Operating Instructions
BP-1002/BP-2002 Beltpacks
Audicom Intercom Systems
9350-7740-000 Rev K
08/2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Table
Of
Contents
Introduction ..........................................................................................1
External Connections and Controls ......................................................3
Operation ..............................................................................................5
System Power ........................................................................................5
Initial BP-1002/2002 Setup ..................................................................5
Operating Modes ..................................................................................5
Changing Modes of Operation .............................................................6
Internal Switches, Jumpers and Adjustments .......................................6
Sidetone Adjustment (R145) ..................................................................7
Mic Gain Adjustment (R156) ................................................................7
Clear-Com Setup ...................................................................................8
BP-1002/2002 .......................................................................................8
Connector Pin Configurations ..............................................................9
Specifications ......................................................................................10
Optional Football Modifications ........................................................11
General Description ...........................................................................11
Eliminating Mic-Kill and Call Signal .................................................11
Restoring Mic-Kill and Call Signal ....................................................11
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
Introduction
WARNING:
If you have a BP-1002/2002 with a 9030-7740-XXX circuit board,
you will need to obtain Revision H of this user manual.
®1
The Audiocom BP-1002 and BP-2002 are microprocessor controlled one- and
two-channel intercom beltpacks. An internal switch and jumper setting allows the
®2
units to be used with Clear-Com components, if desired. Other internal switch and
jumper settings allow the unit to be uniquely configured to the operator’s
requirements.
®
1. Audiocom is a registered trademark of Telex Communications, Inc., Burnsville, MN
55337.
®
2. Clear-Com is a registered trademark of Clear-Com Intercom Systems.
Introduction
1
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 1. BP-2002 & BP-1002 Connections and Controls
2
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
External Connections and Controls
NOTE:
The numbers refer to the callouts in Figure 1.
1.
2.
Volume Control -
Use this control to adjust the headset listen level.
Chan Button and
Indicators -
The Chan button (only on the BP-2002) allows the
user to select which intercom channel is active. Press
the Chan button to change the channel selection. The
yellow indicator next to the channel number lights to
show the active channel.
3.
Call Button and Indicator -
The Call function allow the user to send or receive
signals to other devices on the intercom channel
selected. The call button operates in two ways:
•
Call Receive: When there is an incoming call
signal, the indicator is red. (If Audible Call Alert
is enabled, incoming calls will cause beeps in
the headset.) ON the BP-2002, call can be sent
on the selected channel only.
•
Call Send: To send a call signal to all stations on
a channel, press and hold the Call button until a
verbal response is received. The indicator will
glow red. On the BP-2002, calls can be sent on
the selected channel only.
4.
Talk Button and
Indicator -
The Talk button activates the headset microphone and
operates in two ways:
•
Latched Mode: Tap the button once to talk. The
indicator will glow green. Tap the button again
when finished with a conversation.
•
Momentary Mode: Press and hold the button to
talk momentarily. Release the button when
finished talking.
NOTE:
On the BP-2002, if no headset is connected, when the Talk button is
pressed, the Talk button will have the same function as the Chan button.
Introduction
3
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Sidetone Control -
When using a headset, this control adjusts your own
voice level heard in the headphones. To adjust the
level, tap the Talk button once to turn ON the headset
microphone. Then, use a small Phillips head
screwdriver to increase or decrease your voice level
while talking into the microphone. (This control is
accessible by removing one screw in the belt clip.)
®
6.
7.
Headset Connector -
This connector accepts a four-wire Telex boom-
microphone headset.
Intercom Channel
Connectors -
On the BP-2002, intercom channels are connected via
a pair of 6-pin connectors (one male and one female).
The male and female connectors are wired together in
parallel, providing a “loop-through” at each
connector pin. Use one connector to connect to the
intercom channel. Use the other connector to “daisy
chain” a cable to the next beltpack or other station on
the channel.
Local Power Input - Normally the BP-2002 is
powered from the intercom system and will turn
ON with the intercom system. The BP-2002
beltpack may also be powered from an optional
power supply (21-30 VDC) connected between
pin 2(+) and pin 1 (-) of the intercom channel
connector.
8.
Intercom Channel
Connectors -
On the BP-1002, the intercom channel is connected
via a pair of 3-pin connectors (one male and one
female). The male and female connectors are wired
together in parallel, providing a “loop through” at
each connector pin. Use one connector to connect to
the intercom channel. Use the other connector to
“daisy chain” a cable to the next beltpack or other
station on the channel.
