Blu-ray Disc Player
BDX3000KU
OWNER’S MANUAL
Owner’s Record
The model number and serial number are on the back of the
unit. Record these numbers in the spaces below. Refer to
these numbers whenever you communicate with your Toshiba
dealer about this unit.
Model number:
Serial number :
© 2010 Toshiba Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
CAUTION:
•
•
•
To prevent direct exposure to laser beam, do not try to open the enclosure.Visible and invisible laser radiation when open and
interlocks defeated. DO NOT STARE INTO BEAM.
Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation
exposure.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Warning: Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
The party responsible for compliance to these rules is:
Toshiba America Consumer Products, L.L.C.
82 Totowa Rd. Wayne, NJ 07470.
Ph: 1-800-631-3811
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
-
-
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
WARNING: Changes or modifications to this unit not expressly approved by Toshiba, or parties authorized by Toshiba, could void
the user’s authority to operate the equipment.
Notes On Copyright
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized by Rovi Corporation, and is intended for home and other limited
viewing uses only unless otherwise authorized by Rovi Corporation. Reverse engineering or disassembly is prohibited.
On Placement
•
•
Do not use this unit in places which are extremely hot, cold, dusty or humid.
Do not restrict the air flow of this unit by placing it somewhere with poor air flow, by covering it with a cloth, or by placing it on
bedding or carpeting.
•
Be sure to remove the disc and unplug the AC power cord from the outlet before carrying the unit.
On Safety
• Do not handle the AC power cord with wet hands and do not put your fingers or objects into the unit.
• When connecting or disconnecting the AC power cord, grip the plug and not the cord itself. Pulling the cord may damage it
and create a hazard.
• When you are not going to use the unit for a long period of time, disconnect the AC power cord.
On Condensation
• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the equipment.
When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1-2 hours before turning
the power on or gradually heat the room and allow the unit to dry before use.
On Recycling
• This unit’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
• Batteries should never be thrown away or incinerated but disposed of in accordance with your local
regulations concerning chemical wastes.
Products that earn the ENERGY STAR® prevent greenhouse gas emissions by meeting strict energy efficiency
guidelines set by the U.S. Environmental Protection Agency and the U.S. Department of Energy. ENERGY STAR and
the ENERGY STAR mark are registered U.S. marks.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
“Wi-Fi CERTIFIED” logo is
a registered trademark of
Wi-Fi Alliance. “Wi-Fi PRO-
TECTED SETUP” logo is a
trademark of Wi-Fi Alliance.
Supplied Accessories
BONUSVIEW
“DVD” logo is a trademark
of DVD Format / Logo
Licensing Corporation.
HDMI, the HDMI logo, and
High-Definition Multimedia
Interface are trademarks
or registered trademarks
of HDMI Licensing LLC in
the United States and other
countries.
Remote Control with
Batteries (AAA x 2)
Composite Audio / Video
Cables
OWNER’S MANUAL
Manufactured under license
from Dolby Laboratories.
Dolby and the double-D
symbol are trademarks of
Dolby Laboratories.
Owner’s Manual
(EN)
Quick Start Guide
(EN/ES)
Manufactured under license
under U.S. Patent #’s:
5,451,942; 5,956,674;
5,974,380; 5,978,762;
6,226,616; 6,487,535;
7,392,195; 7,272,567;
7,333,929; 7,212,872 &
other U.S. and worldwide
patents issued & pending.
DTS and the Symbol are
registered trademarks, &
DTS-HD, DTS-HD Master
Audio | Essential and the
DTS logos are trademarks
of DTS, Inc. Product
Symbols Used in this Manual
To specify for which media type each function is, we put the
following symbols at the beginning of each item to operate.
Symbol
Description
Description refers to BD-video and BD-RE
/ BD-R recorded in BDMV format
Description refers to DVD-video
includes software. © DTS,
Inc. All Rights Reserved.
Description refers to Audio CD / DTS-CD
“x.v.Color” and “x.v.Color”
logo are trademarks of Sony
Corporation.
Description refers to DVD-RW/-R with
AVCHD files
Description refers to BD-RE/-R, DVD-
RW/-R, CD-RW/-R and SD Memory Card
with MP3 files
“AVCHD” and the “AVCHD”
logo are trademarks of
Panasonic Corporation and
Sony Corporation.
Description refers to BD-RE/-R, DVD-
RW/-R, CD-RW/-R and SD Memory Card
with Windows Media™ Audio files
“BONUSVIEW™”, “BD-
LIVE™” and “Blu-ray 3D™”
are trademarks of Blu-ray
Disc Association.
Description refers to BD-RE/-R, DVD-
RW/-R, CD-RW/-R and SD Memory Card
with JPEG files
If you do not find any of the symbols listed above under the
function heading, the operation is applicable to all media.
Oracle and Java are
registered trademarks
of Oracle and/or its
affiliates. Other names
may be trademarks of their
respective owners.
Trademark Information
Windows Media and the
Windows logo are
“Blu-ray Disc™” and
Association.
Blockbuster is a registered trademark of Blockbuster, Inc.
Netflix is a registered trademark of Netflix Inc.
Pandora is a registered trademark of Pandora Media, Inc.
VUDU is a trademark of VUDU, Inc.
are trademarks of Blu-ray Disc
trademarks or registered
trademarks of Microsoft
Corporation in the United
States and/or other
countries.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction
Accessing a Specific Location Directly.......... 21
Locating a specific title/chapter/time ......................... 21
SAFETY PRECAUTIONS .....................................2
IMPORTANT SAFETY INSTRUCTIONS ............. 2
PRECAUTIONS ................................................... 3
Supplied Accessories ....................................... 4
Symbols Used in this Manual ........................... 4
Trademark Information ...................................... 4
Table of Contents ............................................... 5
Features .............................................................. 6
Repeating a Title, Chapter,Track or Specific
Segment ............................................................ 22
Repeating a title, chapter or track .............................. 22
Repeating a specific segment ................................... 22
Playing in a Random Order.............................. 22
Playing tracks or files in a random order ................... 22
PIP(BONUSVIEW) Setting................................ 23
Camera Angle ................................................... 23
Audio Selection................................................. 23
Subtitle Selection ............................................. 24
Displaying On-screen Information.................. 24
Identification of Controls .................................. 7
Front panel.................................................................... 7
Rear panel..................................................................... 7
Using the Remote Control ................................ 8
Remote Control............................................................. 8
Installing batteries......................................................... 9
Operating with the remote control............................... 10
Front Panel Display ..................................................... 10
Playing AVCHD/MP3/WMA/JPEG Files ............25
Playing files on a data disc......................................... 25
Using an SD Card ..............................................26
Inserting an SD card ................................................. 26
Using a USB Device ..........................................27
Operating a USB device ............................................ 27
Connections
Connecting to a TV .......................................... 11
Connecting to a TV using an HDMI cable ................... 12
Connecting to a TV using a component video cable... 12
Connecting to a TV using an A/V cable....................... 12
Customizing the Function Settings
General Operations ...........................................28
Info Menu............................................................28
Performing Quick-Setup ...................................28
Using BD-LiveTM Features ................................28
Display Setting...................................................29
Audio Setting .....................................................31
Speaker Setting .................................................32
Language Setting ..............................................33
Parental Control.................................................33
System Setting...................................................34
UpgradingYour Player’s Firmware ..................35
Network Connection Setting ............................36
Connecting to an Audio System .....................13
Via 2-Channel Analog Audio Output ........................... 13
Via Digital Audio Output .............................................. 13
Via HDMI Audio Output ............................................... 13
Network Connection .........................................14
Connecting your player to a wired router .................... 14
Connecting your player to a wireless access point or
router........................................................................... 14
Connecting the Speakers .................................15
Positioning the Speakers..................................16
Playback
Using the Connected Applications .................39
Watching Movies with Netflix® .................................... 39
Watching Movies with BLOCKBUSTER® ................... 40
Watching Movies with VUDU™ ................................... 40
Listening to Music with PANDORA® ........................... 41
Information on Playback.................................. 17
Playable Discs and Files ............................................ 17
Unplayable Discs and Files........................................ 17
Color Systems............................................................ 18
Region Codes ............................................................ 18
Structure of Disc/SD Card Contents .......................... 18
Others
Playing a Disc ................................................... 19
Troubleshooting & Maintenance ......................42
Troubleshooting........................................................... 42
Maintenance .............................................................. 43
Basic playback ........................................................... 19
Variable Speed Playback.................................. 20
Playing in fast reverse / forward directions................. 20
Playing frame by frame .............................................. 20
Playing in slow motion ............................................... 20
Glossary .............................................................44
Specifications ....................................................46
Limited Warranty................................................47
Locating a Desired Section ............................. 20
Locating a title using the top menu ............................ 20
Locating a specific chapter or track............................ 21
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Features
Blu-ray Disc
x.v.Color
You can enjoy Blu-ray Disc which is capable of storing five times
more data than a conventional DVD.
This unit supports playback of video contents on discs recorded
with “x.v.Color” technology. To watch this video content with
the “x.v.Color”, a TV or other display device supporting both
video image reproduction using the “x.v.Color” standard and
capable of manually switching it’s color setting is required.
Please refer to the owner’s manual of your display device for
further information.
BD-Java
With some BDs which support Java applications, you can enjoy
the interactive functions such as games or interactive menus.
BD-Live
BD-Live (BD-ROM version 2 Profile 2.0) that allows interactive
functions to be used when this unit is connected to the Internet
in addition to the BONUSVIEW function.The various functions
differ depending on the disc.
Wi-Fi CERTIFIED
The Wi-Fi CERTIFIED logo is an assurance that Wi-Fi Alliance
has tested a product in numerous configurations and with a
diverse sampling of other devices to ensure compatibility with
other Wi-Fi CERTIFIED equipment that operates in the same
frequency band.
Full high-definition video playback
Watch movies in the highest picture quality available for your
HDTV. This unit offers full high-definition video playback up to
1080p resolution for an amazing viewing experience. A highly
detailed picture and increased sharpness delivers a more true-
to-life picture.
Blu-ray 3D Feature
This product can play 3D contents through an HDMI cable.
To implement the 3D effect, connect a 3D device (3D-compliant
AV receiver, 3D-compliant TV) to the product using an HDMI
cable, and play the 3D content while wearing 3D vision
glasses.
DVD Upconversion for enhanced picture quality
Your current DVD will look even better than before thanks to
video upconversion. Upconversion will increase the resolution
of standard definition DVD to high definition up to 1080p over
an HDMI connection. The picture will be less jagged and more
realistic for a near high-definition experience.
Easy and simple connection to your HDTV via HDMI
Connect this unit to your HDTV with one single HDMI (High-
Definition Multimedia Interface) cable. It is recommended to
use a High Speed HDMI Cable for better compatibility.The high
definition video output signal will be transferred to your HDTV
without conversion to analog signals, so you will get excellent
picture and sound quality.
Enjoy your content on different kinds of media
Full backwards compatibility with BD, DVD, CD and SD card
ensures that you can continue to enjoy your current audio-video
collection. Additionally, you can view JPEG digital pictures or
listen to MP3 or Windows Media™ Audio music files.
Experience rich multi-channel surround sound
Multi-channel surround sound, which recognizes real-to-life
sound and makes you feel like you are really there.
Thanks to other multiple outputs, you can also easily connect
to your home theater system or amplifier.
HDMI CEC (Consumer Electronics Control)
This unit supports HDMI CEC, which allows integrated system
control over HDMI and is part of the HDMI standard.
PIP (BONUSVIEW)
Some BD-videos have the PIP function which enables you to
display the secondary video in the primary video.You can call
up the secondary video by pressing BONUSVIEW whenever
the scene contains the secondary video.
This function may not work properly on some devices.
HDMI 1080p/24F output (BD only)
This unit is equipped with a feature which can provide the
smooth movement in the playback of film originated material
with the frame rate of 24 frames per second with progressive
scan. (Available only when the TV is connected by an HDMI
cable and compatible with 1080p/24F frame input.)
Pop-up menu
Some BD-video have pop-up menu which is a navigation menu
that can be called up and be operated on theTV screen without
interrupting the playback.You can call up the pop-up menu by
pressing POPUP/TOP MENU or MENU.Contents in the pop-up
menu vary depending on the disc.
Refer to “Display Setting” in “Customizing the Function
Settingss” on page 29.
Playback of Content from an SD Memory Card
Copyright protection system
You can play back MP3 / WMA / JPEG files stored in an SD
Memory Card. You can store picture-in-picture commentary,
subtitles or other extras for BD-ROM ver. 2 (Profile 2.0 / Profile
1.1) files in an SD Memory Card and play back with the BD-
video.
To play back the digital video images of a BD / DVD via an HDMI
connection, it is necessary that both the unit and the TV (or an
AV amplifier) support a copyright protection system called HDCP
(high-bandwidth digital content protection system). HDCP is
copy protection technology that comprises data encryption and
authentication of the connected AV device. This unit supports
HDCP. Please read the operating instructions of your TV (or AV
amplifier) for more information.
Playing back AVCHD files
This unit supports playback of AVCHD format files (new format
for high definition video camcorders) recorded on disc.Your high
definition personal archive is playable in HD quality.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification of Controls
Front panel
1
2
3
4* 5* 6* 7*
8
(*) Notes:
1. These indicators are located in the sensor field.
7. ON/STANDBY indicator
2. When this unit is off, these indicators are dimmed. If a fin-
ger is brought close to the sensor field, the indicators will
be invoked and light up.
•
When invoked (white), tap to turn on the unit, or to turn
the unit into the standby mode. (To completely turn off
the unit, you must unplug the AC power cord.)
1. Disc tray
8. SD card slot
2. Remote sensor
3. Display
How to Power OnYour Unit ?
•
Refer to “Front Panel Display” on page 10.
4. OPEN/CLOSE indicator
When invoked (white), tap to open/close the disc tray.
5. STOP indicator
1. Connect to a standard AC outlet to supply power to this
unit, the ON/STANDBY indicator lights in red and then
turns white at once.
•
2. After about 10 seconds, the ON/STANDBY indicator will
turn red automatically.
•
When invoked (white), tap to stop playback.
3. Touch the ON/STANDBY button to turn on the unit. The
ON/STANDBY indicator will remain white (ON mode).
6. PLAY
indicator
•
When invoked (white), tap to start playback.
Rear panel
1
2
3
4
5
6
COMPONENT VIDEO OUTPUT
SBL
SBR
C
SL
SR
FL
FR
Y
PB
PR
AC IN
SW
BITSTREAM
/
PCM
R
AUDLIO
VIDEO
OUTPUT
ANALOG
HDMI OUT
OPTICAL
MULTI CHANNEL AUDIO OUTPUT
LAN
USB
OUTPUT
7
8
9
1. AC power cord
5. COMPONENT VIDEO OUT jacks
•
Connect to a standard AC outlet to supply power to this
unit.
•
Use to connect a TV with component video inputs using
a component video cable.
•
Unplug this cord from the AC outlet to completely turn
off the unit.
6. MULTI CHANNEL AUDIO OUTPUT jacks
•
Use to connect an AV receiver / amplifier with a audio
cable.
2. LAN terminal
•
Use to connect a network equipment with LAN cable.
7. USB jack
•
Use to connect USB flash drives (not included).
3. HDMI OUT jack
•
Use to connect a TV with an HDMI compatible port via
an HDMI cable.
4. OPTICAL jack
Use to connect an AV receiver / amplifier, Dolby Digital /
8. AUDIO OUT jacks
•
Use to connect a TV, an AV receiver / amplifier or other
device with a composite audio cable.
•
9. VIDEO OUT jack
Use to connect a TV, an AV receiver or other device with
a composite video cable.
DTS decoder or other device with a digital audio optical
input jack using a digital audio optical cable.
•
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Using the Remote control
Remote control
No. Item
Description
Press to adjust aspect ratio in full
stop mode.
1
2
3
ASPECT
15
16
17
18
OPEN/CLOSE
SETTING
Press to open or close the disc tray.
1
2
3
Press to display the settings in
home menu.
Press to display the Connected in
home menu.
4
HOME MENU
19
20
21
Press to switch picture-in-picture
feature on or off (only applicable
to BD-video which supports the
PIP function). For more details,
see “PIP (BONUSVIEW) Setting”
on page 23.
4
5
BONUSVIEW
BONUSVIEW
5
Same as SKIP
For detailed operations, please
refer to SKIP / SKIP
/ SKIP
.
/
22
.
6
7
Press to select a viewing angle if
multiple angles are available on
the disc.
ANGLE
6
7
VOLUME + / -
AUDIO
Press to adjust the volume.
23
Press to select the audio mode.
Press to display the subtitle menu.
SUBTITLE
8
9
24
25
26
27
28
Press to return to the previous
menu.
RETURN
10
Press to adjust the brightness of
display on the front of the Blu-ray
disc player.
DIMMER
11
12
• Press to select items on some
BD contents.
• When file list / thumbnail list is
shown, press to switch between
pages.
29
30
31
RED / GREEN /
BLUE /YELLOW
8
9
13
14
During playback, press to fast
reverse the playback.
REV
32
33
•
During playback, press once to
return to the beginning of the
current title, chapter, track or file.
• During playback, press twice
to return to the previous title,
chapter, track or file.
