T
P
A
6
0
3
0
A
4
A
u
d
i
o
P
o
w
e
r
A
m
p
l
i
f
i
e
r
E
v
a
l
u
a
t
i
o
n
M
o
d
u
l
e
User’s Guide
November 2002
Mixed-Signal Products
SLOU113A
Download from Www.Somanuals.com. All Manuals Search And Download.
EVM IMPORTANT NOTICE
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION
PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided
may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective
considerations, including product safety measures typically found in the end product incorporating the goods.
As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic
compatibility and therefore may not meet the technical requirements of the directive.
Should this evaluation kit not meet the specifications indicated in the EVM User’s Guide, the kit may be returned
within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE
WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED,
IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user
indemnifies TI from all claims arising from the handling or use of the goods. Please be aware that the products
received may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). Due to the open construction
oftheproduct, itistheuser’sresponsibilitytotakeanyandallappropriateprecautionswithregardtoelectrostatic
discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE
TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not
exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services described herein.
Please read the EVM User’s Guide and, specifically, the EVM Warnings and Restrictions notice in the EVM
User’sGuidepriortohandlingtheproduct. Thisnoticecontainsimportantsafetyinformationabouttemperatures
and voltages. For further safety concerns, please contact the TI application engineer.
Persons handling the product must have electronics training and observe good laboratory practice standards.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any
machine, process, or combination in which such TI products or services might be or are used.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright 2002, Texas Instruments Incorporated
Download from Www.Somanuals.com. All Manuals Search And Download.
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the supply voltage range of 7 V to 15 V.
Exceeding the specified input range may cause unexpected operation and/or irreversible
damage to the EVM. If there are questions concerning the input range, please contact a TI
field representative prior to connecting the input power.
Applyingloadsoutsideofthespecifiedoutputrangemayresultinunintendedoperationand/or
possible permanent damage to the EVM. Please consult the EVM User’s Guide prior to
connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than
85°C. The EVM is designed to operate properly with certain components above 85°C as long
as the input and output ranges are maintained. These components include but are not limited
tolinearregulators, switchingtransistors, passtransistors, andcurrentsenseresistors. These
types of devices can be identified using the EVM schematic located in the EVM User’s Guide.
When placing measurement probes near these devices during operation, please be aware
that these devices may be very warm to the touch.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright 2002, Texas Instruments Incorporated
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Read This First
How to Use This Manual
This document contains the following chapters:
- Chapter 1—Introduction
- Chapter 2—Quick Start
- Chapter 3—Reference
Information About Cautions and Warnings
This book may contain cautions and warnings.
This is an example of a caution statement.
A caution statement describes a situation that could potentially
damage your software or equipment.
This is an example of a warning statement.
A warning statement describes a situation that could potentially
cause harm to you.
The information in a caution or a warning is provided for your protection.
Please read each caution and warning carefully.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Documentation From Texas Instruments
Related Documentation From Texas Instruments
J
TI Plug-N-Play Audio Amplifier Evaluation Platform (literature
number SLOU011) provides detailed information on the evaluation
platform and its use with TI audio evaluation modules.
J
TPA6030A4 3-W Stereo Audio Power Amplifier With Advanced
DC Volume Control (literature number SLOS395). This is the data
sheet for the TPA6030A4 audio amplifier integrated circuit.
