OWNER'S MANUAL
DIGITAL VIDEO
DVD VIDEO PLAYER
SD-3750
SD-K700
Jan., 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
The instructions shall state that an ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in
each pole shall be incorporated in the electrical installation of the building.
CAUTION:
These servicing instructions are for use by qualified service personnel only. To reduce the risk of
electric shock do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD player.
Model No.
Serial No.
Retain this information for future reference.
Location of the required label
PRODUCT IS CERTIFIED BY THE MANUFACTURER TO
COMPLY WITH DHHS RULE 21 CFR SUBCHAPTER J
APPLICABLE AT THE DATE OF MANUFACTURE.
MANUFACTURED
1-1,SHIBAURA 1-CHOME,MINATO-KU.
TOKYO 105-8001,JAPAN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS
OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR
FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following
procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that
can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
S3125A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
IMPORTANT SAFETY INSTRUCTIONS
13.Unplug this apparatus during lightning storms or when unused for long periods
of time.
14.Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15.When you use headphones, keep the volume at a moderate level. If you use
the headphones continuously with high volume sound, it may cause hearing
damage.
16.Do not overload wall outlets; extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
17.Never insert objects of any kind into this apparatus through openings as they
may touch dangerous voltage points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the apparatus.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
18.Keep your fingers well clear of the disc tray as it is closing. Neglecting to do
so may cause serious personal injury.
19.Do not place a heavy object on or step on the apparatus. The object may fall,
causing serious personal injury and serious damage to the apparatus.
20.Do not use a cracked, deformed, or repaired disc. These discs are easily
broken and may cause serious personal injury and apparatus malfunction.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Precautions
Notes on handling
Notes on moisture condensation
When shipping the DVD player, the original shipping
carton and packing materials come in handy. For
maximum protection, repack the unit as it was
originally packed at the factory.
Do not use volatile liquids, such as insect spray, near
the DVD player. Do not leave rubber or plastic
products in contact with the DVD player for a long
time. They will leave marks on the finish.
The top and rear panels of the DVD player may
become warm after a long period of use. This is not a
malfunction.
Moisture condensation damages the DVD player.
Please read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts of
the DVD player.
o
f
n
s
When the DVD player is not in use, be sure to
remove the disc and turn off the power.
If you do not use the DVD player for a long period,
the unit may not function properly in the future. Turn
on and use the DVD player occasionally.
Optical pick-up
lens
Moisture condensation occurs during the
following cases.
Notes on locating
When you bring the DVD player directly from a cold
place to a warm place.
Place the DVD player on a level surface. Do not use it
on a shaky or unstable surface such as a wobbling
table or inclined stand. The loaded disc may come off
the proper position and cause damage to the DVD
player.
When you place this DVD player near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, place the DVD
player away from the TV, radio, or VCR.
When you use the DVD player in a room where you
just turned on the heater, or a place where the cold
wind from the air conditioner directly hits the unit.
In summer, when you use the DVD player in a hot
and humid place just after you move the unit from an
air conditioned room.
When you use the DVD player in a humid place.
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the DVD
player.
Do not use the DVD player when moisture
condensation may occur.
If you use the DVD player in such a situation, it may
damage discs and internal parts. Remove the disc,
connect the power cord of the DVD player to the wall
outlet, turn on the DVD player, and leave it for two or
three hours. After two or three hours, the DVD player
will have warmed up and evaporated any moisture.
Keep the DVD player connected to the wall outlet and
moisture condensation will seldom occur.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
To obtain a clear picture
The DVD player is a high technology, precision device. If
the optical pick-up lens and disc drive parts are dirty or
worn down, the picture quality becomes poor. To obtain
a clear picture, we recommend regular inspection and
maintenance (cleaning or parts replacement) every
1,000 hours of use depending on the operating
Wall outlet
environment. For details, contact your nearest dealer.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on Discs
On handling discs
Structure of disc contents
Do not touch the playback side of the disc.
Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. VIDEO CDs/
audio CDs are divided into tracks.
DVD video disc
Title 2
Title 1
Chapter 1 Chapter 2
Chapter 1 Chapter 2 Chapter 3
Playback side
Do not attach paper or tape to discs.
VIDEO CD/Audio CD
Track 1
Track 2
Track 3
Track 4
Track 5
On cleaning discs
Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.
There may be discs that do not have these numbers.
Notes on copyright
It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, and rent copyrighted
material without permission.
If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
DVD video discs are copy protected, and any recordings
made from these discs will be distorted.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Notes on Discs (continued)
About this owner’s manual
Playable discs
This owner’s manual explains the basic instructions of
this DVD player. Some DVD video discs are produced in
a manner that allows specific or limited operation during
playback. As such, the DVD player may not respond to
all operating commands. This is not a defect in the DVD
player. Refer to instruction notes of discs.
This DVD player can play the following discs.
Disc
Size
Disc Mark
Contents
12 cm
“
” may appear on the TV screen during operation.
video
(moving
pictures)
+
A “ ” means that the operation is not permitted by the
DVD player or the disc.
DVD
video
discs
Audio
Notes on region numbers
8 cm
The region number of this DVD player is 1. If region
numbers, which stand for their playable area, are printed
1
ALL
on your DVD video disc and you do not find
or
,
disc playback will not be allowed by the player. (In this
case, the DVD player will display a message on-screen.)
12 cm
video
(moving
pictures)
+
VIDEO
CDs
DIGITAL VIDEO
On VIDEO CDs
Audio
8 cm
This DVD player supports VIDEO CDs equipped with
the PBC (Version 2.0) function. (PBC is the abbreviation
of Playback Control.) You can enjoy two playback
variations depending on types of discs.
12 cm
Audio
CDs
Audio
• VIDEO CD not equipped with PBC function
(Version 1.1)
8 cm
(CD single)
Sound and movie can be played on this DVD player in
the same way as an audio CD.
• VIDEO CD equipped with PBC function
(Version 2.0)
The following discs are also available.
DVD-R discs of DVD video format
CD-R/CD-RW discs of CD-DA format
In addition to operation of a VIDEO CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.
Some of these discs may be incompatible.
• You cannot play discs other than those listed above.
• You cannot play discs of DVD-RAM or
non-standardized discs, etc., even if they may be
labeled as above.
• This DVD player uses the NTSC color system, and
cannot play DVD video discs recorded in any other
color system (PAL, SECAM, etc.).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction
Advanced playback
SAFETY PRECAUTIONS ..........................2
IMPORTANT SAFETY INSTRUCTIONS ...4
Precautions ...............................................8
Accessing a Specific Location Directly .. 34
Entering the time counter of the desired
location ......................................................... 34
Playing Repeatedly.................................35
Repeating a title, chapter, or track.................. 35
Repeating a specific segment ........................ 35
Notes on Discs..........................................9
Notes on region numbers ............................... 10
Table of Contents ................................... 11
Playing in a Favorite Order ....................36
Identification of Controls .......................12
Front panel ..................................................... 12
Rear panel ...................................................... 12
DVD display.................................................... 13
Remote control ............................................... 14
Loading batteries ............................................ 15
Operating with the remote control .................. 15
Setting titles, chapters, or tracks in a favorite
order ............................................................. 36
Playing in Random Order ......................37
Playing titles, chapters, or tracks in random
order ............................................................. 37
Zooming a Picture ..................................38
Zooming a picture........................................... 38
Selecting the Sound Enhancement
(E.A.M.) ....................................................39
Selecting the sound enhancement ................. 39
Connections
Connecting to a TV .................................18
Connecting to a TV......................................... 18
Connecting to an audio system and TV
equipped with component video inputs ........ 19
Selecting the Camera Angle ..................40
Changing the camera angle ........................... 40
Selecting Subtitles .................................41
Selecting a subtitle language ......................... 41
Connecting to Optional Equipment ......20
Connecting to an amplifier equipped with a
Dolby Digital decoder ................................... 21
Selecting a Language.............................42
Connecting to an amplifier equipped with
Dolby Pro Logic Surround ............................ 21
Selecting a playback audio setting ................. 42
Connecting to an amplifier equipped with a
DTS decoder ................................................ 22
Connecting to an amplifier equipped with an
MPEG2 audio decoder ................................. 22
Connecting to an amplifier equipped with a
digital audio input ......................................... 23
Quick control
Using the Graphic Remote Control
- V-REMOTE - ..........................................46
Selecting the Playback Function
- QUICK -..................................................47
Accessing Features
- NAVI - .....................................................48
Basic playback
Playing a Disc .........................................26
Basic playback ............................................... 26
Function setup
Customizing the Function Settings ......56
Setting procedure ........................................... 56
Setting details ................................................. 58
Variable Speed Playback .......................28
Playing in fast reverse or
fast forward directions .................................. 28
Playing frame by frame .................................. 28
Playing in slow-motion.................................... 29
Resuming playback from the same location... 29
Table of Languages ................................65
Others
Locating a Desired Section ...................30
Locating a title using the top menu................. 30
Locating a desired section by entering the
corresponding number ................................. 31
Before Calling Service Personnel .........68
Specifications .........................................69
LIMITED WARRANTY DVD PLAYER......70
Locating a specific chapter or track ................ 31
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Identification of Controls
See the page in
for details.
Front panel
OPEN/CLOSE button
PAUSE button 27
STOP button
26
POWER indicator
26
27
Disc tray
26
PLAY button
26
PAUSE
STOP
PLAY
OPEN/CLOSE
POWER
NAVI
SKIP
TOP MENU MENU RETURN
ENTER
13
SKIP buttons 31
DVD display
26
RETURN button 56
MENU button
POWER button
56
/ ENTER button
/
/
/
48
NAVI button
TOP MENU button 30
Rear panel
ColorStream® (Component video)
VIDEO OUT jacks (Y/PB/PR)
2CH AUDIO OUT jacks 18 19
19
BITSTREAM/PCM COAXIAL (DIGITAL)
18
VIDEO OUT jack
AUDIO OUT jack
21 22 23
AC inlet
VIDEO OUT
AUDIO OUT
2CH
BITSTREAM
/PCM
AC IN
Y
VIDEO
L
PB
SELECT
R
PR
S
I
P
COAXIAL OPTICAL
DIGITAL
S VIDEO OUT jack
BITSTREAM/PCM OPTICAL (DIGITAL)
AUDIO OUT jack
18
21 22 23
SELECT (I/P) switch
19
When connecting the optical digital cable, remove
the cap and fit the connector into the jack firmly.
When not using the jack, keep the cap inserted
to protect it from dust intrusion.
Power cord
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeated pressing of the FL DIMMER button on
the remote control changes the brightness of the
display.
