MODEL SF-475
Fabric Steamer
by Top Innovations, Inc.
Please read all instructions before use.
Mail in your warranty registration card.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
WARNING: To reduce the risk of fire, electrical shock, or injury,
the following basic safety precautions should always be followed
when using an electrical appliance.
READ ALL INSTRUCTIONS BEFORE USING YOUR FABRIC STEAMER
1. Unit Water Reservoir is designed to hold a maximum of 48 oz. (1420 ml.) of
water. Use caution when filling, to avoid burns from spilling water, or possible
electrical shock.
2. DO NOT leave your SF-475 Fabric Steamer unattended when plugged in or not
in use. Use only for its intended purpose as indicated in this manual.
3.
This unit is not a toy. Close supervision is required when using unit
near children, pets, and plants. Steam produced by unit is hot and
pressurized. Care must be taken to avoid burns or other injuries. Never
point nozzle at people or pets.
4. To reduce the risk of contact with hot water emitting from steam vents, hold
appliance away from body and check for signs of condensation or leakage.
5. DO NOT use this unit if electrical cord or outlet is damaged. DO NOT use unit if
it is not working properly or has been dropped, damaged or left outdoors. If such
damage occurs, DO NOT disassemble or attempt repairs, take unit to a qualified
service person for examination and repair. Incorrect reassembly or repair could
cause a risk of fire, electrical shock, or injury to persons when steamer is used.
6. To reduce risk of electrical shock, DO NOT immerse in water or other liquids.
DO NOT use electrical cord or Hose as a handle. DO NOT allow cord or Hose to
be crimped by closing it in doors. DO NOT pull or stretch cord or Hose around
sharp corners or edges.
7. Before filling unit with water, always unplug power cord from electrical outlet.
Failure to do so may result in electrical shock and injury.
8. Do not allow electrical cord to touch hot surfaces. Let appliance cool completely
before putting away. Loop cord loosely around appliance when storing.
9. DO NOT use this unit with extension cords or electrical outlets that have
inadequate current capacity. A three-prong outlet or a properly grounded adapter
is necessary when using SF-475 Fabric Steamer.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY
3
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
WARNING: To reduce the risk of electrical shock, this appliance
has a three-pronged plug. This plug will fit in a polarized wall
outlet only one way. If the plug does not fit fully in the outlet,
contact a licensed electrician to install a proper outlet. DO NOT
attempt to modify the plug or defeat this safety feature.
10. In order to unplug SF-475 Fabric Steamer, grasp plug and pull smoothly and
firmly from outlet. DO NOT attempt to unplug unit by pulling or tugging on
cord.
11. Always keep Steam Nozzle elevated above Water Reservoir. DO NOT lay Hose
on floor.
12. Use caution, as burns could occur from touching hot metal parts, hot water or
steam.
13. SF-475 Fabric Steamer is only meant to be used with recommended SF-475
accessories. Other types of attachments are not to be used with Fabric Steamer.
Doing so may cause injuries or damage to unit.
14. Nozzle and attachments become hot during use. To avoid injuries, DO NOT
touch nozzle while using this appliance. DO NOT attempt to change
attachments while unit is emitting steam.
15. When filling your Fabric Steamer, only water should be used in unit. Other
cleaning agents will damage unit and can cause injuries.
16. DO NOT operate unit if steam opening is blocked. Should this occur,
immediately cease usage and unplug from electrical outlet.
17. Store your SF-475 Fabric Steamer in a cool, dry place.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY
4
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
FABRIC STEAMER PRODUCT INFORMATION
The following features and accessories are included with your Steam Cleaner. Carefully
inspect packaging material as some parts are shipped inside Styrofoam packaging. To obtain
possible missing parts, refer to the Customer Support section on page 13 of this manual.