FCC Warning
This equipment is intended for use in a laboratory test environment only. It
generates, uses, and can radiate radio frequency energy and has not been
tested for compliance with the limits of computing devices pursuant to subpart
J of part 15 of FCC rules, which are designed to provide reasonable protection
against radio frequency interference. Operation of this equipment in other
environments may cause interference with radio communications, in which
case the user at his own expense will be required to take whatever measures
may be required to correct this interference.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.1
1.2
1.3
1.4
Feature Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
TPA6030A4EVM Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Special Notes Regarding the Data Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
2
3
Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1
2.2
2.3
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Quick Start List for Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Quick Start List for Stand-Alone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1
3.2
3.3
TPA6030A4EVM Layout and Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
TPA6030A4 Audio Power Amplifier Evaluation Module Parts List . . . . . . . . . . . . . . . . . . 3-4
Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Figures
1–1
2–1
2–2
2–3
2–4
2–5
3–1
3–2
3–3
The TI TPA6030A4 Audio Amplifier Evaluation Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Quick Start Platform Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Module Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Quick Start Module Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
TPA6030A4EVM Connected for Stereo Bridge-Tied Load (BTL) Output . . . . . . . . . . . . . . 2-8
TPA6030A4EVM Connected for Stereo Single-Ended (SE) Output . . . . . . . . . . . . . . . . . . . 2-8
TPA6030A4EVM Top Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
TPA6030A4EVM Bottom Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
TPA6030A4EVM Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
2–1
2–2
2–3
2–4
2–5
3–1
3–2
Typical TI Plug-N-Play Platform Jumper and Switch Settings for the TPA6030A4 . . . . . . 2-2
Typical TPA6030A4EVM Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Platform Jumper and Switch Settings for the TPA6030A4 . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Typical TPA6030A4EVM Jumper Settings for BTL Stand-Alone . . . . . . . . . . . . . . . . . . . . . 2-8
Typical TPA6030A4EVM Jumper Settings for SE Stand-Alone . . . . . . . . . . . . . . . . . . . . . . 2-8
TPA6030A4EVM Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Volume Control (V
= 12 V, No Load, SEDIFF = 0 V, SEMAX = 5VREF) . . . . . . . . . . . . 3-5
CC
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
This chapter provides an overview of the Texas Instruments (TI) TPA6030A4
audio amplifier evaluation module (SLOP365). It includes a list of EVM
features, a brief illustrated description of the module, and a list of EVM
specifications.
Topic
Page
1.1 Feature Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2
1.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3
1.3 TPA6030A4EVM Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3
1.4 Special Notes Regarding the Data Sheet . . . . . . . . . . . . . . . . . . . . . . . . 1–4
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Feature Highlights
1.1 Feature Highlights
The TI TPA6030A4 audio amplifier evaluation module and the TI Plug-N-Play
audio amplifier evaluation platform include the following features:
- TPA6030A4 3-W stereo audio power amplifier evaluation module
J
Fully differential operation and internal depop circuitry to minimize
transients in outputs
J
J
J
J
J
J
3 W per channel output power into 16 Ω, BTL, at V
= 12 V
CC
Low current consumption in shutdown mode (1 µA)
Internal input mux selects among two sets of stereo inputs
Stereo, bridge-tied load (BTL) or single-ended (SE) operation
DC voltage volume control from 36 dB to –40 dB, and a –80 dB mute
SE gain adjustable from 30 dB to –46 dB, and a –86 dB mute
- Quick and easy configuration with the TI Plug-N-Play audio amplifier eval-
uation platform
J
Evaluation module is designed to simply plug into the platform,
automatically making all signal and power connections
J
J
J
J
Platform provides flexible power options
Jumpers on the platform select power and module control options
Switches on the platform route signals
Platform provides quick and easy audio input and output connections
- Platform power options
J
J
J
J
External 5-V to 15-V dc V
supply inputs
CC
External regulated V
supply input
DD
Socket for onboard 5 V/3.3 V V
voltage regulator EVM
DD
Onboard overvoltage and reverse polarity power protection
- Platform audio input and output connections
J
J
J
J
J
Left and right RCA phono jack inputs
Miniature stereo phone jack input
Left and right RCA phono jack outputs
Left and right compression speaker terminal outputs
Miniature stereo headphone jack output
1-2
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
1.2 Description
The TPA6030A4 stereo 3-W audio power amplifier evaluation module is
designed to demonstrate all of the different features and benefits of the
TPA6030A4amplifier. ItconsistsoftheTITPA6030A4stereo3-Waudiopower
amplifier IC along with a small number of other parts mounted on a circuit
board that measures approximately 2 1/4 inches by 1 1/2 inches (Figure 1–1).
Figure 1–1. The TI TPA6030A4 Audio Amplifier Evaluation Module
Single in-line header pins extend from the underside of the module circuit
board to allow the EVM to be plugged into the TI Plug-N-Play audio amplifier
evaluation platform, or to be wired directly into existing circuits and equipment
when used stand-alone.
The platform has room for a single TPA6030A4 evaluation module and is a
convenient vehicle for demonstrating TI’s audio power amplifier and related
evaluation modules. The EVM simply plugs into the platform, which
automatically provides power to the modules, interconnects them correctly,
andconnectsthemtoaversatilearrayofstandardaudioinputandoutputjacks
and connectors. Easy-to-use configuration controls allow the platform and
EVMs to quickly model many possible end-equipment configurations.
