14AF45
20AF45
J3S00121A(E)_COVER
1
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Installation, Care, and Service
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
Installation
Follow these recommendations and precautions and heed all
warnings when installing your TV:
4) Follow all instructions.
16) Never modify this equipment. Changes or modifications
may void: a) the warranty, and b) the user’s authority to
operate this equipment under the rules of the Federal
Communications Commission.
5) Do not use this apparatus near
water.
17)
DANGER: RISK OF SERIOUS PERSONAL
INJURY, DEATH, OR EQUIPMENT
DAMAGE! Never place the TV on
6) Clean only with a dry cloth.
an unstable cart, stand, or table. The TV
may fall, causing serious personal injury,
death, or serious damage to the TV.
7) Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
18) Never place or store the TV in direct
sunlight; hot, humid areas; areas
subject to excessive dust or vibration;
or locations with temperatures at or
below 41°F (5°C).
8) Do not install near any heat
sources such as radiators,
heat registers, stoves, or other
apparatus (including amplifiers)
that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding
19) Always place the TV on the floor
or a sturdy, level, stable surface that
can support the weight of the unit.
Wide plug
prong. The wide blade or the third
prong are provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician
for replacement of the obsolete outlet.
20) Never place items such as vases,
aquariums, or candles on top of the TV.
10) Protect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and
the point where it exits the apparatus.
11) Only use attachments/accessories specified by the
21) Never block or cover the slots or
openings in the TV cabinet back,
bottom, and sides. Never place
the TV:
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
• on a bed, sofa, rug, or similar
surface;
• too close to drapes, curtains,
or walls; or
apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
• in a confined space such as a
bookcase, built-in cabinet, or any
other place with poor ventilation.
The slots and openings are provided
to protect the TV from overheating
and to help maintain reliable
operation of the TV.
13) Unplug this apparatus during
lightning storms or when
unused for long periods
of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply
cord or plug is damaged, liquid has
22) Never allow anything to rest on or roll over the power
cord, and never place the TV where the power cord is
subject to wear or abuse.
been spilled or objects have fallen into
the apparatus, the apparatus has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
QUALIFIED
SERVICE
TECHNICIAN
23) Never overload wall outlets and
extension cords.
15)
CAUTION: To reduce the risk of electric shock, do
not use the polarized plug with an extension cord,
receptacle, or other outlet unless the blades can
be inserted completely to prevent blade exposure.
0303
3
3
J3S00121A(E)_P02-06
3
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
30) [This item applies to projection TVs only.] If the air
temperature rises suddenly (for example, when the TV is
first delivered), condensation may form on the lenses. This
can make the picture appear distorted or the color appear
faded. If this happens, turn off the TV for 6 to 7 hours to
allow the condensation to evaporate.
24) Always operate this equipment from
a 120V AC, 60 Hz power source only.
31) For added protection of your TV from lightning and power
surges, always unplug the power cord and disconnect the
antenna from the TV if you leave the TV unattended or
unused for long periods of time.
25) Always make sure the antenna system is properly
grounded to provide adequate protection against voltage
surges and built-up static charges (see Section 810 of the
National Electric Code).
Antenna lead-in wire
32) During normal use, the TV may make
occasional snapping or popping
Antenna discharge unit
(NEC Section 810-20)
Ground clamp
sounds. This is normal, especially
when the unit is being turned on or
off. If these sounds become frequent
or continuous, unplug the power cord
and contact a Toshiba Authorized Service Center.
Grounding conductors
(NEC Section 810-21)
Electric service equipment
Power service grounding
33) Possible Adverse Effects on TV Picture Tube: If a fixed
(non-moving) pattern remains on the TV screen for long
periods of time, the image can become permanently
ingrained in the picture tube and cause subtle but
permanent ghost images. This type of damage is NOT
COVERED BY YOUR WARRANTY. Never leave your TV
on for long periods of time while it is displaying the
following formats or images:
electrode system (NEC Art 250 Part H)
Ground clamps
26)
DANGER: RISK OF SERIOUS PERSONAL
INJURY OR DEATH!
• Use extreme care to make sure you are never in
a position where your body (or any item you are in contact
with, such as a ladder or screwdriver) can accidentally
touch overhead power lines. Never locate the antenna
near overhead power lines or other electrical circuits.
• Never attempt to install any of the following during
lightning activity:
a) an antenna system; or b) cables, wires, or any home
theater component connected to an antenna or phone
system.
• Fixed Images, such as PIP/POP windows, stock tickers,
video game patterns, TV station logos, closed captions,
and websites.
• Special Formats that do not use the entire screen. For
example, viewing letterbox style (16:9) media on a
normal (4:3) display (gray bars at top and bottom of
screen); or viewing normal style (4:3) media on a
widescreen (16:9) display (gray bars on left and right
sides of screen).
Care
Service
34)
For better performance and safer operation of your TOSHIBA
TV, follow these recommendations and precautions:
WARNING: RISK OF ELECTRIC
SHOCK! Never attempt to service the
TV yourself. Opening and
27) Always sit approximately 10–25 feet away from the TV and
as directly in front of it as possible. The picture can appear
dull if you sit too far to the left or right of the TV, or if
sunlight or room lights reflect on the screen. Turn the TV
off to check for reflections on the screen, and then remove
the source of reflections while viewing the TV.
removing the covers may expose
you to dangerous voltage or other
hazards. Refer all servicing to a
Toshiba Authorized Service Center.
QUALIFIED
SERVICE
TECHNICIAN
35) If you have the TV serviced:
• Ask the service technician to use only replacement parts
specified by the manufacturer.
28) Always unplug the TV before
cleaning. Never use liquid or
aerosol cleaners.
• Upon completion of service, ask
the service technician to perform
routine safety checks to determine
that the TV is in safe operating
condition.
36) When the TV reaches the end of its useful life, ask a
qualified service technician to properly dispose of the TV.
Improper disposal may result in a picture tube implosion
and possible personal injury.
29)
WARNING: RISK OF ELECTRIC SHOCK!
Never spill liquids or push objects of any kind
into the TV cabinet slots.
0303
4
J3S00121A(E)_P02-06
4
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information .......................................................................................... 2-4
Welcome to Toshiba............................................................................................................ 6
Exploring your new TV ................................................................................................................................6
Selecting a location for the TV ....................................................................................................................6
Connecting your TV ............................................................................................................ 7
Connecting a VCR .......................................................................................................................................7
Connecting a cable converter box ...............................................................................................................8
Connecting a DVD player/satellite receiver and a VCR ..............................................................................9
Connecting a DVD player with ColorStream® (component video) and a VCR............................................9
Connecting a camcorder ...........................................................................................................................10
Using the remote control...................................................................................................11
Installing the remote control batteries ....................................................................................................... 11
Learning about the remote control ............................................................................................................ 11
Setting up your TV ............................................................................................................ 12
Changing the on-screen display language ................................................................................................12
Adding channels to the TV’s memory........................................................................................................13
Programming channels automatically ................................................................................................13
Adding and erasing channels manually .............................................................................................13
Changing channels ....................................................................................................................................13
Using the TV’s features .................................................................................................... 14
Adjusting the channel settings...................................................................................................................14
Switching between two channels .......................................................................................................14
Programming your favorite channels .................................................................................................14
Using theV-Chip (parental control) feature (U.S. V-Chip system only) .....................................................15
Selecting a PIN code ..........................................................................................................................15
Blocking programs by ratings .............................................................................................................16
Blocking unrated movies or programs................................................................................................19
Using the LOCK menu...............................................................................................................................19
Locking channels ................................................................................................................................19
Locking video input.............................................................................................................................20
Setting the GameTimerTM ...........................................................................................................................20
Labeling channels......................................................................................................................................21
Setting the clock ........................................................................................................................................22
Setting the ON/OFF timer ..........................................................................................................................22
Setting the on timer ............................................................................................................................22
Setting the off timer ............................................................................................................................23
Adjusting the picture quality ......................................................................................................................24
Watching video input .................................................................................................................................24
Specifying the ColorStream® setting .........................................................................................................24
Displaying on-screen information ..............................................................................................................24
Setting the sleep timer ...............................................................................................................................25
Using the closed caption feature ...............................................................................................................25
Changing the picture size ..........................................................................................................................25
Adjusting the sound ...................................................................................................................................26
Muting the sound ................................................................................................................................26
Selecting stereo/SAP broadcasts .......................................................................................................26
Adjusting the sound quality ................................................................................................................27
Using the surround sound feature ......................................................................................................27
Using the StableSound® feature .........................................................................................................28
Auto power off............................................................................................................................................28
Understanding the Power Return feature..................................................................................................28
Appendix ............................................................................................................................ 29
Troubleshooting .........................................................................................................................................29
Specifications.............................................................................................................................................30
Limited United States Warranty .................................................................................................................31
5
J3S00121A(E)_P02-06
5
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Welcome to Toshiba
Congratulations! You have purchased one of the finest color TVs on
the market. The goal of this manual is to guide you through setting up
and operating your Toshiba TV as quickly as possible.
