7. Plug the telephone line cord into the modular jack and
into the TEL. LINE jack on the back of the base.
LOCAL AREA CODE SETTING
INTRODUCTION
Model EX29350
Spea kerphone
User s Guide
1. Press “MENU” button, LCD displays “set 1 date”.
2. Press “ < ” or “ > ” button, LCD displays “set 2 code”.
3. Press “MENU” button to enter local area code setting.
4. Press 0~9 button to input local area code.
5. Press “DEL” button to save the setting and exit setting
mode.
Your Caller ID phone stores and displays specific
information, provided by your local telephone company, to
subscribers of Caller ID or similar caller identification
services. You must subscribe to one of these services in
order to use this unit.
NOTE: The phone automatically defaults to touch-tone dialing.
To change to pulse (rotary) dialing, see "Tone/Pulse Dialing". If
you don't know which type of service you have, check with the
phone company.
Your Caller ID phone enables you to:
Identify callers before you answer the phone.
Record up to 60 Caller ID messages sequentially.
Know who called while you were away.
To get the most from your new phone, we suggest that
you take a few minutes right now to read through this
user’s guide.
RINGER LEVEL SETTING
There are total 3 ring levels. (HI/MID/LO)
Move ring volume switch in the back of the base to set
Ringer level.
LCD Display Icons
1.
: SPEAKERPHONE
2.
: LOW BATTERY INDICATOR
3. MUTE : MUTE
RECEIVE VOLUME
4.
: NUMBER OF CALLS
IMPORTANT: In order to use this unit, you must subscribe to
either the standard Number Caller ID Service.
There are total 3 receive volume levels. (HI/MID/LO)
While on the phone, press the “VOL” button to adjust the
receive volume of handset or speaker.
5. NEW : NEW CID
6.
: VOICE MAIL
7. REP : REPEAT
(Volume “Lo” displays “ ”, “Mid” displays “
displays “ ”.)
”, “Hi”
8.
9.
: TIME
DATE
BEFORE YOU BEGIN
:
M
D
PARTS CHECKLIST
10. AM : MORNING
FLASH TIME SETTING
Make sure your package includes the items:
11. PM : AFTERNOON
There are three flash timings for selection.
1.
2.
3.
4.
Handset Coiled Cord
Corded Handset
Base
Move the hard switch for selecting flash timing on the
bottom to select proper flash timing .100ms ,300ms ,or
600ms.
FUNCTION KEY
1. SPEAKER
2. REDIAL
3. VOL
Telephone Line Cord
MODULAR JACK REQUIREMENTS
You need an RJ11 type modular phone jack, which is the
most common type of phone jack. If you don’t have a
modular jack, call your local phone company to find out
how to get one installed.
4. CONTRAST
5. STORE
6. DIAL
PHONE BASICS
7. FLASH
8. MUTE
INSTALLING THE PHONE
DESKTOP INSTALLATION
9. DEL
10. <REVIEW>
11. MENU
SET UP
TONE/PULSE DIALING SELECTION
Use a tooling to move T/P switch in the bottom to set
dialing mode. (T: tone or P: pulse.)
IN USE INDICATOR
The “IN USE” indicator will light up when the phone is on the line.
NOTE: The phone is shipped in Tone Dialing Mode from the
SPEAKER INDICATOR
The SPEAKER indicator will light up when the speaker is
manufacturer.
activated.
1. Plug the coiled cord into the corded handset and the base.
2. Push the switch on the battery door to unlock the
FLASH TIME SETTING
Using a tooling to move FLASH switch in the bottom to
Thomson Asia Limited
3/ F.,Delta House,3 On Yiu Street ,
Siu Lek Yuen,Sha tin,Hong Kong
RECEIVING A CALL
1. Check the display to see who is calling.
2. Press the “SPEAKER” button or pick up the handset to
answer the phone.
battery door.(Push the switch to “
”position.)
set FLASH timing. (100ms/300ms/600ms.)
3. Remove the battery compartment door.
is a tradema rk of Genera l Electic compa ny used under license
to Thomson Inc.India na polis,IN 46290
4. Insert 3 sized AA batteries. (Not include in package)
The unit will be at its optimal performance provided that
you have installed the 3 pieces AA sized dry batteries.
5. Put the compartment door back on.
DATEAND TIME SETTING
3. Press the “SPEAKER” button again or put the handset
on cradle to hang up.
1. Press “MENU” button, LCD displays “set 1 date”.
2. Press “MENU” button to enter date/time setting mode.
3. Press 0~9 button to input the year, date and time.
4. Press “DEL” button to save the setting and exit setting
MAKING A CALL
6. Push the switch on the battery door to lock the battery
door.(Push the switch to “ ”position.)
To make a call, press the “SPEAKER” button or pick up
Download from Www.Somanuals.com. All Manuals Search And Download.
mode.
|