Teledex IP Phone DC9200 User Manual

Caution: Users should not attempt to make such connections themselves, but  
should contact the appropriate electric inspection authority or electrician, as  
appropriate.  
THIS PRODUCT SHOULD NOT BE PLACED IN A BUILT-IN INSTALLATION  
UNLESS PROPER VENTILATION IS PROVIDED.  
7. NEVER PUSH OBJECTS OF ANY KIND INTO THIS PRODUCT THROUGH  
CABINET SLOTS AS THEY MAY TOUCH DANGEROUS VOLTAGE POINTS  
OR SHORT OUT PARTS THAT COULD RESULT IN A RISK OF FIRE OR  
ELECTRIC SHOCK. NEVER SPILL LIQUID OF ANY KIND ON THE PRODUCT.  
8. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT DISASSEMBLE  
THIS PRODUCT. BUT TAKE IT TO A QUALIFIED SERVICE FACILITY IF  
SERVICE OR REPAIR WORK IS REQUIRED. OPENING OR REMOVING  
COVERS MAY EXPOSE YOU TO DANGEROUS VOLTAGES OR OTHER  
RISKS. INCORRECT REASSEMBLY CAN CAUSE ELECTRIC SHOCK WHEN  
THE APPLIANCE IS SUBSEQUENTLY USED.  
The Ringer Equivalence Number (REN) of this device is 0.7B.  
Notice: The Ringer Equivalence Number (REN) assigned to each terminal  
device provides an indication of the maximum number of terminals  
allowed to be connected to a telephone interface. The termination on an  
interface may consist of any combination of devices subject only to the  
requirement that the sum of the Ringer Equivalence Numbers of all the  
devices does not exceed 5. This telephone connects to the telephone  
network under the connecting arrangement code CA11A.  
DC9200 SERIES USERS GUIDE  
900 MHz Two-Line Digital Cordless Guestroom Telephone  
INCLUDED IN YOUR PACKAGE  
3. Ensure that the handset charging contacts at the bottom of  
Cordless Handset  
Base Unit  
AC Adapter  
the handset are making good contact with the base unit’s  
charging contacts.  
User Guide  
9. UNPLUG THIS PRODUCT FROM THE WALL OUTLET AND REFER  
SERVICING TO QUALIFIED SERVICE PERSONNEL UNDER THE FOLLOW-  
ING CONDITIONS:  
NiMH Battery  
10-foot, 4-wire RJ-11 Line Cord  
15-foot, 8-wire RJ-45 Cable  
Clear Plastic Overlay  
IMPORTANT SAFETY INSTRUCTIONS  
Rubber Battery Screw Cover  
Phillips Screw  
CLEANING THE BATTERY CONTACTS  
WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAU-  
TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE,  
ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING THE FOLLOWING:  
1. READ AND UNDERSTAND ALL INSTRUCTIONS.  
To maintain a good charge, it is important to clean all charging  
contacts on the handset and base unit. Use a pencil eraser or  
other contact cleaner. Do not use any liquids or solvents.  
- WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED OR FRAYED.  
- IF LIQUID HAS BEEN SPILLED INTO THE PRODUCT.  
- IF THE PRODUCT HAS BEEN EXPOSED TO RAIN OR WATER.  
- IF THE PRODUCT DOES NOT OPERATE NORMALLY BY FOLLOWING  
THE OPERATING INSTRUCTIONS. ADJUST ONLY THOSE CONTROLS THAT  
ARE COVERED BY THE OPERATING INSTRUCTIONS, AS IMPROPER  
ADJUSTMENT OF OTHER CONTROLS MAY RESULT IN DAMAGE, AND  
MAY REQUIRE EXTENSIVE WORK BY A QUALIFIED TECHNICIAN TO  
RESTORE THE PRODUCT TO NORMAL OPERATION.  
PREPARING TO USE THE DC9200 SERIES  
1. Prepare to install the battery into the cordless handset by  
firmly pressing down on the top of the battery cover and  
sliding it off. If cover is secured with a screw, remove the  
screw first.  
2. Locate the lightly embossed numbers “1” and “2” on the  
battery’s plastic connector.  
3. Insert the battery connector into the handset’s connector  
with the embossed numbers facing up.  
Note: The handset may “beep” when the battery is connected. This is not  
an indication that the telephone is ready to use. To obtain optimal perform-  
ance of the telephone, be sure to charge the battery for 15 to 20 hours.  
2. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE  
PRODUCT.  
3. UNPLUG THE PRODUCT FROM THE WALL OUTLET BEFORE CLEANING.  
DO NOT USE LIQUID CLEANER OR AEROSOL CLEANERS. USE A DAMP  
CLOTH FOR CLEANING.  
4. DO NOT USE THIS PRODUCT NEAR WATER, FOR EXAMPLE, NEAR A  
BATHTUB, WASH BOWL, KITCHEN SINK OR LAUNDRY TUB, IN A WET  
BASEMENT, OR NEAR A SWIMMING POOL.  
5. DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND OR  
TABLE. THE PRODUCT MAY FALL, CAUSING SERIOUS DAMAGE TO THE  
PRODUCT.  
6. SLOTS AND OPENINGS IN THE CABINET AND THE BACK OF BOTTOM  
ARE PROVIDED FOR VENTILATION, TO PROTECT IT FROM OVERHEATING.  
