Introduction
Connections
2
16
24
32
50
60
DIGITAL VIDEO
Basic playback
Advanced playback
Function setup
Others
DVD VIDEO PLAYER
SD-3980SU
SD-3980SC
OWNER’S MANUAL
© 2004 Toshiba Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
The instructions shall state that an ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm
in each pole shall be incorporated in the electrical installation of the building.
CAUTION:
These servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock do not perform any servicing other than that contained in the
operating instructions unless you are qualified to do so.
In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD
video player.
Model No.
Serial No.
Retain this information for future reference.
Location of the required label
MANUFACTURED
SERIAL NO.
Be aware that this equipment is still powered even after the ON/STANDBY indicator turns off (standby
mode) by pressing the ON/STANDBY button. To disconnect this equipment completely from the mains
power, pull out the power plug from the wall outlet.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS
OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR
FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in
electric shock or fire hazard.The safeguards incorporated in this unit will protect you if you observe the
following procedures for installation, use and servicing.This unit is fully transistorized and does not
contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11.Only use attachments/accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
S3125A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
IMPORTANT SAFETY INSTRUCTIONS
13.Unplug this apparatus during lightning storms or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
ADDITIONAL SAFETY INSTRUCTIONS
15.When you use headphones, keep the volume at a moderate level. If you use the headphones continuously
with high volume sound, it may cause hearing damage.
16.Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a
risk of fire or electric shock.
17.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
18.Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious
personal injury.
19.Do not place a heavy object on or step on the apparatus. The object may fall, causing serious personal
injury and serious damage to the apparatus.
20.Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and apparatus malfunction.
21.If the apparatus should smoke or smell, immediately disconnect the power cord from the wall outlet. Wait
until the smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause
fire.
22.While it is thundering, do not touch the connecting cables or the apparatus.
23.The apparatus includes lead, an ingredient of solder used on the PCB, which is a harmful substance to
human and the environment. When disposing of this apparatus, follow the rules and regulations in your
area.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Precautions
Notes on handling
Notes on moisture condensation
When shipping the DVD video player, the original
shipping carton and packing materials come in handy.
For maximum protection, repack the unit as it was
originally packed at the factory. Take care not to give
it a shock or shake when carrying.
Do not use volatile liquids, such as insect spray, near
the DVD video player. Do not leave rubber or plastic
products in contact with the DVD video player for a
long time. They will leave marks on the finish.
The top and rear panels of the DVD video player may
become warm after a long period of use. This is not a
malfunction.
Moisture condensation damages the DVD video player.
Please read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts of
the DVD video player.
When the DVD video player is not in use, be sure to
remove the disc and turn off the power.
If you do not use the DVD video player for a long
period, the unit may not function properly in the
future.Turn on and use the DVD video player
occasionally.
Moisture condensation occurs during the following
cases.
When you bring the DVD video player directly from a
cold place to a warm place.
When you use the DVD video player in a room where
you just turned on the heater, or a place where the
cold wind from the air conditioner directly hits the
unit.
In summer, when you use the DVD video player in a
hot and humid place just after you move the unit from
an air conditioned room.
Notes on locating
Place the DVD video player on a level surface. Do not
use it on a shaky or unstable surface such as a
wobbling table or inclined stand. The loaded disc may
come off the proper position and cause damage to
the DVD video player.
When you place this DVD video player near a TV,
radio, or VCR, the playback picture may become poor
and the sound may be distorted. In this case, place
the DVD video player away from the TV, radio, or
VCR.
When you use the DVD video player in a humid place.
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry.
Do not use the DVD video player when moisture
condensation may occur.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the DVD
video player.
If you use a chemical saturated cloth to clean the
unit, follow that product’s instructions.
If you use the DVD video player in such a situation, it
may damage discs and internal parts. Remove the
disc, connect the power cord of the DVD video player
to the wall outlet, turn on the DVD video player, and
leave it for two or three hours. After two or three
hours, the DVD video player will have warmed up and
evaporated any moisture. Keep the DVD video player
connected to the wall outlet and moisture
To obtain a clear picture
condensation will seldom occur.
The DVD video player is a high technology, precision
device. If the optical pick-up lens and disc drive parts
are dirty or worn down, the picture quality becomes
poor. To obtain a clear picture, we recommend regular
inspection and maintenance (cleaning or parts
replacement) every 1,000 hours of use depending on
the operating environment. For details, contact your
8nearest dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on Discs
On handling discs
Structure of disc contents
Do not touch the playback side of the disc.
Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. VIDEO CDs and
audio CDs are divided into tracks.
DVD video disc
DVD video disc
Title 1
Title 2
Chapter 1 Chapter 2
Chapter 1 Chapter 2 Chapter 3
Playback side
Do not attach paper or tape to discs.
VIDEO CD/audio CD
VIDEO CD/audio CD
Track 1
Track 2
Track 3
Track 4
Track 5
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.
Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.
Notes on copyright
The unauthorized recording, use, distribution, or
revision of copyrighted materials including, without
limitation, television programs, videotapes, and DVDs, is
prohibited under the Copyright Laws of the United
States and other countries, and may subject you to civil
and criminal liability.
If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Notes on Discs (continued)
About this owner’s manual
Playable discs
This owner’s manual explains the basic instructions of
this DVD video player. Some DVD video discs are
produced in a manner that allows specific or limited
operation during playback. As such, the DVD video
player may not respond to all operating commands. This
is not a defect in the DVD video player. Refer to
instruction notes of discs.
This DVD video player can play the following discs.
Maximum
playback time
Disc
Size
Disc Mark
Contents
Approx. 4 hours
(single sided disc)
12 cm
Audio
+
video
(moving
pictures)
Approx. 8 hours
(double sided disc)
“
” may appear on the TV screen during operation.
” means that the operation is not permitted by the
DVD
video
discs
A “
Approx. 80 minutes
(single sided disc)
DVD video player or the disc.
8 cm
Approx. 160 minutes
(double sided disc)
Notes on region numbers
The region number of this DVD video player is 1. If
region numbers, which stand for their playable area, are
Approx. 74 minutes
Approx. 20 minutes
12 cm
Audio
+
video
(moving
pictures)
printed on your DVD video disc and you do not find
VIDEO
CDs
or
, disc playback will not be allowed by the player.
DIGITAL VIDEO
(In this case, the DVD video player will display a
message on-screen.)
8 cm
Some DVDs that have no region code label may still be
subject to area restrictions and therefore not playable.
Approx. 74 minutes
Approx. 20 minutes
12 cm
Audio
CDs
Audio
8 cm
(CD
single)
On VIDEO CDs
This DVD video player supports VIDEO CDs equipped
with the PBC (Version 2.0) function. (PBC is the
abbreviation of Playback Control.) You can enjoy two
playback variations depending on types of discs.
The following discs are also available.
DVD-R discs of DVD video format
CD-R/CD-RW discs of CD-DA, Video CD, MP3, WMA
or JPEG format
Some of these discs may be incompatible.
• VIDEO CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this DVD video
player in the same way as an audio CD.
• VIDEO CD equipped with PBC function
(Version 2.0)
In addition to operation of a VIDEO CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.
• You cannot play discs other than those listed above.
• You cannot play DVD-RAM discs or
non-standardized discs, etc., even if they may be
labeled as above.
• This DVD video player uses the NTSC color system,
and cannot play DVD video discs recorded in any
other color system (PAL, SECAM, etc.).
Because of problems and errors that can occur during
the creation of DVD software and/or the manufacture of
DVD discs, Toshiba cannot guarantee that this player will
play every feature of every DVD bearing the DVD logo.