DVD display
Dimmed
Off
Normal
FL DIMMER
Remaining time/elapsed time indicators
Memory playback indicator
Chapter/track number indicator
Title number indicator
Random playback indicator
Play mode indicator
TITLE
CHP
TRK
REMAIN
MEMORY RANDOM A-B
HDCD
DVD
VCD
VIDEO CD/CD indicator
DVD indicator
Multifunctional indicator (indicates operating
status or messages, etc.)
Angle icon indicator
Repeat playback indicator
The indicators vary depending on the kinds of discs you play.
VIDEO CD
Audio CD
DVD video disc
• During playback:
• During playback:
• During playback:
Example
Example
Example
TITLE GROUP CHP
TRK
TOTAL REMAIN
MEMORY RANDOM A-B
TITLE GROUP CHP
TRK
TOTAL REMAIN
MEMORY RANDOM A-B
TITLE GROUP CHP
TRK
TOTAL REMAIN
MEMORY RANDOM A-B
HDCD
HDCD
HDCD
DVD-
AUDIO
DVD-
AUDIO
DVD
-AUDIO
SVCDVD
SVCDVD
SVCDVD
Playing track 6 Elapsed time of
the current track
Playing track 6 Elapsed time of
the current track
Playing chapter 3 Elapsed time of
of title 2 the current title
• Some discs may not display chapter
numbers.
Some discs may not display track
numbers or elapsed time.
• A time indication not accompanied
with a chapter number shows
elapsed time of a segment within the
current title.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Identification of Controls (continued)
The instructions in this manual describe the functions on the remote control. See the page in
for details.
Remote control
Power button 26
SETUP button 56
E.A.M button 39
NAVI button
OPEN/CLOSE button 26
OPEN/CLOSE FL DIMMER SETUP
ZOOM
FL DIMMER button 13
E.A.M
NAVI
ZOOM buttons 38
QUICK button 47
TOP MENU button 30
QUICK V-REMOTE
48
TOP MENU
MENU
MENU button*
ENTER
V-REMOTE button
46
56
ENTER button
CLEAR
RETURN
STOP
RETURN button 56
Direction buttons
( / / / )
56
PAUSE/STEP
PLAY
STOP button 27
PLAY button 26
FWD button 28
REV button 28
T button 31
SKIP
REV
FWD
CLEAR button 31
SEARCH
PAUSE/STEP button 27
3
6
9
1
4
7
2
5
8
T
+10
SKIP buttons 31
0
SLOW
SLOW buttons 29
Number buttons
31
COLORSTREAM
SELECTOR
ANGLE SUBTITLE AUDIO
COLORSTREAM SELECTOR
ANGLE button 40
RANDOM MEMORY REPEAT A-B RPT
button
19
RANDOM button 37
A-B RPT button 35
AUDIO button 42
REPEAT button 35
SUBTITLE button 41
MEMORY button 36
* MENU button
Use the MENU button to display the
menu included on many DVD video
discs. To operate a menu, follow the
instructions in “Locating a title using
the top menu.” 30
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading batteries
Operating with the remote control
Open the cover.
Point the remote control at the remote
sensor and press the buttons.
1
30°
30°
Insert batteries (AA size).
Within about 7 m (23 feet)
2
3
Distance: About 7 m (23 feet) from the front of the
remote sensor
Angle:
About 30° in each direction of the front of
the remote sensor
Make sure to match the + and – on the batteries
to the marks inside the battery compartment.
* Do not expose the remote sensor of the DVD player
to a strong light source such as direct sunlight or
other illumination. If you do so, you may not be able
to operate the DVD player via the remote control.
Close the cover.
Notes on the remote control
• Direct the remote control at the remote sensor of the DVD
player.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot or
humid place.
• Do not spill water or put anything wet on the remote
control.
• Do not open the remote control.
Notes on batteries
Improper use of batteries may cause battery leakage and
corrosion. To operate the remote control correctly, follow the
instructions below.
• Do not insert batteries into the remote control in the wrong
direction.
• Do not charge, heat, open, or short-circuit the batteries.
Do not throw batteries into a fire.
• Do not leave dead or exhausted batteries in the remote
control.
• Do not use different types of batteries together, or mix old
and new batteries.
• If you do not use the remote control for a long period of
time, remove the batteries to avoid possible damage from
battery corrosion.
• If the remote control does not function correctly or if the
operating range becomes reduced, replace all batteries
with new ones.
• If battery leakage occurs, wipe the battery liquid from the
battery compartment, then insert new batteries.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Read this chapter first to make all necessary
preparations.
Connecting to a TV
Connecting to an audio system
and TV equipped with
component video inputs
Connecting to an amplifier
equipped with a Dolby Digital
decoder
Connecting to an amplifier
equipped with Dolby Pro Logic
Surround
Connecting to an amplifier
equipped with a DTS decoder
Connecting to an amplifier
equipped with an MPEG2 audio
decoder
Connecting to an amplifier
equipped with a digital audio
input
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to a TV
Connect the DVD player to your TV.
For details of output sound, see 43
.
Connecting to a TV
Signal flow
VIDEO OUT
AUDIO OUT
2CH
BITSTREAM
/PCM
AC IN
Y
VIDEO
L
PB
SELECT
R
PR
S
I
P
COAXIAL OPTICAL
DIGITAL
To S VIDEO OUT
(yellow) (white)
To VIDEO OUT
(red)
To 2CH AUDIO OUT
SELECT
I
P
To wall outlet
Set to “I.”
S video cable
(not supplied)
Audio/video cable
(supplied)
TV or monitor with
audio/video inputs
(red)
To audio inputs
To video input
(white)
(yellow)
If the TV has an S video input, connect the
DVD player with an S video cable. When
using an S video cable, do not connect the
yellow video cable.
To S video input
• Make the following setting.
On-screen display
Select:
Page
“Bitstream”
or
“PCM”
56
59
“Audio Out Select”
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
• If your television set has one audio input, connect the left and right audio outputs of the DVD player to a Y cable adapter (not
supplied) and then connect to your TV.
• Connect the DVD player directly to your TV. If you connect the DVD player to a VCR, TV/VCR combination or video selector,
the playback picture may be distorted as DVD video discs are copy protected.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
INTERLACED outputs/inputs (ColorStream®)
Some TVs or monitors are equipped with component video
inputs. Connecting to these inputs allows you to enjoy
higher quality picture playback.
Actual labels for component video inputs may vary
depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y,
CB, CR)
PROGRESSIVE outputs/inputs (ColorStream®Pro)
Some TVs or monitors are equipped with component video
inputs that are capable of reproducing a progressively
scanned video signal. Connecting to these inputs allows
you to view the highest quality pictures with less flicker.
In some TVs or monitors, the color levels of the playback
picture may be reduced slightly or the tint may change. In
such a case, adjust the TV or monitor for optimum
performance.
Connecting to an audio system and TV equipped with component video inputs
Signal flow
VIDEO OUT
Y
AUDIO OUT
2CH
BITSTREAM
/PCM
AC IN
VIDEO
L
P
B
R
SELECT
R
P
S
I
P
COAXIAL OPTICAL
DIGITAL
To Y
VIDEO
OUT
To PR
VIDEO VIDEO
OUT OUT
To PB
(red)
(white)
Audio system
(red)
(white)
To wall outlet
To audio inputs of the amplifier
TV or monitor with
component video
(INTERLACED) inputs
or
TV or monitor with
component video
(PROGRESSIVE) inputs
SELECT
Set to “I.”
To PB video input
I
P
To PR video input
To Y video input
SELECT
Set to “P.”
I
P
Switching the output signal (interlaced/
progressive) using the remote control
(only when the SELECT (I/P) switch is set to “P”)
You can temporarily switch the output signal for better
picture quality.
Press COLORSTREAM SELECTOR on the remote
control.
• Make the following setting.
On-screen display
Select:
Page
“Bitstream”
or
“PCM”
56
59
“Audio Out Select”
Notes
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
• If you place the DVD player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD
player away from the tuner and radio.
• The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD player’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
• The S VIDEO OUT jack and the VIDEO OUT jack cannot output video signals, if you select progressive signal when the
SELECT (I/P) switch is set to “P.”
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD player to
optional audio equipment.
• For connection to your TV, see “Connecting to a TV”
Warning
18 19
.
• When you are connecting (via the BITSTREAM/PCM
(DIGITAL) AUDIO OUT jack) an AV decoder that does
not have Dolby Digital, Digital Theater Systems (DTS)
or MPEG2 decoding function, be sure to set “Audio Out
43
• For details of output sound, see
.
• This section uses the following reference marks.
56 59
Select” to “PCM” from the on-screen displays
.
: Front speaker
: Rear speaker
: Sub woofer
Otherwise, high volume sound may damage your
hearing as well as the speakers.
• When playing DTS-encoded discs (audio CDs),
excessive noise may be output from the analog audio
output jacks. To avoid possible damage to the audio
system, you should take proper precautions when the
analog audio output jacks of the DVD player are
connected to an amplification system. To enjoy DTS
Digital Surround™ playback, an external 5.1 channel
DTS Digital Surround™ decoder system must be
: Center speaker
: Signal flow
connected to the BITSTREAM/PCM (DIGITAL) AUDIO
OUT jack of the DVD player.
Notes
• DO NOT connect the BITSTREAM/PCM (DIGITAL)
AUDIO OUT jack of the DVD player to the AC-3 RF input
of a Dolby Digital Receiver. This input on your A/V
Receiver is reserved for Laserdisc use only and is
incompatible with the BITSTREAM/PCM (DIGITAL)
AUDIO OUT jack of the DVD player.
• Connect the BITSTREAM/PCM (DIGITAL) AUDIO OUT
jack of the DVD player to the “DIGITAL (OPTICAL)” or
“DIGITAL (COAXIAL)” input of a Receiver or Processor.
• Refer to the owner’s manual of the connected equipment
as well.
• When you connect the DVD player to other equipment, be
sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.
• The output sound of the DVD player has a wide dynamic
range. Be sure to adjust the receiver’s volume to a
moderate listening level. Otherwise, the speakers may be
damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the
DVD player’s power cord. If you leave the amplifier power
on, the speakers may be damaged.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to an amplifier equipped with a Dolby Digital decoder
Dolby Digital
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and
Dolby Digital is the surround sound technology used in theaters showing the
latest movies, and is now available to reproduce this realistic effect in the home.
You can enjoy motion picture and live concert DVD video discs with this dynamic
realistic sound by connecting the DVD player to a 6 channel amplifier equipped
with a Dolby Digital decoder or Dolby Digital processor. If you have a Dolby Pro
Logic Surround decoder, you will obtain the full benefit of Pro Logic from the
same DVD movies that provide full 5.1-channel Dolby Digital soundtracks, as well
as from titles with the Dolby Surround mark.
the double-D symbol are trademarks of
Dolby Laboratories. Confidential
unpublished works. ©1992-1997 Dolby
Laboratories. All rights reserved.
• Use DVD video discs encoded via
the Dolby Digital recording
system.
