22  
BBC1  
2
3
4
C28  
C25  
C32  
BBC2  
ITV  
Using left or right select your language, then  
press OK.  
2
3
4
CH4  
5
6
C69  
C69  
Then press left or right to select your country  
and press OK.  
Store  
MENU  
EXIT  
Back  
Watch TV  
To start Auto tuning press OK.  
Use up or down to move through the list to your  
preferred position. As you do so the other stations  
will move to make room.  
Auto tuning  
Searching  
7
8
Channel  
EXIT  
:
C22  
Station : BBC1  
Stop  
Press right to store your move.  
Repeat as necessary, then press EXIT.  
The search will begin for all available stations.  
The slide bar will move along the line as the  
search progresses.  
5
If the television cannot be connected to a media  
recorder/decoder with a SCART lead or if a  
station on another  
is required, use  
Manual tuning to allocate a programme  
position, see page 10.  
When the search is complete the television will  
automatically select programme position 1. This  
may not be a clear picture or the signal may be  
weak, so the station order can be changed using  
Manual tuning which will appear on the screen.  
Manual tuning  
Prog.  
1
Channel  
Station  
C22  
BBC1  
2
3
C28  
C25  
BBC2  
ITV  
4
5
6
C32  
C69  
C69  
CH4  
OK  
Select  
Back  
Sort  
EXIT  
MENU  
Watch TV  
Download from Www.Somanuals.co9m. All Manuals Search And Download.  
Manual tune  
The television can be tuned-in manually using Manual tuning. For example: if the television cannot be  
connected to a media recorder/decoder with a SCART lead or to tune-in a station on another System.  
Use  
and  
to move across the screen and select any of these Manual Tune options.  
Programme  
skip  
Programme  
System  
Colour  
system  
Channel Search Manual fine  
tuning  
Station  
Programme: The number to be pressed on the remote control.  
System: Specific to certain areas.  
Colour system: Factory set to Auto, should only be changed if problems are experienced, i.e. NTSC input from  
external source.  
Programme skip:  
Channel: The channel number on which a station is being broadcast.  
Search: Search up and down for a signal.  
means nothing has been stored or the facility to skip the channel is ON. See page 11.  
Manual fine tuning: Only used if interference/weak signal is experienced. See page 26.  
Station: Station identification. Use up or down and left or right to enter up to seven characters.  
To allocate a programme position on the television for a decoder and media recorder: turn the decoder on,  
insert a pre-recorded film in the media recorder and press PLAY, then manually tune.  
Press MENU and using left or right select the  
SET UP menu, with down highlight Manual  
tuning, press OK to select.  
Press OK to select. If the programme is skipped,  
Programme skip must be removed before  
storing.  
1
3
Manual tuning  
System  
0
I
A
C
60  
0
SET UP  
1/2  
OK  
Store  
Back  
Language  
English  
MENU  
EXIT  
Watch TV  
Country  
UK  
OK  
OK  
OK  
OK  
Press right to select System and use up or down  
to change if required.  
Auto tuning  
Manual tuning  
AV connection  
Picture position  
4
Then press right to select Search.  
5
6
MENU  
Back  
EXIT  
Watch TV  
Press up or down to begin the search. The  
search symbol will flash.  
Use up or down to highlight the programme  
2
position required e.g. we suggest  
for  
Manual tuning  
Search: Up  
a media recorder.  
0
I
A
C
60  
0
Manual tuning  
OK  
Store  
Back  
MENU  
EXIT  
Prog.  
0
Channel  
Station  
Watch TV  
C60  
1
2
3
C22  
C28  
C25  
BBC1  
BBC2  
ITV  
Each signal will show on the television, if it is not  
your media recorder, press up or down again to  
restart the search.  
7
4
5
C32  
C69  
CH4  
OK  
Select  
Sort  
MENU  
EXIT  
Back  
Watch TV  
Download from Www.Somanuals.c1om0. All Manuals Search And Download.  
Manual tune  
continued,  
Programme skip  
When your media recorder signal is found, press  
8
Programme skip  
left to move along to Station. With up, down,  
left and right put in the required characters,  
e.g. VCR.  
To prevent certain programmes from being viewed, the  
programme position can be skipped. The remote control  
must be removed as the channels will still be available using  
the number buttons. Programmes can then be watched as  
normal using the controls on the television, but the television  
will not show the skipped programme position.  
Manual tuning  
Station  
0
I
A
C
60  
0
V
C
R
OK  
Store  
Back  
MENU  
EXIT  
Watch TV  
Select Manual tuning from the SET UP menu.  
1
Press OK to store.  
Manual tuning  
9
Prog.  
0
Channel  
Station  
Repeat for each  
you want  
C60  
VCR  
10  
to tune or, press MENU to return to the list of  
channels and select the next number to tune.  
1
2
3
C22  
C28  
C25  
BBC1  
BBC2  
ITV  
Press EXIT when you have finished.  