As one of the creators of DVD technology, Toshiba DVD
players are manufactured using the highest standards of
quality, and as a result, such incompatibilies are rare. If
you happen to experience any difficulty playing a DVD
on a Toshiba DVD player, please feel free to call our Call
Centre (see page 63 ).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction
Advanced playback
SAFETY PRECAUTIONS .......................... 2
IMPORTANT SAFETY INSTRUCTIONS ... 4
Precautions .............................................. 8
Notes on Discs ......................................... 9
Notes on region numbers ............................... 10
Accessing a Specific Location Directly ... 32
Entering the time counter of the desired
location......................................................... 32
Repeating a Specific Segment .............. 33
Repeating a specific segment ........................ 33
Playing in a Varied Order ....................... 34
Playing titles, chapters or tracks in a varied
order ............................................................. 34
Table of Contents ................................... 11
Identification of Controls....................... 12
Front panel ..................................................... 12
Rear panel...................................................... 12
Remote control ............................................... 13
Loading batteries ........................................... 14
Operating with the remote control .................. 14
Playing in a Favorite Order .................... 35
Setting titles, chapters, or tracks in a favorite
order ............................................................. 35
Zooming a Picture.................................. 36
Zooming a picture .......................................... 36
Selecting the Picture Enhancement
(E.P.M.) .................................................... 37
Selecting the picture enhancement................ 37
Connections
Connecting to aTV................................. 16
Connecting to a TV......................................... 16
Connecting to an audio system and TV
equipped with component video inputs ....... 17
Selecting the Sound Enhancement
(E.A.M.) ................................................... 38
Selecting the sound enhancement................. 38
Connecting to Optional Equipment ...... 18
Connecting to an amplifier equipped with a
Dolby Digital decoder ................................... 19
Selecting the Camera Angle.................. 39
Changing the camera angle ........................... 39
Connecting to an amplifier equipped with
Dolby Surround Pro Logic ............................ 19
Selecting Subtitles ................................. 40
Selecting a subtitle language ......................... 40
Connecting to an amplifier equipped with a
DTS decoder ................................................ 19
Connecting to an amplifier equipped with an
MPEG2 audio decoder................................. 20
Connecting to an amplifier equipped with a
digital audio input ......................................... 21
Selecting a Language ............................ 41
Selecting a playback audio setting................. 41
On-screen Display Operation................ 42
On-screen display operation .......................... 42
Playing MP3/WMA Files ......................... 44
Playing MP3/WMA files .................................. 44
Basic playback
Playing a Disc......................................... 24
Viewing JPEG Files ................................ 46
Viewing JPEG files ......................................... 46
Viewing a thumbnail view ............................... 47
Basic playback ............................................... 24
Variable Speed Playback ....................... 26
Playing in fast reverse or fast forward
directions...................................................... 26
Playing frame by frame .................................. 26
Playing in slow-motion ................................... 27
Resuming playback from the same location .. 27
Function setup
Customizing the Function Settings ...... 50
Setting procedure ........................................... 50
Setting details................................................. 52
Table of Languages................................ 57
Locating a Desired Section ................... 28
Locating a title using the top menu ................ 28
Locating a desired section by entering the
Others
Before Calling Service Personnel ......... 60
Specifications......................................... 61
United StatesWarranty .......................... 62
Canadian Warranty ................................ 64
corresponding number ................................. 29
Locating a specific chapter or track ............... 29
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Identification of Controls
See the page in
for details.
Front panel
24
24
24
24
29
24
25
14
25
Rear panel
16
17
19 20 21
16 17
16
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification of Controls (continued)
The instructions in this manual describe the functions on the remote control. See the page in
for details.
Remote control
24
24
24
43
42
36
41
39
28
40
28
50
28
29
25 26
24
25
29
29
26
27
37
26
17
38
29
29
33
50
35
34
* MENU button
Use the MENU button to display the menu included on
many DVD video discs. To operate a menu, follow the
instructions in “Locating a title using the top menu.”
28
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Loading batteries
Operating with the remote control
Open the cover.
Point the remote control at the remote
sensor and press the buttons.
1
Insert batteries (AAA size).
2
Distance: About 7 m (23 feet) from the front of the
remote sensor
Angle:
About 30° in each direction of the front of
the remote sensor
* Do not expose the remote sensor of the DVD video
player to a strong light source such as direct
sunlight or other illumination. If you do so, you may
not be able to operate the DVD video player via the
remote control.
Make sure to match the + and – on the batteries
to the marks inside the battery compartment.
Notes on the remote control
• Direct the remote control at the remote sensor of the DVD
video player.
• When using the remote control, press the buttons at
intervals of about 1 second to ensure the correct mode of
operation.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot or
humid place.
• Do not spill water or put anything wet on the remote
control.
Caution
• Never throw batteries into fire.
Notes
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Attention should be drawn to the environmental aspects
of battery disposal.
• Do not mix different battery types or combine used
batteries with new ones.
• Do not open the remote control.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace both batteries
with new ones.
• If the batteries are dead or if you will not be using the
remote control for a long time, remove the batteries to
prevent battery acid from leaking into the battery
compartment.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Read this chapter first to make all necessary
preparations.
Connecting to aTV
Connecting to an audio system
andTV equipped with
component video inputs
Connecting to an amplifier
equipped with a Dolby Digital
decoder
Connecting to an amplifier
equipped with Dolby Surround
Pro Logic
Connecting to an amplifier
equipped with a DTS decoder
Connecting to an amplifier
equipped with an MPEG2 audio
decoder
Connecting to an amplifier
equipped with a digital audio
input
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to a TV
Connect the DVD video player to your TV.
For details of output sound, see
.
41
Connecting to a TV
• Make the following setting.
On-screen display
“Digital Output”
Select:
Page
50
“PCM” or
“Bitstream”
55
Composite
* Component
“Video Output”
50 55
* Only for analog video out jack (yellow)
connection with progressive scan off.
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD video player to your TV, be sure to turn off the power and unplug both units from the wall outlet
before making any connections.
• If your television set has one audio input, connect the left and right audio outputs of the DVD video player to a Y cable
adapter (not supplied) and then connect to your TV.
• Connect the DVD video player directly to your TV. If you connect the DVD video player to a VCR, TV/VCR combination or
video selector, the playback picture may be distorted as DVD video discs are copy protected.
• Analog audio out will not have sound if DTS playback is selected.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Interlaced outputs (ColorStream®)
Some TVs or monitors are equipped with component video
inputs. Connecting to these inputs allows you to enjoy
higher quality picture playback.
Actual labels for component video inputs may vary
depending on the TV manufacturer. (ex.Y, R-Y, B-Y or Y,
CB, CR)
In some TVs or monitors, the color levels of the playback
picture may be reduced slightly or the tint may change. In
such a case, adjust the TV or monitor for optimum
performance.
Progressive outputs (ColorStream Pro®)
Some TVs or monitors are equipped with component video
inputs that are capable of reproducing a progressively
scanned video signal. Connecting to these inputs allows
you to view the highest quality pictures with less flicker.
Consumers should note that not all high definition
television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In case
of 525 progressive scan picture problems, it is
recommended that the user switch the connection to the
“standard definition” output. If there are questions
regarding our TV set compatibility with this model 525p
DVD player, please contact our Customer Service Center.
Connecting to an audio system andTV equipped with component video inputs
Switching the output signal (interlaced/progressive)
using the remote control
• Make the following setting.
You can temporarily switch the output signal for better picture
On-screen display
“Digital Output”
Page
Select:
quality.
“PCM” or
“Bitstream”
Press PROGRESSIVE on the remote control during stop mode.
Press PROGRESSIVE again to turn off progressive mode.
50
55
55
50
“Video Output”
Component
Notes
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.
• If you place the DVD video player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the
DVD video player away from the tuner and radio.
• The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, high volume sound may damage your hearing as well as the speakers.
• Turn off the amplifier before you connect or disconnect the DVD video player’s power cord. If you leave the amplifier power
on, the speakers may be damaged.
• Progressive can be on/off only when “Video Output” is set to Component
.
54
• In component connections, the screen might become pinkish in color when the “Video Output” is set to Composite. This is
not a defect of this unit
.
54
• When Progressive is on, only component video will be output.
• Analog audio out will not have sound if DTS playback is selected.
• When using component video cables, do not connect the S video cable.
ColorStream® and ColorStream Pro® are registered trademarks of Toshiba America Consumer Products, L.L.C.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD video player
to optional audio equipment.
• For connection to your TV, see “Connecting to a TV”
Warning
.
16 17
• When you are connecting (via the COAXIAL DIGITAL
AUDIO OUT jack) an AV decoder that does not have
Dolby Digital, Digital Theater Systems (DTS) or MPEG2
decoding function, be sure to set “Digital Output” to
• For details of output sound, see
• This section uses the following reference marks.
.
41
“PCM” from the on-screen displays
high volume sound may damage your hearing as well
as the speakers.
. Otherwise,
50 55
: Front speaker
: Rear speaker
: Sub woofer
• When playing DTS-encoded discs (audio CDs),
excessive noise may be output from the analog audio
output jacks. To avoid possible damage to the audio
system, you should take proper precautions when the
analog audio output jacks of the DVD video player are
connected to an amplification system. To enjoy DTS
Digital Surround™ playback, an external 5.1 channel
DTS Digital Surround™ decoder system must be
connected to the COAXIAL DIGITAL AUDIO OUT jack
of the DVD video player.
: Center speaker
: Signal flow
Notes
• DO NOT connect the COAXIAL DIGITAL AUDIO OUT
jack of the DVD video player to the AC-3 RF input of a
Dolby Digital Receiver. This input on your A/V Receiver is
reserved for Laserdisc use only and is incompatible with
the COAXIAL DIGITAL AUDIO OUT jack of the DVD video
player.
• Connect the COAXIAL DIGITAL AUDIO OUT jack of the
DVD video player to the “DIGITAL (COAXIAL)” input of a
Receiver or Processor.
• Refer to the owner’s manual of the connected equipment
as well.
• When you connect the DVD video player to other
equipment, be sure to turn off the power and unplug all of
the equipment from the wall outlet before making any
connections.
• The output sound of the DVD video player has a wide
dynamic range. Be sure to adjust the receiver’s volume to
a moderate listening level. Otherwise, the speakers may
be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect
the DVD video player’s power cord. If you leave the
amplifier power on, the speakers may be damaged.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to an amplifier equipped with a Dolby Digital decoder
Dolby Digital
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and the
double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished
works. Copyright 1992-1997 Dolby
Laboratories. All rights reserved.