4
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
Operation
System Power
The BP-1002/2002 beltpack receives power externally in one of two ways:
•
•
The intercom channel
The local power (pin 2) of the intercom channel connector (BP-2002
only)
Both the BP-1002 and BP-2002 will pass system power through to subsequent
beltpacks that are “daisy chained” together.
Initial BP-1002/2002 Setup
The channel termination is initially set for balanced operation, which is compatible
®
with other Audiocom equipment. If the unit is going to be connected to Clear-Com
equipment, one switch must be changed as described in the section on Clear-Com
setup in this manual.
The headset microphone type is auto-sensing, which means it automatically
determines if an Electret or Dynamic headset is attached to the unit.
Operating Modes
The microprocessor within the BP-1002/2002 controls four (4) modes of operation
that affect the Microphone Kill and Audible Call Alert features. These modes can be
seen in Table 1 on page 6.
Operation
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Modes of Operation
Perform the following steps to change the mode of operation.
NOTE:
Both the Talk and Call indicators should be OFF and the headset should
be connected.
9. Press and hold the Talk key, and then press and hold the Call key.
10. Release both keys.
The Call indicator should now glow red. (The number of beeps heard in the
headset indicates the current mode of operation.)
11. Press the Call key to change to the next mode of operation.
Each press of the Call key will cause the BP-1002/2002 to change to the next
mode of operation.
12. When the desired mode is reached, press the Talk key to select that mode
and exit the mode changing function.
Beeps will be heard in the headset when the mode changing function is
exited. The number of beeps hears indicates the selected mode of operation.
NOTE:
Each time the intercom system power is turned ON, the
beltpack will reset to the default mode of operation (mode
2).
TABLE 1. Modes of Operation
Mode (beeps)
Mic Kill
Disabled
Enabled
Audible Call Alert
Disabled
1
2 (default)
Disabled
3
4
Disabled
Enabled
Enabled
Enabled
Internal Switches, Jumpers and Adjustments
There are several internal switches, jumpers, and adjustments that affect operation.
These are described below. To gain access to the switches, jumpers and adjustments,
disconnect all power and line connections. Remove two screws from the top of each
side and two screws from the bottom of each side. Switch, jumper and adjustment
locations are shown in Figure 2.
6
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 2. Internal Switches, Jumpers, and Adjustments
NOTE:
Figure 2 shows a BP-2002 with the switches and jumpers in their factory
default positions. SW5 does not exist on the BP-1002 board.
The Sidetone and Mic Gain adjustment are also accessible behind the screw that holds
the belt clip (callout 5 in Figure 1)
The functions of the internal switches and jumpers are described in Table 2 on page 8.
Sidetone Adjustment (R145)
The sidetone adjustment is accessible either internally (refer to Figure 3) or by
removing the belt clip mounting screw (callout 5 in Figure 1 on page 2).
To adjust the level of your own voice heard in the headphones, tap the Talk button
once to turn ON the headset microphone. Then, use a small Phillips head screwdriver
to increase or decrease your voice level while talking into the microphone.
Mic Gain Adjustment (R156)
The Mic Gain Adjustment is accessible internally on the board (R156) (refer to
Figure 3) or by removing the belt clip mounting screw (callout 5 in Figure 1 on
page 2).
Operation
7
Download from Www.Somanuals.com. All Manuals Search And Download.
To adjust mic gain, do the following:
>
Using a Phillips head screw driver, turn the Mic Gain pot clockwise to
increase the gain (or counter-clockwise to decrease the gain).
Clear-Com Setup
Make the following switch and jumper changes when the beltpack is used with
Clear-Com equipment.
BP-1002/2002
>
SW1 must be placed in the UNBAL position.