• Make the following setting.
On-screen display
Select:
Page
VIDEO OUT
Y
AUDIO OUT
BITSTREAM
/PCM
2CH
Amplifier equipped with a
Dolby Digital decoder
VIDEO
56
59
P
B
R
L
SELECT
“Audio Out Select” “Bitstream”
R
P
S
I
P
COIAL OPTAL
DIGITAL
To OPTICAL
type digital
audio input
To COAXIAL
type digital
audio input
42
Recording system
D
Connect either.
75 Ω coaxial cable
Optical digital cable
Connecting to an amplifier equipped with Dolby Pro Logic Surround
• Make the following setting.
Dolby Pro Logic Surround
You can enjoy the dynamic realistic sound of Dolby Pro Logic Surround by
connecting an amplifier and speaker system (right and left front speakers, a
center speaker, and one or two rear speakers).
On-screen display
Select:
Page
“Bitstream”
or
“PCM”
56
59
“Audio Out Select”
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an
amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s
owner’s manual and set the amplifier so you can enjoy Dolby Pro Logic
Surround sound.
Be sure to set “Audio Out Select”
to “Bitstream” or “PCM” when
you enjoy sounds of Dolby Pro
Logic Surround using this
connection.
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
* Connect one or two rear speakers.
The output sound from the rear speakers
will be monaural even if you connect two
rear speakers.
VIDEO OUT
Y
AUDIO OUT
BITSTREAM
2CH
/PCM
Amplifier equipped with
Dolby Pro Logic Surround
VIDEO
P
B
R
L
*
SELECT
R
P
S
I
P
COAXIAL OPTICAL
DIGITAL
To audio input
To 2CH AUDIO OUT
Audio cable
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to Optional Equipment (Continued)
Connecting to an amplifier equipped with a DTS decoder
Digital Theater Systems (DTS)
“DTS” and “DTS Digital Surround” are
DTS is a high quality surround technology used in theaters and now available for
home use, on DVD video discs or audio CDs.
trademarks of Digital Theater Systems,
Inc.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1
channel DTS encoded sound tracks on DVD video discs or audio CDs.
• Use DVD video discs or audio
CDs encoded via the DTS
recording system.
• Make the following setting.
VIDEO OUT
Y
AUDIO OUT
BITSTREAM
2CH
/PCM
Amplifier equipped with
a DTS decoder
VIDEO
P
B
R
L
On-screen display
“Audio Out Select” “Bitstream”
Recording system DTS
Select:
Page
SELECT
R
P
S
I
P
COAIAL OPTIAL
DIGITAL
56
59
To OPTICAL
type digital
audio input
To COAXIAL
type digital
audio input
Connect either.
42
75 Ω coaxial cable
Optical digital cable
Connecting to an amplifier equipped with an MPEG2 audio decoder
• Use DVD video discs encoded via
the MPEG2 recording system.
• Make the following setting.
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs with dynamic
realistic sound by connecting an amplifier equipped with an MPEG2 audio
decoder or MPEG2 audio processor.
On-screen display
“Audio Out Select” “Bitstream”
Recording system MPEG
Select:
Page
56
59
VIDEO OUT
Y
AUDIO OUT
BITSTREAM
2CH
/PCM
Amplifier equipped with an
MPEG2 audio decoder
VIDEO
P
B
R
L
42
SELECT
R
P
S
I
P
COAIAL OPTAL
DIGITAL
To OPTICAL
type digital
audio input
To COAXIAL
type digital
audio input
Connect either.
75 Ω coaxial cable
Optical digital cable
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
• Make the following setting.
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an
amplifier equipped with a digital audio input and speaker system (right and left
front speakers).
On-screen display
Select:
Page
56
59
“Audio Out Select”
“PCM”
VIDEO OUT
Y
AUDIO OUT
BITSTREAM
2CH
/PCM
Amplifier equipped with
a digital audio input
VIDEO
P
B
R
L
SELECT
R
P
S
I
P
COAAL OPTAL
DIGITAL
To OPTICAL
type digital
audio input
To COAXIAL
type digital
audio input
Connect either.
75 Ω coaxial cable
Optical digital cable
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
Begin your operation.
Playing a Disc
Variable Speed Playback
Locating a Desired Section
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
Playing a Disc
This section shows you the basics on how to play a disc.
3
2, 4 PAUSE PLAY
POWER indicator
STOP
1
MENU
TOP MENU
DVD display
/
/ ENTER
DVD-V VCD
CD
Basic playback
Preparations
• When you want to view a disc, turn on the TV and select the video input connected to the DVD player.
• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected
to the DVD player.
Press the power button (POWER).
Press OPEN/CLOSE to close the disc
tray.
4
1
The DVD player turns on and the
POWER
POWER indicator on the player
illuminates.
OPEN/CLOSE
Playback starts.
If you insert a DVD video disc that contains a top
menu, a menu may appear. See “Locating a title
using the top menu.” 30
You may need to press the TOP MENU or MENU
button to display disc menu (depending on the
actual DVD video disc.)
When the DVD player is turned on for
the first time, an on-screen display will appear
to provide initial settings. Press the
buttons to select an item, and press the
ENTER button. See the pages in , and
buttons, then
/
make a selection using the
press the ENTER button.
60
/
On-Screen Language
Note
58
TV Shape
If the disc tray contains a disc you have already played,
playback will begin from the location where you last stopped
After making all the settings, select “ ” and
press the ENTER button.
29
playback.
To start playback in the stop mode
Press PLAY.
Press OPEN/CLOSE.
2
3
The disc tray opens.
OPEN/CLOSE
PLAY
Place a disc on the disc tray.
With the playback
side down.
• There are two different disc sizes. Place the disc in
the correct guide on the disc tray. If the disc is out
of the guide, it may damage the disc and cause the
DVD player to malfunction.
• Do not place a disc which is unplayable in this
DVD player.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
To obtain a higher quality picture
1
Occasionally, some picture noise not usually visible during a normal broadcast may
appear on the TV screen while playing a DVD video disc because the high
resolution pictures on these discs include a lot of information. While the amount of
noise depends on the TV you use with this DVD player, you should generally
reduce the sharpness adjustment on your TV when viewing DVD video discs.
2, 4
TOP MENU
MENU
/ / ENTER
STOP
DVD-V VCD
CD
About
The
DVD-V VCD
CD
icons on the heading bar show the playable discs for the
PLAY
function described under that heading.
PAUSE/STEP
VCD
DVD-V
CD
: VIDEO CDs.
: DVD video discs.
: Audio CDs.
To pause playback (still mode)
About the screen saver
Press PAUSE/STEP during playback.
To resume normal playback, press
the PLAY button.
If you pause a picture of a DVD video disc and leave it
still for a long while, the screen saver of the DVD player
automatically appears (when “Screen Saver” is set to
“On” 62 ). To turn off the screen saver, press the PLAY
button.
PAUSE/STEP
• Sound is muted during still mode.
Automatic Power Off function
To stop playback
Press STOP.
If the DVD player is stopped, or the screen saver is
engaged for approximately 20 minutes, the DVD player
will automatically turn itself off.
STOP
To remove the disc
Press OPEN/CLOSE.
Remove the disc after the disc tray
opens completely.
OPEN/CLOSE
Be sure to press the OPEN/CLOSE button to close
the disc tray after you remove the disc.
Notes
• Do not move the DVD player during playback. Doing so may damage the disc.
• Use the OPEN/CLOSE button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may
cause the DVD player to malfunction.
• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD player to
malfunction.
• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the
STOP button on your remote control once the movie is completed.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
Variable Speed Playback
You can play discs at various speeds, and resume playback from the location
where you stopped playback.
PLAY
FWD
REV
PAUSE/STEP
DVD-V VCD
CD
Playing in fast reverse or fast forward directions
To resume normal playback
Press PLAY.
Press REV or FWD during playback.
REV : Fast reverse playback
FWD: Fast forward playback
REV
FWD
PLAY
Each time you press the REV or
FWD button, the playback speed
changes.
Notes
• The DVD player mutes sound and omits subtitles during
reverse and forward scan of DVD video discs.
• The playback speed may differ depending on the disc.
DVD-V VCD
CD
Playing frame by frame
To resume normal playback
Press PLAY.
Press PAUSE/STEP during still playback.
PAUSE/STEP
Each time you press the PAUSE/
STEP button, the picture advances
one frame.
PLAY
Note
The sound is muted during frame by frame playback.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
STOP
PLAY
SLOW
DVD-V VCD
CD
Playing in slow-motion
To resume normal playback
Press PLAY.
Press SLOW during playback.
SLOW
Each time you press the SLOW
button, the slow-motion speed
changes.
PLAY
If you press the SLOW
button
SLOW
Notes
during playback, you can view the
picture in reverse slow-motion. (Only
when using a DVD video disc.)
• The sound is muted during slow-motion playback.
• The playback speed may differ depending on the disc.
Each time you press the SLOW
button, the slow-motion speed
changes.
DVD-V VCD
CD
Resuming playback from the same location
2 Press PLAY.
Press STOP at the location where you
want to interrupt playback.
PLAY
DVD-V
Playback starts from the
beginning of the current title.
Playback starts from the
beginning of the disc.
1
2
STOP
The DVD player memorizes the
location where playback is stopped.
VCD
CD
• If you want to return to the beginning of a DVD video
disc, open and close the disc tray once with the
OPEN/CLOSE button before pressing the PLAY
button.
Press PLAY.
PLAY
The DVD player resumes playback
from the location where you stopped
playback.
Notes
• Resuming cannot function when:
62
–you change the parental lock setting
or select a disc
menu language 60
–you play a PBC-featured VIDEO CD while “PBC” 64 is
set to “On.”
.
To start playback from the beginning regardless
of the location where you stopped playback
1 Press STOP twice.
–you open the disc tray.
• There may be a difference in the location where playback
resumes depending on the disc.
STOP
The DVD player effaces the memory
of the location.
• Settings you changed using the on-screen displays while the
DVD player keeps a location in the memory may function
only after the memory is cleared.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
Locating a Desired Section
TOP MENU
/ / / / ENTER
Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs are
divided into tracks.You can quickly locate any specific title, chapter, or track.
DVD video disc
Title 1
Title 2
VIDEO CD/Audio CD
Track 2 Track 4
Chapter 1 Chapter 2
Chapter 1 Chapter 2 Chapter 3
Track 1
Track 3
Track 5
DVD-V VCD
CD
Locating a title using the top menu
Press TOP MENU.
Press ENTER.
TOP MENU
1
2
3
ENTER
The top menu appears on the TV
screen.
Playback starts from chapter 1 of the
selected title.
e.g.
TITLE 1
TITLE 2
Notes
• The instructions above describe basic procedures which
may vary depending on the contents of the DVD video disc.
If different instructions appear on the TV screen, follow those
instructions.