Dolby Digital is the surround sound technology used in theaters showing the
latest movies, and is now available to reproduce this realistic effect in the home.
You can enjoy motion picture and live concert DVD video discs with this dynamic
realistic sound by connecting the DVD video player to a 6 channel amplifier
equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a
Dolby Surround Pro Logic decoder, you will obtain the full benefit of Pro Logic
from the same DVD movies that provide full 5.1-channel Dolby Digital
soundtracks, as well as from titles with the Dolby Surround mark.
• Use DVD video discs encoded via
the Dolby Digital recording
system.
• Make the following setting.
On-screen display
“Digital Output”
Select:
Page
Amplifier equipped with a
Dolby Digital decoder
50
55
“Bitstream” or
“PCM”
To COAXIAL type
digital audio input
To COAXIAL
DIGITAL AUDIO
OUT
Recording system
D
41
75 Ω coaxial cable
Connecting to an amplifier equipped with Dolby Surround Pro Logic
• Make the following setting.
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by
connecting an amplifier and speaker system (right and left front speakers, a
center speaker, and one or two rear speakers).
On-screen display
Select:
Page
“Bitstream” or
“PCM”
50
55
“Digital Output”
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an
amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s
owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro
Logic sound.
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
* Connect one or two rear speakers.
The output sound from the rear speakers
will be monaural even if you connect two
rear speakers.
Amplifier equipped with
Dolby Surround Pro Logic
*
To audio input
To ANALOG
AUDIO OUT
Audio cable
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to Optional Equipment (Continued)
Connecting to an amplifier equipped with a DTS decoder
DigitalTheater Systems (DTS)
DTS is a high quality surround technology used in theaters and now available for
home use, on DVD video discs or audio CDs.
“DTS” and “DTS Digital Out” are
trademarks of Digital Theater Systems,
Inc.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1
channel DTS encoded sound tracks on DVD video discs or audio CDs.
• Use DVD video discs or audio
CDs encoded via the DTS
recording system.
• Make the following setting.
Amplifier equipped with
a DTS decoder
On-screen display
Select:
“Bitstream”
DTS
Page
50
55
“Digital Output”
To COAXIAL type
digital audio input
To COAXIAL
DIGITAL AUDIO
OUT
Recording system
41
75 Ω coaxial cable
Connecting to an amplifier equipped with an MPEG2 audio decoder
• Use DVD video discs encoded via
the MPEG2 recording system.
• Make the following setting.
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs with
dynamic realistic sound by connecting an amplifier equipped with an
MPEG2 audio decoder or MPEG2 audio processor.
On-screen display
“Digital Output”
Select:
Page
50
55
“Bitstream” or
“PCM”
Amplifier equipped with an
MPEG2 audio decoder
Recording system
MPEG2
41
To COAXIAL type
digital audio input
To COAXIAL
DIGITAL AUDIO
OUT
75 Ω coaxial cable
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
• Make the following setting.
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an
amplifier equipped with a digital audio input and speaker system (right and left
front speakers).
On-screen display
Select:
Page
50
“Digital Output”
“PCM”
55
Amplifier equipped with
a digital audio input
To COAXIAL type
To COAXIAL
digital audio input
DIGITAL AUDIO
OUT
75 Ω coaxial cable
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
Begin your operation.
Playing a Disc
Variable Speed Playback
Locating a Desired Section
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
Playing a Disc
This section shows you the basics on how to play a disc.
Basic playback
Preparations
• When you want to view a disc, turn on the TV and select the video input connected to the DVD video player.
• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected
to the DVD video player.
Press the ON/STANDBY button.
Press OPEN/CLOSE to close the disc
tray.
4
1
The DVD video player turns on.
The ON/STANDBY indicator on the
player illuminates.
Playback starts.
If you insert a DVD video disc that contains a
Press OPEN/CLOSE.
top menu, a menu may appear. Use the
to select the title you want to view, then
press ENTER to start playback. See “Locating a
title using the top menu.”
/
/
/
2
3
The disc tray opens.
28
• You may need to press the TOP MENU or MENU
button to display disc menu (depending on the
actual DVD video disc.)
Place the disc on the disc tray.
Notes
• If the disc tray is holding a disc you have already played,
playback will begin from the location where you last
With the playback
side down
stopped. For resuming playback, see
.
27
• Some video CD are recorded with PBC (Playback
Control), a menu with recorded contents may appear on
the TV if you have turned the PBC on.You can make your
selection according to its PBC menu. Press the PBC button
on the remote control to turn PBC on or off anytime during
Video CD playback. When switching from PBC off to PBC
on mode, playback will start from the beginning of the disc.
• There are two different disc sizes. Place the disc in
the correct guide on the disc tray. If the disc is out of
the guide, it may damage the disc and cause the
DVD video player to malfunction.
To start playback in the stop mode
Press PLAY.
• Do not place a disc which is unplayable in this DVD
video player.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
2, 4
1
To obtain a higher quality picture
Occasionally, some picture noise not usually visible during a normal broadcast
may appear on the TV screen while playing a DVD video disc because the high
resolution pictures on these discs include a lot of information. While the amount of
noise depends on the TV you use with this DVD video player, you should generally
reduce the sharpness adjustment on your TV when viewing DVD video discs.
TOP MENU
MENU
About
ENTER
STOP
The
icons on the heading bar show the playable discs for the
function described under that heading.
:You can use this function with DVD video discs.
:You can use this function with VIDEO CDs.
:You can use this function with audio CDs.
DVD
PLAY
PAUSE
CD
To pause playback (still mode)
To turn the power off (To enter the standby
mode)
Press PAUSE/STEP during playback.
Press ON/STANDBY to turn the ON/STANDBY indicator
off.
To resume normal playback, press
the PLAY button.
• The sound is muted during still
mode.
Note
Be aware that this equipment is still powered even after the
ON/STANDBY indicator turns off (standby mode) by pressing
the ON/STANDBY button. To disconnect this equipment
completely from the main power, pull out the power plug from
the wall outlet.
To stop playback
Press STOP.
About the screen saver
When you leave the unit in DVD stop mode for
approximately 2 minutes, the screen saver of the DVD
video player automatically appears. To turn off the
screen saver, press the PLAY button.
To remove the disc
Press OPEN/CLOSE.
Remove the disc after the disc tray
opens completely.
Automatic Power Off function
If the DVD video player is stopped, or the screen saver
is engaged for approximately 20 minutes, the DVD
video player will automatically turn itself off.
Be sure to press the OPEN/CLOSE button to close
the disc tray after you remove the disc.
Notes
• Do not move the DVD video player during playback. Doing so may damage the disc.
• Use the OPEN/CLOSE button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may
cause the DVD video player to malfunction.
• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD video
player to malfunction.
• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the
STOP button on your remote control once the movie is completed.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
Variable Speed Playback
You can play discs at various speeds, and resume playback from the location
where you stopped playback.
STOP
PAUSE
PLAY
REV
FWD
SLOW
Playing in fast reverse or fast forward directions
To resume normal playback
Press PLAY.
Press REV or FWD during playback.
REV: Fast reverse playback
FWD: Fast forward playback
Notes
Each time you press the REV or
FWD button, the playback speed
changes.
• The DVD video player mutes sound and subtitles during
reverse and forward scan of DVD video discs.
• The playback speed may differ depending on the disc.
Playing frame by frame
To resume normal playback
Press PLAY.
Press PAUSE/STEP during still playback.
Each time you press the PAUSE/
STEP button, the picture advances
one frame.
Note
The sound is muted during frame by frame playback.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing in slow-motion
To resume normal playback
Press PLAY.
Press SLOW during playback.
Each time you press the SLOW
button, the slow-motion speed
changes in the following sequence:
4
8
Notes
• The sound is muted during slow-motion playback.
• 3 speeds are available.
Resuming playback from the same location
To start playback from the beginning regardless
of the location where you stopped playback
1 Press STOP twice.
Press STOP at the location where you
want to interrupt playback.
1
2
The DVD video player memorizes
the location where playback is
stopped.
The DVD video player deletes the
memory of the location.
2 Press PLAY.
Press PLAY.
DVD
Playback starts from the
beginning of the current title.
The DVD video player resumes
playback from the location where
you stopped playback.
Playback starts from the
beginning of the disc.
• If you want to return to the beginning of a DVD video
disc, open and close the disc tray once with the
OPEN/CLOSE button before pressing the PLAY
button.
Notes
• Resuming cannot function when:
–you play a PBC-featured VIDEO CD while “PBC” is set to
“On”.
–you open the disc tray.
–you disconnect the power plug of the DVD video player.
• There may be a difference in the location where playback
resumes depending on the disc.
• Settings you changed using the on-screen displays while
the DVD video player keeps a location in the memory may
function only after the memory is cleared.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
Locating a Desired Section
TOP MENU
ENTER
Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs are
divided into tracks. You can quickly locate any specific title, chapter, or track.
DVD video disc
Title 1
Title 2
VIDEO CD/audio CD
Chapter 1 Chapter 2
Chapter 1 Chapter 2 Chapter 3
Track 1
Track 2
Track 3
Track 4
Track 5
DVD
Locating a title using the top menu
PressTOP MENU.