11  
12  
4
5
C32  
C69  
CH4  
To name external equipment, e.g. DVD on EXT2,  
press  
to select EXT2, then select Manual  
B
OK  
Select  
Back  
Sort  
EXIT  
setting from the SET UP menu.  
MENU  
Watch TV  
Press right to select Label then using up, down,  
left and right put in the required characters.  
13  
Use up or down to highlight the programme  
position to be skipped and press OK to select.  
2
Manual setting  
Label  
Press right to select Programme skip.  
3
4
EXT2  
Store  
A
D
V
D
Use up or down to turn Programme skip on.  
Press OK.  
OK  
MENU  
EXIT  
Back  
Watch TV  
on the screen indicates a skipped  
programme position.  
At any time by pressing OK a list will appear on  
screen showing all stored programmes and  
external equipment. Use up and down to  
highlight and OK to select.  
14  
Manual tuning  
Programme skip : On  
1
I
A
C
22  
0
B
B
C
1
OK  
PC  
HDMI2  
HDMI1  
Store  
Back  
MENU  
EXIT  
Watch TV  
Press MENU and repeat from  
EXIT.  
or press  
3C  
2
1
B
5
DVD  
B
B
4
Each programme position has to be individually  
selected. To turn Programme skip off, repeat the  
procedure for each position.  
CH4  
ITV  
BBC2  
3
2
Skipped programme positions  
be selected  
by P and P or by the controls on the  
f
e
This television has direct channel entry  
if the channel numbers are known.  
PLEASE NOTE  
television, but  
still be accessed by the number  
buttons on the remote control.  
Select the Manual tuning screen in  
. Enter the  
Programme number, the System, then the  
Channel number. Press OK to store.  
Download from Www.Somanuals.c1om1. All Manuals Search And Download.  
Auto tune, general controls, sound controls  
Using Auto tuning  
Selecting programme positions  
To select a programme position use the numbered  
buttons on the remote control.  
To set up the television using Auto tuning, press  
MENU and use left or right to select the SET UP  
menu.  
1
Programme positions can also be selected using P and  
f
P
.
e
To revert to the previous programme position press  
.
^
SET UP  
1/2  
To display on-screen information i.e. programme position,  
Language  
English  
+
input mode or stereo/mono signal, press  
again to cancel.  
. Press  
Country  
UK  
OK  
OK  
OK  
OK  
Auto tuning  
Manual tuning  
AV connection  
Picture position  
Sound controls  
MENU  
Back  
EXIT  
Watch TV  
Volume  
Press  
j
or  
j
+ to adjust the volume.  
Press down to highlight Language and left or  
right to select.  
2
3
Sound Mute  
Press  
once to turn the sound off and again to cancel.  
k
Using down highlight Country, then left or right  
to select. The television will now tune the stations  
for your country.  
Bass, Treble and Balance  
Press down to highlight Auto tuning, then press  
4
OK.  
Auto tuning  
SOUND  
1/2  
!
Previous settings will be lost  
Press EXIT for no change.  
Press OK to start Auto tune.  
!
Dual  
Dual 1  
Bass  
0
0
0
Treble  
Balance  
WOW  
MENU  
EXIT  
Back  
Watch TV  
OK  
On  
Stable sound  
To start Auto tuning press OK.  
5
MENU  
EXIT  
Back  
Watch TV  
Press MENU and left or right to select SOUND.  
1
2
When the search is complete the television will  
automatically select programme position 1. This may not  
be a clear picture, so the station order can be changed  
using Manual tuning, see page 9.  
Press down to highlight Bass, Treble or Balance  
and left or right to change the setting.  
Download from Www.Somanuals.c1om2. All Manuals Search And Download.  
Sound controls  
continued,  
SRS WOW™ sound  
effects, dual, stable sound®  
WOW  
SRS 3D  
On  
FOCUS  
TruBass  
Off  
Off  
MENU  
EXIT  
Back  
Watch TV  
Press down to highlight SRS 3D and using  
left or right select between On or Off.  
3
4
5
Then press down to highlight FOCUS and press  
left or right to select between On or Off.  
Highlight TruBass and use left or right to select  
Off, Low or High to suit your preference.  
NOTE: This feature is not available through  
headphones.  
Dual  
If a programme or film is being broadcast with a  
soundtrack in more than one language, the DUAL feature  
allows selection between them.  
When connecting to a Hi-fi unit, set the Speaker option  
to Off. Then select Fixed or Variable for the Monitor  
(Audio) in the AV connection menu.  
Press MENU and select the SOUND menu.  
1
Use down to highlight Dual then press left or  
right to choose between Dual 1 or Dual 2.  
2
(See 'Input Selection and AV Connections' section).  