There is nothing to build, nothing to solder, and nothing but the speakers
included with the platform to hook up.
1.3 TPA6030A4EVM Specifications
Supply voltage range, V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V to 15 V
CC
Supply current, I
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 A max
DD
Continuous output power per channel, P : 16-Ω BTL, V =12 V . . . . . 3 W
O
CC
Audio input voltage, V : HP input . . . . . . . . . . . . . . . . . . . . . . . . V
+ 0.3 V
I,
CC
LINE input . . . . . . . . . . . . . . . . . . . . . . V
+ 0.3 V
CC
†
Minimum load impedance, R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω
L
†
V
= 7 V is recommended for this load.
CC
1-3
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Notes Regarding the Data Sheet
1.4 Special Notes Regarding the Data Sheet
The TPA6036A4EVM may have markings not consistent with the data sheet.
Some EVMs have an incorrect supply voltage marked on them. The correct
supply range is 7 V to 15 V, not 5 V to 15 V.
The EVM and this user’s guide refer to the two input pins as HP and LINE, and
refer to the control pin as HP/LINE. The data sheet refers to the two inputs as
IN2 and IN1, respectively, and the control pin as IN2/IN1.
See the data sheet for the correct voltages and pin names.
1-4
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Quick Start
The steps in this chapter can be followed to quickly prepare the TPA6030A4
audio amplifier EVM for use. Using the TPA6030A4 with the TI Plug-N-Play
audio amplifier evaluation platform is a quick and easy way to connect power,
signal and control inputs, and signal outputs to the EVM using standard
connectors. However, the audio amplifier evaluation module can be used
stand-alone by making connections directly to the module pins, and can be
wired directly into existing circuits or equipment.
The TI Plug-N-Play platform supplies a 5-V regulated voltage that is designed
to allow devices with an SE/BTL pin to automatically switch to SE output mode
when a headphone is inserted into the headphone jack. The SE/BTL pin on
the TPA6030A4 is designed to switch high when the voltage applied to the pin
meets or exceeds 0.8 V , requiring a minimum of 5.6 V when the power
CC
supply is at 7 V. This is more than the platform can supply, and consequently,
the automatic SE/BTL toggle feature of the TI Plug-N-Play platform is not fully
compatible with the TPA6030A4EVM. However, the output mode can be
manually changed with the use of J1 on the TPA6030A4EVM (see Table 2–2).
Refer to the application section of the TPA6030A4 data sheet for more
information about building a circuit that automatically switches output modes
when a headphone is inserted.
The jumper and switch settings on the TI Plug-N-Play platform do not change
with different V
levels.
CC
Topic
Page
2.1 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
2.2 Quick Start List for Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4
2.3 Quick Start List for Stand-Alone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 2–1. Typical TI Plug-N-Play Platform Jumper and Switch Settings for the TPA6030A4
EVM
JP5
JP6
JP7
JP8
S2
S3
P-N-P Platform
OFF
Mode
X
X
Note 4
X
Notes: 1) X = Don’t care
2) ON = Shunt installed
3) OFF = Open
4) Set S2 to ON when signal conditioning board is installed in U1; set S2
to OFF when no signal conditioning board is installed.
Table 2–2. Typical TPA6030A4EVM Jumper Settings
EVM
Mode
BTL
SE
J1
OFF
ON
J2
X
J3
OFF
OFF
TPA6030A4
X
Notes: 1) ON = Shunt installed
2) OFF = Open
3) X = Don’t care
2-2
Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
2.1 Precautions
Power Supply Input Polarity and Maximum Voltage
Always ensure that the polarity and voltage of the external power
connected to V power input connector J1, J2, and/or V power
CC
DD
input connector J6 are correct. Overvoltage or reverse-polarity
power applied to these terminals can open onboard soldered-in
fuses and cause other damage to the platform, installed evaluation
modules, and/or the power source.
Inserting or Removing EVM Boards
Do not insert or remove EVM boards with power applied—damage
to the EVM board, the platform, or both may result.
