Tecra 780CDM / 780DVD Disassembly Overview
The information offered in this section is an overview of the Maintenance Manual, Chapter 4, Replacement
Procedures. If you have any questions or concerns regarding the proper procedure please refer to the Mainte-
nance Manual through the Toshiba Service and Support Website before you proceed.
This section explains how to remove Field
Replaceable Units (FRUs). It may not be neces-
sary to remove all the FRUs in order to replace
one.
The chart is a guide to which FRUs need to be
removed in order to remove others. The section
numbers on the chart refer to the sections in the
Maintenance Manual, Chapter 4.
Always start by removing the battery pack, next,
optional items such as the optional PC card and
optional memory module, then follow the line on
the chart to determine which FRU you must
remove next in order to repair the one you think is
causing the computer to operate improperly.
To remove the battery pack, follow the steps
below.
CAUTION: When handling battery packs, be
careful not to short circuit the terminals. Also
do not drop, hit or otherwise apply impact; do
not scratch or break the casing; and do not
twist or bend the battery pack.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Turn the computer upside down with the
front facing you and push the battery
lock up to unlock it. A red dot shows
when the lock is in the unlock position.
3. Pull out the battery release lever and
slide it to the left to pop the battery up
slightly.
4. Grasp the battery pack and lift it out.
To install the battery pack, follow the steps below.
WARNING: The battery pack is a lithium ion
battery which can explode if not replaced,
used, handled or disposed of properly.
Dispose of the battery as required by local
ordinances or regulations. Use only batteries
recommended by Toshiba as replacements.
NOTE: Check the battery terminals visually.
If they are dirty, wipe them clean with a dry
cloth.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Make sure the battery release lever is
pulled out then carefully insert the new
or recharged battery pack.
3. Place your fingers just above two pins
on the battery pack that fit into the
locking mechanisms in the battery
socket. Push the battery pack down
carefully until it locks into place.
4. Push the battery lock down to secure it.
The red dot will be covered.
4/00, Tecra
Toshiba TRR
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
You can use the SelectBay cover when you do
not need to use a SelectBay module.
1. To install the cover, first remove the
SelectBay module then hold the cover
by the two finger grips and push it into
place until you hear the latches click.
2. To remove the cover, grasp the two
finger grips and pull the cover out.
To disassemble the DVD-ROM drive, follow the
steps below.
1. Remove six M2x3 silver screws and
two M2.5x6 silver screws securing the
frame to the DVD-ROM drive.
2. Remove the connector cover.
3. Remove the metal frame, connector
board, and disconnect the flexible
cable.
î
To disassemble the FDD, follow the steps below.
1. Remove six M2x6 silver screws.
2. Turn the FDD over and release two
latches securing the upper plastic
frame and lower plastic frame. Turn it
back over and lift off the cover.
3. Lift off the upper shield cover, unseat
the flexible cable connector from the
lower plastic frame, then lift out the
FDD.
4. Pull the flexible cable out of the FDD
connector.
5. Remove four M2x3 silver screws and
remove the FDD from the bracket.
ê
è
4/00, Tecra
Toshiba TRR
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
To assemble the FDD, follow the steps below.
1. Seat the FDD in the bracket and
secure the bracket with four M2x3
silver screws. Tighten screws to a
torque of less than 2.2 kgfcm.
2. Insert the flexible cable into the
connector. Press gently to assure a
firm connection.
3. Seat the FDD in the lower plastic
frame and set the upper shield cover
in place.
4. Seat the flexible cable connector into
the lower plastic frame.
5. Set the upper plastic frame in place,
snap the two latches closed and secure
six M2x6 silver screws.
CAUTION: Be very careful not to press on
the top or bottom of the HDD. Pressure can
destroy data or damage the drive.
To remove the HDD pack, follow the steps below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack.
3. Turn the computer upside down.
4. Slide the HDD cover to the right and
push the HDD pack forward until the
back edge is aligned with a marker next
to the HDD slot.
5. Lift up on the cover to remove the HDD
pack.
To disassemble the HDD Pack, follow the steps
below.
1. Slide the cover firmly in the direction of
the arrow and remove it.
2. Remove the HDD tray and connector
cover.
í
î
Images / text continued on the next page
Toshiba TRR
Page 10
4/00, Tecra
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
Disassembling the HDD Pack, continued.
3. Remove four M2.5x6 silver screws
from HDD pack.
4. Remove four M3x4 flat-head screws
and the HDD frame.
5. Remove the flexible cable.
CAUTION: Do not try to disconnect by
pulling on the flexible cable.