SRS WOWsound effects  
Stable sound®  
SRS WOW™ is a suite of audio effects which use the  
stereo signals being broadcast to produce enhanced sound  
from the television’s speakers. If mono sound is broadcast  
only TruBass will be available.  
The Stable Sound feature limits high volume levels and  
prevents the extreme changes in volume that can occur  
when channels are changed or a programme switches to  
a commercial.  
gives a rich sound experience,  
concentrates the sound and gives the effect of it coming  
Press MENU and select the SOUND menu.  
1
from the centre of the television,  
lower bass frequencies.  
enhances the  
Use down to highlight Stable Sound then press  
left or right to select On or Off.  
2
Press MENU and select the SOUND menu.  
1
2
Use up or down to highlight WOW then press  
OK.  
WOW, SRS and   
symbol are trademarks of SRS Labs, Inc.  
WOW technology is incorporated under license from SRS Labs, Inc.  
13  
Widescreen viewing  
Depending on the type of broadcast being transmitted, programmes can be viewed in a number of formats.  
Press the  
button repeatedly to select between Exact Scan, Wide, Super Live 2, Cinema 2, 4:3, Super  
{
Live 1, Cinema 1, Subtitle and 14:9. Please note: Whenever the MENU button is pressed the picture size  
settings will change while the menus are ON the screen. This is to ensure the menus do not overlap the  
edges of the viewable area.  
This setting will enlarge a 4:3 image to  
fit the screen by stretching the image  
horizontally and vertically, holding the  
correct proportions at the centre of the  
image. Some distortion may occur.  
If a ‘side panel format’ signal is being  
received this setting will enlarge the  
image to fit the screen by stretching  
the image horizontally and vertically,  
holding the correct proportions at the  
centre of the image. Some distortion  
may occur.  
When watching ‘letterbox format’  
films/video tapes, this setting will  
eliminate or reduce the black bars at  
the top and bottom of the screen by  
zooming in and selecting the image  
without distortion.  
When watching ‘all sides panel format’  
films/video tapes, this setting will  
eliminate or reduce the black bars at all  
sides of the screen by zooming in and  
selecting the image without distortion.  
When subtitles are included on a  
letterbox format broadcast, this setting  
will raise the picture to ensure that all  
the text is displayed.  
SUBTITLE  
Download from Www.Somanuals.c1om4. All Manuals Search And Download.  
Widescreen viewing  
continued  
Use this setting when watching a 14:9  
broadcast.  
Use this setting when watching a  
widescreen DVD, widescreen video  
tape or a 16:9 broadcast  
(when available). Due to the range of  
widescreen formats (16:9, 14:9,  
20:9 etc.) black bars may be visible  
on the top and bottom of the screen.  
Use this setting to view a true 4:3  
broadcast.  
42 MODEL ONLY  
Use this setting when watching a  
1080i source, it will display the image  
as transmitted without scaling or  
cropping the picture.  
Exact Scan  
Wide  
Press and hold the  
button and a list of all the widescreen formats will appear on  
{
screen. Use up and down to highlight the required format and OK to select.  
Super Live 2  
Cinema 2  
4:3  
Super Live 1  
Cinema 1  
Subtitle  
14:9  
Using the special functions to change the size of the displayed image (i.e. changing the height/width ratio) for the purposes of public display or  
commercial gain may infringe on copyright laws.  
Download from Www.Somanuals.c1om5. All Manuals Search And Download.  
Picture controls  
Picture position  
Back light  
The picture position may be adjusted to suit personal  
preference and can be particularly useful for  
external inputs.  
Adjusting the Back light can improve the clarity of the  
screen when viewing.  
In the PICTURE menu press down to select  
Picture settings, then press OK.  
1
In the SET UP menu press down until  
Picture position is highlighted.  
1
PICTURE  
Picture settings  
SET UP  
Language  
1/2  
OK  
Off  
English  
3D Colour management  
Base colour adjustment  
Cinema mode  
Country  
UK  
OK  
OK  
OK  
OK  
Auto tuning  
Manual tuning  
AV connection  
Picture position  
Off  
MENU  
EXIT  
Back  
Watch TV  
MENU  
EXIT  
Back  
Watch TV  
In the Picture settings menu press down to  
select Back light.  
2
3
Press OK to view the options available for the  
picture format that has been selected.  
2
3
Press left or right to adjust.  
Press up and down to select an option, then left  
or right to adjust the settings.  
Picture settings  
1/2  
Back light  
100  
The options alter depending on the widescreen  
format chosen and when viewing connected  
equipment.  
Contrast  
Brightness  
Colour  
100  
50  
50  
0
In Cinema 2:  
Tint  
Sharpness  
0
Picture position  
MENU  
Back  
EXIT  
Watch TV  
Horizontal position  
Vertical position  
Reset  
0
0
OK  
MENU  
Back  
EXIT  
Watch TV  
To return to the original factory settings select Reset  
in the Picture position menu and press OK.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture controls  
continued  
Picture preferences  
MPEG NR – Noise Reduction  
This television offers the choice of personalising the picture  
style. Press to view the different styles available:  
When watching a DVD the compression may cause some  
words or picture elements to become distorted or pixelated.  