You may need to purchase other audio or video cables to connect your
equipment. See “Connecting your TV” on page 7 for more information.
Please read all the safety and operating instructions carefully before
you begin.
Exploring your new TV
You can operate your TV by using the buttons on the front panel or the
remote control. The front and back panels provide all the inputs you will
need to connect other equipment to your TV.
14AF45
Remote
sensor
Channel
Audio(L/R)/Video In
Phones
POWER
Power
Volume
indicator
20AF45
TV front panel
16:9
IN
Y
P
VIDEO
ANT (75Ω)
B
R
L/MONO
S-VIDEO
AUDIO
R
P
VIDEO 1
TV back panel
Selecting a location for the TV
• Place the TV on the floor or on a sturdy platform in a location where
light does not directly hit the screen.
• Place the TV far enough from the walls to allow proper ventilation.
Inadequate ventilation may cause overheating, which may damage
the TV.
6
J3S00121A(E)_P02-06
6
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your TV
• A coaxial cable is the standard cable that comes in from your
antenna or cable converter box. Coaxial cables use “F” connectors.
• Standard A/V (audio/video) cables are usually color coded accord-
ing to use: yellow for video and red and white for audio. The red
audio cable is for the stereo right channel, and the white audio
cable is for the stereo left (or mono) channel. If you look at the rear
panel of the TV, you will see that the terminals are color coded in
the same manner as the cables.
• An S-video cable provides better picture performance than a
standard video cable. S-video cables can only be used with S-video
compatible components.
• Component video cables come in sets of three and provide the best
picture performance. Component video cables can only be used
with component video compatible components.
NOTICE: RISK OF
EQUIPMENT DAMAGE!
Do not plug in any power cords
until you have finished connecting
all equipment.
S-Video
Cable
ANTENNA
Coaxial Cable
AUDIO
Cables
Component video
Cables
VIDEO
Cable
Connecting a VCR
This connection allows you to watch local channels and video programs,
play or record on the VCR while watching TV, and record from one
channel while watching another channel.
You will need:
• two coaxial cables
• one set of standard A/V cables
TV
Note:
IN
Y
If using a mono VCR, connect L/Mono to
VCR Audio OUT using only one audio cable.
For better picture quality, if your VCR has S-
video, you can use an S-video cable instead
of the standard video cable. Do not connect a
standard video cable and an S-video cable to
VIDEO1 simultaneously.
VIDEO
ANT (75Ω)
P
P
B
R
L/MONO
S-VIDEO AUDIO
R
VIDEO
1
Cable Lead-in
from cable box
or antenna
The unauthorized recording, use, distribu-
tion or revision of television programs,
videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of the
United States and other countries, and may
subject you to civil and criminal liability.
Stereo VCR
IN
IN from ANT
OUT to TV
OUT
CH
CH
3
4
L
R
VIDEO
AUDIO
7
J3S00121A(E)_P07-13
7
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a cable converter box
This television has an extended tuning range and can tune most cable
channels without using a cable company supplied converter box. Some
cable companies offer “premium pay channels” in which the signal is
scrambled. Descrambling these signals for normal viewing requires the
use of a descrambler device, which is generally provided by the cable
company.
For Subscribers to Basic Cable TV Service
For basic cable service not requiring a Converter/Descrambler box,
connect the CATV 75 ohm Coaxial Cable directly to the Antenna Jack
on the back of the television.
For Subscribers to Scrambled Cable TV Service
If you subscribe to a cable service that requires the use of a Converter/
Descrambler box, connect the incoming cable to the Converter/
Descrambler box and connect the output of the box to the Antenna
Jack on the back of the television. Follow the connections shown
below. Set the television to the output of the Converter/Descrambler
box (usually channel 3 or 4) and use the Converter/Descrambler box to
select channels.
For Subscribers to Unscrambled Basic Cable with
Scrambled Premium Channels
If you subscribe to a cable service in which basic cable channels are
unscrambled and premium channels require the use of a Converter/
Descrambler box, you may wish to use a two-set signal splitter (some-
times called a “two-set coupler”) and an A/B Switch box from the cable
installer or an electronics supply store. Follow the connections shown
below. With the switch in the “B” position, you can directly tune any
nonscrambled channels on your TV. With the switch in the “A” position,
tune your TV to the output of the Converter/Descrambler box (usually
channel 3 or 4) and use the box to tune scrambled channels.
Note:
When you use a converter box with your TV,
there may be features that you cannot
program using the remote control, such as
labeling channels, blocking channels, and
programming your favorite channels.
Incoming CATV
IN
Y
VIDEO
ANT (75Ω)
Converter/Descrambler
P
P
B
R
L/MONO
S-VIDEO AUDIO
Converter/Descrambler
R
VIDEO
1
A
Splitter
A/B Switch
B
8
J3S00121A(E)_P07-13
8
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
You will need:
Connecting a DVD player/satellite receiver
and a VCR
This connection allows you to watch DVD/satellite, VCR, or TV pro-
grams.
• three coaxial cables
• two sets of standard A/V cables
• one S-video cable
Note:
To satellite
DVD player/ Satellite Receiver
You can use a standard video cable instead of
the S-video cable, but the picture quality will
decrease. If you use an S-video cable
between the TV and DVD player/satellite
receiver, make the audio connections but
remove the standard video cable. Do not
connect both an S-video and a standard video
cable to VIDEO1 at the same time or the
picture performance will be unacceptable.
VIDEO
AUDIO
L
R
OUT
Satellite IN
S-VIDEO
OUT to TV
Stereo VCR
IN
IN from ANT
OUT to TV
OUT
CH
CH
3
4
The unauthorized recording, use, distribu-
tion or revision of television programs,
videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of the
United States and other countries, and may
subject you to civil and criminal liability.
VIO
AUDIO
TV
IN
Y
P
VIDEO
ANT (75Ω)
B
R
L/MONO
S-VIDEO
DIO
P
R
VIDEO
1
Connecting a DVD player with ColorStream®
(component video) and a VCR
You will need:
• two coaxial cables
This connection allows you to watch DVD, VCR, or TV programs and
record TV programs. You can record from one source while watching a
program from another source. Your TV is capable of using ColorStream
(component video). Connecting your TV to a component video compat-
ible DVD player, such as a Toshiba DVD player with ColorStream®, can
greatly enhance picture quality and performance.
• one set of component video cables
• one pair of standard audio cables
Note:
The ColorStream inputs on this TV are for use
with devices that output 480i interlaced
signals ONLY. This TV will not accept or
display 480p or 720p progressive scan
signals or 1080i interlaced high-definition
signals. If you connect a high-definition set-
top receiver, 480p progressive scan DVD
player, or other similar device to the TV’s
ColorStream inputs, YOU MUST SWITCH
THE DEVICE’S OUTPUT TO 480i INTER-
LACED MODE FIRST. Failure to do this will
cause a poor picture or no picture to display.
DVD player with ColorStream®
OUT
L
COLORSTREAMTM
Cb
R
Y
Cr
AUDIO
VIDEO
OUT
S-VIDEO
TV
IN
Y
P
VIDEO
ANT (75Ω)
B
R
L/MONO
S-VIDEO
DIO
P
The unauthorized recording, use, distribu-
tion or revision of television programs,
videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of the
United States and other countries, and may
subject you to civil and criminal liability.
R
VIDEO
1
To antenna
Stereo VCR
IN
IN from ANT
OUT to TV
OUT
CH
CH
3
4
L
R
VIDEO
AUDIO
9
J3S00121A(E)_P07-13
9
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a camcorder
This connection allows you to watch video materials recorded on a
You will need:
• one set of standard A/V cables
camcorder.
Camcorder
Note:
AUDIO
VIDEO
For better picture quality, if your camcorder
has S-video, you can connect an S-video
(and standard audio cables) to VIDEO1 on
the back of the TV. Do not connect a standard
video cable and an S-video cable to VIDEO1
simultaneously.
