Toshiba Blu ray Player BDX2500KU User Manual

Blu-ray Disc Player

BDX2500KU

OWNER'S MANUAL

Owner's Record

The model number and serial number are on the back

of this unit. Record these numbers in the spaces

below. Refer to these numbers whenever you communicate

with your Toshiba dealer about this unit.

Model number:

Serial number :

E8EB6CD_SD-V398KC_EN_v1.indd

2009/01/29 17:04:54

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

SAFETY PRECAUTIONS

The lightning ﬂash with an arrowhead symbol, within the equilateral

triangle, is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of

sufﬁcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within the equilateral triangle is intended to

alerttheusertothepresenceofimportantoperatingandmaintenance

(servicing) instructions in this owner’s manual.

CAUTION: VISIBLE LASER RADIATION WHEN

OPEN. DO NOT STARE INTO BEAM.

AVIS

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS

HIGHVOLTAGES ARE PRESENT INSIDETHE ENCLOSURE.DO NOT OPEN

THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

WARNING:TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

The symbol for Class II (Double lnsulation)

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that

produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided

for your safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury

from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such

as the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally, or has been dropped.

ADDITIONAl SAFETY INSTRUCTIONS

15. Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a risk of ﬁre or electric

shock.

16. Apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with liquids, such as vases, shall be placed on

the apparatus.

17. Keep your ﬁngers well clear of the disc tray as it is closing. Neglecting to do so may cause serious personal injury.

18. Do not place a heavy object on or step on the apparatus. The object may fall, causing serious personal injury and serious

damage to the apparatus.

19. Do not use a cracked , deformed, or repaired disc.These discs are easily broken and may cause serious personal injury and

apparatus malfunction.

20. If the apparatus should emit smoke or an unusual odor, immediately disconnect the power cord from the wall outlet.Wait until

the smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause ﬁre.

21. During thunderstorms, do not touch the connecting cables or the apparatus.

22. Warning: To prevent spread of ﬁre, keep candles or other open ﬂames away from this product at all times.

23. The mains plug is used as disconnect device. The mains plug of apparatus should not be obstructed OR should be easily

accessed during intended use.To be completely disconnect the power input, the mains plug of apparatus shall be disconnected

from the mains.

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

CAUTION:

•

To prevent direct exposure to laser beam, do not try to open the enclosure. Visible and invisible laser radiation when open and

interlocks defeated. DO NOT STARE INTO BEAM.

•

Use of controls or adjustments or performance of procedures other than those speciﬁed may result in hazardous radiation

exposure.

• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Warning: Batteries shall not be exposed to excessive heat such as sunshine, ﬁre or the like.

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

The party responsible for compliance to these rules is:

Toshiba America Consumer Products, L.L.C.

82 Totowa Rd. Wayne, NJ 07470.

Ph: 1-800-631-3811

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

WARNING: Changes or modiﬁcations to this unit not expressly approved by Toshiba, or parties authorized by Toshiba, could void

the user’s authority to operate the equipment.

Notes On Copyright

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.

Use of this copyright protection technology must be authorized by Rovi Corporation, and is intended for home and other limited

viewing uses only unless otherwise authorized by Rovi Corporation. Reverse engineering or disassembly is prohibited.

On Placement

•

Do not use this unit in places which are extremely hot, cold, dusty or humid.

Do not restrict the air ﬂow of this unit by placing it somewhere with poor air ﬂow, by covering it with a cloth, or by placing it on

bedding or carpeting.

•

Be sure to remove the disc and unplug the AC power cord from the outlet before carrying the unit.

On Safety

• Do not handle the AC power cord with wet hands and do not put your ﬁngers or objects into the unit.

• When connecting or disconnecting the AC power cord, grip the plug and not the cord itself. Pulling the cord may damage it

and create a hazard.

• When you are not going to use the unit for a long period of time, disconnect the AC power cord.

On Condensation

• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the equipment.

When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1-2 hours before turning

the power on or gradually heat the room and allow the unit to dry before use.

On Recycling

• This unit’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

• Batteries should never be thrown away or incinerated but disposed of in accordance with your local

regulations concerning chemical wastes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

“DVD” is a trademark

of DVD Format / Logo

Licensing Corporation.

Supplied Accessories

HDMI, the HDMI logo, and

High-Deﬁnition Multimedia

Interface are trademarks

or registered trademarks

of HDMI Licensing LLC in

the United States and other

countries.

BONUSVIEW

Manufactured under license

from Dolby Laboratories.

Dolby and the double-D

symbol are trademarks of

Dolby Laboratories.

Remote Control with

Batteries (AAA x 2)

Composite Audio / Video

Cables

OWNER’S MANUAl

Manufactured under license

under U.S. Patent #’s:

5,451,942; 5,956,674;

5,974,380; 5,978,762;

6,226,616; 6,487,535;

7,392,195; 7,272,567;

7,333,929; 7,212,872 &

other U.S. and worldwide

patents issued & pending.

DTS and the Symbol are

registered trademarks, &

DTS-HD, DTS-HD Master

Audio | Essential and the

DTS logos are trademarks

of DTS, Inc. Product

Owner’s Manual

(EN)

Quick Start Guide

(EN/ES)

Symbols used in this Manual

To specify for which media type each function is, we put the

following symbols at the beginning of each item to operate.

Symbol

Description

includes software. © DTS,

Description refers to BD-video and BD-RE

/ BD-R recorded in BDMV format

“x.v.Color” and “x.v.Color”

logo are trademarks of Sony

Corporation.

Description refers to DVD-video

Description refers to Audio CD / DTS-CD

“AVCHD” and the “AVCHD”

logo are trademarks of

Panasonic Corporation and

Sony Corporation.

Description refers to DVD-RW/-R with

AVCHD ﬁles

Description refers to BD-RE/-R, DVD-

RW/-R, CD-RW/-R and SD Memory Card

with MP3 ﬁles

“BONUSVIEW” is trademark

of Blu-ray Disc Association.

Description refers to BD-RE/-R, DVD-

RW/-R, CD-RW/-R and SD Memory Card

with Windows Media™ Audio ﬁles

Java and all other Java

trademarks and logos are

trademarks or registered

trademarks of Sun

Microsystems, Inc. in the

United States and/or other

countries.

Description refers to BD-RE/-R, DVD-

RW/-R, CD-RW/-R and SD Memory Card

with JPEG ﬁles

If you do not ﬁnd any of the symbols listed above under the

function heading, the operation is applicable to all media.

“BD-LIVE” logo is trademark

of Blu-ray Disc Association.

Trademark Information

Windows Media and the

Windows logo are

“Blu-ray Disc” and

Association.

are trademarks of Blu-ray Disc

trademarks or registered

trademarks of Microsoft

Corporation in the United

States and/or other

countries.

Blockbuster is a registered trademark of Blockbuster, Inc.

Netﬂix is a registered trademark of Netﬂix Inc.

Pandora is a registered trademark of Pandora Media, Inc.

VUDU is a trademark of VUDU, Inc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Introduction

Accessing a Speciﬁc location Directly.......... 22

Locating a speciﬁc title/chapter/time .......................... 22

SAFETY PRECAUTIONS .....................................2

IMPORTANT SAFETY INSTRUCTIONS ............. 2

PRECAUTIONS ................................................... 3

Supplied Accessories ....................................... 4

Symbols used in the Manual ............................ 4

Trademark Information ...................................... 4

Table of Contents ............................................... 5

Features .............................................................. 6

Repeating a Title, Chapter, Track or Specific

Segment ............................................................ 23

Repeating a title, chapter or track ............................... 23

Repeating a speciﬁc segment .................................... 23

Playing in a Random Order.............................. 23

Playing tracks or ﬁles in a random order .................... 23

PIP(BONUSVIEW) Setting................................ 24

Camera Angle ................................................... 24

Audio Selection................................................. 24

Subtitle Selection ............................................. 25

Displaying On-screen Information.................. 25

Identiﬁcation of Controls .................................. 7

Front panel.....................................................................7

Rear panel......................................................................7

Using the Remote Control ................................ 8

Remote Control..............................................................8

Installing batteries..........................................................9

Operating with the remote control................................10

Front Panel Display ......................................................10

Playing AVCHD/MP3/WMA/JPEG Files ............26

Playing ﬁles on a data disc.......................................... 26

Using an SD Card ..............................................27

Inserting an SD card .................................................. 27

Using a USB Device ..........................................28

Operating a USB device ............................................. 28

Connections

Connecting to a TV .......................................... 11

Connecting to a TV using an HDMI cable ....................12

Connecting to a TV using a component video..............12

Connecting to a TV using an A/V cable........................12

Customizing the Function Settings

General Operations ...........................................29

Network Connection Setting ............................29

Info Menu............................................................29

Performing Quick-Setup ...................................29

Display Setting...................................................30

Audio Setting .....................................................31

Speaker Setting .................................................32

language Setting ..............................................33

Parental Control.................................................33

System Setting...................................................34

UpgradingYour Player’s Firmware ..................35

Connecting to an Audio System .....................13

Via 2-Channel Analog Audio Output ........................... 13

Via Digital Audio Output .............................................. 13

Via HDMI Audio Output ............................................... 13

Wired Network Connection ..............................14

Connecting your player to a wired router .................... 14

Wireless Network Connection .........................15

Connecting the Speakers .................................16

Positioning the Speakers..................................17

Playback

Using the Connected Applications .................36

Watching movies with Netﬂix^™.................................... 36

Watching movies with Blockbuster^®............................ 37

Watching movies with VUDU^™.................................... 37

Listening to music with Pandora^™............................... 38

Information on Playback.................................. 18

Playable Discs and Files ............................................. 18

Unplayable Discs and Files......................................... 18

Color Systems............................................................. 19

Region Codes ............................................................. 19

Structure of Disc/SD Card Contents ........................... 19

Using BD-live^TMFeatures ................................38

Playing a Disc ................................................... 20

Basic playback ............................................................ 20

Others

Troubleshooting & Maintenance ......................39

Troubleshooting........................................................... 39

Maintenance ............................................................... 40

Variable Speed Playback.................................. 21

Playing in fast reverse / forward directions.................. 21

Playing frame by frame ............................................... 21

Playing in slow motion ................................................ 21

Glossary .............................................................41

Speciﬁcations ....................................................43

limited Warranty................................................44

locating a Desired Section ............................. 21

Locating a title using the top menu ............................. 21

Locating a speciﬁc chapter or track............................. 22

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Features

Blu-ray Disc

x.v.Color

You can enjoy Blu-ray Disc which is capable of storing ﬁve times

more data than a conventional DVD.

This unit supports playback of video contents on discs recorded

with “x.v.Color” technology. To watch this video content with

the “x.v.Color”, a TV or other display device supporting both

video image reproduction using the “x.v.Color” standard and

capable of manually switching it’s color setting is required.

Please refer to the owner’s manual of your display device for

further information.

BD-Java

With some BDs which support Java applications, you can enjoy

the interactive functions such as games or interactive menus.

BD-live

BD-Live (BD-ROM version 2 Proﬁle 2.0) that allows interactive

functions to be used when this unit is connected to the Internet

in addition to the BONUSVIEW function.The various functions

differ depending on the disc.

Easy and simple connection to your HDTV via HDMI

Connect this unit to your HDTV with one single HDMI (High-

Deﬁnition Multimedia Interface) cable. It is recommended to

use a High Speed HDMI Cable for better compatibility.The high

deﬁnition video output signal will be transferred to your HDTV

without conversion to analog signals, so you will get excellent

picture and sound quality.

Full high-deﬁnition video playback

Watch movies in the highest picture quality available for your

HDTV. This unit offers full high-deﬁnition video playback up to

1080p resolution for an amazing viewing experience. A highly

detailed picture and increased sharpness delivers a more true-

to-life picture.

Thanks to other multiple outputs, you can also easily connect

to your home theater system or ampliﬁer.

DVD Upconversion for enhanced picture quality

HDMI CEC (Consumer Electronics Control)

This unit supports HDMI CEC, which allows integrated system

control over HDMI and is part of the HDMI standard.

Your current DVD will look even better than before thanks to

video upconversion. Upconversion will increase the resolution

of standard deﬁnition DVD to high deﬁnition up to 1080p over

an HDMI connection. The picture will be less jagged and more

realistic for a near high-deﬁnition experience.

This function may not work properly on some devices.

HDMI 1080p/24F output (BD only)

Enjoy your content on different kinds of media

This unit is equipped with a feature which can provide the

smooth movement in the playback of ﬁlm originated material

with the frame rate of 24 frames per second with progressive

scan. (Available only when the TV is connected by an HDMI

cable and compatible with 1080p/24F frame input.)

Full backwards compatibility with BD, DVD, CD and SD card

ensures that you can continue to enjoy your current audio-video

collection. Additionally, you can view JPEG digital pictures or

listen to MP3 or Windows Media™ Audio music ﬁles.

Refer to “Display Setting” in “Customizing the Function

Settings” on page 30.

Experience rich multi-channel surround sound

Multi-channel surround sound, which recognizes real-to-life

sound and makes you feel like you are really there.

To play back the digital video images of a BD / DVD via an HDMI

connection, it is necessary that both the unit and the TV (or an

AV ampliﬁer) support a copyright protection system called HDCP

(high-bandwidth digital content protection system). HDCP is

copy protection technology that comprises data encryption and

authentication of the connected AV device. This unit supports

HDCP. Please read the operating instructions of your TV (or AV

ampliﬁer) for more information.

PIP (BONUSVIEW)

Some BD-videos have the PIP function which enables you to

display the secondary video in the primary video.You can call

up the secondary video by pressing BONUSVIEW whenever

the scene contains the secondary video.

Pop-up menu

Some BD-video have pop-up menu which is a navigation menu

that can be called up and be operated on theTV screen without

interrupting the playback.You can call up the pop-up menu by

pressing POPUP/TOP MENU or MENU.Contents in the pop-up

menu vary depending on the disc.

Playback of Content from an SD Memory Card

You can play back MP3 /WMA / JPEGs stored in an SD Memory

Card.You can store picture-in-picture commentary, subtitles or

other extras for BD-ROM ver. 2 (Proﬁle 2.0 / Proﬁle 1.1) ﬁles in

an SD Memory Card and play back with the BD-video.

Playing back AVCHD ﬁles

This unit supports playback of AVCHD format ﬁles (new format

for high deﬁnition video camcorders) recorded on disc.Your high

deﬁnition personal archive is playable in HD quality.

Download from Www.Somanuals.com. All Manuals Search And Download.

Identiﬁcation of Controls

Front panel

1. Disc tray

7. ON/STANDBY indicator

8. SD card slot

2. OPEN/ClOSE button

3. Display

9. ON/STANDBY button

• Refer to “Front Panel Display” on page 10.

• Press to turn on the unit, or to turn the unit into the

standby mode. (To completely turn off the unit, you must

unplug the AC power cord.)

4. Remote sensor

5. STOP button

6. PlAY

button

Rear panel

COMPONENT VIDEO OUT

SBL

SBR

AC IN

BITSTREAM

PCM

VIDEO

OUTPUT

HDMI OUT

OPTICAL

AUDIO OUT

MULTI CHANNEL AUDIO OUTPUT

LAN

USB

1. AC power cord

5. COMPONENT VIDEO OUT jacks

• Connect to a standard AC outlet to supply power to this

• Use to connect a TV with component video inputs using

a component video cable.

unit.

• Unplug this cord from the AC outlet to completely turn

off the unit.