Using the MPEG NR feature reduces this effect by  
smoothing out the edges.  
m
Picture mode-1 to 3 are preset options and  
Picture mode-M stores your own settings:  
Select MPEG NR from the Picture settings  
menu. Use left or right to select a setting to suit  
your preference.  
1
Select Picture settings from the PICTURE menu.  
1
Picture settings  
1/2  
Back light  
100  
Picture settings  
2/2  
Contrast  
Brightness  
Colour  
100  
50  
50  
0
Black stretch  
On  
MPEG NR  
Middle  
Auto.  
DNR  
Tint  
Colour Temperature  
Normal  
Sharpness  
0
MENU  
Back  
EXIT  
Watch TV  
MENU  
Back  
EXIT  
Watch TV  
Use left or right to adjust the Contrast,  
2
Brightness, Colour, Tint and Sharpness.  
DNR – Digital Noise Reduction  
Black stretch  
DNR enables you to ‘soften’ thescreen representation of a  
weak signal to reduce the noise effect.  
Black Stretch increases the strength of dark areas of the  
picture which improves the definition.  
Select DNR from the Picture settings menu. Use  
1
left or right to adjust. The differences may not  
always be noticeable (for the best result use lower  
settings as picture quality can be lost if the setting  
is too high).  
In the Picture settings menu press down until  
Black Stretch is highlighted.  
1
Picture settings  
2/2  
Picture settings  
2/2  
Black stretch  
On  
Black stretch  
On  
MPEG NR  
Off  
DNR  
Auto.  
MPEG NR  
Off  
Colour Temperature  
Normal  
DNR  
Middle  
Normal  
Colour Temperature  
MENU  
Back  
EXIT  
Watch TV  
MENU  
Back  
EXIT  
Watch TV  
Press left or right to select between Onand Off.  
The effect depends on the broadcast and is most  
noticeable on dark colours.  
2
Download from Www.Somanuals.c1om7. All Manuals Search And Download.  
Picture controls  
continued  
Base colour adjustment  
Colour temperature  
The Base colour adjustment feature allows the  
adjustment of individual colours to suit personal  
preference. This can be useful when using an  
external source.  
Colour Temperature increases the ‘warmth’ or ‘coolness’  
of a picture by increasing the red or blue tint.  
In the Picture settings menu press down until  
Colour Temperature is highlighted.  
1
In the PICTURE menu press down to select  
Base colour adjustment, then press OK.  
1
Picture settings  
2/2  
Black stretch  
On  
MPEG NR  
Off  
DNR  
Auto.  
PICTURE  
Colour Temperature  
Normal  
Picture settings  
OK  
On  
OK  
Off  
3D Colour management  
Base colour adjustment  
Cinema mode  
MENU  
Back  
EXIT  
Watch TV  
Press left or right to select between Normal,  
Warm and Cool to suit your preference.  
2
MENU  
EXIT  
Back  
Watch TV  
Press up and down to select an option, then  
right to adjust the settings.  
2
3D Colour management  
Base colour adjustment  
When 3D Colour management is selected it allows the  
‘Base colour adjustment’ feature to become available.  
Hue  
+2  
Saturation  
+6  
Brightness  
+4  
Red  
Green  
0
0
0
In the PICTURE menu press down to select  
3D Colour management.  
1
Blue  
0
0
0
0
0
0
Yellow  
Magenta  
Cyan  
0
0
0
0
0
0
Reset  
MENU  
OK  
PICTURE  
EXIT  
Back  
Watch TV  
Picture settings  
OK  
On  
OK  
Off  
3D Colour management  
Base colour adjustment  
Cinema mode  
To return to the original factory settings select  
Reset and press OK.  
MENU  
EXIT  
Back  
Watch TV  
Press left or right to select On or Off.  
2
Download from Www.Somanuals.c1om8. All Manuals Search And Download.  
Picture controls  
continued  
Cinema mode  
Blue screen  
If there are lines or jagged edges in the film or programme  
being viewed, selecting Cinema mode can help correct  
this by smoothing out the picture.  
When Blue screen is selected the screen will turn blue and  
the sound will be muted when no signal is received.  
In the FUNCTION menu press down to highlight  
Blue screen.  
1
In the PICTURE menu press down to select  
Cinema mode.  
1
FUNCTION  
PICTURE  
Teletext  
Auto.  
Picture settings  
OK  
Off  
Panel lock  
Auto format  
Blue screen  
Side Panel  
Off  
On  
On  
1
3D Colour management  
Base colour adjustment  
Cinema mode  
On  
MENU  
Back  
EXIT  
MENU  
EXIT  
Watch TV  
Back  
Watch TV  
Press left or right to select On or Off.  