UNIT FEATURES
& ACCESSORIES
1. Pole Top
1a. Steam Nozzle Holder
1b. Clothes Hanger Hook
2. Steam Nozzle
3. Handle
4. Telescopic Pole
4a. Pole Base
5. Hose
5a. Hose Base
6. Steam Ready Light
7. Lighted On/Off Switch
8. Water Reservoir
9. Storage Compartment
9a. Water Reservoir Cap
9b. Compartment Lid
10. Lint Remover
11. Fabric Brush
12. Cloth Cover
13. Measuring Cup
14. Water Funnel
15. Press Pad
5
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
FABRIC STEAMER PRODUCT INFORMATION
• The Pole Top (1) is comprised of the Steam Nozzle Holder (1a) and the Clothes
Hanger Hook (1b). The Steam Nozzle Holder provides a safe and convenient place
to hang the Steam Nozzle. The Clothes Hanger Hook allows you to steam
garments that are hanging from a clean, rust-free hanger.
• The Steam Nozzle (2) is designed to spread hot, penetrating steam over a wide
area.
• The Handle (3) is designed to stay relatively cool while providing the optimum
amount of safety and user comfort.
• The Telescopic Pole (4) connects the Pole Top to the steamer and collapses to
allow quick, compact storage of the unit. The Pole Base (4a) is the mount where
the Telescopic Pole connects to the main unit body.
• The Hose (5) safely channels steam from the boiler to the Steam Nozzle. The Hose
Base (5a) is the mount where the Hose connects to the main unit body.
• The Steam Ready Light (6) indicates when the unit is ready to steam, by lighting
up during heating and turning off when the steam is ready.
• The Lighted On/Off Switch (7) turns the unit on and off, and provides a clear
visual indication when the steamer is turned on.
• The Water Reservoir (8) is where water is stored for use by the unit. There must
be a sufficient amount of water (16-48 oz.) in the Water Reservoir in order for the
unit to properly function.
• The Storage Compartment (9) provides a convenient place to store small
accessories. The Water Reservoir Cap (9a) is located inside the Storage
Compartment, and must be removed in order to expose the fill hole and fill the
Water Reservoir with water. The Compartment Lid (9b) is a hinged lid that covers
the Storage Compartment and Water Reservoir Cap.
• The Lint Remover (10) connects to the Steam Nozzle and is designed to assist in
removing lint, loose threads and other small particles from fabric.
• The Fabric Brush (11) connects to the Steam Nozzle and is designed to assist in
smoothing out exceptionally stubborn wrinkles.
• The Cloth Cover (12) is connects to the Steam Nozzle, and is useful for preventing
large water droplets from dripping on delicate materials.
• The Measuring Cup (13) and Water Funnel (14) are provided to assist you in
easily and consistently filling the Water Reservoir with the optimum amount of
water (16-48 oz. / 473-1420 ml.).
• The Press Pad (15) fits on your hand, allowing you to support the fabric for a
more thorough steaming. The Press Pad also protects your hand from being
burned by hot steam.
6
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLING THE FABRIC STEAMER
ATTACHING THE TELESCOPIC POLE
1. Attach Pole Top by sliding it onto top of Telescopic Pole as shown (FIGURE 1).
Note that Pole Top must align correctly in two grooves that run the length of pole.
2. Line up grooves of Telescopic Pole with two tabs inside Pole Base hole, and
insert bottom section of Pole into Base (FIGURE 2).
3. Tighten knob by turning it in a clockwise direction until it is tight, and Telescopic
Pole sits firmly in place in the Pole Base (FIGURE 3).
FIGURE 2
FIGURE 1
FIGURE 3
EXTENDING TELESCOPIC POLE
1. Locate bottom extension lock, and swing
hinge outward as shown (FIGURE 4).
Extend middle section of Telescopic Pole as
far upward as it will go, then close hinge to
relock bottom extension lock.
2. Repeat Step 1 for remaining two extension
locks, until Telescopic Pole is extended to
it’s full height.
NOTE: It is recommended to extend
Telescopic Pole to it’s full height during
steamer operation. This ensures full
extension of Steam Hose for maximum flow
of steam.
FIGURE 4
7
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLING THE FABRIC STEAMER
CONNECTING HOSE
1. Slide Hose fitting onto threaded Hose Base (FIGURE 5)
2. Turn Hose fitting clockwise to secure it to Hose Base (FIGURE 6).
NOTE: Hand-tighten Hose fitting only. Do not over-tighten.