6. MUlTI CHANNEl AUDIO OUTPUT jacks

• Use to connect an AV receiver / ampliﬁer with a audio

cable.

2. lAN terminal

• Use to connect a network equipment with LAN cable.

7. USB jack

• Use to connect USB ﬂash drives (not included).

3. HDMI OUT jack

• Use to connect a TV with an HDMI compatible port via

an HDMI cable.

8. AUDIO OUT jacks

• Use to connect a TV, an AV receiver / ampliﬁer or other

device with a composite audio cable.

4. OPTICAl jack

• Use to connect an AV receiver / ampliﬁer, Dolby Digital /

DTS decoder or other device with a digital audio optical

input jack using a digital audio optical cable.

9. VIDEO OUT jack

• Use to connect a TV, an AV receiver or other device with

a composite video cable.

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Using the Remote control

Remote control

No. Item

Description

Press to adjust aspect ratio in full

stop mode.

ASPECT

OPEN/ClOSE

Press to open or close the disc tray.

Press to display the settings in

home menu.

SETTING

Press to display the Connected in

home menu.

HOME MENU

BONUSVIEW

Press to switch picture-in-picture

feature on or off (only applicable

to BD-video which supports the

PIP function). For more details,

see “PIP (BONUSVIEW) Setting”

on page 24.

BONUSVIEW

Same as SKIP

For detailed operations, please

refer to SKIP / SKIP

/ SKIP

Press to select a viewing angle if

multiple angles are available on

the disc.

ANGlE

VOlUME + / -

AUDIO

Press to adjust the volume.

Press to select the audio mode.

Press to display the subtitle menu.

SUBTITlE

Press to return to the previous

menu.

RETURN

Press to adjust the brightness of

display on the front of the Blu-ray

disc player.

DIMMER

• Press to select items on some

BD contents.

• When ﬁle list / thumbnail list is

shown, press to switch between

pages.

RED / GREEN /

BlUE /YEllOW

During playback, press to fast

reverse the playback.

REV

•

During playback, press once to

return to the beginning of the

current title, chapter, track or ﬁle.

• During playback, press twice

to return to the previous title,

chapter, track or ﬁle.

10 SKIP

•

During the JPEG playback, press

to return to the previous ﬁle.

• Press to pause playback.

•

Whenplaybackisinpausemode,

press repeatedly to forward the

playback step by step.

PAUSE

Press to advance one frame.

Download from Www.Somanuals.com. All Manuals Search And Download.

• In playback mode, press GOTO,

then press the number buttons

to enter a title, chapter, track,

time or ﬁle number.

• In menu mode, press to enter

the parental code password.

Installing batteries

13 Number buttons

Install the batteries (AAAx2) matching the polarity indicated

inside battery compartment of the remote control.

Press to display the search

menu.

Open the cover.

14 GOTO

Press to turn on the unit, or to turn

the unit into the standby mode. (To

completely turn off the unit, you

must unplug the power cord.)

15 ON/STANDBY

• During Blu-ray Disc playback,

press to open

menu that

lets you control Blu-ray Disc

playback.

16 POPUP/TOP MENU

• During DVD playback, press

to open the DVD menu (if

available).

Insert batteries.

In playback mode, press to adjust

picture quality according to your

preference (Actual effect to picture

may vary depending on TV.):

• E.P.M (Ehanced Picture Mode):

The picture is sharper with

enhanced color.

17 PIC

• Sharpness

18 INFO

Press to display disc information.

Presstoselectthevideoresolution

in full stop mode.

19 RESOlUTION

Make sure to match the + and – on the batteries to the

marks indicated in the battery compartment.

Press to return to the previous

menu.

20 MENU

In PIP mode, press to turn the

audio for the secondary video on

or off. For more details, see “PIP

(BONUSVIEW) Setting” on page

24.

Close the cover.

21 2nd AUDIO

Press to select items or settings.

Press to conﬁrm or select menu

items.

In PIP mode, press to turn the

subtitle for the secondary video

on or off.

23 2nd SUBTITlE

During playback, press to fast

forward the playback.

24 FWD

Caution: Never throw batteries into a ﬁre.

Press to start playback or resume

playback.

PlAY

Notes:

•

During playback, press to skip to

the next title, chapter, track or ﬁle.

• Do not mix different battery types or combine used batteries

with new ones.

• If the remote control does not operate correctly, or if the

operating range becomes reduced, replace both batteries

with new ones.

26 SKIP

• During the JPEG playback,

press to go to the next ﬁle.

27 STOP

Press to stop playback.

Press to play back the disc in slow

motion.

• If the batteries are dead or if you will not be using the remote

control for a long time, remove the batteries to prevent battery

acid from leaking into the battery compartment.

Press to toggle between various

repeat modes.

29 REPEAT

Press to turn random function on

or off.

30 RANDOM

Press to play back a deﬁned

section between point A and B

repeatedly.

31 A-B

32 ClEAR

Press to clear an input error.

Press to conﬁrm or select menu

items.

33 ENTER

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Operating with the remote control

* Do not expose the remote sensor of the Blu-ray disc player

to a strong light source such as direct sunlight or other

illumination. If you do so, you may not be able to operate

the Blu-ray disc player via the remote control.

Point the remote control at the remote

sensor and press the buttons.

Notes:

• Direct the remote control at the remote sensor of the Blu-ray

disc player.

• When using the remote control, press the buttons at intervals

of about 1 second to ensure the correct mode of operation.

• Do not drop or give the remote control a shock.

• Do not leave the remote control near an extremely hot or humid

place.

• Do not spill water or put anything wet on the remote control.

• Do not open the remote control.

Distance: About5mfromthefront

of the remote sensor.

Angle:

About 30° in each

direction of the front of

the remote sensor.

• If the remote control is not going to be used for a long time,

remove the battery to avoid damage caused by battery leakage

corrosion.

Front Panel Display

DVD

TRK 2 c h

HDMI

MUlTI

1080ip

720p

576ip

480ip

10.

SKIP indicator

1. PlAY indicator

Lights when playing.

2. PAUSE indicator

Lights when paused.

3. DVD indicator

Lights while in fast forward / fast reverse mode.

11. Resolution indicator

Shows resolution of video output.

12. Character indicators

Displays various kinds of information such as elapsed time

or message, etc. (See Example shown as below.)

Lights when a DVD disc is inserted.

4. CD indicator

Lights when a CD disc is inserted.

5. TRK (TRACK) indicator

Indicates the

elapsed time

Lights when a CD/MP3 disc is inserted.

6. Audio Channel indicator

Shows the audio channel of the current DVD/BD.

Closing the

disc tray

7. Camera Angle indicator

Illuminates when a BD/DVD disc that has multiple camera

angle is inserted.

Indicates that a

Blu-ray disc is

inserted

8. HDMI indicator

Lights when HDMI TV is connected.

(REPEAT) indicator

Illuminates when REPEAT is pressed.

Loading a disc

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting to a TV

Connect the Blu-ray player to your TV.

1. Choose the appropriate connection, then proceed to the corresponding instruction (A, B or C) on the

next page.

Best

(Supports up to 1080i/1080p, 1080p/24F resolution.)

Your TV

HDMI IN

Go To

High

Definition

HDMI cable

Video

Audio

No analog audio connection required.

HDMI Cable NOT INClUDED

Better

(Supports up to 1080i resolution.)

COMPONENT

VIDEO IN

PB/CB

PR/CR

Your TV

component video cable

composite audio cable

Video

Go To

High

Definition

Audio

AUDIO IN

Component Video Cable NOT INClUDED

Basic

(Supports only 480i resolution.)

VIDEO IN

Your TV

Video

Go To

Standard

Definition

composite audio video cable

Audio

AUDIO IN

• Connect this unit directly to the TV. If the composite audio / video cables are connected to a VCR, pictures may be

distorted due to the copy right protection system.

Composite Video / Audio Cables INClUDED

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

2. Connect the cables by following the illustrations below.

Connecting a TV using an HDMI cable (Best)

Your TV

COMPONENT VIDEO OUT

SBl

AC IN

SBR

BITSTREAM

PCM

VIDEO

OUT

HDMI OUT

OPTICAl

AUDIO OUT

MUlTI CHANNEl AUDIO OUTPUT

lAN

USB

HDMI cable

HDMI IN

HDMI OUT

Notes:

• Do not tilt the connector when inserting it into the HDMI jack, and make sure the shapes of the jack and the connector

are matched.

• When using non-HDCP compatible TV, the image will not display properly.

• An HDMI cable carries both video and audio signals. If you want to use TV speakers, you do not need to make an

additional audio connection if you are using an HDMI cable.

Connecting a TV using a component video cable (Better)

Your TV

COMPONENT VIDEO OUT

SBl

P^B

P^R

AC IN

SBR

BITSTREAM

PCM

VIDEO

OUT

HDMI OUT

OPTICAl

AUDIO OUT

MUlTI CHANNEl AUDIO OUTPUT

lAN

USB

COMPONENT

VIDEO IN

component

video cable

PR/CR

PB/CB

AUDIO IN

COMPONENT VIDEO OUT

VIDEO

OUT

AUDIO OUT

composite audio cable

Connecting a TV using an A/V cable (Good)

COMPONENT VIDEO OUT

SBl

P^B

AC IN

SBR

BITSTREAM

PCM

VIDEO

OUT

HDMI OUT

OPTICAl

AUDIO OUT

MUlTI CHANNEl AUDIO OUTPUT

lAN

USB

VIDEO IN

Your TV

VIDEO

OUT

AUDIO OUT

AUDIO IN

composite audio video cable

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting to an Audio System

•

When you change the connections, all devices should be turned off.

Refer to the manual accompanying external devices for more information.

Via 2-Channel Analog Audio Output

Stereo system

COMPONENT VIDEO OUT

SBl

P^B

AC IN

SBR

BITSTREAM

PCM

VIDEO

OUT

HDMI OUT

AUDIO OUT

MUlTI CHANNEl AUDIO OUTPUT

lAN

USB

OPTICAl

AUDIO IN

AUDIO OUT

composite audio cable

Via Digital Audio Output

AV receiver / amplifier

COMPONENT VIDEO OUT

SBl

P^B

AC IN

SBR

BITSTREAM

PCM

VIDEO

OUT

HDMI OUT

AUDIO OUT

MUlTI CHANNEl AUDIO OUTPUT

lAN

USB

OPTICAl

DIGITAl AUDIO INPUT

OPTICAL

BITSTREAM/PCM

OPTICAl

digital audio optical cable

Via HDMI Audio Output

AV receiver / amplifier

with an HDMI input jack

COMPONENT VIDEO OUT

SBl

P^B

AC IN

SBR

BITSTREAM

PCM

VIDEO

OUT

HDMI OUT

AUDIO OUT

MUlTI CHANNEl AUDIO OUTPUT

lAN

USB

OPTICAl

HDMI IN

HDMI cable

HDMI OUT

Digital Audio Optical Cable and HDMI Cable NOT INClUDED.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Wired Network Connection

Your Blu-ray disc player can be connected to your home network:

•

By connecting an Ethernet cable to the ETHERNET jack on the rear of your player and to a wired hub or router. Using

a wired network provides the best performance, because the attached devices connect directly to the network and

are not subject to radio frequency interference.

Connecting your player to a wired router:

• Connect an Ethernet cable (CAT5 or better with RJ45 connector) to the ETHERNET jack on the back of your player

and to an Ethernet jack on a hub or broadband router.

Hub or broadband router

Networking equipment

(modem, etc.)

WAN

lAN

LAN cable

Internet

lAN

COMPONENT VIDEO OUT

SBl

P^B

AC IN

SBR

BITSTREAM

PCM

VIDEO

OUT

HDMI OUT

AUDIO OUT

MUlTI CHANNEl AUDIO OUTPUT

lAN

USB

OPTICAl

Notes:

• Do not connect a modular phone cable to the ETHERNET jack.

• When plugging or unplugging the cable, hold the connector on the end of the cable. When unplugging, do not pull

on the cable. Press down the lock tab and pull the connector out of the jack.

• Because there are various connection conﬁgurations, follow the instructions from your telecommunication carrier

or Internet service provider.

Download from Www.Somanuals.com. All Manuals Search And Download.

Wireless Network Connection (Need the opTIoNAl Wi-Fi unit of sold separately)

Your Blu-ray disc player can also be connected to network with a Wireless access point.

1. A wireless AP/IP router is required to make a wireless network connection. Connect the wireless LAN adapter to the

USB port on the rear panel of the Blu-ray Disc Player, and set the wireless network options (See Step 2 ~ 3).

2. After the Wi-Fi device inserts to USB terminal, press

to select “Network” from Settings, and press OK to enter.

3. Press to select “Wireless”, and press OK to enter.

(For detailed information, please refer to the user guide for WLM-10UB1.)

COMPONENT VIDEO OUT

SBl

P^B

AC IN

SBR

Wired

BITSTREAM

PCM

VIDEO

OUT

HDMI OUT

AUDIO OUT

MUlTI CHANNEl AUDIO OUTPUT

lAN

USB

OPTICAl

Wireless

Network Test

USB

Wireless access point

Modem Port

Wireless LAN

Adapter

Modem Cable

Notes:

• This unit is compatible with TOSHIBA’s Wireless LAN Adapter only.

Model name: WLM-10UB1

• You must use a wireless IP sharer that supports IEEE 802.11 a/b/g/n. (n is recommended for stable operation of

the wireless network.)

• Wireless LAN, in its nature, may cause interference, depending on the use condition (AP performance, distance,

obstacle, interference by other radio devices, etc.).

• Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not supported.

• When applying the security key for the AP (wireless IP sharer), only the following is supported.

1) Authentication Mode : WEP, WPAPSK, WPA2PSK

2) Encryption Type : WEP, TKIP, AES

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Connecting the Speakers (For 7.1 Audio Channel)

You can connect the speakers as shown in the following diagram to obtain the 7.1 audio channels effects. Using the audio

cables, connect the MUlTI CHANNEl AUDIO OUTPUT (SBL, SBR, C, SW, SL, SR, FL & FR) terminals on the rear of

the Blu-ray disc player to 7.1 Channel ANALOG AUDIO IN terminals of your Ampliﬁer.

For speaker conﬁguration, please refer to “Speaker Setting” on page 32.

COMPONENT VIDEO OUT

SBl

P^B

AC IN

SBR

BITSTREAM

PCM

VIDEO

OUT

HDMI OUT

AUDIO OUT

MUlTI CHANNEl AUDIO OUTPUT

lAN

USB

OPTICAl

SBl

SBR

MUlTI CHANNEl AUDIO OUTPUT

7.1 Channel Amplifier

Notes:

• Please turn the volume down when you turn on the Ampliﬁer.Sudden loud sound may cause damage to the speakers

and your ears.

• The position of terminals may vary depending on the Ampliﬁer. Please refer to the user’s manual of your Ampliﬁer.

• The front left and right outputs on your player and 7.1 channel ampliﬁer must be connected to hear disc menu audio

from certain Blu-ray discs.

• When connecting to a 5.1 channel home theater or receiver, connect all the MUlTI CHANNEl AUDIO OUTPUT jacks

from the player except for the SBL (Surround Back Left) / SBR (Surround Back Right) outputs.

Download from Www.Somanuals.com. All Manuals Search And Download.

positioning the Speakers (For 7.1 Audio Channel)

How you set up your speakers can affect the bass and the sound ﬁeld. Note the following points:

• Place speakers on ﬂat secure bases.