Press left or right to select On or Off.  
2
2
Automatic format (Widescreen)  
Side panel adjustment  
When this television receives a true Widescreen picture and  
Auto format is On, it will automatically be displayed in  
Widescreen format, irrespective of the  
The Side Panel feature lightens or darkens the band each  
side of the screen when in 4:3 or 14:9 format. This helps  
prevent image retention of the band and can also make  
viewing in bright or dark conditions more comfortable.  
television’s previous setting.  
Press MENU and left or right to select the  
FUNCTION menu.  
1
In the FUNCTION menu press down until Side  
Panel is highlighted.  
1
FUNCTION  
FUNCTION  
Teletext  
Auto.  
Teletext  
Auto.  
Panel lock  
Auto format  
Blue screen  
Side Panel  
Off  
On  
On  
1
Panel lock  
Auto format  
Blue screen  
Side Panel  
Off  
On  
On  
1
MENU  
Back  
EXIT  
Watch TV  
MENU  
Back  
EXIT  
Watch TV  
Press down to highlight Auto format, then left  
or right to select On or Off.  
2
Press left or right to adjust.  
2
Download from Www.Somanuals.c1om9. All Manuals Search And Download.  
Panel lock, time display,  
stereo/bilingual transmissions, the timer  
Panel lock  
The Timer  
disables the buttons on the television. All  
buttons on the remote control can still be used.  
The television can be set to turn itself On or Off after a  
certain time.  
From the FUNCTION menu select Panel lock  
and choose On or Off usingleft or right.  
Press MENU and left or right to select the TIMER  
menu.  
1
1
FUNCTION  
TIMER  
Teletext  
Auto.  
Sleep timer  
01:30  
Panel lock  
Auto format  
Blue screen  
Side Panel  
On  
On  
On  
1
On timer  
00:00  
01  
On timer Position  
MENU  
Back  
EXIT  
Watch TV  
MENU  
Back  
EXIT  
Watch TV  
When Panel lock is On, a reminder will appear when  
the buttons on the television are pressed. If the standby  
button is pressed the television will switch off and  
can only be brought out of standby by using the  
remote control.  
Press down to select On or Sleep timer. Use the  
number buttons to set the required time. For  
example, to switch the television off in one and a  
half hours enter 01:30, or press right to  
2
3
increase/decrease in steps of 10 minutes.  
If setting the Sleep timer, press EXIT to finish. If  
setting the On timer, press down to select On  
timer Position, enter the programme position  
The Time Display  
number required, then press  
to put the  
i
The time display facility allows the current (text service)  
time to be seen on the television screen.  
television into Standby. The GREEN On timer  
indicator on the front of the television will now  
be lit.  
/
Press  
whilst watching a normal television  
8 9  
broadcast to see a time display from the broadcaster. It  
will remain on screen for about 5 seconds.  
Any equipment connected with SCART leads must  
also be put into Standby to prevent them from  
being displayed when the timer switches on.  
Once the On timer has been set the television  
Stereo and Bilingual transmissions  
can be switched on at any time by pressing  
.
i
The Green On timer indicator will remain on until  
the set time period as passed when the television  
will go to the chosen channel. This feature can  
help to avoid missing favourite programmes.  
If stereo or dual language broadcasts are transmitted the  
word Stereo or Dual will appear on the screen each time  
programme positions are changed, disappearing after a  
few seconds. If the broadcast is not in stereo the word  
Mono will appear.  
To cancel the On timer/Sleep timer, enter zero  
in each position.  
4
Stereo… Press O  
to select Stereo or Mono.  
Bilingual… Bilingual transmissions are rare. If they are  
transmitted the word Dual will display. Choose the  
required programme number and if the word Dual  
appears press O  
to select Dual 1, Dual 2 or Mono.  
Download from Www.Somanuals.c2om0. All Manuals Search And Download.  
PC settings – picture position, clock phase,  
sampling clock, reset  
Picture position  
Sampling clock  
The picture position may be adjusted to suit personal  
preference.  
Adjusting the Sampling clock alters the number of pulses  
per scan, this will clear vertical lines on the screen.  
Press  
to select PC, then select PC Setting  
B
In the SET UP menu press down until PC Setting  
is highlighted.  
1
1
from the SET UP menu.  
Press OK to select, then down to highlight  
Sampling clock.  
2
SET UP  
PC Settings  
1/2  
Language  
English  
Horizontal position  
Horizontal width  
Vertical position  
Vertical height  
Clock phase  
0
–5  
0
Country  
UK  
OK  
OK  
AV connection  
PC Setting  
–5  
0
Sampling clock  
0
MENU  
Back  
EXIT  
Watch TV  
MENU  
Back  
EXIT  
Watch TV  
Press OK. Press up and down to select an option,  
then left or right to adjust the settings.  