L
R
OUT
AUDIO
VIDEO 2 LNO PHONES
Front Panel of TV
10
J3S00121A(E)_P07-13
10
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the remote control
Installing the remote control batteries
To install the batteries:
1. Open the battery cover on the back of the remote control.
Caution:
• Never throw batteries into a fire.
Notes:
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated
disposal area.
• Attention should be drawn to the environ-
mental aspects of battery disposal.
• Do not mix different battery types or
combine used batteries with new ones.
• If the remote control does not operate
correctly, or if the operating range becomes
reduced, replace both batteries with new
ones.
2. Install two “AAA” size batteries. Match the + and – signs on the
batteries to the signs on the battery compartment.
• If the batteries are dead or if you will not be
using the remote control for a long time,
remove the batteries to prevent battery acid
from leaking into the battery compartment.
3. Close the battery cover on the remote control until the lock snaps.
Learning about the remote control
POWER turns the TV on and off
CHANNEL NUMBERS allow direct access to channels (page 13)
RECALL displays status information on-screen (page 24)
SLEEP programs the TV to turn off at a set time (page 25)
MUTE turns off the sound (page 26)
POWER
Channel
Numbers
CH + / – cycles through programmed channels (page 13)
VOLUME + / – adjusts the volume level
Recall
Sleep
MENU/ENTER allows access to programming menus, and sets
programmed menu information (page 12)
Mute
CH +/-
EXIT closes on-screen menus (page 12)
Volume +/-
CAP/TEXT turns closed captions or text on and off (page 25)
1/2 selects closed caption/text channel 1 or 2 (page 25)
RESET returns settings to preset factory formats (pages 24 and 27)
Menu/Enter
CAP/TEXT
Exit
1/2
MTS
CH RTN
(Channel Return)
FAV L/M
(Favorite
Channels)
Reset
TV/Video
16:9
16:9
CH RTN (Channel Return) returns to the last viewed channel
(page 14)
MTS switches among STEREO, SAP, and MONO sound (page 26)
TV/VIDEO selects the video input source (page 24)
FAV L/M (Favorite Channels) cycle through favorite channels
(page 14)
16:9 toggles the aspect ratio between 4:3 (letterbox) and 16:9 (wide
screen) modes (page 25)
11
J3S00121A(E)_P07-13
11
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
After you have installed the batteries and programmed the remote
control, you need to set some preferences on the TV using the menu
system. You can access the menu system with the buttons on the
remote control.
• When you make a menu selection, your changes occur immediately.
You do not have to press MENU or EXIT to see your changes.
• After five seconds, the menu screen will automatically close if you
do not make a selection. Your changes will still be saved.
• When you are finished programming the menus, press EXIT.
Changing the on-screen display language
You can choose from three different languages (English, French, and
Spanish) for the on-screen display of adjustment menus and
messages.
To select a language:
1. Press MENU, then press a or b until the OPTION menu appears.
CH
PICTURE AUDIO SETUP OPTION
LANGUAGE
ENGLISH
c d a b
CH LABEL
FAVORITE CH
V-CHIP
START
START
START
START
OFF
LOCK
ON/OFF TIMER
COLORSTREAM DVD
SELECT
ADJUST
Exit
Menu
2. Press c or d to highlight LANGUAGE.
CH
PICTURE AUDIO SETUP OPTION
LANGUAGE
ENGLISH FRANCAIS
ESPANOL
CH LABEL
FAVORITE CH
V-CHIP
START
START
START
START
OFF
LOCK
ON/OFF TIMER
COLORSTREAM DVD
SELECT
ADJUST
3. Press a or b to highlight your desired language.
12
J3S00121A(E)_P07-13
12
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding channels to the TV’s memory
When you press CH +/- on the remote control or CHANNEL c/d on the
TV front panel, your TV will stop only on the channels stored in the
TV’s channel memory. Follow the steps below to program channels into
the memory.
Programming channels automatically
Your TV can automatically detect all active channels and store them in
its memory. After the TV has stored the channels in its memory
automatically, you can add or erase specific channels manually.
To add channels automatically:
1. Press MENU, then press a or b to display the SETUP menu.
2. Press c or d until the TV/CABLE
selection is highlighted.
CH
3. Press a or b to highlight either TV
PICTURE AUDIO SETUP OPTION
Channel
Numbers
or CABLE, depending on which
you use.
TV / CABLE
TV CABLE
START
CH PROGRAM
ADD / ERASE
ADD
If you use an antenna, choose TV.
If you use cable, choose CABLE.
SELECT
ADJUST
Channel +/–
4. Press d to select CH PROGRAM.
5. Press
a
or
b
to start channel programming. The TV will automatically
c d a b
cycle through all the TV or Cable channels (depending on which you
selected), and store all active channels in the channel memory.
While the TV is cycling through the channels, the message
“PROGRAMMING NOW-PLEASE WAIT” appears.
6. When channel programming is complete, the message “COMPLETED”
appears.
Menu
7. Press CH + or – to view the programmed channels.
Adding and erasing channels manually
After you have programmed the channels automatically, you can add
or erase specific channels manually.
To add or erase channels manually:
1. Select the channel you want to add or erase.
If you are adding a channel, you must select the channel using the
Channel Number buttons.
2. Press MENU, then press a or b to
display the SETUP menu.
3. Press c or d to highlight ADD/
CH
PICTURE AUDIO SETUP OPTION
ERASE.
TV / CABLE
CABLE
CH PROGRAM
ADD / ERASE
START
4. Press a or b to select ADD or
ERASE, whichever function you
want to perform.
5. Repeat steps 1–4 for other
channels you want to add or erase.
ADD ERASE
SELECT
ADJUST
Changing channels
To change to the next programmed channel:
Press CHANNEL c/d on the TV front panel or CH +/– on the
remote control.
To change to a specific channel (programmed or unprogrammed):
Press the Channel Number buttons (0–9 and 100) on the remote
control.
For example, to select channel 125, press 100, 2, 5.
13
J3S00121A(E)_P07-13
13
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Adjusting the channel settings
Switching between two channels
You can switch between two channels without entering an actual
channel number each time.
Channel
Numbers
To switch between two channels:
1. Select the first channel you want to view.
2. Select a second channel using the Channel Number buttons (0–9,
100).
3. Press CH RTN. The previous channel will be displayed.
Each time you press CH RTN, the TV will switch back and forth
between the two channels.
Programming your favorite channels
You can preset up to 12 of your favorite channels using the Favorite
Channel Programming feature. Because this feature scans through
only your favorite channels, it allows you to skip other channels you
do not normally watch.
CH RTN
You can still use Channel + / – to scan through all the channels you
programmed in the TV’s memory.
To program your favorite channels:
1. Select a channel you want to program as a favorite channel.
2. Press MENU, then press aor bto display the OPTION menu.
3. Press cor dto highlight FAVORITE CH.
CH
Channel
Numbers
PICTURE AUDIO SETUP OPTION
LANGUAGE
ENGLISH
CH LABEL
FAVORITE CH
V-CHIP
START
START
START
START
OFF
LOCK
ON/OFF TIMER
COLORSTREAM DVD
SELECT
START
cd ab
4. Press aor bto display the FAVORITE CH menu. SET/CLEAR will
be highlighted.
Exit
Menu/
Enter
CH
PICTURE AUDIO SETUP OPTION
FAVORITE CH : CH 012
SET/CLEAR
SET UP CH
SET CLEAR
FAV
0
0
0
0
0
0
0
0
0
0
0
0
16:9
TV CABLE
SELECT
SET
ENTER
END
EXIT
5. Press aor bto highlight SET and press ENTER.
6. Press EXIT to close the screen.
7. Repeat steps 1–6 for up to 11 other channels.
To select your favorite channels:
Press the FAV LM buttons on the remote control to select your
favorite channels.
The FAV LM buttons will not work until you have programmed
your favorite channels.
14
J3S00121A(E)_P14-25
14
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
To clear your favorite channels:
1. Select a channel you want to clear.
2. Press MENU, then press aor bto display the OPTION menu.
3. Press cor dto highlight FAVORITE CH.
4. Press aor bto display the FAVORITE CH menu. SET/CLEAR will
be highlighted.