TABLE 2. Internal Switches and Jumpers
Jumper/
Default
Setting
Switch
Jumper or Switch Function
Number
Power Select
Channel One Power: pins 2 & 3 shorted
(On BP-1002, pins 2 & 3 are always shorted
Pins 2 & 3 are
shorted
JP1 and JP2
SW1
Channel Two Power: pins 1 & 2 are shorted
Clear-Com/Audiocom®
BAL
Unbalanced/Balanced Line
Pins 2 & 3
shorted
JP3
JP5
Must be left on default
Pins 1 & 2 Shorted
Pins 1 & 2
shorted
8
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Connector Pin Configurations
Headset Connector
Type: XLR-4M (callout in Figure 1)
Pin 1
Headset Microphone Low
Pin 2
Pin 3
Pin 4
Headset Microphone High
Headphone High
Headphone Low
Intercom Channel Connectors
BP-1002
Type: One XLR-3M and XLR-3F pair (callout 8 in Figure 1)
®
Audiocom Mode (Internal switch SW1 set to BAL position)
Pin 1
Pin 2
Pin 3
®
Common
Intercom audio/call low and +24VDC input
Intercom audio/call high and +24VDC input
Clear-Com Mode (Internal switch SW1 set to UNBAL position)
Pin 1
Pin 2
Pin 3
Common
+30VDC input
Intercom audio/call signal
BP-2002
Type: One XLR-6M and XLR-6F pair (callout 7 in Figure 1)
®
Audiocom Mode (Internal switch SW1 set to BAL position)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Common
Local Power (21-30VDC)
Channel A intercom audio/call low and +24VDC input
Channel A intercom audio/call high and +24VDC input
Channel B intercom audio/call low and +24VDC input
Channel B intercom audio/call high and +24VDC input
Pin 6
®
Clear-Com Mode (Internal switch SW1 set to UNBAL position)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Common
Local Power (21-30VDC)
Channel A +30 VDC input
Channel A intercom audio/call signal
Channel B +30VDC input
Channel B intercom audio/call signal
Operation
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General
Power Requirements:
Channel Supplied: 24VDC nominal, 40 to 100mA
Local Power: 24VDC nominal (21 to 30VDC), 40 to 100mA
Environmental Requirements:
Storage: -20°C to 80°C; 0% to 95% humidity, non-condensing
Operating: -15°C to 60°C; 0% to 95% humidity, non-condensing
Dimensions: 5.0” (127mm) H x 3.5” (88.9mm) W x 1.8” (45.7mm) D
Weight: 13oz. (0.4kg)
Interface Requirements
Headset:
1000-3000 Ohm electret microphone
50-200 Ohm dynamic microphone
150-600 Ohm headphones
Input Level:
4mVRMS (nominal)
Balanced Intercom Channel:
Output Level: 1 VRMS nominal
Terminating Impedance: 300 Ohm ±10%
Bridging Impedance: greater than 10,000 Ohm
Call Signaling
Send: 20kHz ±100Hz, 500mVRMS ±10%
Receive: 20kHz ±800Hz, 100mVRMS
Mic-Off Frequency
Detect: 24kHz ±800Hz, 100mVRMS
Noise Contribution: less than -60dBu on the line
Total Harmonic Distortion: less than 1% at channel output for normal input
Unbalanced Intercom Channel:
Output Level: 775mVRMS ±10%
Terminating Impedance: 200 Ohm ±10%
Bridging Impedance: greater than 10,000 Ohm
Call Signaling
Send: 12 ±3VDC on the line
Receive: 4 -15VDC from the line
Total Harmonic Distortion: less than 1% at channel output for normal input
Headphone Amplifier
Maximum Output:
4.5 ±10% Vrms into 150Ω headset
Frequency Response:
200Hz to 8kHz ±2dB
Audible Alert:
1kHz, at the headset
Total Harmonic Distortion:
Less than 1% at less than 3.5VRMS into 150Ω headset
Sidetone:
17dB minimum range, adjustable
10 Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Football Modifications
General Description
In Audiocom® Intercom Systems, the Mic-Kill feature is used to turn OFF any
activated microphones on a selected channel. The Mic-Kill feature is activated when
the beltpack receives a 24kHz signal from the channel. In some application the Mic-
Kill and Call Signal features are not desired and need to be disabled.
Eliminating Mic-Kill and Call Signal
CAUTION: To prevent damage to the equipment, these modifications should only be
made by qualified technicians.
If desired, the Mic-Kill and Call Signal features can be disabled in the BP-2002/1002
by removing a surface mounted capacitor from the printed circuit board.
To remove the capacitor, do the following:
1. Before making changes to the printed circuit board, disconnect all power and
line connections from the beltpack.
2. Refer to Figure 3 and locate C61 on the underside of the printed circuit
board.
3. Remove capacitor C61 from the printed circuit board.
Restoring Mic-Kill and Call Signal
®
To restore the Mic-Kill and Call Signal features, replace C61 with Telex part
number 102881-140, 1500pF, 50V capacitor.
Operation 11
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 3. Printed Circuit Board
12 Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Operation 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|