3. Hang Steam Nozzle on specially designed Steam Nozzle Holder as shown
(FIGURE 7).
CAUTION: To prevent steam from causing bodily injury or damage to
surfaces, always hang Steam Nozzle on Steam Nozzle Holder when not in use.
Do not lay Hose on floor as condensation may build up inside, causing
unwanted water droplets in steam.
CAUTION: Pulling on Hose with excessive force may damage it, resulting in a
steam leak.
FIGURE 6
FIGURE 5
FIGURE 7
ATTACHING LINT REMOVER /
FABRIC BRUSH / CLOTH COVER
1. Make sure Lighted On/Off Switch is set to “Off”
position, and that unit is not emitting any steam.
Do not try to connect Lint Remover, Fabric
Brush or Cloth Cover while unit is emitting
steam, as this can cause burns and injury.
2. Align two pegs on back of accessory with
corresponding holes on face of Steam Nozzle.
Use care to properly align attachment as shown
(FIGURE 8), so as not to cover up steam holes
on nozzle face.
FIGURE 8
3. Press accessory firmly onto Steam Nozzle, until
it fits securely in place.
8
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE FABRIC STEAMER
FILLING WATER RESERVOIR WITH WATER
1. Place Fabric Steamer on a flat, level surface.
2. Make sure Lighted On/Off Switch is set to “Off” position and grounded power
cord is unplugged from electrical outlet.
3. Flip up Compartment Lid. Cautiously unscrew and remove Water Reservoir Cap.
4. Water Reservoir should always be emptied after each use. If it was not emptied
after the last use, empty it now. This will prevent over-filling.
5. Fill Measuring Cup to maximum fill line (16 oz. / 473 ml.) with water.
NOTE: To prolong the life of your Fabric Steamer, we recommend using
distilled or de-mineralized water.
6. Using Water Funnel, carefully pour water from Measuring Cup into Water
Reservoir through fill hole.
WARNING: Extreme caution should be used when pouring water into the
Water Reservoir. Do not look directly down into fill hole when filling. Keep
your free hand and any children or pets at a safe distance.
7. Depending on how long you intend to steam, you may repeat steps 5 & 6 up to
two more times, to a maximum of 48 oz. (1420 ml.) of water. See chart below
for a comparison of the amount of water vs. approximate steam time.
8. Replace Water Reservoir cap, ensuring that it is screwed on tightly to prevent hot
steam from escaping and causing injury.
9. Lower Compartment Lid back down.
IMPORTANT: When steamer is first activated, it is natural for it to spray
small amounts of water. This is due to condensation forming in the Hose, and
will dissipate within 30 seconds of use. To help clear condensation out of Hose
more quickly, try the following:
• Point Steam Nozzle towards ground, sink or tub and shake it to force water
out of Hose.
• Extend Hose vertically as far as possible to allow water to drain back into
Water Reservoir.
9
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE FABRIC STEAMER
OPERATING THE FABRIC STEAMER
NOTE: Be sure that any desired attachments are
connected and Water Reservoir is filled before following
these steps.
1. Plug grounded power cord into a convenient 3-prong
electrical outlet.
2. Switch Lighted On/Off Switch to “On” position.
3. Steam Ready Light will illuminate while boiler is
heating. When Steam Ready Light deactivates (2-8
minutes, depending on amount of water in Water
Reservoir) unit will automatically begin emitting steam.
4. Place garment on a clean, rust-free clothes hanger.
5. Place hanger (with garment) on Clothes Hanger Hook
(FIGURE 10).
FIGURE 10
CAUTION: Use care when handling garments on the
Clothes Hanger Hook. Pulling on the garment with
too much force may cause the unit to tip over.
6. Direct Steam Nozzle towards bottom of garment. Steam
will rise along inside and outside of fabric, removing
wrinkles. Slowly slide Steam Nozzle vertically, from
bottom to top of garment (FIGURE 11).
NOTE: Do not allow kinks to form in hose at any
time during use.
7. Direct Steam Nozzle away from garment and smooth
fabric with your free hand.