Channel
Numbers
CH
PICTURE AUDIO SETUP OPTION
FAVORITE CH : CH 012
SET/CLEAR
SET UP CH
SET CLEAR
7
36
4
1
12 125 63 40
13 28 97 112
TV CABLE
SELECT
cd ab
SET
ENTER
END
EXIT
5. Press aor bto highlight CLEAR.
Exit
Menu/
Enter
CH
PICTURE AUDIO SETUP OPTION
FAVORITE CH : CH 012
SET/CLEAR
SET UP CH
SET CLEAR
7
36
4
1
12 125 63 40
13 28 97 112
TV CABLE
SELECT
CLEAR
ENTER
END
EXIT
6. Press ENTER until “0” replaces the channel number you want to
erase.
7. Press EXIT to clear the screen.
8. Repeat steps 1–6 for the other channels.
Using the V-Chip (parental control) feature
The V-Chip feature is available only for the U.S. V-Chip system.
The Canadian V-Chip system is not supported.
You can prevent others from viewing certain programs or channels by
blocking them using the V-Chip feature.
Selecting a PIN code
Before you can block programs and channels, you must select a
personal identification number (PIN) code. The PIN code you select
prevents others from changing the rating limits you set.
To select your PIN code and access the V-Chip menus:
1. Press MENU, then press aor bto highlight the OPTION menu.
2. Press cor dto highlight V-CHIP.
CH
cd ab
PICTURE AUDIO SETUP OPTION
LANGUAGE
ENGLISH
CH LABEL
FAVORITE CH
V-CHIP
START
START
START
START
OFF
LOCK
ON/OFF TIMER
COLORSTREAM DVD
SELECT
START
Menu
Note:
The PIN code you programmed is also used in the LOCK menu; see
pages 19 and 20.
15
J3S00121A(E)_P14-25
15
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press aor b to display the V-CHIP menu.
CH
PICTURE AUDIO SETUP OPTION
V-CHIP
Note:
BLOCKING
PIN CODE
RESET
SET
If you forget your PIN code, press RECALL
four times within five seconds from the V-CHIP
menu. This allows you to proceed to the
BLOCKING menu and resets your PIN code.
SELECT
END
ENTER
[0-9]
EXIT
4. Use the Channel Number buttons (0–9) to enter your PIN code.
If you are accessing the V-Chip menus for the first time, select a
four-digit number to be your PIN code. Press ENTER. The
BLOCKING menu appears.
CH
PICTURE AUDIO SETUP OPTION
V-CHIP
ENABLE BLOCKING ON OFF
SET RATING
BLOCKING OPTION START
START
NEW PIN CODE
START
SELECT
ADJUST
5. You may now enable blocking. See “Blocking programs by ratings”
(below), “Locking channels” (page 19), “To change your PIN code”
(below), or “Blocking unrated movies or programs” (page 19).
To change your PIN code:
1. Press MENU, then press aor bto display the OPTION menu.
2. Press cor dto highlight V-CHIP.
3. Press aor bto display the V-CHIP menu.
4. Use the Channel Number buttons (0–9) to enter your PIN code.
Press ENTER. The BLOCKING menu appears.
5. Press cor dto highlight NEW PIN CODE and press aor bto
display the NEW PIN CODE menu.
6. Use the Channel Number buttons (0–9) to enter a new code.
Press ENTER.
7. Press EXIT to return to normal viewing.
Blocking programs by ratings
The Motion Picture Association of America (MPAA) uses a rating
system to qualify motion picture content. Television broadcasters
employ a rating system to qualify the content of television programs, as
well. The MPAA, Youth TV, and TV ratings work with the V-Chip feature
and allow you to block programs according to the rating limits you set.
Channel
Numbers
Recall
cd ab
Exit
Menu/
Enter
16
J3S00121A(E)_P14-25
16
13/01/2005, 5:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
MPAA Ratings
X
For adults only.
NC17
R
Not intended for anyone 17 or under.
Restricted. Under 17 requires an accompanying
parent or adult guardian.
PG13
PG
Parents strongly cautioned. Some material may be
inappropriate for children under 13.
Parental guidance suggested. Some material may
not be appropriate for children.
G
General audience. Appropriate for all ages.
Youth TV Ratings
Y7FV, Y7
Directed to older children. This program is designed
for children age 7 and above. Programs in which
fantasy violence may be more intense or combative
than other programs in this category are designated
TV-Y7-FV.
Y
All children. This program is designed to be appropri-
ate for all children.
Note:
TV Ratings
To see the rating of the program you are
viewing, press RECALL at any time.
MA
Mature audience only. This program is specifically
designed to be viewed by adults and therefore may
be unsuitable for children under 17.
Language
Sex
Violence
Crude or indecent language.
Explicit sexual activity.
Graphic violence.
14
Parents strongly cautioned. This program contains
some material that many parents would find unsuit-
able for children under 14 years of age.
Dialog
Language
Sex
Intensely suggestive dialog.
Strong, coarse language.
Intense sexual situations.
Intense violence.
Violence
PG
Parental guidance suggested. This program contains
material that parents may find unsuitable for younger
children.
Dialog
Language
Sex
Some suggestive dialog.
Infrequent coarse language.
Some sexual situations.
Moderate violence.
Violence
G
General audience. Most parents would find this
program suitable for all ages.
No DLSV
Programs not rated according to Dialog, Language,
Sex or Violence.
17
J3S00121A(E)_P14-25
17
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the V-Chip to block programs by rating:
1. Press MENU, then press aor bto display the OPTION menu.
2. Press cor dto highlight V-CHIP.
3. Press aor b to display the V-CHIP menu.
4. Use the Channel Number buttons (0–9) to enter your PIN code.
If you are accessing the V-Chip menus for the first time, select a
four-digit number to be your PIN code. Press ENTER.
The BLOCKING menu appears.
Channel
Numbers
CH
PICTURE AUDIO SETUP OPTION
V-CHIP
ENABLE BLOCKING ON OFF
cd ab
SET RATING
BLOCKING OPTION START
START
NEW PIN CODE
START
SELECT
ADJUST
Exit
5. Press cor dto highlight ENABLE BLOCKING.
• Press aor bto highlight ON to enable V-Chip program blocking
by rating.
Menu/
Enter
• Press aor bto highlight OFF to disable V-Chip program blocking
by rating.
6. Press cor d to highlight SET RATING. Then, press aor bto
display the SET RATING menu.
CH
CH
PICTURE AUDIO SETUP OPTION
PICTURE AUDIO SETUP OPTION
SET RATING
TV RATING
MA 14 PG
G
MPAA
DIALOG
LANGUAGE
SEX
X NC17 R PG13 PG G
Y7FV Y7 Y
RATING
YOUTH TV
RATING
VIOLENCE
NO DLSV
MORE
SELECT
V-CHIP MENU
SELECT
START
ADJUST
ADJUST
7. Press cor dto highlight MPAA Rating, Youth TV Rating or
individual TV Ratings.
8. Press aor bto select the ratings that will be blocked. Blocked
ratings are signified by a red “X.” Unblocked ratings are signified
by a green “ꢀ.” As you block ratings, all ratings higher than the
ones you select are blocked, as well. For example, if you choose
to block the MPAA rating R, the higher ratings NC17 and X are
automatically blocked too.
Note:
Not all programs are rated. To block programs
or movies that are unrated, see “Blocking
unrated movies or programs,” page 19.
9. When you are done selecting the ratings to be blocked, press
EXIT to return to normal viewing.
When you try to view a program with a ratings block, a message will
appear listing the program’s ratings. The program can still be viewed if
you press MUTE and then enter your PIN code to temporarily bypass
the block.
18
J3S00121A(E)_P14-25
18
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Blocking unrated movies or programs
Some movies and programs are not rated. You can block these movies
and programs using the V-Chip.
To block unrated movies or programs:
1. Press MENU, then press aor bto display the OPTION menu.
2. Press cor dto highlight V-CHIP.
3. Press aor bto display the V-CHIP menu.
4. Use the Channel Number buttons (0–9) to enter your PIN code.
If you are accessing the V-Chip menus for the first time, select a
four-digit number to be your PIN code. Press ENTER.
The BLOCKING menu appears.
5. Press cor dto highlight BLOCKING OPTION.
6. Press aor bto display the BLOCKING OPTION menu.
7. Press cor dto highlight MPAA UNRATED.
• Press aor bto highlight ON to block unrated movies.
• Press aor bto highlight OFF to unblock unrated movies.
8. Press cor dto highlight TV NONE RATING.
• Press aor b to highlight ON to block programs with a rating of
“TV NONE.” When you select ON, the message “NOTICE:
ENABLING THIS OPTION MAY BLOCK EMERGENCY
MESSAGES” appears.