Press ENTER.
1
3
The top menu appears on the TV
screen.
Playback starts from chapter 1 of
the selected title.
e.g.
Notes
• The instructions above describe basic procedures which
may vary depending on the contents of the DVD video disc.
If different instructions appear on the TV screen, follow
those instructions.
• If you display the top menu during playback and press the
TOP MENU button again without selecting any title, the DVD
video player may resume playback from the point where you
first pressed the TOP MENU button (depending on the
actual DVD video disc.)
Press
want.
/
/
/
to select the title you
2
If the titles in the top menu are
assigned a number, you can directly
locate a specific title by pressing its
designated number with the number
buttons.
• This method of locating a title is available only on a disc that
contains a top menu.
• Instruction notes of discs may refer to the button that
displays the top menu as TITLE button.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEAR
ENTER
PLAY
SKIP
T
Number buttons
Locating a desired section by entering the corresponding number
PressT.
Press the number buttons to enter title,
chapter or track number.
1Press
3
4
/
to highlight theTitle/Chapter
orTrack.
If you are using a VIDEO CD/audio CD, skip step 2.
Then at step 3, enter the number for the track you
want using the number buttons.
e.g.
Search
Time
DVD
Press ENTER.
Title/Chapter
Playback starts from the selected
section.
Search
Time
Track
Accessing chapters/tracks using number
buttons:
Press
/
to select a section you want
2to locate.
You can play any chapter/track you want by pressing
the corresponding number button. For the chapters/
tracks number greater than “9”, use “+10” button.
Each press increases the number by 10. Then key in
the second digit of chapter/track number.
e.g. When you want to locate a chapter.
DVD
Notes
• Pressing the CLEAR button resets the numbers. To clear the
display, press the T button several times.
• This method of locating a title is available only on a disc that
contains title numbers.
Locating a specific chapter or track
Notes
Press SKIP
or
repeatedly to access
• Some titles may not display chapter numbers.
• If you press and hold the SKIP
or
button on the
the chapter or track number you want.
front panel during playback, the DVD video player performs
fast reverse or fast forward playback. You can vary the
speed by pressing the button repeatedly.
To locate chapters or tracks during fast reverse or fast
forward playback, first press the PLAY button to resume
Playback starts from the selected chapter or track.
To locate succeeding chapters or
tracks.
normal playback, then use the SKIP
or
button.
Playback starts from the beginning of
the current chapter or track.
When you press twice in quick
successions, playback starts from the
beginning of the preceding chapter or
track.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Customizing the performance of your DVD video player.
Accessing a Specific Location
Directly
Repeating a Specific Segment
Playing in a Varied Order
Playing in a Favorite Order
Zooming a Picture
Selecting the Picture Enhancement
(E.P.M.)
Selecting the Sound Enhancement
(E.A.M.)
Selecting the Camera Angle
Selecting Subtitles
Selecting a Language
On-screen Display Operation
Playing MP3/WMA Files
Viewing JPEG Files
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
CLEAR
Accessing a Specific Location Directly
The unit stores the points that you want to watch again up to 3 points.
You can resume playback from each scene.
ENTER
PLAY
T
Entering the time counter of the desired location
To set and play favorite bookmark during
playback
1. Press T twice, the display of Bookmark appears, then
press ENTER to mark the desired scene.
PressT.
1
2
Press
time counter.
/
button to highlight the
DVD
Track
Press the number buttons to enter the
time.
2. Press ENTER to play the favorite bookmark.
To set other bookmarks.
Follow step 1 and move through the menu by pressing
the or button.
e.g.
Press T again to remove this display.
• The first number you entered represents hours.
• The second two numbers you entered represent
minutes.
• The third two numbers you entered represent
seconds.
• If you input a wrong number, press CLEAR.
To cancel the Bookmark
Follow step 1, then press CLEAR to cancel the
bookmark. Move through the menu by pressing the or
button to cancel other bookmarks.
Press ENTER.
3
Playback starts from the
desired location.
Notes
Notes
• Some discs may not work with marking operation.
• The marking is cancelled when you open the disc tray or
turn the power off.
• Some subtitles recorded around the marker may fail to
appear.
• Some discs may not respond to this process.
• Some scenes may not be located precisely as you
specified.
• This method for accessing specific locations is available
only within the current title of the DVD video disc or within
the current track of the VIDEO CD / audio CD.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeating a Specific Segment
You can specify a desired segment and repeat it.
A-B RPT
Repeating a specific segment
To resume normal playback
Press A-B RPT until Rep off is displayed.
Press A-B RPT at the beginning of the
segment (point A) you want to play
1
repeatedly.
Notes
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a segment that
includes multiple camera angles
.
39
• You can specify a segment only within the current title or
track (VIDEO CD).
• There may be a slight difference between point A and the
location where playback actually resumes depending on the
disc.
Press A-B RPT again at the end of the
segment (point B).
2
The DVD video player automatically
returns to point A and starts repeat
playback of the selected segment
(A-B).
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
ENTER
Playing in a Varied Order
You can play titles, chapters within a title, or tracks in a varied order.
2
1
Playing titles, chapters or tracks in a varied order
Press PLAY.
Press PLAY MODE.
2
1
Press the PLAY button, the DVD
video player starts playback in the
selected mode.
Press
/
button to select desired
features and then press ENTER
button to toggle desired mode.
e.g.
Play mode
Random
Repeat
Off
Off
To resume normal playback
Press ENTER until the Off is displayed.
Off
On
Note
Some discs may not permit these operations.
Off
Chapter
Title
Off
Track
All
Chapter:
Repeats the chapters within the current title.
Title:
Repeats the current title.
Track:
Repeats the current track.
All:
Repeats the entire disc.
Off:
Resumes normal playback.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEAR
Playing in a Favorite Order
You can combine your favorite titles, chapters, or tracks and play them in the
order you determine. You can program up to 12 selections into the memory.
(Memory playback)
3
2
1
Setting titles, chapters, or tracks in a favorite order
To change the programmed selections
1 While the display appears on the TV screen, press
Insert a disc and press MEMORY during
stop.
1
/
/
/
to move the highlighted bar to the item
you want to change.
2 Change the selection following the instructions in
step 2.
The following display appears.
e.g.
Memory
To cancel the programmed selections
1 While the display appears on the TV screen, press
/
/
/
to move the highlighted bar to the item
Memory
you want to cancel.
2 Press CLEAR.
To resume normal playback from memory
playback
Memory
Press MEMORY button.
Press
/
/
/
to move the highlighted bar to Clear
All, then press the ENTER. All the input programs will
be cleared.
Press PLAY button to resume normal playback.
Memory
Normal playback will start from first
location.
Select the items in the order you want
by pressing the number buttons.
To program during playback
If you press the MEMORY button during playback, a
programming display appears.
2
3
Each time you press the
/
/
/
button, the
space is highlighted in turn. Highlight where you
want to enter, then press the corresponding
number buttons.
Follow steps 2 and 3.
Notes
• Some discs may not permit memory playback operation.
• If you select repeat during memory playback, the DVD
To select another chapter in the same title, you do
not need to select the title number.
34
To select tracks from a VIDEO CD/audio CD in
order, press the number buttons for the track.
video player repeats the current memory playback.
• If you press the MEMORY or RETURN button while the
display appears on the TV screen, the display disappears.
• The programmed selections will be cleared when you turn
off the DVD video player.
Press
/
/
/
to move the highlighted
bar to Play Memory, then press the
ENTER.
The DVD video player starts
memory playback.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Zooming a Picture
ZOOM
You can magnify areas within a picture.
Zooming a picture
To resume normal playback
Press ZOOM repeatedly until the Off is displayed.
Original picture is restored.
Press ZOOM during normal, slow or still
playback.
The centre part of the image will be
zoomed in.
e.g.
2
Notes
• Some discs may not respond to zoom feature.
• During some scenes, the buttons may not work as
described.
• Zooming does not work on subtitles or menus included on
DVD video discs.
• The magnification level varies depending on the picture size
Each time you press the ZOOM
button, the magnification level
changes as follows:
you select.
54
1
2
3
Off
Press the ZOOM button to select the
magnificant level.
Press the
/
/
/
buttons to
view a different part of the image.
You may move the image from the
centre position to UP, DOWN, LEFT
and RIGHT direction.
When you reach the edge of the
image, the display will not shift
anymore in that direction.
Off
Press the ZOOM button repeatedly
until the
is displayed.
Off
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Picture Enhancement (E.P.M.*)
You can easily select a preferred picture enhancement.
*E.P.M.: Enhanced Picture Mode
2
E.P.M.
Selecting the picture enhancement
To exit the picture enhancement selection
Press E.P.M. again.
Press E.P.M.
1
2
The picture enhancement menu
appears.
Note
Actual effect to picture may vary depending on the TV. Make
selection according to your preference.
Select the picture enhancement by
pressing / , then press
your selections.
/
to make
Each time you press the
enhancement changes.
/
button, the picture
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Selecting the Sound Enhancement (E.A.M.*)
You can easily switch a preferred audio enhancement.