2
Use left or right to adjust until the picture clears.  
3
PC Settings  
1/2  
Reset  
Horizontal position  
Horizontal width  
Vertical position  
Vertical height  
Clock phase  
0
–5  
0
To return to the original factory settings.  
–5  
0
In the SET UP menu press down until PC Setting  
is highlighted.  
1
2
Sampling clock  
0
Press OK to select, then down to highlight Reset.  
MENU  
Back  
EXIT  
Watch TV  
PC Settings  
2/2  
Reset  
OK  
Clock phase  
The Clock phase matches the PC signal with the LCD  
display. Adjusting this can clear horizontal stripes and  
picture blur.  
MENU  
EXIT  
Back  
Watch TV  
In the SET UP menu press down until PC Setting  
1
is highlighted.  
Press OK.  
3
Press OK to select, then down to highlight Clock  
2
3
phase.  
Use left or right to adjust until the picture clears.  
Download from Www.Somanuals.c2om1. All Manuals Search And Download.  
Input selection and  
AV connections  
Defining the INPUT and OUTPUT sockets so that the television recognises connected equipment. See page 6  
for a clear view of the back connection recommendations.  
Most media recorders and decoders send a signal  
through the SCART lead to switch the television to the  
correct Input socket.  
INPUT signal selection  
This specifies the type of signal going into SCART 2 (  
Alternatively press the external source selection button  
)
on the back of the television. Please refer to the  
until the picture from connected equipment is shown.  
B
manufacturers instructions for the connected equipment.  
This button must be used to view equipment connected  
using the COMPONENT VIDEO INPUT (EXT3C).  
In the SET UP menu press down until  
1
AV connection is highlighted, then press OK.  
An S in the display e.g. 2S (EXT 2S), indicates the  
B
input is set for an S-Video signal.  
SET UP  
1/2  
Input selection  
Language  
English  
Country  
UK  
OK  
OK  
OK  
OK  
Use the Input Selection if the television does not switch  
over automatically.  
Auto tuning  
Manual tuning  
AV connection  
Picture position  
Press  
to select  
1,  
2,  
3(C) (EXT1-3),  
B
B B B  
1
HDMI1, HDMI2 or PC.  
MENU  
Back  
EXIT  
Watch TV  
HDMI™ displays equipment connected to Input  
HDMI on the back of the television. It is designed  
for best performance with 1080i high definition  
signals.  
With left or right select either AV or S-VIDEO as  
2
the required  
for EXT2.  
PC displays a computer connected to Input  
AV connection  
RGB/PC on the back of the television.  
PC/HDMI1 audio  
PC  
HDMI1 audio  
EXT2 input  
Digital  
S-VIDEO  
Fixed  
To return to television mode press  
one of the numbered buttons.  
again or  
B
2
Monitor (Audio)  
MENU  
Back  
EXIT  
Watch TV  
If the colour is missing try the alternative setting.  
Download from Www.Somanuals.c2om2. All Manuals Search And Download.  
SET UP  
1/2  
Language  
English  
Country  
UK  
OK  
OK  
OK  
OK  
Auto tuning  
Manual tuning  
AV connection  
Picture position  
MENU  
Back  
EXIT  
Watch TV  
Text services – setting up,  
general information, Auto and LIST modes  
This television has a multi-page text memory, which takes a few moments to load. It offers two  
of  
viewing text – Auto will display Fastext, if available. LIST will store your four favourite pages.  
The sub-page you are viewing will be highlighted and, as  
the television loads any additional sub-pages the colour  
of the numbers will change, indicating that these pages  
have been loaded.  
Selecting modes  
The text character set will be automatically chosen by the  
language setting in the SET UP menu.  
These sub-pages will remain available to view until  
another page is chosen or, in normal TV mode, the  
channel is changed.  
Select Teletext from the FUNCTION menu.  
1
With left or right choose Auto. or LIST then press  
EXIT.  
2
Navigating pages using Auto.  
If Fastext is available four coloured titles will appear at  
the base of the screen.  
FUNCTION  
To access one of the four given subjects, press the  
relevant coloured button on the remote control.  
Teletext  
Auto.  
Panel lock  
Auto format  
Blue screen  
Side Panel  
Off  
On  
On  
1
For further information on your particular text system(s),  
see the broadcast text index page or, consult your local  
Toshiba dealer.  
MENU  
Back  
EXIT  
Watch TV  
Navigating pages using LIST  
The four coloured choices at the bottom of the screen are  
numbers – 100, 200, 300 and 400, which have been  
programmed into the television’s memory. To view these  
pages press the relevant coloured buttons.  
Text information  
/
/
The  
button:  
6 7  
/
/
To view text services press  
. Press again to  
6 7  
To change these stored pages press the relevant coloured  
button and enter the 3 digit number. This number will  
change in the top left of the screen and in the coloured  
highlight.  
superimpose the text over a normal broadcast picture and  
again to return to normal viewing. Programmes cannot  
be changed until text is cancelled.  