• Placing speakers too close to ﬂoors, walls, and corners can result in excessive bass. Cover walls and windows with

thick curtains.

•

Keep your speakers at least 10 mm away from the system for proper ventilation.

Setup example (For 7.1 audio channels)

Subwoofer

Front speakers

Center speaker

Place the left and right front

speakers equidistant from the

center speaker, about 30º

angle from the center channel.

Place the center speaker directly in front of the

listening area, either above or below the TV.

Vibration caused by the speaker can disrupt the

picture if it is placed on directly on the TV.

Place to the right or left of the

TV, on the floor or a sturdy

shelf so that it will not cause

vibration. Leave about 30 cm

from the TV.

Main unit

To allow for proper ventilation and to maintain

good airflow around the main unit, position it with

at least 5 cm of space on all sides.

AV receiver

Place the AV receiver directly in front of the

listening area, either above or below the TV.

Left & Right Surround speakers

(may be elevated above

the listener)

Surround Back speakers

(may be elevated above

the listener)

Place the left and right surround speakers to the

left and right side of the listening position, in line

with or slightly behind the listening position -

Place the surround back speakers behind the

listening position - slightly to the left and right -

at about 140 -150 from the center speaker.

about 90 -110 from the center.

Note:

The above setup illustration is a basic overview on what to expect when hooking speakers up to your home theater system. The

placement may vary depending on how many and what type of loudspeakers you have, as well as your room size, shaper, and

acoustical properties.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback

Readable cards

SD Memory Card (8 MB - 2 GB)

SDHC Memory Card (4 GB - 8 GB)

miniSD Card (8 MB - 2 GB)

Playable ﬁles/data

Information on playback

MP3, Windows Media^TM

Audio, JPEG, picture-

Before you start playing back a disc, read the following

information.

in-picture

commentary,

subtitles or other extras

for BD-ROM

microSD Card (8 MB - 2 GB)

Playable Discs and Files

• This unit supports SD Memory Card with FAT12/FAT16

ﬁle system, and SDHC Memory Card with FAT32 ﬁle

system.

This unit is compatible to play back the following discs /

ﬁles.

• This unit does not support NTFS ﬁle system.

• This unit may not read the SD Memory Cards formatted

on a computer. If that is the case, please reformat the SD

Memory Cards in this unit and try again.

• This unit does not support miniSDHC and microSDHC

Memory Card.

To play back a disc / ﬁle, make sure that it meets the

requirements for region codes and color systems as

described below. You can play back discs that have the

following logos.

Other disc types are not guaranteed to play back.

• For miniSD Card and microSD Card, the adapter is

necessary.

Playable discs

logos

Blu-ray Disc

miniSD Card

microSD Card

adapter

- BD-ROM (single / dual layer)

- BD-RE (single / dual layer)

(Recorded in BDMV format)

- BD-R (single / dual layer)(Recorded

in BDMV format) (Unclosed discs

may not be played back.)

adapter

miniSD Card

microSD

Card

• Portions of this product are protected under copyright

law and are provided under license by ARIS / SOLANA /

4C.

DVD-ROM

DVD-RW

DVD-R

• Please keep the SD Memory Cards in their cases when

you are not using them.

• Do not try to open or modify the card.

• Do not touch the terminal surface with your ﬁngers or

any metals.

• Do not attach additional labels or stickers to cards.

• Do not remove the label of the SD Memory Cards.

• This unit recognizes up to 8 characters of ﬁle name in

the SD Memory Card. Characters after 8th will not be

displayed.

CD-DA (audio CD)

CD-RW

Unplayable Discs and Files

CD-R

The following discs will not be played back in this unit.

• CD-ROM

DTS-CD

• CD-I (compact disc-interactive)

• DVD-RAM

• VSD (video single disc)

• DVD-audio

Playable ﬁles

Media

• HD DVD

• VIDEO CD

• Unﬁnalized disc

• SACD

AVCHD

DVD-RW/-R

MP3

BD-RE/-R,

RW/-R,

DVD-RW/-R,

Memory

CD-

Card

Windows Media^TMAudio

• BD / DVD / SD Memory Card contains DivX^®ﬁles.

• BD / DVD hybrid disc (played back as a BD-video only)

• BD that contains AVCHD ﬁles

(including SDHC), miniSD Card,

microSD Card

JPEG

•

DVD-RW/-R recorded in non compatible recording

format.

• This unit cannot playback the disc contents protected by • Super Audio CD - Only the sound on the CD layer can be

Windows Media^TMDigital Rights Management (DRM).

heard. The sound on the high-density Super Audio CD

layer cannot be heard.

• Playability of dual discs are not guaranteed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Color Systems

Structure of Disc/SD Card Contents

BD-video and DVD-video are recorded in different color

systems throughout the world. The most common color

system is NTSC (which is used primarily in the United

States and Canada).

The contents of BD / DVD / AVCHD are generally divided

into titles. Titles may be further subdivided into chapters.

BD / DVD / AVCHD

title 1

chapter 1

title 2

chapter 2 chapter 1 chapter 2 chapter 3

Region Codes

This unit has been designed to play back BD-video with

region “A” and DVD-video with region “1” or “ALL”. You

cannot play back BD-video or DVD-video that are labeled

for other regions. Look for the symbols on the right on your

BD-video or DVD-video.

Audio CD is divided into tracks.

audio CD

track 1

track 2

track 3

track 4

track 5

If these region symbols do not appear on your BD-video or

DVD-video, you cannot play back the disc in this unit. The

letter or number inside the globe refers to region of the world.

A BD-video or DVD-video labeled for a speciﬁc region can

only be played back in the unit with the same region code.

Data discs, USB device, SD Memory Cards containing MP3

/ WMA /JPEG are divided into folders, and the folders are

subdivided into ﬁles.

MP3 / WMA / JPEG

BD-video

folder (group) 2

file 4

folder (group) 1

file 1

file 2

file 3

file 5

DVD-video

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback

CAUTION:

playing a Disc

Keep your ﬁngers well clear of the disc tray as it is closing.

Neglecting to do so may cause serious personal injury.

This section shows you the basics on how to play a disc.

Basic playback

Preparations

• When you want to view a disc, turn on the TV and select the video input connected to the Blu-ray disc player.

To start playback in the stop mode

Press PlAY.

Press the ON/STANDBY button.

The Blu-ray disc player turns on.

To pause playback (still mode)

Press PAUSE during playback.

To resume normal playback, press the PlAY button.

Press OPEN/ClOSE.

• The sound is muted during still mode.

The disc tray opens.

To stop playback

Press STOP. The setup menu is displayed.

To resume normal playback, press

ROM, then press OK.

to select DVD/BD-

Place the disc on the disc tray.

• Depending on the disc, playback starts where it stopped

or at the beginning of the disc.

With the playback side

down

If you press STOP twice, playback stops completely.

To stat playback again, press PlAY. Playback starts at

the beginning of the disc.

To remove the disc

Press OPEN/ClOSE.

Press OPEN/ClOSE to close the disc tray.

Playback starts.

Remove the disc after the disc tray opens

completely.

If you insert a Blu-ray disc or a DVD that contains

Be sure to press the OPEN/ClOSE button

to close the disc tray after you remove

the disc.

a top menu, a menu may appear. Use

to select the title you want to view, then press OK

to start playback.

• You may need to press the POPUP/TOP MENU or

MENU button to display disc menu (depending on

the actual Blu-ray disc or DVD.)

To turn the power off

Press ON/STANDBY button to turn the unit off.

Download from Www.Somanuals.com. All Manuals Search And Download.

Variable Speed playback

You can play discs at various speeds, and resume playback from the location where you stopped playback.

Playing in fast reverse / forward directions

To resume normal playback

Press

during playback.

Press

PlAY.

: Fast forward playback

: Fast reverse playback

Notes:

• The Blu-ray disc player mutes sound and subtitles during

reverse and forward scan of DVDs.

• The playback speed may differ depending on the disc.

Each time you press this button, the fast-forward

or fast-reverse speed changes in the following

sequence:

Fast x 2

Fast x 4

Fast x 8

Fast x 16

Fast x 32

Fast x 64

Fast x 128.

Playing frame by frame

To resume normal playback

Press

during still playback.

Press

PlAY.

Each time you press this button, the picture

advances one frame.

Note:

• The sound is muted during frame by frame playback.

Playing in slow-motion

To resume normal playback

Press

during playback.

Press

PlAY.

Each time you press this button, the slow-

motion speed changes in the following

sequence:

Notes:

• The sound is muted during slow-motion playback.

• 3 speeds are available.

Slow x 1/2

Slow x 1/4

Slow x 1/8

locating a Desired Section

Normally, Blu-ray discs and DVDs are divided into titles, and the titles are sub-divided into chapters. Audio CDs are divided

into tracks.You can quickly locate any speciﬁc title, chapter, or track.

locating a title using the top menu

Press

want.

to select the title you

Press POPUP/TOP MENU.

The top menu appears on the TV

screen.

If the titles in the top menu are assigned a number,

you can directly locate a speciﬁc title by pressing its

designated number with the number buttons.

e.g.

Press OK.

Playback starts from Chapter 1 of the selected title.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback

locating a speciﬁc chapter or track

Press

repeatedly to access the

and

refer to item

26 and item 10 on page 9 and

page 8 respectively.

chapter or track number you want.

Playback starts from the selected chapter or track.

You can also press

To locate succeeding chapters or tracks.

(shown as in the right

illustration) on the remote

control to access the desired

chapter or track.

Playback starts from the beginning of the

current chapter or track.When you press twice

in quick successions, playback starts from the

beginning of the preceding chapter or track.

Note: Some titles may not display chapter numbers.

Accessing a Speciﬁc location Directly

locating a speciﬁc title/chapter/time

Press GOTO.

(Press GOTO once)

The Goto menu appears on the TV screen.

Goto Track:

/ 21 (Current: 10)

e.g.

the currently

playing track

number

the desired

track number

the total

track number

a. Press the GOTO button once:

(Press GOTO twice)

Goto Title:

/ 4 (Current: 1)

Goto Time:

/ 01:50:46 (Current: 0:05:52)

the desired

title number

the total

title number

the currently

playing title number

the desired time

(hh:mm:ss)

the total time

the elapsed

time

Press the number buttons to enter title,

b. Press the GOTO button twice:

2_{chapter (track) number or time.}

(Press GOTO once)

Goto Chapter:

/ 30 (Current: 6)

the currently

playing chapter

number

Goto File:

the desired

chapter number

the total

chapter number

/ 21 (Current: 10)

the desired

ﬁle number

the total

ﬁle number

the currently

playing ﬁle number

While accessing the TIME using number buttons, just

enter 2 digits in order.

c. Press the GOTO button for 3 times:

The ﬁrst two numbers you entered represent hours.

The second two numbers you entered represent

minutes.

Goto Time:

/ 01:50:46 (Current: 0:05:52)

The third two numbers you entered represent seconds.

the desired time

(hh:mm:ss)

the total time

the elapsed

time

Press the ClEAR button to reset the numbers.

Press OK.

Playback starts from the selected section.

Download from Www.Somanuals.com. All Manuals Search And Download.

Repeating a Title, Chapter, Track or Speciﬁc Segment

Repeating a title, chapter or track

Press REPEAT repeatedly to select the

desired repeat mode during playback.

Repeat Off

Repeat All

Repeat Off

e.g.

Notes:

• The repeat setting will be cancelled when you stop

playback.

• The chapter, title or track repeat will be cleared when moving

to another chapter, title, track / ﬁle or folder.

• Repeat playback does not function during A-B repeat

playback.

Repeat Off

Repeat Title

Repeat Chapter

Repeat Off

• Chapter and title repeat are not available with some

scenes.

Repeat Track

Repeat All

• When the repeat setting is set for a MP3 or WMA folder (ﬁle),

the repeat setting will be canceled if you select other MP3 or

WMA folder (ﬁle) to playback.

Repeat Off

Repeat File

Repeat All

Repeat Off

Repeating a speciﬁc segment

To resume normal playback

Press A-B at the desired starting point

A during playback.

Press A-B until _{Repeat Off}is displayed.

Notes:

Repeat A-

• Some discs may not permit A-B repeat operation.

• You can specify a segment only within the current title or

track.

• You cannot set the A-B repeat function for a segment that

Press A-B at the desired ending point B

during playback.

includes multiple camera angles.

• A-B repeat does not function during chapter, title, track or all

repeat playback.

Repeat A-B

The DVD player automatically returns to point A

and starts repeat playback of the selected segment

(A-B).

playing in a Random order

Playing tracks or ﬁles in a random order

To resume normal playback

Press RANDOM repeatedly until “

Press RANDOM repeatedly to select

Random ON during playback.

” is displayed.

Random Off

Once you turn RANDOM function on, the RANDOM

indicator will be activated and the system will play all ﬁles

in a random sequence.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback

pIp (BoNUSVIEW) Setting

Some Blu-ray discs have the PIP function which enables you to display the secondary video in the primary video.You can call

up the secondary video by pressing BONUSVIEW whenever the scene contains the secondary video.See the documentation

that came with the disc for playback instructions.

Press BONUSVIEW during playback to

turn PIP mode on.

Primary video

BONUS VIEW

Press 2nd AUDIO to turn the audio for

Secondary video

2_{the video in the PinP window on or off.}

To resume normal playback

Press BONUS VIEW to turn off the PIP mode.

Press 2nd SUBTITlE to turn the subtitle

for the video in the PinP window on or

off.

Note:

• PIP audio cannot be heard unless Bitstream Mixed has been

selected on the Audio menu.For more information, see“Audio

Setting” on page 31.

Camera Angle

Some BD-video and DVD-video contain scenes which have been shot simultaneously from various angles.

The selected angle will be displayed on the display bar

at the top of the TV screen.

During playback, press ANGlE.

Angle

1/3

The ﬁrst digit indicates the current viewing angle, and

the second digit indicates the total number of viewing

angles.

Press , then use

to select the

2_{desired angle.}

Audio Selection

In the example “01/03 ENG Dolby TrueHD”,

During playback, press AUDIO.

“01” indicates the currently selected audio channel.

“03” indicates the total number of audio channels.

“ENG” indicates the audio language.

“DolbyTrueHD”describes the currently selected audio

format.

Press , then use

to select the

desired audio language and audio

format.

Notes:

• The available options of Audio vary from different disc

format.

• PIP Subtitle is not available for all discs. It only applies to

Audio

01/03 ENG Dolby TrueHD

PIP Audio

Blu-ray discs that supports picture-in-picture features.

Download from Www.Somanuals.com. All Manuals Search And Download.

Subtitle Selection

In the example “01/07 ENG”,

During playback, press SUBTITlE.

“01” indicates the currently selected subtitle.

“07” indicates the total number of subtitles.

“ENG” indicates the subtitle language.

Press , then use

desired subtitle.

to select the

Notes:

• The available options of Subtitle vary from different disc

format.

Subtitle

01/07 ENG

• PIP Subtitle is not available for all discs. It only applies to

Blu-ray discs that supports picture-in-picture features.

PIP Subtitle

Displaying on-screen Information

You can check information about the current disc by pressing

On-Screen display

Disc format

On-Screen Display

Title 1 Chapter 1/25

BD-ROM

0:02:00

1:57:35

Off

Play

Title 1 Chapter 1/18

0:02:00

DVD

1:57:35

Track 1/12

0:00:20

CD-DA

0:05:35

Off

File: 1/5 song1.mp3

Title: Cool Track

Artist: Ricardo Funiccio

Album: Dead Dux

Off

Play

0:02:00

0:30:00

File: 4/13 flower.jpg

Pause

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback

playing AVCHD/Mp3/WMA/JpEG Files

You can play AVCHD, MP3, WMA or JPEG ﬁles that have been recorded on a disc on the Blu-ray disc player.