10 SKIP
•
During the JPEG playback, press
to return to the previous file.
• Press to pause playback.
•
Whenplaybackisinpausemode,
press repeatedly to forward the
playback step by step.
11
12
PAUSE
Press to advance one frame.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
• In playback mode, press GOTO,
then press the number buttons
to enter a title, chapter, track,
time or file number.
• In menu mode, press to enter
the parental code password.
Installing batteries
13 Number buttons
Install the batteries (AAAx2) matching the polarity indicated
inside battery compartment of the remote control.
Press to display the search
menu.
14 GOTO
Open the cover.
1
Press to turn on the unit, or to turn
the unit into the standby mode. (To
completely turn off the unit, you
must unplug the power cord.)
15 ON/STANDBY
• During Blu-ray Disc playback,
press to open
a
menu that
lets you control Blu-ray Disc
playback.
16 POPUP/TOP MENU
• During DVD playback, press
to open the DVD menu (if
available).
Insert batteries.
In playback mode, press to adjust
picture quality according to your
preference (Actual effect to picture
may vary depending on TV.):
• E.P.M (Enhanced Picture Mode):
The picture is sharper with
enhanced color.
2
17 PIC
• Sharpness
18 INFO
Press to display disc information.
Presstoselectthevideoresolution
in full stop mode.
19 RESOLUTION
Make sure to match the + and – on the batteries to the
marks indicated in the battery compartment.
Press to return to the previous
menu.
20 MENU
In PIP mode, press to turn the
audio for the secondary video on
or off. For more details, see “PIP
(BONUSVIEW) Setting” on page
23.
Close the cover.
21 2nd AUDIO
3
/
/
/
Press to select items or settings.
22
Press to confirm or select menu
items.
OK
In PIP mode, press to turn the
subtitle for the secondary video
on or off.
23 2nd SUBTITLE
During playback, press to fast
forward the playback.
24 FWD
Caution: Never throw batteries into a fire.
Press to start playback or resume
playback.
25
PLAY
Notes:
•
During playback, press to skip to
the next title, chapter, track or file.
• Do not mix different battery types or combine used batteries
with new ones.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace both batteries
with new ones.
26 SKIP
• During the JPEG playback,
press to go to the next file.
27 STOP
Press to stop playback.
Press to play back the disc in slow
motion.
• If the batteries are dead or if you will not be using the remote
control for a long time, remove the batteries to prevent battery
acid from leaking into the battery compartment.
28
Press to toggle between various
repeat modes.
29 REPEAT
Press to turn random function on
or off.
30 RANDOM
Press to play back
a
defined
31 A-B
section between point A and B
repeatedly.
32 CLEAR
Press to clear an input error.
Press to confirm or select menu
items.
33 ENTER
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Operating with the remote control
* Do not expose the remote sensor of the Blu-ray disc player
to a strong light source such as direct sunlight or other
illumination. If you do so, you may not be able to operate
the Blu-ray disc player via the remote control.
Point the remote control at the remote
sensor and press the buttons.
Notes:
• Direct the remote control at the remote sensor of the Blu-ray
disc player.
• When using the remote control, press the buttons at intervals
of about 1 second to ensure the correct mode of operation.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot or humid
place.
• Do not spill water or put anything wet on the remote control.
• Do not open the remote control.
Distance:
About 5 m from the
front of the remote
sensor.
Angle:
• If the remote control is not going to be used for a long time,
remove the battery to avoid damage caused by battery leakage
corrosion.
About 30° in each
direction of the front of
the remote sensor.
Front Panel Display
1
2
3
4
5
6
7
8
DVD
TRK 2 c h
MULTI
HDMI
CD
9
1080ip
720p
10
480ip
11
1. PLAY indicator
Lights when playing.
2. PAUSE indicator
Lights when paused.
10. Resolution indicator
Shows resolution of video output.
11. Character indicators
Displays various kinds of information such as elapsed time
or message, etc. (See Example shown as below.)
3. DVD indicator
Lights when a DVD disc is inserted.
4. CD indicator
Indicates the
elapsed time
Lights when a CD disc is inserted.
5. TRK (TRACK) indicator
Lights when a CD/MP3 disc is inserted.
Closing the
disc tray
6. Audio Channel indicator
Shows the audio channel of the current DVD/BD.
Indicates that a
Blu-ray disc is
inserted
7. HDMI indicator
Lights when HDMI TV is connected.
8.
9.
(REPEAT) indicator
Illuminates when REPEAT is pressed.
Loading a disc
/
SKIP indicator
Lights while in fast forward / fast reverse mode.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a TV
Connect the Blu-ray player to your TV.
1. Choose the appropriate connection, then proceed to the corresponding instruction (A, B or C) on the
next page.
Best
(Supports up to 1080i/1080p, 1080p/24F resolution.)
Your TV
HDMI IN
Go To
High
Definition
TV
HDMI cable
Video
Audio
A
No analog audio connection required.
• To enjoy the viewing of 3D content, HDMI connection with High Speed HDMI cable must be required.
HDMI Cable NOT INCLUDED
Better
(Supports up to 1080i resolution.)
COMPONENT
VIDEO IN
Y
P
P
B/CB
R/CR
Your TV
component video cable
Video
Go To
High
Definition
TV
B
C
+
L
composite audio cable
Audio
AUDIO IN
R
Component Video Cable NOT INCLUDED
Basic
(Supports only 480i resolution.)
VIDEO IN
Your TV
Video
Go To
Standard
Definition
TV
L
composite audio video cable
+
Audio
AUDIO IN
R
• Connect this unit directly to the TV. If the composite audio / video cables are connected to a VCR, pictures may be
distorted due to the copyright protection system.
Composite Video / Audio Cables INCLUDED
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
2. Connect the cables by following the illustrations below.
Connecting to a TV using an HDMI cable (Best)
Your TV
COMPONENT VIDEO OUT
SBL
C
SL
FL
FR
Y
P
B
PR
AC IN
SBR
SW
SR
R
L
BITSTREAM
/
PCM
VIDEO
OUT
LAN
USB
HDMI OUT
OPTICAL
AUDIO OUT
MULTI CHANNEL AUDIO OUTPUT
A
HDMIcable
HDMI IN
HDMI OUT
Notes:
• Do not tilt the connector when inserting it into the HDMI jack, and make sure the shapes of the jack and the connector
are matched.
• When using non-HDCP compatible TV, the image will not display properly.
• An HDMI cable carries both video and audio signals. If you want to use TV speakers, you do not need to make an
additional audio connection if you are using an HDMI cable.
Connecting to a TV using a component video cable (Better)
Your TV
COMPONENT VIDEO OUT
SBL
C
SL
FL
Y
P
B
PR
AC IN
SBR
SW
SR
FR
R
L
BITSTREAM
/
PCM
VIDEO
OUT
MULTI CHANNEL AUDIO OUTPUT
LAN
USB
HDMI OUT
OPTICAL
AUDIO OUT
B
COMPONENT
VIDEO IN
Y
component
video cable
PR/CR
PB/CB
L
AUDIO IN
R
COMPONENVIDEO OUT
Y
P
B
PR
R
L
ANALOG AUDIO
OUTPUT
composite audio cable
Connecting to a TV using an A/V cable (Good)
COMPONENT VIDEO OUT
SBL
C
SL
FL
Y
P
B
PR
AC IN
SBR
SW
SR
FR
R
L
BITSTREAM
/
PCM
VIDEO
OUT
LAN
USB
HDMI OUT
OPTICAL
AUDIO OUT
MULTI CHANNEL AUDIO OUTPUT
C
VIDEO IN
Your TV
R
L
VIDEO
OUTPUT
ANALOG AUDIO
OUTPUT
L
AUDIO IN
R
composite audio video cable
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to an Audio System
•
•
When you change the connections, all devices should be turned off.
Refer to the manual accompanying external devices for more information.
Via 2-Channel Analog Audio Output
Stereo system
COMPONENT VIDEO OUT
SBL
C
SL
FL
Y
PB
PR
AC IN
SBR
SW
SR
FR
R
L
BITSTREAM
/
PCM
VIDEO
OUT
LAN
USB
HDMI OUT
OPTICAL
AUDIO OUT
MULTI CHANNEL AUDIO OUTPUT
AUDIO IN
R
L
R
L
ANALOG AUDIO
OUTPUT
composite audio cable
Via Digital Audio Output
AV receiver / amplifier
COMPONENT VIDEO OUT
SBL
C
SL
SR
FL
FR
Y
PB
PR
AC IN
SBR
SW
R
L
BITSTREAM
/
PCM
VIDEO
OUT
LAN
USB
HDMI OUT
OPTICAL
AUDIO OUT
MULTI CHANNEL AUDIO OUTPUT
DIGITAL AUDIO INPUT
OPTICAL
BITSTREAM/PCM
OPTICAL
digital audio optical cable
Via HDMI Audio Output
AV receiver / amplifier
with an HDMI input jack
COMPONENT VIDEO OUT
SBL
SBR
C
SL
SR
FL
FR
Y
PB
PR
AC IN
SW
R
L
BITSTREAM
/
PCM
VIDEO
OUT
LAN
USB
HDMI OUT
OPTICAL
AUDIO OUT
MULTI CHANNEL AUDIO OUTPUT
HDMI IN
HDMI cable
HDMI OUT
.
Digital Audio Optical Cable and HDMI Cable NOT INCLUDED.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Network Connection
Your Blu-ray disc player can be connected to your home network:
•
By connecting an Ethernet cable to the ETHERNET jack on the rear of your player and to a wired hub or router. Using
a wired network provides the best performance, because the attached devices connect directly to the network and are
not subject to radio frequency interference.
•
By connecting through the built-in wireless device and a wireless access point or router.
Connecting your player to a wired router:
•
Connect an Ethernet cable (CAT5 or better with RJ45 connector) to the ETHERNET jack on the back of your player
and to an Ethernet jack on a hub or broadband router.
Hub or broadband router
Networking equipment
(modem, etc.)
Notes:
•
Do not connect a modular
phonecabletotheETHERNET
jack.
WAN
LAN
LAN
•
When plugging or unplugging
the cable, hold the connector
on the end of the cable.When
unplugging, do not pull on the
cable.Press down the lock tab
and pull the connector out of
the jack.
5
4
3
2
1
LAN cable
LAN cable
•
Because there are various
connection configurations,
follow the instructions from
your telecommunication carrier
or Internet service provider.
Internet
LAN
COMPONENT VIDEO OUT
SBL
SBR
C
SL
SR
FL
FR
Y
PB
PR
AC IN
SW
R
L
BITSTREAM
/
PCM
VIDEO
OUT
LAN
USB
HDMI OUT
OPTICAL
AUDIO OUT
MULTI CHANNEL AUDIO OUTPUT
Connecting your player to a wireless access point or router:
Your Blu-ray disc player has an integrated Wi-Fi device and antenna. No physical connection to the wireless router is
necessary.
•
Configure your player to access the wireless access point or router. For more information, see “Configuring a wireless
Internet connection” on page 36.
•
The network configuration and connection method may vary depending on the equipment in use and the network
environment. Your Blu-ray disc player is equipped with an IEEE 802.11n wireless module, which also supports the
802.11 a/b/g/n standards. For the best wireless performance, we recommend using an IEEE 802.11n certified Wi-Fi
network (access point or wireless router).
Notes:
• You must use a wireless IP sharer that supports IEEE 802.11 a/b/g/n.
(n is recommended for stable operation of the wireless network.)
• Wireless LAN, in its nature, may cause interference, depending on the
use condition (AP performance, distance, obstacle, interference by
other radio devices, etc.).
Wireless access point
Modem Port
• Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not
supported.
Modem Cable
• When applying the security key for the AP (wireless IP sharer), only
the following is supported.
1) Authentication Mode : WPAPSK, WPA2PSK
2) Encryption Type : WEP, TKIP, AES
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Speakers (For 7.1 Audio Channel)
You can connect the speakers as shown in the following diagram to obtain the 7.1 audio channels effects. Using the audio
cables, connect the MULTI CHANNEL AUDIO OUTPUT (SBL, SBR, C, SW, SL, SR, FL & FR) terminals on the rear of
the Blu-ray disc player to 7.1 Channel ANALOG AUDIO IN terminals of your Amplifier.
For speaker configuration, please refer to “Speaker Setting” on page 32.
COMPONENT VIDEO OUT
SBL
C
SL
FL
FR
Y
PB
PR
AC IN
SBR
SW
SR
R
L
BITSTREAM
/
PCM
VIDEO
OUT
LAN
USB
HDMI OUT
OPTICAL
AUDIO OUT
MULTI CHANNEL AUDIO OUTPUT
SBL
C
SL
SR
FL
FR
SBR
SW
MULTI CHANNEL AUDIO OUTPUT
7.1 Channel Amplifier
L
L
L
R
R
R
Notes:
• Please turn the volume down when you turn on the Amplifier.Sudden loud sound may cause damage to the speakers
and your ears.
• The position of terminals may vary depending on the Amplifier. Please refer to the user’s manual of your Amplifier.
• The front left and right outputs on your player and 7.1 channel amplifier must be connected to hear disc menu audio
from certain Blu-ray discs.
• When connecting to a 5.1 channel home theater or receiver, connect all the MULTI CHANNEL AUDIO OUTPUT jacks
from the player except for the SBL (Surround Back Left) / SBR (Surround Back Right) outputs.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Positioning the Speakers (For 7.1 Audio Channel)
How you set up your speakers can affect the bass and the sound field. Note the following points:
•
•
Place speakers on flat secure bases.
Placing speakers too close to floors, walls, and corners can result in excessive bass. Cover walls and windows with
thick curtains.
•
Keep your speakers at least 10 mm away from the system for proper ventilation.
Setup example (For 7.1 audio channels)
Subwoofer
Front speakers
Center speaker
Place the left and right front
speakers equidistant from the
center speaker, about 30
Place the center speaker directly in front of the
listening area, either above or below the TV.
Vibration caused by the speaker can disrupt the
picture if it is placed on directly on the TV.
o
angle from the center channel.
Place to the right or left of the
TV, on the floor or a sturdy
shelf so that it will not cause
vibration. Leave about 30 cm
from the TV.
Main unit
To allow for proper ventilation and to maintain
good airflow around the main unit, position it with
at least 5 cm of space on all sides.
AV receiver
Place the AV receiver directly in front of the
listening area, either above or below the TV.
Left & Right Surround speakers
(may be elevated above
the listener)
Surround Back speakers
(may be elevated above
the listener)
Place the left and right surround speakers to the
left and right side of the listening position, in line
with or slightly behind the listening position -
Place the surround back speakers behind the
listening position - slightly to the left and right -
at about 140 -150 from the center speaker.
o
o
o
o
about 90 -110 from the center.
Note:
The above setup illustration is a basic overview on what to expect when hooking speakers up to your home theater system. The
placement may vary depending on how many and what type of loudspeakers you have, as well as your room size, shape, and
acoustical properties.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Readable cards
SD Memory Card (8 MB - 2 GB)
SDHC Memory Card (4 GB - 8 GB)
miniSD Card (8 MB - 2 GB)
Playable files/data
Information on Playback
MP3, Windows MediaTM
Audio, JPEG, picture-
Before you start playing back a disc, read the following
information.
in-picture
commentary,
subtitles or other extras
for BD-ROM
microSD Card (8 MB - 2 GB)
Playable Discs and Files
•
This unit supports SD Memory Card with FAT12/FAT16
file system, and SDHC Memory Card with FAT32 file
system.
This unit is compatible to play back the following discs /
files.
•
•
This unit does not support NTFS file system.
This unit may not read the SD Memory Cards formatted
on a computer. If that is the case, please reformat the SD
Memory Cards in this unit and try again.
This unit does not support miniSDHC and microSDHC
Memory Card.
To play back a disc / file, make sure that it meets the
requirements for region codes and color systems as
described below. You can play back discs that have the
following logos.
•
•
Other disc types are not guaranteed to play back.
For miniSD Card and microSD Card, the adapter is
necessary.
Playable discs
Logos
Blu-ray Disc
miniSD Card
microSD Card
adapter
- BD-ROM (single / dual layer)
- BD-RE (single / dual layer)
(Recorded in BDMV format)
- BD-R (single / dual layer)(Recorded
in BDMV format) (Unclosed discs
may not be played back.)
adapter
miniSD Card
microSD
Card
•
•
Portions of this product are protected under copyright
law and are provided under license by ARIS / SOLANA /
4C.
Please keep the SD Memory Cards in their cases when
you are not using them.
Do not try to open or modify the card.
Do not touch the terminal surface with your fingers or
any metals.
Do not attach additional labels or stickers to cards.
Do not remove the label of the SD Memory Cards.
This unit recognizes up to 8 characters of file name in
the SD Memory Card. Characters after 8th will not be
displayed.
DVD-ROM
DVD-RW
DVD-R
•
•
•
•
•
CD-DA (audio CD)
CD-RW
Unplayable Discs and Files
CD-R
The following discs will not be played back in this unit.