8. Repeat steps 6 & 7 as necessary until fabric is smooth
and wrinkle free.
OTHER STEAMING TIPS
FIGURE 11
• Curtains and draperies may be steamed while still hanging.
• To remove wrinkles from towels, handkerchiefs and napkins, drape them over a rod or
towel rack and gently steam them.
• Heavier fabrics may require repeated steaming to effectively remove wrinkles.
• To remove exceptionally stubborn wrinkles steam both sides of fabric.
• For additional assistance in removing tough wrinkles, or to remove lint and other particles,
attach Fabric Brush or Lint Remover to Steam Nozzle (see Attaching Lint Remover and
Fabric Brush section on page 8 of this manual).
• Use Press Pad in order to steam difficult spots and edges and to create creases in fabric.
Slide your hand through the velcro strap on back of Press Pad to secure it to your hand.
This will protect your hand from the flow of hot steam. Then steam fabric while pressing it
firmly but gently against the Press Pad.
9. When you have completed your steaming tasks, immediately switch Lighted On/Off
Switch to “Off” position and unplug power cord from electrical outlet. Refer to Proper
Storage section on page 11 of this manual for information on proper cleaning and storage
of Fabric Steamer.
10
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & STORAGE GUIDELINES
PROPER STORAGE
Preparing your Fabric Steamer for storage is quick and simple. When you have fin-
ished your steaming tasks, follow the steps listed below.
1. Unplug grounded power cord from electrical outlet.
2. Allow unit to cool completely (at least 30 minutes).
3. Remove all attachments from unit.
4. Drain any remaining water in Water Reservoir into a sink or tub to prevent
over-filling during your next use.
5. Unhook three extension locks on Telescopic Pole, and press down on Pole Top
to collapse Pole into compact storage position. Re-lock extension locks.
6. Wrap Hose loosely around Telescopic Pole one time, and hang Steam Nozzle
from Steam Nozzle Holder.
7. Store all attachments safely away, preferably inside Storage Compartment or near
Fabric Steamer.
8. Store Fabric Steamer in a cool, dry location.
REMOVING MINERAL BUILD-UP
A common problem with steam appliances is mineral build-up caused by high
mineral content in many municipal water supplies. The best way to avoid this is
to use de-mineralized or distilled water in unit. If you are unable to use de-
mineralized or distilled water, we recommend you use this procedure monthly to
help avoid mineral build-up:
1. Switch Lighted On/Off Switch to “Off” position and unplug grounded power
cord from electrical outlet. Allow unit to completely cool.
2. Remove all accessories from unit.
3. Flip up Compartment Lid and remove Water Reservoir Cap.
4. Drain water from Water Reservoir into sink or tub.
5. Using Measuring Cup, make a mixture of 8 oz. (236 ml.) vinegar and 8 oz.
(236 ml.) water.
6. Slowly pour water-vinegar solution into Water Reservoir.
7. Allow to stand for 40 minutes.
8. Drain water-vinegar solution from Water Reservoir.
9. Rinse Water Reservoir with fresh water, drain and repeat until vinegar odor
dissipates.
10. Replace Water Reservoir Cap and lower Compartment Lid back down.
11
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
SOLUTION
PROBLEM
POSSIBLE CAUSE
Unit fails to steam. Lighted
On/Off Switch does not
illuminate.
Unit is not plugged in.
Plug into electrical
outlet.
Household Circuit Breaker /
Ground Fault Interrupter has
tripped or blown a fuse.
Reset Circuit Breaker /
Ground Fault Interrupter, or
replace fuse. If you need
assistance, contact a licensed
electrician.
Water Reservoir is empty.
Mineral build-up in unit.
Mineral build-up in unit.
Refill Water Reservoir using
procedures on page 9 of this
manual.
Unit fails to steam. Lighted
On/Off Switch does
illuminate.
Follow Removing Mineral
Build-Up procedure on page
11 of this manual.
Steam output is intermittent.
It is normal for unit to
periodically stop steaming
for a few seconds. If steam
stays off for longer periods,
follow Removing Mineral
Build-Up procedure on page
11 of this manual.