CAUTION: Do not apply pressure to the top
or bottom of the HDD.
í
è
To assemble the HDD pack, follow the steps
below.
1. Connect the flexible cable connector to
the HDD.
2. Seat the HDD frame on the HDD and
secure it with four M3x4 flat-head
screws.
3. Seat the connector cover on the flexible
cable connector. Be sure to match the
positioning pins to the holes on the
flexible cable and metal cover.
CAUTION: Do not hold the HDD by its flat
surfaces. It may damage the HDD.
4. Secure four M2.5x6 silver screws.
5. Seat the cover onto the HDD.
î
4/00, Tecra
Toshiba TRR
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
To install the HDD pack, follow the steps below.
1. Align the HDD pack with the marker on
the computer and seat the HDD so that
tabs on the HDD fit into notches on the
computer.
2. Make sure the cover is pushed fully to
the right and push the HDD back to
ensure a firm connection.
3. Slide the cover to the left to lock the
HDD into the slot.
4. Install the battery pack.
To remove the memory module(s), make sure the
computer is in boot mode and follow the steps
below.
CAUTION: Do not try to remove a memory
module(s) with the computer turned on. You
can damage the computer and the memory
module(s).
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack and HDD pack.
3. Lift up the mylar cover.
4. Use a slender object (plastic card) to
press the latches on either side of the
memory module(s) to the outside and
the memory module will pop up.
5. Grasp the memory module(s) by the
sides and pull it out.
CAUTION: Do not touch the connectors on
the memory module(s) or on the computer.
Debris on the connectors may cause memory
access problems.
The modem board is located under the palmrest.
To open the palmrest, follow the steps below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, optional PC
card, and HDD pack.
3. With the computer still upside down,
remove two M2x8 silver screws, two
M2x22 silver screws and two M2x14
silver screws.
4. Turn the computer right side up and
open the display panel and PC card
cover.
î
5. Grasp the sides of the palmrest and pull
it forward until tabs on either side clear
the holes on the top cover. Three
latches are located under the palmrest
as shown below.
6. Carefully lift the palmrest.
î
Images / text continued on the next page
Toshiba TRR
Page 12
4/00, Tecra
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
Opening the palmrest, continued.
7. Remove four M2x6 screws securing
the modem board (or the dummy cover)
and lift it out.
To install a modem board, follow the steps
below.
1. Connect the modem board to the
corresponding connector in the
computer.
NOTE: Be sure a plastic insulator tab lies on
top of the green backup battery, when you
seat the modem board.
2. Make sure holes in the modem casing
are aligned with screw holes on the
computer, then secure the modem
board module with four M2x6 screws.
3. Lay the palmrest in place and press
down to seat it firmly.
í
4. Close the PC card slot cover and
display panel.
5. Turn the computer upside down.
6. Secure two M2x22 silver screws, two
M2x8 silver screws, and two M2x14
silver screws to the bottom of the
computer.
7. Install the HDD pack, optional PC card,
and battery pack.
To remove the backup and RTC batteries, follow
the steps below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, optional PC
card, HDD pack, optional memory
module and modem board.
3. Lift the backup battery mylar cover.
4. Disconnect the backup battery cable
from PJ511 on the system board,
unthread the cables and lift out the
backup battery.
5. Disconnect the RTC battery from PJ510
on the system board, unthread the
cables and lift it out.
4/00, Tecra
Toshiba TRR
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
To remove the keyboard, follow the steps below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, optional PC
card, HDD pack, optional memory
module, modem board and backup
and RTC batteries.
3. Peel off the tape placed on the folded
end of the keyboard flexible cable.
4. Disconnect the flexible cable from
PJ580 on the system board.
5. Lift up the front edge of the keyboard
and lift out the keyboard.
To remove the membrane switch, follow the
steps below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, optional PC
card, HDD pack, optional memory
module, modem board, backup and
RTC batteries, and keyboard.
3. Disconnect the membrane switch
cable from PJ570 on the system board.
4. Remove two M2.5x4 screws securing
the membrane switch unit and lift out
the unit.
To remove the top cover with display assembly,
follow the steps below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, optional PC
card, HDD pack, optional memory
module, modem board, backup and
RTC batteries, keyboard and mem-
brane switch.
3. Remove six M2.5x10 silver screws
from the bottom of the computer.
4. Remove the mask and two M2x6
screws from the position under the
battery pack.
5. Remove three M2.5x4 silver screws
from the back of the computer.