DTS-CD
-
•
•
•
•
•
•
•
•
•
•
•
•
•
CD-ROM
CD-I (compact disc-interactive)
DVD-RAM
VSD (video single disc)
DVD-audio
HD DVD
VIDEO CD
Unfinalized disc
Playable files
Media
AVCHD
MP3
DVD-RW/-R
BD-RE/-R,
RW/-R,
DVD-RW/-R,
Memory
(including SDHC), miniSD Card,
microSD Card
CD-
Card
Windows MediaTM Audio
SD
SACD
BD / DVD / SD Memory Card contains DivX® files.
BD / DVD hybrid disc (played back as a BD-video only)
BD that contains AVCHD files
DVD-RW/-R recorded in non compatible recording
format.
JPEG
•
This unit cannot playback the disc contents protected by
Windows MediaTM Digital Rights Management (DRM).
•
•
Super Audio CD - Only the sound on the CD layer can be
heard. The sound on the high-density Super Audio CD
layer cannot be heard.
Playability of dual discs are not guaranteed.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Color Systems
Structure of Disc/SD Card Contents
BD-video and DVD-video are recorded in different color
systems throughout the world. The most common color
system is NTSC (which is used primarily in the United
States and Canada).
The contents of BD / DVD / AVCHD are generally divided into
titles. Titles may be further subdivided into chapters.
BD / DVD / AVCHD
title 1
chapter 1
title 2
chapter 2 chapter 1 chapter 2 chapter 3
Region Codes
This unit has been designed to play back BD-video with
region “A” and DVD-video with region “1” or “ALL”. You
cannot play back BD-video or DVD-video that are labeled
for other regions. Look for the symbols on the right on your
BD-video or DVD-video.
Audio CD is divided into tracks.
audio CD
track 3
track 1
track 2
track 4
track 5
If these region symbols do not appear on your BD-video or
DVD-video, you cannot play back the disc in this unit. The
letter or number inside the globe refers to region of the world.
A BD-video or DVD-video labeled for a specific region can
only be played back in the unit with the same region code.
Data discs, USB device, SD Memory Cards containing MP3
/ WMA /JPEG are divided into folders, and the folders are
subdivided into files.
MP3 / WMA / JPEG
BD-video
folder (group) 2
file 4
folder (group) 1
file 1
file 2
file 3
file 5
DVD-video
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION:
Playing a Disc
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
This section shows you the basics on how to play a disc.
Basic playback
Preparations
• When you want to view a disc, turn on the TV and select the video input connected to the Blu-ray disc player.
To start playback in the stop mode
Press the ON/STANDBY button.
Press PLAY.
1
The Blu-ray disc player turns on.
To pause playback (still mode)
Press PAUSE during playback.
To resume normal playback, press the PLAY button.
Press OPEN/CLOSE.
• The sound is muted during still mode.
2
The disc tray opens.
To stop playback
Press STOP. The home menu is displayed.
For Blu-ray discs, press
OK to start playback at the beginning of the disc.
/
to select BD-ROM, then press
Place the disc on the disc tray.
3
For DVDs/audio CDs, press
playback.
PLAY to resume normal
With the playback side
down
• Depending on the disc, playback starts where it stopped
or at the beginning of the disc.
• If you press STOP twice, playback stops completely. To
stat playback again, press
the beginning of the disc.
PLAY. Playback starts at
Press OPEN/CLOSE to close the disc tray.
4
Playback starts.
To remove the disc
Press OPEN/CLOSE.
If you insert a Blu-ray disc or a DVD that contains
a top menu, a menu may appear. Use
to select the title you want to view, then press OK
to start playback.
/
/
/
Remove the disc after the disc tray opens
completely.
Be sure to press the OPEN/CLOSE button
to close the disc tray after you remove
the disc.
• You may need to press the POPUP/TOP MENU or
MENU button to display disc menu (depending on
the actual Blu-ray disc or DVD.)
To turn the power off
Press ON/STANDBY button to turn the unit off.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Variable Speed Playback
You can play discs at various speeds, and resume playback from the location where you stopped playback.
Playing in fast reverse / forward directions
To resume normal playback
Press
or
during playback.
Press
PLAY.
: Fast forward playback
: Fast reverse playback
Notes:
• The Blu-ray disc player mutes sound and subtitles during
reverse and forward scan.
• The playback speed may differ depending on the disc.
Each time you press this button, the fast-forward
or fast-reverse speed changes in the following
sequence:
Fast x 2
Fast x 4
Fast x 8
Fast x 16
Fast x 32
Fast x 64
Fast x 128.
Playing frame by frame
To resume normal playback
Press
during still playback.
Press
PLAY.
Each time you press this button, the picture
advances one frame.
Note: The sound is muted during frame by frame playback.
Playing in slow motion
To resume normal playback
Press
during playback.
Press
PLAY.
Each time you press this button, the slow-
motion speed changes in the following
sequence:
Notes:
• The sound is muted during slow-motion playback.
• 3 speeds are available.
Slow x 1/2
Slow x 1/4
Slow x 1/8
Locating a Desired Section
Normally, Blu-ray discs and DVDs are divided into titles, and the titles are sub-divided into chapters. Audio CDs are divided
into tracks.You can quickly locate any specific title, chapter, or track.
Locating a title using the top menu
Press
want.
/
/
/
to select the title you
Press POPUP/TOP MENU.
1
2
3
The top menu appears on the TV
screen.
If the titles in the top menu are assigned a number,
you can directly locate a specific title by pressing its
designated number with the number buttons.
e.g.
Press OK.
Playback starts from Chapter 1 of the selected title.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Locating a specific chapter or track
Press
or
repeatedly to access the
and
refer to item
26 and item 10 on page 9 and
page 8 respectively.
chapter or track number you want.
Playback starts from the selected chapter or track.
You can also press
or
To locate succeeding chapters or tracks.
(shown as in the right
illustration) on the remote
control to access the desired
chapter or track.
Playback starts from the beginning of the
current chapter or track.When you press twice
in quick successions, playback starts from the
beginning of the preceding chapter or track.
Note: Some titles may not display chapter numbers.
Accessing a Specific Location Directly
Locating a specific title/chapter/time
Press GOTO.
(Press GOTO once)
1
The Goto menu appears on the TV screen.
Goto Track:
/ 21 (Current: 10)
e.g.
the currently
playing track
number
the desired
track number
the total
track number
a. Press the GOTO button once:
(Press GOTO once)
Goto Title:
/ 4 (Current: 1)
Goto File:
/ 21 (Current: 10)
the total
the desired
title number
the total
title number
the currently
playing title number
the desired
file number
the currently
playing file number
file number
(Press GOTO twice)
b. Press the GOTO button twice:
Goto Time:
:
:
/ 01:50:46 (Current: 0:05:52)
Goto Chapter:
/ 30 (Current: 6)
the desired time
(hh:mm:ss)
the total time
the elapsed
time
the currently
playing chapter
number
the desired
chapter number
the total
chapter number
Press the number buttons to enter title,
2chapter (track) number or time.
While accessing the TIME using number buttons, just
enter 2 digits in order.
c. Press the GOTO button for 3 times:
The first two numbers you entered represent hours.
The second two numbers you entered represent
minutes.
Goto Time:
:
:
/ 01:50:46 (Current: 0:05:52)
The third two numbers you entered represent seconds.
the desired time
(hh:mm:ss)
the total time
the elapsed
time
Press the CLEAR button to reset the numbers.
Press OK.
3
Playback starts from the selected section.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Repeating a Title, Chapter, Track or Specific Segment
Repeating a title, chapter or track
Press REPEAT repeatedly to select the
desired repeat mode during playback.
e.g.
Repeat Off
Repeat All
Repeat Off
Notes:
•
•
•
•
•
The repeat setting will be cancelled when you stop
playback.
The chapter, title or track repeat will be cleared when moving
to another chapter, title, track / file or folder.
Repeat playback does not function during A-B repeat
playback.
Chapter and title repeat are not available with some
scenes.
Repeat Off
Repeat Off
Repeat Title
Repeat Chapter
Repeat Off
Repeat Off
Repeat All
Repeat Track
When the repeat setting is set for a MP3 or WMA folder (file),
the repeat setting will be cancelled if you select other MP3 or
WMA folder (file) to playback.
Repeat Off
Repeat All
Repeat File
Repeat Off
Repeating a specific segment
To resume normal playback
Press A-B at the desired starting point
A during playback.
Press A-B until Repeat Off is displayed.
1
Notes:
Repeat A-
•
•
Some discs may not permit A-B repeat operation.
You can specify a segment only within the current title or
track.
Press A-B at the desired ending point B
during playback.
2
•
•
You cannot set the A-B repeat function for a segment that
includes multiple camera angles.
A-B repeat does not function during chapter, title, track or all
repeat playback.
Repeat A-B
The BD player automatically returns to point A and
starts repeat playback of the selected segment
(A-B).
Playing in a Random Order
Playing tracks or files in a random order
To resume normal playback
Press RANDOM repeatedly until “Random Off” is displayed.
Press RANDOM repeatedly to select
Random ON during playback.
Once you turn RANDOM function on, the RANDOM
indicator will be activated and the system will play all files
in a random sequence.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PIP (BONUSVIEW) Setting
Some Blu-ray discs have the PIP function which enables you to display the secondary video in the primary video.You can call
up the secondary video by pressing BONUSVIEW whenever the scene contains the secondary video.See the documentation
that came with the disc for playback instructions.
Press BONUSVIEW during playback to
turn PIP mode on.
BONUS VIEW
1
Primary video
Press 2nd AUDIO to turn the audio for the
video in the PinP window on or off.
2
3
Secondary video
To resume normal playback
Press BONUS VIEW to turn off the PIP mode.
Press 2nd SUBTITLE to turn the subtitle
for the video in the PinP window on or
off.
Note: PIP audio cannot be heard unless Bitstream Mixed has
been selected on the Audio menu. For more information, see
“Audio Setting” on page 31.
Camera Angle
Some BD-video and DVD-video contain scenes which have been shot simultaneously from various angles.
The selected angle will be displayed on the display bar
During playback, press ANGLE.
at the top of the TV screen.
Angle
1
1/3
The first digit indicates the current viewing angle, and
the second digit indicates the total number of viewing
angles.
Press , then use
/
to select the
2desired angle.
Audio Selection
In the example “01/03 ENG Dolby TrueHD”,
During playback, press AUDIO.
“01” indicates the currently selected audio channel.
“03” indicates the total number of audio channels.
“ENG” indicates the audio language.
“DolbyTrueHD” describes the currently selected audio
format.
1
Press , then use
/
to select the
2
desired audio language and audio
format.
Notes:
•
The available options of Audio vary from different disc
format.
PIP Audio is not available for all discs.It only applies to Blu-ray
discs that supports picture-in-picture features.
Audio
01/03 ENG Dolby TrueHD
01/03 ENG Dolby TrueHD
PIP Audio
•
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Subtitle Selection
In the example “01/07 ENG”,
During playback, press SUBTITLE.
“01” indicates the currently selected subtitle.
“07” indicates the total number of subtitles.
“ENG” indicates the subtitle language.
1
Press , then use
desired subtitle.
/
to select the
2
Notes:
•
The available options of Subtitle vary from different disc
format.
Subtitle
01/07 ENG
NA
•
PIP Subtitle is not available for all discs. It only applies to
Blu-ray discs that support picture-in-picture features.
PIP Subtitle
Displaying On-screen Information
You can check information about the current disc by pressing
.
On-Screen display
Disc format
On-Screen Display
Title 1 Chapter 1/25
BD-ROM
0:02:00
1:57:35
Off
Play
Play
Play
Title 1 Chapter 1/18
0:02:00
DVD
1:57:35
Off
Track 1/12
0:00:20
CD-DA
0:05:35
Off
Off
File: 1/5 song1.mp3
Title: Cool Track
Artist: Ricardo Funiccio
Album: Dead Dux
Off
Off
Play
0:02:00
0:30:00
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing AVCHD/MP3/WMA/JPEG Files
You can play AVCHD, MP3, WMA or JPEG files that have been recorded on a disc on the Blu-ray disc player.
Playing files on a data disc
When you insert a data disc containing picture, music, or video files into your player, icons are added to the menu to
indicate that video, music, or picture files are available for playback.
If a USB device and a SD card containing music
are inserted at the same time, the system will
enter the source selection screen shown as
below:
Press OPEN/CLOSE to open the disc
tray, place a disc that contains video/
MP3/JPEG files.
1
A selection menu will appear on the screen.
Music
Video
Music
USB1
2 item(s)
Settings
Blockbuster
Netflix
Main Menu
Optical Disc
SDIO
Connected
Pandora
Browse Pictures
Now Playing
Vudu
Music
Pictures
For SD card and USB device operation, please
refer to “Using an SD card”on page 26 and “Using
a USB Device” on page 27.
Press
/
to select the Music or
2
Pictures, and then press OK.
(For example: selecting the Music)
Press
/
to select the desired MP3 file,
If no USB device or SD card is inserted, the system
will directly access the following screen:
3
4
and then press OK to start playing.
File: 1/5 song1.mp3
Title: Cool Track
Artist: Ricardo Funiccio
Album: Dead Dux
Music
0:02:00
0:30:00
On
Off
Play
Optical Disc
10 item(s)
1
2
: Press RANDOM repeatedly to turn random
playback on or off.
File
Information
Playlist
Main Menu
:Press REPEAT repeatedly to select the
desired repeat mode.
Play Files
Browse Pictures
Now Playing
To view JPEG picture files while playing
music files, follow the following steps:
1. Press RETURN.
2. Use
/
to select Browse Pictures, then
3
4
press OK.
: displays source (Optical Disc/USB/SD) device name.
: defines the total number of files that a device contains.
: shows all files name.
1
2
3
4
3. Select the desired JPEG file and press OK to
start viewing.
: shows the information on the currently selected file.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Slide Show Effects
Slide Show Delay
None
No Delay
Ok
Pictures
Optical Disc
30 item(s)
1
2
Main Menu
Settings
Main Menu: Returns to the main menu.
Thumbnail
Media Menu
Media Menu: Returns to select the source. This item only
appears if your optical disc, USB device or SD card is
inserted.
Start Slide Show
Browse Music
Previous Folder:This item only appears if your optical disc,
USB device or SD card contains several different picture
folders.
Now Playing
File: 13/30
3
Start Slide Show: This option enables you to view picture
(files) one after another automatically.
4
: displays source (Optical Disc/USB/SD) device name.
: defines the total number of files that a device contains.
: shows the currently playing file number.
1
2
3
4
Browse Music: Goes back to Music folder.
To stop playing and return to the main
menu, follow one of the steps described
below:
: shows all pictures in thumbnail mode.
5
Settings: This option enables you to define Slide Show
Effects (None, Horizontal Scroll, Fade and Shutter) and
Slide Show Delay (5 Seconds, 2 Seconds, 1 Seconds,
No Delay, 10 Seconds, 15 Seconds and 30 Seconds).
After setting, press to highlight Ok and then press OK
to confirm.
•
•
•
Press STOP.
Press RETURN.
Press , then use
/
to highlight Main Menu
and then press OK to confirm.
Using an SD Card
This unit supports the use of a Secure Digital (SD) card (not
included).
CAUTION:
Before inserting the SD card, please read carefully the
relevant information on “Playable Discs and Files” on
page 17.
Inserting an SD card
If no USB device or optical disc containing music or pictures is
inserted, the system will directly load the data on the inserted
SD card. Otherwise, it will enter the source selection screen.
If so, please follow the operation instructions in “Playing files
on a data disc” on page 25 for details.
Inserting an SD card fully into the slot
on the front of Blu-ray disc player until
it clicks as illustrated.
1
To pause playback
Press during playback. To resume normal playback,
press PLAY.
To stop playback
Press STOP.
SD/SDHC
Card
Removing the SD card
In stop mode, gently push the SD card into the slot and
then pull it out slowly.
Press
and then press OK.
/
to select Music or Pictures,
Notes:
•
If you cannot easily insert the memory card, you may have
inserted it incorrectly.Try to turnover the card and then insert
again. Do not force the memory card into the memory card
slot.
2
•
Do not remove the SD card during playback.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a USB Device
You can play MP3, WMA or JPEG files that have been stored on USB devices on the Blu-ray disc player.
Operating a USB device
To pause playback
Press during playback. To resume normal playback,
press PLAY.
Inserting a USB device into the USB
slot on the back of Blu-ray disc player
until it clicks.
1
To stop playback
Press STOP.
Press
/
to select Video, Music or
Removing the USB device
In stop mode, gently pull the USB device out slowly.
Pictures, and then press OK.
2
If no optical disc or SD card containing music or
pictures is inserted, the system will directly load
the data on the USB device. Otherwise, it will enter
the source selection screen. If so, please follow the
operation instructions in “Playing files on a data
disc” on page 25 for details.
Notes:
•
If you cannot easily insert the USB device, you may have
inserted it incorrectly. Try to turnover the device and then
insert again.
• Do not remove the USB device during playback.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
Customizing the Function Settings
You can change the default settings to customize performance to your preference.
3. Follow the on-screen instructions to customize the
General Operations
following settings to your preference:
OSD Language Settings
Resolution
•
•
•
•
•
•
1. Press
/
to select Settings in home menu while in full
stop mode, the Settings menu appears.
TV Aspect
2. Press button, then use
options.