THESE OPENINGS MUST NOT BE BLOCKED OR COVERED. THE OPENINGS  
SHOULD NEVER BE BLOCKED BY PLACING THE PRODUCT ON THE BED,  
SOFA, RUG OR ANY OTHER SIMILAR SURFACE. THIS PRODUCT SHOULD  
NEVER BE PLACED NEAR OR OVER A RADIATOR OR HEAT REGISTER.  
BATTERY SAFETY INSTRUCTIONS  
1. Use only Teledex-approved battery replacements.  
2. Dispose of used batteries according to local codes pertaining  
to NiMH batteries.  
- IF THE PRODUCT HAS BEEN DROPPED OR THE CABINET HAS BEEN  
DAMAGED.  
3. Do not dispose of batteries in fire, as they may explode  
4. Charge the telephone's batteries only while in the telephone  
handset, and only by using the telephone base unit to charge.  
Do not attempt to remove the batteries and charge them in  
a separate charging unit.  
5. Do not short-circuit the battery pack, as this may cause it to  
explode or catch fire.  
- IF THE PRODUCT EXHIBIT A DISTINCT CHANGE IN PERFORMANCE.  
10. AVOID USING A TELEPHONE (OTHER THAN A CORDLESS TYPE)  
DURING AN ELECTRICAL STORM. THERE MAY BE A REMOTE RISK OF  
ELECTRIC SHOCK FROM LIGHTNING.  
11. DO NOT USE THE TELEPHONE TO REPORT A GAS LEAK IN THE  
VICINITY OF THE LEAK.  
4. Replace the battery compartment cover and retaining screw.  
5. Insert the provided rubber screw cover.  
PLEASE SAVE THESE INSTRUCTIONS  
6. Turn the telephone base so the back panel is facing you.  
Insert either end of the RJ-45 cable into the jack on the back  
of the telephone labeled LINE.  
7. Insert the other end of the cable into the jack on the AC  
adapter labeled PHONE.  
8. Insert one end of the RJ-11 line cord into the jack on the AC  
adapter labeled LINE.  
HANDSET/BASE REGISTRATION PROCEDURE  
This procedure establishes an exclusive link between a specific  
handset and base, thereby allowing no other access to this  
specific base. To accomplish this procedure, place the handset  
on the base in the charging position. The LINE indicator will  
blink while the process is occuring. This process occurs each  
time the handset is placed on the base in the charging cradle.  
CONTACTING TELEDEX  
Telephone  
(408) 363-3100  
(800) 794-8353  
9. Insert the other end of this line cord into a telephone jack.  
10. Plug the AC adapter into an unswitched electrical outlet.  
11.Once your telephone is connected, remove the plastic  
overlay and place the paper faceplate over the keys. Replace  
the plastic overlay by hooking the tabs on the overlay into  
the recessed slots located on both sides. The overlay is  
easiest to insert when the left or right side tabs are inserted  
first, and the middle of the overlay is slightly bowed to allow  
for insertion of the other tabs.  
ADJUSTING THE RING VOLUME  
The up and down volume keys will adjust the ringer volume of  
the telephone. Additionally, the DC9200 series telephone has an  
optional “courtesy” ring mode, wherein the ring volume begins  
at the lowest setting, then automatically rings louder with each  
successive ring during an incoming call. To select the courtesy  
ring mode, follow these steps:  
Internet  
store.teledex.com  
Email  
Press the FLASH key; then the 4 key; then the STORE key; then  
press the number on the keypad that corresponds to the line for  
which you wish to change to courtesy ring mode, i.e; press the  
number 1 for line 1, and the number 2 for line 2.  
12.Place the cordless handset on the base unit.  
Mailing Address  
6311 San Ignacio Avenue  
CHARGING THE BATTERY  
The rechargeable Nickel Metal Hydride (NiMH) battery must be  
fully charged before using the phone for the first time. It is recom-  
mended that that battery pack be charged for approximately 15  
to 20 hours, without interruption, before use. To charge the battery,  
place the handset, keypad down, in the base unit. Make sure the  
CHARGE LED on the base lights. If the LED does not light:  
San Jose, CA 95119 USA  
To return to regular ring mode: Press the FLASH key; then the 1  
key; then the STORE key; then the number on the keypad that  
corresponds to the line for which you wish to change regular ring  
mode.  
Part Number 600-0480-67A  
Copyright © 2004 Teledex LLC.  
ALL RIGHTS RESERVED.  
ADJUSTING SPEAKERPHONE VOLUME  
1. Ensure that the AC adapter is plugged in.  
2. Ensure that the AC adapter is not plugged into a switched  
electrical outlet.  
The speakerphone has eight (8) levels. To adjust speakerphone  
volume, locate the volume up/down keys, located on the front  
surface of the phone below the keypad. With the speaker active,  
DC9200 SERIES DIAGRAM  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Tecumseh Snow Blower LH195SA User Manual
Tektronix Blood Glucose Meter 524A User Manual
Thule Automobile Accessories Kit 2120 User Manual
Tokina Camera Accessories TC2814 User Manual
Topcom Headphones 300 DECT User Manual
TRENDnet Switch TEG S4000I User Manual
Tripp Lite Power Supply WEXT3 SU8000 User Manual
Uniden Portable Radio PRO501XL User Manual
Vanguard Heating Indoor Fireplace VMH10TN User Manual
Vulcan Hart Charcoal Grill MGCB18 User Manual