Note:
Blocking television programs with a rating of
“TV NONE” may block emergency messages.
• Press aor bto highlight OFF to unblock programs with a rating
of “TV NONE.”
9. Press EXIT to return to normal viewing.
Using the LOCK menu
The LOCK menu includes the CH LOCK, VIDEO LOCK, GAME TIMER,
and NEW PIN CODE functions.
You can use these functions after entering the correct PIN code. (This
PIN code is the same one selected under “Selecting a PIN code” on
page 15.)
Locking channels
With the CH LOCK feature, you can lock specific channels. You will not
be able to tune locked channels unless you clear the setting. You can
choose to lock up to nine TV channels and nine cable channels.
Channel
Numbers
To lock channels:
1. Use the Channel Number buttons (0–9) to display the television
channel you wish to lock.
2. Press MENU, then press aor b to display the OPTION menu.
3. Press cor dto highlight LOCK.
cd ab
4. Press aor bto display the LOCK menu.
5. Use the Channel Number buttons (0–9) to enter your PIN code,
then press ENTER. The LOCK menu
appears.
CH
Exit
Menu/
Enter
PICTURE AUDIO SETUP OPTION
6. Press cor dto highlight CH LOCK
and press aor bto display the CH
LOCK menu.
LOCK
CH LOCK
VIDEO LOCK
START
OFF
7. Press aor bto select the following:
• SET– to set the channel as one to be
locked. Then press ENTER.
OFF
GAME TIMER
NEW PIN CODE START
SELECT ADJUST
Note:
• CLEAR– to clear all channels from
the list of locked channels.
Then press ENTER.
After programming CH LOCK, change
channels before turning off the television.
CH
PICTURE AUDIO SETUP OPTION
8. Repeat steps 1 through 7 to lock other
channels. When you are finished
locking channels, press EXIT to return
to normal viewing.
CH LOCK : CH 12
SET/CLEAR
LOCKED CH
SET CLEAR
0
0
0
0
0
0
0
0
0
TV CABLE
SELECT
SET
ENTER
If you try to tune a locked channel, the
TV will not display it, but will display the
nearest unlocked channel.
END
EXIT
19
J3S00121A(E)_P14-25
19
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
To unlock channels:
1. Press MENU, then press aor b to display the OPTION menu.
2. Press cor dto highlight LOCK and then press aor b to display
the LOCK menu.
3. Use the Channel Number buttons (0–9) to enter your PIN code,
then press ENTER. The LOCK menu appears.
4. Press cor dto highlight CH LOCK and press aor b to display
the CH LOCK menu.
5. Press aor b to highlight CLEAR, and then press ENTER. This
clears all channels from the list of locked channels.
6. Press EXIT to return to normal viewing.
Locking video input
With the VIDEO LOCK feature, you can lock out the input sources
(VIDEO1, VIDEO2, COLORSTREAM) and channels 3 and 4.
You will not be able to select the input sources with the TV/VIDEO
button or Channel buttons unless you clear the setting.
To set up the video lock:
1. Press MENU, then press aor b to display the OPTION menu.
2. Press cor dto highlight LOCK.
Channel
Numbers
3. Press aor b to display the LOCK menu.
4. Use the Channel Number buttons (0–9) to enter your PIN code,
then press ENTER. The LOCK menu appears.
5. Press cor dto highlight VIDEO LOCK.
6. Press aor b to select:
cd ab
• OFF: Unlocks all video input
sources.
CH
PICTURE AUDIO SETUP OPTION
•
VIDEO: Locks VIDEO1, VIDEO2
and COLORSTREAM.
LOCK
CH LOCK
START
• VIDEO +: Locks VIDEO1, VIDEO2,
COLORSTREAM, channel 3 and
channel 4. This option should be
used if you use the antenna terminal
to play a video tape.
VIDEO LOCK
OFF
Exit
Menu/
Enter
VIDEO VIDEO+
OFF
GAME TIMER
NEW PIN CODE START
SELECT ADJUST
Note:
After programming VIDEO LOCK, change
channels or activate the TV/VIDEO key before
turning off the television.
7. Press EXIT to return to normal viewing.
Setting the GameTimerTM
With the GameTimerTM feature, you can automatically activate the
VIDEO LOCK feature (VIDEO setting) to set a time limit for playing a
TV game (30, 60, 90 or 120 minutes).
To set up the GameTimer:
1. Press MENU, then press aor bto display the OPTION menu.
2. Press cor dto highlight LOCK.
3. Press aor b to display the LOCK menu.
4. Use the Channel Number buttons (0–9) to enter your PIN code,
then press ENTER. The LOCK menu appears.
5. Press cor dto highlight GameTimer.
Channel
Numbers
6. Press aor b to select a time limit (30 minutes, 60 minutes, 90
minutes, 120 minutes or OFF).
7. Press EXIT to return to normal
cd ab
CH
viewing. After the GameTimer is
programmed, the display will appear
briefly every ten minutes to remind you
that the GameTimer is operating.
When the programmed time is
reached, the display will change the
channel automatically.
PICTURE AUDIO SETUP OPTION
LOCK
CH LOCK
VIDEO LOCK
START
OFF
Exit
Menu/
Enter
GAME TIMER
OFF 30 60 90 120
NEW PIN CODE START
SELECT ADJUST
20
J3S00121A(E)_P14-25
20
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Labeling channels
Channel labels appear over the channel number display each time you
turn on the TV, select a channel, or press the Recall button. You can
choose any four characters to identify a channel.
To create channel labels:
1. Select a channel you want to label.
2. Press MENU, then press aor b until the OPTION menu appears.
3. Press cor dto highlight CH LABEL.
Channel
Numbers
CH
PICTURE AUDIO SETUP OPTION
LANGUAGE
ENGLISH
CH LABEL
FAVORITE CH
V-CHIP
START
START
START
START
OFF
cd ab
LOCK
ON/OFF TIMER
COLORSTREAM DVD
SELECT
START
4. Press aor bto display the CH LABEL menu. SET/CLEAR will be
Exit
Menu/
Enter
highlighted.
CH
PICTURE AUDIO SETUP OPTION
CH LABEL : CH 12
SET/CLEAR
LABEL
SET CLEAR
SELECT
END
SET
ENTER
EXIT
5. Press aor bto highlight SET.
6. Press cor dto highlight LABEL.
CH
PICTURE AUDIO SETUP OPTION
CH LABEL : CH 12
SET/CLEAR
LABEL
SET
SET
SELECT
ENTER
END
EXIT
7. Press aor bto enter a character in the
first space. Press the button repeatedly
until the character you want appears
on the screen. Press ENTER.
8. Repeat step 7 to enter the rest of the
characters.
Note:
CH
The character will change as below.
PICTURE AUDIO SETUP OPTION
• • •
• • •
CH LABEL : CH 12
–
0
9
A
SET/CLEAR
LABEL
SET
A
+
Z
SPACE
–
SELECT
SET
ENTER
If you would like a blank space in the
label name, you must choose a blank
END
EXIT
space from the list of characters; otherwise, a dash will appear in
that space.
9. Repeat steps 1–8 for other channels. You can assign a label to
each channel.
10. Press EXIT to clear the screen.
To erase channel labels:
1. Select a channel with a label.
2. Press MENU, then press aor b until the OPTION menu appears.
3. Press cor dto highlight CH LABEL.
4. Press aor b to display the CH LABEL menu.
SET/CLEAR will be highlighted.
5. Press aor b to highlight CLEAR.
6. Press ENTER.
7. Repeat steps 1–6 to erase other channel labels.
21
J3S00121A(E)_P14-25
21
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the clock
You must set the clock before you can program the ON/OFF timer.
To set the clock: (Example: 8:30 AM)
1. Press MENU, then press aor bto display the OPTION menu.
2. Press cor dto highlight ON/OFF TIMER.
CH
PICTURE AUDIO SETUP OPTION
LANGUAGE
ENGLISH
CH LABEL
FAVORITE CH
V-CHIP
START
START
START
START
LOCK
ON/OFF TIMER
ON
OFF SET
COLORSTREAM DVD
SELECT
ADJUST
SET
ENTER
cd ab
3. Press aor b to highlight SET, then press ENTER. The ON/OFF
TIMER menu appears.
4. Press cor dto highlight CLOCK, then press aor bto highlight
the hour position.