• If you display the top menu during playback and press the
TOP MENU button again without selecting any title, the DVD
player may resume playback from the point where you first
pressed the TOP MENU button (depending on the actual
DVD video disc.)
• This method of locating a title is available only on a disc that
contains a top menu.
• Instruction notes of discs may refer to the button that
displays the top menu as TITLE button.
TITLE 3
TITLE 4
Press
want.
/
/
/
to select the title you
If the titles in the top menu are
assigned a number, you can directly
locate a specific title by pressing its
designated number with the number
buttons.
ENTER
30
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEAR
/ / / / ENTER
PLAY
T
Number buttons
SKIP
DVD-V VCD
CD
Locating a desired section by entering the corresponding number
Press T.
Repeat steps 2 and 3 if necessary.
1If you are using a VIDEO CD/audio CD, skip steps 1
and 2. Then at step 3, enter the number for the track
you want using the number buttons.
4
5
Press PLAY or ENTER.
ENTER
Playback starts from the
PLAY
SEARCH
e.g.
selected section.
T
–
:––:––
1
1
Press
to locate.
/
to select a section you want
Notes
2
3
• Pressing the CLEAR button resets the numbers. To clear the
display, press the T button several times.
• This method of locating a title is available only on a disc that
contains title numbers.
e.g. When you want to locate a
chapter.
ENTER
–
:––:––
1
1
Press
section.
/
to enter a number of the
Also the number buttons are
available.
ENTER
e.g. To enter 25
or
+10 +10
5
2
5
DVD-V VCD
CD
Locating a specific chapter or track
Notes
Press SKIP
or
repeatedly to display
• Some titles may not display chapter numbers.
• When you set “Title Stop” to “Off” 64 , you can access
chapters in another title. If you go back to the preceding title
the chapter or track number you want.
Playback starts from the selected chapter or track.
by pressing the SKIP
button, the DVD player locates the
first chapter of the title. When “Title Stop” is set to “On,” you
can access chapters only within the current title.
To locate succeeding chapters or
tracks.
SKIP
• If you press and hold the SKIP
or
button on the front
panel during playback, the DVD player performs fast reverse
or fast forward playback. You can vary the speed by
pressing the button further.
To locate chapters or tracks during fast reverse or fast
forward playback, first press the PLAY button to resume
Playback starts from the beginning of
the current chapter or track.
When you press twice, playback starts
from the beginning of the preceding
chapter or track.
SKIP
normal playback, then use the SKIP
or
button.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Customizing the performance of your DVD player.
Accessing a Specific Location
Directly
Playing Repeatedly
Playing in a Favorite Order
Playing in Random Order
Zooming a Picture
Selecting the Sound
Enhancement (E.A.M.)
Selecting the Camera Angle
Selecting Subtitles
Selecting a Language
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Accessing a Specific Location Directly
You can access a specific location by entering its corresponding time (hours,
minutes, seconds).
3
3
1
2
DVD-V VCD
CD
Entering the time counter of the desired location
Notes
Press T several times.
• Some discs may not respond to this process.
• Some scenes may not be located precisely as you
specified.
• This method for accessing specific locations is available
only within the current title of the DVD video disc or within
the current track of the VIDEO CD/audio CD.
1
SEARCH
You may have to press further
depending on the disc. Press the
button repeatedly until the clock icon
is highlighted.
T
e.g.
–
:––:––
1
1
Press the number buttons to enter the
time.
e.g.
2
3
1
2
5
3
0
:
:
1
1
1 25 30
Press PLAY or ENTER.
PLAY
Playback starts from the desired
location.
ENTER
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Repeatedly
You can play a specific title, chapter, track, or segment repeatedly.
/
PLAY
CLEAR
REPEAT
A-B RPT
DVD-V VCD
CD
Repeating a title, chapter, or track
If you select the mode during
playback, the DVD player
automatically starts repeat playback
after finishing the current title,
chapter, or track.
Press REPEAT.
1
REPEAT
The mode menu appears.
Press REPEAT or
select the repeat playback mode.
/
repeatedly to
Press PLAY.
2
3
The DVD player starts repeat
playback.
Press the PLAY button within about
5 seconds after you press the
REPEAT button.
PLAY
REPEAT
The mode changes as follows (when
using the REPEAT button):
Chapter Repeat
DVD-V
ENTER
Title Repeat
DVD-V
Track Repeat
VCD
CD
To resume normal playback
Press CLEAR.
DVD-V
VCD
CD
All Repeat
CLEAR
Repeat off
Chapter Repeat: Repeats the current chapter.
Note
Track Repeat:
Title Repeat
All Repeat:
Repeats the current track.
Repeats the current title.
Repeats the entire disc.
Resumes normal playback.
Some discs may not permit repeat operation.
Repeat Off:
DVD-V VCD
CD
Repeating a specific segment
To resume normal playback
Press CLEAR.
Press A-B RPT at the beginning of the
segment (point A) you want to play
repeatedly.
1
2
CLEAR
A-B RPT
A–
Notes
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a segment that
includes multiple camera angles 40
• You can specify a segment only within the current title.
• There may be a slight difference between point A and the
location where playback actually resumes depending on the
disc.
Press A-B RPT again at the end of the
segment (point B).
.
The DVD player automatically
returns to point A and starts repeat
playback of the selected segment
(A-B).
A-B RPT
A–B Repeat
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Playing in a Favorite Order
You can combine your favorite titles, chapters, or tracks and play them in the
order you determine.You can program up to 30 selections into the memory.
(Memory playback)
/ / / / ENTER
3
2
CLEAR
1
DVD-V VCD
CD
Setting titles, chapters, or tracks in a favorite order
To change the programmed selections
1 While the display appears on the TV screen, press
Insert a disc and press MEMORY during
stop.
1
2
the
/
/
/
buttons to highlight the item you
want to change.
2 Change the selection following the instructions in
The following display appears.
MEMORY
step 2.
Memory List
:
:
:
:
:
:
:
--
--
--
--
--
--
--
:
:
:
:
:
:
:
---
---
---
---
---
---
---
1
2
3
4
5
6
7
T
T
T
T
T
T
T
CT
CT
CT
CT
CT
CT
CT
To cancel the programmed selections
1 While the display appears on the TV screen, press
T: Title number
CT: Chapter number
or track number
the
/
buttons to highlight the item you want to
cancel.
2 Press CLEAR.
To resume normal playback from memory
playback
Press CLEAR.
Select the items in the order you want
by pressing the number buttons, then
ENTER for each item.
The memory playback indicator
disappears.
CLEAR
Each time you press the
/
buttons, the spaces
of “T” and “CT” are highlighted in turn. Highlight
where you want to enter, then press the
corresponding number buttons.
To select tracks from a VIDEO CD/audio CD in
order, press the number buttons for the track,
then press the ENTER button for each selection
you want.
Notes
• Some discs may not permit memory playback operation.
• If you press the REPEAT button during memory playback,
the DVD player repeats the current memory playback.
• If you press the MEMORY or RETURN button while the
display appears on the TV screen, the display disappears.
• The programmed selections will be cleared when:
– you turn off the DVD player.
Note
The space of “T (Title)” may be showing a number.
Neglect this number when using a VIDEO CD/audio
CD.
– you open the disc tray.
To select another chapter in the same title, you do
not need to select the title number.
Press PLAY while the display appears
on the TV screen.
3
PLAY
The DVD player starts memory
playback.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing in Random Order
You can play titles, chapters, or tracks in random order.
(Random playback)
2
3
CLEAR
1, 2
DVD-V VCD
CD
Playing titles, chapters, or tracks in random order
To resume normal playback
Press CLEAR.
Press RANDOM.
1
RANDOM
The mode menu appears.
CLEAR
Press RANDOM or
/
repeatedly to
Notes
select the random playback mode.
• Some discs may not permit random playback operation.
• You cannot use the random playback function in conjunction
with the memory playback function.
2
RANDOM
ENTER
The mode changes as follows (when
using the RANDOM button):
DVD-V
Chapter Random Plays the chapters
within the current title in
random order.
DVD-V
Title Random
Track Random
Track Random
Plays titles in random
order.
Plays tracks in random
order.
Plays tracks in random
order.
VCD
CD
Random Off
Resumes normal
playback.
If you select the mode during
playback, the DVD player
automatically starts random
playback after finishing the current
title, chapter, or track.
Press PLAY.
3
The DVD player starts random
playback.
Press the PLAY button within about
5 seconds after you press the
RANDOM button.
PLAY
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Zooming a Picture
ZOOM–/ZOOM/ZOOM+
/ / / / ENTER
You can magnify areas within a picture.
DVD-V VCD
CD
Zooming a picture
During normal, slow or still playback,
press ZOOM, ZOOM+ or ZOOM–.
Zoom point
To shift:
1
The DVD player enters the zoom
playback mode, and a monitor scope
and an icon appear.
ZOOM
Press the
/
/
/
buttons.
ENTER
e.g.
To hide the monitor scope and the icon during
zoom playback
Press
/
/
/
to select “EXIT,” and press ENTER.
ENTER
Select the zoom point and
magnification level.
2
Magnification level
To resume normal playback
Press ZOOM repeatedly until the monitor scope and the
icon disappear.
• To use the fixed levels:
You can select from the followings.
– Magnification
– Image reduction
– Normal playback
Alternatively press
/
/
/
to select “ZOOM” on the
icon, and press ENTER repeatedly until the monitor
scope and the icon disappear.
ZOOM
Press the ZOOM button
repeatedly.
Notes
• Some discs may not respond to zoom feature.
• During some scenes, the buttons may not work as
described.
• Zooming does not work on subtitles or menus included on
DVD video discs.
Alternatively press the
ENTER
/
/
/
buttons to select
“ZOOM” on the icon, and
press the ENTER button
repeatedly.
• While the icon is displayed, the
/
/
/
/ENTER buttons
cannot work on menus included on DVD video discs. If you
want to view the menus, cancel the zoom playback.
• The magnification level varies depending on the picture size
58
you select.
• To zoom in (or to zoom out):
Press repeatedly or press and
hold the ZOOM+ (or ZOOM–)
button.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Sound Enhancement (E.A.M.*)
1, 2
You can easily switch a preferred audio enhancement.
ENTER
*E.A.M.: Enhanced Audio Mode
2
DVD-V VCD
CD
Selecting the sound enhancement
To exit the audio enhancement selection
Press ENTER.
Press E.A.M.
1
2
The sound enhancement menu
appears.
E.A.M
ENTER
Alternatively leave the DVD player unattended for about
5 seconds after having made a selection.
Notes
• Actual effects to sounds may vary depending on the speaker
systems. Make selection according to your preference.
• Actual effects to sounds may vary depending on the disc.
• When the DVD player is connected to an amplifier equipped
with Dolby Pro Logic Surround, select “Normal”.