Water condensation in Steam
Hose.
Unit is emitting excess water.
Point Steam Nozzle towards
sink, tub or ground and
shake. Continue until excess
water is released.
Water Reservoir has been
over-filled.
Empty some water out of
Water Reservoir.
Unit has not reached
operating temperature.
Wait until Steam Ready
Light deactivates to steam.
Excessive gurgling in Hose
and Steam Nozzle / water
drips from Steam Nozzle.
Condensation in Steam Hose.
Some gurgling is a natural
effect of steaming process.
For excessive gurgling or
dripping water, extend Hose
vertically to allow water to
drain back into Water
Reservoir.
12
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING & CUSTOMER SUPPORT
SOLUTION
PROBLEM
POSSIBLE CAUSE
Water spills out from Water
Reservoir fill hole when
adding water.
Water Reservoir is already
full.
Do not try to add any more
water.
Water Reservoir is too hot to
be refilled.
Allow more cooling time
before refilling.
Fill Water Reservoir more
slowly. Be sure to utilize the
provided Measuring Cup and
Water Funnel to refill the
unit.
Accessories do not stay
firmly attached to Steam
Nozzle.
Accessories are not being
properly installed.
Review steps for proper
installation of accessories on
page 7 of this manual.
Check to ensure that
accessories are installed
correctly.
Accessories or Steam Nozzle
is damaged or otherwise
incorrect.
Contact our Customer
Service Department for
assistance.
CUSTOMER SUPPORT
For problems with your Fabric Steamer, please refer to the troubleshooting solutions located
on pages 12 & 13 of this manual. Additional inquiries should be directed to our Customer
page.
If you do not have internet access, you may also contact our Customer Support Department
by telephone, at (800) 711-6617 or (816) 584-9700.
NOTE: In order for our customer service representatives to help you as quickly and
efficiently as possible, please have the following information ready before calling:
• Purchase information (where and when you purchased this product)
• Product Serial Number
13
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY INFORMATION
ONE YEAR LIMITED WARRANTY
(If outside USA, additional shipping charges may apply)
Top Innovations, Inc. warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of purchase. This warranty
does not cover damage caused by misuse, negligence, use by improper current or
voltage, commercial use, use contrary to operating instructions or disassembly, repair or
alteration by any person other than Top Innovations, Inc. Warranty Service Department.
Top Innovations, Inc. will repair or replace, at its option. This warranty gives you
specific legal rights and may have other rights, which may vary from state to state.
Performance of any obligation under this warranty may be obtained by:
1. Call (800) 711-6617 for Return Authorization Number before returning for
repair. Failure to obtain a Return Authorization Number will cause a delay in
warranty and out-of-warranty service requests.
2. Include copy of purchase receipt.
3. Include your name, address, telephone number, and Return Authorization
Number on returned package.
Please send product postage-prepaid to:
TOP INNOVATIONS, INC.
WARRANTY SERVICE DEPARTMENT
6655 TROOST AVE.
KANSAS CITY, MO 64131
Should there be any missing or defective parts or accessories, please contact Customer
Support. In most cases, it is not necessary to return the entire unit. We can ship most
parts directly to your door.
Upon expiration of 1 year limited warranty, you will be advised of the cost of repair
before any servicing is done, unless you enclose a note indicating that you would like us
to proceed with repairs.
If you need to request warranty service, or have any questions about coverage under this
warranty, please visit the Warranty Service Request page on our Web site
telephone at (800) 711-6617 or (816) 584-9700, or e-mail
Please have your product serial number ready before contacting Warranty Service
Department. The serial number is located on the back or bottom of your unit.
15
Top Innovations, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Top Innovations, Inc.
6655 Troost Ave.
Kansas City, MO 64131
Tel: (800) 711-6617
(816) 584-9700
Printed in China
PRODUCT SERIAL NUMBER
For your convenience, space has been provided below for
you to record the serial number of your unit (located on the
back or bottom of the unit) for easy reference when
contacting our Customer Service Department.
________________ - ______________________________
V051213
Download from Www.Somanuals.com. All Manuals Search And Download.
|