/
button to select the setting
Wireless
Optical Disc Auto Play
Screen Saver Duration
3. Press OK button.
4. Press
menu.
or RETURN button to return to the previous
4. After setting, press OK to confirm and exit the setup.
Note: If it is the first time for the player to start up or users
restore all settings to factory defaults, the system will prompt
you to perform Quick Setup. Repeat the steps described as
above to complete the setup.
Home Menu
Info
Quick Setup
BD-ROM
Display
BD-Live
HDMI Status
Connected
1080p(HDMI)
HDMI Auto
16:9 Pillarbox
Off
HDMI Preferred Format
Resolution
Settings
Display
TV Aspect
Using BD-Live™ Features
Film Mode
Deep Color
On
Audio
Bluray 3D Mode
Automatic
Some (but not all) BD discs contain additional features
that are made available to players that are connected to
the internet, and have additional memory added. These
additional features may include things like:
Connected
Speaker
A
Language
•
•
•
the ability to download new movie trailers
additional ‘commentary’ by actors and directors
multiperson game play and chat
Settings menu items submenu display area
In order to access BD-Live functions, the player must be
properly configured for BD-Live internet access, and it must
be equipped with additional memory.
Info Menu
1. In the main menu of Settings, press button, then use
This submenu displays the following information:
/
button to select BD-Live, then press OK.
•
•
•
Software Version
Software Date
Netflix ESN
BD-Live
BD-Live Internet Access
Always Allow Access
N/A
1. In the main menu of Settings, press button, then use
button to select Info to display the software version,
software date and Netflix ESN.
BD-Live Storage
/
Erase Blu-ray Storage
2. Press or RETURN to go to the previous menu.
Performing Quick-Setup
1. In the main menu of Settings, press button, then use
/
button to select Quick Setup, and then press OK
to confirm.
2. Press
3. Use
OK to confirm.
/
to select an option, and then press OK.
2. Press OK to perform Quick Setup.
To exit the setup menu:
/
to select the desired setting, and then press
• Use button to highlight “No thanks.I’ll go through the
full setup menu later”, and then press OK.
• Or press button directly.
4. Press to go to the previous menu.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the Function Settings
BD-Live Internet Access:
Display Setting
•
•
•
Limit Access — Allows Internet access with valid “BD-
Live” network access approval.
Always Allow Access — Always allows BD-Live Internet
access.
1. In the main menu of Settings, press button to select
Display, and then press OK to confirm.
Prohibit Access — Never allows BD-Live Internet
2. Press
3. Use
/
to select an option, and then press OK.
access.
/
to select the desired option, and then press
In order to set the player up for BD-Live Internet Access,
perform the following steps:
OK to confirm your selection.
4. Press to go to the previous menu.
1. In the main menu of Settings, press button, then use
/
to select BD-Live, then press OK.
2. Press
/
to select “BD-Live Internet Access”, and
Display
then press OK.
3. Use
/
to select the desired setting, and then press
HDMI Status
HDMI Preferred Format
Resolution
Connected
OK to confirm.
4. Make sure that “Limit Access” or “Always Allow
1080p
Access” is checked.
HDMI Auto
16:9 Pillarbox
Off
5. Once the USB device or SD card has been inserted, if
there is not at least 100Mbyte of free space on the device,
you should choose “Erase Blu-ray Storage” from the
BD-Live setup menu.
TV Aspect
Film Mode
Deep Color
On
6. Press to return to the main menu of Settings, then
Bluray 3D Mode
Automatic
use
/
to highlight Network, and then press OK. (For
details, please refer to “Network Connection Setting” on
Page 36.)
Notes:
•
•
•
Depending on your connection environment, it may take
time to connect to the Internet or the Internet may not be
connected.
When BD-Live function are used and the unit is
connected to the Internet, you may be charged for this
communication.
HDMI Status:
This option displays the HDMI status. If an HDMI TV is
connected, Connected appears. If an HDMI TV is not
connected, Disconnected appears.
HDMI Preferred Format:
Do not remove the USB device or SD card when using
the BD-Live function.
This option shows the best HDMI format for the connected
TV.
BD-Live Storage:
Resolution:
This option is used to tell the BD player whether or not to
use an inserted SD card or USB device to store BD-Live
content (movie trailers, additional scenes, etc.).
You can define the video output resolution in this option. In
case that the menu of “Resolution”setting disappears, make
composite video (yellow) connection to restore it, then select
the resolution which is compatible with the connected TV.
In order to add BD-Live memory for BD-Live Internet Access,
insert an USB device or SD card (1GB is recommended)
into the USB slot or SD card slot on the player.
Notes:
•
Selecting a resolution the TV does not support could
result in an unstable picture or loss of the picture. See
the documentation that came with the TV to find the
resolutions the TV supports.
Erase Blu-ray Storage:
If you choose OK to erase Blu-ray storage, all bookmarks
and BD-Live content saved in memory are deleted.
•
Only the HDMI output on your player supports 1080p
video output at any frame rate. If the TV is connected
to the component output, the video output is limited to
1080i or lower.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
Customizing the Function Settings
Deep Color:
TV Type
Resolution
This option decides whether to turn off the Deep Color
(color depth) setting for video signals output from the HDMI
OUT jack.
If your TV is a high-definition TV(HDTV)
connected to the HDMI jack on your
player and you want your player to set
the output resolution based on informa-
tion exchanged between the TV and your
player over the HDMI cable.
HDMI Auto
Connecting the player and a TV that supports Deep
Color allows more accurate color reproduction than when
connecting it to a TV that does not support Deep Color. It is
recommended to set this option Off if the picture is unstable
or colors appear unnatural.
If the TV is a high-definition TV (HDTV)
capable of 1080p (any frame rate) con-
nected to the HDMI jack on your player
1080p
Bluray 3D Mode:
If your TV is a high-definition TV (HDTV)
capable of 1080i only
1080i
720p
480p
480i
Select whether to play a Blu-ray Disc with 3D contents in
3D Mode.
If your TV is a high-definition TV (HDTV)
capable of 720p only
Automatic: The 3D Blu-ray disc is played in 3D mode if
your product detects a TV which supports it. It is played
in 2D mode if your product detects a TV which can not
support it.
If your TV is an enhanced-definition TV
(EDTV)
If your TV is a standard-definition NTSC
TV (American or Asian SD TV)
Forced 2D:The 3D Blu-ray disc is played in 2D mode at all
times. Select this option to view a picture without 3D effect
or when a TV cannot support 3D Blu-ray discs.
TV Aspect:
Notes:
Depending on the type of television you have, you may want
to adjust the screen setting.
•
If you or any viewer experiences the following symptoms
or any other discomfort from viewing 3D video images,
stop viewing and contact your health care provider:
•
•
16:9 wide — You can view the full 16:9 picture on your
widescreen TV.
Convulsions, Eye or muscle twitching, Loss of awareness,
Altered vision, Involuntary movements, Disorientation,
Eye Strain, Nausea/Vomiting, Dizziness, Headaches or
Fatigue
16:9 Pillarbox — Movie will be displayed in the center of
the screen and vertical bars will appear on sides of the
screen.
•
•
Carefully read instructions provided with your display
and/or 3D glasses before 3D viewing.
•
•
4:3 Pan and Scan — Select when you want to see the
16:9 video supplied by the Blu-ray Disc/DVD without the
black bars on top and bottom, even though you have aTV
with a 4:3 ratio screen.The extreme left and right portion
of the movie picture will be cut off.
If you want to enjoy a 3D content, connect a 3D device
(3D compliant AV receiver orTV) to the product and wear
a 3D glass before playing the 3D content.
•
•
•
While watching the 3D video, all analogue component
and composite signals will be blocked automatically.
4:3 Letterbox — Select when you want to see full 16:9
ratio image supplied by a Blu-ray Disc/DVD, even though
you have a TV with a 4:3 ratio screen. Black bars will
appear at the top and bottom of the screen.
All 3D signals are output only using the HDMI cable and
through the HDMI OUT port.
As the video resolution in 3D play mode is fixed according
to the resolution of the original 3D video, you can not
change the resolution to your preference.
Notes:
•
Depending on the disc type, some aspect ratios may not
•
•
You must use a high-speed HDMI cable for a proper
output of the 3D signal.
be available.
•
If you select an aspect ratio and option which is different
from the aspect ratio of yourTV screen, the picture might
appear distorted.
You can not use this product for switching a 2D content
to 3D.
Film Mode:
Movies are recorded on film at a rate of 24 pictures (frames)
per second.Many of the movies on Blu-ray discs are placed
on the discs at this frame rate.If yourTV supports 24 frames
per second, but you would prefer viewing the video at a
higher frame rate, you should turn off Film Mode.Off selects
a 60 frames/second output format.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the Function Settings
Note: Incorrectly setting the digital audio output’s PCM
sampling rate too high may result in unpredictable audio
playback.
Audio Setting
The settings in the Audio menu will configure the BD player’s
digital audio outputs (HDMI or Optical).
Digital Output:
•
PCM Stereo — Sets the output to PCM Stereo if you
have not an audio receiver connected to your Blu-ray
disc player or the audio receiver connected to Blu-ray
disc player is not a 5.1/7.1 channel receiver.
1. In the main menu of Settings, press button, then use
/
button to select Audio, then press OK button.
•
Bitstream HD — Lets your player send Dolby TrueHD
or DTS-HD MA bitstreams over HDMI (if your player is
connected to a compatible HDMI audio receiver). If your
player is not connected to a compatible HDMI receiver
(for example, your player is connected directly to the TV
or your player is connected to an audio receiver using an
optical cable), a compatible audio signal is automatically
sent over the HDMI and optical connections. With this
setting, Blu-ray audio is limited to the soundtrack for the
main movie (no PIP audio).
Audio
PCM Downsampling
48 kHz
PCM7.1
On
Digital Output
Dynamic Range Control
Stereo Downmix
Auto
•
•
Bitstream Legacy — Sends a DTS or Dolby Digital
bitstream from the disc over the HDMI and optical
connections. Blu-ray audio is limited to the soundtrack
for the main movie (no PIP audio).
Bitstream Mixed — Sends a mixed (PIP audio and movie
audio) DTS audio stream over the HDMI and optical
connections.This mode is primarily intended for use when
you want to hear both PIP audio and the movie audio.
2. Press
3. Use
/
to select an option, and then press OK.
/
to select your preferred audio items, and then
press OK to confirm your selection.
•
•
PCM 5.1 — Sends a PCM audio signal of up to 5.1
channels over the HDMI connection and up to 2 channels
over the optical connection.
4. Press to go to the previous menu.
PCM Downsampling:
PCM 7.1 — Sends a PCM audio signal of up to 7.1
channels over the HDMI connection and up to 2 channels
over the optical connection.
If you don’t have a surround sound receiver connected to
the BD player, you should leave the PCM downsampling
to 48 kHz, and proceed to the next setup menu item. This
is true regardless of whether the audio is connected to the
TV with HDMI or the analog stereo outputs.
Dynamic Range Control:
Dynamic Range Control means that you can allow the BD
player to make the loud parts of a movie’s audio track quieter
than they would be in the theatre, without making the dialog
of the actors any quieter.
If you have a surround sound receiver connected to
the BD player, and you have connected to the surround
receiver via the BD player’s analog multichannel audio
outputs, this setting has no effect on the audio going to the
analog outputs of the player.Leave the PCM downsampling
to 48 kHz, and proceed to the next setup menu item.
This would be useful, for instance, when you want to watch
a movie in the evening when others might be sleeping.
Notes: This setup menu item has no effect unless:
If you have a surround sound receiver connected to
the BD player, and you have connected to the surround
receiver via the BD player’s HDMI output, this setting has
no effect on the audio going to the HDMI output of the player.
Leave the PCM downsampling to 48 kHz, and proceed to
the next setup menu item.
•
•
The device playing the disc’s audio (TV or surround audio
receiver) is connected to the BD player’s analog audio
outputs; OR
you have selected “Bitstream Mixed” in the BD player’s
audio setup menu.
When Dynamic Range Control is set to Off, movie
soundtracks are played with the standard dynamic range.
If you have a surround sound receiver connected to
the BD player via optical cable, set this menu item to the
maximum PCM sampling rate that your surround receiver When movie soundtracks are played at low volume or from
can accept (48 kHz or 96 kHz). If in doubt, consult your smaller speakers, you can set Dynamic Range Control to
surround receiver’s manual or set to 48 kHz.
On. Your player applies appropriate compression to make
low-level content more intelligible and prevent dramatic
passages from getting too loud.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
Customizing the Function Settings
Selecting the “Auto” option turns on the Dynamic Range
Control for all BD movie soundtracks except Dolby TruHD. If
you have selected a TruHD track on the BD disc, the “auto”
selection tells the BD player to only turn on dynamic range
control if information embedded in the TruHD sound track
tells it to do so.
Center Speaker:
•
If the front speakers have been set to small, the center
speaker can only be set to ‘Small’ or ‘Off’.
•
Setting a speaker to ‘off’ will result in no sound being
delivered to that speaker.
Subwoofer:
Stereo Downmix:
•
If you don’t know the crossover frequency of your
subwoofer, consult the manual for your speaker
system.
Select whether to downmix the multi-channel audio into
fewer channels.
•
Auto — Downmixes the multi-channel audio into the
specific stereo that the connected equipment supports.
Surround Left & Right Speakers:
•
By setting the left surround speaker’s size, the right
surround speaker’s size is automatically changed to
match.
If the front speakers have been set to small, the surround
speakers can only be set to ‘Small’ or ‘Off’.
•
Stereo (LoRo) — Downmixes the multi-channel audio
into two channel stereo. Choose when the Blu-ray disc
player is connected to the equipment that does not
support virtual surround function such as Dolby Pro
Logic.
•
•
Surround Encoded (LtRt) — Downmixes the multi-
channel audio into surround compatible stereo. Choose
when the Blu-ray disc player is connected to the
equipment that supports virtual surround function such
as Dolby Pro Logic.
Rear Left & Right Speakers:
•
By setting the left rear speaker’s size, the right rear
speaker’s size is automatically changed to match.
•
If the front speakers have been set to small, the rear
speakers can only be set to ‘Small’ or ‘Off’.
4. Use
/
/
/
to move the highlight box to the Test
button on the bottom, then press OK. A message will
appear.
Speaker Setting
5. Press
/
to choose the desired audio signal.You can
Once the speakers are connected to the system and properly
configured, you can check to verify that the connections
to the speakers are correct by running an audio speaker
test.
select between Pink, 1kHz Sine and White.
6. Press OK to begin the speaker test.The audio signal will
be sent to a different speaker every approximately every
two seconds.The audio test will highlight which speaker
is supposed to be getting the sound on the screen.
To run this test, follow the instructions described as below:
7. To stop the audio test, press one of the
buttons.
/
/
/
1. In the main menu of Settings, press button, then use
/
button to select Speaker, then press OK.
8. Press or RETURN to go to the previous menu.
Note: This setup menu item has no effect unless:
•
•
If you have selected ‘Bitstream Mixed’ in the audio
menu, these menu choices will have no effect. (Each
channel’s full audio spectrum will be sent to each speaker,
regardless of the speaker size selected)
If you don’t know the type of speakers attached to your
surround sound system, consult the manual for your
speaker system.
2. Use
/
/
/
to highlight the desired speaker, then
press OK to enter.
3. Press to choose the desired audio signal, and then
/
press OK to confirm.
Front Left & Right Speakers:
•
By setting the front left speaker’s size, the front right
speaker’s size is automatically changed to match.
•
The front speakers can not be turned off. They can only
be set to ‘Small’ or ‘Large’.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the Function Settings
Notes:
Language Setting
•
•
Not all languages are available on all discs.
Some discs do not let you select the subtitle language
using your player’s menu.Instead, you have to select the
subtitle language from the disc setup menu (the menu
that appears after you insert the disc).
1. In the main menu of Settings, press
Language, and then press OK.
/
to select
•
You can also select the subtitle language from the subtitle
menu in the on-screen menu.
Language
OSD
English
English
Auto
Parental Control
Menu
Audio
Subtitle
1. In the main menu of Settings, press , then press
/
to select Parental, and then press OK.
None
Parental
Parental Country
Parental Control
Parental Level
USA
Off
1 [Kid Safe]
2. Press
then press OK.
/
to select OSD, Menu, Audio or Subtitle, and
Parental Password
3. Use
/
to select your preferred language, and then
press OK to confirm your selection.
4. Press to go to the previous menu.
OSD:
This option enables you to select the on-screen menu
language.
2. Press
3. Use
OK to confirm your selection.
/
to select an option, and then press OK.
to select the desired option, and then press
/
Menu:
This option lets you to select the disc menu language.
4. Press to go to the previous menu.
Notes:
Note: If Parental Control was previously turned On, you will
be prompted to enter the parental control password before
being allowed to change these settings. (See “Turning
parental control on or off” on page 34 for details.)
•
•
Not all languages are available on all discs.
Most discs only have one menu language.
Audio:
You can choose the audio language from this option to your
preference.
Selecting the parental country
Notes:
Parental Country is fixed in USA.
•
•
Not all languages are available on all discs.
Some discs do not let you select the audio language
using your player’s menu.Instead, you have to select the
audio language from the disc setup menu (the menu that
appears after you insert the disc).