î
Images continued on the next page
Toshiba TRR
Page 14
4/00, Tecra
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
Removing the top cover with display assembly,
continued.
6. Turn the computer right side up and
open the display panel.
7. Slightly lift up the LCD cable cover and
pull it forward to remove it, then remove
the plastic lens.
8. Remove the tape off the LCD cables.
9. Remove one M2x6 screw securing the
ground cable.
10. Disconnect the LCD cable, FL inverter
cable, speaker cable and microphone
cable.
11. Remove six M2x6 screws, one M2x8
screw and three M2x4 silver screws
securing the top cover.
12. Open two port covers on the back of the
computer.
13. Pull out the top cover just below the
composite video connector (yellow) to
release a latch.
14. Carefully lift up the back side of the top
cover with display assembly. Lift slowly
to avoid damage to the two latches on
the left side of the computer.
í
î
í
4/00, Tecra
Toshiba TRR
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
To remove the speakers, follow the steps below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, optional PC
card, HDD pack, optional memory
module, modem board, backup and
RTC batteries, keyboard, membrane
switch and top cover with display
assembly.
3. Lay the display down. Partially lift the
insulator covering the speaker cables.
4. Remove four M2x4 screws securing
the speaker holders.
5. Observe how the cables are threaded,
then lift out the speakers, cables and
holders.
6. Pull the speakers out of the holders.
To remove the system board, follow the steps
below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, optional PC
card, HDD pack, optional memory
module, modem board, backup and
RTC batteries, keyboard, membrane
switch, top cover with display assembly.
3. Remove one M2x4 silver screw and
two M2.5x6 screws securing the shield
plate and remove it.
4. Remove one M2.5x4 screw near the
PC card slot.
5. Remove one M2.5x4 screw securing
the connection board and lift it out.
6. Remove one M2.5x6 screw under the
connection board.
7. Remove one M2x4 silver screw
securing the USB slot to the USB
connector.
ê
CAUTION: Do not remove the heat-sink on the
CPU. The grease can dry out and cause
damage to the CPU.
8. Lift up the system board to disconnect
three connectors.
Toshiba TRR
Page 16
4/00, Tecra
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
To remove the fan, follow the steps below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, optional PC
card, HDD pack, optional memory
module, modem board, backup and
RTC batteries, keyboard, membrane
switch, top cover with display assembly,
and system board.
3. Turn the system board upside down
and remove tape securing the fan
cable.
4. Disconnect the fan cable from PJ550
on the system board.
5. Turn the system board right side up and
remove two M2.5x4 screws.
6. Lift out the fan.
To remove the middle frame, follow the steps
below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, optional PC
card, HDD PACK, optional memory
module, modem board, backup and
RTC batteries, keyboard, membrane
switch, top cover with display assembly,
and system board.
3. Remove two M2.5x6 screws and one
M2.5x8 screw securing the SelectBay
top cover to the middle frame.
4. Two positioning pins fit into holes on
the SelectBay top cover, so lift the cover
straight up to clear the pins.
5. Remove three M2.5x10 silver screws
securing the CONN holder assembly
and lift out the CONN holder assembly.
6. Disconnect two secondary battery
cables (PJ511 and PJ512) from the I/O
board and remove the cables with the
protective metal plate.
ê
7. Remove two M2.5x8 screws securing
the middle frame to the bottom cover.
8. Pull out the SelectBay release lever
and set the SelectBay lock to the lock
position.
CAUTION: Make sure the SelectBay lock is
locked before removing the middle frame
from the bottom cover. If you remove the
middle frame while the SelectBay lock is
unlocked, the I/O board will be damaged.
NOTE: Make sure the screw in the memory
slot has been removed.
9. Remove the middle frame from the base
of the computer.
4/00, Tecra
Toshiba TRR
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
To install the middle frame, follow the steps
below.
1. Make sure the SelectBay release lever
is extended and the SelectBay lock is in
the locked position.
2. Seat the middle frame and make sure a
small tongue on the middle frame’s
SelectBay locking mechanism fits into a
corresponding notch on the external
SelectBay lock.
3. First secure one M2.5x8 screw next to
the SelectBay lock arm, then secure the
other M2.5x8 screw.
4. Place the CONN holder assembly and
secure it with three M2.5x10 silver
screws.
5. Connect two secondary battery cables
to the I/O board.
6. Seat the protective metal plate.
7. Thread the battery cables in the groove
and seat the cable holder.
8. Replace the tape.
9. Secure the SelectBay top cover with
two M2.5x6 screws and one M2.5x8
screw.