Playing ﬁles on a data disc

When you insert a data disc containing picture, music, or video ﬁles into your player, icons are added to the menu to

indicate that video, music, or picture ﬁles are available for playback.

If a USB device and a SD card containing music

are inserted at the same time, the system will

enter the source selection screen shown as

below:

Press OPEN/ClOSE to open the disc

tray, place a disc that contains video/

MP3/JPEG Files.

A selection menu will appear on the screen.

Music

Video

USB1

2 item(s)

Settings

Blockbuster

Netflix

Optical Disc

SDIO

Main Menu

Connected

Pandora

Browse Pictures

Now Playing

Vudu

Music

Pictures

For SD card and USB device operation, please

refer to “Using an SD card”on page 27 and “Using

a USB Device” on page 28.

Press

to select the Music or

Pictures, and then press OK.

(For example: selecting the Music)

Press / to select the desired MP3 ﬁle,

and then press OK to start playing.

If no USB device or SD card is inserted, the system

will directly access the following screen:

File: 1/5 song1.mp3

Title: Cool Track

Artist: Ricardo Funiccio

Album: Dead Dux

Music

0:02:00

0:30:00

Off

Play

Optical Disc

10 item(s)

: Press RANDOM repeatedly to turn random

playback on or off.

File

Information

Playlist

Main Menu

:Press REPEAT repeatedly to select the

desired repeat mode.

Play Files

Browse Pictures

Now Playing

To view JPEG picture ﬁles while playing

music ﬁles, follow the following steps:

1. Press RETURN.

2. Use

to select Browse Pictures, then

press OK.

: displays source (Optical Disc/USB/SD) device name.

: deﬁnes the total number of ﬁles that a device contains.

: shows all ﬁles name.

3. Select the desired JPEG ﬁle and press OK to

start viewing.

: shows the information on the currently selected ﬁle.

Download from Www.Somanuals.com. All Manuals Search And Download.

Slide Show Effects

Slide Show Delay

None

No Delay

Pictures

Optical Disc

30 item(s)

Main Menu

Settings

Main Menu: Returns to the main menu.

Thumbnail

Media Menu

Media Menu: Returns to select the source. This item only

appears if your optical disc, USB device or SD card is

inserted.

Start Slide Show

Browse Music

Previous Folder:This item only appears if your optical disc,

USB device or SD card contains several different picture

folders.

Now Playing

File: 13/30

Start Slide Show: This option enables you to view picture

(ﬁles) one after another automatically.

: displays source (Optical Disc/USB/SD) device name.

: deﬁnes the total number of ﬁles that a device contains.

: shows the currently playing ﬁle number.

Browse Music: Goes back to Music folder.

To stop playing and return to the main

menu,follow one of the steps described

below:

• Press STOP.

: shows all pictures in thumbnail mode.

Settings: This option enables you to deﬁne Slide Show

Effects (None, Horizontal Scroll, Fade and Shutter) and

Slide Show Delay (5 Seconds, 2 Seconds, 1 Seconds,

No Delay, 10 Seconds, 15 Seconds and 30 Seconds).

After setting, press to highlight Ok and then press OK

to conﬁrm.

• Press RETURN.

• Press , then use

to highlight Main Menu

and then press OK to conﬁrm.

Using an SD Card

This unit supports the use of a Secure Digital (SD) card (not

included).

CAUTION:

Before inserting the SD card, please read carefully the

relevant information on “Playable Discs and Files” on

page 18.

Inserting an SD card

If no USB device or optical disc containing music or pictures is

inserted, the system will directly load the data on the inserted

SD card. Otherwise, it will enter the source selection screen.

If so, please follow the operation instructions in “Playing ﬁles

on a data disc” on page 26 for details.

Inserting an SD card fully into the slot

on the front of Blu-ray disc player until

it clicks as illustrated.

To pause playback

Press during playback. To resume normal playback,

press PlAY.

To stop playback

Press STOP.

SD/SDHC

Card

Removing the SD card

In stop mode, gently push the SD card into the slot and

then pull it out slowly.

Press

and then press OK.

to select Music or Pictures,

Notes:

•

If you cannot easily insert the memory card, you may have

inserted it incorrectly.Try to turnover the card and then insert

again. Do not force the memory card into the memory card

slot.

•

Do not remove the SD card during playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback

Using a USB Device

You can play video, MP3 or JPEG ﬁles that have been stored on USB devices on the Blu-ray disc player.

Operating a USB device

To pause playback

Press during playback. To resume normal playback,

press PlAY.

Inserting a USB device into the USB

slot on the back of Blu-ray disc player

until it clicks.

To stop playback

Press STOP.

Press

to select Video, Music or

Removing the USB device

In stop mode, gently pull the USB device out slowly.

Pictures, and then press OK.

If no optical disc or SD card containing music or

pictures is inserted, the system will directly load

the data on the USB device. Otherwise, it will enter

the source selection screen. If so, please follow the

operation instructions in “Playing ﬁles on a data

disc” on page 26 for details.

Notes:

• If you cannot easily insert the USB device, you may have

inserted it incorrectly. Try to turnover the device and then

insert again.

• Do not remove the USB device during playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

Customizing the Function Settings

You can change the default settings to customize performance to your preference.

IP Settings

General Operations

Link Status

MAC Address

IP Mode

Link Down

00:23:18:75:b1:2b

Dynamic

0.0.0.0

1. Press

to select Settings in home menu while in full

stop mode, the Settings menu appears.

IP Address

Subnet Mask

Gateway

2. Press button, then use

options.

button to select the setting

0.0.0.0

3. Press OK button.

0.0.0.0

4. Press

menu.

or RETURN button to return to the previous

Primary DNS

Secondary DNS

0.0.0.0

Home Menu

Apply

Cancel

Network

Info

BD-ROM

2. Press

3. Press

to select IP Mode, then press OK.

Display

to select an IP mode.You can select:

Quick Setup

HDMI Status

Connected

1080p(HDMI)

HDMI Auto

16:9 Pillarbox

Off

HDMI Preferred Format

Resolution

• Off — Disables the network interface.

• Manual — Lets you manually configure network

settings, such as IP address, subnet mask, and

gateway settings.

Settings

Display

TV Aspect

Film Mode

Audio

Deep Color

Connected

• Dynamic — Uses DHCP to automatically obtain an IP

address.

Speaker

4. Press or RETURN to go to the previous menu.

Language

Info Menu

Settings menu items submenu display area

This menu displays the following information:

Network Connection Setting

•

Software Version

Software Date

•

Netﬂix ESN

1. Press

to select Network in stop mode, the network

1. In the main menu of Settings, press button, then use

button to select Info to display the version information

connection menu appears.

on software and hardware.

Wired

2. Press or RETURN to go to the previous menu.

Wireless

Performing Quick-Setup

Network Test

1. In the main menu of Settings, press button, then use

button to select Quick Setup, and then press OK

to conﬁrm.

2. Press button, then use

button to select the desired

connection setting.

2. Press OK to perform Quick Setup.

To exit the setup menu:

3. Press OK button.

• Use button to highlight “No thanks.I’ll go through the

full setup menu later”, and then press OK.

• Or press button directly.

Note: The option Wireless appears only while a wireless

LAN adapter is inserted into the USB slot.

3. Follow the on-screen instructions to customize the

following settings to your preference:

Conﬁguring a wired Internet connection

•

OSD language Settings

•

Resolution

1. Press

to select Wired, then press OK to conﬁrm.

The IP Settings screen appears.

TV Aspect

If the network connection is active, link Up appears next

to Link Status. If the network connection is not active,

link Down displays next to Link Status.

4. After setting, press OK to conﬁrm and exit the setup.

Download from Www.Somanuals.com. All Manuals Search And Download.

Function setup

Customizing the Function Settings

TV Type

Resolution

Display Setting

If your TV is a high-deﬁnition TV(HDTV)

connected to the HDMI jack on your

player and you want your player to set

the output resolution based on informa-

tion exchanged between the TV and your

player over the HDMI cable.

1. In the main menu of Settings, press button to select

HDMI Auto

Display, and then press OK to conﬁrm.

Display

If the TV is a high-deﬁnition TV (HDTV)

capable of 1080p (any frame rate) con-

nected to the HDMI jack on your player

1080p (HDMI)

HDMI Status

HDMI Preferred Format

Resolution

Connected

1080p(HDMI)

HDMI Auto

16:9 Pillarbox

Off

If your TV is a high-deﬁnition TV (HDTV)

capable of 1080i only

1080i

720p

480p

480i

If your TV is a high-deﬁnition TV (HDTV)

capable of 720p only

TV Aspect

If your TV is an enhanced-deﬁnition TV

(EDTV)

Film Mode

If your TV is a standard-deﬁnition NTSC

TV (American or Asian SD TV)

Deep Color

TV Aspect:

2. Press

3. Use

to select an option, and then press OK.

16:9 wide, 16:9 Pillarbox, 4:3 Pan and Scan and 4:3 letter

Box are available for your choice.

to select the desired option, and then press

OK to conﬁrm your selection.

Film Mode:

4. Press to go to the previous menu.

Movies are recorded on ﬁlm at a rate of 24 pictures (frames)

per second.Many of the movies on Blu-ray discs are placed

on the discs at this frame rate.If yourTV supports 24 frames

per second, but you would prefer viewing the video at a

higher frame rate, you should turn off Film Mode.Off selects

a 60 frames/second output format.

HDMI Status:

This option displays the HDMI status. If an HDMI TV is

connected, Connected appears. If an HDMI TV is not

connected, Disconnected appears.

HDMI Preferred Format:

Deep Color:

This option shows the best HDMI format for the connected This option decides whether to turn off the Deep Color

TV.

(color depth) setting for video signals output from the HDMI

OUT jack.

Resolution:

Connecting the player and a TV that supports Deep

Color allows more accurate color reproduction than when

connecting it to a TV that does not support Deep Color. It is

recommended to set this option Off if the picture is unstable

or colors appear unnatural.

You can deﬁne the video output resolution in this option. In

case that the menu of “Resolution”setting disappears, make

composite video (yellow) connection to restore it, then select

the resolution which is compatible with the connected TV.

Notes:

•

Selecting a resolution the TV does not support could

result in an unstable picture or loss of the picture. See

the documentation that came with the TV to ﬁnd the

resolutions the TV supports.

•

Only the HDMI output on your player supports 1080p

video output at any frame rate. If the TV is connected

to the component output, the video output is limited to

1080i or lower.

Download from Www.Somanuals.com. All Manuals Search And Download.

Customizing the Function Settings

Digital Output:

Audio Setting

•

PCM Stereo — Sets the output to PCM Stereo if you

have not an audio receiver connected to your Blu-ray

dsic player or the audio receiver connected to Blu-ray

disc player is not a 5.1/7.1 channel receiver.

The settings in the Audio menu will conﬁgure the BD player’s

digital audio outputs (HDMI or Optical).

•

Bitstream HD — Lets your player send Dolby TrueHD

or DTS-HD MA bitstreams over HDMI (if your player is

connected to a compatible HDMI audio receiver). If your

player is not connected to a compatible HDMI receiver

(for example, your player is connected directly to the TV

or your player is connected to an audio receiver using an

optical cable), a compatible audio signal is automatically

sent over the HDMI and optical connections. With this

setting, Blu-ray audio is limited to the soundtrack for the

main movie (no PIP audio).

1. In the main menu of Settings, press button, then use

button to select Audio, then press OK button.

Audio

PCM Downsampling

48 kHz

PCM7.1

Digital Output

•

Bitstream legacy — Sends a DTS or Dolby Digital

bitstream from the disc over the HDMI and optical

connections. Blu-ray audio is limited to the soundtrack

for the main movie (no PIP audio).

Dynamic Range Control

Bitstream Mixed — Sends a mixed (PIP audio and movie

audio) DTS audio stream over the HDMI and optical

connections.This mode is primarily intended for use when

you want to hear both PIP audio and the movie audio.

•

PCM 5.1 — Sends a PCM audio signal of up to 5.1

channels over the HDMI connection and up to 2 channels

over the optical connection.

2. Press

3. Use

to select an option, and then press OK.

PCM 7.1 — Sends a PCM audio signal of up to 7.1

channels over the HDMI connection and up to 2 channels

over the optical connection.

to select your preferred audio items, and then

press OK to conﬁrm your selection.

4. Press to go to the previous menu.

Dynamic Range Control:

PCM Downsampling:

Dynamic Range Control means that you can allow the BD

player to make the loud parts of a movie’s audio track quieter

than they would be in the theatre, without making the dialog

of the actors any quieter.

Ifyoudon’thaveasurroundsoundreceiverconnectedto

the BD player, you should leave the PCM downsampling

to 48 Khz, and proceed to the next setup menu item. This

is true regardless of whether the audio is connected to the

TV with HDMI or the analog stereo outputs.

This would be useful, for instance, when you want to watch

a movie in the evening when others might be sleeping.

If you have a surround sound receiver connected to

the BD player, and you have connected to the surround

receiver via the BD player’s analog multichannel audio

outputs, this setting has no effect on the audio going to the

analog outputs of the player.Leave the PCM downsampling

to 48 KHz, and proceed to the next setup menu item.

NOTES: This setup menu item has no effect unless:

•

The device playing the disk’s audio (TV or surround audio

receiver) is connected to the BD player’s analog audio

outputs; OR

•

you have selected “Bitstream Mixed” in the BD player’s

audio setup menu.

If you have a surround sound receiver connected to

the BD player, and you have connected to the surround

receiver via the BD player’s HDMI output, this setting has

no effect on the audio going to the HDMI output of the player.

leave the PCM downsampling to 48 Khz, and proceed to

the next setup menu item.

When Dynamic Range Control is set to Off, movie

soundtracks are played with the standard dynamic range.

When movie soundtracks are played at low volume or from

smaller speakers, you can set Dynamic Range Control to

On. Your player applies appropriate compression to make

low-level content more intelligible and prevent dramatic

passages from getting too loud.

If you have a surround sound receiver connected to

the BD player via optical cable, set this menu item to the

maximum PCM sampling rate that your surround receiver

can accept (48 KHz or 96 Khz). If in doubt, consult your

surround receiver’s manual or set to 48 KHz.

Selecting the “Auto” option turns on the Dynamic Range

Control for all BD movie soundtracks except Dolby TruHD. If

you have selected a TruHD track on the BD disk, the “auto”

selection tells the BD player to only turn on dynamic range

control if information embedded in the TruHD sound track

tells it to do so.

NOTE: Incorrectly setting the digital audio output’s PCM

sampling rate too high may result in unpredictable audio

playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

Function setup

Customizing the Function Settings

5. Press

to choose the desired audio signal.You can

Speaker Setting

select between Pink, 1kHz Sine and White.

6. Press OK to begin the speaker test.The audio signal will

be sent to a different speaker every approximately every

two seconds.The audio test will highlight which speaker

is supposed to be getting the sound on the screen.

Once the speakers are connected to the system and properly

conﬁgured, you can check to verify that the connections

to the speakers are correct by running an audio speaker

test.

7. To stop the audio test, press one of the

buttons.