The first text page shown will be the initial page.  
Press OK to store. The bars at the bottom of the screen  
will flash white. Whenever OK is pressed all four  
page numbers showing at the bottom will be stored  
and the previous ones will be lost.  
Any text page can be accessed by entering the 3 digit  
page number using the numbered buttons, pressing the  
coloured buttons or pressing P to advance to the next  
f
page and P to go back to the previous page.  
e
If OK is not pressed the selection will be forgotten when  
text is cancelled.  
Sub-pages  
If there are sub-pages they will automatically load into  
memory without changing the page on screen.  
Other pages may be viewed by entering the 3 digit page  
number – but DO NOT press OK or these pages will be  
stored.  
To access the sub-pages press  
then use P and  
f
X
P
to view them. A bar with numbers will appear on the  
e
side of the screen.  
Download from Www.Somanuals.c2om4. All Manuals Search And Download.  
Text services  
continued  
– control buttons  
Below is a guide to the functions of the remote control text buttons.  
To select a page whilst viewing a  
To display the index/initial page:  
/
T
89 normal picture:  
Press  
to access the index/initial page. The one  
displayed is dependant on the broadcaster.  
T
/
Enter the page number then press  
, a normal  
8 9  
picture will be displayed. The television will indicate when  
the page is present by displaying the page number at the  
/
/
top of the screen. Press  
to view the page.  
6 7  
To display a page of text:  
/
/
6 7  
To display news flashes:  
Select the news flash page for the chosen text service  
/
. The  
/
/
Press  
to display text. Press again to  
(see the index page of text service). Press  
news flashes will be displayed as and when they are  
8 9  
6 7  
superimpose text over a normal broadcast picture. Press  
again to return to normal television viewing. Programmes  
cannot be changed until this has been done.  
/
broadcast. Press  
again to cancel the display.  
8 9  
The news flash page must be cancelled before  
changing programmes.  
To access sub-pages:  
X
For use with P and P to view sub-pages when  
f
e
available.  
To reveal concealed text:  
r
To discover the solutions on quiz and joke pages press the  
button.  
r
To hold a wanted page:  
q
At times it is convenient to hold a page of text. Press  
q
and  
will appear in the top left of the screen. The  
q
page will be held on screen until the button is pressed  
again.  
To enlarge the text display size:  
s
Press  
once to enlarge the top half of the page, press  
again to enlarge the bottom half of the page. Press again  
to revert to normal size.  
s
Download from Www.Somanuals.c2om5. All Manuals Search And Download.  
tch  
TV  
a
W
EXIT  
Back  
MENU  
Store  
OK  
1
C
B
B
2
+
2
2
C
A
I
1
Manual fine tuning  
Manual tuning  
and  
adjust  
until  
the  
l.ines  
Settingfrom  
the  
clear  
may  
need  
adjustment.  
SelectPC  
the  
SET  
UP  
menu,  
highlightSampling  
clock  
when  
in  
PC  
mode?Q  
Below are the answers to some of the most common queries.  
For more information go to www.toshiba.co.uk  
Why is the VCR/DVD picture in black and  
white?  
Why is there no sound or picture?  
Q
Q
A
Check the mains switch is on and check all mains  
connections.  
Check the correct  
has been chosen,  
A
S-VIDEO or AV. See AV connections page.  
Check the television is not in standby mode.  
There is a picture, but why is there little or no  
colour?  
Q
When using an external source, for instance, a  
poor quality video tape, if there is little or no  
A
colour, improvements may sometimes be achieved. The  
colour is factory set to Auto. to automatically display the  
best colour system.  
To check that you have the best colour:  
With the external source playing, select Manual  
setting from the SET UP menu.  
1
Why don’t the controls on the front of the  
television work?  
Q
A
Check that Panel lock is not ON.  
With up or down choose between Auto., PAL,  
SECAM, NTSC 4. 43 or 3. 58.  
2
Why doesn’t the video/DVD being played show  
on screen?  
Q
Make sure the VCR or DVD player is connected to  
the television as shown on page 6, then select the  
A
correct input by pressing  
.
B
Why is there a message permanently on the  
screen?  
Q
A
Why is there a good video picture but no sound?  
Q
A
Q
A
Remove it by pressing  
+
.
Check all lead connections.  
Why is there a picture but no sound?  
Check the volume has not been turned down or  
that sound mute has not been selected.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AWhy  
Theare  
Satmhepreling  
verticalo  
l
ck  
stripes  
on  
screen  
Questions and Answers  
continued  
Why are there horizontal stripes and/or blurred  
Why are the four coloured text numbers visible  
but no text?  
Q
The Clock phase may need adjustment. Select  
PC Setting from the SET UP menu, highlight  
Clock phase and adjust until the picture clears.  