10. Install the system board, top cover with
display assembly, membrane switch,
keyboard, backup and RTC batteries,
modem board, optional memory
module, HDD pack, optional PC card,
and battery pack.
To remove the I/O board, follow the steps.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, optional PC
card, HDD pack, optional memory
module, modem board, backup and
RTC batteries, keyboard, membrane
switch, top cover with display assembly,
system board, and middle frame.
3. From the bottom of the battery pack slot,
push up on the battery jumper contact
and slide it forward.
4. Press down on the battery jumper as
shown in the figure below and slide the
jumper out to remove it.
5. Remove one M2x6 screw securing the
I/O board to the bottom cover.
î
6. Lift out the I/O board.
7. Lift out the base shield assembly (with
rubber heat conductor).
Toshiba TRR
Page 18
4/00, Tecra
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
To remove the display mask, follow the steps
below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack.
3. Remove two rubber seals at the
bottom corners of the display assembly.
4. Remove two M2.5x6 screws that were
covered by the rubber seals.
NOTE: Support the display with your hand
when you remove the screws.
5. Using the fingers of both hands,
carefully release the 18 latches along
the edges of the display mask. Begin
at the top (six latches), continue along
the sides (four latches on each side)
and the bottom (four latches).
í
To remove the FL inverter board, follow the steps
below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack and the
display mask.
3. Lay the display panel on its back.
4. Remove two M2.5x6 screws securing
the FL inverter board.
5. Lift up the FL inverter board and
disconnect the FL cable.
6. Rotate out the top end of the FL
inverter board. Disconnect the FL
inverter cable and lift out the FL
inverter board.
î
4/00, Tecra
Toshiba TRR
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
NOTE: Be careful not to apply pressure to
the ICs along the edge of the LCD module.
The ICs are easily damaged.
To remove the LCD module, follow the steps
below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, display mask
and FL inverter board as described in
Sections 4.2, 4.19 and 4.20.
3. Remove four M2.5x8 screws securing
the LCD module to the display assem-
bly.
4. Carefully rotate out the top of the LCD
module enough to access the display
cable.
5. Peel off the tape securing the cable and
disconnect the cable.
To remove the microphone, follow the steps
below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, optional PC
card, HDD pack, optional memory
module, modem board, backup and
RTC batteries, keyboard, membrane
switch, top cover with display assembly,
and speakers.
3. Lay the top cover with display assembly
down so that the bottom of the top cover
lies flat and faces up.
4. Remove one M2x4 screw securing the
hinge cover and one M2.5x6 screw
securing a plastic cable guide.
5. Remove one M2.5x4 screw holding the
microphone ground cable.
6. Release the cable guide from the top
cover at the top right corner of the left
speaker cable groove.
7. Lift the small end of the cable guide
about 2.5 cm, then use tweezers to
push down the LCD cable core to free
the cable guide.
8. Lift the cable guide straight up and pull
the microphone cable out of the cable
guide.
9. Rotate the top cover up about 90
degrees.
ê
NOTE: Grasp the top cover by the sides
when you rotate it up. Do not pull at the
center.
10. Lift out the microphone holder and
cable and remove the microphone from
the holder.
Toshiba TRR
Page 20
4/00, Tecra
Download from Www.Somanuals.com. All Manuals Search And Download.
Tecra 780CDM / 780DVD Disassembly Overview, (cont.)
CAUTION: When you remove the FL, be
careful not to let any dust or other foreign
matter contaminate the LCD panel. Any
contamination can affect the performance of
the unit.
To remove the FL, follow the steps below.
1. Turn off the power to the computer.
Disconnect the AC adapter and all
external cables connected to the
computer.
2. Remove the battery pack, optional PC
card, HDD pack, optional memory
module, modem board, backup and
RTC batteries, keyboard, membrane
switch, top cover with display assem-
bly, speakers, display mask, FL inverter
board, LCD module, and microphone.
3. Remove one strip of tape securing the
FL cable to the LCD frame and lift up
the FL cable.
4. Remove two M2x4 thin-head silver
screws and one M2x2 thin-head
silver screw to remove the metal FL
cover.
ê
5. Carefully lift up the white sheet cover-
ing the FL.
6. Lift the yellow FL cable connector until
one end is out of the groove.
CAUTION: Handle only the FL cable
instead of the FL glass tube to minimize risk
of damage or injury.
7. Lift the white FL cable out of its groove
to remove the cable and FL.
î
4/00, Tecra
Toshiba TRR
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
|