Otherwise, Dolby Pro Logic Surround may function
differently than usual.
Press E.A.M or
/
repeatedly to
select the sound enhancement.
E.A.M
• Selecting “Dialogue” disables “Dynamic Range Control”
function 59
Normal:
.
Normal sound.
Spatializer® 3-Dimensional Sound Processing provided by Desper
Products. Inc.
Certain audio features of this product manufactured under a license
from Desper Products, Inc., Spatializer® and the circle-in-square
device are trademarks owned by Desper Products, Inc.
ENTER
3D (N-2-2):
To obtain expansive virtual surround
sound effects from just two
speakers.
Dialogue:
To control critical center channel
information to make dialogue more
intelligible (only when playing a DVD
video disc recorded on the Dolby
Digital recording system).
• To use this enhancement on
sounds output from the
BITSTREAM/PCM (DIGITAL)
AUDIO OUT jack, be sure to set
59
“Audio Out Select” to “PCM”.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Selecting the Camera Angle
If the scene was recorded from multiple angles, you can easily change
the camera angle of the scene you are watching.
2
CLEAR
1, 2
DVD-V VCD
CD
Changing the camera angle
To turn off the angle number display
Press CLEAR.
Press ANGLE while playing a scene
recorded with multiple angles.
1
CLEAR
While playing a scene recorded with
ANGLE
multiple angles, the angle icon (
flashes in the DVD display.
Press the ANGLE button while the
angle icon is flashing.
)
Notes
• You can change the camera angle during still playback. The
camera angle changes to the new setting when you resume
normal playback.
e.g.
• If you pause a picture immediately after changing a camera
angle, the resumed playback picture may not display the
new camera angle.
1
2
3
Press ANGLE or
/
while the angle
number is displayed on the TV screen.
2
Each time you press the ANGLE
button or the buttons, the
camera angle changes.
ANGLE
/
ENTER
You can change the camera angle directly by
pressing the number buttons corresponding to its
angle number instead of using the buttons.
/
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting Subtitles
You can display subtitles on the TV screen and select a subtitle language
from those included on the DVD video disc.
/ / / / ENTER
Good evening!
Bonsoir!
¡Buenas tardes!
SUBTITLE
DVD-V VCD
CD
Selecting a subtitle language
To turn subtitles on or off
1 Press SUBTITLE during playback.
Press SUBTITLE during playback.
1
The current subtitle setting is
displayed.
SUBTITLE
SUBTITLE
e.g.
2 Press
/
while the subtitle setting is displayed on
the TV screen, to select “On” or “Off.”
Off
ENG1
ENTER
FRE1
SP
A1
The abbreviation of the language appears instead
of the language name. Refer to the list of
languages and their abbreviations. 65
Notes
• Some DVD video discs are set to display subtitles
automatically, and you cannot turn them off even if you set
the subtitle function to off.
• During some scenes, the subtitles may not appear
immediately after you select “On.”
Press SUBTITLE or
/
while the
2
subtitle setting is displayed on the TV
screen.
• Some DVD video discs will allow you to make subtitle
selections and turn subtitles on or off only via the disc menu.
Each time you press the SUBTITLE
button or the buttons, the
SUBTITLE
/
subtitle languages included on the
DVD video disc change.
ENTER
To turn off the subtitle setting
display, press the ENTER button.
Notes
• When you turn on the DVD player or replace a disc, the player returns to the initial default setting 61
.
When you select a subtitle language which is not included on the disc, the DVD player plays a prior language programmed
on the disc.
• During some scenes, the subtitles may not appear immediately after you change the subtitle language.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Selecting a Language
You can select a preferred language and sound recording system from those
included on the disc.
2
CLEAR
Good morning!
¡Buenos días!
Bonjour!
1, 2
DVD-V VCD
CD
Selecting a playback audio setting
Selecting sound channels of VIDEO CDs
You can switch left and right channels by pressing the
Press AUDIO during playback.
1
The current audio setting is
displayed.
AUDIO
AUDIO button repeatedly during playback.
AUDIO
e.g.
E
E
NG1 PCM 2CH
D 2CH
Notes
• When you turn on the DVD player or replace a disc, player
returns to the initial default setting 61
NG
2
.
If you select a sound track which is not included on the disc,
the DVD player plays a prior sound track programmed on
the disc.
• Some discs allow you to change audio selections only via
the disc menu. If this is the case, press the MENU button
and choose the appropriate language from the selections on
the disc menu.
The abbreviation of the language appears instead
of the language name. Refer to the list of
languages and their abbreviations. 65
Press AUDIO or
/
while the audio
setting is displayed on the TV screen.
2
Each time you press the AUDIO
AUDIO
button or the
/
buttons, the audio
settings included on the disc
change.
ENTER
If you press the
/
buttons, you can select
output sound format. 59
To turn off the audio setting display, press the
CLEAR button.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Output sound conversion table (sampling frequency/quantization bit)
Audio selection from the menu
“Bitstream”
and output jacks on the rear panel
“PCM”
56 59
Sound recording system
Discs
BITSTREAM/PCM jack
2CH AUDIO OUT jacks
BITSTREAM/PCM jack
2CH AUDIO OUT jacks
Dolby Digital
48 kHz/16 bit
48 kHz/20 bit
Bitstream
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
Bitstream
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
–
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
–
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
–
Linear
PCM
48 kHz/24 bit
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
DVD
video discs
DTS
MPEG1, MPEG2
MPEG1
Linear PCM 44.1 kHz/16 bit
DTS
Bitstream
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
Bitstream
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
(Noise)
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
(Noise)
VIDEO CDs
Audio CDs
44.1 kHz/16 bit
44.1 kHz/16 bit
Bitstream
: 3D (N-2-2) sound enhancement can function.
(Signals are depressed by down sampling
process.)
• Signals of 96kHz from the BITSTREAM/PCM jack are depressed to 48 kHz by down sampling process when:
– “3D (N-2-2)” is selected. 39
– “PCM Down Sampling” is set to “On.” 59
– a copyright protected disc is played.
• Quantization bit of signals of 20 bit or higher is 16 bit if they are in a copyright protected disc.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick control
Simple use of a single button and the cursor control
enables you to direct your playback, without manipulating
many actual buttons.
Using the Graphic Remote
Control - V-REMOTE -
Selecting the Playback Function
- QUICK -
Accessing Features
- NAVI -
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick control
Using the Graphic Remote Control
1
2
- V-REMOTE -
Pressing one button can display a graphics based on-screen remote control that
allows you to control playback as if you were doing it from the actual remote
control.
DVD-V VCD
CD
Using the graphic remote control
Icons and features
See the pages in
During playback, press V-REMOTE.
for details on the features.
Function
V-REMOTE
1
The graphic remote control (Virtual
Remote) appears.
For the meaning of each icon, see
right.
Icon
Page
*
Current title/track number
–
–
–
*
*
Current chapter number
Elapsed time of the current title/track
Audio setting
DVD-V
e.g.
:
:
1
1
1 25 30
**
**
**
42
41
40
29
28
29
Subtitle setting
Angle setting
Reverse slow motion playback
Pause / Frame by frame playback
To begin slow motion playback
Press
and press ENTER.
/
/
/
to select the icon,
Playback starts from the beginning of
the current chapter or track.
31
26
31
2
Normal playback
ENTER
To locate succeeding chapters or
tracks.
28
27
28
Fast reverse playback
To stop playback.
Fast forward playback
To turn off the Virtual Remote.
To turn off the Virtual Remote
Press V-REMOTE.
V-REMOTE
* You can access a desired location. After step 2,
perform the steps below:
Note
Some discs may not permit this operation.
/
: steps 3 to 5 on 31
34
: steps 2 and 3 on
** After step 2, a sub menu will appear. Perform step 2
on the page in
.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Playback Function - QUICK -
1
Pressing one button can display a list of playback functions which are relevant to
your current playback mode.You can check and modify them from the list.
2 - 5
DVD-V VCD
CD
Selecting the playback function
During playback, press QUICK.
Press ENTER.
ENTER
1
5
The following on-screen display
appears.
(The actual display will vary
depending on the playback status.)
The on-screen display disappears
and playback will resume according
to your selection.
QUICK
e.g.
DVD-V
Quick menu
Memory :
Repeat :
Quick
Memory
Repeat
A–B (Set A)
Random
Bit Rate
Text
To program memory playback. 36
To select the repeat playback mode.
For the mode selections, see page 35
.
A-B (Set A) : At the beginning of a segment you want
to repeat, press the ENTER button. Then
at the end of the segment, press the
Exit
ENTER button again. The segment is
35
played repeatedly.
Press
/
to select a desired item.
e.g. To change the repeat mode:
Random :
Bit Rate :
To select the random playback mode.
For the mode selections, see page
To activate the bitrate display.
2
37
.
ENTER
(Bit rate: data transfer rate (Mbit/s)
Quick
Memory
Repeat
A–B (Set A)
Random
Bit Rate
Text
Amount of picture, sound and subtitle
data in the DVD video disc transferred
per second.
The larger the value, the more data
Exit
processed, but this does not necessarily
insure better picture quality.)
To activate the Text display.
Text display:
Displays DVD-Text data or CD-Text data
if included on the disc.
(Some content on the disc may not be
displayed properly depending on the
disc.)
Text :
Exit :
Press ENTER.
3
4
e.g. The mode menu appears.
ENTER
Chapter Repeat
Title Repeat
All Repeat
Repeat Off
To quit the on-screen display.
Note
Pressing the QUICK button again also exits the on-screen
display.
Press
/
to change the setting.
e.g. To select the title repeat
mode:
ENTER
Chapter Repeat
Title Repeat
All Repeat
Repeat Off
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick control
Accessing Features - NAVI -
1
2, 3
The NAVI menu provides an icon based display from which you can easily
access key playback function or setting.
DVD-V VCD
CD
NAVI menu items
To exit the NAVI menu
Press NAVI.
Press NAVI.
1
The NAVI menu appears.
NAVI
NAVI
e.g.
DVD-V
Alternatively press
/
to remove the highlight from an
icon to the center position, and press ENTER.
ENTER
Exit
Press
/
/
/
to select a desired
Note
Depending on the disc, some features cannot be accessed.
2feature icon.
For details on each feature, refer to
the list on the next page.
ENTER
Press ENTER.
3
ENTER
Selection details appears.
Refer to the list on the next page and
4follow the instructions detailed on
subsequent pages.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Navi menu selections
You can divide a desired scene into stop action frames for careful
analysis.
50
56
50
51
51
Strobe Viewer
You can change the default settings to customize performance to
your preference.
Setup
You can display thumbnail views of the first scenes of titles or
chapters and select a preferred one.
Preview
You can sample a scene from a playback picture and transform it
into a background picture.
Capture
You can display all camera angles simultaneously and select your
preferred one from them.