*E.A.M.: Enhanced Audio Mode
E.A.M.
Selecting the sound enhancement
To exit the audio enhancement selection
Press E.A.M.
1
Leave the DVD video player unattended for about 5
seconds after having made a selection.
The sound enhancement will
appear:
Notes
3D On
• Actual effects to sounds may vary depending on the
speaker system. Make selection according to your
preference.
• Actual effects to sounds may vary depending on the disc.
• When the DVD video player is connected to an amplifier
equipped with Dolby Surround Pro Logic, select “3D off”.
Otherwise, Dolby Surround Pro Logic may function
differently than usual.
Press the E.A.M. button again, the sound
enhancement change to OFF.
3D*:
To obtain expansive virtual surround sound effects
from two speakers.
To use this enhancement on sounds output from
the ANALOG AUDIO OUT jacks, be sure to set
“Digital Output” to “PCM”.
* Effective in playback of a DVD video disc or a
VIDEO CD.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Camera Angle
If the scene was recorded from multiple angles, you can easily change
the camera angle of the scene you are watching.
ANGLE
DVD
Changing the camera angle
To resume normal playback
Press the ANGLE repeatedly until the “
displayed.
Press ANGLE while playing a scene
recorded with multiple angles.
” is
1/3
1
While playing a scene recorded with
multiple angles, press the ANGLE
button.
Notes:
• This function can only be used for discs on which
scenes shot from multiple angles have been recorded.
e.g.
• If only one angle is recorded, “
” is displayed.
1/1
Number changes to show the
number of the current angle. (The
maximum number of possible angles
is 9)
Press ANGLE while the angle number is
displayed on theTV screen.
2
Press the ANGLE button repeatedly
to change the scene to the next
angle in those recorded.
• About two seconds later, playback
continues from the new angle you
selected.
• If no button is pressed within 10
seconds, playback continues
without changing the current
angle.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Selecting Subtitles
You can display subtitles on the TV screen and select a subtitle language
from those included on the DVD video disc.
SUBTITLE
DVD
Selecting a subtitle language
To turn subtitles on or off
1 Press SUBTITLE during playback.
Press SUBTITLE during playback.
1
2
The current subtitle setting is
displayed.
e.g.
2 Press SUBTITLE repeatedly until the
displayed.
is
Notes
• Some DVD video discs are set to display subtitles
automatically, and you cannot turn them off even if you set
the subtitle function to off.
• During some scenes, the subtitles may not appear
immediately after you select your desired.
• Some DVD video discs will allow you to make subtitle
selections and turn subtitles on or off only via the disc
menu.
Press SUBTITLE while the subtitle setting
is displayed on the TV screen.
Each time you press the SUBTITLE
button, the subtitle languages
included on the DVD video disc
change.
e.g.
To turn off the subtitle setting
display, press the SUBTITLE button
repeatedly until
is displayed.
Notes
• When you turn on the DVD video player or replace a disc, the player returns to the initial default setting
.
56
When you select a subtitle language which is not included on the disc, the DVD video player plays a prior language
programmed on the disc.
• During some scenes, the subtitles may not appear immediately after you change the subtitle language.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Language
You can select a preferred language and sound recording system from those
included on the DVD video disc.
AUDIO
Selecting a playback audio setting
Press AUDIO during playback.
Press AUDIO while the audio setting is
displayed on theTV screen.
1
2
The current audio setting is
displayed.
Each time you press the AUDIO
button, the audio settings included
on the DVD video disc change.
e.g.
To turn off the audio setting display, press the
AUDIO button.
Notes
• When you turn on the DVD video player or replace a disc,
player returns to the initial default setting .
If you select a sound track which is not included on the disc,
the DVD video player plays a prior sound track programmed
on the disc.
Recorded audio format number
changes sequentially. (The
maximum number of possible audio
formats is 8)
• Some discs allow you to change audio selections only via
the disc menu. If this is the case, press the MENU button
and choose the appropriate language from the selections on
the disc menu.
The abbreviation of the language appears instead
of the language name. Refer to the list of
languages and their abbreviations.
57
Selecting sound channels of VIDEO CDs
Press AUDIO repeatedly during
playback to hear a different audio
channel (stereo, Left or Right).
Output sound conversion table
• Signals of 96kHz from the
COAXIAL DIGITAL AUDIO OUT
Digital Output
50 55
jack are depressed to 48 kHz by
down sampling process when:
– “3D On” is selected.
38
– a copyright protected disc is
played.
• Quantization bit of signals of 20 bit
or higher which is output from the
COAXIAL DIGITAL AUDIO OUT
jack is 16 bit if they are in a
copyright protected disc.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
On-screen Display Operation
NAVI
When you turn on the on-screen display, you can view information on
operational status and access features and settings.
ENTER
On-screen display operation
Press NAVI.
The following display appears.
See the pages in
for details on the features.
e.g. When playing a DVD video disc
1/3 1/16 00:02:30
Title number
Chapter number
Elapsed time
Features
:
To stop playback.
25
Title number (Track number)
Locate a title or track using the number
buttons.
:
Playback starts from the beginning of the
current chapter or track.
29
29
Chapter number
Locate a chapter using the number buttons.
29
:
To start playback.
24
Elapsed time of the current title or track
To enter the time to locate a desired
:
To locate succeeding chapters or tracks.
location.
32
29
:
To pause playback.
25
42
Download from Www.Somanuals.com. All Manuals Search And Download.
On-screen Display Operation (Continued)
DISPLAY
On-screen display operation
Viewing the operational status
1 Press DISPLAY.
The following display appears.
Time counter
DVD
Elapsed time / remaining time of the current title
VCD
CD
Elapsed time / remaining time of the current track
29
Chapter number
29
39
Title number
Angle Setting
Audio Setting
40
Subtitle Setting
Off
5.888Mbps
41
Bitrate
Bit Rate
2 To turn off the display, press DISPLAY again.
Bit rate (Mbit/s)
Amount of picture, sound and subtitle data in
the DVD video disc transferred per second.
The larger the value is, the more data
processed, but this does not necessarily insure
better picture quality.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
2
Playing MP3/WMA Files
You can play MP3/WMA files that have been recorded on a CD-R or CD-ROM
on the DVD video player.
ENTER
PLAY
PAUSE/STEP
3
T
Playing MP3/WMA files
Preparations
• Make sure that a disc you want to play is compatible with this DVD video player.
45
Selecting a track (file) in the disc
Place a CD that contains MP3/WMA files
on the disc tray.
1 Press T.
1
2
2 Enter the track number to select a track you want
to play.
3 Press ENTER to begin playback of the selected
track.
The current track being played is highlighted in
green.
Press OPEN/CLOSE to load the disc.
Playback starts.
Notes
• Letters of a file/folder name overflowing the given space
are not displayed.
• You can not play in Fast reverse or Fast forward during
MP3/WMA playback.
To stop playback, press STOP.
3
To pause playback
Press PAUSE/STEP during playback.
To resume normal playback, press
the PLAY button.
Notes
• Some discs may not permit this operation.
• WMA tracks copy-protected cannot be played.
• The COAXIAL DIGITAL AUDIO OUT jack outputs MP3/WMA sounds in the linear PCM format regardless of the current
“Digital Output” selection
.
55
41
• If you stop playback by pressing the STOP button twice and then press the PLAY button, playback will start from the first
track of the disc.
• The SKIP
and PLAY MODE
functions are also available.
34
29
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Playable files
MP3/WMA disc compatibility with this player is limited as follows:
• Playable discs:
CD-ROM, CD-R (650MB / 74 min. only)
CD-RW is not recommendable.
44.1 kHz only
WMA: 48 kbps - 192 kbps (CBR*)
MP3: 32 kbps - 320 kbps (CBR*)
Mode 1, Mode 2 XA Form 1
• Sampling Frequency:
• Bit rate:
• CD physical format:
• File system:
ISO9660 Level 1, 2 or Joliet
• File name:
A file name should be in alphabet and numerals only, and must incorporate “MP3” or
“WMA” extension.
e.g.“********.MP3”, “********.WMA”
Less than 256
Less than 1000
• Total number of folders:
• Total number of files:
• WMA codec version:
V7 or V8 (Stereo sound only)
* CBR = Constant Bit Rate
This DVD video player requires discs/recordings to
meet certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are
automatically set to these standards. There are many
different types of recordable disc formats (including CD-
R containing MP3/WMA files). Because this area of
technology is still evolving, Toshiba cannot guarantee
that all recordable discs will produce optimal playback
quality. The technical criteria set forth in this owner’s
manual are meant only as a guide.
Please be advised that you must obtain permission
from the applicable copyright owners to download
copyrighted content, including music files, in any
format, including the MP3 and WMA formats, prior to
the downloading thereof. Toshiba has no right to grant
and does not grant permission to download any
copyrighted content.
Microsoft, Windows Media, and the Windows
Logo are trademarks or registered trademarks
of Microsoft Corporation in both the United
States and other countries.