Turning parental control on or off
1. In the main menu of Settings, press , then press
/
to select Parental, and then press OK.
Subtitle:
2. Press
3. Press
/
/
to select Parental Control, then press OK.
to select On or Off, then press OK.
You can customize your preferred subtitle language in this
option.
4. Press to go to the previous menu.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
Customizing the Function Settings
Setting the parental control level
System Setting
1. In the main menu of Settings, press , then press
/
to select Parental, and then press OK.
1. In the main menu of Settings, press button, then use
/
button to select System, then press OK.
2. Press
/
to select Parental Level, then press OK.
to select the rating level you want to block,
3. Press
/
then press OK. The rating and all higher ratings will be
blocked.You can select:
System
•
•
•
•
•
•
1 [Kid Safe] — Suitable for all children.
2 [G] — General audiences.
Optical Disc Auto Play
Enable
Time Zone
EST (GMT-05:00)
5 Minutes
Off
Screen Saver Duration
CEC Support
3 [PG] — Parental guidance suggested.
4 [PG-13] — Not suitable for anyone under 13.
5 [PG-R] — Parental guidance recommended.
Update Via Network
Restore factory defaults
6 [R] — Not suitable for anyone under 17 unless
supervised by a parent or adult guardian.
•
•
7 [NC-17] — Not suitable for anyone under 17.
8 [Adult] — All BDs and DVDs can be played.
4. Press to go to the previous menu.
2. Press
3. Use
OK to confirm.
/
to select an option, and then press OK.
/
to select the desired setting, and then press
Setting the parental control password
1. In the main menu of Settings, press , then press
/
4. Press to go to the previous menu.
to select Parental, and then press OK.
Optical Disc Auto Play:
2. Press
/
to select Parental Password, then press
OK.
If Enable is selected, it will load data and play back
automatically when you insert a Blu-ray disc.When Disable
is selected and if you insert a Blu-ray disc, the disc you can
select will be displayed on the Settings menu.
3. Enter a 4-digit number for the parental password, then
use to highlight Ok, and then press OK to confirm.
If you forget your password, reset your player to the
factory defaults. For more information, see “Restore
factory defaults” on page 35.
Time Zone:
This option allows you to select the desired time zone.
4. Press to go to the previous menu.
Screen Saver Duration:
This Blu-ray disc player has a screen saver feature that turns
the screen black when your player is inactive.You can set the
interval time you want your player to wait before activating
the screen saver.
Note: The unit shuts down automatically in about thirty
minutes if it remains idle and no activities are made.
CEC Support:
This option is used to allow the TV remote control to control
certain functions of the Blu-ray disc player; and for the Blu-
ray player to control certain functions of the TV.
On: Allow mutual control of devices through HDMI.
Off: Do not allow CEC control.
Notes:
•
Not all TVs are compatible with your Blu-ray disc
player.
•
The default setting is Off. Select On if CEC control is
necessary.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the Function Settings
Update Via Network:
This option displays the required storage space if the BD player is connected to internet for upgrade.
For detailed upgrade operation, please refer to “UpgradingYour Player’s Firmware” on this page.
Restore factory defaults:
Choose one of the following 7 options, then press OK to pop up a dialog box, choose Ok in the box, and then press OK
to confirm.
To apply the deactivation, please plug off the player after operating deactivation.
Actions
Response
Restore factory settings and deactivate All settings (including Parental Password) will be restored to the factory
all connected applications
defaults and all connected applications will be deactivated.
Restore factory settings
Restores all settings (including Parental Password) to the factory
defaults.
Deactivate all connected applications
Deactivates all connected applications (Netflix / Pandora / Blockbuster
/ VUDU)
Deactivate Netflix
Deactivate Pandora
Deactivate Vudu
Deactivates the connected Netflix application
Deactivates the connected Pandora application
Deactivates the connected VUDU application
Deactivates the connected Blockbuster application
Deactivate Blockbuster
Upgrading Your Player’s Firmware
The company that produced this player may occasionally offer upgrades to the player’s software.
Automatic upgrades over the Internet
1. Make sure that your player is successfully connected to the Internet.If new software is available, you will see a message
prompting you whether to update your firmware.
2. If you want to update the player’s firmware, use
/
to highlight “OK”, and then press OK. The software will begin
downloading, and a status bar will appear on the TV screen.
3. Once the update is complete, a message will appear indicating that the player will turn itself off and on.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
Customizing the Function Settings
Network Connection Setting
Wired IP Settings
Link Status
Link up
MAC Address
IP Mode
00:23:18:75:b1:2b
Dynamic
1. Press
/
to select Network in stop mode, then press
button,
IP Address
Subnet Mask
Gateway
128.60.3.31
255.255.0.0
128.60.1.1
128.60.1.41
128.60.1.42
I. If no Ethernet cable is connected to the ETHERNET
jack on the back of your player, a screen similar to the
following appears:
Primary DNS
Secondary DNS
Wireless
Apply
Cancel
Network Test
Network List
WiFi Protected Setup (WPS)
Manual
3. Press
/
to select an IP mode.You can select:
• Off — Disables the network interface.
• Manual — Lets you manually configure network settings,
such as IP address, subnet mask, and gateway settings.
• Dynamic — Uses DHCP to automatically obtain an IP
address.
IP Settings
For detailed operations, refer to the “Configuring a
wireless Internet connection”.
4. Press
/
/
/
to highlight NetworkTest, and press
OK to test your network connection.
5. Press or RETURN to go to the previous menu.
II. If a wired connection is made to your player, a screen
similar to the following appears:
Configuring a wireless Internet connection
Wired IP Settings
Link Status
MAC Address
IP Mode
Link up
This section describes how to configure the BD player for
accessing the internet via aWiFi connection.The procedure
for connecting to a wireless network depends on various
network parameters. Read the following configuration
methods to determine which instructions to use to connect
to your network.
00:23:18:75:b1:2b
Dynamic
IP Address
Subnet Mask
Gateway
128.60.3.31
255.255.0.0
128.60.1.1
128.60.1.41
128.60.1.42
I. Connection to the wireless Network which you
select
a. Connecting to an Unencrypted Wireless Network
b. Connecting to an Encrypted Wireless Network
Primary DNS
Secondary DNS
Apply
Cancel
Network Test
II. Connection to the wireless Network using Wi-Fi
Protected Setup (WPS)
a. Connecting to a Wireless Network Using WPS Pushbutton
b. Connecting to a Wireless Network Using WPS PIN
Refer to the “Configuring a wired Internet connection”
for details.
III.Connection to the wireless Network using Manual
IP Configration
Notes:
•
“Wireless” and “Wired” are optional and do not appear
at the same time. Normally, “Wireless” is shown without
wired connection.While using a wired Internet connection,
“Wireless” is disabled and “Wired” is activated.
Description of the Wireless Network List Display
Choosing “Network List” in the wireless network setup
menu will cause a list of available WiFi networks to appear,
as shown below:
Configuring a wired Internet connection
Network List
a
WiFi
WiFi
WiFi-me*
Panda
1. Press
/
to select Network in stop mode, then press
button to enter the following screen:
b g n
If the network connection is active, Link Up appears next
to Link Status. If the network connection is not active,
Link Down displays next to Link Status.
dlink_media
NTGR 11g
Airport_SN
a
WiFi
WiFi
WiFi
b g
b g
2. Press
/
to select IP Mode, then press OK.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the Function Settings
The symbols that might appear next to each listed wireless
network in the network list are as follows:
1. In the “Wireless” menu, press
/
to select Network
List, then press OK. A list of existing wireless networks
near the BD player will appear (It may take several
seconds for this list to be created). For example:
Category
Icon
Definition
Connected
When the BD player is turned on, it
will connect to the wireless network
displaying this symbol. Typically,
this is the last wireless network
connected before powering down.
Network List
a
WiFi
WiFi
WiFi-me*
Panda
b g n
Indicates that the BD Player is cur-
rently connected to this network.
*
dlink_media
NTGR 11g
Airport_SN
a
WiFi
WiFi
WiFi
Saved
The wireless network properties
have been saved in the BD player’s
memory.
b g
b g
Wireless
Security
The wireless network data is not
encrypted.
2. Press
press OK to confirm.
/
to select the desired wireless network, and
The wireless network data is
encrypted; a ‘security key’ must be
entered so that the BD player can
share data over the network.
a. If the BD player is connected to an Unencrypted
Wireless Network, a menu similar to the following will
appear:
The wireless network data is en-
crypted; the encryption scheme is
not supported by the BD player.
WiFi-me
Wireless
Protocol
The wireless network supports
802.11a
Connect
WPS Pin
Cancel
a
b
g
n
The wireless network supports
802.11b
Name and Password are case-sensitive
3. Press
/
to highlight Connect, and press OK. If the
icon and a message
The wireless network supports
802.11g
wireless network is functioning,
“Connection to XXX...Success” will appear on the TV.
The wireless network supports
802.11n
4. Press OK to close the message. The BD disc player is
now connected to the network. From now on, when you
turn on the player, it will automatically connect to the
network; there is no need to repeat these steps again.
The wireless router supports the
WPS standard.
Signal
Strength
Note: If you do not see this message, the BD player was
not able to connect to the network.
Strong Signal
Good Signal
Medium Signal
Weak Signal
No Signal
b. If the BD player is connected to an Encrypted
Wireless Network, a menu similar to the following will
appear:
WiFi-me
Password
Connect
WPS Pin
Cancel
I. Connection to the wireless Network which you
select
Press ENTER to open keyboard
Password is case-sensitive
Wireless
3. Press ENTER to activate the on-screen keyboard.
Carefully enter the network password by using the
to highlight the desired letter on the keyboard,
and then pressing OK. (If you make a mistake, use the
backspace key to erase the mistake.)
/
Network List
/
/
WiFi Protected Setup (WPS)
Manual
IP Settings
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
Customizing the Function Settings
3. Press the WPS button on the top of your router.
Done
1 2 3 4 5 6 7 8 9 0
4. Once you see “Success” on the button at the bottom of
the screen, the BD player is connected to the router.
p
o
q w e r t y u
i
Note:If you do not see this message, the BD player was not
able to connect to the network. Repeat steps 1-4 again.
a s d f g h j k l ;
b. If the BD player is connected to a Wireless Network
Using WPS PIN:
, .
[ ]
z x c v b n m
/
'
Space
- =
`
\
2. Press
/
to select Network List, then press OK. A
list of existing wireless networks near the BD player will
appear (It may take several seconds for this list to be
created). For example:
Done
4. Use
/
/
/
to highlight
on the upper-right corner
of the keyboard, and press OK to remove the keyboard
from the screen.
Network List
5. Use
to highlight Connect, and press OK. If the
a
WiFi
WiFi
WiFi-me*
Panda
wireless network is functioning,
“Connection to XXX...Success” will appear on the TV.
icon and a message
b g n
6. Press OK to close the message. The BD player is now
connected to the network. From now on, when you turn
on the player, it will automatically connect to the network;
there is no need to repeat these steps again.
dlink_media
NTGR 11g
Airport_SN
a
WiFi
WiFi
WiFi
b g
b g
Notes:
•
If you do not see this message, the BD player was not
able to connect to the network.
3. Press
press OK to confirm.
/
to select the desired wireless network, and
•
If the wireless network is encrypted using an
unsupported encryption (it appears in the network
list with an icon), you cannot connect to the network.
You must change the router’s encryption type before
proceeding.
4. Press
following screen will appear:
/
to highlight WPS PIN, and press OK. The
WiFi-me
II. Connection to the wireless Network using Wi-Fi
protected Setup(WPS)
Password
1. Press
/
to select Network in stop mode, then press
Connect
WPS Pin
Cancel
button to enter the following screen:
Press ENTER to open keyboard
Password is case-sensitive
Wireless
5. Press
and press OK.
/
to highlight connection method you desire,
Network List
WiFi Protected Setup (WPS)
Manual
6. Follow the on-screen message to continue operating the
connection.
IP Settings
III. Connection to the wireless Network using Manual
IP Configration
a. If the BD player is connected to a Wireless Network
Using WPS Pushbutton:
1. In the “Wireless” menu, press
then press OK.
/
to select Manual,
2. Press
/
to select WiFi Protected Setup (WPS), then
press OK.
Wireless
Network List
WiFi Protected Setup (WPS)
WiFi Protected Setup (WPS)
Manual
Please press the button on your router now
Network Name (SSID)
IP Settings
Cancel
2. Follow the on-screen message to continue operating the
connection.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Connected Applications
Some players are equipped with the capability to watch movies over the internet (from Blockbuster, Netflix or Vudu), or
to listen to Pandora internet radio.
Watching Movies with Netflix®
To use Netflix service, connect this player to your network,
and make the network settings if they are not finished yet.
1. Launching Netflix movie
In Home Menu, press
, and then press
/
to select Connected, then use
to highlight “Netflix”, and then
/
press OK to enter.
Video
4. Preparing Instant Queue
Settings
Blockbuster
Netflix
To play streaming video via Netflix service, Netflix player
needs to be activated. Read the instructions displayed on
your PC. Sign in to your Netflix account, if necessary. Enter
the activation code displayed on the TV screen.
Connected
Pandora
Vudu
Music
Now you can view Netflix streaming video.
After having activated Netflix player and prepared Instant
Queue, movies and TV episodes in your Instant Queue
appear on the TV screen. Select your desired one using
the remote control of the player. You can control Netflix
streaming video with the following keys of the remote control
of this player:
Pictures
2. Creating Netflix account
To start playing movie.
If you are not a Netflix Member:
To pause playback while in PLAY mode.
Select “no”. Read the instructions displayed on the TV
PC. Sign up to create your account, then select “I’m now
a member”.
To stop playing and return to a list of
movie titles.
To pause playing movie.
To start playing while in PAUSE mode.
To pause playing and open a list of
scenes. Pressing further proceeds to the
next scene.
To pause playing and open a list of
scenes. Pressing further proceeds to the
previous scene.
To stop playing and return to a list of
movie titles.
To pause playing and open a list of
scenes. Fast forward play starts.
If you are a Netflix Member:
Select “Yes”.
To pause playing and open a list of
scenes. Fast reverse play starts.
HOME MENU To stop playing and return to Home Menu.
3. Activating Netflix player
OK
To pause playing of Trick play screen
while in PLAY mode.
To play streaming video via Netflix service, Netflix player
needs to be activated. Read the instructions displayed on
your PC. Sign in to your Netflix account, if necessary. Enter
the activation code displayed on the TV screen.
To start playing the movie in case of dur-
ing Trick play screen.
Note:Resolution of video streamed from Netflix varies depending
on communication speed or bitrate of each content, etc.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
Using the Connected Applications
Watching Movies with BLOCKBUSTER®
This Blu-ray Disc Player enables you to use the following services provided by Blockbuster.
1. In Home Menu, press
2. Press , then press
/
to select Connected.
/
to highlight Blockbuster, and then press OK to enter Blockbuster main menu.
•
•
•
•
•
•
•
Movies : Display movies.
TV Shows : Display TV Shows.
Find : Search for a desired movie or TV show by entering it manually.
My Library : Display a title that you bought or rented.
My Favorites : Display a title that has been added to My Favorites.
Configure : Activate or deactivate the Blu-ray Disc Player.
Help : Get customer service contact information and check the current software version.
4. Use to select the Configure, then press OK.
/
/
/
5. Use the number buttons on the remote control to enter the activation code that is created by the web site, then use
to highlight Activate, and press OK to confirm.
When the Blu-ray Disc Player is activated, you will move to the Home page.
6. Press
7. Press
8. Press
9. Press
/
/
/
/
to select the Movies or TV Shows, then press OK.
to select the desired title, then press OK.
/
/
to select the Rent or Buy, then press OK.
to select the Submit Order, then press OK. If you want to play any of the titles that your bought, simply
click Play Now.
10.Press to go to the previous menu.
Watching Movies with VUDU™
Creating a VUDU account on your player
1. In Home Menu, press
2. Press , then press
/
to select Connected.
/
to highlight Vudu, and then press OK to confirm.
3. Follow the instructions to create an account, it will ask for an email address.
4. Enter YOUR email address using the keyboard that appears on the screen. VUDU will then display a message on the
TV “Sending you an email”.
Creating a VUDU account on your PC
1. VUDU will send you an email with a hyper-link; click on the link.
2. In the Vudu page that comes up on your PC’s browser after clicking the link, enter the e-mail and password of the
owner of the account.
3. VUDU will then display a message “Enabling your device to view movies.The email message on yourTV screen
will disappear when done”.
4. On your TV, you can now navigate to a Vudu movie, and ‘buy’ or ‘rent’ it.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Connected Applications
Listening to Music with PANDORA®
Using an existing Pandora account
1. In Home Menu, press
2. Press , then press
/
to select Connected.
to highlight Pandora, and then press OK to confirm.
/
3. Select “I have a Pandora account” from the option list.
4. Sign in with your test account.
Creating a new account on the BD player
1. In Home Menu, press
2. Press , then press
/
to select Connected.
to highlight Pandora, and then press OK to confirm.
/
3. Select “I am new to Pandora” from the option list.
4. You will be given an activation code. Use this activation code to generate a new account and link it to the BD player
using a PC.