Angle Viewer
Picture Setting
E.A.M.
You can fine adjust picture quality and store up to 3 custom picture
settings in the memory of the DVD player.
52
39
You can easily switch a preferred audio enhancement.
You can control key playback functions using the graphics based
on-screen remote control.
46
53
V-Remote
Display
You can view information about a disc and its operational status on
the TV screen.
You can display closed caption included on a DVD disc without
connecting a closed caption decoder to your TV.
53
Closed Caption
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick control
Accessing Features - NAVI - (continued)
NAVI menu items
Strobe Viewer
Preview
You can divide a desired scene into
stop action frames for careful
analysis.
You can display thumbnail views of
the first scenes of titles or chapters
and select a preferred one.
After selecting this icon and pressing ENTER, the
following on-screen display appears:
After selecting this icon and pressing ENTER, the
following on-screen display appears:
e.g.
e.g.
1
2
3
4
5
6
Slow
Normal
>>
Fast
Title
Chapter
>>
Interval
<<
Strobe Viewer
Preview
1 Press
/
/
/
to select.
1 Press
/
/
/
to select.
ENTER
ENTER
Slow: Still pictures at shorter intervals.
Normal: Still pictures at normal intervals.
Fast: Still pictures at longer intervals.
1 - 6:
Title:
To locate the scene.
To display the first scenes of titles (1 to 6).
Chapter: To display the first scenes of chapters
(1 to 6).
Interval: To display scenes at intervals of about 10
minutes apart.
>>:
To view the next series of 6 pictures.
To quit the on-screen display.
:
2 Press ENTER.
<< :
>> :
:
To go to the previous page.
To go to the next page.
To quit the on-screen display.
ENTER
2 Press ENTER.
ENTER
Note
Some discs or scenes may not permit this operation.
Notes
• Some discs or scenes may not permit this operation.
• Some items may not be selected depending on the
disc or scene.
• Some of the first scenes may not picked up depending
on the disc.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Capture
Angle Viewer
You can sample a scene from a
playback picture and transform it into
a background picture.
You can display all camera angles
simultaneously and select your
preferred one from them.
After selecting this icon and pressing ENTER, the
following on-screen display appears:
After selecting this icon and pressing ENTER, the
following on-screen display appears:
e.g.
e.g.
1
2
5
8
3
6
9
Capture
Storing
Exit
4
7
Angle Viewer
When the scene contains 9 camera angles:
1 Press to select.
1 Pause playback at a scene you want to capture.
/
/
/
2 Press
/
to select.
ENTER
ENTER
1-9 : To select the camera angle.
: To quit the on-screen display.
Storing: To sample and store the current picture
in the player memory.
2 Press ENTER.
Exit:
To quit the on-screen display.
ENTER
3 Press ENTER.
ENTER
Note
Some discs or scenes may not permit this operation.
The stored picture will be displayed as a
background picture when the player is in the stop
mode. It is necessary to confirm this process via
the setup menu 62
.
Notes
• You can store only one picture. Storing a new picture
will erase the old one.
• No operations are permitted in process of sampling
and storage of background picture.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick control
Accessing Features - NAVI - (continued)
NAVI menu items
Picture Setting
3 Press ENTER.
You can fine adjust picture quality
The sub menu appears.
and store up to 3 custom picture
settings in the memory of the DVD
player.
4 Press
/
to adjust the value, and press ENTER.
e.g.
+
2
Color
After selecting this icon and pressing ENTER, the
following on-screen display appears:
e.g.
Contrast :
Brightness :
Color:
-7 (Lower) to +7 (Higher)
-7 (Darker) to +7 (Brighter)
-7 (Duller) to +7 (Brighter)
-7 (Redder) to +7 (Greener)
On / Off
1
2
3
Tint :
DNR*1 :
Edge Enhance*2 : On / Off
All Reset :
To restore all the elements to
the normal setting. A message
will appear. Follow the
procedure displayed on-screen.
*1: DNR: Digital Noise Reduction.
1 Press
/
to select, and press ENTER.
To view a picture with less video noise.
Notes
ENTER
• Actual picture enhancement may vary depending
on the quality of the disc.
• While the DNR feature can provide additional
improvement in the reduction of noise in the video
signal, it may produce undesirable picture artifacts
on some discs.
• Depending on the disc, some kinds of picture
details may be lost by the picture enhancement.
(Standard) : Normal setting.
1, 2, 3:
Select the desired custom
memory number. (Follow steps
2 to 4 below.)
*2: To enhance picture edges.
2 Press
/
to select the element.
Note
e.g. When you select “Color”:
The Tint adjustment is not available when connecting to a
TV via the component video jacks (Y, PB, PR).
Picture Setting
+1
–1
0
Contrast
Brightness
Color
Tint
0
DNR
Edge Enhance
All Reset
Off
Off
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
Closed Caption
You can display closed caption
You can view information about a
disc and its operational status on the
TV screen.
included on a DVD disc without
connecting a closed caption decoder
to your TV.
After selecting this icon and pressing ENTER, the
following on-screen display appears:
After selecting this icon and pressing ENTER, the
following on-screen display appears:
e.g.
e.g.
On
Off
Title : 1
Chapter : 23
Time : 1:23:45
Audio : ENG 1
Subtitle : ENG 1 On
Angle : 1/3
D 2CH
E.A.M. : Normal
Audio Out Select : Bitstream
Zoom : Off
Chapter repeat
1 Press
/
to select.
To quit the on-screen display, press ENTER.
ENTER
Note
Some discs or scenes may not permit this operation.
On : To display closed caption.
Off: To disable closed caption.
2 Press ENTER.
ENTER
Notes
• While you are using on-screen displays (including the
above one), you cannot view closed caption.
• When “On” is selected, some displays such as “
be disabled.
” may
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Setup
You can change the default settings to customize
performance to your preference.
Customizing the Function
Settings
Table of Languages
Download from Www.Somanuals.com. All Manuals Search And Download.
1, 6
Customizing the Function Settings
You can change the default settings to customize performance to your
preference.
2, 3, 4
RETURN
DVD-V VCD
CD
Setting procedure
Press
/
to select the setting you
Press SETUP during stop.
want to change, then press ENTER.
1
2
3
4
The following on-screen display
appears.
SETUP
ENTER
Picture
TV Shape
4:3 LB
Progressive 4:3 Output Full
Progressive Conversion Auto
Change the selection by
buttons, by referring to the
corresponding pages 58 , then press
ENTER.
/
or other
Press
/
to select a symbol for the
setting you want to change.
(See the next page.)
ENTER
ENTER
Repeat steps 3 and 4 to change other
settings.
To select another operation, go back to step 2.
5
6
Picture performance settings
Press SETUP.
SETUP
The on-screen display disappears.
Output sound settings
Language settings
Display settings
Operational settings
Initializing
To return to the previous display
Press RETURN.
RETURN
Notes
• The on-screen display disappears also when you select “
and press the ENTER button.
• The SETUP button can function even during normal
playback, however some operations may be inaccessible,
and a message will appear. In this case, try again after
playback is stopped.
”
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Details
Page
TV Shape
To select a picture size according to the aspect
ratio of your TV.
58
58
DVD-V
DVD-V
VCD
Progressive 4:3 Output
To select the video output of pictures recorded
in 4:3 format. (Only when connected to a
PROGRESSIVE TV.)
DVD-V
Progressive Conversion
PCM Down Sampling
To select the system of output signal. (Only
when connected to a PROGRESSIVE TV.)
58
59
DVD-V
To select a sound processing option according
to performance of the connected equipment.
(Only when the BITSTREAM/PCM (DIGITAL)
AUDIO OUT jack is connected.)
DVD-V VCD
CD
Audio Out Select
To select an output sound format corresponding 59
to your system connection.
Dynamic Range Control
To turn on or off a function that makes faint
sounds easier to hear even if you lower the
volume during late hours playback.
59
DVD-V
DVD-V
Karaoke Vocal
To turn on or off the vocal output during DVD
KARAOKE disc playback.
60
DVD-V VCD
CD
On-Screen Language
Disc Menu Language
Audio Language
To select a preferred language for on-screen
displays.
60
60
61
61
DVD-V
DVD-V
DVD-V
To select a preferred language for disc menus.
To select a preferred language for the sound
track.
Subtitle Language
To select a preferred language for subtitles.
DVD-V VCD
CD
On-Screen Displays
Background
To turn on or de-activate the operational status
display on the TV screen.
62
62
62
DVD-V VCD
CD
To select the background color or background
picture.
DVD-V
Screen Saver
To turn the screen saver on or off.
DVD-V
DVD-V
Pause/Still
To select the resolution of still pictures.
(Field/Frame)
62
62
64
Parental Lock
To turn the parental lock function on or off.
DVD-V VCD
CD
Remote Confirmation
To turn on or off the confirmation beeper
announcing when each remote command
received.
DVD-V
VCD
Title Stop
PBC
To turn on or off a feature that automatically stops 64
playback after a title has been viewed.
To use the menu screen when playing a PBC-
controllable VIDEO CD.
64
Initialize
To restore all settings to the factory set.
64
DVD-V VCD
CD
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the Function Settings (continued)
Setting details
DVD-V VCD
Progressive 4:3 Output
Picture
Select the video output of pictures recorded in 4:3
format. (Only when connected to a PROGRESSIVE
TV.)
TV Shape
4:3 LB
Progressive 4:3 Output Full
Progressive Conversion Auto
Full: Displays pictures expanded horizontally to fill
the 16:9 screen.
4:3: Displays images in 4:3 aspect ratio with
masking bars to the left and right of the picture.
DVD-V
TV Shape
4:3 Letterbox:
Select when a standard 4:3 TV is
connected.
DVD-V
Progressive Conversion
Displays theatrical images with
masking bars above and below the
picture.
There are two types of source content in pictures
recorded in DVD video discs: film content (pictures
recorded from films at 24 frames per second) and
video content (video signals recorded at 30 frames
per second). Make this selection according to the
type of content being viewed.
4:3 Normal:
Select when a standard 4:3 TV is
connected.
Displays pictures cropped to fill
your TV screen. Either or both
sides of the picture are cut off.
Auto: Select this position normally.
The DVD player automatically detects source
content, film or video, of playback source, and
converts that signal in the progressive output
format in an appropriate method.
16:9 Widescreen: Select when a 16:9 wide TV is
connected.
Video: The DVD player filters video signal, and
converts it in the progressive output format
appropriately.
Notes
• The displayable picture size is preset on the DVD video
disc. Therefore, the playback picture of some DVD
video discs may not conform to the picture size you
select.
Suitable for playback of video content
pictures.
• When you play DVD video discs recorded in the 4:3
picture size only, the playback picture always appears
in the 4:3 picture size regardless of the TV shape
setting.