Note
When the WMA or MP3 file is out of the above specifications,
the song may be skipped or muted with counter moving.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Viewing JPEG Files
You can play JPEG files that have been recorded on a CD-R or
CD-ROM on the DVD video player.
TOP MENU
You can select a preferred view: a page of 9 thumbnail images or
a single image view.
Also, rotating, enlarging and shifting of each image can be
possible.
ENTER
PLAY
PAUSE/STEP
STOP
Viewing JPEG files
Preparations
• Prepare a disc that contains JPEG files you want to view.
48
• Make your TV shape conform to the 4:3 picture size. Only 4:3 pictures can be played regardless of the function
settings via the on-screen displays of the DVD video player. If the TV is adjusted to other sizes, e.g. “WIDE,”
images will appear to be horizontally expanded. For details, refer to the owner’s manual of your TV.
To quit the JPEG playback, press STOP.
Press OPEN/CLOSE to open the disc
• Pressing the OPEN/CLOSE button to
open the disc tray can also quit the
playback.
tray, place a disc that contains JPEG
1
files.
Press OPEN/CLOSE to close the
disc tray, after completion of reading,
playback automatically starts. The
next picture will automatically display
after a few seconds.
To pause playback
Press PAUSE/STEP during playback
To resume normal playback, press
A view appears.
(Automatic mode)
e.g.
PLAY.
To change the image
To view the succeeding image, press
SKIP
.
To view the previous image, press SKIP
.
A list of folders in
the disc appears.
(Selection mode)
e.g.
To magnify image
Flower
Press ZOOM repeatedly.
Each time you press the ZOOM button, the
magnification level changes as follows:
0001
0002
0006
0007
0003
0004
0008
0009
1
2
3
Off
Press the
/
/
/
buttons to view a different part of
0005
0010
the image.You may move the image from the centre
position to UP, DOWN, LEFT and RIGHT direction. When
you reach the edge of the image, the display will not shift
anymore in that direction.
Press
/
/
/
to select your
desired file, and then press ENTER
or PLAY button to start playback.
Press STOP to display a folder list.
To rotate an image
Press the ANGLE repeatedly
Press SEARCH and enter the track
number followed by ENTER button to
quickly select your image.
The image rotates by clockwise 90-
degree.
Search
Track
To resume normal playback
Press the ZOOM repeatedly until the
• Original picture is restored when the
appears.
is displayed.
Off
Off
• Depending on the file size, some files
may not display the entire image.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing a thumbnail view
To quit the JPEG playback, press STOP.
• Pressing the OPEN/CLOSE button
PressTOP MENU in full-screen review.
to open the disc tray can also quit
the playback.
1
To pause playback
Press PAUSE/STEP during playback
To resume normal playback, press
PLAY.
Prev
Next
To view the
previous 9 images.
To view the
succeeding 9 images.
Press the
/
/
/
to select
an image, press PLAY to view
one image in full-screen and
automatically images will be
displayed one by one again in a
few seconds.
Turn the page if necessary
Press
/
/
/
to highlight the PREV
or
NEXT
screen.
and ENTER to review other thumbnail
Notes
• Depending on the file size, some files may not display the entire image.
• If you press the TOP MENU in full-screen review, the DVD video player will display a menu of 9 thumbnail images.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
JPEG files compatibility
Discs whose compatibility with this DVD video player has been confirmed by TOSHIBA are as follows.
Many of these discs, when loaded, will make the DVD video player enter the automatic mode to play a prescribed
folder in the disc. To play other folders, display a folder list and select a folder.
CANON QuickCD
FUJICOLOR CD
Kodak Picture CD
NORITSU QSS CD
JPEG disc compatibility with this DVD video player is limited as follows:
• Playable discs:
CD-ROM, CD-R (650MB / 74 min. only)
CD-RW is not recommendable.
• CD physical format:
• File system:
Mode 1, Mode 2 XA Form 1
ISO9660 Level 1, 2 or Joliet
• File name:
A file name should be in alphabet and numerals only, and must incorporate “JPG”
extension.
e.g.“********.JPG” (Do not name the file with “JPE” or “JPEG” extension.)
• Total number of folders:
• Total number of files:
Less than 256
Less than 1000
Depending on the file size, some files may not display the entire image.
Some discs may not permit this operation. Especially, the following conditions of included files will increase the disc’s
disability.
1. Pixels over 3072 x 2048 in height and/or width
2. File format except Exif
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
You can change the default settings to customize
performance to your preference.
Customizing the Function
Settings
Table of Languages
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
2
Customizing the Function Settings
RETURN
ENTER
You can change the default settings to customize performance to your
preference.
3, 4
1, 6
Setting procedure
Press SETUP during stop.
Press
/
to select the setting you
want to change, then press ENTER.
1
2
3
4
The following on-screen display
appears.
Change the selection by
by referring to the corresponding
pages, then press ENTER.
/
buttons,
Press
/
to select an option for the
setting you want to change, then press
ENTER.
(See the next page.)
Repeat steps 3 and 4 to change other
settings.
To select another option, press RETURN to go
5
6
back to step 2.
Press SETUP.
Language settings
Video settings
Audio settings
Rating settings
The on-screen display disappears.
To return to the previous display
Press RETURN.
Note
To quit the procedure, press the SETUP button to turn off the
on-screen display.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Details
Page
Language
To select a preferred language for on-screen
display.
52
OSD Menu
Subtitle
Audio
DVD
DVD
To select a preferred language for subtitles.
52
53
To select a preferred language for the sound
track.
DVD Menu
DVD
53
To select a preferred language for disc menus.
Video
To select a picture size according to aspect
ratio of your TV.
54
54
DVD
TV Shape
To select whether you send Composite or
Component signals to the connectedTV.
Video Output
Audio
To select an output sound format corresponding
to your system connection.
55
Digital Output
Rating
DVD
DVD
To create a personal security code.
55
Password
Parental
To turn the parental lock function on or off.
55
56
To return the initial settings such as Language,
Video, Audio and etc. to the factory default.
Default
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
Customizing the Function Settings (continued)
Setting details
DVD
Subtitle
Language
English:
To display subtitles in english.
Deutsch: To display subtitles in german.
Français: To display subtitles in french.
Español: To display subtitles in spanish.
Italiano:
Auto:
To display subtitles in italian.
To display subtitles in different
languages other than you selected.
To disable subtitles.
Off:
OSD Menu
1) Press ENTER.
2) Press to select the Subtitle.
3) Press ENTER button, then the
and change the Language.
4) Press ENTER.
English: To view on-screen displays in english.
Deutsch: To view on-screen displays in german.
Français: To view on-screen displays in french.
Español: To view on-screen displays in spanish.
Italiano: To view on-screen displays in italian.
/
/
to shift
5) Press RETURN.
1) Press ENTER.
2) Press
/
to select the OSD Menu.
3) Press ENTER button, then the
and change the Language.
4) Press ENTER.
/
to shift
5) Press RETURN.
Notes
• Some DVD video discs may be set to display subtitles
in a different language other than you selected. A prior
subtitle language may be programmed on the disc.
• Some DVD video discs allow you to change subtitle
selections only via the disc menu. If this is the case,
press the MENU button and choose the appropriate
subtitle language from the selection on the disc menu.
Note
Some DVD video discs may not include your pre-
selected language. In this case, the DVD video player
automatically displays disc menus consistent with the
disc’s initial language setting.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD
DVD
Audio
DVD Menu
English:
To play sound tracks in english.
English:
To display DVD menus in english.
Deutsch: To play sound tracks in german.
Français: To play sound tracks in french.
Español: To play sound tracks in spanish.
Deutsch: To display DVD menus in german.
Français: To display DVD menus in french.
Español: To display DVD menus in spanish.
Italiano:
To play sound tracks in italian.
Italiano:
To display DVD menus in italian.
1) Press ENTER.
2) Press to select the Audio.
1) Press ENTER.
2) Press to select the DVD menu.
/
/
3) Press ENTER button, then the
and change the Language.
4) Press ENTER.
/
to shift
3) Press ENTER button, then the
and change the Language.
4) Press ENTER.
/
to shift
5) Press RETURN.
5) Press RETURN.
Note
Note
Some DVD video discs may not include your pre-
selected language. In this case, the DVD video player
automatically displays disc menus consistent with the
disc’s initial language setting.
Some DVD video discs may not be played in a different
language than you selected. A prior language may be
programmed on the disc.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
Customizing the Function Settings (continued)
Setting details
Video Output
Video
1) Press
2) Press ENTER.
3) Press to select the Video Output.
/
to select the Video.
/
4) Press ENTER button, then press
the output mode.
/
to select
5) Press ENTER.
6) Press RETURN.
DVD
TV Shape
Component: Corresponding to your TV which has a
component video inputs. Progressive
mode can only be on when Component
is selected.
1) Press
2) Press ENTER.
3) Press ENTER button, then press the
shift and change the TV type
4) Press ENTER.
/
to select the Video.
/
to
Composite: Select if you connect the DVD to TV via
composite video (yellow) input or
S-VIDEO input.
5) Press RETURN.
4:3 Pan Scan:
Select when a standard 4:3 TV is
connected.