Exit
Menu/
Enter
CH
PICTURE AUDIO SETUP OPTION
ON/OFF TIMER
CLOCK
12:00 AM
Note:
ON TIMER
12:00 AM
CH 001
CLEAR
If the power source for the TV is interrupted
(for example, the power cord is unplugged or
a power failure occurs), you will need to reset
the clock.
OFF TIMER
12:00 AM
CLEAR
SELECT
END
ADJUST
EXIT
5. Press cor dto set the hour, then press bto highlight the minute
position.
CH
PICTURE AUDIO SETUP OPTION
ON/OFF TIMER
CLOCK
8:30 AM
ON TIMER
12:00 AM
CH 001
CLEAR
OFF TIMER
12:00 AM
CLEAR
SELECT
END
ADJUST
EXIT
6. Press cor dto set the minutes, then press EXIT to return to
normal viewing.
Setting the ON/OFF timer
Setting the on timer
This feature allows you to program the TV to turn on automatically at a
set time. If you program the ON TIMER to “DAILY,” the TV will turn on
every day at the same time to the same channel until you clear the ON
TIMER.
To set the on timer: (Example: Turning on the TV to channel 12 at
7:00 AM, DAILY)
cd ab
1. Press MENU, then press aor b to display the OPTION menu.
2. Press cor dto highlight ON/OFF TIMER.
3. Press aor b to highlight SET, then press ENTER. The ON/OFF
TIMER menu appears.
4. Press cor dto highlight ON TIMER and press aor b to highlight
the hour position.
Menu/
Enter
Note:
CH
After a power failure or disconnection of the
power, the timer settings will be lost.
PICTURE AUDIO SETUP OPTION
ON/OFF TIMER
CLOCK
12:00 AM
ON TIMER
12:00 AM
CH 001
CLEAR
OFF TIMER
12:00 AM
CLEAR
SELECT
END
ADJUST
EXIT
22
J3S00121A(E)_P14-25
22
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
5.Press cor dto set the desired hour, then press b.
CH
PICTURE AUDIO SETUP OPTION
ON/OFF TIMER
CLOCK
12:00 AM
ON TIMER
7:00 AM
CH 001
CLEAR
OFF TIMER
12:00 AM
CLEAR
SELECT
END
ADJUST
EXIT
6.Set the desired minutes and channel, as in step 5.
7.Press aor b to select ONCE or DAILY timer date.
CH
PICTURE AUDIO SETUP OPTION
ON/OFF TIMER
cd ab
CLOCK
12:00 AM
ON TIMER
7:00 AM
CH 012
ONCE DAILY CLEAR
OFF TIMER
12:00 AM
CLEAR
SELECT
END
SET
ENTER
EXIT
Exit
8.Press EXIT to return to normal viewing.
To cancel the on timer:
Select CLEAR in step 7 above.
Press EXIT to return to normal viewing.
Note:
The ON TIMER has a one-hour automatic
shut off. One hour after the ON TIMER has
turned on the TV, the TV will turn off
Setting the off timer
This feature allows you to program the TV to turn off automatically at a set
time. If you program the OFF TIMER to “DAILY,” the TV will automatically
turn off every day at the same time.
automatically unless you press any button .
To set the off timer: (Example: Turning off the TV at 11:30 PM)
1. Press MENU, then press aor b to display the OPTION menu.
2. Press cor dto highlight ON/OFF TIMER.
3. Press aor b to highlight SET, then press ENTER.
The ON/OFF TIMER menu appears.
4. Press cor dto highlight OFF TIMER, then press aor b to
highlight the hour position.
CH
PICTURE AUDIO SETUP OPTION
ON/OFF TIMER
CLOCK
12:00 AM
ON TIMER
7:00 AM
CH 012
DAILY
OFF TIMER
12:00 AM
cd ab
CLEAR
SELECT
END
ADJUST
EXIT
5. Press cor dto set the desired hour, then press b.
CH
Exit
Menu/
Enter
PICTURE AUDIO SETUP OPTION
ON/OFF TIMER
CLOCK
12:00 AM
ON TIMER
7:00 AM
CH 012
DAILY
OFF TIMER
11:00 PM
CLEAR
SELECT
END
ADJUST
EXIT
6. Set the desired minutes, as in step 5.
7. Press aor b to select ONCE or DAILY.
CH
PICTURE AUDIO SETUP OPTION
ON/OFF TIMER
CLOCK
12:00 AM
ON TIMER
7:00 AM
CH 012
DAILY
OFF TIMER
11:30 PM
ONCE DAILY CLEAR
SELECT
END
SET
ENTER
EXIT
8. Press EXIT to return to normal viewing.
To cancel the off timer:
Select CLEAR in step 7 above.
Press EXIT to return to normal viewing.
23
J3S00121A(E)_P14-25
23
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the picture quality
You can adjust the picture quality to your personal preferences,
including the contrast, brightness, color, tint, and sharpness. The
qualities you choose will be stored automatically in your TV’s memory
so you can recall them at any time.
To adjust the picture quality:
1. Press MENU, then press aor b to display the PICTURE menu.
CH
PICTURE AUDIO SETUP OPTION
CONTRAST
BRIGHTNESS
COLOR
64
32
32
0
TINT
cd ab
SHARPNESS
SELECT
32
ADJUST
2. Press cor duntil the item you want to adjust is highlighted.
3. Press aor b to adjust the level.
Exit
Selection
a
Pressing b
Menu
contrast
brightness
color
tint
sharpness
lower
darker
paler
reddish
softer
higher
lighter
deeper
greenish
sharper
Reset
Note:
To reset the picture adjustments to the factory
settings, press RESET.
4. Press EXIT to return to normal viewing.
To select the input mode:
Watching video input
You can use the TV/VIDEO button on the remote control to view a
signal coming from other devices, such as VCRs or video disc players
that may be connected to your TV. (See “Connecting your TV” on page 7.)
Press the TV/VIDEO button repeatedly to
select the desired mode. The signal source
you are connected to is displayed in light blue.
TV
VIDEO 1
VIDEO 2
Specifying the ColorStream® setting
You can use the ColorStream (component video) input for connecting
either a DVD player or a DTV receiver.
COLOR
STREAM
Note: This TV is not HD ready.
1. Press TV/VIDEO to put the TV in
CH
ColorStream mode.
PICTURE AUDIO SETUP OPTION
LANGUAGE
ENGLISH
2. Press MENU, then press aor buntil
the OPTION menu appears.
3. Press cor dto highlight
COLORSTREAM.
4. Press aor bto highlight DVD or
DTV, depending on which device is
connected.
CH LABEL
FAVORITE CH
V-CHIP
START
START
START
START
OFF
LOCK
ON/OFF TIMER
COLORSTREAM DVD DTV
SELECT
ADJUST
5. Press EXIT to return to normal viewing.
Recall
Note: The factory setting is DVD.
cd ab
Displaying on-screen information
Press RECALL to display the following
(
)
TV
on-screen information:
• Clock
12:00 AM
STEREO
SAP
CABLE 007
ABCD
Exit
• Channel number or VIDEO mode
selected
Menu
• Channel label (if preset)
• Stereo or SAP (second audio program)
audio status
MPAA
X
TV/Video
• Content rating
24
J3S00121A(E)_P14-25
24
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the sleep timer
You can set the TV so it turns off automatically.
To set the sleep timer:
Repeatedly press SLEEP on the remote control to set the length of
time until the TV turns off. The clock will count down 10 minutes for
each press of the SLEEP button (120, 110, ...10, 0). After the sleep
time is programmed, the display will appear briefly every ten minutes
to remind you that the sleep timer is operating.
To confirm the sleep timer setting:
Press SLEEP one time. The remaining time will be momentarily
displayed.
Sleep
To cancel the sleep timer:
Repeatedly press SLEEP until the display turns to 0.
Using the closed caption feature
The closed caption feature has two options: captions or text. A caption
is a printed version of the dialogue, narration and/or sound effects of a
program. Text is information not related to the program that appears on
half of the TV screen when available.
1/2
CAP/TEXT
To view captions or text:
1. Select the desired program. Closed captioned programs are
usually marked in your local TV listing as “CC.”
2. Press CAP/TEXT repeatedly to select caption or text mode.
16:9
16:9
CAPTION CH1
TEXT CH1
Note:
A closed caption signal may not be decoded
in the following situations:
• When a video tape has been dubbed.
• When the signal reception is weak.
• When the signal reception is non-standard.