To run this test, follow the instructions described as below:

8. Press or RETURN to go to the previous menu.

1. In the main menu of Settings, press button, then use

button to select Speaker, then press OK.

Note: This setup menu item has no effect unless:

•

If you have selected ‘Bitstream Mixed’ in the audio

menu, these menu choices will have no effect. (Each

channel’s full audio spectrum will be sent to each speaker,

regardless of the speaker size selected)

If you don’t know the type of speakers attached to your

surround sound system, consult the manual for your

speaker system.

2. Use

to highlight the desired speaker, then

press OK to enter.

3. Press to choose the desired audio signal, and then

press OK to conﬁrm.

Front left & Right Speakers:

•

By setting the front left speaker’s size, the front right

speaker’s size is automatically changed to match.

•

The front speakers can not be turned off. They can only

be set to ‘Small’ or ‘large’.

Center Speaker:

•

If the front speakers have been set to small, the center

speaker can only be set to ‘small’ or ‘Off’.

•

Setting a speaker to ‘off’ will result in no sound being

delivered to that speaker.

Subwoofer:

•

If you don’t know the crossover frequency of your

subwoofer, consult the manual for your speaker

system.

Surround left & Right Speakers:

•

By setting the left surround speaker’s size, the right

surround speaker’s size is automatically changed to

match.

•

If the front speakers have been set to small, the surround

speakers can only be set to ‘Small’ or ‘Off’.

Rear left & Right Speakers:

•

By setting the left rear speaker’s size, the right rear

speaker’s size is automatically changed to match.

•

If the front speakers have been set to small, the rear

speakers can only be set to ‘Small’ or ‘Off’.

4. Use

to move the highlight box to the Test

button on the bottom, then press OK. A message will

appear.

Download from Www.Somanuals.com. All Manuals Search And Download.

Customizing the Function Settings

Notes:

language Setting

•

Not all languages are available on all discs.

Some discs do not let you select the audio language

using your player’s menu.Instead, you have to select the

audio language from the disc setup menu (the menu that

appears after you insert the disc).

1. In the main menu of Settings, press

to select

language, and then press OK.

•

You can also select the subtitle language from the subtitle

menu in the on-screen menu.

Language

OSD

English

Auto

Parental Control

Audio

Subtitle

1. In the main menu of Settings, press , then press

to select Parental, and then press OK.

None

Parental

Parental Country

Parental Control

Parental Level

USA

Off

1 [Kid Safe]

2. Press

to select OSD, Menu, Audio or Subtitle, and

Parental Password

then press OK.

3. Use

to select your preferred language, and then

press OK to conﬁrm your selection.

4. Press to go to the previous menu.

OSD:

This option enables you to select the on-screen menu

language.

2. Press

3. Use

to select an option, and then press OK.

to select the desired option, and then press

Menu:

OK to conﬁrm your selection.

This option lets you to select the disc menu language.

4. Press to go to the previous menu.

Notes:

Note: If Parental Control was previously turned On, you will

be prompted to enter the parental control password before

being allowed to change these settings. (See “Turning

parental control on or off” on page 34 for details.)

•

Not all languages are available on all discs.

Most discs only have one menu language.

Audio:

You can choose the audio language from this option to your

preference.

Selecting the parental country

Notes:

If a Blu-ray Disc has parental rating systems for more than

one country, you can select the country you want to use.

•

Not all languages are available on all discs.

Some discs do not let you select the audio language

using your player’s menu.Instead, you have to select the

audio language from the disc setup menu (the menu that

appears after you insert the disc).

1. In the main menu of Settings, press , then press

to select Parental, and then press OK.

2. While the highlight bar is moved on Parental Country,

then press OK.

3. Press

to select the desired country, then press

Subtitle:

OK.

You can customize your preferred subtitle language in this

option.

4. Press to go to the previous menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Function setup

Customizing the Function Settings

Turning parental control on or off

System Setting

1. In the main menu of Settings, press , then press

to select Parental, and then press OK.

1. In the main menu of Settings, press button, then use

button to select System, then press OK.

2. Press

3. Press

to select Parental Control, then press OK.

to select On or Off, then press OK.

4. Press to go to the previous menu.

System

Optical Disc Auto Play

Setting the parental control level

BD-Live Internet Access

BD-Live Storage

Always Allow Access

USB (1.9GB Free)

1. In the main menu of Settings, press , then press

Erase Blu-ray Storage

Time Zone

to select Parental, and then press OK.

CST (GMT-06:00)

5 Minutes

2. Press

to select Parental level, then press OK.

Screen Saver Duration

CEC Support

3. Press

to select the rating level you want to block,

Update Via Network

Restore factory defaults

Required Storage: 84 MB

then press OK. The rating and all higher ratings will be

blocked.You can select:

•

1 [Kid Safe] — Suitable for all children.

2 [G] — General audiences.

3 [PG] — Parental guidance suggested.

4 [PG-13] — Not suitable for anyone under 13.

5 [PG-R] — Parental guidance recommended.

6 [R] — Not suitable for anyone under 17 unless

supervised by a parent or adult guardian.

7 [NC-17] — Not suitable for anyone under 17.

8 [Adult] — All DVDs can be played.

2. Press

3. Use

to select an option, and then press OK.

to select the desired setting, and then press

OK to conﬁrm.

4. Press to go to the previous menu.

•

Optical Disc Auto Play:

Note: These ratings are only for DVDs.

If On is selected, it will load data and play back automatically

when you insert a Blu-ray disc. When Off is selected and

if you insert a Blu-ray disc, the disc you can select will be

displayed on the Settings menu.

4. Press to go to the previous menu.

Setting the parental control password

BD-live Internet Access:

1. In the main menu of Settings, press , then press

•

limit Access — Allows Internet access with valid “BD-

Live” network access approval.

to select Parental, and then press OK.

2. Press

to select Parental Password, then press

Always Allow Access — Always allows BD-Live Internet

access.

OK.

3. Enter a 4-digit number for the parental password, then

Prohibit Access — Never allows BD-Live Internet

use to highlight Ok, and then press OK to conﬁrm.

access.

If you forget your password, reset your player to the

factory defaults. For more information, see “Restore

factory defaults” on page 35.

BD-live Storage:

This option is used to tell the BD player whether or not to

use an inserted SD card or USB device to store BD-Live

content (movie trailers, additional scenes, etc.).

4. Press to go to the previous menu.

For detailed operation, please refer to “Using BD-live^TM

Features” on page 38.

Erase Blu-ray Storage:

If you choose OK to erase Blu-ray storage, all bookmarks

and BD-Live content saved in memory are deleted.

Time Zone:

This option allows you to select the desired time zone.

Download from Www.Somanuals.com. All Manuals Search And Download.

Customizing the Function Settings

Screen Saver Duration:

This Blu-ray disc player has a screen saver feature that turns the screen black when your player is inactive.You can set

the interval time you want your player to wait before activating the screen saver.

CEC Support:

This option is used to allow the TV remote control to control certain functions of the Blu-ray disc player; and for the Blu-ray

player to control certain functions of the TV.

Note: Not all TVs are compatible with your Blu-Ray Player.

On: Allow mutual control of devices through HDMI.

Off: Do not allow CEC control.

Update Via Network:

This option displays the required storage space if the BD player is connected to internet for upgrade.

For detailed upgrade operation, please refer to “UpgradingYour Player’s Firmware” on this page.

Restore factory defaults:

Choose one of the following 7 options, then press OK to pop up a dialog box, choose Ok in the box, and then press OK

to conﬁrm.

To apply the deactivation, please plug off the player after operating deactivation.

Actions

Response

Restore factory settings and deactivate All settings (including Parental Password) will be restored to the factory

all connected applications

defaults and all connected applications will be deactivated.

Restore factory settings

Restores all settings (including Parental Password) to the factory

defaults.

Deactivate all connected applications

Deactivates all connected applications (Netﬂix / Pandora / Blockbuster

/ VUDU)

Deactivate Netﬂix

Deactivate Pandora

Deactivate VUDU

Deactivates the connected Netﬂix application

Deactivates the connected Pandora application

Deactivates the connected VUDU application

Deactivates the connected Blockbuster application

Deactivate Blockbuster

Upgrading Your player’s Firmware

The company that produced this player may occasionally offer upgrades to the player’s software.

Automatic upgrades over the Internet

1. Make sure that your player is successfully connected to the Internet.If new software is available, you will see a message

prompting you whether to update your ﬁrmware.

2. If you want to update the player’s ﬁrmware, use

to highlight “OK”, and then press OK. The software will begin

downloading, and a status bar will appear on the TV screen.

3. Once the update is complete, a message will appear indicating that the player will turn itself off and on.

Download from Www.Somanuals.com. All Manuals Search And Download.

Function setup

Using the Connected Applications

Some players are equipped with the capability to watch movies over the internet (from Blockbuster, Netﬂix or Vudu), or

to listen to Pandora internet radio.

Watching Movies with Netﬂix™

To use Netﬁx service, connect this player to your network,

and make the network settings if they are not ﬁnished yet.

1. Launching Netﬂix movie

In Home Menu, press

, and then press

to select Connected, then use

to highlight “Netﬂix”, and then

press OK to enter.

Video

4. Preparing Instant Queue

Settings

Blockbuster

Netflix

To play streaming video via Netﬁx service, Netﬁx player

needs to be activated. Read the instructions displayed on

the TV screen, and visit http://www.netﬁx.com/activate on

your PC. Sign in to your Netﬁx account, if necessary. Enter

the activation code displayed on the TV screen.

Connected

Pandora

Vudu

Music

Now you can view Netﬁx streaming video.

After having activated Netﬁx player and prepared Instant

Queue, movies and TV episodes in your Instant Queue

appear on the TV screen. Select your desired one using

the remote control of the player. You can control Netﬁx

streaming video with the following keys of the remote control

of this player:

Pictures

2. Creating Netﬂix account

To start playing movie.

To pause playback while in PLAY mode.

If you are not a Netﬁx Member:

Select “no”. Read the instructions displayed on the TV

screen, and visit http://www.netﬁx.com/toshiba from your

PC. Sign up to create your account, then select “I’m now

a member”.

To stop playing and return to a list of

movie titles.

To pause playing movie.

To start playing while in PAUSE mode.

To pause playing and open a list of

scenes. Pressing further proceeds to the

next scene.

To pause playing and open a list of

scenes. Pressing further proceeds to the

previous scene.

To stop playing and return to a list of

movie titles.

To pause playing and open a list of

scenes. Fast forward play starts.

If you are a Netﬁx Member:

Select “Yes”.

To pause playing and open a list of

scenes. Fast reverse play starts.

HOME MENU To stop playing and return to Home Menu.

3. Activating Netﬂix player

To pause playing of Trick play screen

while in PLAY mode.

To start playing the movie in case of dur-

ing Trick play screen.

To play streaming video via Netﬁx service, Netﬁx player

needs to be activated. Read the instructions displayed on

the TV screen, and visit http://www.netﬁx.com/activate on

your PC. Sign in to your Netﬁx account, if necessary. Enter

the activation code displayed on the TV screen.

Note:Resolution of video streamed from Netﬂix varies depending

on communication speed or bitrate of each content, etc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Connected Applications

Watching Movies with BlOCKBUSTER^®

This Blu-ray Disc Player enables you to use the following services provided by Blockbuster.

1. In Home Menu, press

2. Press , then press

to select Connected.

to highlight Blockbuster, and then press OK to enter Blockbuster main menu.

• Movies : Display movies.

• TV Shows : Display TV Shows.

• Find : Search for a desired movie or TV show by entering it manually.

• My library : Display a title that you bought or rented.

• My Favorites : Displays a title that has been added to My Favorites.

• Confgure : Activate or deactivate the Blu-ray Disc Player.

• Help : Get customer service contact information and check the current software version.

3. If you don’t have a Blockbuster account yet, visit www.blockbuster.com to create your account.

4. Use

to select the Conﬁgure, then press OK.

5. Use the number buttons on the remote control to enter the activation code that is created by the web site, then use

to highlight Activate, and press OK to conﬁrm.

When the Blu-ray Disc Player is activated, you will move to the Home page.

6. Press

7. Press

8. Press

9. Press

to select the Movies or TV Shows, then press OK.

to select the desired title, then press OK.

to select the Rent or Buy, then press OK.

to select the Submit Order, then press OK. If you want to play any of the titles that your bought, simply

click Play Now.

10.Press to go to the previous menu.

Watching Movies with VUDU™

Creating a VUDU account on your player

1. In Home Menu, press

2. Press , then press

to select Connected.

to highlight Vudu, and then press OK to conﬁrm.

3. Follow the instructions to create an account, it will ask for an email address.

4. Enter YOUR email address using the keyboard that appears on the screen. VUDU will then display a message on the

TV “Sending you an email”.

Creating a VUDU account on your PC

1. VUDU will send you an email with a hyper-link; click on the link.

2. In the Vudu page that comes up on your PC’s browser after clicking the link, enter the e-mail and password of the

owner of the account.

3. VUDU will then display a message “Enabling your device to view movies.The email message on yourTV screen

will disappear when done”.

4. On your TV, you can now navigate to a VUDU movie, and ‘buy’ or ‘rent’ it.

Download from Www.Somanuals.com. All Manuals Search And Download.

Function setup

Using the Connected Applications

listening to Music with PANDORA™

Using an existing Pandora account

1. In Home Menu, press

2. Press , then press

to select Connected.

to highlight Pandora, and then press OK to conﬁrm.

3. Select “I have a Pandora account” from the option list.

4. Sign in with your test account.

Creating a new account on the BD player

1. In Home Menu, press

2. Press , then press

to select Connected.

to highlight Pandora, and then press OK to conﬁrm.

3. Select “I am new to Pandora” from the option list.

4. You will be given an activation code. Use this activation code to generate a new account and link it to the BD player

using a PC.

Creating a new Pandora account on your PC

Go to http://www.pandora.com/ to create a new account.

Using BD-Live^™Features

Some (but not all) BD disks contain additional features that are made available to players that are connected to the internet,

and have additional memory added. These additional features may include things like:

•

the ability to download new movie trailers

additional ‘commentary’ by actors and directors

multiperson game play and chat

In order to access BD-Live functions, the player must be properly conﬁgured for BD-Live internet access, and it must be

equipped with additional memory.

Adding BD-live memory to the player

In order to set the player up for BD-Live Internet Access, insert an USB device or SD card (1GB is recommended) into

the USB slot or SD card slot on the player.

Conﬁguring the player for BD-live internet access

In order to set the player up for BD-Live Internet Access, perform the following steps:

1. In the main menu of Settings, press button, then use

to select System, then press OK.

to select “BD-live Internet Access”, and then press OK.

to select the desired setting, and then press OK to conﬁrm.

2. Press

3. Use

4. Make sure that “limit Access” or “Always Allow Access” is checked.

5. Once the USB device or SD card has been inserted, if there is not at least 100Mbyte of free space on the device, you

should choose “Erase Blu-ray Storage” from the System setup menu.

6. Press to return to the main menu of Settings, then use

to highlight Network, and then press OK. (For details,

please refer to “Network Connection Setting” on Page 29.)

Note:

•

Depending on your connection environment, it may take time to connect to the Internet or the Internet may not be

connected.

When BD-Live function are used and the unit is connected to the Internet, you may be charged for this

communication.

Do not remove the USB device or SD card when using the BD-Live function.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Troubleshooting & Maintenance

Troubleshooting

If the unit does not perform properly when operated as instructed in this manual, check the unit, consulting the following

checklist.