Displays pictures cropped to fill
your TV screen. Either or both
sides of the picture are cut off.
Component
Component
Composite
4:3 Letter Box:
Select when a standard 4:3 TV is
connected.
Displays theatrical images with
masking bars above and below the
picture.
Note
At Component mode, there is no S-VIDEO output.
16:9 Wide:
Select when a 16:9 wide TV is
connected.
Notes
• The displayable picture size is preset on the DVD
video disc. Therefore, the playback picture of some
DVD video discs may not conform to the picture size
you select.
• When you play DVD video discs recorded in the 4:3
picture size only, the playback picture always appears
in the 4:3 picture size regardless of the TV shape
setting.
• If you select “16:9 Wide” and you own a 4:3 TV set, the
DVD playback picture will be horizontally distorted
during playback. Images will appear to be horizontally
compressed. Always be sure that your TV shape
conforms to the actual TV in use.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio
Rating
DVD
Digital Output
Password / Parental
Selected the output sound format corresponding to
your system connection.
DVD discs equipped with the password function are
rated according to their content. The contents
allowed by a parental lock level and the way a DVD
disc can be controlled may vary from disc to disc.
1) Press
/
to select Audio.
2) Press ENTER.
3) Press ENTER button, then press
and change the output sound format.
4) Press ENTER.
5) Press RETURN.
For example, if the disc allowed, you could edit out
violent scenes unsuitable for children and replace
them with more suitable scenes, or you could lock
out playback of the disc altogether.
/
to shift
• DVD video discs may or may not respond to the
parental lock settings. This is not a defect in the
DVD video player. Make sure this function works
with your DVD video discs.
PCM: Select when connected to a 2 channel
digital stereo amplifier.
The DVD video player outputs sounds in the
PCM 2 channel format when you play a
DVD video disc recorded on the Dolby
Digital, MPEG1 OR MPEG2 recording
system.
1) Press
2) Press ENTER.
3) Press to select Parental and then press
/
to select the Rating.
/
ENTER repeatedly to set the parental lock
level.
Bitstream: Does not have a Dolby Digital Decode.
4) Press to the Password and enter your 4-
digits security code, then press ENTER button.
5) Press RETURN.
Note
When you make a connection to a TV, or Dolby Surround
Pro Logic or stereo system via the analog audio jacks,
select “PCM” or “Bitstream”.
Password
Parental
Default
- - - -
Password
Parental
Default
- - - -
8. Adult
No
8. Adult
No
Notes
• If you make a mistake before pressing ENTER button,
press CLEAR button and enter your 4-digit security
code again.
• You cannot play DVD discs rated higher than the level
you selected unless you cancel the parental lock
function.
(continued)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
Customizing the Function Settings (continued)
Setting details
(continued)
Default
The parental lock level is equivalent to the following
ratings:
If you want to return the inital language setting such
as Language, Video, Audio and etc. to the factory
default, do the following:
Level 1: Kid Safe
Level 2: G
1) Press
2) Press ENTER.
3) Press to select the Default.
4) Press ENTER.
/
to select Rating.
/
Level 3: PG
Level 4: PG-13
Level 5: PG-R
Level 6: R
5) Press
button.
/
to select Yes, then press ENTER
Level 7: NC-17
Level 8: Adult
Password
Parental
Default
- - - -
8. Adult
No
Indicates Parental lock is not active.
The Parental lock is active.
No
Yes
If you forget the password, you can erase
your current password by pressing number
button 8 on the remote four times, then press
ENTER button to confirm the setting.
Note
When you reset the DVD video player to the factory
default, the DVD video player will take 3-5 seconds to
reset.
PASSWORD: 8888
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Languages
Table of languages and their abbreviations
Abbreviation
Language
Abbreviation
Language
Abbreviation
Language
– – –
No alternate
language
Chinese
Dutch
English
French
German
Italian
Japanese
Korean
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
CHI (ZH)
DUT (NL)
ENG (EN)
FRE (FR)
GER (DE)
ITA (IT)
JPN (JA)
KOR (KO)
MAY (MS)
SPA (ES)
AA
Sango
Malay
Spanish
Afar
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
IW
JI
SK
SL
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Belorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Yiddish
JW
KA
KK
KL
KM
KN
KS
KU
KY
LA
LN
LO
LT
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
LV
MG
MI
MK
ML
MN
MO
MR
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Irish
Scottish Gaelic
Galician
Xhosa
Yoruba
Zulu
GL
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Before Calling Service Personnel
Specifications
United StatesWarranty
Canadian Warranty
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Before Calling Service Personnel
Check the following guide for the possible cause of a problem before contacting service.
Symptoms and correction
Symptom
Cause
Correction
Page
No power.
• The power plug is disconnected.
• Connect the power plug securely into the
wall outlet.
16
The DVD video player turned off • The automatic power off function turned the
• Press the PLAY button.
25
24
by itself.
unit off.
No picture or abnormal color
(pinkish, greenish, etc.).
• The TV is not set to receive DVD signal
output.
• Select the appropriate video input mode on
the TV so the picture from the DVD video
player appears on the TV screen.
• The video cable is not connected securely.
• Connect the video cable securely into the
appropriate jacks.
16,17
• Mismatch setting between TV and this unit.
• Wrong connection.
• Select the correct Video Output setting.
• Check the connection.
54
16,17
No sound.
• The equipment connected with the audio cable • Select the correct input mode of the audio
is not set to receive DVD signal output.
• The audio cable is not connected securely.
• The audio receiver or TV is turned off.
receiver so you can listen to the sound from
the DVD video player.
24
• Connect the audio cable securely into the
appropriate jacks.
16-21
• Turn on the equipment connected with the
audio cable.
24
• The setting of output sound format is
incorrect.
• Select the proper audio setting.
41,50,55
The playback picture has
occasional distortion.
• The disc is dirty.
• Eject the disc and clean it.
9
-
• It is in fast forward or fast reverse playback.
• Sometimes a small amount of picture
distortion may appear.This is not a
malfunction.
Brightness is unstable or noises • The effect of copy protection.
are present in the playback
pictures.
• Connect the DVD video player directly to the
TV. Avoid connecting the DVD video player
to a VCR or TV/VCR combination.
16
The DVD video player does not
start playback.
• No disc is inserted.
• Insert a disc.
24
10
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc type
and color system.)
• The disc is placed upside down.
• Place the disc with the playback side down.
24
24
• The disc is not placed within the guide.
• Place the disc correctly inside the guide on
the disc tray.
• The disc is dirty.
• Clean the disc.
9
• The parental lock function is set.
• Cancel the parental lock function or change
the parental lock level.
50,55
Playback does not follow the
course of the disc’s program.
• It is in the mode of repeat playback, memory
playback, etc.
• These operations may prevent a proper
progress of the contents.
-
-
Buttons do not work.
• Power supply fluctuations or other
abnormalities such as static electricity may
interrupt correct operations.
• Press and hold the ON/STANDBY button on
the front panel for more than about 3
seconds.The DVD video player turns off.
Press the button again to turn it on. If the
buttons still do not work, disconnect the
power plug and insert it into the wall outlet
again.
The remote control does not
work properly.
• The remote control is not pointed at the
remote sensor of the DVD video player.
• Point the remote control at the remote
sensor of the DVD video player.
14
• The remote control is too far from the DVD
video player.
• Operate the remote control within about 7 m.
14
14
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
DVD video player / outputs / supplied accessories
DVD Video Player
Power supply
Power consumption
Mass
120 V AC, 60 Hz
11 W
1.5 kg
External dimensions
Signal system
Laser
430 x 42 x 200 mm (W/H/D)
Standard NTSC
Semiconductor laser, wavelength 650/780 nm
Frequency range
DVD linear sound : 48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
Signal-to-noise ratio
Audio dynamic range
Harmonic distortion
Wow and flutter
More than 100 dB
More than 93 dB
Less than 0.005 %
Below measurable level (less than 0.001 % (W.PEAK))
Temperature: 5 °C to 35 °C, Operation status: Horizontal
Operating conditions
Outputs
Video output
1.0 V (p-p), 75 Ω, negative sync., pin jack x 1
S video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin x 1
(C) 0.286 V (p-p), 75 Ω
Component video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., pin jack x 1
(PB)/(PR) 0.7 V (p-p), 75 Ω, pin jack x 2
Audio output (COAXIAL DIGITAL)
Audio output (ANALOG)
0.5V (p-p), 75 Ω, pin jack x 1
2.0 V (rms), 680 Ω, pin jacks (L, R) x 1
Supplied Accessories
Audio/video cable ..................................................1
Remote control (SE-R0177)....................................1
Batteries (AAA) .......................................................2
•This model complies with the above specifications.
• Designs and specifications are subject to change without notice.
•This model may not be compatible with features and/or specifications that may be added in the future.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Limited United States Warranty
DVD Players - Exchange Warranty
Toshiba America Consumer Products, L.L.C.(“TACP”) makes the following limited warranties to original consumers in the
United States. THESE LIMITED WARRANTIES EXTENDTOTHE ORIGINAL CONSUMER PURCHASER OR ANY
PERSON RECEIVINGTHIS DVD PLAYER AS A GIFT FROMTHE ORIGINAL CONSUMER PURCHASER ANDTO NO
OTHER PURCHASER ORTRANSFEREE.