Creating a new Pandora account on your PC
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Troubleshooting & Maintenance
Troubleshooting
If the unit does not perform properly when operated as instructed in this manual, check the unit, consulting the following
checklist.
Problem
Solution
No power
- Check if the AC cord is properly connected.
- Unplug the AC cord once, and wait for 5-10 seconds and then plug it in again.
No sound or picture
Distorted picture
- Check if the connected TV is turned on.
- Check if the connections are made securely and correctly.
- Check whether the connected TV or other device supports HDCP. (This unit will
not output a video signal unless the other device supports HDCP.)
- Check whether the output format of this unit (HDMI FORMAT) matches the
supported input format of other connected device.
- Sometimes a small amount of picture distortion may appear. This is not a
malfunction.
- Connect this unit directly to the TV. If the composite audio / video cables are
connected to a VCR, pictures may be distorted due to the copyright protection
system.
Completely distorted picture or black
/ white picture with BD / DVD
- Make sure the disc is compatible with this unit.
No sound or distorted sound
- Adjust the volume.
- Check if speakers are connected correctly.
- Check the HDMI connections.
- Check the settings in “Audio” menu.
Picture freezes momentarily during
playback
- Check the disc for fingerprints / scratches and clean with a soft cloth wiping from
center to edge.
- Clean the disc.
Disc cannot be played back
- Clean the disc.
- Ensure the disc label is facing up.
- Check if the disc is defective by trying another disc.
- Cancel the ratings control or change the control level.
- Insert a correct disc that can be played back on this unit.
SD Memory Card cannot be read
- The format of the card does not match that accepted by this unit or the card is not
compatible.
No return to start-up screen when
disc is removed
- Reset this unit by turning it off, then on again.
The unit does not respond to the
remote control
- Aim the remote control directly at infrared sensor window on the front panel.
- Reduce the distance to infrared sensor window.
- Replace the batteries in the remote control.
- Re-insert the batteries with their polarities (+ / - signs) as indicated.
Buttons do not work or the unit stops
responding
- To completely reset the unit, unplug the AC cord from the AC outlet for 5-10
seconds.
The unit does not respond to some
operating commands during playback
- Operations may not be permitted by the disc.
Refer to the instructions of the disc.
The unit cannot read BD / DVD/ CD
- Dew condensation may form inside the unit. Do not use this unit for at least a few
hours until its inside gets dry.
- Wipe the dirt off the disc or replace the disc.
Angle does not switch
- The angle cannot be switched for BD / DVD which do not contain multiple angles.
In some cases multiple angles are only recorded for specific scenes.
Playback does not start when the title
is selected
- Check the settings in “Parental” menu.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting & Maintenance
Problem
Solution
The password for rating level has
been forgotten
- If you forget your password, reset your player to the factory defaults and your
forgotten password will be cleared. For more information, see “Restore factory
defaults” on page 35.
Cannot connect to the network
- Check if the LAN cable connection is properly made.
- Turn on the modem or broadband router.
- Check if the broadband router and/or modem is correctly connected.
- Check the “Network Connection Setting”.
Cannot connect to the network while
my PC is connected to the network
- Check the content of your Internet service contract to see if your Internet service
provider prevents multiple terminals connecting at the same time.
Cannot use the BD-Live function
- Use an SD card with enough space.
The playback of BD-video or
download of data does not perform
properly
- Check if an SD Card is correctly inserted. Do not remove the card during playback
as some BD-videos require an SD Card during playback.
Notes
•
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this manual for details
on correct operations.
•
Some functions are prohibited on some discs.
Maintenance
Servicing
• Please refer to relevant topics on “Troubleshooting & Maintenance” before returning the product.
• If this unit becomes inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn
off, unplug the power plug, and please call our helpline to locate an Authorized Service Center.
Cleaning the cabinet
• Never use a solvent, thinner, benzene or alcohol to clean the unit. Do not spray insecticide liquid near the unit. Such chemicals
may discolor the surface or damage the unit.
Cleaning discs
• When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center to out. Do not wipe in a circular
motion.
• Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic
spray intended for analog records.
Cleaning the disc lens
• If this unit still does not perform properly although you refer to the relevant sections and to “Troubleshooting” in this manual, the
laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the
laser optical pickup unit.
Disc handling
• Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.
• Always store the disc in its protective case when it is not used.
• Note that discs with special shapes (heart-shaped discs, octagonal discs, etc.) cannot be played back on this unit. Do not
attempt to playback such discs, as they may damage the unit.
IR signal check
• If the remote control is not working properly, you can use a digital camera (including a cellular phone with built-in camera) to
see if it is sending out an infrared signal.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Glossary
Analog Audio
DNS Server
An electrical signal that directly represents sound. Compare A server which translates Internet domain names into IP
this to digital audio which can be an electrical signal, but is an addresses.
indirect representation of sound.
Dolby Digital
Aspect Ratio
The system to compress digital sound developed by Dolby
The width of a TV screen relative to its height.
Laboratories. It offers you sound of stereo (2ch) or multi-
Conventional TVs are 4:3 (in other words, the TV screen is channel audio.
almost square); widescreen models are 16:9 (the TV screen is
almost twice as wide as it is high).
Dolby Digital Plus
Dolby Digital Plus is the next generation digital audio
compression technology developed as an extension to Dolby
AVCHD
AVCHD is a new format for high definition video camcorders Digital. Blu-ray Disc supports 7.1 multi-channel surround
which can record and play high-resolution HD images.
sound output.
BD-Java
Dolby TrueHD
With some BD which support Java applications, you can enjoy Dolby TrueHD is a lossless coding technology developed for
the interactive functions such as games or interactive menus.
next generation optical discs. Blu-ray Disc supports 7.1 multi-
channel surround sound output.
BD-Live
DTS
BD-Live is a BD-video (BD-ROM version 2 Profile 2.0/Profile
1.1) which contains new functions (e.g. Internet connection), in DTS is a multi-channel surround sound system. By connecting
addition to the BONUSVIEW function.
to DTS decoder, you can enjoy movie dynamic and realistic
sound like movie theater. DTS surround sound technologies
were developed by DTS, Inc.
Blu-ray 3D
Blu-ray 3D is a BD-video (BD-ROM version 3 Profile 5.0)
which contains 3D view function, in addition to the BD-Live/
BONUSVIEW function.
DTS-HD
DTS-HD is a lossless coding technology developed as an
extension of the original DTS Coherent Acoustics format. Blu-
ray Disc supports 7.1 multi-channel surround sound output.
Blu-ray Disc (BD)
Blu-ray Disc is a next generation optical video disc which is
capable of storing much more data than a conventional DVD
Gateway
is. The large capacity makes it possible to benefit from the IP Address of the electronic devices (such as router) which
features such as high-definition videos, multi-channel surround provide Internet access.
sounds, interactive menus and so on.
HDMI (High-Definition Multimedia Interface)
Chapter
A digital interface between audio and video source. It can
Just as a book is split up into several chapters, a title on a BD- transmit component video, audio, and control signal with one
video or DVD-video is usually divided into chapters.
cable connection.
Hub
Component Video Output
A device used for connecting multiple device to the network.
Each signal of luminance (Y) and component (PB/CB, PR/CR)
is independent to output so that you can experience picture
Color as it is.
Also, due to compatibility with progressive video (525p/480p),
you can experience higher-density picture than that in interlace
(525i/480i).
IP Address
A set of numbers which are assigned to devices participating
in a computer network.
JPEG (Joint Photographic Experts Group)
Digital Audio
JPEG is a method of compressing still picture files. You can
copy JPEG files on BD-RE/-R, DVD-RW/-R, CD-RW/-R or SD
Memory Card from a computer and play back the files in this
unit.
An indirect representation of sound by numbers. During
recording, the sound is measured at discrete intervals (44,100
times a second for CD audio) by an analog-to-digital converter,
generating a stream of numbers. On playback, a digital-to-
analog converter generates an analog signal based on these
numbers.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
LAN (Local Area Network)
Virtual Package
A group of computer networks covering a small area like a The function which copies data to other media (local storage)
company, school or home.
from the Internet and play the secondary video, secondary
audio and the subtitle at the same time. The method of the
playback varies depending on discs.
Local Storage
A storage area of sub contents for playing virtual packages on
BD-video.
Windows Media™ Audio
Windows Media™ Audio is the audio compressing technology
developed by Microsoft.You can copy Windows Media™ Audio
files on BD-RE/-R, DVD-RW/-R, CD-RW/-R or SD Memory
Card from a computer and play them back on this unit.
MP3 (MPEG audio layer 3)
MP3 is a method of compressing files.You can copy MP3 files
on BD-RE/-R, DVD-RW/-R, CD-RW/-R or SD Memory Card
from the computer and play back the files on this unit.
x.v.Color
“x.v.Color” is a promotion name given to the products that have
the capability to realize a wide color space based on the xvYCC
specifications and is a trademark of Sony Corporation.
PCM (Pulse Code Modulation)
The most common system of encoding digital audio, found
on CD and DAT. Excellent quality that requires a lot of data
compared to formats such as Dolby Digital and MPEG audio.
For compatibility with digital audio recorders (CD, MD and
DAT) and AV amplifiers with digital inputs, this unit can convert
Dolby Digital, DTS, and MPEG audio to PCM.
Proxy Server
Proxy server is a server which acts as an intermediary between
a workstation user and the Internet to ensure security.
Region Code
Regions associate discs and players with particular areas
of the world. This unit will only play back discs that have
compatible region codes.You can find the region code of your
unit by looking on the rear panel. Some discs are compatible
with more than one region (or all regions).
Router
A
networking device which distinguishes the IP address
assigned to each device and routing and forwarding information
in the computer network.
Sampling Frequency
The rate which sound is measured by a specified interval to
turn into digital audio data. The numbers of sampling in one
second defines as sampling frequency.The higher the rate, the
better the sound quality.
Subnet Mask
A mask which is used to determine what subnet an IP address
belongs to.
Title
A collection of chapters on BD-video or DVD-video.
Track
Audio CD use tracks to divide up the content of a disc.The BD-
video or DVD-video equivalent is called a chapter. See also
“Chapter”.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Specifications
General
Signal system
NTSC color
Power requirements
Power consumption
Dimensions (width x height x depth)
Weight
120 V AC, 60 Hz
23 W
430 x 63.5 x 209.7 mm
1.77 kg
Operating temperature
Operating humidity
41°F (5°C) to 95°F (35°C)
Less than 80 % (no condensation)
Terminals
Video output
RCA jack
1 Vp-p (75Ω)
Y: 1 Vp-p (75Ω)
Component video output
RCA jack x 3
PB/CB: 700 mVp-p (75Ω) PR/CR: 700 mVp-p (75Ω)
Video: 480i, 480p, 720p, 1080i
HDMI output
HDMI jack x 1
Video: 480i, 480p, 720p, 1080i, 1080p, 1080p/24F / Audio
Audio output (Analog)
RCA jack x 2
L/R: 2 Vrms (output impedance: less than 1kΩ)
Digital connector
Audio output (Digital)
Optical jack x 1
Multi channel audio output
RCA jack x 8
All channels: 2 Vrms (output impedance: less than 1kΩ)
USB terminal x 1
LAN terminal
5V
500mA
100BASE-T
The specifications and design of this product are subject to change without notice.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited United States Warranty
Digital Audio Video (“DAV”) Product - Exchange Warranty
Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original consumers in the United
States.
THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING
THIS DAV PRODUCT AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR
TRANSFEREE.
DAV PRODUCTS PURCHASED IN THE U.S.A. AND USED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT
LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.
DAV PRODUCTS PURCHASED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND
MEXICO, AND USED IN THE U.S.A., ARE NOT COVERED BY THESE WARRANTIES.
through simultaneous use of this DAV Product and connected
equipment;or to units that have been modified or had the serial
number removed, altered, defaced, or rendered illegible.
(6) This warranty does not cover Product sold AS IS orWITH ALL
FAULTS.
Limited Warranty
TACP warrants this DAV Product and its parts against defects in
materials or workmanship for a period of ninety (90) days after
the date of original retail purchase.
DURINGTHISPERIOD,TACPWILLEXCHANGEADEFECTIVE
DAV PRODUCT WITH A NEW OR REFURBISHED DAV
PRODUCT WITHOUT CHARGE TO YOU. DURING THE
PERIODTHAT COMMENCES ONTHE DATETHAT IS NINETY
ONE (91) DAYS AFTER THE DATE OF ORIGINAL RETAIL
PURCHASE AND ENDS ON THE DATE THAT IS THREE
How to Obtain Warranty Services
If, after following all of the operating instructions in this manual
and checking the section “Before Calling Service Personnel,”
you find that service is needed:
HUNDRED SIXTY FIVE (365) DAYS AFTER THE DATE OF (1) For instructions on how to obtain warranty service for
ORIGINAL RETAIL PURCHASE, TACP WILL EXCHANGE A
DEFECTIVE DAV PRODUCTWITH A NEW OR REFURBISHED
DAV PRODUCT FOR A FEE.
your DAV Product under the TACP DAV Product Warranty
Exchange Program, contact TACP’s Consumer Solutions
Center toll free at 1-800-631-3811.
(2) You must include the original bill of sale (or a copy of the
original bill of sale) or other proof of purchase along with
the entire DAV Product when sending the DAV Product to
the TACP Warranty Exchange Center specified by TACP’s
Consumer Solutions Center. You are responsible for all
inbound transportation and insurance charges for the DAV
Product to the TACP Warranty Exchange Center.
Rental Units
The warranty for DAV Product rental units begins on the date
of the first rental or thirty (30) days after the date of shipment
to the rental firm, whichever comes first.
Commercial Units
DAV Products sold and used for commercial purposes have a
limited warranty for all parts and labor, which warranty begins
on the date of original retail purchase and ends on the date that
is ninety (90) days thereafter.
For additional information, visit TACP’s website:
ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE
OF THE U.S.A., INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF
THE LIMITED WARRANTIES SET FORTH ABOVE. WITH THE
EXCEPTION OF ANY WARRANTIES IMPLIED BY THE LAW
OF ANY STATE OF THE U.S.A. AS HEREBY LIMITED, THE
FOREGOINGWARRANTY IS EXCLUSIVE AND IN LIEU OF ALL
OTHER WARRANTIES, GUARANTEES, AGREEMENTS, AND
OF ALL OTHERWARRANTIES, GUARANTEES, AGREEMENTS,
AND OR REPLACEMENT OF ANY PARTS. IN NO EVENT SHALL
TACP BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES (INCLUDING, BUT NOT LIMITEDTO, LOST PROFITS,
BUSINESS INTERRUPTION, OR MODIFICATION OR ERASURE
OF RECORDED DATA CAUSED BY USE, MISUSE OR INABILITY
TO USE THIS DAV PRODUCT).
Owner’s Manual and Product Registration Card
Read this owner’s manual thoroughly before operating this DAV
Product. Complete and mail the enclosed product registration
com/service as soon as possible. By registering your DAV
Product you will enable TACP to bring you new products
specifically designed to meet your needs and help us to contact
you in the unlikely event a safety notification is required under
the U.S. Consumer Product Safety Act. Failure to complete
and return the product registration card does not diminish your
warranty rights.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO FOLLOWING
CONDITIONS:
(1) You must retain your bill of sale or provide other proof of
purchase.
(2) All warranty servicing of this DAV Product must be made pursuant
to the TACP DAV Product Warranty Exchange Program.
(3) The warranties fromTACP are effective only if the DAV Product
is purchased and operated in the Continental U.S.A.or Puerto
Rico.
(4) Labor service charges for set installation, setup, adjustment
of customer controls, and installation or repair of antenna
systems are not covered by this warranty. Reception
problems caused by inadequate antenna systems are your
responsibility.
(5) Warranties extend only to defects in materials or workmanship
as limited above, and do not extend to any DAV Product or
parts that have been lost or discarded by you or to damage to
the DAV Product or parts caused by fires, misuse, accident,
Acts of God ( such as lightning or fluctuations in electric
power), improper installation, improper maintenance, or use in
violation of instructions furnished byTACP;use or malfunction
No person, agent, distributor, dealer, or company is authorized
to change, modify, or extend the terms of these warranties in any
manner whatsoever. The time within which an action must be
commenced to enforce any obligation of TACP arising under the
warranty or under any statute or law of the United States or any
state thereof is hereby limited to ninety (90) days from the date you
discover, or should have discovered, the defect.This limitation does
not apply to implied warranties arising under state law.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER RIGHTSWHICH MAYVARY FROM
STATE TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A.
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, WHEN AN ACTION MAY BE BROUGHT,
OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE PROVISIONS
MAY NOT APPLY TOYOU UNDER SUCH CIRCUMSTANCES.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Disclaimer
I. HEALTH/SAFETY-RELATED
IMPORTANT SAFETY INFORMATION CONCERNING 3D VIEWING
• If you or any viewer experiences the following symptoms or any other discomfort from viewing 3D video images, stop viewing
and contact your health care provider:
Convulsions
Altered vision
Eye Strain
Eye or muscle twitching
Involuntary movements
Nausea/Vomiting
Fatigue
Loss of awareness
Disorientation
Dizziness
Headaches
• Some viewers may experience a seizure or blackout when exposed to certain flashing images or lights contained in certain
3D television pictures or video games. Anyone who has had a seizure, loss of awareness, or other symptom linked to an
epileptic condition, or has a family history of epilepsy, should contact a health care provider before using the 3D function.