Problem

Solution

No power

- Check if the AC cord is properly connected.

- Unplug the AC cord once, and wait for 5-10 seconds and then plug it in again.

No sound or picture

Distorted picture

- Check if the connected TV is turned on.

- Check if the connections are made securely and correctly.

- Check whether the connected TV or other device supports HDCP. (This unit will

not output a video signal unless the other device supports HDCP.)

- Check whether the output format of this unit (HDMI FORMAT) matches the

supported input format of other connected device.

- Sometimes a small amount of picture distortion may appear. This is not a

malfunction.

- Connect this unit directly to the TV. If the composite audio / video cables are

connected to a VCR, pictures may be distorted due to the copyright protection

system.

Completely distorted picture or black

/ white picture with BD / DVD

- Make sure the disc is compatible with this unit.

No sound or distorted sound

- Adjust the volume.

- Check if speakers are connected correctly.

- Check the HDMI connections.

- Check the settings in “Audio” menu.

Picture freezes momentarily during

playback

- Check the disc for ﬁngerprints / scratches and clean with a soft cloth wiping from

center to edge.

- Clean the disc.

Disc cannot be played back

- Clean the disc.

- Ensure the disc label is facing up.

- Check if the disc is defective by trying another disc.

- Cancel the ratings control or change the control level.

- Insert a correct disc that can be played back on this unit.

SD Memory Card cannot be read

- The format of the card does not match that accepted by this unit or the card is not

compatible.

No return to start-up screen when

disc is removed

- Reset this unit by turning it off, then on again.

The unit does not respond to the

remote control

- Aim the remote control directly at infrared sensor window on the front panel.

- Reduce the distance to infrared sensor window.

- Replace the batteries in the remote control.

- Re-insert the batteries with their polarities (+ / - signs) as indicated.

Buttons do not work or the unit stops

responding

- To completely reset the unit, unplug the AC cord from the AC outlet for 5-10

seconds.

The unit does not respond to some

operating commands during playback

- Operations may not be permitted by the disc.

Refer to the instructions of the disc.

The unit cannot read BD / DVD/ CD

- Dew condensation may form inside the unit. Do not use this unit for at least a few

hours until its inside gets dry.

- Wipe the dirt off the disc or replace the disc.

Angle does not switch

- The angle cannot be switched for BD / DVD which do not contain multiple angles.

In some cases multiple angles are only recorded for speciﬁc scenes.

Playback does not start when the title

is selected

- Check the settings in “Parental” menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Troubleshooting & Maintenance

Problem

Solution

The password for rating level has

been forgotten

- If you forget your password, reset your player to the factory defaults and your

forgotten password will be cleared. For more information, see “Restore factory

defaults” on page 35.

Cannot connect to the network

- Check if the LAN cable connection is properly made.

- Turn on the modem or broadband router.

- Check if the broadband router and/or modem is correctly connected.

- Check the “Network Connection Setting”.

Cannot connect to the network while

my PC is connected to the network

- Check the content of your Internet service contract to see if your Internet service

provider prevents multiple terminals connecting at the same time.

Cannot use the BD-Live function

- Use an SD card with enough space.

The playback of BD-video or

download of data does not perform

properly

- Check if an SD Card is correctly inserted. Do not remove the card during playback

as some BD-videos require an SD Card during playback.

Notes

•

Some functions are not available in speciﬁc modes, but this is not a malfunction. Read the description in this manual for details

on correct operations.

•

Some functions are prohibited on some discs.

Maintenance

Servicing

• Please refer to relevant topics on “Troubleshooting & Maintenance” before returning the product.

• If this unit becomes inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn

off, unplug the power plug, and please call our helpline to locate an Authorized Service Center.

Cleaning the cabinet

• Never use a solvent, thinner, benzene or alcohol to clean the unit. Do not spray insecticide liquid near the unit. Such chemicals

may discolor the surface or damage the unit.

Cleaning discs

• When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center to out. Do not wipe in a circular

motion.

• Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic

spray intended for analog records.

Cleaning the disc lens

• If this unit still does not perform properly although you refer to the relevant sections and to “Troubleshooting” in this manual, the

laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the

laser optical pickup unit.

Disc handling

• Handle the discs so that ﬁngerprints and dust do not adhere to the surfaces of the discs.

• Always store the disc in its protective case when it is not used.

• Note that discs with special shapes (heart-shaped discs, octagonal discs, etc.) cannot be played back on this unit. Do not

attempt to playback such discs, as they may damage the unit.

IR signal check

• If the remote control is not working properly, you can use a digital camera (including a cellular phone with built-in camera) to

see if it is sending out an infrared signal.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Glossary

Analog Audio

Dolby Digital

An electrical signal that directly represents sound. Compare The system to compress digital sound developed by Dolby

this to digital audio which can be an electrical signal, but is an Laboratories. It offers you sound of stereo (2ch) or multi-

indirect representation of sound.

channel audio.

Aspect Ratio

Dolby Digital Plus

The width of a TV screen relative to its height.

Dolby Digital Plus is the next generation digital audio

Conventional TVs are 4:3 (in other words, the TV screen is compression technology developed as an extension to Dolby

almost square); widescreen models are 16:9 (the TV screen is Digital. Blu-ray Disc supports 7.1 multi-channel surround

almost twice as wide as it is high).

sound output.

AVCHD

Dolby TrueHD

AVCHD is a new format for high deﬁnition video camcorders Dolby TrueHD is a lossless coding technology developed for

which can record and play high-resolution HD images.

next generation optical discs. Blu-ray Disc supports 7.1 multi-

channel surround sound output.

BD-Java

DTS (Digital Theater System)

With some BD which support Java applications, you can enjoy

the interactive functions such as games or interactive menus.

DTS is a multi-channel surround sound system. By connecting

to DTS decoder, you can enjoy movie dynamic and realistic

sound like movie theater. DTS surround sound technologies

were developed by DTS, Inc.

BD-live

BD-Live is a BD-video (BD-ROM version 2 Proﬁle 2.0/Proﬁle

1.1) which contains new functions (e.g. Internet connection), in

addition to the BONUSVIEW function.

DTS-HD

DTS-HD is a lossless coding technology developed as an

extension of the original DTS Coherent Acoustics format. Blu-

ray Disc supports 7.1 multi-channel surround sound output.

Blu-ray Disc (BD)

Blu-ray Disc is a next generation optical video disc which is

capable of storing much more data than a conventional DVD

is. The large capacity makes it possible to beneﬁt from the

Gateway

features such as high-deﬁnition videos, multi-channel surround IP Address of the electronic devices (such as router) which

sounds, interactive menus and so on.

provide Internet access.

Chapter

HDMI (High-Deﬁnition Multimedia Interface)

Just as a book is split up into several chapters, a title on a BD- A digital interface between audio and video source. It can

video or DVD-video is usually divided into chapters.

transmit component video, audio, and control signal with one

cable connection.

Component Video Output

Hub

Each signal of luminance (Y) and component (P_B/C_B, P_R/C_R)

is independent to output so that you can experience picture

Color as it is.

A device used for connecting multiple device to the network.

Also, due to compatibility with progressive video (525p/480p),

you can experience higher-density picture than that in interlace

(525i/480i).

IP Address

A set of numbers which are assigned to devices participating

in a computer network.

Digital Audio

JPEG (Joint Photographic Experts Group)

An indirect representation of sound by numbers. During

recording, the sound is measured at discrete intervals (44,100

times a second for CD audio) by an analog-to-digital converter,

generating a stream of numbers. On playback, a digital-to-

analog converter generates an analog signal based on these

numbers.

JPEG is a method of compressing still picture ﬁles. You can

copy JPEG ﬁles on BD-RE/-R, DVD-RW/-R, CD-RW/-R or SD

Memory Card from a computer and play back the ﬁles in this

unit.

lAN (local Area Network)

DNS Server

A group of computer networks covering a small area like a

company, school or home.

A server which translates Internet domain names into IP

addresses.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Glossary

local Storage

Virtual Package

A storage area of sub contents for playing virtual packages on

BD-video.

The function which copies data to other media (local storage)

from the Internet and play the secondary video, secondary

audio and the subtitle at the same time. The method of the

playback varies depending on discs.

MP3 (MPEG audio layer 3)

MP3 is a method of compressing ﬁles.You can copy MP3 ﬁles

on BD-RE/-R, DVD-RW/-R, CD-RW/-R or SD Memory Card

from the computer and play back the ﬁles on this unit.

Windows Media™ Audio

Windows Media™ Audio is the audio compressing technology

developed by Microsoft.You can copy Windows Media™ Audio

ﬁles on BD-RE/-R, DVD-RW/-R, CD-RW/-R or SD Memory

Card from a computer and play them back on this unit.

PCM (Pulse Code Modulation)

The most common system of encoding digital audio, found

on CD and DAT. Excellent quality that requires a lot of data

compared to formats such as Dolby Digital and MPEG audio.

For compatibility with digital audio recorders (CD, MD and

DAT) and AV ampliﬁers with digital inputs, this unit can convert

Dolby Digital, DTS, and MPEG audio to PCM.

x.v.Color

“x.v.Color” is a promotion name given to the products that have

the capability to realize a wide color space based on the xvYCC

speciﬁcations and is a trademark of Sony Corporation.

Proxy Server

Proxy server is a server which acts as an intermediary between

a workstation user and the Internet to ensure security.

Region Code

Regions associate discs and players with particular areas

of the world. This unit will only play back discs that have

compatible region codes.You can ﬁnd the region code of your

unit by looking on the rear panel. Some discs are compatible

with more than one region (or all regions).

Router

A networking device which distinguishes the IP address

assigned to each device and routing and forwarding information

in the computer network.

Sampling Frequency

The rate which sound is measured by a speciﬁed interval to

turn into digital audio data. The numbers of sampling in one

second deﬁnes as sampling frequency.The higher the rate, the

better the sound quality.

Subnet Mask

A mask which is used to determine what subnet an IP address

belongs to.

Title

A collection of chapters on BD-video or DVD-video.

Track

Audio CD use tracks to divide up the content of a disc.The BD-

video or DVD-video equivalent is called a chapter. See also

“Chapter”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Speciﬁcations

General

Signal system

NTSC color

Power requirements

Power consumption

Dimensions (width x height x depth)

Weight

120 V AC, 60 Hz

23 W

430 x 58.5 x 209.7 mm

1.7 kg

Operating temperature

Operating humidity

41°F (5°C) to 95°F (35°C)

Less than 80 % (no condensation)

Terminals

Video output

RCA jack

1 Vp-p (75W)‌

Component video output

RCA jack x 3

Y: 1 Vp-p (75W)‌

P_B/C_B: 700 mVp-p (75W‌) P_R/C_R: 700 mVp-p (75W)‌

Video: 480i, 480p, 720p, 1080i

HDMI output

HDMI jack x 1

Video: 480i, 480p, 720p, 1080i, 1080p, 1080p/24F / Audio

L/R: 2 Vrms (output impedance: less than 1kW)

Audio output (Analog)

RCA jack x 2

Audio output (Digital)

Optical jack x 1

Digital connector

Multi channel audio output

RCA jack x 8

All channels: 2 Vrms (output impedance: less than 1kW)

USB terminal x 1

500mA

lAN terminal

100BASE-T

Note:

• The speciﬁcations and design of this product are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

limited United States Warranty

Digital Audio Video (“DAV”) Product - Exchange Warranty

Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original consumers in the United

States.

THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING

THIS DAV PRODUCT AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR

TRANSFEREE.

DAV PRODUCTS PURCHASED IN THE U.S.A. AND USED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT

LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.

DAV PRODUCTS PURCHASED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND

MEXICO, AND USED IN THE U.S.A., ARE NOT COVERED BY THESE WARRANTIES.

through simultaneous use of this DAV Product and connected

equipment;or to units that have been modiﬁed or had the serial

number removed, altered, defaced, or rendered illegible.

limited Warranty

TACP warrants this DAV Product and its parts against defects in

materials or workmanship for a period of ninety (90) days after

the date of original retail purchase.

(6) This warranty does not cover Product sold AS IS orWITH ALL

FAULTS.

DURINGTHISPERIOD,TACPWIllEXCHANGEADEFECTIVE

DAV PRODUCT WITH A NEW OR REFURBISHED DAV

PRODUCT WITHOUT CHARGE TO YOU. DURING THE

PERIODTHAT COMMENCES ONTHE DATETHAT IS NINETY

ONE (91) DAYS AFTER THE DATE OF ORIGINAl RETAIl

PURCHASE AND ENDS ON THE DATE THAT IS THREE

How to Obtain Warranty Services

If, after following all of the operating instructions in this manual

and checking the section “Before Calling Service Personnel,”

you ﬁnd that service is needed:

HUNDRED SIXTY FIVE (365) DAYS AFTER THE DATE OF (1) For instructions on how to obtain warranty service for

ORIGINAl RETAIl PURCHASE, TACP WIll EXCHANGE A

DEFECTIVEDAVPRODUCTWITHANEWORREFURBISHED

DAV PRODUCT FOR A FEE.

your DAV Product under the TACP DAV Product Warranty

Exchange Program, contact TACP’s Consumer Solutions

Center toll free at 1-800-631-3811.

(2) You must include the original bill of sale (or a copy of the

original bill of sale) or other proof of purchase along with

the entire DAV Product when sending the DAV Product to

the TACP Warranty Exchange Center speciﬁed by TACP’s

Consumer Solutions Center. You are responsible for all

inbound transportation and insurance charges for the DAV

Product to the TACP Warranty Exchange Center.

Rental Units

The warranty for DAV Product rental units begins on the date

of the ﬁrst rental or thirty (30) days after the date of shipment

to the rental ﬁrm, whichever comes ﬁrst.

Commercial Units

DAV Products sold and used for commercial purposes have a

limited warranty for all parts and labor, which warranty begins

on the date of original retail purchase and ends on the date that

is ninety (90) days thereafter.

For additional information, visit TACP’s website:

www.tacp.toshiba.com

All WARRANTIES IMPlIED BY THE lAW OF ANY STATE

OF THE U.S.A., INClUDING THE IMPlIED WARRANTIES OF

MERCHANTABIlITY AND FITNESS FOR A PARTICUlAR

PURPOSE, ARE EXPRESSlY lIMITED TO THE DURATION OF

THE lIMITED WARRANTIES SET FORTH ABOVE. WITH THE

EXCEPTION OF ANY WARRANTIES IMPlIED BY THE lAW

OF ANY STATE OF THE U.S.A. AS HEREBY lIMITED, THE

FOREGOINGWARRANTY IS EXClUSIVE AND IN lIEU OF All

OTHER WARRANTIES, GUARANTEES, AGREEMENTS, AND

OF All OTHERWARRANTIES, GUARANTEES, AGREEMENTS,

AND OR REPlACEMENT OF ANY PARTS. IN NO EVENT SHAll

TACP BE lIABlE FOR CONSEQUENTIAl OR INCIDENTAl

DAMAGES (INClUDING, BUT NOT lIMITEDTO, lOST PROFITS,

BUSINESS INTERRUPTION, OR MODIFICATION OR ERASURE

OF RECORDED DATA CAUSED BY USE, MISUSE OR INABIlITY

TO USE THIS DAV PRODUCT).