3. Press 1/2 to select the caption or text channel.
When you select the text mode, the text
screen always appears as a black box. When
there is no signal, however, the text screen
will not display text characters. Repeatedly
press CAP/TEXT until the box disappears.
TEXT CH2
CAPTION CH2
4. To turn off the closed caption feature, press CAP/TEXT
repeatedly until captions or text no longer display on-screen.
Changing the picture size
NOTICE OF POSSIBLE ADVERSE
EFFECTS ON TV PICTURE TUBE
Avoid displaying stationary images on your
TV screen for extended periods of time.
Fixed (non-moving) images (such as black/
gray bars in wide-screen picture formats,
video game patterns, TV station logos,
closed captions) can become permanently
ingrained in the picture tube. This type of
damage is NOT COVERED BY YOUR
WARRANTY.
You can change the picture size to 16:9 (widescreen) style.
To view 16:9 style:
Select the desired program, then press 16:9. The picture size will
be displayed 16:9 style. “16:9” will appear on the screen for approx.
4 seconds.
To cancel 16:9 style:
Press 16:9 again. The picture size will return to 4:3 style.
16:9
16:9 Widescreen
4:3 Normal
25
J3S00121A(E)_P14-25
25
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the sound
Muting the sound
Press MUTE to temporarily turn off the sound. While the sound is off,
the screen will display the word MUTE in the lower right-hand corner.
To restore the sound, press MUTE again.
Selecting stereo/SAP broadcasts
You can listen to high-fidelity stereo sound with the Multi-channel TV
Sound (MTS) feature. MTS can also transmit a second audio program
(SAP) containing a second language or other audio information.
Recall
Mute
When the TV receives a stereo or SAP broadcast, the word STEREO
or SAP appears on-screen every time the TV is turned on, the channel
is changed, or the RECALL button is pressed.
The MTS feature is not available in the VIDEO mode.
You can leave your TV in STEREO mode because it will automatically
output stereo or monaural sound, depending on the broadcast type. If
the stereo sound is noisy, select MONO to reduce the noise. The word
STEREO or SAP is displayed in light blue when the TV receives the
signal.
MTS
To select the desired MTS setting:
Repeatedly press the MTS button to select either STEREO, SAP,
MONO+SAP, or MONO. If the current program is not available in stereo
or SAP, the setting will not be available when you press the MTS
button.
STEREO
MONO
SAP
MONO + SAP
If the current program is not broadcasting either stereo or SAP, those
settings will not be available when you press the MTS button.
26
J3S00121A(E)_P26-BACK
26
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the sound quality
You can change the sound quality of your TV by adjusting the bass,
treble, and balance.
To adjust the sound quality:
1. Press MENU, then press aor buntil the AUDIO menu appears.
CH
PICTURE AUDIO SETUP OPTION
BASS
32
32
0
TREBLE
BALANCE
SURROUND
OFF
STABLE SOUND OFF
c d a b
SELECT ADJUST
2. Press cor dto highlight the item you want to adjust.
3. Press aor bto adjust the level.
Menu
Reset
CH
PICTURE AUDIO SETUP OPTION
BASS
32
32
0
TREBLE
BALANCE
SURROUND
Note:
OFF
To reset the audio adjustments to the factory
settings, press RESET.
STABLE SOUND OFF
SELECT ADJUST
• amakes the sound quality weaker or decreases the balance in
the right channel, depending on the item selected.
• bmakes the sound quality stronger or decreases the balance in
the left channel, depending on the item selected.
Using the surround sound feature
The surround sound feature expands the audio listening field wider and
deeper to create exceptional sound quality from the TV’s speakers.
The feature uses stereo signals from a TV broadcast or video input.
To turn on the surround sound feature:
1. Select the STEREO mode, if available (see “Selecting stereo/SAP
broadcasts” on page 26.)
2. Press MENU, and then press aor buntil the AUDIO menu
appears.
3. Press cor dto highlight SURROUND.
4. Press aor bto highlight ON.
c d a b
CH
PICTURE AUDIO SETUP OPTION
BASS
TREBLE
BALANCE
32
32
0
OFF
SURROUND
ON
STABLE SOUND OFF
Menu
SELECT ADJUST
To turn off the surround sound feature:
Highlight OFF in step 4 above.
16:9
In general, you can leave your TV in surround mode because it will
automatically output the type of sound being broadcast (surround
stereo or monaural).
27
J3S00121A(E)_P26-BACK
27
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the StableSound® feature
The StableSoundfeature limits the highest volume level to prevent
extreme changes in volume when the signal source is changed.
To turn on the StableSound® feature:
1. Press MENU, then press aor buntil the AUDIO menu appears.
2. Press cor dto highlight STABLE SOUND.
3. Press aor bto highlight ON.
CH
PICTURE AUDIO SETUP OPTION
BASS
32
32
0
TREBLE
BALANCE
SURROUND
c d a b
OFF
STABLE SOUND ON OFF
SELECT ADJUST
To turn off the StableSound® feature:
Highlight OFF in step 3 above.
Menu
Auto power off
The TV will automatically turn off after approximately 15 minutes if it is tuned to a vacant channel or a station that completes its
broadcast for the day and stops broadcasting on that channel. This feature does not work in VIDEO mode.
Understanding the Power Return feature
If the power is cut off while you are viewing the TV and the power is resupplied, the Power Return feature will turn the TV
on automatically.
If the power is going to be off for a long time or you are going to be away from home for a long time, unplug the power cord
from the wall outlet to prevent the TV from turning on in your absence.
28
J3S00121A(E)_P26-BACK
28
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
Before calling a service technician, please check the following table for a possible cause of the problem and some solutions.
Problem
Solution
TV will not turn on
• Make sure the power cord is plugged in, then press POWER.
• The remote control batteries may be dead. Replace the batteries.
No picture, no sound
• Check the antenna/cable connections.
• This TV will not accept or display 480p or 720p progressive scan
signals or 1080i interlaced high-definition signals through its
ColorStream inputs. Switch the other device’s output to 480i interlaced
mode first (see page 9).
No sound, picture OK
• The sound may be muted. Press VOLUME.
• The station may have broadcast difficulties. Try another channel.
• The MTS feature may be in SAP mode. Press the MTS button on the
remote control until STEREO (or MONO) mode is active.
Poor sound, picture OK
Poor picture, sound OK
• The station may have broadcast difficulties. Try another channel.
• The MTS feature may be in SAP mode. Press the MTS button on the
remote control until STEREO (or MONO) mode is active.
• Check the antenna connections.
• The station may have broadcast difficulties. Try another channel.
• Adjust the PICTURE menu.
• This TV will not accept or display 480p or 720p progressive scan
signals or 1080i interlaced high-definition signals through its
ColorStream inputs. Switch the other device’s output to 480i interlaced
mode first (see page 9).
Poor reception of broadcast channels
• The station may have broadcast difficulties. Try another channel.
• Check the antenna connections.
• If you are using a VCR, make sure the TV/VCR button is set correctly.
Cannot receive above channel 13
Unable to select a certain channel
•
Make sure the TV/CABLE feature in the SETUP menu is set to “CABLE”.
• The channel may be blocked by the V-Chip feature or CH LOCK
feature, or erased with the add/erase feature.
Cannot access signal input sources
(Video1,Video2 and ColorStream)
and/or Channels 3 and 4
• Check the VIDEO LOCK feature.
Multiple images
• The station may have broadcast difficulties. Try another channel.
• Use a highly directional outdoor antenna.
Poor color or no color
• The station may have broadcast difficulties. Try another channel.
• Adjust the TINT and/or COLOR in the PICTURE menu.
• If you change the direction of the TV while it is turned on, the picture
could suffer from color shading. If so, turn off the TV and allow it to cool
for several hours before turning it on again.
Black box on screen
• Repeatedly press CAP/TEXT to turn off the Closed Caption Text mode.
No stereo or SAP sound from a
known MTS broadcast
• Make sure the MTS feature is set properly.
The V-Chip PIN code does not work
(U.S. V-Chip system only)
• Change or reset your PIN code (pages 15 and 16).
The remote control does not operate
• Remove all obstructions between the remote control and the TV.
• The remote control batteries may be dead. Replace the batteries.
29
J3S00121A(E)_P26-BACK
29
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
• This model complies with the specifications below.
• Design and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added in the future.
14AF45
20AF45
Picture Tube
14 in. (357 mm) diagonal
(Screen size is approximate.)
NTSC standard
20 in. (508 mm) diagonal
(Screen size is approximate.)