• If you select “16:9 Widescreen” and you own a 4:3 TV
set, the DVD playback picture will be horizontally
distorted during playback. Images will appear to be
horizontally compressed. Always be sure that your TV
shape conforms to the actual TV in use.
Film: The DVD player converts film content pictures
in the progressive output format appropriately.
Suitable for playback of film content pictures.
The progressive output feature will be most
effective under this selection.
Note
Depending on the disc, pictures may be cut off or
doubled. In this case, select “Video.”
58
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD-V VCD
CD
Audio Out Select
Audio
PCM Down Sampling
Audio Out Select
Off
Bitstream
Select the output sound format corresponding to your
system connection.
Dynamic Range Control On
Karaoke Vocal
Off
43
For details of sound recording systems, see
.
Bitstream:
Select when connected to an amplifier
equipped with a Dolby Digital, DTS,
21 22
MPEG1 or MPEG2 decoder.
The DVD player outputs digital audio
information in the bitstream format
when you play a DVD video disc
recorded on the Dolby Digital, DTS,
MPEG1 or MPEG2 recording system.
DVD-V
PCM Down Sampling
Make this selection only when you use your audio
equipment (e.g. receiver) connecting to the DVD
player via the BITSTREAM/PCM (DIGITAL) AUDIO
OUT jack.
PCM:
Select when connected to a 2 channel
23
digital stereo amplifier.
According to performance of your connected receiver,
select a sound processing option for playback of a
disc that contains high frequency signals (sampling
frequency 96 kHz).
The DVD player outputs sounds in the
PCM 2ch format when you play a DVD
video disc recorded on the Dolby
Digital, MPEG1 or MPEG2 recording
system.
Off: Select when your connected receiver conforms
to high frequency signals of 96 kHz.
Note
The DVD player outputs these signals in a disc
as they are.
On: Select when your connected receiver does not
conform to high frequency signals of 96 kHz.
The DVD player outputs these signals in a disc
depressing the frequencies to 48 kHz.
When you make a connection to a TV, or Dolby Pro
Logic or stereo system via the analog audio jacks, select
“Bitstream” or “PCM.”
DVD-V
Dynamic Range Control
Notes
Off: Full dynamic range is maintained.
On: Dynamic range is reduced.
• Regardless of this setting, the DVD player outputs high
frequency signals in a copyright protected disc,
depressing to 48 kHz.
• If you select “Off” while your connected receiver does
not conform to high frequency signals of 96 kHz, you
cannot hear output sound of those signals.
Notes
• This function works only during playback of Dolby
Digital recorded discs.
• The level of Dynamic Range Reduction may differ
depending on the DVD disc.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the Function Settings (continued)
Setting details
DVD-V
Karaoke Vocal
Language
Off: The primary vocal is not output.
On: The primary vocal is output when it is recorded
on the disc.
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
Subtitle Language
ENG
– – –
Notes
• The vocal output feature is used during playback of
Dolby Digital (multi-channel) recorded DVD KARAOKE
discs. This feature allows you to turn off vocal audio
tracks, or restore them for background accompaniment.
• When playing KARAOKE, connect appropriate audio
equipment such as an amplifier to the DVD player.
DVD-V VCD
CD
On-Screen Language
English: To view on-screen displays in English.
Français:To view on-screen displays in French.
Español: To view on-screen displays in Spanish.
DVD-V
Disc Menu Language
English: To display disc menus in English.
French: To display disc menus in French.
Spanish: To display disc menus in Spanish.
Others: To make a further choice.
After pressing the ENTER button, follow
steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 65
.
2) Select the first character by pressing the
buttons.
/
3) Press the
/
buttons to shift and select the
second character by pressing the
/
buttons.
Language
On-Screen Language ENG
Disc Menu Language ENG
English
French
Spanish
Others
Audio Language
Subtitle Language
ENG
– – –
Code
S
E
4) Press the ENTER button.
Note
Some DVD video discs may not include your pre-
selected language. In this case, the DVD player
automatically displays disc menus consistent with the
disc’s initial language setting.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Press the
/
buttons to shift and select the
DVD-V
Audio Language
second character by pressing the
/
buttons.
English: To play sound tracks in English.
French: To play sound tracks in French.
Spanish: To play sound tracks in Spanish.
Others: To make a further choice.
After pressing the ENTER button, follow
steps 1) - 4) below.
C
Language
On-Screen Language ENG
Disc Menu Language ENG
English
French
Spanish
No Subtitle
Others
Audio Language
Subtitle Language
ENG
– – –
1) Obtain the abbreviation of the preferred
Code
A
A
language from the list 65
.
2) Select the first character by pressing the
buttons.
/
4) Press the ENTER button.
3) Press the
/
buttons to shift and select the
second character by pressing the
/
buttons.
Notes
• Some DVD video discs may be set to display subtitles
in a different language than you selected. A prior
subtitle language may be programmed on the disc.
• Some DVD video discs allow you to change subtitle
selections only via the disc menu. If this is the case,
press the MENU button and choose the appropriate
subtitle language from the selection on the disc menu.
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
Subtitle Language
English
French
Spanish
Others
ENG
– – –
Code
S
E
4) Press the ENTER button.
Note
Some DVD video discs may be played in a different
language than you selected. A prior language may be
programmed on the disc.
DVD-V
Subtitle Language
English:
French:
Spanish:
To display subtitles in English.
To display subtitles in French.
To display subtitles in Spanish.
No Subtitle: To disable subtitles.
Others:
To make a further choice.
After pressing the ENTER button, follow
steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 65
.
2) Select the first character by pressing the
buttons.
/
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the Function Settings (continued)
Setting details
Operation
Display
Pause/Still
Parental Lock
Remote Confirmation On
Auto
Off
On-Screen Displays On
Background
Screen Saver
Gray
On
Title Stop
PBC
Off
On
DVD-V VCD
CD
DVD-V
On-Screen Displays
Pause/Still
Off: Operational modes (e.g. “ ”, “
displayed.
On: Operational modes (e.g. “ ”, “
displayed on-screen.
”) are not
”) are
Auto:
For normal use. Still and fast motion images
can be paused.
Frame: The resolution of still pictures is improved,
so that you can make a motionless picture
more clearer when you pause it.
DVD-V VCD
CD
Background
DVD-V
Parental Lock
Blue:
Gray:
Blue background.
Gray background.
DVD video discs equipped with the parental lock
function are rated according to their content. The
contents allowed by a parental lock level and the way
a DVD video disc can be controlled may vary from
disc to disc. For example, if the disc allowed you
could edit out violent scenes unsuitable for children
and replace them with more suitable scenes, or lock
out playback of the disc altogether.
Capture: To use a picture you sampled and stored in
the memory using the Capture feature 51
as a background.
Jacket: To use the jacket picture included on some
discs as a background. If it is not included,
a gray background will be substituted.
DVD-V
Screen Saver
• DVD video discs may or may not respond to the
parental lock settings. This is not a defect in the DVD
player. Make sure this function works with your DVD
video discs.
Off: The screen saver is disengaged.
On: The screen saver operates.
Off: The parental lock feature does not function.
After pressing the ENTER button, follow step 1)
below.
On: To activate the parental lock feature or change
the settings.
After pressing the ENTER button, follow steps
1) - 3) below.
Parental Lock
Security Code
– – – –
62
Download from Www.Somanuals.com. All Manuals Search And Download.
1) Press the number buttons to create a personal
4-digit security code, then press the ENTER
button.
3) Press the
/
buttons to select the parental
lock level, then press the ENTER button.
If you make a mistake before pressing the
ENTER button, press the CLEAR button and
enter your 4-digit security code again.
Parental Lock
U
7
S
Area Code
Level
2) Enter the code of a country/area whose
standards were used to rate the DVD video
disc, referring to the list below.
Country/Area
AUSTRALIA
BELGIUM
CANADA
CHINA
CHINA HONG KONG
DENMARK
FINLAND
Code
AU
BE
CA
CN
HK
DK
FI
FR
DE
ID
IT
JP
MY
NL
NO
PH
RU
SG
ES
SE
CH
TW
TH
GB
US
You cannot play DVD video discs rated higher than
the level you selected unless you cancel the parental
lock function.
For example, when you select level 7, discs rated
higher than level 7 are locked out and cannot be
played.
The parental lock level is equivalent to the following
FRANCE
USA movie ratings.
Level 7: NC-17
Level 6: R
Level 4: PG 13
Level 3: PG
GERMANY
INDONESIA
ITALY
JAPAN
MALAYSIA
NETHERLANDS
NORWAY
PHILIPPINES
RUSSIAN FEDERATION
SINGAPORE
SPAIN
SWEDEN
SWITZERLAND
TAIWAN
THAILAND
UNITED KINGDOM
UNITED STATES
Level 1: G
The parental lock levels for other countries/areas
than U.S. are included for future use. Check the
appropriate parental lock level when you buy a DVD
video disc equipped with the parental lock feature in
the future.
To change the parental lock level
Follow steps 1) - 3).
To change your 4-digit security code
1) After selecting “On” or “Off,” press the STOP
button four times, then press the ENTER
button.
a) Select the first character by pressing the
buttons.
b) Press the
/
/
buttons to shift and select
ENTER
STOP
STOP
STOP
STOP
the second character by pressing the
buttons.
/
c) Press the ENTER button.
The 4-digit security code is cleared.
2) Press the number buttons to create a new
4-digit security code.
3) Press the ENTER button.
Note
After making the “Parental Lock” setting, the on-screen
display will disappear. To make other settings, press the
SETUP button again to display them.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the Function Settings (continued)
Setting details
DVD-V VCD
CD
Remote Confirmation
Initialize
All settings will be restored to pre-set
levels.
Exit
Yes
Off: The beeper does not sound.
On: The beeper sounds with each remote operation.
DVD-V
Title Stop
Off: The DVD player continues after playback of a
title is completed.
On: The DVD player stops after playback of a title is
completed.
DVD-V VCD
CD
Initialize
To restore all settings to the factory set.
1) Press the buttons to select “Yes,” and
/
VCD
PBC
press the ENTER button.
Off: When playing a VIDEO CD without using the
menu.
On: To use the menu when playing a PBC-featured
VIDEO CD.
ENTER
2) Read the message, and if you really want to
restore all settings, press the
/
buttons to
select “Yes,” and press the ENTER button.
ENTER
The message of completion appears.