Figure 2–1. Quick Start Platform Map
1
ICC
JP4
C1+
F1
VR1
6
DC
Power
In/Out
Power
Input
R2
5
R1
Audio
Power
Amps
Signal Conditioning
9
Audio
Input
Speaker
Output
8
7
Mode
Mute
Polarity
Lo
****CAUTION****
Do not insert or remove
EVM boards with power
applied
4
Hi
Stereo
Headphone
Output
Plug-N-Play Audio Amplifier
Evaluation Platform
SLOP097 Rev. C.1
R3
R4
HP Out
R5
3
2
2-3
Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start List for Platform
2.2 Quick Start List for Platform
Follow these steps when using the TPA6030A4EVM with the TI Plug-N-Play
audio amplifier evaluation platform (see the platform user’s guide, SLOU011,
for additional details). Numbered callouts for selected steps are shown in
Figure 2–1 and Figure 2–2:
Note:
The TI Plug-N-Play platform sends the input signal to both the HP and LINE
inputs automatically, and only to the positive inputs. To fully take advantage
oftheTPA6030A4differentialinputaswellastheinputmodeselectablemux,
the EVM should be used in a stand-alone fashion.
- Platform Preparations
1) EnsurethatallexternalpowersourcesaresettoOFFandthattheplatform
power switch S1 is set to OFF.
2) Install a TPA6030A4 module in platform socket U2, taking care to align the
module pins correctly.
3) Use switch S2 to select or bypass the signal conditioning EVM (U1).
4) Set jumper JP6 to select the Mode control input.
5) Remove jumper JP5.
Table 2–3. Platform Jumper and Switch Settings for the TPA6030A4
EVM
P-N-P Platform
JP5
Off
JP6
Mode
JP7
JP8
S2
S3
X
Hi
Note 4
X
Notes: 1) X = Don’t care
2) ON = Shunt installed
3) OFF = Open
4) Set S2 to ON when signal conditioning board is installed in U1; set S2
to OFF when no signal conditioning board is installed.
- Power Supply
6) Select and connect an external regulated power supply (ensure power
supply is turned OFF) set from 7 V to 15 V to platform V power input
CC
connector J1, taking care to observe marked polarity. Jumper the
appropriate power input.
- Inputs and Outputs
7) Ensure that the audio signal source level is set to minimum.
8) Connect the audio source to left and right RCA phono jacks J3 and J5 or
stereo miniature phone jack J4.
9) Connect speakers to left and right RCA jacks J7 and J9 or to stripped wire
speaker connectors J8.
2-4
Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start List for Platform
- Evaluation Module Preparations
Figure 2–2. Module Preparation
13
12
10
11
10) The SE jumper, J1, is used to select between the two output modes, SE
and BTL. To allow the module SE/BTL control input to force the amplifier
IC into a BTL output mode, set output mode jumper J1 to OFF. To keep
the module amplifier IC in the single-ended output mode regardless of the
control input state, set jumper J1 to ON.
11) The HP jumper, J2, is used to select between the two input modes, HP and
LINE. To keep the amplifier IC in LINE input mode, set J2 to OFF. To keep
the amplifier IC in the HP input mode, set jumper J2 to ON.
- Power Up
Platform LED1 should light indicating the presence of V , and the evaluation
CC
modules installed on the platform should begin operation.
- Volume Control
12) Potentiometer R1 (VOLUME) sets the BTL volume, which can range from
–40 dB to +36 dB using 2.53 dB steps. Turning the potentiometer
clockwise increases the gain; turning counterclockwise decreases the
gain. To mute the volume (–80 dB), turn the poteniometer, R1, as far as
it will go in a counterclockwise direction. Refer to Table 3–2 in the
Reference chapter for a list of the volume levels.
13) The SE volume may be set independently using potentiometers R2
(SEDIFF) and R3 (SEMAX). SEDIFF set the difference between the BTL
volume and the SE volume, while SEMAX sets the maximum volume in
SE mode.
14) Turning potentiometer R2 (SEDIFF) clockwise decreases the difference
between SE and BTL volumes; counterclockwise increases the
difference.
15) Turning potentiometer R3 (SEMAX) clockwise increases the maximum
SE volume; counterclockwise decreases the maximum SE volume.
For more information on volume control operation, see the TPA6030A4 data
sheet.
2-5
Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start List for Stand-Alone
2.3 Quick Start List for Stand-Alone
Follow these steps to use the TPA6030A4EVM stand-alone or when
connecting it to existing circuits or equipment. Connections to the TPA6030A4
module header pins can be made via individual sockets, wire-wrapping, or
solderingtothepins, eitheronthetoporthebottomofthemodulecircuitboard.