Owner’s Manual and Product Registration Card

Read this owner’s manual thoroughly before operating this DAV

Product. Complete and mail the enclosed product registration

card or register your DAV Product on-line at www.tacp.toshiba.

com/service as soon as possible. By registering your DAV

Product you will enable TACP to bring you new products

speciﬁcally designed to meet your needs and help us to contact

you in the unlikely event a safety notiﬁcation is required under

the U.S. Consumer Product Safety Act. Failure to complete

and return the product registration card does not diminish your

warranty rights.

Your Responsibility

THE ABOVE WARRANTIES ARE SUBJECT TO FOLLOWING

CONDITIONS:

(1) You must retain your bill of sale or provide other proof of

purchase.

(2) All warranty servicing of this DAV Product must be made pursuant

to the TACP DAV Product Warranty Exchange Program.

(3) The warranties fromTACP are effective only if the DAV Product

is purchased and operated in the Continental U.S.A.or Puerto

Rico.

(4) Labor service charges for set installation, setup, adjustment

of customer controls, and installation or repair of antenna

systems are not covered by this warranty. Reception

problems caused by inadequate antenna systems are your

responsibility.

(5) Warranties extend only to defects in materials or workmanship

as limited above, and do not extend to any DAV Product or

parts that have been lost or discarded by you or to damage to

the DAV Product or parts caused by ﬁres, misuse, accident,

Acts of God ( such as lightning or ﬂuctuations in electric

power), improper installation, improper maintenance, or use in

violation of instructions furnished byTACP;use or malfunction

No person, agent, distributor, dealer, or company is authorized

to change, modify, or extend the terms of these warranties in any

manner whatsoever. The time within which an action must be

commenced to enforce any obligation of TACP arising under the

warranty or under any statute or law of the United States or any

state thereof is hereby limited to ninety (90) days from the date you

discover, or should have discovered, the defect.This limitation does

not apply to implied warranties arising under state law.

THIS WARRANTY GIVES YOU SPECIFIC lEGAl RIGHTS AND

YOU MAY AlSO HAVE OTHER RIGHTSWHICH MAYVARY FROM

STATE TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A.

DO NOT AllOW lIMITATIONS ON HOW lONG AN IMPlIED

WARRANTY lASTS, WHEN AN ACTION MAY BE BROUGHT,

OR THE EXClUSION OR lIMITATION OF INCIDENTAl OR

CONSEQUENTIAl DAMAGES, SO THE ABOVE PROVISIONS

MAY NOT APPlY TOYOU UNDER SUCH CIRCUMSTANCES.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Disclaimer

BDX2500 requires a wireless adapter - sold separately.

Up-conversion of DVD content will result in near HD picture quality. 1080p capable display required for viewing in 1080p. Feature

performance may vary and may also require an always-on broadband internet connection. Firmware update and additional

bandwidth may be required. BD-Live™ may require an SD or SDHC card with available storage capacity of at least 1GB.

Internet services available only in the United States. Third party internet services are not provided by Toshiba, may change

or be discontinued at any time and may be subject to third party restrictions. Toshiba makes no representations or warranties

about these services, which may require the creation of a user account through a computer with internet access. Third party

internet service users may incur one-time and/or recurring charges. For Dolby® TrueHD and DTS-HD Master Audio | Essential™

playback, content encoded in Dolby® TrueHD and DTS-HD Master Audio | Essential™ format required. Viewing 1080p/24 fps

output requires 1080p/24 fps encoded content and an HD display capable of accepting a 1080p/24Hz signal. Supported ﬁle

types: JPEG, MP3, WMA, and AVCHD. Some recordable media, cards or ﬁles may not be supported. Product speciﬁcations,

information and availability are all subject to change without notice.

license information on the software used in the TOSHIBA BD player

This document is statement purpose only. Not concerned with operation of this product.

The software pre-installed in the TOSHIBA BD player consists of multiple, independent software components. Each software

component is copyrighted by TOSHIBA or a third party.

The TOSHIBA BD player uses software components that are distributed as freeware under a third-party end-user license

agreement or copyright notice (hereinafter referred to as a “EULA”).

Some EULAs require that the source code of the applicable component be disclosed as the condition for distributing the software

component in executable format. You can check the software components subject to such EULA requirements on the following

phone number:

Phone number: 1-800-631-3811

TOSHIBA provides a warranty for the TOSHIBA BD player you have purchased under conditions set forth by TOSHIBA.

However, some of the software components distributed under an EULA are made available for use by the user on the assumption

that they are not copyrighted or warranted by TOSHIBA or any third party. These software components are licensed to the user

free of charge and therefore not covered by any warranty within the scope of the applicable laws. These software components

are not subject to any copyrights or other third-party rights and are provided in “as is” condition without any warranty, whether

express or implied. “Warranty” here includes, but not limited to, an implied warranty for marketability or ﬁtness for speciﬁc uses.

All risks associated with the quality or performance of these software components are assumed by the user. TOSHIBA shall not

be liable whatsoever for any cost of repair or correction or other incidental expense incurred in connection with a defect found in

any of these software components. Unless speciﬁed under the applicable laws or in a written agreement, a party who changes

or redistributes the software with consent from the copyright holders or based on the aforementioned licenses shall not be held

liable whatsoever for any loss arising from the use of or inability to use such software components.The same applies even when

the copyright holders or relevant third parties have been informed of the possibility of such loss. “Loss” here includes normal,

special, incidental and indirect loss (including, but not limited to, the loss of data or its accuracy; loss incurred by the user or any

third party; and interface incompatibility with other software). Please read each EULA for details on the use conditions and items

that must be observed regarding these software components.

The table below lists the software components pre-installed in the TOSHIBA BD player, which are subject to EULAs. The user

should read the applicable EULAs carefully before using these software components. The EULAs are exhibited in their original

text (English) as exactly written by the respective parties other than TOSHIBA.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Open-Source Third-party Software Included in the BD-Player (as of Feb 2010):

Software

license (*= source must be distributed on request)

A copy of the GPL2.0 license is provided in Appendix K

A copy of the LGPL2.1 license is provided in Appendix L

*backtrace

*directfb-extra

*cairo

GPL2 (Included in DVD 3.x [7630 systems] only)

GPL2

LGPL2

*directfb

*iconv

openssl

BSD-old dual license.

The terms and conditions which apply to this software are provided in Appendix H.

This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit

(http://www.openssl.org)

curl

The terms and conditions which apply to this software are provided in Appendix A.

*freetype

The terms and conditions which apply to this software are provided in Appendix G.

Recommended advertisement is:

jpeg

expat

mng

png

xml

The terms and conditions which apply to this software are provided in Appendix B.

The terms and conditions which apply to this software are provided in Appendix I.

The terms and conditions which apply to this software are provided in Appendix C.

The terms and conditions which apply to this software are provided in Appendix D.

The terms and conditions which apply to this software are provided in Appendix E.

The terms and conditions which apply to this software are provided in Appendix F.

zlib

Open-Source Third-party Software Included in the Kernel/Rootfs: (as of Feb 2010)

(*= source must be distributed on request)

A copy of the GPL license is provided in Appendix K

A copy of the LGPL license is provided in Appendix L

Utility

Base Version

license

GPL 2.0

*kernel

*arp

net-tools-1.52

GNU Bash-3.2

busybox-1.11.1

cramfs

*bash

*busybox

*cramfsck

*dhcpcd

*e2fsprogs

*fdisk

dhcpcd-1.3

e2fsprogs-1.41.5

fdisk-2.10m

TinyLogin-0.80

sysutils

*getty

*hostnamesysutils

*ifconﬁg

*iptables

*kill

net-tools-1.52

iptables-1.4.3

sysutils

*mkcramfs

cramfs

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

*mtd-utils

mtd-utils-20090511

ntfs-3g 2009.4.4

TinyLogin-0.80

sysutils

GPL 2.0

zlib license

*ntfs-3g

*passwd

*ps

*route

net-tools-1.52

sfdisk-3.07

*sfdisk

*shutdown

*tinylogin

*hotplug

sysutils

TinyLogin-0.80

hotplug-1.8

*utelnetd

*procps

utelnetd-0.1.3

procps-3.2.8

freetype-2.1.2

GNU Bash-2.05

GNU termcap 1.3

zlib-1.2.3

*libfreetype.so.6.3.

*libtermcap.so

*libtermcap.so.2.0.8

zlib

The terms and conditions which apply to this software are provided in Appendix F.

libusb.so

uClibc

libusb-0.1.12

LGPL 2.1

BSD-new

uClibc-nptl-0.9.29-20070423

tcpdump-4.0.0

tcpdump

The terms and conditions which apply to this software are provided in Appendix M.

strace

strace 4.5.18

BSD-new

BSD-old

The terms and conditions which apply to this software are provided in Appendix M.

hdparm

hdparm-6.9

The terms and conditions which apply to this software are provided in Appendix M.

libpcap

libcap-1.0.0

The terms and conditions which apply to this software are provided in Appendix M.

portmap

The terms and conditions which apply to this software are provided in Appendix J.

Advertising sentence is:

openssl 0.9.8k BSD-old. See advertisement notice above.

openssl

luxi Font Copyright

a registered trademark of Bigelow & Holmes Inc. Permission is hereby granted, free of charge, to any person obtaining a copy of these Fonts and

associated documentation ﬁles (the “Font Software”), to deal in the Font Software, including without limitation the rights to use, copy, merge,

publish, distribute, sublicense, and/or sell copies of the Font Software, and to permit persons to whom the Font Software is furnished to do so,

subject to the following conditions:

The above copyright and trademark notices and this permission notice shall be included in all copies of one or more of the Font Software.

The Font Software may not be modiﬁed, altered, or added to, and in particular the designs of glyphs or characters in the Fonts may not be modiﬁed

nor may additional glyphs or characters be added to the Fonts. This License becomes null and void when the Fonts or Font Software have been

modiﬁed.

THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED

TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT,

PATENT, TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL BIGELOW & HOLMES INC. OR URW++ GMBH. BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT

SOFTWARE OR FROM OTHER DEALINGS IN THE FONT SOFTWARE.

Except as contained in this notice, the names of Bigelow & Holmes Inc. and URW++ GmbH. shall not be used in advertising or otherwise to promote

the sale, use or other dealings in this Font Software without prior written authorization from Bigelow & Holmes Inc. and URW++ GmbH.

For further information, contact:

[email protected] or [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Appendix A - CURl license

Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright

notice and this permission notice appear in all copies.

THE SOFTWARE IS PROVIDED „AS IS“, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED

TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY

RIGHTS. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,

WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE

OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other

dealings in this Software without prior written authorization of the copyright holder.

Appendix B - JPEG license

LEGAL ISSUES

============

In plain English:

1. We don’t promise that this software works. (But if you ﬁnd any bugs, please let us know!)

2. You can use this software for whatever you want. You don’t have to pay us.

3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that

you’ve used the IJG code.

In legalese:

The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy,

merchantability, or ﬁtness for a particular purpose. This software is provided “AS IS”, and you, its user, assume the entire risk as to its quality

and accuracy.

Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for any purpose, without fee, subject to these

conditions:

(1) If any part of the source code for this software is distributed, then this README ﬁle must be included, with this copyright and no-warranty

notice unaltered; and any additions, deletions, or changes to the original ﬁles must be clearly indicated in accompanying documentation.

(2) If only executable code is distributed, then the accompanying documentation must state that “this software is based in part on the work of the

Independent JPEG Group”.

(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept

NO LIABILITY for damages of any kind.

These conditions apply to any software derived from or based on the IJG code, not just to the unmodiﬁed library. If you use our work, you ought

to acknowledge us.

Permission is NOT granted for the use of any IJG author’s name or company name in advertising or publicity relating to this software or products

derived from it. This software may be referred to only as “the Independent JPEG Group’s software”.

We speciﬁcally permit and encourage the use of this software as the basis of commercial products, provided that all warranty or liability claims

are assumed by the product vendor.

Appendix C - MNG license

/* **************************************************************************************************************************************************

[You may insert additional notices after this sentence if you modify this source]

For the purposes of this copyright and license, “Contributing Authors” is deﬁned as the following set of individuals:

Gerard Juyn

The MNG Library is supplied “AS IS”. The Contributing Authors disclaim all warranties, expressed or implied, including, without limitation, the

warranties of merchantability and of ﬁtness for any purpose. The Contributing Authors assume no liability for direct, indirect, incidental, special,

exemplary, or consequential damages, which may result from the use of the MNG Library, even if advised of the possibility of such damage.

Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the

following restrictions:

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

1. The origin of this source code must not be misrepresented; you must not claim that you wrote the original software.

2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source.

3. This Copyright notice may not be removed or altered from any source or altered source distribution.

The Contributing Authors speciﬁcally permit, without fee, and encourage the use of this source code as a component to supporting the MNG and

JNG ﬁle format in commercial products. If you use this source code in a product, acknowledgment would be highly appreciated.

Parts of this software have been adapted from the libpng package. Although this library supports all features from the PNG speciﬁcation (as MNG

descends from it) it does not require the libpng package. It does require the zlib library and optionally the IJG jpeg library, and/or the “little-cms”

library by Marti Maria (depending on the inclusion of support for JNG and Full-Color-Management respectively.

This library’s function is primarily to read and display MNG animations. It is not meant as a full-featured image-editing component! It does however

offer creation and editing functionality at the chunk level. (future modiﬁcations may include some more support for creation and or editing)

Appendix D - PNG license File Distribution Clause

The Contributing Authors and Group 42, Inc. speciﬁcally permit, without fee, and encourage the use of this source code as a component to

supporting the PNG ﬁle format in commercial products. If you use this source code in a product, acknowledgment is not required but would be

appreciated.

Appendix E – XMl license

Except where otherwise noted in the source code (e.g. the ﬁles hash.c, list.c and the trio ﬁles, which are covered by a similar licence but with

different Copyright notices) all the ﬁles are:

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation ﬁles (the “Software”),

to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or

sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO

THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL

THE DANIEL VEILLARD BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT

OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE

SOFTWARE.

Except as contained in this notice, the name of Daniel Veillard shall not be used in advertising or otherwise to promote the sale, use or other

dealings in this Software without prior written authorization from him.

Appendix F – zlib Distribution Conditions

This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held liable for any damages arising from

the use of this software.

Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely,

subject to the following restrictions:

1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a

product, an acknowledgment in the product documentation would be appreciated but is not required.

2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.

3. This notice may not be removed or altered from any source distribution.

Jean-loup Gailly

[email protected]

Mark Adler

[email protected]

If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to sign. The sources are provided for free but

without warranty of any kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not include third-party code.

If you redistribute modiﬁed sources, we would appreciate that you include in the ﬁle ChangeLog history information documenting your changes.

Please read the FAQ for more information on the distribution of modiﬁed source versions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Appendix G – Freetype license

The FreeType Project LICENSE

----------------------------

2006-Jan-27

David Turner, Robert Wilhelm, and Werner Lemberg

Introduction

============

The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine, various tools

and contributions which rely on, or relate to, the FreeType Project.

This license applies to all ﬁles found in such packages, and which do not fall under their own explicit license. The license affects thus the

FreeType font engine, the test programs, documentation and makeﬁles, at the very least.

This license was inspired by the BSD, Artistic, and IJG (Independent JPEG Group) licenses, which all encourage inclusion and use of

free software in commercial and freeware products alike. As a consequence, its main points are that:

We don’t promise that this software works. However, we will be interested in any kind of bug reports. (`as is’ distribution)

You can use this software for whatever you want, in parts or full form, without having to pay us. (`royalty-free’ usage)

You may not pretend that you wrote this software. If you use it, or only parts of it, in a program, you must acknowledge somewhere in your

documentation that you have used the FreeType code. (`credits’)

We speciﬁcally permit and encourage the inclusion of this software, with or without modiﬁcations, in commercial products. We disclaim all

warranties covering The FreeType Project and assume no liability related to The FreeType Project.