• If you feel eye fatigue or other discomfort from viewing 3D video images, stop viewing and take a rest until the condition is
eliminated.
• Due to the possible impact on vision development, viewers of 3D video images should be age 6 or above. Children and
teenagers may be more susceptible to health issues associated with viewing in 3D and should be closely supervised to avoid
prolonged viewing without rest.
• Avoid use of the 3D function when under the influence of alcohol.
• Watching the screen while sitting too close for an extended period of time may cause eye strain. Consult your display manual
to determine the ideal viewing distance.
• Viewing in 3D may cause dizziness and/or disorientation for some viewers.Therefore, to avoid injury do not place your player
or display near open stairwells, balconies, or wires and do not sit near objects that could be broken if accidentally hit.
• Carefully read instructions provided with your display and/or 3D glasses before 3D viewing.
II. PERFORMANCE RELATED
• This product is designed to playback Blu-ray discs that comply with the 3D specifications of Blu-ray Disc Association. It is not
compatible with other 3D specifications.
• 3D capable display, 3D eyewear and High Speed HDMI cable (all sold separately) required for playback and viewing 3D
content.
• If you route your signal through an AV receiver or other video distribution device they must be 3D capable to support 3D
viewing. Viewing HD content and up-converting DVD content may require an HDCP capable input on your display device.
• While up-converting DVD video content may result in a picture that appears to be near HD quality, results may vary depending
on content, display and settings.
• 1080p capable display required for viewing content in 1080p.
• 1080p/24 fps encoded content and an HD display capable of accepting a 1080p/24Hz signal required for viewing 1080p/24
fps content.
• Performance of interactive and/or network features may vary due to disc design or content, and may also require an always-
on broadband internet connection. Firmware update may be required for some interactive and/or network features. Some
features may require additional bandwidth.
• BD-Live™ may require an SD or SDHC card or USB memory with available storage capacity of at least 1GB (sold
separately).
• VUDU™, Netflix®, BLOCKBUSTER® on Demand, Pandora® and other internet services are available only in the United
States, and are not provided by Toshiba, may change or be discontinued at any time and may be subject to internet service
provider restrictions.
• Toshiba makes no warranties, representations, or assurances about the content, availability or functionality of third-party
content or services. Use of third party internet services may require the creation of a separate account through a computer
with internet access and may require payment of one-time and/or recurring charges. Not all services may be available on or
compatible with these products.
• For Dolby® TrueHD and DTS-HD Master Audio | Essential™ playback, content encoded in Dolby® TrueHD and DTS-HD
Master Audio | Essential™ format required. Supported file types: JPEG, MP3, WMA, and AVCHD. Some recordable media,
cards or files may not be supported. Deep Color feature as specified in HDMI specification requires compatible Deep Color
capable HD display and/or device. Use of HDMI-CEC requires an HDMI-CEC compatible display device. Depending on the
specifications of your display device, some or all HDMI-CEC functions may not work even if your display device is HDMI-CEC
compatible.
• Products do not play HD DVD discs.
• Some features subject to delayed availability.
• Because the Blu-ray format and 3D specifications use new technologies, certain disc, content, connection and other
information on the availability of firmware updates that may resolve your problem, or contact Toshiba Customer Solutions.
• This product includes technology owned by Microsoft Corporation and can not be used or distributed without a license from
Microsoft Licensing, GP.
• This product contains technology subject to certain intellectual property rights of Microsoft. Use or distribution of this
technology outside of this product is prohibited without the appropriate license(s) from Microsoft.
• While every effort has been made at the time of publication to ensure the accuracy of the information provided herein,
product specifications, configurations, system/component/options availability are all subject to change without notice.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
END USER LICENSE AGREEMENT
This End User License Agreement (“EULA”) is a legal agreement between you and Toshiba Corporation (“Toshiba”) with regard
to the copyrighted Software provided with this EULA. Use of any software and related documentation (“Software”) provided
with a Toshiba Blu-ray Player, or made available by downloading or otherwise to you by Toshiba in whatever form or media,
will constitute your acceptance of these terms, unless separate terms are provided by the software supplier or Toshiba in the
documentation accompanying the Toshiba Blu-ray Player or otherwise, in which case certain additional or different terms may
apply. If you do not agree with the terms of this EULA, do not use, download, install or copy the Software. If you wish to return
a complete Blu-ray Player system (hardware and software), contact the retailer where you purchased the Blu-ray Player, and
comply with the retailer’s standard return policies and procedures.
Article 1 Definition
The Software means all programs contained in the Toshiba Blu-ray Player.The copyright of the Software belongs to Toshiba and/
or its suppliers, including BSQUARE Corporation and/or its suppliers. The Software is protected by copyright laws, Universal
Copyright Convention, and other laws and conventions related to intellectual property rights. The content of the Software and
manual is subject to change by Toshiba without notice.
Article 2 License Grant and Use Conditions
Toshiba grants to you a personal, non-transferable and non-exclusive right to use the copy of the Software in accordance with
this EULA. You may permanently transfer all of your rights under this EULA, provided you transfer complete Blu-ray Player
together with all of the Software, you retain no copies, and the recipient agrees to the terms of this EULA. If the Software is an
upgrade version, any transfer must include all prior versions of the Software. For maintenance purposes, you may update the
version of the Software only for the Blu-ray Player that is owned by you.
Article 3 Prohibited Uses
Unless otherwise expressly provided in this EULA or the product manual accompanying the Toshiba Blu-ray Player:
3.1. You may not copy the Software, in whole or in part, without express written permission by Toshiba and/or its
suppliers.
3.2. You may not assign, resell, distribute or sublicense the Software or a copy of the Software.
3.3. You may not create, assign, resell, or sublicense secondary works of the Software without permission.
3.4. You may not modify, analyze, reverse engineer, decompile or disassemble any part of the Software.
3.5. You may not combine or incorporate the Software with or into any other application.
3.6. You may not print the Software.
Article 4 Disclaimer
4.1. THE HARDWARE PRODUCT LIMITED WARRANTY IS SET FORTH IN THE DOCUMENTATION ACCOMPANYING THE
HARDWARE PRODUCT.
4.2. THE SOFTWARE IS PROVIDED “AS-IS” AND “AS-AVAILABLE,” WITHOUT WARRANTIES OF ANY KIND. ALL
WARRANTIES AND CONDITIONS, EXPRESS OR IMPLIED, CONTRACTUAL OR STATUTORY, INCLUDING BUT NOT
LIMITEDTO, ANY IMPLIEDWARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,TITLE
OR NON-INFRINGEMENT ARE HEREBY WAIVED BYYOU AND DISCLAIMED BY TOSHIBA.THIS EULA REPRESENTS
THE SOLE AND EXCLUSIVE OBLIGATION OF TOSHIBA AND ITS SUPPLIERS WITH RESPECT TO THE SOFTWARE.
Article 5 Limitation of Liability
TO THE MAXIMUM EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT SHALL TOSHIBA AND/OR
ITS SUPPLIERS BE LIABLE FOR PERSONAL INJURY, OR ANY INCIDENTAL, SPECIAL, INDIRECT, PUNITIVE OR
CONSEQUENTIAL DAMAGES WHATSOEVER, INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS,
LOSS OF DATA, BUSINESS INTERRUPTION, OR ANY OTHER COMMERNCIAL DAMAGES OR LOSSES, ARISING OUT
OF OR RELATED TO YOUR USE OR INABILITY TO USE THE SOFTWARE, HOWEVER CAUSED, REGARDLESS OF THE
THEORY OF LIABILITY (CONTRACT, TORT, OR OTHERWISE) AND EVEN IF TOSHIBA AND/OR ITS SUPPLIERS HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME JURISDICTIONS DO NOT ALLOW THE LIMITATION OF
LIABILITY FOR PERSONAL INJURY, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES; THEREFORE, THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU UNDER SUCH CIRCUMSTANCES. THE AGGREGATE LIABILITY OF TOSHIBA AND
ITS SUPPLIERS IN CONNECTION WITH THE SOFTWARE, REGARDLESS OF THE FORM OF ANY LEGAL ACTION OR
PROCEEDING, SHALL BE LIMITED TO DIRECT DAMAGES NOT TO EXCEED THE AMOUNT PAID FOR THE TOSHIBA BLU-
RAY PLAYER.
Article 6 Export Control
Any export, directly or indirectly, of the Software in contravention of the United States Export Administration Regulations, or any
other applicable law, regulation, or order, is prohibited.
Article 7 Termination of License
In the event that you fail to comply with any of the terms and conditions contained herein, Toshiba shall have the right to
immediately terminate this Agreement without any notification to you. Upon termination of this Agreement, you shall cease all
use of the Software and destroy all copies, in whole and/or in part.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Article 8 Governing Law
This EULA is governed by the laws of Japan, without references to the conflict of laws principles. Any and
all disputes arising hereunder shall be resolved exclusively by the Tokyo District Court, Japan, and you hereby
consent to the exclusive jurisdiction of such court.
Article 9 Severability
If any provision of this EULA shall be held to be invalid, illegal or unenforceable, the validity, legality and enforceability
of the remaining provisions hereof shall not in any way be affected or impaired.
(C) 2001-2010 Toshiba Corporation
The Software contains Macromedia® [Flash®] [Flash Lite™] technology of Adobe Systems Incorporated.
Copyright© 1995-200[7] Adobe Systems Incorporated. All rights reserved. Macromedia, Flash, Macromedia
Flash, [and Macromedia Flash Lite] are trademarks or registered trademarks of Adobe Systems Incorporated in
the United States and other countries.
License information on the software used in the TOSHIBA BD player
This document is statement purpose only. Not concerned with operation of this product.
The software pre-installed in the TOSHIBA BD player consists of multiple, independent software components. Each software
component is copyrighted by TOSHIBA or a third party.
The TOSHIBA BD player uses software components that are distributed as freeware under a third-party end-user license
agreement or copyright notice (hereinafter referred to as a “EULA”).
Some EULAs require that the source code of the applicable component be disclosed as the condition for distributing the software
component in executable format. You can check the software components subject to such EULA requirements on the following
phone number:
Phone number: 1-800-631-3811
TOSHIBA provides a warranty for the TOSHIBA BD player you have purchased under conditions set forth by TOSHIBA.
However, some of the software components distributed under an EULA are made available for use by the user on the assumption
that they are not copyrighted or warranted by TOSHIBA or any third party. These software components are licensed to the user
free of charge and therefore not covered by any warranty within the scope of the applicable laws. These software components
are not subject to any copyrights or other third-party rights and are provided in “as is” condition without any warranty, whether
express or implied. “Warranty” here includes, but not limited to, an implied warranty for marketability or fitness for specific uses.
All risks associated with the quality or performance of these software components are assumed by the user. TOSHIBA shall not
be liable whatsoever for any cost of repair or correction or other incidental expense incurred in connection with a defect found in
any of these software components. Unless specified under the applicable laws or in a written agreement, a party who changes
or redistributes the software with consent from the copyright holders or based on the aforementioned licenses shall not be held
liable whatsoever for any loss arising from the use of or inability to use such software components.The same applies even when
the copyright holders or relevant third parties have been informed of the possibility of such loss. “Loss” here includes normal,
special, incidental and indirect loss (including, but not limited to, the loss of data or its accuracy; loss incurred by the user or any
third party; and interface incompatibility with other software). Please read each EULA for details on the use conditions and items
that must be observed regarding these software components.
The table below lists the software components pre-installed in the TOSHIBA BD player, which are subject to EULAs. The user
should read the applicable EULAs carefully before using these software components. The EULAs are exhibited in their original
text (English) as exactly written by the respective parties other than TOSHIBA.
Open-Source Third-party Software Included in the BD-Player (as of Feb 2010):
Software
License (*= source must be distributed on request)
A copy of the GPL2.0 license is provided in Appendix K
A copy of the LGPL2.1 license is provided in Appendix L
*backtrace
*directfb-extra
*cairo
GPL2 (Included in DVD 3.x [7630 systems] only)
GPL2
LGPL2
LGPL2
LGPL2
*directfb
*iconv
openssl
BSD-old dual license.
The terms and conditions which apply to this software are provided in Appendix H.
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit
(http://www.openssl.org)
curl
The terms and conditions which apply to this software are provided in Appendix A.
*freetype
The terms and conditions which apply to this software are provided in Appendix G.
Recommended advertisement is:
Portions of this software are copyright © <year> The FreeType
Project (www.freetype.org). All rights reserved.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
jpeg
expat
mng
png
xml
The terms and conditions which apply to this software are provided in Appendix B.
The terms and conditions which apply to this software are provided in Appendix I.
The terms and conditions which apply to this software are provided in Appendix C.
The terms and conditions which apply to this software are provided in Appendix D.
The terms and conditions which apply to this software are provided in Appendix E.
The terms and conditions which apply to this software are provided in Appendix F.
BSD-new
zlib
Elecktra
Ltdl
LPGL
Open-Source Third-party Software Included in the Kernel/Rootfs: (as of Feb 2010)
(*= source must be distributed on request)
A copy of the GPL license is provided in Appendix K
A copy of the LGPL license is provided in Appendix L
Utility
Base Version
License
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
zlib license
*kernel
*arp
net-tools-1.52
GNU Bash-3.2
busybox-1.11.1
cramfs
*bash
*busybox
*cramfsck
*dhcpcd
*e2fsprogs
*fdisk
dhcpcd-1.3
e2fsprogs-1.41.5
fdisk-2.10m
TinyLogin-0.80
sysutils
*getty
*hostnamesysutils
*ifconfig
*kill
net-tools-1.52
sysutils
*mkcramfs
*ntfs-3g
cramfs
ntfs-3g 2009.4.4
TinyLogin-0.80
sysutils
*passwd
*ps
*route
net-tools-1.52
sfdisk-3.07
*sfdisk
*shutdown
*tinylogin
*hotplug
*utelnetd
*procps
sysutils
TinyLogin-0.80
hotplug-1.8
utelnetd-0.1.3
procps-3.2.8
freetype-2.1.2
GNU Bash-2.05
GNU termcap 1.3
zlib-1.2.3
*libfreetype.so.6.3.
*libtermcap.so
*libtermcap.so.2.0.8
zlib
The terms and conditions which apply to this software are provided in Appendix F.
libusb.so
uClibc
libusb-0.1.12
LGPL 2.1
LGPL 2.1
BSD-new
uClibc-nptl-0.9.29-20070423
tcpdump-4.0.0
tcpdump
The terms and conditions which apply to this software are provided in Appendix M.
strace strace 4.5.18
The terms and conditions which apply to this software are provided in Appendix M.
hdparm hdparm-6.9
The terms and conditions which apply to this software are provided in Appendix M.
libpcap libcap-1.0.0
The terms and conditions which apply to this software are provided in Appendix M.
portmap portmap
BSD-new
BSD-new
BSD-new
BSD-old
The terms and conditions which apply to this software are provided in Appendix J.
Advertising sentence is:
Copyright (c) 1990 The Regents of the University of California. All rights reserved.
openssl 0.9.8k BSD-old. See advertisement notice above.
openssl
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
pata_platform.ko
GPL
scsi_wait_scan.ko
Badblocks
compile_et
e2fsck
GPL
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.0
GPL2.1
GPL2.1
GPL2.1
Unique license
Unique license
flash_erase
flash_eraseall
flash_info
fsck
geneccerror
hdparm
hotplog
libcom_err
libe2p
libext2fs
libgcc_s
libnandutils
libproc
nanddump
nandwrite
netstat
ntpdate
top
tune2fs
ubiattach
ubicrc32
ubidetach
ubiformat
ubimkvol
ubinfo
ubinize
ubirename
ubirmvol
ubiupdatevol
vmstat
libusb-config
libusbpp
libuuid
Tip
Unzip
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Luxi Font Copyright
Luxi fonts copyright (c) 2001 by Bigelow & Holmes Inc. Luxi font instruction code copyright (c) 2001 by URW++ GmbH. All Rights Reserved. Luxi is
a registered trademark of Bigelow & Holmes Inc. Permission is hereby granted, free of charge, to any person obtaining a copy of these Fonts and
associated documentation files (the “Font Software”), to deal in the Font Software, including without limitation the rights to use, copy, merge,
publish, distribute, sublicense, and/or sell copies of the Font Software, and to permit persons to whom the Font Software is furnished to do so,
subject to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies of one or more of the Font Software.
The Font Software may not be modified, altered, or added to, and in particular the designs of glyphs or characters in the Fonts may not be modified
nor may additional glyphs or characters be added to the Fonts. This License becomes null and void when the Fonts or Font Software have been
modified.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT,
PATENT, TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL BIGELOW & HOLMES INC. OR URW++ GMBH. BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT
SOFTWARE OR FROM OTHER DEALINGS IN THE FONT SOFTWARE.
Except as contained in this notice, the names of Bigelow & Holmes Inc. and URW++ GmbH. shall not be used in advertising or otherwise to promote
the sale, use or other dealings in this Font Software without prior written authorization from Bigelow & Holmes Inc. and URW++ GmbH.