Numbered callouts for selected steps are shown in Figure 2–3.
Figure 2–3. Quick Start Module Map
8
6
7
- Power Supply
1) Ensure that all external power sources are set to OFF.
2) Connect an external regulated power supply set from 7 V to 15 V to the
module V and GND pins taking care to observe marked polarity.
CC
- Inputs and Outputs
3) Ensure that audio signal source level adjustments are set to minimum.
4) Connect the right (or left) positive lead of the audio source to the module
R LINE+ (or L LINE+) pins and the negative lead to the R LINE– (or
L LINE–) pins. If using the headphone inputs, connect the positive audio
source to the module R HP+ (L HP+) and the negative lead to R HP–
(L HP–). The inputs can be used with a differential or single-ended audio
source. If stereo use is desired, connect both right and left inputs to the
appropriate sources.
5) Select output mode:
a) For BTL output, connect a speaker to the module OUT+ and OUT–
pins of each channel, (see Figure 2–4)
or
b) For single-ended output, connect a headphone or a speaker to the
module OUT+ and GND pins of each channel through a 33 µF to
1000 µF output-coupling capacitor (Figure 2–5).
2-6
Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start List for Stand-Alone
- Evaluation Module Preparations
6) To force the EVM into a BTL output mode, set jumper J1 to OFF. To force
the EVM into a SE output mode, set jumper J1 to ON.
7) To force the EVM into using the LINE inputs, set jumperJ2 to OFF. To force
the EVM into using HP inputs, set jumper J2 to ON.
- Control Inputs
8) To allow the amplifier IC to switch from the LINE inputs to the HP inputs
when the output switches from BTL output mode to SE output mode and
vice versa, set jumper J3 to ON. To allow the inputs and output modes to
switch independently, set jumper J3 to OFF. Connect control lines to the
various module control input pins as needed.
9) SE/BTL: A high voltage applied to this pin selects the SE output mode; a
low voltage or float on this pin selects the BTL output mode. Refer to the
TPA6030A4 data sheet for trip level information.
10) SHUTDOWN: A low voltage applied to this pin shuts down the amplifier
IC on the module; a high voltage or float on this pin allows normal
operation. Refer to the TPA6030A4 data sheet for trip level information.
- Power-Up
11) Verify correct voltage and input polarity and set the external power supply
to ON.
The EVM should begin operation.
- Volume Control
12) Potentiometer R1 (VOLUME) sets the BTL volume, which can range from
–40 dB to +36 dB using 2.53 dB steps. Turning the potentiometer
clockwise increases the volume; turning counterclockwise decreases the
volume. To mute the volume (–80 dB), turn the potentiometer, R1, as far
as it will go in a counterclockwise direction. Refer to Table 3–2 in the
Reference chapter for a list of the volume levels.
13) The SE volume may be set independently using potentiometers R2
(SEDIFF) and R3 (SEMAX). SEDIFF set the difference between the BTL
volume and the SE volume, while SEMAX sets the maximum volume in
SE mode.
14) Turning potentiometer R2 (SEDIFF) clockwise decreases the difference
between the volumes; counterclockwise increases the difference.
15) Turning potentiometer R3 (SEMAX) clockwise increases the maximum
SE volume; counterclockwise decreases the maximum SE volume.
For more information on volume control operation, see the TPA6030A4 data
sheet.
2-7
Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start List for Stand-Alone
Figure 2–4. TPA6030A4EVM Connected for Stereo Bridge-Tied Load (BTL) Output
Audio
Input
Right
External Shut
Down Control
(active low)
Audio
Input
Left
Power Supply
Table 2–4.Typical TPA6030A4EVM Jumper Settings for BTL Stand-Alone
EVM
J1
J2
J3
TPA6030A4
OFF
OFF
OFF
Note: ON = Shunt installed
OFF = Open
Figure 2–5. TPA6030A4EVM Connected for Stereo Single-Ended (SE) Output
+
33 µF –
1000 µF
Audio
Input
33 µF –
1000 µF
Audio
Input
+
Power Supply
Table 2–5.Typical TPA6030A4EVM Jumper Settings for SE Stand-Alone
EVM
J1
J2
J3
TPA6030A4
ON
ON
OFF
Note: ON = Shunt installed
OFF = Open
2-8
Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Reference
This chapter contains reference information pertaining to the layout and
schematic of the TPA6030A4EVM. Also included is the volume control table
for the TPA6030A4.