Note
The “Parental Lock” setting is not restored to the factory
set.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Languages
Table of languages and their abbreviations
Abbreviation
Language
Abbreviation
Language
Abbreviation
Language
– – –
No alternate
language
Chinese
Dutch
English
French
German
Italian
Japanese
Korean
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
CHI (ZH)
DUT (NL)
ENG (EN)
FRE (FR)
GER (DE)
ITA (IT)
JPN (JA)
KOR (KO)
MAY (MS)
SPA (ES)
AA
Sango
Malay
Spanish
Afar
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
IW
JI
SK
SL
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Belorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Yiddish
JW
KA
KK
KL
KM
KN
KS
KU
KY
LA
LN
LO
LT
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
LV
MG
MI
MK
ML
MN
MO
MR
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Irish
Scottish Gaelic
Galician
GL
Zulu
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Before Calling Service
Personnel
Specifications
LIMITED WARRANTY DVD
PLAYER
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Before Calling Service Personnel
Check the following guide for the possible cause of a problem before contacting service.
Symptoms and correction
Symptom
Cause
Correction
Page
No power.
• The power plug is disconnected.
• Connect the power plug securely into the
wall outlet.
18
The DVD player turned off by • The automatic power off function turned
• Press the PLAY button.
27
26
itself.
the unit off.
No picture.
• The TV is not set to receive DVD signal
output.
• Select the appropriate video input mode
on the TV so the picture from the DVD
player appears on the TV screen.
• The video cable is not connected securely. • Connect the video cable securely into the 18, 19
appropriate jacks.
No sound.
• The equipment connected with the audio
cable is not set to receive DVD signal
output.
• Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD player.
26
• The audio cable is not connected securely. • Connect the audio cable securely into
the appropriate jacks.
18-23
26
• The audio receiver or TV is turned off.
• Turn on the equipment connected with
the audio cable.
• The setting of output sound format is
incorrect.
• Select the proper audio setting.
42, 56
59
The playback picture has
occasional distortion.
• The disc is dirty.
• Eject the disc and clean it.
9
–
• It is in fast forward or fast reverse
playback.
• Sometimes a small amount of picture
distortion may appear. This is not a
malfunction.
Brightness is unstable or
noises are present in the
playback pictures.
• The effect of copy protection.
• Connect the DVD player directly to the
TV. Avoid connecting the DVD player to
a VCR or TV/VCR combination.
18
The DVD player does not
start playback.
• No disc is inserted.
• Insert a disc.
26
10
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc
type.)
• The disc is placed upside down.
• Place the disc with the playback side
down.
26
26
• The disc is not placed within the guide.
• Place the disc correctly inside the guide
on the disc tray.
• The disc is dirty.
• Clean the disc.
9
• The parental lock function is set.
• Cancel the parental lock function or
change the parental lock level.
56, 62
Playback does not follow the • It is in the mode of repeat playback,
• These operations may prevent a proper
progress of the contents.
–
–
course of the disc’s program.
memory playback, etc.
Buttons do not work.
• Power supply fluctuations or other
abnormalities such as static electricity may
interrupt correct operations.
• Turn the power on or off with the POWER
button. Or disconnect the power plug and
insert it into the wall outlet again.
The remote control does not
work properly.
• The remote control is not pointed at the
remote sensor of the DVD player.
• Point the remote control at the remote
sensor of the DVD player.
15
15
15
• The remote control is too far from the DVD • Operate the remote control within about
player.
7 m.
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
DVD player / outputs / supplied accessories
DVD player
Power supply
Power consumption
Mass
120 V AC, 60 Hz
17 W
3.0 kg
External dimensions
Signal system
Laser
430 × 81 × 311 mm (W/H/D)
Standard NTSC
Semiconductor laser, wavelength 650 nm / 780 nm
Frequency range
DVD linear sound : 48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
Signal-to-noise ratio
Audio dynamic range
Harmonic distortion
Wow and flutter
More than 112 dB
More than 108 dB
Less than 0.002 %
Below measurable level (less than ±0.001 % (W.PEAK))
Temperature: 5 °C to 35 °C, Operation status: Horizontal
Operating conditions
Outputs
Video output
1.0 V (p-p), 75 Ω, negative sync., pin jack × 1
S video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin × 1
(C) 0.286 V (p-p), 75 Ω
Component video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., pin jack × 1
(PB)/(PR) 0.7 V (p-p), 75 Ω, pin jack × 2
Audio output (BITSTREAM/PCM
OPTICAL)
Optical connector × 1
Audio output (BITSTREAM/PCM
COAXIAL)
0.5 V (p-p), 75 Ω, pin jack × 1
2.0 V (rms), 220 Ω, pin jacks (L, R) × 1
Audio output (2CH AUDIO)
Supplied Accessories
Audio/video cable ................................................. 1
Remote control (SE-R0058) ................................. 1
Batteries (AA) ....................................................... 2
Power cord ........................................................... 1
• Designs and specifications are subject to change without notice.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
LIMITED WARRANTY DVD PLAYER
Toshiba America Consumer Products, Inc. (“TACP”), Toshiba Hawaii (“THI”) and Toshiba Canada Limited (“TCL”) make the
following limited warranties. These limited warranties extend to original purchaser or any person receiving this set as a gift
from the original purchaser and to no other purchaser or transferee.
Limited Ninety (90) Day Warranty
Commercial Units
TACP/THI warrant this product against defects in materials
or workmanship for a period of ninety (90) days after the
date of original retail purchase. During this period, TACP/
THI will repair or replace a defective product or part, at their
option, with a new or refurbished product or part without
charge to you.You must deliver the entire product to a
TACP/THI Authorized Service Station. You are responsible
for all transportation and insurance charges for the unit to
and from the Authorized Service Station. If you live in the
U.S.A. you may, at your option, return your DVD Unit to:
Toshiba America Consumer Products Inc.
Products sold and used for commercial use have a limited
ninety (90) day warranty for all parts and labor.
Owner’s Manual
You should read the owner’s manual thoroughly before
operating this product.You should complete and mail the
enclosed Demographic card within ten (10) days after you,
or the person who has given you this product as a gift,
purchased this product. This is one way to enable TACP to
provide you with better customer service and improved
products. Failure to return the card will not affect your rights
under this warranty.
Returns Center
1420C Toshiba Dr.
Lebanon, TN 37087
Your Responsibility
Upon receipt we will, at our option, exchange the DVD Unit
with a new or refurbished unit. Canadian consumers are
requested to contact TCL. In Hawaii consumers are
requested to contact THI.
The above warranties are subject to the following
conditions:
(1) You must retain your bill of sale or provide other proof of
purchase.
(2) You must notify a TACP/THI/TCL /Authorized Service
Station within thirty (30) days after you discover a
defective product or part.
(3) All warranty servicing of this product must be made by a
TACP/THI/TCL Authorized Service Station.
(4) U.S.A. warranties are effective only if the product is
purchased and operated in the Continental U.S.A. or
Puerto Rico.
(5) Labor service charges for set installation. Set up,
adjustment of customer controls and installation or
repair of antenna systems are not covered by this
warranty. Reception problems caused by inadequate
antenna systems are your responsibility.
(6) Warranties extend only to defects in materials or
workmanship as limited above and do not extend to any
product or parts which have been lost or discarded by
you or to damage to products or parts caused by
misuse, accident, damage caused by Acts of God, such
as lighting or fluctuations in electric power, improper
installation, improper maintenance or use in violation of
instructions furnished by us; or to units which have
been altered or modified without authorization of TACP/
THI/TCL or to damage to products or part thereof which
have had the serial number removed, altered, defaced
or rendered illegible.
Limited One (1) Year Warranty
TACP/THI further warrant the parts in this product against
defects in materials or workmanship for a period of one (1)
year after the date of original retail purchase. During this
period, TACP/THI will repair or replace a defective product
or part, at their option, with a new or refurbished product or
part without charge to you, except that if a defective part is
replaced after ninety (90) days from the date of the original
retail purchase you pay labor charges involved in the
replacement.You must also deliver the entire product to a
TACP/THI Authorized Service Station. You are responsible
for all transportation and insurance charges for the unit to
and from the Authorized Service Station. If you live in the
U.S.A. you may, at your option, return your DVD Unit to:
Toshiba America Consumer Products Inc.
Returns Center
1420C Toshiba Dr.
Lebanon, TN 37087
Upon receipt we will, at our option, exchange the DVD Unit
with a new or refurbished unit. Canadian Consumers are
requested to contact TCL. In Hawaii consumers are
requested to contact THI.
Rental Units
The warranty for rental units begin with the first rental or
thirty (30) days from the date of shipment to the rental firm,
whichever comes first.
(7) Should you elect to return your DVD Unit to TACP after
the ninety (90) days and within one (1) year, or after the
warranty period has expired: Call (800)-631-3811 to
receive information concerning an exchange price.
Payment must be enclosed with product in the form of a
certified check or money order including reason for
return.
(8) Physically damaged DVD Units are not acceptable for
repair or exchange whether in or out of warranty and
will be returned as received.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Obtain Warranty Service
(1) Refer to the troubleshooting guide in your owner’s manual. This check list may solve your problem.
(2) In the U.S.A., only call the TACP toll free number 800-631-3811, or if in Hawaii or Canada see listing below within (30)
days after you find a defective product or part.
(3) Arrange for the delivery of the product to the TACP/THI/TCL Authorized Service Station or TACP Return Center.
Products shipped to the Service Station must be insured and safely and securely packed, preferably in the original
shipping carton, and a letter explaining the defect and also a copy of the bill of sale or other proof of purchase must be
enclosed.
In Canada contact:
Consumer Electronics Group
191 McNabb Street
Markham, Ontario L3R 8H2
(905)-470-5400
In the Continental United States contact:
In Hawaii contact:
Toshiba Hawaii Inc.
327 Kamakee Street
Honolulu, HA 96814
(808)-521-5377
Consumer Electronics Group
22171 Fraserwood Way
Richmond, B.C. V6W 1J5
(604)-303-2500
Toll Free
800-631-3811
Consumer Electronics Group
1643 North Service Road
Droval, QC H9P 1J1
(514)-856-4100
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose, are
expressly limited to the duration of the limited warranties set forth above. With the exception of any warranties implied by state
law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties, guarantees, agreements and
similar obligations of manufacturer or seller with respect to the repair or replacement of any parts. In no event shall TACP/THI
be liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in
any manner whatsoever. The time within which an action must be commenced to enforce any obligation of TACP/THI arising
under the warranty or under any statute, or law of the United States or any state thereof, is hereby limited to ninety (90) days
from the date you discover or should have discovered, the defect. This limitation does not apply to implied warranties arising
under state law.
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. Some
states do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the exclusion or
limitation of incidental or consequential damages, so the above provisions may not apply to you.
ATTENTION CANADIAN CONSUMERS:
Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed, and forward
this completed form with a copy of bill of sale to TOSHIBA OF CANADA to “Register and Validate” their warranty. Product
must be purchased from an Authorized Canadian Dealer. Products purchased in the U.S.A. and used in Canada are not
covered by these warranties.
IMPORTANT: PACKING AND SHIPPING INSTRUCTION
When you send the product to a Service Station, you must use the original carton box and packing material, then insert the
original carton box containing the unit into another carton using more packing material.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|