Television system
Channel coverage
VHF: 2–13
UHF: 14–69
Cable TV: 4A, A-5–A-1, A-I,
+
+
J–W, W 1–W 84
Power source
120V AC, 60 Hz
Power consumption
Audio power
80 W
105 W
2.5 W + 2.5 W
Speaker type
1-5/8 in. x 2-13/16 in. x 2 pcs.
S-VIDEO INPUT
2 in. x 4-11/16 in. x 2 pcs.
Video/Audio terminals
Y-INPUT: 1V (p-p), 75 ohm, negative sync.
C-INPUT: 0.286V (p-p) (burst signal), 75 ohm
VIDEO/AUDIO INPUT
VIDEO: 1V (p-p), 75 ohm, negative sync.
AUDIO: 150 mV (rms) (30% modulation equivalent, 47k ohm)
ColorStream® (component video) INPUT
Y : 1V (p-p), 75 ohm
PR : 0.7V (p-p), 75 ohm
PB : 0.7V (p-p), 75 ohm
Dimensions
Width:
Height:
Depth:
17 in. (432 mm)
23-1/4 in. (590 mm)
17-9/16 in. (446.5 mm)
19-1/16 in. (484 mm)
13-9/16 in. (344.5 mm)
15-3/16 in. (386 mm)
Weight
24.3 lbs. (11 kg)
50.6 Ibs. (23 kg)
Supplied accessories
Remote control with two size “AAA” batteries
30
J3S00121A(E)_P26-BACK
30
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited United States Warranty
For 24'' FST PURE® and All Smaller Television Models
Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following
(3) Warranties from TACP are effective only if the television is purchased
and operated in the U.S.A. or Puerto Rico.
limited warranties to original consumers in the United States. THESE
LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER
PURCHASER OR ANY PERSON RECEIVING THIS TELEVISION AS A
GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO
OTHER PURCHASER OR TRANSFEREE.
PRODUCTS PURCHASED IN THE U.S.A. AND USED ANYWHERE
OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA
AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.
PRODUCTS PURCHASED ANYWHERE OUTSIDE OF THE U.S.A.,
INCLUDING, WITHOUT LIMITATION, CANADAAND MEXICO, AND USED
IN THE U.S.A., ARE NOT COVERED BY THESE WARRANTIES.
(4) Labor service charges for set installation, setup, adjustment of
customer controls and installation or repair of antenna systems are
not covered by these warranties. Reception problems caused by
inadequate antenna systems are your responsibility.
(5) Warranties extend only to defects in materials or workmanship as
limited above and do not extend to any television or parts which
have been lost or discarded by you or to damage to television or
parts caused by fires, misuse, accident, Acts of God, such as
lightning or fluctuations in electric power, improper installation,
improper maintenance or use in violation of instructions furnished by
TACP; or to units which have been modified or had the serial number
removed, altered, defaced or rendered illegible.
Limited Ninety (90) Day Warranty on Labor*
TACP warrants this television and its parts against defects in materials or
workmanship for a period of ninety (90) days after the date of original retail
purchase. DURING THIS PERIOD, TACP WILL, AT TACP’S OPTION,
REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR REFUR-
BISHED PART WITHOUT CHARGE TO YOU FOR PARTS OR LABOR.
YOU MUST DELIVER THE ENTIRE TELEVISION TO AN AUTHORIZED
TACP SERVICE STATION. YOU MUST PAY FOR ALL TRANSPORTATION
AND INSURANCE CHARGES FOR THE TELEVISION TO AND FROM
THE SERVICE STATION.
How to Obtain Warranty Services
If, after following all of the operating instructions in this manual and checking
the section “Troubleshooting”, you find that service is needed:
(1) To find the nearest TACP Authorized Service Station, visit TACP’s
(2) You must deliver the entire television to a TACP Authorized Service
Station and present your bill of sale or other proof of purchase. You
must pay for all transportation and insurance charges for the
television to and from the Service Station.
Limited One (1) Year Warranty on Parts*
TACP further warrants the parts in this television against defects in
materials or workmanship for a period of one (1) year after the date of
original retail purchase. DURING THIS PERIOD, TACP WILL, AT TACP’S
OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR
REFURBISHED PART WITHOUT CHARGE TO YOU FOR THE PART,
PROVIDED THAT IF A DEFECTIVE PART IS REPAIRED OR REPLACED
AFTER NINETY (90) DAYS FROM THE DATE OF ORIGINAL RETAIL
PURCHASE, YOU MUST PAY ALL LABOR CHARGES INVOLVED IN THE
REPAIR OR REPLACEMENT. YOU MUST DELIVER THE ENTIRE
TELEVISION TO AN AUTHORIZED TACP SERVICE STATION. YOU
MUST PAY FOR ALL TRANSPORTATION AND INSURANCE CHARGES
FOR THE TELEVISION TO AND FROM THE SERVICE STATION.
For additional information, visit TACP’s web site:
ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE
U.S.A., INCLUDING THE IMPLIED WARRANTIES OF
Limited Two (2) Year Warranty on Picture Tube*
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED
WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY
WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE U.S.A. AS
HEREBY LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE AND
IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES, AGREEMENTS,
AND SIMILAR OBLIGATIONS OF TACP WITH RESPECT TO THE
REPAIR OR REPLACEMENT OF ANY PARTS. IN NO EVENT SHALL
TACP BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, BUSINESS
INTERRUPTION, OR MODIFICATION OR ERASURE OF RECORDED
DATA CAUSED BY USE, MISUSE OR INABILITY TO USE THIS
PRODUCT).
TACP further warrants the picture tube in this television against defects in
materials or workmanship for a period of two (2) years after the date of
original retail purchase. DURING THIS PERIOD, TACP WILL, AT TACP’S
OPTION, REPAIR OR REPLACE A DEFECTIVE PICTURE TUBE WITH A
NEW OR REFURBISHED PICTURE TUBE WITHOUT CHARGE TO YOU,
EXCEPT THAT IF A DEFECTIVE PICTURE TUBE IS REPAIRED OR
REPLACED AFTER NINETY (90) DAYS FROM THE DATE OF THE
ORIGINAL RETAIL PURCHASE, YOU MUST PAY ALL LABOR CHARGES
INVOLVED IN THE REPAIR OR REPLACEMENT. YOU MUST DELIVER
THE ENTIRE TELEVISION TO AN AUTHORIZED TACP SERVICE
STATION. YOU MUST PAY FOR ALL TRANSPORTATION AND INSUR-
ANCE CHARGES FOR THE TELEVISION TO AND FROM THE SERVICE
STATION.
Rental Units
The warranty for rental units begins with the first rental or thirty (30) days
from the date of shipment to the rental firm, whichever comes first.
No person, agent, distributor, dealer or company is authorized to change,
modify or extend the terms of these warranties in any manner whatsoever.
The time within which action must be commenced to enforce any obligation
of TACP arising under this warranty or under any law of the United States
or of any state thereof is hereby limited to 90 days from the date you
discover or should have discovered, the defect. This limitation does not
apply to implied warranties arising under the law of any state of the U.S.A.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO
STATE IN THE U.S.A. SOME STATES OF THE U.S.A. DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, WHEN
AN ACTION MAY BE BROUGHT, OR THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU UNDER
SUCH CIRCUMSTANCES.
*Commercial Units
Televisions sold and used for commercial purposes have a limited ninety
(90) day warranty for all parts, labor and picture tube.
Owner’s Manual and Product Registration Card
Read this owner’s manual thoroughly before operating this television.
Complete and mail the enclosed product registration card or register your
registering your product you will enable TACP to bring you new products
specifically designed to meet your needs and help us to contact you in the
unlikely event a safety notification is required under the Consumer Product
Safety Act. Failure to complete and return the product registration card
does not diminish your warranty rights.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING
CONDITIONS:
(1) You must provide your bill of sale or other proof of purchase.
(2) All warranty servicing of this television must be made by an
Authorized TACP Service Station.
FST PURE® is a registered trademark of Toshiba America Consumer
Products, L.L.C.
31
J3S00121A(E)_P26-BACK
31
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
National Service Division
ColorStream®, FST Pure® and StableSound® are registered
trademarks of Toshiba America Consumer Products, L.L.C.
GameTimer is a trademark of Toshiba America Consumer Products, L.L.C.
PRINTED IN THAILAND
J3S00121A(E)_P26-BACK
32
13/01/2005, 5:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
|