For further information, contact:
Appendix A - CURL license
COPYRIGHT AND PERMISSION NOTICE
Copyright (c) 1996 - 2009, Daniel Stenberg, <[email protected]>.
All rights reserved.
Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright
notice and this permission notice appear in all copies.
THE SOFTWARE IS PROVIDED „AS IS“, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY
RIGHTS. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE
OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other
dealings in this Software without prior written authorization of the copyright holder.
Appendix B - JPEG License
LEGAL ISSUES
============
In plain English:
1. We don’t promise that this software works. (But if you find any bugs, please let us know!)
2. You can use this software for whatever you want. You don’t have to pay us.
3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that
you’ve used the IJG code.
In legalese:
The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy,
merchantability, or fitness for a particular purpose. This software is provided “AS IS”, and you, its user, assume the entire risk as to its quality
and accuracy.
This software is copyright (C) 1991-1998, Thomas G. Lane.
All Rights Reserved except as specified below.
Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for any purpose, without fee, subject to these
conditions:
(1) If any part of the source code for this software is distributed, then this README file must be included, with this copyright and no-warranty notice
unaltered; and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation.
(2) If only executable code is distributed, then the accompanying documentation must state that “this software is based in part on the work of the
Independent JPEG Group”.
(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept
NO LIABILITY for damages of any kind.
These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought
to acknowledge us.
Permission is NOT granted for the use of any IJG author’s name or company name in advertising or publicity relating to this software or products
derived from it. This software may be referred to only as “the Independent JPEG Group’s software”.
We specifically permit and encourage the use of this software as the basis of commercial products, provided that all warranty or liability claims are
assumed by the product vendor.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Appendix C - MNG License
/* **************************************************************************************************************************************************
COPYRIGHT NOTICE:
Copyright (c) 2000 Gerard Juyn ([email protected])
[You may insert additional notices after this sentence if you modify this source]
For the purposes of this copyright and license, “Contributing Authors” is defined as the following set of individuals:
Gerard Juyn
The MNG Library is supplied “AS IS”. The Contributing Authors disclaim all warranties, expressed or implied, including, without limitation, the
warranties of merchantability and of fitness for any purpose. The Contributing Authors assume no liability for direct, indirect, incidental, special,
exemplary, or consequential damages, which may result from the use of the MNG Library, even if advised of the possibility of such damage.
Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the
following restrictions:
1. The origin of this source code must not be misrepresented; you must not claim that you wrote the original software.
2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source.
3. This Copyright notice may not be removed or altered from any source or altered source distribution.
The Contributing Authors specifically permit, without fee, and encourage the use of this source code as a component to supporting the MNG and
JNG file format in commercial products. If you use this source code in a product, acknowledgment would be highly appreciated.
Parts of this software have been adapted from the libpng package. Although this library supports all features from the PNG specification (as MNG
descends from it) it does not require the libpng package. It does require the zlib library and optionally the IJG jpeg library, and/or the “little-cms”
library by Marti Maria (depending on the inclusion of support for JNG and Full-Color-Management respectively.
This library’s function is primarily to read and display MNG animations. It is not meant as a full-featured image-editing component! It does however
offer creation and editing functionality at the chunk level. (future modifications may include some more support for creation and or editing)
*/
Appendix D - PNG License File Distribution Clause
The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this source code as a component to
supporting the PNG file format in commercial products. If you use this source code in a product, acknowledgment is not required but would be
appreciated.
Appendix E – XML License
Except where otherwise noted in the source code (e.g. the files hash.c, list.c and the trio files, which are covered by a similar licence but with
different Copyright notices) all the files are:
Copyright (C) 1998-2003 Daniel Veillard. All Rights Reserved.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”),
to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or
sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
THE DANIEL VEILLARD BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT
OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
Except as contained in this notice, the name of Daniel Veillard shall not be used in advertising or otherwise to promote the sale, use or other
dealings in this Software without prior written authorization from him.
Appendix F – zlib Distribution Conditions
This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held liable for any damages arising from
the use of this software.
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely,
subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a
product, an acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
Jean-loup Gailly
Mark Adler
If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to sign. The sources are provided for free but
without warranty of any kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not include third-party code.
If you redistribute modified sources, we would appreciate that you include in the file ChangeLog history information documenting your changes.
Please read the FAQ for more information on the distribution of modified source versions.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix G – Freetype License
The FreeType Project LICENSE
----------------------------
2006-Jan-27
Copyright 1996-2002, 2006 by
David Turner, Robert Wilhelm, and Werner Lemberg
Introduction
============
The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine, various tools
and contributions which rely on, or relate to, the FreeType Project.
This license applies to all files found in such packages, and which do not fall under their own explicit license. The license affects thus the FreeType
font engine, the test programs, documentation and makefiles, at the very least.
This license was inspired by the BSD, Artistic, and IJG (Independent JPEG Group) licenses, which all encourage inclusion and use of free software
in commercial and freeware products alike. As a consequence, its main points are that:
o
o
o
We don’t promise that this software works. However, we will be interested in any kind of bug reports. (`as is’ distribution)
You can use this software for whatever you want, in parts or full form, without having to pay us. (`royalty-free’ usage)
You may not pretend that you wrote this software. If you use it, or only parts of it, in a program, you must acknowledge somewhere in your
documentation that you have used the FreeType code. (`credits’)
We specifically permit and encourage the inclusion of this software, with or without modifications, in commercial products.We disclaim all warranties
covering The FreeType Project and assume no liability related to The FreeType Project.
Finally, many people asked us for a preferred form for a credit/disclaimer to use in compliance with this license. We thus encourage you to use the
following text:
“””
Portions of this software are copyright © <year> The FreeType Project (www.freetype.org). All rights reserved.
“””
Please replace <year> with the value from the FreeType version you actually use.
Legal Terms
===========
0. Definitions
--------------
Throughout this license, the terms `package’, `FreeType Project’, and `FreeType archive’ refer to the set of files originally distributed by the authors
(David Turner, Robert Wilhelm, and Werner Lemberg) as the `FreeType Project’, be they named as alpha, beta or final release.
`You’ refers to the licensee, or person using the project, where `using’ is a generic term including compiling the project’s source code as well as
linking it to form a `program’ or `executable’. This program is referred to as `a program using the FreeType engine’.
This license applies to all files distributed in the original FreeType Project, including all source code, binaries and documentation, unless otherwise
stated in the file in its original, unmodified form as distributed in the original archive. If you are unsure whether or not a particular file is covered by
this license, you must contact us to verify this.
The FreeType Project is copyright (C) 1996-2000 by David Turner, Robert Wilhelm, and Werner Lemberg. All rights reserved except as specified
below.
1. No Warranty
--------------
THE FREETYPE PROJECT IS PROVIDED `AS IS’ WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL ANY OF
THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY THE USE OR THE INABILITY TO USE, OF THE
FREETYPE PROJECT.
2. Redistribution
-----------------
This license grants a worldwide, royalty-free, perpetual and irrevocable right and license to use, execute, perform, compile, display, copy, create
derivative works of, distribute and sublicense the FreeType Project (in both source and object code forms) and derivative works thereof for any
purpose; and to authorize others to exercise some or all of the rights granted herein, subject to the following conditions:
o
Redistribution of source code must retain this license file (`FTL.TXT’) unaltered; any additions, deletions or changes to the original files must be
clearly indicated in accompanying documentation.The copyright notices of the unaltered, original files must be preserved in all copies of source
files.
o
Redistribution in binary form must provide a disclaimer that states that the software is based in part of the work of the FreeType Team, in
the distribution documentation. We also encourage you to put an URL to the FreeType web page in your documentation, though this isn’t
mandatory.
55
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
These conditions apply to any software derived from or based on the FreeType Project, not just the unmodified files. If you use our work, you must
acknowledge us. However, no fee need be paid to us.
3. Advertising
--------------
Neither the FreeType authors and contributors nor you shall use the name of the other for commercial, advertising, or promotional purposes without
specific prior written permission.
We suggest, but do not require, that you use one or more of the following phrases to refer to this software in your documentation or advertising
materials: `FreeType Project’, `FreeType Engine’, `FreeType library’, or `FreeType Distribution’.
As you have not signed this license, you are not required to accept it. However, as the FreeType Project is copyrighted material, only this license,
or another one contracted with the authors, grants you the right to use, distribute, and modify it. Therefore, by using, distributing, or modifying the
FreeType Project, you indicate that you understand and accept all the terms of this license.
4. Contacts
-----------
There are two mailing lists related to FreeType:
Discusses general use and applications of FreeType, as well as future and wanted additions to the library and distribution.
If you are looking for support, start in this list if you haven’t found anything to help you in the documentation.
Discusses bugs, as well as engine internals, design issues, specific licenses, porting, etc.
Our home page can be found at
--- end of FTL.TXT ---
Appendix H – Openssl License
LICENSE ISSUES
==============
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the
toolkit.
See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to
OpenSSL, please contact [email protected].
OpenSSL License
---------------
/* ====================================================================
Copyright (c) 1998-2008 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgment:“This product includes software
developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without
prior written permission. For written permission, please contact [email protected].
5. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission *
of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by the OpenSSL
Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS’’ AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric Young ([email protected]). This product includes software written by Tim Hudson
*/
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Original SSLeay License
-----------------------
This package is an SSL implementation written by Eric Young ([email protected]). The implementation was written so as to conform with
Netscapes SSL.
This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to
all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this
distribution is covered by the same copyright terms except that the holder is Tim Hudson ([email protected]).
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric
Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or
in documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product includes
The word ‘cryptographic’ can be left out if the rouines from the library being used are not cryptographic related :-).
4. IfyouincludeanyWindowsspecificcode(oraderivativethereof)fromtheappsdirectory(applicationcode)youmustincludeanacknowledgement:
“This product includes software written by Tim Hudson ([email protected])”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be
copied and put under another distribution licence [including the GNU Public Licence.]
*/
Appendix I – Expat License
Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper Copyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat
maintainers.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”),
to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or
sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION
OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
DEALINGS IN THE SOFTWARE.
Appendix J – Portmap License
/*-
Copyright (c) 1990 The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes
software developed by the University of California, Berkeley and its contributors.
4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Appendix K – GNU GPL 2.0
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is
intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free
Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the
freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that
you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These
restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have.You must
make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute
and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the
software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems
introduced by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will
individually obtain patent licenses, in effect making the program proprietary.To prevent this, we have made it clear that any patent must be licensed
for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under
the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means
either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or
with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each
licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the
Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of
having been made by running the Program). Whether that is true depends on what the Program does.
1.You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License
and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2.You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such
modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be
licensed as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the
most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else,
saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of
this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is
not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be
reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when
you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the
distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right
to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of
a storage or distribution medium does not bring the other work under the scope of this License.
3.You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections
1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2
above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing
source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2
above on a medium customarily used for software interchange; or,
58
Download from Www.Somanuals.com. All Manuals Search And Download.
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for
noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection
b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code
means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and
installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed
(in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs,
unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the
source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along
with the object code.
4.You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy,
modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have
received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5.You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the
Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the
Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying,
distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original
licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the
recipients’ exercise of the rights granted herein.You are not responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions
are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from
the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent
obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free
redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and
the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this
section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices.
Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application
of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright
holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that
distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body
of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will
be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later
version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software
Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software
Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask
for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make
exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting
the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK
AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITHYOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME
THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE
THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED
BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER
OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Appendix L – GNU LGPL 2.1
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the
version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are
intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software
Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the
ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you
have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want
it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These
restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You
must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to
the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these
terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to
copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone
else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be
affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively
restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for
a version of the library must be consistent with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General
Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for
certain libraries in order to permit linking those libraries into non-free programs.
When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work,
a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria
of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.
We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public
License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are
the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special
circumstances.
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-
facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job
as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General
Public License.
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software.
For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as
well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with
the Library has the freedom and the wherewithal to run that program using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based
on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the
library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other
authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”). Each licensee is
addressed as “you”.
A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some
of those functions and data) to form executables.
The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library”
means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim
or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term
“modification”.)
“Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the
source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation
of the library.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a
program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library
(independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that
uses the Library does.
1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that
refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such
modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other
than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application
does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore,
Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it,
the square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be
reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when
you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the
distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right
to control the distribution of derivative or collective works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a
storage or distribution medium does not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this,
you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this
License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead
if you wish.) Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent
copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of
Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed
under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.
If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code
from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along
with the object code.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it,
is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of
this License.
However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions
of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution
of such executables.
When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be a derivative
work of the Library even though the source code is not.
Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be
true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines
or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this
object code plus portions of the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables
containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce a work containing
portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the
customer’s own use and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License.
You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library
among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things:
a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were
used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the
complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then
relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions
files in the Library will not necessarily be able to recompile the application to use the modified definitions.)
b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library
already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a
modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work
was made with.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above,
for a charge no more than the cost of performing this distribution.
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified
materials from the same place.
e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.
For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for reproducing the
executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either
source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that
component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating
system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.
7.You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered
by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other
library facilities is otherwise permitted, and provided that you do these two things:
a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must
be distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the
accompanying uncombined form of the same work.
8.You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise
to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However,
parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in
full compliance.
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute
the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing
the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying,
distributing or modifying the Library or works based on it.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original
licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the
recipients’ exercise of the rights granted herein.You are not responsible for enforcing compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions
are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from
the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent
obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free
redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and
the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this
section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices.
Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application
of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright
holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that
distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the
body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new
versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and “any
later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free
Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software
Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the
author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software
and of promoting the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED
BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE
THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE
THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED
BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR
OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
62
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone
can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General
Public License).
To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey
the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.
<one line to give the library’s name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by
the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.
Thislibraryisdistributedinthehopethatitwillbeuseful, butWITHOUTANYWARRANTY;withouteventheimpliedwarrantyofMERCHANTABILITY
or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation,
Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Also add information on how to contact you by electronic and paper mail.You should also get your employer (if you work as a programmer) or your
school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob’ (a library for tweaking knobs) written by James Random Hacker.
<signature of Ty Coon>, 1 April 1990
Ty Coon, President of Vice
That’s all there is to it!
Appendix M – BSD-New
/*
Copyright (c) 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997
The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that: (1) source code distributions retain
the above copyright notice and this paragraph in its entirety, (2) distributions including binary code include the above copyright notice and this
paragraph in its entirety in the documentation or other materials provided with the distribution, and (3) all advertising materials mentioning features
or use of this software display the following acknowledgement:
``This product includes software developed by the University of California, Lawrence Berkeley Laboratory and its contributors.’’ Neither the name
of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED ``AS IS’’ AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
*/
Appendix N – CinemaNow
Third Party Requirements
a. gSOAP.
The following notice is applicable to the CinemaNow SDK. Company is required to include such notice in the documentation for any Embedded
Products it distributes.
Part of the software embedded in this product is gSOAP software.
Portions created by gSOAP are Copyright (C) 2001-2004 Robert A. van Engelen, Genivia Inc. All Rights Reserved.
THE SOFTWARE IN THIS PRODUCT WAS IN PART PROVIDED BY GENIVIA INC AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
b. [THE CODE IS BEING PROVIDED IN OBJECT CODE SO THE ABOVE DOESN’T APPLY]
c. Curl/ 7.12.2
COPYRIGHT AND PERMISSION NOTICE
Copyright (c) 1996 - 2009, Daniel Stenberg, <[email protected]>.
All rights reserved.
Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright
notice and this permission notice appear in all copies.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY
RIGHTS. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE
OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other
dealings in this Software without prior written authorization of the copyright holder.
d. C-ARES 1.6.0
Copyright 1998 by the Massachusetts Institute of Technology.
Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that
the above copyright notice appear in all copies and that both that copyright notice and this permission notice appear in supporting documentation,
and that the name of M.I.T. not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission.
M.I.T. makes no representations about the suitability of this software for any purpose. It is provided “as is” without express or implied warranty.
e. Openssl 0.9.5a
Original SSLeay License
-----------------------
This package is an SSL implementation written by Eric Young ([email protected]). The implementation was written so as to conform with
Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are adhered to. The following
conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation
included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson ([email protected]).
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric
Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or
in documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product includes
cryptographic software written by Eric Young ([email protected])” The word ‘cryptographic’ can be left out if the rouines from the library being
used are not cryptographic related :-).
4.If you include anyWindows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement:
“This product includes software written by Tim Hudson ([email protected])”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The license and distribution terms for any publicly available version or derivative of this code cannot be changed. i.e. this code cannot simply be
copied and put under another distribution license [including the GNU Public License.]
Content owners use Windows Media digital rights management technology (WMDRM) to protect their intellectual property, including copyrights.
This device uses WMDRM software to access WMDRM-protected content. If the WMDRM software fails to protect the content, content owners
may ask Microsoft to revoke the software¡¯s ability to use WMDRM to play or copy protected content. Revocation does not affect unprotected
content. When you download licenses for protected content, you agree that Microsoft may include a revocation list with the licenses. Content
owners may require you to upgrade WMDRM to access their content. If you decline an upgrade, you will not be able to access content that requires
the upgrade.
Printed in China
811-BD3091W011
Download from Www.Somanuals.com. All Manuals Search And Download.
|