Topic
Page
3.1 TPA6030A4EVM Layout and Schematic . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
3.2 TPA6030A4 Audio Power Amplifier Evaluation Module
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4
3.3 Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–5
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
TPA6030A4EVM Layout and Schematic
3.1 TPA6030A4EVM Layout and Schematic
Figure 3–1. TPA6030A4 EVM Top Layer
Figure 3–2. TPA6030A4EVM Bottom Layer
3-2
Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
TPA6030A4EVM Layout and Schematic
Figure 3–3. TPA6030A4EVM Schematic
3-3
Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
TPA6030A4 Audio Power Amplifier Evaluation Module Parts List
3.2 TPA6030A4 Audio Power Amplifier Evaluation Module Parts List
Table 3–1.TPA6030A4EVM Parts List
EVM
Qty.
Manufacturer/
Part Number
Distributor’s
Number
Reference
Description
Size
C9, C11, C12, Capacitor, 1 µF,
0805
4
Panasonic
ECJ–2VF1C105Z
Digi-Key
PCC1849TR-ND
C15
80%/–20%, nonpolarized,
16 V
C1, C2, C3,
C4, C5, C6,
C7, C8
Capacitor, 0.47 µF,
80%/–20%, nonpolarized,
16 V
0805
8
Panasonic
ECJ–2VF1C474Z
Digi-Key
PCC1847TR-ND
C13, C14
Capacitor, 10 µF, 16 V
B
2
1
Panasonic
ECS-T1CX106R
Digi-Key
PCS3106TR-ND
C10
Capacitor, 47 nF,
80%/–20%, nonpolarized,
25 V
0805
Murata
GRM216F51E473ZA01D
R4, R5, R6
R1, R2, R3
S1
Resistor, 510 kΩ, 1/10 W
0805
3
3
1
3
3
1
Panasonic
ERJ-6GEYJ514
Digi-Key
P510KATR-ND
Potentiometer, 100 kΩ,
Cermet ST SL, thru hole
Bourns
33362P–1–104
Digi-Key
3362P–104–ND
Switch, momentary
Header, 2 position
Shunts
SMD
2 mm
2 mm
Panasonic
EVQ-PJX04M
Digi-Key
P8050SCT-ND
J1, J2, J3
Norcomp
2163-2-01-P2
Digi-Key
2163S-02-ND
2JM–G
Digi-Key
SPE1302–ND
U1
IC, TPA6030A4, audio
amplifier
28 pin
TSSOP
TI
TPA6030A4PWP
3-4
Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume Control
3.3 Volume Control
Table 3–2.Volume Control (V
= 12 V, No Load, SEDIFF = 0 V, SEMAX = 5VREF)
CC
Voltage On VOLUME Pin as a
Speaker Volume
Headphone Volume
Percenatge of 5VREF
0–10
(dB)
–80.00
–40.00
–37.47
–34.93
–32.40
–29.87
–27.33
–24.80
–22.27
–19.73
–17.20
–14.67
–12.13
–9.60
–7.07
–4.53
–2.00
0.53
(dB)
–86.00
–46.00
–43.47
–40.93
–38.40
–35.87
–33.33
–30.80
–28.27
–25.73
–23.20
–20.67
–18.13
–15.60
–13.07
–10.53
–8.00
–5.47
–2.93
–0.40
2.13
10–12.6
12.6–15.2
15.2–18
18–20.6
20.6–23.4
23.4–26
26–28.6
28.6–31.4
31.4–34
34–36.6
36.6–39.4
39.4–42
42–44.6
44.6–47.2
47.2–50
50–52.6
52.6–55.4
55.4–58
3.07
58–60.6
5.60
60.6–63.4
63.4–66
8.13
10.67
13.20
15.73
18.27
20.80
23.33
25.87
28.40
30.93
33.47
36.00
4.67
66–68.6
7.20
68.6–71.4
71.4–74
9.73
12.27
14.80
17.33
19.87
22.40
24.93
27.47
30.00
74–76.6
76.6–79.4
79.4–82
82–84.6
84.6–87.4
87.4–90
90–100
3-5
Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
|