PRODUCTS PURCHASED INTHE U.S.A.AND USED ANYWHERE OUTSIDE OFTHE U.S.A., INCLUDING, WITHOUT
LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BYTHESEWARRANTIES.
PRODUCTS PURCHASED ANYWHERE OUTSIDE OFTHE U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND
MEXICO, AND USED INTHE U.S.A., ARE NOT COVERED BYTHESE WARRANTIES.
Limited Ninety (90) DayWarranty
Owner’s Manual and Product Registration Card
Read this owner’s manual thoroughly before operating this
DVD Player.Complete and mail the enclosed product
registration card or register your product on-line at
registering your DVD Player you will enableTACP to bring
you new products specifically designed to meet your needs
and help us to contact you in the unlikely event that a safety
notification is required under the Consumer Product Safety
Act.Failure to complete and return the product registration
card does not diminish your warranty rights.
TACP warrants this DVD Player and its parts against
defects in materials or workmanship for period of ninety
(90) days after the date of original retail purchase.
DURINGTHE FIRST NINETY (90) DAYS AFTERTHE
DATE OF ORIGINAL RETAIL PURCHASE,TACPWILL
EXCHANGE A DEFECTIVE DVD PLAYERWITH A NEW
OR REFURBISHED DVD PLAYERWITHOUT CHARGE
TOYOU. YOU MUST CONTACTTACP’S CONSUMER
SOLUTIONS CENTER FOR INSTRUCTIONS ON HOW
TO PROCESSYOUR INWARRANTY EXCHANGE
REQUEST. THE CONSUMER IS RESPONSIBLE FOR
ALL INBOUNDTRANSPORTATION AND INSURANCE
CHARGES FORTHE DVD PLAYERTOTHE
Your Responsibility
THE ABOVEWARRANTIES ARE SUBJECTTOTHE
FOLLOWING CONDITIONS:
EXCHANGE CENTER. DURINGTHE PERIODTHAT
COMMENCES ONTHE DATETHAT IS NINETY ONE
(91) DAYS AFTERTHE DATE OF ORIGINAL RETAIL
PURCHASE AND BEYOND,TACPWILL EXCHANGE A
DEFECTIVE DVD PLAYERWITH A NEW OR
(1) You must retain your bill of sale or provide other proof of
purchase.
REFURBISHED DVD PLAYER FOR A NOMINAL FEE.
YOU MUST CONTACTTACP’S CONSUMER
(2) All warranty servicing of this product must be made by
an AuthorizedTACP Service Station.
SOLUTIONS CENTER FOR INSTRUCTIONS ON HOW
TO PROCESSYOUR EXCHANGE REQUEST. THE
CONSUMER IS RESPONSIBLE FOR ALL INBOUND
TRANSPORTATION AND INSURANCE CHARGES FOR
THE DVD PLAYERTOTHE EXCHANGE CENTER.
(3) The warranties fromTACP are effective only if the
product is purchased and operated in the Continental
U.S.A. or Puerto Rico.
(4) Labor service charges for set installation, setup,
adjustment of customer controls and installation or repair
of antenna systems are not covered by this warranty.
Reception problems caused by inadequate antenna
systems are your responsibility.
Rental Units
The warranty for rental units begins with the first rental or
thirty (30) days after the date of shipment to the rental
firm, whichever comes first.
Commercial Units
(5) Warranties extend only to defects in materials or
workmanship as limited above, and do not extend to any
DVD Player or parts that have been lost or discarded by
you or to damage to the DVD Player or parts caused by
fires, misuse, accident, Acts of God (such as lightning or
fluctuations in electric power), improper installation,
improper maintenance, or use in violation of instructions
furnished byTACP;use or malfunction through
simultaneous use of this product and connected
equipment; or to units that have been modified or had the
serial number removed, altered, defaced, or rendered
illegible.
DVD Players sold and used for commercial purposes
have a limited ninety (90) day warranty for all parts and
labor.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
How to ObtainWarranty Services
THISWARRANTY GIVESYOU SPECIFIC LEGAL RIGHTS
ANDYOU MAY ALSO HAVE OTHER RIGHTSWHICH MAY
VARY FROM STATETO STATE INTHE U.S.A. SOME
STATES OFTHE U.S.A. DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIEDWARRANTY LASTS,WHEN
AN ACTION MAY BE BROUGHT, ORTHE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SOTHE ABOVE PROVISIONS MAY NOT
APPLYTOYOU UNDER SUCH CIRCUMSTANCES.
If, after following all of the operating instructions in this
manual and checking the section “Troubleshooting,”you
found that service is needed:
(1) For instructions on how to obtain warranty service for
exchange program DVD Players, contactTACP’s Call
Center toll free at 1-866-583-7353.
(2) You must include the original bill of sale (or a copy of the
original bill of sale) or other proof of purchase along with
the entire DVD Player when sending the DVD Player to
the AuthorizedTACP Service Station specified byTACP’s
Call Center. You must pay for all transportation and
insurance charges for the DVD Player to and from the
AuthorizedTACP Service Station.
For additional information, visitTACP’s website:
ALLWARRANTIES IMPLIED BYTHE LAW OF ANY
STATE OFTHE U.S.A., INCLUDINGTHE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE EXPRESSLY
LIMITEDTOTHE DURATION OFTHE LIMITED
WARRANTIES SET FORTH ABOVE.WITHTHE
EXCEPTION OF ANYWARRANTIES IMPLIED BYTHE
LAW OF ANY STATE OFTHE U.S.A. AS HEREBY
LIMITED,THE FOREGOINGWARRANTY IS EXCLUSIVE
AND IN LIEU OF ALL OTHERWARRANTIES,
GUARANTEES,AGREEMENTS, AND SIMILAR
OBLIGATIONS OFTACPWITH RESPECTTOTHE
REPAIR OR REPLACEMENT OF ANY PARTS. IN NO
EVENT SHALLTACP BE LIABLE FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES (INCLUDING, BUT NOT
LIMITEDTO, LOST PROFITS, BUSINESS
INTERRUPTION, OR MODIFICATION OR ERASURE OF
RECORDED DATA CAUSED BY USE, MISUSE OR
INABILITYTO USETHIS PRODUCT).
No person, agent, distributor, dealer or company is
authorized to change, modify or extend the terms of these
warranties in any manner whatsoever. The time within which
an action must be commenced to enforce any obligation of
TACP arising under the warranty or under any statute, or law
of the United States or any state thereof, is hereby limited to
ninety (90) days from the date you discover or should have
discovered, the defect. This limitation does not apply to
implied warranties arising under state law.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
- IMPORTANT -
CANADIANWARRANTY INFORMATION
STANDARD WARRANTY
TYPE OF SET
DVD Player
DVD/VCR Combination
Home Theatre in a Box
DVD Recorder
Portable DVD
WARRANTY PERIOD
12 MONTHS
CANADIAN WARRANTY
Toshiba of Canada Limited (TCL) makes the following limited warranties to original consumers in Canada. Please retain your
“Bill of Sale” as proof of purchase. To obtain a “Canadian Warranty” please register online at www.toshiba.ca.
Canadian Warranty Information
Should service be required on this unit during the one year
warranty period, TCL’s option will be to repair or exchange
the defective unit. It will be necessary to follow this
procedure:
Contact: Toshiba of Canada Limited at the Consumer
Electronics Group, customer support line.
This 12-month warranty will be strictly adhered to.
Out of warranty units should be repaired by a TCL authorized
service centre.
Note: It is the responsibility of the owner to ensure proper
packaging. Should damage in shipping occur, due to poor
packaging, a charge back for the repair will result. This
warranty applies to the original purchaser only and is not
transferable.
Phone:
Email:
1-800-268-3404
This warranty does not apply to sets that have been subjected
to misuse, neglect, accident, physical damage or acts of
nature.
All in-warranty repairs must be made by an authorized TCL
service centre.
Sets with the serial number removed, altered, replaced or
defaced will not be covered by this warranty.
The warranties from TCL are effective only if the product is
purchased in Canada from an authorized TCL dealer and
operated in Canada.
Products utilized for rental or commercial purposes are not
covered by this warranty.
This warranty is in lieu of all other warranties, guaranties or
agreements, whether expressed or implied, and no person,
agent distributor, dealer, service centre or company is author-
For service exchange TCL will arrange to have the unit
picked up by courier and a replacement unit will be returned
via same courier. (Note: A major credit card number will be
required as a charge of $25.00 will apply if no fault is found
with the unit.) During the first 3 months of ownership, a new
unit will be supplied as a replacement. During the remainder
of the warranty period a service-renewed unit will be
supplied.
The original “Bill of Sale” must be provided as proof of
purchase (it will be returned with the replacement unit.)
Toshiba of Canada Limited 191 McNabb Street Markham, Ontario L3R 8H2
Printed in China
811-398091-011
Download from Www.Somanuals.com. All Manuals Search And Download.
|