Text has been selected whilst viewing an external  
source i.e. DVD or VCR. No text will appear on  
screen or a box may appear stating no information is  
available. Select a broadcasting channel and press  
A
A
/
/
7
to access.  
6
Why are the colours wrong when an NTSC  
source is played?  
Q
Connect the source via a SCART lead and play.  
A
Select Manual setting from the SET UP menu.  
Why are there problems with text?  
Q
A
Manual setting  
Colour system: Auto.  
Good performance of text depends on a good  
strong broadcast signal. This normally requires a  
EXT2  
Store  
A
V
C
R
roof or loft aerial. If the text is unreadable or garbled,  
check the aerial. Go to the main index page of the text  
service and look for the User Guide. This will explain the  
basic operation of text in some detail. If further information  
is needed on how to use text see the text section.  
OK  
MENU  
EXIT  
Back  
Watch TV  
Set the Colour to Auto. and exit.  
1
2
Why are there no text sub-pages?  
Go to the Picture settings menu and adjust  
the tint.  
Q
There are none broadcast or they have not yet  
A
loaded. Press the  
(See text section).  
button to access.  
X
Cleaning the screen and cabinet…  
Turn off the power, clean the screen and cabinet with a soft, dry cloth. We recommend that you  
solvents on the screen or cabinet as this may cause damage.  
use any proprietary polishes or  
Disposal…  
The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is  
disposed of correctly, you will help prevent potential negative consequences for the environment and human health,  
which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about  
recycling of this product, please contact your local city office, your household waste disposal service or the shop where  
you purchased the product.  
27  
Specifications and accessories  
Stereo  
Nicam  
Broadcast systems/channels  
2 carrier system  
PAL-I  
UHF UK21-UK69  
Visible Screen Size  
(approx.)  
Model 26  
66cm  
80cm  
94cm  
107cm  
PAL-B/G  
UHF E21-E69  
VHF E2-E12, S1-S41  
32  
37  
42  
SECAM-L  
UHF F21-F69  
VHF F1-F10, B-Q  
Display  
16:9  
SECAM-D/K UHF R21-R69  
VHF R1-R12  
Sound output (at 10% distortion) Main 10W + 10W  
Power consumption  
as specified in  
EN60107-1 : 1997  
Model 26  
129W  
153W  
161W  
245W  
Video Input  
PAL, SECAM, NTSC 3.58/4.43  
32  
37  
42  
External connections  
EXT1  
EXT2  
EXT3  
Input  
Input  
Input  
21-pin SCART  
21-pin SCART  
RGB, A/V  
Standby (approx.)  
Model 26  
<1W  
<1W  
<1W  
<1W  
A/V, S-video  
32  
37  
42  
Phono jacks  
Phono jacks  
Y, PB/CB, PR/CR  
A/V  
Dimensions Model 26 54cm (H) 66cm (W) 28cm (D)  
EXT3  
Input (Side)  
Phono jack  
Phono jacks  
Video  
Audio L + R  
(approx.)  
32  
37  
42  
61cm (H) 80cm (W) 30cm (D)  
69cm (H) 92cm (W) 30cm (D)  
78cm (H) 105m (W) 36cm (D)  
HDMI 1/2 Input  
PC Input  
HDMI connector  
(Height dimension includes foot stand)  
Mini D-sub 15-pin Analog RGB signal  
Weight (approx.)  
Model 26  
15kg  
19kg  
25kg  
33kg  
32  
37  
42  
PC/HDMI1 Audio  
Phono jacks  
Phono jacks  
Audio L + R  
Audio L + R  
Audio Ouput Fixed/Variable  
Headphone socket  
Accessories  
3.5mm stereo  
Remote control  
2 batteries  
(AAA, IEC R03 1.5V)  
© Toshiba Information Systems (U.K.) Limited  
Printed on recycled paper. 100% Chlorine free.  
All rights reserved.  
Reproduction in whole or part without written permission is strictly prohibited.  
Toshiba Information Systems (U.K.) Limited  
Consumer Products Division,  
European Service Centre,  
Admiralty Way, Camberley,  
Surrey, GU15 3DT, UK  
26/32/37/42WL/  
EL/DL66/67  
Specification is subject to change without notice.  
Originated by Kensa Creative Solutions, Saltash, Cornwall.  
VX1A000012A0  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Tektronix Sander TDS5000B Series User Manual
TERK Technologies Network Card XMDGM100 User Manual
Toshiba Dehumidifier TRANQUILITY 20 User Manual
Trane Thermostat BMTK SVN01D EN User Manual
Tricity Bendix Cooktop SIE326 User Manual
Tripp Lite Power Supply 2U Tower Stand User Manual
Tyco Scanner S3010 User Manual
Uniden Scanner BC 245XLT User Manual
Viking Refrigerator F20394E EN User Manual
Villaware Food Processor NDVLFP1000 User Manual