Finally, many people asked us for a preferred form for a credit/disclaimer to use in compliance with this license. We thus encourage you to

use the following text:

“””

Please replace <year> with the value from the FreeType version you actually use.

Legal Terms

===========

0. Deﬁnitions

--------------

Throughout this license, the terms `package’, `FreeType Project’, and `FreeType archive’ refer to the set of ﬁles originally distributed by the

authors (David Turner, Robert Wilhelm, and Werner Lemberg) as the `FreeType Project’, be they named as alpha, beta or ﬁnal release.

`You’ refers to the licensee, or person using the project, where `using’ is a generic term including compiling the project’s source code as well as

linking it to form a `program’ or `executable’. This program is referred to as `a program using the FreeType engine’.

This license applies to all ﬁles distributed in the original FreeType Project, including all source code, binaries and documentation, unless

otherwise stated in the ﬁle in its original, unmodiﬁed form as distributed in the original archive. If you are unsure whether or not a particular

ﬁle is covered by this license, you must contact us to verify this.

below.

1. No Warranty

--------------

THE FREETYPE PROJECT IS PROVIDED `AS IS’WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT

NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL ANY OF

THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY THE USE OR THE INABILITY TO USE, OF THE

FREETYPE PROJECT.

2. Redistribution

-----------------

This license grants a worldwide, royalty-free, perpetual and irrevocable right and license to use, execute, perform, compile, display, copy,

create derivative works of, distribute and sublicense the FreeType Project (in both source and object code forms) and derivative works thereof

for any purpose; and to authorize others to exercise some or all of the rights granted herein, subject to the following conditions:

Redistribution of source code must retain this license ﬁle (`FTL.TXT’) unaltered; any additions, deletions or changes to the original ﬁles must

be clearly indicated in accompanying documentation. The copyright notices of the unaltered, original ﬁles must be preserved in all copies

of source ﬁles.

Redistribution in binary form must provide a disclaimer that states that the software is based in part of the work of the FreeType Team, in

the distribution documentation. We also encourage you to put an URL to the FreeType web page in your documentation, though this isn’t

mandatory.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

These conditions apply to any software derived from or based on the FreeType Project, not just the unmodiﬁed ﬁles. If you use our work, you

must acknowledge us. However, no fee need be paid to us.

3. Advertising

--------------

Neither the FreeType authors and contributors nor you shall use the name of the other for commercial, advertising, or promotional purposes

without speciﬁc prior written permission.

We suggest, but do not require, that you use one or more of the following phrases to refer to this software in your documentation or advertising

materials: `FreeType Project’, `FreeType Engine’, `FreeType library’, or `FreeType Distribution’.

As you have not signed this license, you are not required to accept it. However, as the FreeType Project is copyrighted material, only this

license, or another one contracted with the authors, grants you the right to use, distribute, and modify it. Therefore, by using, distributing, or

modifying the FreeType Project, you indicate that you understand and accept all the terms of this license.

4. Contacts

-----------

There are two mailing lists related to FreeType:

o [email protected]

Discusses general use and applications of FreeType, as well as future and wanted additions to the library and distribution.

If you are looking for support, start in this list if you haven’t found anything to help you in the documentation.

o [email protected]

Discusses bugs, as well as engine internals, design issues, speciﬁc licenses, porting, etc.

Our home page can be found at

http://www.freetype.org

--- end of FTL.TXT ---

Appendix H – Openssl license

LICENSE ISSUES

==============

The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the

toolkit.

See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to

OpenSSL, please contact [email protected].

OpenSSL License

---------------

/* ====================================================================

Redistribution and use in source and binary forms, with or without modiﬁcation, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation

and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgment:“This product includes software

developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”

4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without

prior written permission. For written permission, please contact [email protected].

5. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission *

of the OpenSSL Project.

6. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by the OpenSSL

Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS’’ AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.

IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,

WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE

USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

This product includes cryptographic software written by Eric Young ([email protected]). This product includes software written by Tim Hudson

([email protected]).

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Original SSLeay License

-----------------------

This package is an SSL implementation written by Eric Young ([email protected]). The implementation was written so as to conform with

Netscapes SSL.

This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to

all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this

distribution is covered by the same copyright terms except that the holder is Tim Hudson ([email protected]).

Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric

Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or

in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modiﬁcation, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation

and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product includes

cryptographic software written by Eric Young ([email protected])”

The word ‘cryptographic’ can be left out if the rouines from the library being used are not cryptographic related :-).

4. IfyouincludeanyWindowsspeciﬁccode(oraderivativethereof)fromtheappsdirectory(applicationcode)youmustincludeanacknowledgement:

“This product includes software written by Tim Hudson ([email protected])”

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN

NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,

OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS

OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be

copied and put under another distribution licence [including the GNU Public Licence.]

Appendix I – Expat license

maintainers.

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation ﬁles (the “Software”),

to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or

sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO

THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL

THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION

OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER

DEALINGS IN THE SOFTWARE.

Appendix J – Portmap license

/*-

Redistribution and use in source and binary forms, with or without modiﬁcation, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation

and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes

software developed by the University of California, Berkeley and its contributors.

4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software

without speciﬁc prior written permission.

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS

OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT

OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Appendix K – GNU GPl 2.0

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is

intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public

License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free

Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the

freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that

you can change the software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These

restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have.You must

make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute

and/or modify the software.

Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the

software is modiﬁed by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems

introduced by others will not reﬂect on the original authors’ reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will

individually obtain patent licenses, in effect making the program proprietary.To prevent this, we have made it clear that any patent must be licensed

for everyone’s free use or not licensed at all.

The precise terms and conditions for copying, distribution and modiﬁcation follow.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under

the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means

either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or

with modiﬁcations and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modiﬁcation”.) Each

licensee is addressed as “you”.

Activities other than copying, distribution and modiﬁcation are not covered by this License; they are outside its scope. The act of running the

Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of

having been made by running the Program). Whether that is true depends on what the Program does.

1.You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and

appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License

and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2.You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such

modiﬁcations or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a) You must cause the modiﬁed ﬁles to carry prominent notices stating that you changed the ﬁles and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be

licensed as a whole at no charge to all third parties under the terms of this License.

c) If the modiﬁed program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the

most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else,

saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of

this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is

not required to print an announcement.)

These requirements apply to the modiﬁed work as a whole. If identiﬁable sections of that work are not derived from the Program, and can be

reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when

you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the

distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each

and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right

to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of

a storage or distribution medium does not bring the other work under the scope of this License.

3.You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections

1 and 2 above provided that you also do one of the following:

a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2

above on a medium customarily used for software interchange; or,

b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing

source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2

above on a medium customarily used for software interchange; or,

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for

noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection

b above.)

The source code for a work means the preferred form of the work for making modiﬁcations to it. For an executable work, complete source code

means all the source code for all modules it contains, plus any associated interface deﬁnition ﬁles, plus the scripts used to control compilation and

installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed

(in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs,

unless that component itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the

source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along

with the object code.

4.You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy,

modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have

received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5.You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the

Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the

Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying,

distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original

licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the

recipients’ exercise of the rights granted herein.You are not responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions

are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from

the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent

obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free

redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this

License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and

the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this

section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices.

Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application

of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot

impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright

holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that

distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body

of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will

be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program speciﬁes a version number of this License which applies to it and “any later

version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software

Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software

Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask

for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make

exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting

the sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT

PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER

PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK

AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITHYOU. SHOULD THE PROGRAM PROVE DEFECTIVE,YOU ASSUME

THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY

OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,

INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE

THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED

BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER

OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Appendix l – GNU lGPl 2.1

GNU LESSER GENERAL PUBLIC LICENSE

Version 2.1, February 1999

59 Temple Place, Suite 330, Boston, MA 02111-1307 USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the ﬁrst released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the

version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are

intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software

Foundation and other authors who decide to use it. You can use it too, but we suggest you ﬁrst think carefully about whether this license or the

ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you

have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want

it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These

restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You

must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object ﬁles to

the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these

terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to

copy, distribute and/or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modiﬁed by someone

else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be

affected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively

restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for

a version of the library must be consistent with the full freedom of use speciﬁed in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General

Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for

certain libraries in order to permit linking those libraries into non-free programs.

When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work,

a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination ﬁts its criteria

of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.

We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public

License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are

the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special

circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-

facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job

as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General

Public License.

In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software.

For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as

well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with

the Library has the freedom and the wherewithal to run that program using a modiﬁed version of the Library.

The precise terms and conditions for copying, distribution and modiﬁcation follow. Pay close attention to the difference between a “work based

on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the

library in order to run.

GNU LESSER GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other

authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”). Each licensee is

addressed as “you”.

A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some

of those functions and data) to form executables.

The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library”

means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim

or with modiﬁcations and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term

“modiﬁcation”.)

“Source code” for a work means the preferred form of the work for making modiﬁcations to it. For a library, complete source code means all the

source code for all modules it contains, plus any associated interface deﬁnition ﬁles, plus the scripts used to control compilation and installation

of the library.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Activities other than copying, distribution and modiﬁcation are not covered by this License; they are outside its scope. The act of running a

program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library

(independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that

uses the Library does.

1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you

conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that

refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such

modiﬁcations or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a) The modiﬁed work must itself be a software library.

b) You must cause the ﬁles modiﬁed to carry prominent notices stating that you changed the ﬁles and the date of any change.

c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.

d) If a facility in the modiﬁed Library refers to a function or a table of data to be supplied by an application program that uses the facility, other

than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application

does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely well-deﬁned independent of the application. Therefore,

Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it,

the square root function must still compute square roots.)

These requirements apply to the modiﬁed work as a whole. If identiﬁable sections of that work are not derived from the Library, and can be

reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when

you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the

distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each

and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right

to control the distribution of derivative or collective works based on the Library.

In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a

storage or distribution medium does not bring the other work under the scope of this License.

3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this,

you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this

License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead

if you wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent

copies and derivative works made from that copy.

This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of

Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed

under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.

If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code

from the same place satisﬁes the requirement to distribute the source code, even though third parties are not compelled to copy the source along

with the object code.

5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it,

is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of

this License.

However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions

of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution

of such executables.

When a “work that uses the Library” uses material from a header ﬁle that is part of the Library, the object code for the work may be a derivative

work of the Library even though the source code is not.

Whether this is true is especially signiﬁcant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be

true is not precisely deﬁned by law.

If such an object ﬁle uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines

or less in length), then the use of the object ﬁle is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this

object code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables

containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce a work containing

portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modiﬁcation of the work for the

customer’s own use and reverse engineering for debugging such modiﬁcations.

You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License.

You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library

among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things:

a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were

used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the

complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then

relink to produce a modiﬁed executable containing the modiﬁed Library. (It is understood that the user who changes the contents of deﬁnitions

ﬁles in the Library will not necessarily be able to recompile the application to use the modiﬁed deﬁnitions.)

b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library

already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a

modiﬁed version of the library, if the user installs one, as long as the modiﬁed version is interface-compatible with the version that the work

was made with.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials speciﬁed in Subsection 6a, above,

for a charge no more than the cost of performing this distribution.

d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above speciﬁed

materials from the same place.

e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.

For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for reproducing the

executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either

source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that

component itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating

system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7.You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered

by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other

library facilities is otherwise permitted, and provided that you do these two things:

a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must

be distributed under the terms of the Sections above.

b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to ﬁnd the

accompanying uncombined form of the same work.

8.You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise

to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However,

parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in

full compliance.

9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute

the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing

the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying,

distributing or modifying the Library or works based on it.

10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original

licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the

recipients’ exercise of the rights granted herein.You are not responsible for enforcing compliance by third parties with this License.

11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions

are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from

the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent

obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free

redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this

License would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and

the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this

section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices.

Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application

of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot

impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright

holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that

distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the

body of this License.

13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new

versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Library speciﬁes a version number of this License which applies to it and “any

later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free

Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software

Foundation.

14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the

author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we

sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software

and of promoting the sharing and reuse of software generally.

NO WARRANTY

15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED

BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE

THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY

AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL

NECESSARY SERVICING, REPAIR OR CORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY

OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,

INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE

THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED

BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR

OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

How to Apply These Terms to Your New Libraries

If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone

can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General

Public License).

To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source ﬁle to most effectively convey

the exclusion of warranty; and each ﬁle should have at least the “copyright” line and a pointer to where the full notice is found.

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by

the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.

Thislibraryisdistributedinthehopethatitwillbeuseful, butWITHOUTANYWARRANTY;withouteventheimpliedwarrantyofMERCHANTABILITY

or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.

You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation,

Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA

Also add information on how to contact you by electronic and paper mail.You should also get your employer (if you work as a programmer) or your

school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob’ (a library for tweaking knobs) written by James Random Hacker.

<signature of Ty Coon>, 1 April 1990

Ty Coon, President of Vice

That’s all there is to it!

Appendix M – BSD-New

Redistribution and use in source and binary forms, with or without modiﬁcation, are permitted provided that: (1) source code distributions retain

the above copyright notice and this paragraph in its entirety, (2) distributions including binary code include the above copyright notice and this

paragraph in its entirety in the documentation or other materials provided with the distribution, and (3) all advertising materials mentioning features

or use of this software display the following acknowledgement:

``This product includes software developed by the University of California, Lawrence Berkeley Laboratory and its contributors.’’ Neither the name

of the University nor the names of its contributors may be used to endorse or promote products derived from this software without speciﬁc prior

written permission.

THIS SOFTWARE IS PROVIDED ``AS IS’’ AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION,

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Appendix N – CinemaNow

Third Party Requirements

a. gSOAP.

The following notice is applicable to the CinemaNow SDK. Company is required to include such notice in the documentation for any Embedded

Products it distributes.

Part of the software embedded in this product is gSOAP software.

THE SOFTWARE IN THIS PRODUCT WAS IN PART PROVIDED BY GENIVIA INC AND ANY EXPRESS OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,

OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS

OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

b. [THE CODE IS BEING PROVIDED IN OBJECT CODE SO THE ABOVE DOESN’T APPlY]

c. Curl/ 7.12.2

Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright

notice and this permission notice appear in all copies.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED

TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY

RIGHTS. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,

WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE

OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other

dealings in this Software without prior written authorization of the copyright holder.

d. C-ARES 1.6.0

Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that

the above copyright notice appear in all copies and that both that copyright notice and this permission notice appear in supporting documentation,

and that the name of M.I.T. not be used in advertising or publicity pertaining to distribution of the software without speciﬁc, written prior permission.

M.I.T. makes no representations about the suitability of this software for any purpose. It is provided “as is” without express or implied warranty.

e. Openssl 0.9.5a

Original SSLeay License

-----------------------

This package is an SSL implementation written by Eric Young ([email protected]). The implementation was written so as to conform with

Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are adhered to. The following

conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation

included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson ([email protected]).

Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric

Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or

in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modiﬁcation, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation

and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product includes

cryptographic software written by Eric Young ([email protected])” The word ‘cryptographic’ can be left out if the rouines from the library being

used are not cryptographic related :-).

4.If you include anyWindows speciﬁc code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: